Дисертації з теми "Longitudinal vehicle dynamic"

The main objective of the present thesis focuses on the integration of the in-wheel electric motors into the conception and control of road vehicles. The present thesis is the subject of the grant 186-654 (2010-2013) between the Laboratory of Signals and Systems (L2S-CNRS) and the French Institute of Petrol and New Energies (IFPEN). The thesis work has originally started from a vehicular electrification project, equipped with in-wheel electric motors at the rear axle, to obtain a full electric urban use and a standard extra-urban use with energy recovery at the rear axle in braking phases. The standard internal combustion engines have the disadvantage that complex estimation techniques are necessary to compute the instantaneous engine torque. At the same time, the actuators that control the braking system have some delays due to the hydraulic and mechanical circuits. These aspects represent the primary motivation for the introduction and study of the integration of the electric motor as unique propelling source for the vehicle. The advantages brought by the use of the electric motor are revealed and new techniques of control are set up to maximize its novelty. Control laws are constructed starting from the key feature of the electric motor, which is the fact that the torque transmitted at the wheel can be measured, depending on the current that passes through the motor. Another important feature of the electric motor is its response time, the independent control, as well as the fact that it can produce negative torques, in generator mode, to help decelerate the vehicle and store energy at the same time. Therefore, the novelty of the present work is that the in-wheel electric motor is considered to be the only control actuator signal in acceleration and deceleration phases, simplifying the architecture of the design of the vehicle and of the control laws. The control laws are focused on simplicity and rapidity in order to generate the torques which are transmitted at the wheels. To compute the adequate torques, estimation strategies are set up to produce reliable maximum friction estimation. Function of this maximum adherence available at the contact between the road and the tires, an adequate torque will be computed in order to achieve a stable wheel behavior in acceleration as well as in deceleration phases. The critical issue that was studied in this work was the non-linearity of the tire-road interaction characteristics and its complexity to estimate when it varies. The estimation strategy will have to detect all changes in the road-surface adherence and the computed control law should maintain the stability of the wheel even when the maximum friction changes. Perturbations and noise are also treated in order to test the robustness of the proposed estimation and control approaches.

Unidades propulsoras híbrido elétricas são uma alternativa em potencial para a redução do consumo de combustível e emissões de poluentes, quando empregadas em veículos de transporte público. A configuração híbrido elétrica de interesse é a série, na qual as fontes de potência, para o motor elétrico de tração, são compostas por um banco de baterias e uma unidade formada pela junção entre um motor à combustão interna e um gerador. Na presente Dissertação foi realizada a modelagem de um veículo elétrico híbrido série na qual diferentes estratégias de gerenciamento de potência foram investigadas. Dentre as estratégias de interesse, duas são fundamentadas em regras e a terceira em sistemas fuzzy. Resultados obtidos comprovaram que a fundamentada em sistemas fuzzy possibilita maior economia de combustível, permitindo que o motor à combustão interna forneça menos potência, face o emprego das baseadas em regras. Dessa forma, a utilização de sistemas fuzzy no gerenciamento de potência do veículo, permite o emprego de um motor à combustão menos potente, de menor custo, sem o comprometimento do desempenho do veículo. As simulações do presente modelo de veículo híbrido foram realizadas no ambiente Matlab/Simulink® 7.3.0.
Hybrid electric propulsion units are a potential alternative to the reduction of fuel consumption and pollutant emissions, when used in public transport vehicles. The electric hybrid configuration of interest is the series, in which the energy supplies to the traction electric motor are composed of batteries and a unit represented by the connection of an internal combustion engine and a generator. This Dissertation presents the modeling of a series hybrid electric vehicle in which different energy management strategies were investigated. Among the strategies of interest, two are based on rules and one on fuzzy systems. The obtained results proved that the strategy based on fuzzy systems improved the fuel economy, allowing the internal combustion engine to supply less power than the use of the strategies based on rules. Therefore, the use of fuzzy systems in the energy management of the vehicle allows for the adoption of a less potent and cheaper internal combustion engine, without compromising the vehicles performance. The simulations of the present model of the hybrid electric vehicle were performed in the Matlab/Simulink® 7.3.0 environment.

