Добірка наукової літератури з теми "Multiphase Flow Solver"
Оформте джерело за APA, MLA, Chicago, Harvard та іншими стилями
Ознайомтеся зі списками актуальних статей, книг, дисертацій, тез та інших наукових джерел на тему "Multiphase Flow Solver".
Біля кожної праці в переліку літератури доступна кнопка «Додати до бібліографії». Скористайтеся нею – і ми автоматично оформимо бібліографічне посилання на обрану працю в потрібному вам стилі цитування: APA, MLA, «Гарвард», «Чикаго», «Ванкувер» тощо.
Також ви можете завантажити повний текст наукової публікації у форматі «.pdf» та прочитати онлайн анотацію до роботи, якщо відповідні параметри наявні в метаданих.
Статті в журналах з теми "Multiphase Flow Solver"
1
Lin, Zhipeng, Wenjing Yang, Houcun Zhou, Xinhai Xu, Liaoyuan Sun, Yongjun Zhang, and Yuhua Tang. "Communication Optimization for Multiphase Flow Solver in the Library of OpenFOAM." Water 10, no. 10 (October 16, 2018): 1461. http://dx.doi.org/10.3390/w10101461.
Повний текст джерелаАнотація:
Multiphase flow solvers are widely-used applications in OpenFOAM, whose scalability suffers from the costly communication overhead. Therefore, we establish communication-optimized multiphase flow solvers in OpenFOAM. In this paper, we first deliver a scalability bottleneck test on the typical multiphase flow case damBreak and reveal that the Message Passing Interface (MPI) communication in a Multidimensional Universal Limiter for Explicit Solution (MULES) and a Preconditioned Conjugate Gradient (PCG) algorithm is the short slab of multiphase flow solvers. Furthermore, an analysis of the communication behavior is carried out. We find that the redundant communication in MULES and the global synchronization in PCG are the performance limiting factors. Based on the analysis, we propose our communication optimization algorithm. For MULES, we remove the redundant communication and obtain optMULES. For PCG, we import several intermediate variables and rearrange PCG to reduce the global communication. We also overlap the computation of matrix-vector multiply and vector update with the non-blocking computation. The resulting algorithms are respectively referred to as OFPiPePCG and OFRePiPePCG. Extensive experiments show that our proposed method could dramatically increase the parallel scalability and solving speed of multiphase flow solvers in OpenFOAM approximately without the loss of accuracy.
2
Nguyen, Viet-Bac, Quoc-Vu Do, and Van-Sang Pham. "An OpenFOAM solver for multiphase and turbulent flow." Physics of Fluids 32, no. 4 (April 1, 2020): 043303. http://dx.doi.org/10.1063/1.5145051.
Повний текст джерела
3
Ivanov, E. A., A. S. Klyuyev, A. A. Zharkovskii, and I. O. Borshchev. "Numerical Simulation of Multiphase Flow Structures in Openfoam Software Package." E3S Web of Conferences 320 (2021): 04016. http://dx.doi.org/10.1051/e3sconf/202132004016.
Повний текст джерелаАнотація:
Numerical simulation of various structures of multiphase flow in the pipe was performed using the OpenFOAM software package. A visual comparison of multiphase flow design structures for separated stratified-wave, plug and annular flow modes with experimental data is presented. For multiphase flow modelling the solver compressibleInterFoam was used. From the results of numerical modelling, it follows that the OpenFOAM software package allows correct prediction of multiphase flow modes in the pipe depending on Reynolds numbers for gas and liquid phases of the flow.
4
Li, Wei, and Mathieu Desbrun. "Fluid-Solid Coupling in Kinetic Two-Phase Flow Simulation." ACM Transactions on Graphics 42, no. 4 (July 26, 2023): 1–14. http://dx.doi.org/10.1145/3592138.
Повний текст джерелаАнотація:
Real-life flows exhibit complex and visually appealing behaviors such as bubbling, splashing, glugging and wetting that simulation techniques in graphics have attempted to capture for years. While early approaches were not capable of reproducing multiphase flow phenomena due to their excessive numerical viscosity and low accuracy, kinetic solvers based on the lattice Boltzmann method have recently demonstrated the ability to simulate water-air interaction at high Reynolds numbers in a massively-parallel fashion. However, robust and accurate handling of fluid-solid coupling has remained elusive: be it for CG or CFD solvers, as soon as the motion of immersed objects is too fast or too sudden, pressures near boundaries and interfacial forces exhibit spurious oscillations leading to blowups. Built upon a phase-field and velocity-distribution based lattice-Boltzmann solver for multiphase flows, this paper spells out a series of numerical improvements in momentum exchange, interfacial forces, and two-way coupling to drastically reduce these typical artifacts, thus significantly expanding the types of fluid-solid coupling that we can efficiently simulate. We highlight the numerical benefits of our solver through various challenging simulation results, including comparisons to previous work and real footage.
