Дисертації з теми "Electron-beam technologies"
Оформте джерело за APA, MLA, Chicago, Harvard та іншими стилями
Ознайомтеся з топ-22 дисертацій для дослідження на тему "Electron-beam technologies".
Біля кожної праці в переліку літератури доступна кнопка «Додати до бібліографії». Скористайтеся нею – і ми автоматично оформимо бібліографічне посилання на обрану працю в потрібному вам стилі цитування: APA, MLA, «Гарвард», «Чикаго», «Ванкувер» тощо.
Також ви можете завантажити повний текст наукової публікації у форматі «.pdf» та прочитати онлайн анотацію до роботи, якщо відповідні параметри наявні в метаданих.
Переглядайте дисертації для різних дисциплін та оформлюйте правильно вашу бібліографію.
Ferhati, Arben. "Single-phase laminar flow heat transfer from confined electron beam enhanced surfaces." Thesis, Brunel University, 2015. http://bura.brunel.ac.uk/handle/2438/13827.
Повний текст джерелаMorken, Michael Owen Morken. "An Investigation Into The Feasibility Of Transparent Conductive Coatings At Visimax Technologies." Case Western Reserve University School of Graduate Studies / OhioLINK, 2017. http://rave.ohiolink.edu/etdc/view?acc_num=case1496835960043161.
Повний текст джерелаZobač, Martin. "Řízení a diagnostika elektronového svazku pro pokročilé technologie." Doctoral thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2010. http://www.nusl.cz/ntk/nusl-233899.
Повний текст джерелаVacek, Petr. "Modifikace vrstev deponovaných technologiemi HVOF a cold spray pomocí technologie elektronového paprsku." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2016. http://www.nusl.cz/ntk/nusl-254211.
Повний текст джерелаMareš, Jiří. "Modifikace charakteru rozhraní substrát-nástřik vrstev deponovaných technologiemi žárového nanášení pomocí technologie elektronového paprsku." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2015. http://www.nusl.cz/ntk/nusl-231939.
Повний текст джерелаБарсук, Іван Володимирович, Иван Владимирович Барсук, Ivan Volodymyrovych Barsuk, Олександр В`ячеславович Бондар, Александр Вячеславович Бондарь, Oleksandr Viacheslavovych Bondar, Олексій Олександрович Дрозденко, et al. "Application of simulation technologies to the investigation of the beam generating systems." Thesis, Sumy State University, 2011. http://essuir.sumdu.edu.ua/handle/123456789/20807.
Повний текст джерелаТугай, Сергій Борисович. "Імпульсні режими роботи технологічних електронно-променевих гармат високовольтного тліючого розряду". Doctoral thesis, Київ, 2013. https://ela.kpi.ua/handle/123456789/6373.
Повний текст джерелаPoczklán, Ladislav. "Modifikace kvazikrystalických kompaktů SPS pomocí technologie elektronového paprsku." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2018. http://www.nusl.cz/ntk/nusl-377885.
Повний текст джерелаChlupová, Monika. "Vlastnosti nástřiku slitinou Inconel na austenitickou ocel zhotoveného technologií kinetického naprašování po přetavení elektronovým paprskem." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2020. http://www.nusl.cz/ntk/nusl-417156.
Повний текст джерелаHanáček, Josef. "Modifikace mikrostruktury hořčíkové slitiny Elektron 21 pomocí technologie elektronového paprsku." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2018. http://www.nusl.cz/ntk/nusl-377873.
Повний текст джерелаVayre, Benjamin. "Conception pour la fabrication additive, application à la technologie EBM." Thesis, Grenoble, 2014. http://www.theses.fr/2014GRENI096/document.
Повний текст джерелаNowadays, the use of Additive Manufacturing processes keeps growing in the industry. Among the numerous kinds of AM processes, metallic additive manufacturing processes, and metallic Additive Layer Manufacturing in particular, are the most interesting from a mechanical designer point of view. Several research studies have been conducted on the topic of Design For Additive Manufacturing, mostly discussing the choice of AM processes or presenting the redesign of parts. There is no specific design methodology for ALM processes that takes their specificities into account.During this PhD thesis, the changes that ALM processes bring to the design space were investigated. The designer has the opportunity to easily manufacture thin parts, complex parts, lattice structures or mechanisms that don't need any assembly. These processes also have specific manufacturing constraints compared to conventional processes. The heat dissipation is the most important factor since it can cause distortions and porosities. Powder removal, surface and geometrical quality also need to be considered during design. A specific design for additive manufacturing methodology is necessary to take these changes into account.This work focuses on the Electron Beam Manufacturing process. Experiments were conducted and analyzed to assess the manufacturability regarding the thermal phenomena (during melting), the powder removal and the quality of the parts produced by EBM. The impact of the part geometry on manufacturing duration and manufacturing cost was also established.In order to use allow designers to use these pieces of information, we suggested a designing methodology. From the requirements of the parts, one or several parts are generated by the designer or by using topological optimization tools. The orientation of the part inside the manufacturing space is set before designing a refined parametric geometry. This parametric geometry is optimized in order to meet the user requirements as well as the EBM requirements. The last step is the modification of the geometry to comply with the finishing operations (machining allowances for example) and the placement of supports, if needed. This methodology was illustrated with the redesign of two example parts and showed important mass savings from the parts (while meeting user and process requirements).The prospects discovered and highlighted during this work, some of which were preliminary investigated, are presented in a specific chapter
Bučková, Katrin. "Pokročilá technologie výroby kloubních implantátů metodou EBM." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2020. http://www.nusl.cz/ntk/nusl-433499.