This master´s thesis is focused on chosen dynamic parameters of a sport vehicle represented by student formula Dragon 7 and comparison of these parameters with conventional vehicles represented by two exemplars of ŠKODA Superb III. Driving tests used for the comparison are simulating the real driving situations from the roads in order to possibly use those for the road accident analysis in the future. All the measurements were taken under lower adhesion conditions which might help solving of the road accidents under such conditions in the future. There is also a description of vehicle driving systems and components which have an influence on the vehicle´s driving dynamics incorporated in the thesis.

An autonomous vehicle is a vehicle that is capable of navigating and driving with no human intervention whatsoever through the utilization of various sensors and positioning systems. The possible applications of autonomous vehicles are widespread, ranging from the aerospace industry to the mining and military sectors where the exposure of human operators to the operating conditions is hazardous to their health and safety. Automobile accidents have become the leading cause of death in certain segments of the world population. Removing the human driver from the decision-making process through automation may result in significantly safer highways. Although full autonomy may be the ultimate goal, there is huge scope for systems that aid the driver in decision making or systems that take over from the driver under conditions where the human driver fails. The aim of the longitudinal control system to be implemented on the Land Rover test vehicle in this study is to improve the vehicle’s safety by controlling the vehicle’s longitudinal behaviour. A common problem with sports-utility-vehicles is the low rollover threshold, due to a high centre of gravity. Rather than modifying the vehicle to increase the rollover threshold, the aim of the control system presented here is to prevent the vehicle from exceeding speeds that would cause the vehicle to reach its rollover threshold. In order to develop a control system that autonomously controls the longitudinal degree of freedom, a model of the test vehicle (a 1997 Land Rover Defender 110 Wagon) was developed in MSC.ADAMS/View and validated experimentally. The model accurately captures the response of the test vehicle to supply forces as generated by the engine and demand forces applied through drag, braking and engine braking. Furthermore, the model has been validated experimentally to provide reliable simulation results for lateral and vertical dynamics. The control system was developed by generating a reference speed that the vehicle must track. This reference speed was formulated by taking into account the vehicle’s limits due to lateral acceleration, combined lateral and longitudinal acceleration and the vehicle’s performance capabilities. The control system generates the desired throttle pedal position, hydraulic pressure in the brake lines, clutch position and gear selection as output. The MSC.ADAMS\View model of the test vehicle was used to evaluate the performance of the control system on various racetracks of which the GPS coordinates were available. The simulation results indicate that the control system performs as expected. Finally, the control system was implemented on the test vehicle and the performance was evaluated by conducting field tests in the form of a severe double lane change manoeuvre. The results of the field tests indicated that the control system limited the acceleration vector of the vehicle’s centre of gravity to prescribed limits, as predicted by the simulation results.
Dissertation (MEng)--University of Pretoria, 2013.
gm2014
Mechanical and Aeronautical Engineering
unrestricted