5
Chen, Guo-Qing, Hongyuan Li, Pengyu Lv, and Huiling Duan. "An improved multiphase lattice Boltzmann flux solver with phase interface compression for incompressible multiphase flows." Physics of Fluids 35, no. 1 (January 2023): 013310. http://dx.doi.org/10.1063/5.0131506.
Повний текст джерелаАнотація:
Numerical dissipation is ubiquitous in multiphase flow simulation. This paper introduces a phase interface compression term into the recently developed multiphase lattice Boltzmann flux solver and achieves an excellent interface maintenance. Here, the phase interface compression term only works in the interface region and is solved as the flux in finite volume discretization. At each cell interface, the interfacial compression velocity [Formula: see text] is determined by local reconstruction velocities of the multiphase lattice Boltzmann flux solver, which maintains the consistency of the flux evaluation. Meanwhile, the interfacial order parameter C in the phase interface compression term is obtained by the second order upwind scheme according to the interface normal direction. Numerical validation of the present model has been made by simulating the Zalesak problem, the single vortex problem, Rayleigh–Taylor instability, and bubble rising and coalescence. The obtained results indicate the validity and reliability of the present model.
6
Guo, Yisen, and Yongsheng Lian. "Calculation of Water Collection Efficiency Using a Multiphase Flow Solver." Journal of Aircraft 56, no. 2 (March 2019): 685–94. http://dx.doi.org/10.2514/1.c034793.
Повний текст джерела
7
Singh, Gurpreet, Gergina Pencheva, and Mary F. Wheeler. "An approximate Jacobian nonlinear solver for multiphase flow and transport." Journal of Computational Physics 375 (December 2018): 337–51. http://dx.doi.org/10.1016/j.jcp.2018.08.043.
Повний текст джерела
8
Jiang, LiJuan, HongGuang Sun, and Yan Wang. "Modeling immiscible fluid flow in fractal pore medium by multiphase lattice Boltzmann flux solver." Physics of Fluids 35, no. 2 (February 2023): 023334. http://dx.doi.org/10.1063/5.0137360.
Повний текст джерелаАнотація:
In this paper, the multiphase lattice Boltzmann flux solver (MLBFS), where the phase field model and the apparent liquid permeability model are built-in, is developed to simulate incompressible multiphase flows in fractal pore structure at the representative elementary volume scale. MLBFS takes advantage of the traditional Navier–Stokes solver (e.g., geometric flexibility and direct handling of complex boundary conditions) and lattice Boltzmann method (e.g., intrinsically kinetic nature, simplicity, and parallelism). It is easily applied to simulate multiphase flows transport in the porous medium with large density ratios and high Reynolds numbers. This study focuses on the fluid flow in fractal pore structures and provides an in-depth discussion of the effects of non-Newtonian index, fractal parameters, and density ratios on multiphase flow. The proposed model is validated with benchmark problems to test the applicability and reliability of the MLBFS in describing fluid flow in fractal pore structures with large density ratios and viscosity ratios. Simulation results show that the fractal parameters (i.e., fractal dimension, tortuous fractal dimension, porosity, and capillary radius ratio) can accurately characterize fractal pore structure and significantly affect the apparent liquid permeability. In addition, the flow rate increases with the fractal dimension and decreases with the tortuous fractal dimension, while both flow rate and apparent liquid permeability decrease as the capillary radius ratio. It is also noteworthy that the effect of nonlinear drag forces cannot be neglected for shear-thickened flows.
9
Abas, Aizat, N. Hafizah Mokhtar, M. H. H. Ishak, M. Z. Abdullah, and Ang Ho Tian. "Lattice Boltzmann Model of 3D Multiphase Flow in Artery Bifurcation Aneurysm Problem." Computational and Mathematical Methods in Medicine 2016 (2016): 1–17. http://dx.doi.org/10.1155/2016/6143126.
Повний текст джерелаАнотація:
This paper simulates and predicts the laminar flow inside the 3D aneurysm geometry, since the hemodynamic situation in the blood vessels is difficult to determine and visualize using standard imaging techniques, for example, magnetic resonance imaging (MRI). Three different types of Lattice Boltzmann (LB) models are computed, namely, single relaxation time (SRT), multiple relaxation time (MRT), and regularized BGK models. The results obtained using these different versions of the LB-based code will then be validated with ANSYS FLUENT, a commercially available finite volume- (FV-) based CFD solver. The simulated flow profiles that include velocity, pressure, and wall shear stress (WSS) are then compared between the two solvers. The predicted outcomes show that all the LB models are comparable and in good agreement with the FVM solver for complex blood flow simulation. The findings also show minor differences in their WSS profiles. The performance of the parallel implementation for each solver is also included and discussed in this paper. In terms of parallelization, it was shown that LBM-based code performed better in terms of the computation time required.