Повний текст джерелаKrál, Michael. "Struktura a vlastnosti svarového spoje TiAl6V4/6061 zhotoveného technologií elektronového paprsku." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2017. http://www.nusl.cz/ntk/nusl-318832.
Повний текст джерелаByrtus, Robin. "Mechanické vlastnosti svaru titanové slitiny TiAl6V4 připraveného pomocí technologie elektronového paprsku." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2018. http://www.nusl.cz/ntk/nusl-378407.
Повний текст джерелаCének, Lukáš. "Stanovení vlastností původních a EB-modifikovaných nástřiků deponovaných technologiemi tepelného nanášení pomocí vrypové zkoušky a testování nano-indentací." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2014. http://www.nusl.cz/ntk/nusl-231364.
Повний текст джерелаMatějka, Milan. "Technologie přípravy hlubokých struktur v submikronovém rozlišení." Doctoral thesis, Vysoké učení technické v Brně. Fakulta elektrotechniky a komunikačních technologií, 2017. http://www.nusl.cz/ntk/nusl-256584.
Повний текст джерелаMilton, Samuel. "Study on the machinability and surface integrity of Ti6Al4V produced by Selective Laser Melting (SLM) and Electron Beam Melting (EBM) processes." Thesis, Tours, 2018. http://www.theses.fr/2018TOUR4011/document.
Повний текст джерелаAdditive Manufacturing (AM) techniques based on powder bed fusion like Selective Laser Melting(SLM) and Electron Beam Melting processes(EBM) are being developed to make fully functional parts mainly in aerospace and medical sectors. There are several advantages of using AM processes like design freedom, reduced process steps, minimal material usage and reduced carbon footprint while producing a component. Nevertheless, the parts are built with near net shape and then finish machined to meet the demands of surface quality and dimensional tolerance
Comyn, Rémi. "Développement de briques technologiques pour la co-intégration par l'épitaxie de transistors HEMTs AlGaN/GaN sur MOS silicium." Thesis, Université Côte d'Azur (ComUE), 2016. http://www.theses.fr/2016AZUR4098.
Повний текст джерелаThe monolithic integration of heterogeneous devices and materials such as III-N compounds with silicon (Si) CMOS technology paves the way for new circuits applications and capabilities for both technologies. However, the heteroepitaxy of such materials on Si can be challenging due to very different lattice parameters and thermal expansion coefficients. In addition, contamination issues and thermal budget constraints on CMOS technology may prevent the use of standard process parameters and require various manufacturing trade-offs. In this context, we have investigated the integration of GaN-based high electron mobility transistors (HEMTs) on Si substrates in view of the monolithic integration of GaN on CMOS circuits
Matlák, Jiří. "Povrchové zpracování vybraných ocelí pomocí elektronového svazku." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2013. http://www.nusl.cz/ntk/nusl-230798.
Повний текст джерелаAbu, Khait Yosef. "Přetavení povrchu litiny s lupínkovým grafitem a možnosti jeho legování metodou elektronového paprsku." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2018. http://www.nusl.cz/ntk/nusl-377870.
Повний текст джерелаHeinzig, André. "Entwicklung und Herstellung rekonfigurierbarer Nanodraht-Transistoren und Schaltungen." Doctoral thesis, Saechsische Landesbibliothek- Staats- und Universitaetsbibliothek Dresden, 2016. http://nbn-resolving.de/urn:nbn:de:bsz:14-qucosa-202082.
