Дисертації з теми "Bolt tension"
Оформте джерело за APA, MLA, Chicago, Harvard та іншими стилями
Ознайомтеся з топ-26 дисертацій для дослідження на тему "Bolt tension".
Біля кожної праці в переліку літератури доступна кнопка «Додати до бібліографії». Скористайтеся нею – і ми автоматично оформимо бібліографічне посилання на обрану працю в потрібному вам стилі цитування: APA, MLA, «Гарвард», «Чикаго», «Ванкувер» тощо.
Також ви можете завантажити повний текст наукової публікації у форматі «.pdf» та прочитати онлайн анотацію до роботи, якщо відповідні параметри наявні в метаданих.
Переглядайте дисертації для різних дисциплін та оформлюйте правильно вашу бібліографію.
Martinez, Garcia Jairo Andres. "A Novel Ultrasonic Method to Quantify Bolt Tension." Scholar Commons, 2012. http://scholarcommons.usf.edu/etd/4145.
Повний текст джерелаKara, Emre. "A Numerical Study On Block Shear Failure Of Steel Tension Members." Master's thesis, METU, 2005. http://etd.lib.metu.edu.tr/upload/12606359/index.pdf.
Повний текст джерелаPascual, Pastor Ana María. "Fire behaviour of blind-bolted connections to concrete filled tubular columns under tension." Doctoral thesis, Universitat Politècnica de València, 2015. http://hdl.handle.net/10251/53240.
Повний текст джерела[ES] Las columnas tubulares de acero rellenas de hormigón presentan múltiples ventajas en términos de capacidad de carga, estética, ejecución y resistencia al fuego, gracias a la acción combinada de acero y hormigón. El esfuerzo realizado en las últimas décadas por conocer su comportamiento frente a diferentes cargas y bajo distintos parámetros ha dado lugar a una amplia difusión de su uso entre los diseñadores. No obstante, la forma de resolver la conexión con vigas de sección en I sigue siendo un hándicap y requiere un estudio específico. Una de las soluciones más comunes y populares para conectar las vigas de acero de sección abierta (vigas I) a columnas de acero de sección abierta es la conexión con chapa de testa, que en el caso de sección hueca requiere de tornillos especiales denominados tornillos ciegos, puesto que reciben el par de apriete desde una cara de la sección. En la actualidad existen diversos sistemas de fijación que permiten este tipo de conexiones y cuya respuesta y caracterización es objeto de numerosas investigaciones. En este sentido, la definición geométrica de la unión y las propiedades de los materiales son parámetros cruciales en el rendimiento de la conexión. La presente tesis analiza el comportamiento de los tornillos ciegos en el área traccionada de conexiones de placa de testa a columnas tubulares de acero rellenas de hormigón sometidas a momentos de flexión y a elevadas temperaturas. Las prestaciones de esta solución constructiva para la unión viga-columna tubular, junto con la ausencia de datos relacionados con su comportamiento en situación de incendio la convirtió en el objetivo del trabajo. En primer lugar, la investigación aborda el problema de transferencia de calor, analizando experimental y numéricamente la distribución de temperaturas en la sección de la conexión. En esta parte del estudio se obtienen los parámetros térmicos que caracterizan la respuesta térmica de la conexión a través de la calibración de los modelos numéricos con los datos experimentales. En segundo lugar, se realiza el estudio de la capacidad de los tornillos ciegos para soportar cargas de tracción en situación de incendio, es decir, se analiza cómo cambia el comportamiento de la conexión con sus características alteradas debido a las altas temperaturas. El estudio de las propiedades del material en función de la temperatura y su efecto sobre la respuesta de la conexión constituyen una parte importante de la investigación. Además, se evalúa la influencia del hormigón y el tipo de elemento de sujeción tanto en el comportamiento mecánico como termo-mecánico de la conexión. Por último, se estudia la capacidad de las uniones para cumplir con requerimientos de exposición al fuego de 30 minutos previamente al colapso. Como resultado de este trabajo se obtuvieron modelos de elementos finitos capaces de simular la conexión térmica y termo-mecánicamente, proporcionando patrones de comportamiento de gran utilidad en el diseño de las mismas. Entre las principales conclusiones, se observó la reducción de la temperatura en los tornillos gracias al núcleo de hormigón en columnas de hormigón lleno en comparación con secciones huecas, que ya en la superficie expuesta del tornillo se cuantificaba en 100ºC menos. Por el contrario, los elementos de fijación que presentaban mayor longitud de vástago de tornillo embebida en el hormigón, no generaban un efecto significativo sobre la temperatura de la parte resistente del perno. En cuanto a la capacidad resistente frente a fuego, el núcleo de hormigón supuso una mejora en términos de rigidez y de tiempo de resistencia al fuego. Sin embargo, el fallo de los pernos en una sección próxima a la superficie expuesta redujo el efecto esperado del anclaje del tornillo, que si bien implicaba una mayor rigidez de la conexión, no parecía mejorar el tiempo de resistencia a fuego. Finalmente se planteó la necesidad de