10
Zhou, Houcun, Min Xiang, Shiwei Zhao, and Weihua Zhang. "Development of a multiphase solver for cavitation flow near free surface." Ocean Engineering 188 (September 2019): 106236. http://dx.doi.org/10.1016/j.oceaneng.2019.106236.
Повний текст джерелаДисертації з теми "Multiphase Flow Solver"
1
Heyns, Johan Adam. "Formulation of a weakly compressible two-fluid flow solver and the development of a compressive surface capturing scheme using the volume-of-fluid approach." Thesis, Stellenbosch : Stellenbosch University, 2012. http://hdl.handle.net/10019.1/71934.
Повний текст джерелаАнотація:
Thesis (PhD)--Stellenbosch University, 2012ENGLISH ABSTRACT: This study presents the development and extension of free-surface modelling techniques for the purpose of modelling two-fluid systems accurately and efficiently. The volume-of-fluid (VOF) method is extended in two ways: Firstly, it is extended to account for variations in the gas density through a weakly compressible formulation. Secondly, a compressive free-surface interface capturing formulation that preserves the integrity of the interface shape is detailed. These formulations were implemented and evaluated using the Elemental software. Under certain flow conditions liquid-gas systems may be subjected to large variations in pressure, making it necessary to account for changes in gas density. Modelling this effectively has received relatively little attention in the context of free-surface modelling and remains a challenge to date. To account for the variations in gas density a weakly compressible free-surface modelling formulation is developed for low Mach number flows. The latter is formally substantiated via a non-dimensional analysis. It is proposed that the new formulation advances on existing free-surface modelling formulations by effecting an accurate representation of the dominant physics in an efficient and effective manner. The proposed weakly compressible formulation is discretised using a vertexcentred edge-base finite volume approach, which provides a computationally efficient method of data structuring and memory usage. Furthermore, this implementation is applicable to unstructured spatial discretisation and parallel computing. In this light, the discretisation is formulated to ensure a stable, oscillatory free solution. Furthermore, the governing equations are solved in a fully coupled manner using a combination of dual time-stepping and a Generalised Minimum Residual solver with Lower-Upper Symmetric Gauss-Seidel preconditioning, ensuring a fast and efficient solution. The newly developed VOF interface capturing formulation is proposed to advance on the accuracy and efficiency with which the evolution of the free-surface interface is modelled. This is achieved through a novel combination of a blended higher-resolution scheme, used to interpolate the volume fraction face value, and the addition of an artificial compressive term to the VOF equation. Furthermore, the computational efficiency of the higher-resolution scheme is improved through the reformulation of the normalised variable approach and the implementation of a new higher-resolution blending function. For the purpose of evaluating the newly developed methods, several test cases are considered. It is demonstrated that the new surface capturing formulation offers a significant improvement over existing schemes, particularly at large CFL numbers. It is shown that the proposed method achieves a sharper, better defined interface for a wide range of flow conditions. With the validation of the weakly compressible formulation, it is found that the numerical results correlate well with analytical solutions. Furthermore, the importance of accounting for gas compressibility is demonstrated via an application study. The weakly compressible formulation is also found to result in negligible additional computational cost while resulting in improved convergence rates.
AFRIKAANSE OPSOMMING: Hierdie studie behels die ontwikkeling van numeriese tegnieke met die doel om twee-vloeistof vloei akkuraat en numeries effektief te modelleer. Die volume-vanvloeistof metode word op twee maniere uitgebrei: Eerstens word variasie van die gasdigtheid in ag geneem deur gebruik te maak van ’n swak samedrukbare model. Tweedens saam is ’n hoë-resolusie metode geformuleer vir die voorstelling van die vloeistof-oppervlak. Hierdie uitbreidings is met die behulp van die Elemental programmatuur geïmplementeer en met behulp van die programmatuur geëvalueer. Onder sekere toestande ervaar vloeistof-gas mengsels groot veranderinge in druk. Dit vereis dat die variasie in gasdigtheid in berekening gebring moet word. Die modellering hiervan het egter tot dusver relatief min aandag ontvang. Om hierdie rede word ’n swak samedrukbare model vir lae Mach-getalle voorgestel om die variasie in gasdigtheid in te reken. Die formulering volg uit ’n nie-dimensionele analise. Daar word geargumenteer dat die nuwe formulering die fisika meer akkuraat verteenwoordig. ’n Gesentraliseerde hoekpunt, rant gebaseerde eindige volume metode word gevolg om die differensiaalvergelykings numeries te diskretiseer. Dit bied ’n doeltreffende manier vir datastrukturering en geheuebenutting. Hierdie benadering is verder geskik vir toepassing op ongestruktureerde roosters en parallelverwerking. Die diskretisering is geformuleer om ’n stabiele oplossing sonder numeriese ossillasies te verseker. Die vloeivergelykings word op ’n gekoppelde wyse opgelos deur gebruik te maak van ’n kombinasie van ’n pseudo tyd-stap metode en ’n Veralgemene Minimum Residu berekeningsmetode met Onder-Bo Simmetriese Gauss- Seidel voorafbewerking. Die nuut ontwikkelde skema vir die modellering van die vloeistof-oppervlak is veronderstel om ’n meer akkurate voorstelling te bied en meer doeltreffend te wees vir numeriese