La problématique de cette thèse réside dans la caractérisation et le maintien de la stabilité des Véhicules Légers Tout Terrain (VLTT). Elle se concentre plus particulièrement sur le développement de systèmes de sécurité actifs capables à la fois de prévenir le conducteur des risques encourus mais aussi de les limiter afin d'assurer l'évolution du véhicule dans une zone de stabilité prédéfinie. Comme le cadre expérimental privilégié est l'application à la stabilité des quadricycles légers à moteurs, plus connus sous le terme anglophone "quad", une des contraintes du projet a été de se limiter à un système sensoriel bas-coût afin d'être en mesure d'industrialiser un tel système. En premier lieu, les métriques de stabilité (Transfert de Charge Latéral et Longitudinal : TCLa et TCLo) ont été choisies grâce à une étude préliminaire sur la stabilité des VLTT. Par la suite, une modélisation 2D en roulis et en tangage avec la prise en compte des déplacements du pilote sur le véhicule sont présentées, ce qui permet d'estimer respectivement le TCLa et le TCLo uniquement à partir de la mesure de l'accélération latérale et longitudinale. Étant donné que pour la suite des travaux, l'anticipation du risque de renversement latéral est nécessaire, un modèle 2D en lacet du véhicule est proposé afin d'obtenir un modèle analytique décrivant la dynamique latérale du véhicule. La suite du mémoire présente les différentes techniques d'observation proposées pour l'estimation des variables et paramètres non-directement mesurables du modèle en lacet du véhicule et qui influencent sa stabilité latérale : les glissements, les conditions d'adhérence et les inclinaisons du véhicule. Plusieurs observateurs ont été proposés, dont le dernier permet de considérer des conditions d'adhérence différentes entre les essieux avant et arrière en utilisant plus largement les accélérations mesurées. Cela permet d'intégrer les passages de sous- à sur-vireur qu'il est essentiel de considérer quand on étudie la stabilité de ce type de véhicule. Ainsi, l'estimation des glissements est toujours pertinente, ce qui permet d'obtenir par la suite une meilleure prédiction de la métrique de stabilité latérale (TCLa) quel que soit le comportement du véhicule. Puis en s'appuyant sur les estimations des observateurs couplées aux modèles dynamiques du véhicule et sur l'extrapolation des commandes du conducteur sur un horizon de prédiction, il est possible de prédire les évolutions du TCLa. Cette valeur prédite ainsi que les estimations en ligne des métriques de stabilité constituent alors le point d'entrée pour la synthétisation d'un système de sécurité actif dédié aux VLTT. Celui-ci est basé sur la génération d'un retour d'effort au niveau de la gâchette des gaz permettant soit d'informer le pilote du risque encouru par la création d'une sensation de dureté, soit d'imposer le retour complet de la gâchette des gaz, ce qui implique une diminution de la vitesse et donc la réduction du risque. Finalement, dans le cas où il est possible de maîtriser la vitesse du véhicule par l'installation d'un système de rétroaction sur les freins (Quad haut de gamme ou robot mobile), les derniers travaux présentés s'intéressent aux techniques de commande prédictive à modèle afin de calculer en temps-réel la vitesse maximale admissible, qui assure l'évolution du critère de stabilité choisi dans un domaine de stabilité. Les modèles, les observateurs, la prédiction du TCLa et les 2 systèmes de prévention présentés dans ce mémoire ont été validés et testés au travers de simulations avancées et d'essais expérimentaux réalisés sur un quad agricole et un robot autonome. Il apparaît alors qu'en plus d'être efficace pour la prévention des risques de renversement à hautes dynamiques, le système de sécurité est industriellement viable. Cela a été rendu possible grâce à une conception reposant uniquement sur des actionneurs et un système sensoriel, dont les coûts sont en adéquation avec le prix d'un VLTT.

The vehicles of tomorrow will be more sophisticated, intelligent and safe than the vehicles of today. The future is leaning towards fully autonomous vehicles. This degree project provides a data driven solution for a speed adaptation system that can be used to compute a vehicle speed for curves, suitable for the underlying driving style of the driver, road properties and weather conditions. A speed adaptation system for curves aims to compute a vehicle speed suitable for curves that can be used in Advanced Driver Assistance Systems (ADAS) or in Autonomous Driving (AD) applications. This degree project was carried out at Volvo Car Corporation. Literature in the field of speed adaptation systems and factors affecting the vehicle speed in curves was reviewed. Naturalistic driving data was both collected by driving and extracted from Volvo's data base and further processed. A novel speed adaptation system for curves was invented, implemented and evaluated. This speed adaptation system is able to compute a vehicle speed suitable for the underlying driving style of the driver, road properties and weather conditions. Two different artificial neural networks and two mathematical models were used to compute the desired vehicle speed in curves. These methods were compared and evaluated.
Morgondagens fordon kommer att vara mer sofistikerade, intelligenta och säkra än dagens fordon. Framtiden lutar mot fullständigt autonoma fordon. Detta examensarbete tillhandahåller en datadriven lösning för ett hastighetsanpassningssystem som kan beräkna ett fordons hastighet i kurvor som är lämpligt för förarens körstil, vägens egenskaper och rådande väder. Ett hastighetsanpassningssystem för kurvor har som mål att beräkna en fordonshastighet för kurvor som kan användas i Advanced Driver Assistance Systems (ADAS) eller Autonomous Driving (AD) applikationer. Detta examensarbete utfördes på Volvo Car Corporation. Litteratur kring hastighetsanpassningssystem samt faktorer som påverkar ett fordons hastighet i kurvor studerades. Naturalistisk bilkörningsdata samlades genom att köra bil samt extraherades från Volvos databas och bearbetades. Ett nytt hastighetsanpassningssystem uppfanns, implementerades samt utvärderades. Hastighetsanpassningssystemet visade sig vara kapabelt till att beräkna en lämplig fordonshastighet för förarens körstil under rådande väderförhållanden och vägens egenskaper. Två olika artificiella neuronnätverk samt två matematiska modeller användes för att beräkna fordonets hastighet. Dessa metoder jämfördes och utvärderades.

