Дисертації з теми "Gear Machines"
Оформте джерело за APA, MLA, Chicago, Harvard та іншими стилями
Ознайомтеся з топ-50 дисертацій для дослідження на тему "Gear Machines".
Біля кожної праці в переліку літератури доступна кнопка «Додати до бібліографії». Скористайтеся нею – і ми автоматично оформимо бібліографічне посилання на обрану працю в потрібному вам стилі цитування: APA, MLA, «Гарвард», «Чикаго», «Ванкувер» тощо.
Також ви можете завантажити повний текст наукової публікації у форматі «.pdf» та прочитати онлайн анотацію до роботи, якщо відповідні параметри наявні в метаданих.
Переглядайте дисертації для різних дисциплін та оформлюйте правильно вашу бібліографію.
Grebchenko, A. "Mechanization and automation gear milling." Thesis, Сумський державний університет, 2013. http://essuir.sumdu.edu.ua/handle/123456789/33627.
Повний текст джерелаGulati, Sidhant, Andrea Vacca, and Manuel Rigosi. "A General Method to Determine the Optimal Profile of Porting Grooves in Positive Displacement Machines: the Case of External Gear Machines." Saechsische Landesbibliothek- Staats- und Universitaetsbibliothek Dresden, 2016. http://nbn-resolving.de/urn:nbn:de:bsz:14-qucosa-199832.
Повний текст джерелаGullo, Thomas W. "A Methodology to Evaluate the Dynamic Behavior of Back-to-back Test Machines." The Ohio State University, 2019. http://rave.ohiolink.edu/etdc/view?acc_num=osu1555588592218025.
Повний текст джерелаWichert, Torsten. "Design and Construction Modifications of Switched Reluctance Machines." Doctoral thesis, Saechsische Landesbibliothek- Staats- und Universitaetsbibliothek Dresden, 2009. http://nbn-resolving.de/urn:nbn:de:bsz:14-ds-1235569858100-62518.
Повний текст джерелаWichert, Torsten. "Design and Construction Modifications of Switched Reluctance Machines." Doctoral thesis, Technische Universität Warschau, 2008. https://slub.qucosa.de/id/qucosa%3A258.
Повний текст джерелаKraicinger, Lukáš. "Software pro zpracování dat a řízení CNC obráběcího stroje." Master's thesis, Vysoké učení technické v Brně. Fakulta informačních technologií, 2017. http://www.nusl.cz/ntk/nusl-363853.
Повний текст джерелаКлочко, А. А., та Ю. А. Синица. "Улучшение рабочих характеристик среднемодульных зубчатых передач, полученных на зубофрезерном станке с числовым программным управлением". Thesis, Сумский государственный университет, 2017. http://essuir.sumdu.edu.ua/handle/123456789/61466.
Повний текст джерелаВ настоящее время актуальной является задача снижения уровня шумов зубчатых передач в связи с ужесточением и нормированием требований к уровню шумов автотракторной техники. По традиционной технологии до последнего времени практически все зубчатые колеса грузовых автомобилей, тракторов и сельхозмашин в странах СНГ изготавливались без зубошлифования. Требуемая точность зубчатых колес устанавливалась отраслевыми стандартами, которые, позволяли изготавливать зубчатые колеса на отечественном оборудовании используя инструмент отечественного производства.
Jermolajev, Štěpán. "Kontinuální odvalovací broušení čelního ozubení." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2013. http://www.nusl.cz/ntk/nusl-230504.
Повний текст джерелаHajar, Mayssaa. "Contribution of random sampling in the context of rotating machinery diagnostic." Thesis, Lyon, 2018. http://www.theses.fr/2018LYSES001/document.