berekeninge. Dit word bereik deur die nuwe kombinasie van ’n hoë-resolusie skema, wat gebruik word om die volumefraksie te interpoleer, met die samevoeging van ’n kunsmatige term in die volume-van-vloeistof vergelyking om die resolusie te verfyn. Verder is die doeltreffendheid van die skema verbeter deur die genormaliseerde veranderlikes benadering te herformuleer en deur die ontwikkeling van ’n nuwe hoë-resolusie vermengingsfunksie. Verskeie toetsgevalle is uitgevoer met die doel om die nuwe modelle te evalueer. Daar word aangetoon dat die nuwe skema vir die modellering van die vloeistofoppervlak ’n meetbare verbetering bied, veral by hoër Courant-Friedrichs-Lewy getalle. Die nuwe formulering bied dus hoër akkuraatheid vir ’n wye verskeidenheid van toestande. Vir die swak samedrukbare formulering is daar ’n goeie korrelasie tussen die numeriese resultate en die analitiese oplossing. In ’n toegepassingsgeval word die noodsaaklikheid om die samedrukbaarheid van die gas in ag te neem gedemonstreer. Die addisionele berekening-kostes van die nuwe formulering is weglaatbaar en in sommige gevalle verhoog die tempo waarteen die oplossing konvergeer
2
Lezeau, Patrick A. "An adaptive quasi-Newton coupled multigrid solver for the simulation of steady multiphase flows." Thesis, Cranfield University, 1997. http://hdl.handle.net/1826/4025.
Повний текст джерелаАнотація:
This thesis is concerned with the application of adaptive local quasi-Newton coupled
multigrid (ALQNMG) solvers to the numerical simulation of viscous incompressible
fluids, using the multi-fluid model.
The ALQNMG methodologyh as proven highly successful for single phase flows [1],
leading to solution algorithms which are: (i) robust, (ii) efficient and (iii) accurate.
Its extension to multiphase flows is very challenging because the governing equations
are mathematically complex and their solutions are subject to constraints.
The solver presented here has therefore required a considerable number of specific
algorithmic developments.
The outline of the thesis is as follows: firstly, the modelling and simulation of multiphase
flows are reviewed, together with the different numerical techniques implemented
in the solver. Finite volume discrete multiphase equations are then derived
on structured, staggered grids. Next, having specified the solution algorithm, we
consider the accuracy of the solver. Results from several test cases of varying complexity
are compared with those of a widely used commercial CFD package and good
agreementis obtained.
The question of performance is then addressed in detail, both in terms of robustness
and speed of convergence. Good accelerations are obtained using the multigrid
method but the convergence rates are often not grid-independent. The most likely
explanation is that the discrete operators are highly non-linear and therefore have
different characteristics on different grids. Furthermore, the solution algorithm is
shown to not handle certain multiphase diffusive terms very well. Convergence rates
are much faster than those achieved by single grid solvers and commercial codes
typically by one order of magnitude and often more, although the solver is not fully
optimal.
Finally, adaption is considered. Grids are generated automatically which facilitates
the use of the code and allows error control. It is confirmed that multigrid methods
offer a good framework for the implementation of adaption. Considerable gains in
speed and memory usage, by one further order of magnitude, are achieved.
3
Furfaro, Damien. "Simulation numérique d'écoulements multiphasiques, problèmes à interfaces et changement de phase." Thesis, Aix-Marseille, 2015. http://www.theses.fr/2015AIXM4751/document.
Повний текст джерелаАнотація:
Ce travail porte sur la simulation numérique des écoulements multiphasiques compressibles en déséquilibre de vitesses. Un solveur de Riemann diphasique de type HLLC, à la fois robuste, simple et précis est développé et validé à partir de solutions exactes et de données expérimentales. Cette méthode numérique est étendue au cas 3D non-structuré. Par ailleurs, la construction d’une technique numérique pour la répartition de l’énergie d’une onde de choc dans les différentes phases constituant le milieu est établie et permet le respect des conditions de choc multiphasiques. L’extension multiphasique du solveur de Riemann de type HLLC est réalisée, permettant ainsi la simulation d’une plus large gamme d’applications. Enfin, un modèle de transfert de chaleur et de masse dans un brouillard de gouttes ou nuage de bulles, en présence d’effets couplés de diffusion thermique et massiques, est proposé et dévoile des résultats intéressantsThis work deals with the numerical simulation of compressible multiphase flows in velocity disequilibrium. A HLLC-type two-phase Riemann solver is developed and validated against exact solutions and experimental data. This solver is robust, simple, accurate and entropy preserving. The numerical method is then implemented in 3D unstructured meshes. Furthermore, a numerical technique consisting in enforcing the correct energy partition at a discrete level in agreement with the multiphase shock relations is built. The multiphase extension of the HLLC-type Riemann solver is realized and allows the simulation of a wide range of applications. Finally, a droplet heat and mass transfer model with large range of validity is derived. It is valid in any situation: evaporation, flashing and condensation. It accounts for coupled heat and mass diffusion in the gas phase, thermodynamics of the multi-component gas mixture and heat diffusion inside the liquid droplet, enabling in this way consideration of both droplets heating and cooling phenomena
4
Ananthan, M. "Multiscale Simulations in Multiphase Flows." Thesis, 2017. http://etd.iisc.ac.in/handle/2005/4287.