Orientador: Franco Giuseppe Dedini
Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Mecânica
Made available in DSpace on 2018-08-22T04:27:38Z (GMT). No. of bitstreams: 1 Eckert_JonyJavorski_M.pdf: 14458146 bytes, checksum: b2eb0f5d4618d1873858f49c66965bec (MD5) Previous issue date: 2013
Resumo: Dinâmica veicular é o estudo das interações entre o veículo, condutor e o ambiente bem como as reações de carga, sendo esta dividida em 3 grandes áreas: dinâmica longitudinal, vertical e lateral. Existem variações entre os métodos propostos pela literatura para o cálculo da dinâmica longitudinal do veículo, sendo que o objetivo deste trabalho é, por meio de simulações, compararem os resultados obtidos pelas diversas metodologias. Por meio de um modelo gerado com auxílio do programa de análise dinâmica de multicorpos Adams®, juntamente com o Simulink Matlab®, foram implementados os métodos de cálculo propostos pela literatura de forma a simular o comportamento de um veículo em função de uma demanda de potência gerada por meio do padrão de velocidades imposto pelos ciclos das normas brasileiras NBR6601 e NBR7024. Os resultados encontrados foram comparados por meio da correlação linear entre as curvas de torque resultantes do modelo dinâmico, possibilitando uma avaliação entre os resultados encontrados pelos diferentes métodos. Também foram avaliados o consumo de combustível, a influência da variação da massa do veículo e da estratégia de condução no comportamento dinâmico do veículo, bem como modelos complementares referentes a veículos híbridos e o efeito da adição de um modelo de embreagem no conjunto simulado
Abstract: Vehicular dynamics is the study of interactions between vehicle, driver and load reactions. The vehicular dynamics is divided into three areas: longitudinal, vertical and lateral. There are variations between the methods proposed in the literature to calculate the longitudinal dynamics of the vehicle. The purpose of this study is, through simulations; compare the results obtained by different methods. By means of a model generated by Adams® (Software of Multibody Dynamics Analysis) together with Simulink Matlab® were implemented the calculation methods proposed by literature to simulate the behavior of a vehicle according to a power demand resulting from the default speeds cycles required by Brazilian Standards NBR6601 and NBR7024. The results were compared using linear correlation between the couple curves resulting from the dynamic model, allowing an evaluation of the results reported by different methods. Were also evaluated: the fuel consumption and the influence of the mass vehicle variation, the driving strategy in the vehicle dynamic behavior, some complementary models of hybrid vehicles and the effect of add a clutch model
Mestrado
Mecanica dos Sólidos e Projeto Mecanico
Mestre em Engenharia Mecânica

This master's thesis designs acceleration and deceleration measurement method by a test drive. It contains also measurement realisation, design of the computational model and acquired data analysis and evaluation.