Повний текст джерелаThe enormous increase in performance of integrated circuits has been driven for more than 50 years, mainly by reducing the device dimensions. This trend cannot continue in the long term due to physical limits being reached. The scope of this thesis is the development and fabrication of novel kinds of transistors and circuits that provide higher functionality compared to the classical devices, thus introducing an alternative approach to scaling. The fabrication of Schottky barrier field effect transistors (SBFETs) based on nominally undoped grown silicon nanowires using established and developed techniques is described. Further the charge carrier injection in the fabricated metal to semiconductor interfaces is analyzed under the influence of electrical fields. Structural modifications are used to optimize the charge injection resulting in increased ambipolar currents and negligible hysteresis of the SBFETs. Moreover, a device has been developed called the reconfigurable field-effect transistor (RFET), in which the electron and hole injection can be independently controlled by up to nine orders of magnitude. This device can be reversibly configured from unipolar electron conducting (ntype) to hole conducting (p-type) by the application of a program voltage to the two individual top gate electrodes at the Schottky junctions. So the RFET merges the functionality of classical FETs into one universal device. Measurements and 3D finite element method simulations are used to analyze the electrical transport and to describe the operation principle. Systematic investigations of changes in the device structure, dimensions and material composition show enhanced characteristics in scaled and low bandgap semiconductor RFET devices. For the realization of novel circuits, a concept is described to use the enhanced functionality of the transistors in order to realize energy efficient complementary circuits (CMOS). The required equal electron and hole current densities are achieved by the modification of charge carrier tunneling due to mechanical stress and are shown for the first time ever on a transistor. An electrically symmetric RFET based on a compressive strained nanowire in <110> crystal direction and 12 nm silicon core diameter exhibits unique electrical symmetry. The circuit concept is demonstrated by the integration of two RFETs on a single nanowire, thus realizing a dopant free CMOS inverter which can be programmed flexibly. The reconfigurable NAND/NOR shows that the RFET technology can lead to a reduction of the transistor count and can increase the system functionality. Additionally, further circuit examples and the challenges of an industrial implementation of the concept are discussed.The enhanced functionality and dopant free RFET technology describes a novel approach to maintain the technological progress in electronics after the expected end of classical device scaling
Heinzig, André. "Entwicklung und Herstellung rekonfigurierbarer Nanodraht-Transistoren und Schaltungen." Doctoral thesis, 2014. https://tud.qucosa.de/id/qucosa%3A29458.
Повний текст джерелаThe enormous increase in performance of integrated circuits has been driven for more than 50 years, mainly by reducing the device dimensions. This trend cannot continue in the long term due to physical limits being reached. The scope of this thesis is the development and fabrication of novel kinds of transistors and circuits that provide higher functionality compared to the classical devices, thus introducing an alternative approach to scaling. The fabrication of Schottky barrier field effect transistors (SBFETs) based on nominally undoped grown silicon nanowires using established and developed techniques is described. Further the charge carrier injection in the fabricated metal to semiconductor interfaces is analyzed under the influence of electrical fields. Structural modifications are used to optimize the charge injection resulting in increased ambipolar currents and negligible hysteresis of the SBFETs. Moreover, a device has been developed called the reconfigurable field-effect transistor (RFET), in which the electron and hole injection can be independently controlled by up to nine orders of magnitude. This device can be reversibly configured from unipolar electron conducting (ntype) to hole conducting (p-type) by the application of a program voltage to the two individual top gate electrodes at the Schottky junctions. So the RFET merges the functionality of classical FETs into one universal device. Measurements and 3D finite element method simulations are used to analyze the electrical transport and to describe the operation principle. Systematic investigations of changes in the device structure, dimensions and material composition show enhanced characteristics in scaled and low bandgap semiconductor RFET devices. For the realization of novel circuits, a concept is described to use the enhanced functionality of the transistors in order to realize energy efficient complementary circuits (CMOS). The required equal electron and