Повний текст джерелаАнотація:
Matter at small scales is not a continuum. Whenever we are dealing with phenomena which have disparate time and length scales, we have to rely on multiscale modelling approach in order to capture the complete physics. A common scenario in multiphase flow simulations is the formation of thin fluid films in between colliding fluid masses or between a fluid mass and a surface. These films are very thin (O(100nm)) and during the Direct Numerical Simulations (DNS) of multiphase flows it is impractical to resolve their thickness fully due to highly disparate time and length scales. Our approach here is to couple a complex thin film model derived analytically to a finite volume solver (and can also be used for standard interface capturing technique like Volume of Fluid method) so that we can capture the formation and evolution of thin films which come into existence in the sub-grid thickness. In the present work, we have formulated a thin film model where viscous forces, surface tension forces and long-range intermolecular forces play the dominant role. Since the modelled equation is highly stiff in nature and these films in realistic scenarios are spread over a large area, we have developed a parallel solver for solving the resulting set of equations. We propose an algorithm to couple the thin film model to a finite volume solver. First, we study a simple square domain containing a single phase, undergoing a shear flow with periodic flow in the horizontal direction, that is simulated using finite volume method coupled to a complex thin film model. Next, we develop a robust multiphase flow solver using Coupled Level-set Volume of Fluid method as the interface capturing technique and propose an algorithm to couple the rigorously validated multiphase solver to the thin film model.
5
Kadioglu, Samet Y. Sussman Mark M. "All speed multi-phase flow solvers." Diss., 2005. http://etd.lib.fsu.edu/theses/available/etd-07012005-152645.
Повний текст джерелаАнотація:
Thesis (Ph. D.)--Florida State University, 2005.Advisor: Mark Sussman, Florida State University, College of Arts and Sciences, Dept. of Mathematics. Title and description from dissertation home page (viewed Oct. 12, 2005). Document formatted into pages; contains xi, 104 pages. Includes bibliographical references.
6
Thompson, Travis Brandon. "Results towards a Scalable Multiphase Navier-Stokes Solver for High Reynolds Number Flows." Thesis, 2013. http://hdl.handle.net/1969.1/151245.
Повний текст джерелаАнотація:
The incompressible Navier-Stokes equations have proven formidable for nearly a century. The present difficulties are mathematical and computational in nature; the computational requirements, in particular, are exponentially exacerbated in the presence of high Reynolds number. The issues are further compounded with the introduction of markers or an immiscible fluid intended to be tracked in an ambient high Reynolds number flow; despite the overwhelming pragmatism of problems in this regime, and increasing computational efficacy, even modest problems remain outside the realm of direct approaches.
Herein three approaches are presented which embody direct application to problems of this nature. An LES model based on an entropy-viscosity serves to abet the computational resolution requirements imposed by high Reynolds numbers and a one-stage compressive flux, also utilizing an entropy-viscosity, aids in accurate, efficient, conservative transport, free of low order dispersive error, of an immiscible fluid or tracer. Finally, an integral commutator and the theory of anti-dispersive spaces is introduced as a novel theoretical tool for consistency error analysis; in addition the material engenders the construction of error-correction techniques for mass lumping schemes.
Книги з теми "Multiphase Flow Solver"
1
Al-Safran, Eissa M., and James P. Brill. Applied Multiphase Flow in Pipes and Flow Assurance: Oil and Gas Production. Society of Petroleum Engineers, 2017. http://dx.doi.org/10.2118/9781613994924.
Повний текст джерелаАнотація:
Applied Multiphase Flow in Pipes and Flow Assurance - Oil and Gas Production delivers the most recent advancements in multiphase flow technology while remaining easy to read and appropriate for undergraduate and graduate petroleum engineering students. Responding to the need for a more up-to-the-minute resource, this highly anticipated new book represents applications on the fundamentals with new material on heat transfer in production systems, flow assurance, transient multiphase flow in pipes and the TUFFP unified model. The complex computation procedure of mechanistic models is simplified through solution flowcharts and several example problems. Containing over 50 solved example problems and 140 homework problems, this new book will equip engineers with the skills necessary to use the latest steady-state simulators available.