The transportation sector is responsible for the majority of airborne particles and global energy consumption in urban areas. Its role in generating air pollution in urban areas is even more critical, as many visitors, commuters and citizens travel there daily for various reasons. Emissions released by transport fleets have an exhaust (tailpipe) and a non-exhaust (brake wears ) origin. Both exhaust and non-exhaust airborne particles can have destructive effects on the human cardiovascular and respiratory systems and even lead to premature deaths. This dissertation aims to estimate the amount of exhaust and brake emissions in a real case study by proposing an innovative methodology. For this purpose, different levels of study have been introduced, including the subsystem level, the system level, the environmental level and the suprasystem level. To address these levels, two approaches were proposed along with a data collection process. First, a comprehensive field survey was conducted in the area of Buonconsiglio Castle and data was collected on traffic and non-traffic during peak hours. Then, in the first approach, a state-of-the-art simulation-based method was presented to estimate the amount of exhaust emissions generated and the rate of fuel consumption in the case study using the VISSIM traffic microsimulation software and Enviver emission modeler at the suprasystem level. In order to calculate the results under different mobility conditions, a total of 18 scenarios were defined based on changes in vehicle speeds and the share of heavy vehicles (HV%) in the modal split. Subsequently, the scenarios were accurately modelled in the simulation software VISSIM and repeated 30 times with a simulation runtime of three hours. The results of the first approach confirmed the simultaneous effects of considering vehicle speed and HV % on fuel consumption and the amount of exhaust emissions generated. Furthermore, the sensitivity of exhaust emissions and fuel consumption to variations in vehicle speed was found to be much higher than HV %. In other words, the production of NOx and VOC emissions can be increased by up to 20 % by increasing the maximum speed of vehicles by 10 km/h. Conversely, increasing the HV percentage at the same speed does not seem to produce a significant change. Furthermore, increasing the speed from 30 km/h to 50 km/h increased CO emissions and fuel consumption by up to 33%. Similarly, a reduction in speed of 20 or 10 km/h with a 100% increase in HV resulted in a 40% and 27% decrease in exhaust emissions per seat, respectively. In the second approach, a novel methodology was proposed to estimate the number of brake particles in the case study. To achieve this goal, a downstream approach was proposed starting from the suprasystem level (microscopic traffic simulation models in VISSIM) and using a developed mathematical vehicle dynamics model at the system level to calculate the braking torques and angular velocities of the front and rear wheels, and proposes an artificial neural network (ANN) as a brake emission model, which has been appropriately trained and validated using emission data collected through more than 1000 experimental tribological tests on a reduced-scale dynamometer at the subsystem level (braking system). Consideration of this multi-level approach, from tribological to traffic-related aspects, is necessary for a realistic estimation of brake emissions. The proposed method was implemented on a targeted vehicle, a dominant SUV family car in the case study, considering real driving conditions. The relevant dynamic quantities of the targeted vehicle (braking torques and angular velocities of the wheels) were calculated based on the vehicle trajectory data such as speed and deceleration obtained from the traffic microsimulation models and converted into braking emissions via the artificial neural network. The total number of brake emissions emitted by the targeted vehicles was predicted for 10 iterations route by route and for the entire traffic network. The results showed that a large number of brake particles (in the order of billions of particles) are released by the targeted vehicles, which significantly affect the air quality in the case study. The results of this dissertation provide important information for policy makers to gain better insight into the rate of exhaust and brake emissions and fuel consumption in metropolitan areas and to understand their acute negative impacts on the health of citizens and commuters.

This diploma thesis deals with the possibilities of determining the influence of electronic stability systems on the chassis of the vehicle driving dynamics. In the introductory section is made theoretical analysis of road vehicle dynamics. Further description is made of some stabilization systems and situations and how to solve them by using these systems. Chapter 6.2.1 describes the methodology of practical experiment, which can determine influence of the stability system of the vehicle chassis on driving dynamics. The next chapter describes an experiment conducted and interpreted the measured values. The penultimate chapter is a simulation of this experiment using simulation software Virtual Crash. The last chapter is an evaluation of the experiment and compares the results with simulation programs using the same input conditions. The conclusion summarizes the results of this work.