Повний текст джерелаNowadays, machine monitoring and supervision became one of the most important domains of research. Many axes of exploration are involved in this domain: signal processing, machine learning and several others. Besides, industrial systems can now be remotely monitored because of the internet availability. In fact, as many other systems, machines can now be connected to any network by a specified address due to the Internet of Things (IOT) concept. However, this combination is challenging in data acquisition and storage. In 2004, the compressive sensing was introduced to provide data with low rate in order to save energy consumption within wireless sensor networks. This aspect can also be achieved using random sampling (RS). This approach is found to be advantageous in acquiring data randomly with low frequency (much lower than Nyquist rate) while guaranteeing an aliasing-free spectrum. However, this method of sampling is still not available by hardware means in markets. Thus, a comprehensive review on its concept, its impact on sampled signal and its implementation in hardware is conducted. In this thesis, a study of RS and its different modes is presented with their conditions and limitations in time domain. A detailed examination of the RS’s spectral analysis is then explained. From there, the RS features are concluded. Also, recommendations regarding the choice of the adequate mode with the convenient parameters are proposed. In addition, some spectral analysis techniques are proposed for RS signals in order to provide an enhanced spectral representation. In order to validate the properties of such sampling, simulations and practical studies are shown. The research is then concluded with an application on vibration signals acquired from bearing and gear. The obtained results are satisfying, which proves that RS is quite promising and can be taken as a solution for reducing sampling frequencies and decreasing the amount of stored data. As a conclusion, the RS is an advantageous sampling process due to its anti-aliasing property. Further studies can be done in the scope of reducing its added noise that was proven to be cyclostationary of order 1 or 2 according to the chosen parameters
Stenekap, Daniel. "Classification of Gear-shift data using machine learning." Thesis, Mälardalens högskola, Akademin för innovation, design och teknik, 2021. http://urn.kb.se/resolve?urn=urn:nbn:se:mdh:diva-53445.
Повний текст джерелаLi, Xianren. "Optimised parametric gear system design." Thesis, Sheffield Hallam University, 1994. http://shura.shu.ac.uk/19957/.
Повний текст джерелаWang, Hong. "MACHINE HEALTH MONITORING OF ROTOR-BEARING-GEAR TRANSMISSION SYSTEM." University of Akron / OhioLINK, 2005. http://rave.ohiolink.edu/etdc/view?acc_num=akron1133281063.
Повний текст джерелаEggers, Berndt Leonard. "Draglines gear monitoring under fluctuating conditions /." Pretoria : [s.n.], 2007. http://upetd.up.ac.za/thesis/available/etd-08272008-134253/.
Повний текст джерелаZhang, Yaojun. "Mathematical bases for gear inspection by 3D coordinate measuring machine." Doctoral thesis, Universite Libre de Bruxelles, 1995. http://hdl.handle.net/2013/ULB-DIPOT:oai:dipot.ulb.ac.be:2013/212619.
Повний текст джерелаEcheverria-Villagomez, Jose Salvador. "The use of tangential accelerometers in gear drives." Thesis, University of Cambridge, 1991. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.334077.
Повний текст джерелаLigata, Haris. "Impact of system-level factors on planetary gear set behavior." Columbus, Ohio : Ohio State University, 2007. http://rave.ohiolink.edu/etdc/view?acc%5Fnum=osu1172599656.
Повний текст джерелаFish, Michael Anderson. "Transmission errors in precision worm gear drives." Thesis, University of Huddersfield, 1998. http://eprints.hud.ac.uk/id/eprint/4851/.
Повний текст джерелаAlshahrany, Shaya. "Rolling contact fatigue in heavily loaded gear transmission contacts." Thesis, Cardiff University, 2015. http://orca.cf.ac.uk/90422/.
Повний текст джерелаFrith, Robert Hedley. "A model of gear pump wear due to solids contamination." Thesis, Queensland University of Technology, 1994.
Знайти повний текст джерелаHoseini, Saba. "Experimental simulation of gear hobbing through a face milling concept in CNC-machine." Thesis, KTH, Materialvetenskap, 2013. http://urn.kb.se/resolve?urn=urn:nbn:se:kth:diva-126804.
Повний текст джерелаJohnson, David Ewen. "Use of noise for the detection of gear faults in rotating machinery." Thesis, University of the West of England, Bristol, 1993. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.358312.
Повний текст джерелаLerch, Christopher Allen. "Non-invasive recovery of gear rotation from machine vibration dc by Christopher Allen Lerch." Thesis, Massachusetts Institute of Technology, 1995. http://hdl.handle.net/1721.1/35019.
Повний текст джерелаChen, Dajun. "Applications of time-scale representations and artificial neural networks in gear condition monitoring." Thesis, De Montfort University, 1998. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.391569.
Повний текст джерелаWolfer, Scott. "Design and Analysis of A General-Purpose Planetary Gear Durability Test Machie." The Ohio State University, 2005. http://rave.ohiolink.edu/etdc/view?acc_num=osu1409148817.