Частини книг з теми "Multiphase Flow Solver"
1
Knodel, Markus M., Serge Kräutle, and Peter Knabner. "Global Implicit Solver for Multiphase Multicomponent Flow in Porous Media with Multiple Gas Phases and General Reactions." In Finite Volumes for Complex Applications IX - Methods, Theoretical Aspects, Examples, 595–603. Cham: Springer International Publishing, 2020. http://dx.doi.org/10.1007/978-3-030-43651-3_56.
Повний текст джерела
2
Manzanero, Juan, Carlos Redondo, Gonzalo Rubio, Esteban Ferrer, Eusebio Valero, Susana Gómez-Álvarez, and Ángel Rivero-Jiménez. "A High-Order Discontinuous Galerkin Solver for Multiphase Flows." In Lecture Notes in Computational Science and Engineering, 313–23. Cham: Springer International Publishing, 2020. http://dx.doi.org/10.1007/978-3-030-39647-3_24.
Повний текст джерела
3
Ullah, Hafiz Khadim, Sikiru Oluwarotimi Ismail, and Kumar Shantanu Prasad. "Assessment of Effectiveness of Hollow Fins for Performance Enhancement of Solar Still Device Using Simulation Approach." In Springer Proceedings in Energy, 145–55. Cham: Springer Nature Switzerland, 2023. http://dx.doi.org/10.1007/978-3-031-30960-1_15.
Повний текст джерелаАнотація:
AbstractUnavailability of relatively clean water for several industrial, domestic and agricultural purposes is a serious concern to many regions of the world today. This challenge is growing worse with the increasing world global warming and human population. Therefore, there is need to research into an innovative, sustainable and/or improved technology for an efficient and effective solution, such as desalination. Desalination of freely available sea water is considered a promising source of fresh water. Solar radiation is abundant and can be used to desalinate water, using a solar still device. Also, it is important to increase the productivity of the solar still device through hollow fin modification. Therefore, the effectiveness of this improvement was investigated in this study, using an analysis system (ANSYS) Fluent computational fluid dynamic (CFD) simulation. Appropriate models were used to describe the physical processes, including condensation, evaporation, multiphase flow, surface tension and solar radiation. A close agreement between the simulation values of solar energy and the water temperature in the basin was observed when compared with the experimental data from the literature. Velocity of 0.259 m/s, pressure of 55.8 Pa, temperature of 57.85 ºC and mass transfer rate of 1.41 kg/m3/s were obtained in the mid-plane of the improved double slope single basin (DSSB). The degree of improvement was 5–7% when compared with the existing models. Importantly, this process is economically efficient and can support the concepts of sustainability and healthy living, especially in rural areas.
4
"Multiphase Lattice Boltzmann Flux Solver for Two-Phase Flows." In Lattice Boltzmann and Gas Kinetic Flux Solvers, 116–52. WORLD SCIENTIFIC, 2020. http://dx.doi.org/10.1142/9789811224690_0004.
Повний текст джерелаТези доповідей конференцій з теми "Multiphase Flow Solver"
1
Peña-Monferrer, C., J. L. Muñoz-Cobo, G. Monrós-Andreu, and S. Chiva. "Development of a multiscale solver with sphere partitioning tracking." In MULTIPHASE FLOW 2015. Southampton, UK: WIT Press, 2015. http://dx.doi.org/10.2495/mpf150221.
Повний текст джерела
2
Varadarajan, P. A., and P. S. Hammond. "Flux corrected transport solver for solving 1D multiphase equations for drilling applications." In MULTIPHASE FLOW 2013. Southampton, UK: WIT Press, 2013. http://dx.doi.org/10.2495/mpf130151.
Повний текст джерела
3
Afaq, Muhammad Aaqib, Stefan Turek, Abderrahim Ouazzi, and Arooj Fatima. "Monolithic Newton-Multigrid Solver for Multiphase Flow Problems with Surface Tension." In VI ECCOMAS Young Investigators Conference. València: Editorial Universitat Politècnica de València, 2021. http://dx.doi.org/10.4995/yic2021.2021.12390.