La voiture autonome pourrait réduire le nombre de morts et de blessés sur les routes tout en améliorant l'efficacité du trafic. Cependant, afin d'assurer leur déploiement en masse sur les routes ouvertes au public, leur sécurité doit être garantie en toutes circonstances. Cette thèse traite de l'architecture de planification et de contrôle pour la conduite automatisée et défend l'idée que l'intention du véhicule doit correspondre aux actions réalisées afin de garantir la sécurité à tout moment. Pour cela, la faisabilité cinématique et dynamique de la trajectoire de référence doit être assurée. Sinon, le contrôleur, aveugle aux obstacles, n'est pas capable de la suivre, entraînant un danger pour la voiture elle-même et les autres usagers de la route. L'architecture proposée repose sur la commande à modèle prédictif fondée sur un modèle bicyclette cinématique afin de planifier des trajectoires de référence sûres. La faisabilité de la trajectoire de référence est assurée en ajoutant une contrainte dynamique sur l'angle au volant, contrainte issue de ces travaux, afin d'assurer que le modèle bicyclette cinématique reste valide. Plusieurs contrôleurs à haute-fréquence sont ensuite comparés afin de souligner leurs avantages et inconvénients. Enfin, quelques résultats préliminaires sur les contrôleurs à base de commande sans modèle et leur application au contrôle automobile sont présentés. En particulier, une méthode efficace pour ajuster les paramètres est proposée et implémentée avec succès sur la voiture expérimentale de l'ENSIAME en partenariat avec le laboratoire LAMIH de Valenciennes
Autonomous vehicles are believed to reduce the number of deaths and casualties on the roads while improving the traffic efficiency. However, before their mass deployment on open public roads, their safety must be guaranteed at all time.Therefore, this thesis deals with the motion planning and control architecture for autonomous vehicles and claims that the intention of the vehicle must match with its actual actions. For that purpose, the kinematic and dynamic feasibility of the reference trajectory should be ensured. Otherwise, the controller which is blind to obstacles is unable to track it, setting the ego-vehicle and other traffic participants in jeopardy. The proposed architecture uses Model Predictive Control based on a kinematic bicycle model for planning safe reference trajectories. Its feasibility is ensured by adding a dynamic constraint on the steering angle which has been derived in this work in order to ensure the validity of the kinematic bicycle model. Several high-frequency controllers are then compared and their assets and drawbacks are highlighted. Finally, some preliminary work on model-free controllers and their application to automotive control are presented. In particular, an efficient tuning method is proposed and implemented successfully on the experimental vehicle of ENSIAME in collaboration with the laboratory LAMIH of Valenciennes

Este trabalho tem como objetivo estudar a influência da geometria de suspensão do veículo nas atitudes da massa suspensa. Apresenta um confronto entre obras e autores e está segmentada em três partes; onde na primeira parte são definidos os conceitos básicos como dive, squat, lift, anti-dive, anti-squat, anti-lift e equivalente trailing-arm; na segunda parte são apresentadas as limitações e os novos conceitos definidos por R. S. Sharp e na terceira parte é apresentado o modelo dinâmico bidimensional introduzido por Fu-Cheng Wang. Apresenta um modelo virtual em sistema de multi-corpos desenvolvido no programa ADAMS, com todos os subsistemas que compõe um veículo completo. Inova ao trazer como objeto de estudo um veículo de competição (fórmula SAE) que possui como particularidade o sistema de suspensão push-rod. Surpreende com os resultados obtidos, pois, contrariam os conceitos básicos encontrados na maioria dos livros
This work has objective study the influence of suspension geometry on the sprung mass attitudes. It presents a confrontation among works and authors and this segmented in three parts; where in the first part the basic concepts are defined, dive, squat, lift, anti-dive, anti-squat, anti-lift and equivalent trailing-arm; in the second part the limitations are presented and the new concepts are defined for R. S. Sharp and in the third part are presented the bidimensional dynamic model introduced by Fu-Cheng Wang. It presents a virtual model in system of multi-bodies developed in the program ADAMS, with all the subsystems that composes a complete vehicle. It innovates when bringing such object to study one vehicle of competition (formula SAE) that it has a particularity suspension system push-rod. It surprises with results because it’s opposite of the basic concepts which is present in the majority of books

This work is focused on the development of a thorough study about ISO standards focused on the vehicle dynamics, standardized tests of vehicle dynamics and measured variables that allow us to describe and model the behaviour of riding vehicles properly. In the Appendix A of the thesis, there is a list of all known ISO standards dealing with given topic. The standard ISO 15037-1 Road vehicles – Vehicle dynamics test methods, Part 1: General conditions for passenger cars is described in detail, including the forms for test reports and the Appendix C and D. In the thesis, there is also described a model of minimal needed measuring system that is still in good accordance with the standard ISO 15037-1 and fulfills all its requirements. Detailed description of all used sensors that are used to measure required variables is given, as well as a short description of all sensors that are used for measurement of other variables. After that, measurement abilities of the instrumentation of measuring system RIO used in ÚADI FSI Brno is compared and confronted with requirements given by the standard, to see, if all given criteria are properly fulfilled. Because of the fact that standard-given criteria are quite mild, while the equipment of the faculty is high-level technology, mostly made directly for measuring of dynamic parameters of the vehicles, including racing vehicles, the system is in full accordance with the standard ISO 15037-1.