Повний текст джерелаLi, Zheng. "Spur gear teeth contact analysis on power-train transmission noise, vibration and harshness." Thesis, University of Warwick, 2009. http://wrap.warwick.ac.uk/3163/.
Повний текст джерелаÖsterlind, Tomas. "An Analysis of Machining System Capability and Its Link with Machined Component Quality." Licentiate thesis, KTH, Maskin- och processteknologi, 2013. http://urn.kb.se/resolve?urn=urn:nbn:se:kth:diva-122144.
Повний текст джерелаQC 20130513
Krumins, Armands. "Gearbox fault detection, based on Machine Learning of multiple sensors." Thesis, KTH, Skolan för industriell teknik och management (ITM), 2021. http://urn.kb.se/resolve?urn=urn:nbn:se:kth:diva-301603.
Повний текст джерелаLiu, Huaiju. "Lubricated contact analysis of a spur gear pair with dynamic loads." Thesis, University of Warwick, 2013. http://wrap.warwick.ac.uk/57917/.
Повний текст джерелаAli, Emad, Jürgen Weber, and Matthias Wahler. "A Machine Learning Approach for Tracking the Torque Losses in Internal Gear Pump - AC Motor Units." Saechsische Landesbibliothek- Staats- und Universitaetsbibliothek Dresden, 2016. http://nbn-resolving.de/urn:nbn:de:bsz:14-qucosa-199438.
Повний текст джерелаZorgani, Muftah Em M. "Procedure for selecting appropriate steels for machine design." Thesis, Cranfield University, 2010. http://dspace.lib.cranfield.ac.uk/handle/1826/6837.
Повний текст джерелаCavina, Eugenio. "GEAR: una piattaforma Big Data per l'elaborazione di stream di dati attraverso Machine Learning e Business Rules." Master's thesis, Alma Mater Studiorum - Università di Bologna, 2020. http://amslaurea.unibo.it/20416/.
Повний текст джерелаMasat, Mehmet. "Design And Implementation Of Hot Precision Forging Die For A Spur Gear." Master's thesis, METU, 2007. http://etd.lib.metu.edu.tr/upload/12608550/index.pdf.
Повний текст джерелаHoskins, Thomas James. "The mechanical and tribological properties of PEEK gears." Thesis, University of Birmingham, 2015. http://etheses.bham.ac.uk//id/eprint/6047/.
Повний текст джерелаWesterberg, Johan. "Utveckling och utvärdering av en rörrensningsmaskin." Thesis, KTH, Maskinkonstruktion (Inst.), 2015. http://urn.kb.se/resolve?urn=urn:nbn:se:kth:diva-183517.
Повний текст джерелаThis report will present a design study of a new development of a pipe cleaning machine, which is ordered by a company working in the plumbing industry. The design that has been developed consists of; a base structure made in plastic material, which can be mold casted in one piece, a module that places all the components inside the drum, telescopic handles which make the machine easy to store, and storage locations for additional accessories. The performance of the machine has been optimized by test studies and calculations, which has given the optimal power, weight and dimensions. The pipe cleaning machine was modeled in Solid Edge, and then imported into Ansys for further calculations. To solve problems with vibrations and heat generations along the wire, a gear was designed. This gear was later manufactured and tested to be able to verify that the described problems were solved. This part is, however, not included in this report for reasons of confidentiality.
Rapley, Steve. "Computational investigation of torque on spiral bevel gears." Thesis, University of Nottingham, 2009. http://eprints.nottingham.ac.uk/10803/.
Повний текст джерелаMolokanov, Aleksej. "Design of the high-strength gear steels for use in advanced power transmission for low-emission aero-engines." Thesis, University of Birmingham, 2017. http://etheses.bham.ac.uk//id/eprint/7729/.
Повний текст джерелаAlharbi, Khalid Abdulkhaliq M. "The mechanical contact behaviour and tribology of polymer gears." Thesis, University of Warwick, 2018. http://wrap.warwick.ac.uk/103328/.
Повний текст джерелаHaddad, Charles Daoud. "The elastic analysis of load distribution in wide-faced helical gears." Thesis, University of Newcastle upon Tyne, 1991. http://hdl.handle.net/10443/3615.