Повний текст джерелаАнотація:
We have developed a monolithic Newton-multigrid solver for multiphase flow problems which solves velocity, pressure and interface position simultaneously. The main idea of our work is based on the formulations discussed in [1], where it points out the feasibility of a fully implicit monolithic solver for multiphase flow problems via two formulations, a curvature-free level set approach and a curvature-free cutoff material function approach. Both formulations are fully implicit and have the advantages of requiring less regularity, since neither normals nor curvature are explicitly calculated, and no capillary time restriction. Furthermore, standard Navier-Stokes solvers might be used, which do not have to take into account inhomogeneous force terms. The reinitialization issue is integrated with a nonlinear terms within the formulations.The nonlinearity is treated with a Newton-type solver with divided difference evaluation of the Jacobian matrices. The resulting linearized system inside of the outer Newton solver is a typical saddle point problem which is solved using the geometrical multigrid with Vanka-like smoother using higher order stable FEM pair $Q_2/P^{\text{disc}}_1$ for velocity and pressure and $Q_2$ for all other variables. The method is implemented into an existing software packages for the numerical simulation of multiphase flows (FeatFlow). The robustness and accuracy of this solver is tested for two different test cases, i.e. static bubble and oscillating bubble, respectively [2].REFERENCES[1] Ouazzi, A., Turek, S. and Damanik, H. A curvature-free multiphase flow solver via surface stress-based formulation. Int. J. Num. Meth. Fluids., Vol. 88, pp. 18–31, (2018).[2] Afaq, M. A., Turek, S., Ouazzi, A. and Fatima, A. Monolithic Newton-Multigrid Solver for Multiphase Flow Problems with Surface Tension. Ergebnisberichte des Instituts fuer Angewandte Mathematik Nummer 636, Fakultaet fuer Mathematik, TU Dortmund University, 636, 2021.
4
Kotteda, V. M. Krushnarao, Ashesh Chattopadhyay, Vinod Kumar, and William Spotz. "Next-Generation Multiphase Flow Solver for Fluidized Bed Applications." In ASME 2017 Fluids Engineering Division Summer Meeting. American Society of Mechanical Engineers, 2017. http://dx.doi.org/10.1115/fedsm2017-69555.
Повний текст джерелаАнотація:
A framework is developed to integrate MFiX (Multiphase Flow with Interphase eXchanges) with advanced linear solvers in Trilinos. MFiX is a widely used open source general purpose multiphase solver developed by National Energy Technology Laboratories and written in Fortran. Trilinos is an objected-oriented open source software development platform from Sandia National Laboratories for solving large scale multiphysics problems. The framework handles the different data structures in Fortran and C++ and exchanges the information from MFiX to Trilinos and vice versa. The integrated solver, called MFiX-Trilinos hereafter, provides next-generation computational capabilities including scalable linear solvers for distributed memory massively parallel computers. In this paper, the solution from the standard linear solvers in MFiX-Trilinos is validated against the same from MFiX for 2D and 3D fluidized bed problems. The standard iterative solvers considered in this work are Bi-Conjugate Gradient Stabilized (BiCGStab) and Generalized minimal residual methods (GMRES) as the matrix is non-symmetric in nature. The stopping criterion set for the iterative solvers is same. It is observed that the solution from the integrated solver and MFiX is in good agreement.
5
Hosangadi, A., R. Lee, B. York, N. Sinha, and S. Dash. "A three-dimensional unstructured flow solver for reacting multiphase propulsive flows." In 33rd Aerospace Sciences Meeting and Exhibit. Reston, Virigina: American Institute of Aeronautics and Astronautics, 1995. http://dx.doi.org/10.2514/6.1995-258.
Повний текст джерела
6
Sementilli, Mae L., Matthew McGurn, and James M. Chen. "A Scalable Multiphase Flow Solver for Simulation of Hybrid Rocket Motors." In AIAA SCITECH 2023 Forum. Reston, Virginia: American Institute of Aeronautics and Astronautics, 2023. http://dx.doi.org/10.2514/6.2023-0279.
Повний текст джерела
7
Lagumbay, Randy S., Oleg V. Vasilyev, Andreas Haselbacher, and Jin Wang. "Numerical Simulation of a High Pressure Supersonic Multiphase Jet Flow Through a Gaseous Medium." In ASME 2004 International Mechanical Engineering Congress and Exposition. ASMEDC, 2004. http://dx.doi.org/10.1115/imece2004-61008.
Повний текст джерелаАнотація:
Computational Fluid Dynamics (CFD) analysis is used to numerically study the structure and dynamics of a high-pressure, high-speed jet of a gas/liquid mixture through a gaseous medium close to the nozzle region. The complex structure of the jet near the nozzle region is captured before it breaks-up downstream. A new multiphase model based on a mixture formulation of the conservation laws for a multiphase flows is used in the simulation. The model does not require ad-hoc closure for the variation of mixture density with pressure and yields thermodynamically accurate acoustic propagation for multiphase mixtures. The numerical formulation has been implemented to a multi-physics unstructured code “RocfluMP” that solves the modified three-dimensional time-dependent Euler/Navier-Stokes equations for a multiphase framework in integral form. The Roe’s approximate Riemann solver is used to allow capturing of shock waves and contact discontinuities. For a very steep gradient, an HLLC scheme is used to resolved the isolated shock and contact waves. The developed flow solver provides a general coupled incompressible-compressible multiphase framework that can be applied to a variety of supersonic jet flow problems including fuel injection systems, thermal and plasma spray coating, and liquid-jet machining. Preliminary results for shock tube analysis and gas/liquid free surface jet flow through a gaseous medium are presented and discussed.