Except for aerodynamics forces, all vehicle excitation forces are generated at the tyre-road interface. Considering low speed applications, such as terramechanics where the aerodynamics force are negligible, the road-tyre interaction is of extreme importance. Crucial variables which govern the forces generated at the tyre-road interface are tyre side-slip angle, tyre longitudinal slip ratio and terrain pro le. Solutions to measure these variables exist for smooth hard roads but the solutions experience challenges on rough and o -road terrain. Digital Image Correlation is concerned with tracking the changes of a scene in a sequence of images or in images obtained from multiple viewpoints. These methods are frequently used in micro and nano-scale mechanical testing due to its ease of implementation and use as well as its non-contact approach. As a result these techniques are being implemented in many elds from material testing, physics, lm animations and engineering. The aim of this thesis is to investigate the applications of Digital Image Correlation in vehicle dynamics using cost e cient o -the-shelf digital cameras and lenses. The following three vehicle dynamic problems are investigated: The measurement of the vehicle side-slip angle, longitudinal slip-ratio of a pneumatic tyre and high delity terrain pro ling. The vehicle side-slip angle can be used as a measure of the vehicle stability and therefore be used to improve the e ectiveness of vehicle stability controllers. The tyre side-slip angle is also a vital measurement in characterising the lateral force characteristics of pneumatic tyres. A planar measuring method using Digital Image Correlation is shown to accurately measure the side-slip angle. The method is expanded by developing two additional algorithms which can measure all translational and rotational velocities. These methods are validated on both smooth surfaces and rough o -road terrain. A method is also implemented whereby the longitudinal slip ratio of a tyre can be measured using a single camera. Therefore, doing away with the conventional method of using three independent measurement systems. Features in the contact patch, encompassing both the tyre and the road, are tracked in a sequence of images. The features are classi ed into features lying on the tyre, road and outliers using a clustering algorithm. This enables the system to determine the tyre and road velocities from which the slip ratio is determined. High delity terrain pro ling is performed using a calibrated stereographic rig to obtain a three dimensional point cloud of the scene which is being viewed. The point cloud generated at one sample contains a grid of points encompassing a large area with points spaced both laterally and longitudinally. Overlapping point clouds are generated and joined using various registration techniques. The joined point clouds are sub-sampled to obtain a regularised grid of point containing a single point cloud of non overlapping points. The proposed techniques create new possibilities in the eld of vehicle dynamics. Enabling the side-slip angle to be measured in rough of road conditions while providing additional measurements. The longitudinal slip ratio which is measured directly at the contact patch could pave the way for better understanding the mechanism of the longitudinal tyre force generation. The inexpensive road pro ling systems enables multiple sensors to be used in terramechanics tests to determine the impact of a vehicle on the environment. The thesis presents the mere tip of the ice berg concerning digital image correlation used in vehicle dynamics with many more possibilities waiting to be discovered.
Thesis (PhD)--University of Pretoria, 2015.
tm2015
Mechanical and Aeronautical Engineering
PhD
Unrestricted

碩士
國立屏東科技大學
車輛工程系碩士班
93
The purpose of this study is to probe into joined-wing longitudinal flight characteristic and tracking control. First the study to set up longitudinal dynamic of nonlinearity of an joined-wing. The situation in long and short cycle probe into the convergence speed to the stable state and the relation function between the system parameters. The rule of controlling set up, this study joins the system dynamic observation. In order reduce the demand for sensor. The main goal of controlling the rule is thrust and elevator, in order fly follow to trajectory of airplane. However, the study use feed forward and feedback control to increase the longitudinal damping. It can obtain following the result of better then control speed and height.