Повний текст джерелаGurkan, Niyazi Ersan. "Non-linear Mathematical Modeling Of Gear Rotor Bearing Systems Including Bearing Clearance." Master's thesis, METU, 2005. http://etd.lib.metu.edu.tr/upload/12606798/index.pdf.
Повний текст джерелаRKAN, Niyazi Ersan M.S. Department of Mechanical Engineering Supervisor: Prof. Dr. H. Nevzat Ö
ZGÜ
VEN November 2005, 130 pages In this study, a non-linear mathematical model of gear-rotor systems which consists of elastic shafts on elastic bearings with clearance and coupled by a non-linear gear mesh interface is developed. The mathematical model and the software (NLGRD 2.0) developed in a previous study is extended to include the non-linear effects due to bearing clearances by using non-linear bearing models. The model developed combines the versatility of using finite element method and the rigorous treatment of non-linear effect of backlash and bearing clearances on the dynamics of the system. The software uses the output of Load Distribution Program (LDP), which computes loaded static transmission error and mesh compliance for the contact points of a typical mesh cycle, as input. Although non-varying mesh compliance is assumed in the model, the excitation effect of time varying mesh stiffness is indirectly included through the loaded static transmission error, which is taken as a displacement input into the system. Previous computer program which was written in Fortran 77 is rewritten by using MatLAB 7.0 and named as NLGRD (Non-Linear Geared Rotor Dynamics) Version 3.0. The program is highly flexible and open to further developments. The program calculates dynamic to static load ratio, dynamic transmission error, forces and displacements at bearings. The mathematical model suggested and the code (NLGRD version 3.0) are validated by comparing the numerical results obtained from the model suggested with experimental data available in literature. The results are also compared with those of previously developed non-linear models. The effects of different system parameters such as bearing stiffness, bearing clearance and backlash on the gears are investigated. The emphasis is placed on the interaction of clearances in bearings with other system parameters.
Hulvej, Matúš. "Návrh výrobní technologie ozubeného hřídele převodovky." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2018. http://www.nusl.cz/ntk/nusl-378867.
Повний текст джерелаGovilkar, Siddhartha. "DEVELOPMENT OF A NEW TEST MACHINE FOR EXPERIMENTAL CONTACT FATIGUE INVESTIGATIONS OF SPUR GEARS." The Ohio State University, 2019. http://rave.ohiolink.edu/etdc/view?acc_num=osu1555585277243502.
Повний текст джерелаHu, Zedong. "An investigation into the wear and thermal-mechanical performance of polyacetal gears." Thesis, University of Warwick, 2017. http://wrap.warwick.ac.uk/99346/.
Повний текст джерелаKhaustov, Sergey. "Elastohydrodynamic lubrication and surface fatigue modelling of spur gears over the meshing cycle." Thesis, Cardiff University, 2016. http://orca.cf.ac.uk/95787/.
Повний текст джерелаBurns, Angela D. "Comparison of two electrofishing gears (backpack and parallel wires) and abundances of fishes of the upper Greenbrier River drainage." Morgantown, W. Va. : [West Virginia University Libraries], 2007. https://eidr.wvu.edu/etd/documentdata.eTD?documentid=5165.
Повний текст джерелаTitle from document title page. Document formatted into pages; contains vii, 65 p. : ill., maps (part col.). Includes abstract. Includes bibliographical references.
Miyasato, Hugo Heidy 1986. "Simulação do fenômeno de gear rattle em modelos de trem de potência automotivos." [s.n.], 2011. http://repositorio.unicamp.br/jspui/handle/REPOSIP/263727.