8
Li, Z., and M. Shahvali. "An Efficient Solver for Nonlinear Multiphase Flow Based on Adaptive Coupling of Flow and Transport." In ECMOR XIV - 14th European Conference on the Mathematics of Oil Recovery. Netherlands: EAGE Publications BV, 2014. http://dx.doi.org/10.3997/2214-4609.20141770.
Повний текст джерела
9
Akhtar, M. Wasy, and Holley C. Love. "Computations of Single and Multiphase Flows Using a Lattice Boltzmann Solver." In ASME 2019 Pressure Vessels & Piping Conference. American Society of Mechanical Engineers, 2019. http://dx.doi.org/10.1115/pvp2019-93817.
Повний текст джерелаАнотація:
Abstract There is considerable interest in high fidelity simulation of both single phase incompressible flows and multiphase flows. Most commonly applied numerical methods include finite difference, finite volume, finite element and spectral methods. All of these methods attempt to capture the flow details by solving the Navier–Stokes equations. Challenges of solving the Navier–Stokes single phase incompressible flows include the non-locality of the pressure gradient, non-linearity of the advection term and handling the pressure-velocity coupling. Multiphase flow computations pose additional challenges, such as property and flow variable discontinuities at the interface, whose location and orientation is not known a priori. Further, capturing/tracking of the multiphase interface requires solution of an additional advection equation. Recently, the lattice Boltzmann method has been applied to compute fluid dynamics simulations both for single and multiphase configurations; it is considered a modern CFD approach with improved accuracy and performance. Specifically, we employ a multiple-relaxation time (MRT) technique for the collision term on a D3Q27 lattice. The multiphase interface is captured using the phase-field approach of Allen-Cahn. Test cases include lid driven cavity, vortex shedding for a double backward facing step, Rayleigh Taylor instability, Enright’s deformation test and rising bubble in an infinite domain. These test cases validate different aspects of the single and multiphase model, so that the results can be interpreted with confidence that the underlying computational framework is sufficiently accurate.
10
Li, Huiying, Sergio A. Vasquez, and Peter Spicka. "Advanced Computational Modeling of Multiphase Boiling Flow and Heat Transfer." In ASME 2010 International Mechanical Engineering Congress and Exposition. ASMEDC, 2010. http://dx.doi.org/10.1115/imece2010-38785.
Повний текст джерелаАнотація:
Numerical simulation of boiling flow and heat transfer presents a number of unique challenges in both theoretical modeling and developing robust numerical methodology. The major difficulty arises due to the heat transfer and phase changes between heated walls and fluid (liquid and vapor). Furthermore, modeling of the liquid-vapor interfacial transfers of momentum, heat and mass proves to be equally challenging. The multiphase boiling modeling approach described in this paper has been found to be capable of addressing these issues and is therefore suitable for inclusion in an advanced general purpose CFD solver. In the present approach, boiling flows are modeled within the framework of the Eulerian multifluid model. The governing equations solved are phase continuity, momentum and energy equations. Turbulence effects can be accounted for using mixture, dispersed or per-phase multiphase turbulence models. Wall boiling phenomena are modeled using the baseline mechanistic RPI model for nucleate boiling, and its extensions to non-equilibrium boiling and critical heat flux regime. A range of sub-models are considered to account for the interfacial momentum, mass and heat transfer, and flow regime transitions. An advanced numerical scheme has been developed for solving the model equations which can handle the heat partition between heated walls and fluid, provide for wall and interfacial mass transfer source terms in phase volume fraction equations, and address the coupling between the phase change rates and the pressure correction equation. The wall boiling models and numerical algorithm have been implemented in an advanced, general-purpose CFD code, FLUENT. Validations have been carried out for a range of 2D and 3D boiling flows, including pressurized water through a vertical pipe with heated walls, R-113 liquid in a vertical annulus with internal heated walls, a 3D BRW core channel geometry with vertical heated rods, and water in a vertical circular pipe under critical heat flux and post dry-out conditions. The results demonstrate that the wall boiling models are able to correctly predict the wall temperature and vapor volume fraction distribution. The predictions in all the cases are in reasonable good agreement with available experiments. Tests also indicate that the present implementation is fast and robust, as compared to previous approaches. All the cases are able to be simulated with the use of the FLUENT steady-state multiphase solver with reasonable numbers of iterations.
Звіти організацій з теми "Multiphase Flow Solver"
1
Park, HeeHo Daniel. Innovative Linear and Nonlinear Solvers for Simulating Multiphase Flow within Large-Scale Engineered Subsurface Systems. Office of Scientific and Technical Information (OSTI), October 2019. http://dx.doi.org/10.2172/1570403.
Повний текст джерела