hole current densities are achieved by the modification of charge carrier tunneling due to mechanical stress and are shown for the first time ever on a transistor. An electrically symmetric RFET based on a compressive strained nanowire in <110> crystal direction and 12 nm silicon core diameter exhibits unique electrical symmetry. The circuit concept is demonstrated by the integration of two RFETs on a single nanowire, thus realizing a dopant free CMOS inverter which can be programmed flexibly. The reconfigurable NAND/NOR shows that the RFET technology can lead to a reduction of the transistor count and can increase the system functionality. Additionally, further circuit examples and the challenges of an industrial implementation of the concept are discussed.The enhanced functionality and dopant free RFET technology describes a novel approach to maintain the technological progress in electronics after the expected end of classical device scaling.:Kurzzusammenfassung Abstract 1 Einleitung 2 Nanodrähte als aktivesGebiet fürFeldeffekttransistoren 2.1 Elektrisches Potential und Ladungsträgertransport in Transistoren 2.1.1 Potentialverlauf 2.1.2 Ladungsträgerfluss und Steuerung 2.2 Der Metall-Halbleiter-Kontakt 2.2.1 Ladungsträgertransport über den Schottky-Kontakt 2.2.2 Thermionische Emission 2.2.3 Ladungsträgertunneln 2.2.4 Methoden zur Beschreibung der Gesamtinjektion 2.3 Der Schottkybarrieren-Feldeffekttransistor 2.4 Stand der Technik 2.4.1 Elektronische Bauelemente auf Basis von Nanoröhren und Nanodrähten 2.4.2 Rekonfigurierbare Transistoren und Schaltungen 2.5 Zusammenfassung 3 TechnologienzurHerstellung vonNanodraht-Transistoren 3.1 Herstellung von SB-Nanodraht-Transistoren mit Rückseitengatelektrode 3.1.1 Nanodraht-Strukturbildung durch VLS-Wachstum 3.1.2 Drahttransfer 3.1.3 Herstellung von Kontaktelektroden 3.1.4 Herstellung von Schottky-Kontakten innerhalb eines Nanodrahtes 3.2 Strukturerzeugung mittels Elektronenstrahllithographie 3.2.1 Schichtstrukturierung mittels Elektronenstrahllithographie 3.2.2 Strukturierung mittels ungerichteter Elektronenstrahllithographie 3.2.3 Justierte Strukturierung mittels Elektronenstrahllithographie 3.2.4 Justierte Strukturierung mittels feinangepasster Elektronenstrahllithographie 3.2.5 Justierte Strukturierung mittels kombinierter optischer und Elektronenstrahllithographie 3.3 Zusammenfassung 4 Realisierung und Optimierung siliziumbasierter Schottkybarrieren- Nanodraht-Transistoren 4.1 Nanodraht-Transistor mit einlegierten Silizidkontakten 4.1.1 Transistoren auf Basis von Nanodrähten in <112>-Richtung 4.1.2 Transistoren mit veränderten Abmessungen 4.2 Analyse und Optimierung der Gatepotentialverteilung im Drahtquerschnitt in Kontaktnähe 4.3 Si/SiO2 - Core/Shell Nanodrähte als Basis für elektrisch optimierte Transistoren 4.3.1 Si-Oxidation im Volumenmaterial 4.3.2 Si-Oxidation am Draht 4.3.3 Silizidierung innerhalb der Oxidhülle 4.3.4 Core/Shell-Nanodraht-Transistoren mit Rückseitengate 4.4 Analyse der Gatepotentialwirkung in Abhängigkeit des Abstands zur Barriere 4.5 Zusammenfassung 5 RFET - Der Rekonfigurierbare Feldeffekttransistor 5.1 Realisierung des RFET 5.2 Elektrische Charakteristik 5.2.1 Elektrische Beschaltung und Funktionsprinzip 5.2.2 Elektrische Messungen 5.2.3 Auswertung 5.3 Transporteigenschaften des rekonfigurierbaren Transistors 5.3.1 Tunnel- und thermionische Ströme im RFET 5.3.2 Analyse der Transportvorgänge mit Hilfe der numerischen Simulation 5.3.3 Schaltzustände des RFET 5.3.4 On-zu-Off Verhältnisse des RFET 5.3.5 Einfluss der Bandlücke auf das On- zu Off-Verhältnis 5.3.6 Abhängigkeiten von geometrischen, materialspezifischen und physikalischen Parametern 5.3.7 Skalierung des RFET 5.3.8 Längenskalierung des aktiven Gebietes 5.4 Vergleich verschiedener Konzepte zur Rekonfigurierbarkeit 5.5 Zusammenfassung 6 Schaltungen aus rekonfigurierbaren Bauelementen 6.1 Komplementäre Schaltkreise 6.1.1 Inverter 6.1.2 Universelle Gatter 6.1.3 Anforderungen an komplementäre Bauelemente 6.1.4 Individuelle Symmetrieanpassung statischer Transistoren 6.2 Rekonfigurierbare Transistoren als Bauelemente für komplementäre Elektronik 6.2.1 Analyse des RFET als komplementäres Bauelement 6.2.2 Bauelementbedingungen für eine rekonfigurierbare komplementäre Elektronik 6.3 Erzeugung eines RFETs für rekonfigurierbare komplementäre Schaltkreise 6.3.1 Möglichkeiten der Symmetrieanpassung 6.3.2 Erzeugung eines RFET mit elektrischer Symmetrie 6.3.3 Erzeugung und Aufbau des symmetrischen RFET 6.3.4 Elektrische Eigenschaften des symmetrischen RFET 6.4 Realisierung von komplementären rekonfigurierbaren Schaltungen 6.4.1 Integration identischer RFETs 6.4.2 RFET-basierter komplementärer Inverter 6.4.3 Rekonfigurierbarer CMOS-Inverter 6.4.4 PMOS/NMOS-Inverter 6.4.5 Zusammenfassung zur RFET-Inverterschaltung 6.4.6 Rekonfigurierbarer NAND/NOR-Schaltkreis 6.5 Zusammenfassung und Diskussion 7 Zusammenfassung und Ausblick 7.1 Zusammenfassung 7.2 Ausblick Anhang Symbol- und Abkürzungsverzeichnis Literaturverzeichnis Publikations- und Vortragsliste Danksagung Eidesstattliche Erklärung