Повний текст джерелаDissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Mecânica
Made available in DSpace on 2018-08-17T18:54:27Z (GMT). No. of bitstreams: 1 Miyasato_HugoHeidy_M.pdf: 3357683 bytes, checksum: 9fcd8bd237500580084498c606879165 (MD5) Previous issue date: 2011
Resumo: Fenômenos de ruído, vibração e sua severidade (NVH) são uma grande preocupação da indústria automotiva desde o século 20. A fim de atingir uma vantagem competitiva, as montadoras têm se focado na melhora do desempenho de NVH dos seus produtos para lidar com um cenário de mercado global competitivo. No intuito de verificar o comportamento do sistema durante o processo de desenvolvimento, métodos computacionais são aplicados para encontrar melhores abordagens e na previsão de problemas, economizando tempo e orçamento da empresa gastos na construção de protótipos e testes. Nesse trabalho, gear rattle, um ruído induzido por impacto cuja causa são as engrenagens sem carga da transmissão, será modelado e simulado. É diagnosticado com maior intensidade em veículos com motores diesel em marcha lenta e excitado especificamente quando uma faixa de frequências que causa grande amplitude de vibração nos elementos internos da caixa de câmbio é alcançada. Modelos lineares do trem de potência em ponto morto ou em tração serão estudados, compreendendo as suas características básicas, tais como frequências naturais e modos associados que podem ser representativos do fenômeno. Esse sistema possui elementos com fortes não-linearidades, tais como a rigidez estratificada com histerese da embreagem e a folga entre os dentes dos engrenamentos. Uma caracterização mais realista será incluída no modelo com uma rigidez variante no tempo para o engrenamento helicoidal, utilizado em todas transmissões manuais, com uma componente dissipativa adequada aos impactos. Para verificar condições de operação que podem somente ser avaliadas segundo formulação não-linear, simulações serão realizadas para verificar a eficácia de orientações de solução e propostas de modificação encontradas na literatura
Abstract: Noise, Vibration and Harshness (NVH) phenomena are a great concern of the automotive industry since the twentieth century. In order to achieve a commercial advantage, manufacturers have focused on improving the NVH performance of their products to cope with a competitive global market scenario. To verify the behavior of the system during the design process, computational methods are applied to find a better approach and foresee problems, saving company budget and time spent in prototypes and tests. In this work, gear rattle, a impact-induced noise caused by the unloaded gear teeth inside the gearbox, will be modeled and simulated. It is diagnosed with a higher intensity in diesel vehicle engines at idle speed and in a more specific way excited when a range of frequency that causes large amplitude of vibration in the internal elements of the gearbox is reached. Linear models of the powertrain operating in idle and traction will be studied, in order to understand its basic characteristics, such as natural frequencies and associated vibration modes that could be representative to this phenomena. This system has elements with strong nonlinearities such as the stratified stiffness with hysteresis of the clutch and the backlash between the gear teeth. A more realistic feature will be included in the model with a time variable stiffness for the helical gear mesh, used in all manual transmissions, with a suitable dissipative component for the impacts. To verify operational conditions which can only be evaluated with nonlinear formulation, simulations will be made to verify the effectiveness of solution guidelines and modification procedures found in literature
Mestrado
Mecanica dos Sólidos e Projeto Mecanico
Mestre em Engenharia Mecânica
Pruša, Lubomír. "Konstrukční návrh manipulátoru obrobků." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2012. http://www.nusl.cz/ntk/nusl-230427.
Повний текст джерелаLou, Kaiyan. "Syntheses of novel antitumor 1,4-anthracenediones and functionized cyclododeciptycene based molecular gears." Diss., Manhattan, Kan. : Kansas State University, 2007. http://hdl.handle.net/2097/883.
Повний текст джерелаOzturk, Fatih Mehmet. "Optimum Design Of Multistep Spur Gearbox." Master's thesis, METU, 2005. http://etd.lib.metu.edu.tr/upload/2/12606749/index.pdf.
Повний текст джерела0.1 to ±
0.00001 on overall gear ratio) depending on the user selected constraints (unequal gear ratio for every stage, noninteger gear ratio e.g.). Dimensional design is determined by considering bending stress, pitting stress, and involute interference constraints. These steps are carried out iteratively until a desirable solution is acquired. The necessary parameters for configuration design such as number of teeth, module, addendum modification coefficient, are selected from previously determined gear pairs that satisfies the constraints by user interaction considering the performance criterion from the developed program. The positions of gears and shafts are determined automatically in order to keep the volume of gearbox as minimum while satisfying the nonlinear spatial constraints (center distance constraint for proper meshing of gear pairs, face distance constraint for proper assembly of pinion and gear having same shaft, gear interference constraint for preventing interferences between gears, shaft interference constraint for preventing interferences between gears and shafts) by using DLL (Dynamic Link Library) technology of Lingo 8.0 optimization software together with Visual Basic 6.0. If shaft interference constraint is removed then cantilevered mounting of gear pairs would also be possible, otherwise the gears should be mounted between bearings. Visual output of assembly is made by using Autodesk Inventor 7.0, automatically by the program.
Богачов, О. О. "Удосконалення технологічного процесу виготовлення вала-шестерні конічної 5206-4205.05-Б домкрата установчого шляхом підвищення стійкості різального інструменту на зубофрезерній операції". Master's thesis, Сумський державний університет, 2018. http://essuir.sumdu.edu.ua/handle/123456789/72562.
Повний текст джерелаКвалификационная работа магистра: 136 с., 27 рис., 23 табл., 60 источников. На сегодняшний день производительность механической обработки деталей машин во многом зависит от стойкости режущего инструмента. Поломки инструментов увеличивают вне цикловые затраты времени и как следствие снижают коэффициент использования оборудования. Именно поэтому появилась необходимость усовершенствования инструмента путем нанесения защитного покрытия на режущую часть инструмента. Цель работы заключается в доказательстве эффективности применения защитного покрытия. При этом должны быть решены следующие задачи как вариантный выбор способа изготовления заготовки; проектирования маршрута механической обработки; определение оптимальных режимов резания; целесообразность применения того или иного оборудования. Объектом исследования является технологический процесс изготовления детали вал-шестерня коническая. Предметом исследования являются методы повышения стойкости режущего инструмента в процессе механической обработки. Научная новизна полученных результатов - предложено применение защитного покрытия методом электроискрового легирования для повышения эффективности режущего инструмента в процессе обработки вала-шестерни конической на зубофрезерной операции. Практическое значение полученных результатов заключается в совершенствовании характеристики режущего инструмента в процессе механической обработки.
The master's qualification work: 136 pp., 27 pict., 23 tabl., 60 sources. To date, the performance of mechanical machining of machine parts largely depends on the stability of the cutting tool. Instrument breakdowns increase off-cycle time expenditures and, as a consequence, reduce the utilization rate of equipment. That is why there was a need to improve the cutting tool by applying a protective coating on the cutting part of the instrument. The purpose of the work is to prove the effectiveness of the application of protective coating. At the same time, such tasks should be solved as a variant choice of a method of manufacturing of a work-piece; design of the route of mechanical processing; determination of optimal cutting modes; expediency of the use of this or that equipment. The object of the study is the technological process of manufacturing the details of the gear-pinion cone. The subject of research is the methods of increasing the stability of the cutting tool in the process of machining. The scientific novelty of the obtained results - the application of protective coating by the method of electroscope doping has been proposed to improve the efficiency of the cutting tool in the process of processing the tapered shaft gear on the dental-mill operation. The practical value of the results obtained is to improve the characteristics of the cutting tool in the process of machining.
Геть, Юрій Михайлович, та Yuriy Het. "Обґрунтування і розробка безступінчатого приводу головного руху і механізму зміни частоти обертання шпинделя свердлильного верстату". Master's thesis, Тернопільський національний технічний університет імені Івана Пулюя, 2018. http://elartu.tntu.edu.ua/handle/lib/24144.
Повний текст джерелаThe graduation thesis deals with the scientific and technical problem involving the substantiation and development of the variable-speed drive of the principal movement and mechanism for changing the spindle rotational speed of the drilling machine. The dynamic calculation of the spindle unit was carried out, the structure of the variable-speed gear box and the acceleration head were described in this work. The investigation of the possibility for the construction on the base of vertically oriented drilling machine with variable-speed mechanical system on the basis of the implementation of mechanical variable-speed drive in kinematic chain is carried out in this work. The research and description of the machine tool structure, its design parameters are given. The construction design proved to be cost effective and reasonable. The design calculations of the certain elements of the driveline of the principal movement, particularly of the spindle unit, are performed. The design of the high-speed head improving technical capabilities of the given group is developed. The necessary technical and economic calculations proving the rationale for the given work are provided.
Вступ; Аналітичний розділ; Оптимізація схем формоутворення на проектованому верстаті і оптимізація його компонувальної схеми; Вибір та обґрунтування вихідних даних на розробку верстатного обладнання; Технологічний розрахунок; Проектування конструкції верстатного обладнання; Науково-дослiдний роздiл; Спеціальний розділ, обґрунтування економічної ефективності прийнятих рішень; Охорона праці та безпека в надзвичайних ситуаціях; Екологія; Висновки