[CAT] Els pilars tubulars d'acer omplerts de formigó (CFT) presenten molts avantatges en termes de capacitat de carrega, estètica, execució i resistència al foc, gràcies a l'acció combinada de l'acer i el formigó. L'esforç realitzat en les darreres dècades per conèixer el seu comportament enfront a diferents càrregues i sota distints paràmetres ha donat lloc a una amplia difusió del seu ús entre el dissenyadors. No obstant això, la manera de resoldre la connexió amb bigues de secció en I, continua sent un handicap i requereix d'un estudi específic. Una de les solucions més comuns i populars per a connectar les bigues d'acer de secció oberta (bigues I) a columnes d'acer de secció oberta és la connexió amb 'chapa de testa', que en el cas de la secció buida requereix de perns especials denominats perns cecs perquè es rosquen des d'una cara de la secció. En l'actualitat existeixen diversos sistemes de fixació que permeten aquest tipus de connexions, la resposta i caracterització dels quals es l'objectiu de nombroses recerques. En aquest sentit, la definició geomètrica de la unió i les propietats dels materials son paràmetres crucials en el rendiment de la connexió. Aquesta tesi analitza el comportament dels perns cecs en l'àrea traccionada de connexions de 'chapa de testa', a pilars tubulars d'acer omplerts de formigó, sotmeses a moments de flexió i a elevades temperatures. Les prestacions d'aquesta solució constructiva per a la unió biga-pilar tubular junt amb l'absència de dades relacionades amb el comportament en situació d'incendi, la van convertir en l'objectiu d'aquest treball. En primer lloc, la recerca aborda el problema de transferència de calor, analitzant tant experimental com numèricament la distribució de temperatures en la secció de la connexió. En aquesta part de l'estudi, s'obtenen el paràmetres tèrmics que caracteritzen la resposta tèrmica de la connexió mitjançant el calibratge del models numèrics amb les dades experimentals. En segon lloc, es realitza l'estudi de la capacitat dels perns cecs per a suportar càrregues de tracció en situació d'incendi, es a dir, s'analitza com canvia el comportament de la connexió amb les seues característiques alterades degut a les altes temperatures. L'estudi de les propietats del material en funció de la temperatura i el seu efecte en la resposta de la connexió formen també part de la recerca. Un contingut important d'aquest treball consisteix en determinar l'influencia del formigó i el tipus d'element de fixació tant en el comportament mecànic com termo-mecànic de la connexió. Per últim, s'estudia la capacitat de les unions per a complir amb els requeriments d'exposició al foc de 30 minuts prèviament al col·lapse. Com a resultat d'aquest treball s'obtingueren models d'elements finits amb capacitat per a simular el comportament tèrmic i termo-mecànic de la connexió, proporcionant patrons de comportament de gran utilitat en el disseny. Entre les principals conclusions, es va observar la reducció de la temperatura en els perns gràcies al nucli de formigó en pilars omplerts de formigó en comparació amb el pilars buits, on ja en la superfície esposada del cargol es quantificava en 100 ºC menys. Pel contrari, els elements de fixació que presentaven major longitud de embeguda en el formigó, no generaven un efecte significatiu en la temperatura de la part resistent del pern. En quant a la capacitat resistent davant del foc, el nucli de formigó va suposar una millora en termes de rigidesa i de temps de resistència al foc. Tanmateix, la fallada dels perns en una secció pròxima a la superfície esposada va reduir l'efecte esperat de la fixació del pern, que si be implicava una major rigidesa de la connexió, no semblava millorar el temps de resistència al foc. Finalment, es va plantejar la necessitat de aprofundir en l'anàlisi incorporant un major rang de paràmetres.
Pascual Pastor, AM. (2015). Fire behaviour of blind-bolted connections to concrete filled tubular columns under tension [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/53240
TESIS
Barnett, Tobias C. "Assessment of clamping behaviour of a newly developed blind bolt, and an investigation into its performance in the tension region of moment resisting connections using open and hollow sections." Thesis, Nottingham Trent University, 2001. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.366362.
Повний текст джерелаBarke, Derek Woolrich 1975. "An in situ test for stress corrosion damage and tension in bolts." Monash University, Dept. of Mechanical Engineering, 2002. http://arrow.monash.edu.au/hdl/1959.1/7686.
Повний текст джерелаSchnupp, Keith Otto. "Effects of Head Size on the Performance of Twist-Off Bolts." Thesis, Virginia Tech, 2003. http://hdl.handle.net/10919/43600.
Повний текст джерелаMaster of Science
MOORE, AMY M. "EVALUATION OF THE CURRENT RESISTANCE FACTORS FOR HIGH-STRENGTH BOLTS." University of Cincinnati / OhioLINK, 2007. http://rave.ohiolink.edu/etdc/view?acc_num=ucin1195432529.
Повний текст джерелаBond, Douglas Edward. "Analytical and experimental investigation of a flush moment end-plate connection with six bolts at the tension flange." Thesis, Virginia Polytechnic Institute and State University, 1989. http://hdl.handle.net/10919/76341.
Повний текст джерелаMaster of Science
Madireddy, Sandeep Reddy. "Finite Element Modeling of Transverse Post-Tensioned Joints in Accelerated Bridge Construction." DigitalCommons@USU, 2012. https://digitalcommons.usu.edu/etd/1302.
Повний текст джерелаPitrakkos, Theodoros. "The tensile stiffness of a novel anchored blind-bolt component for moment-resisting connections to concrete-filled hollow sections." Thesis, University of Nottingham, 2012. http://eprints.nottingham.ac.uk/13937/.
Повний текст джерелаRoenker, Andrew T. "Testing of Torque-and-Angle High Strength Fasteners." University of Cincinnati / OhioLINK, 2017. http://rave.ohiolink.edu/etdc/view?acc_num=ucin1490701582262578.
Повний текст джерелаFabiánová, Lucie. "Přepočet a variantní návrh nosných konstrukcí objektů administrativního centra." Master's thesis, Vysoké učení technické v Brně. Fakulta stavební, 2014. http://www.nusl.cz/ntk/nusl-226643.
Повний текст джерелаTravieso, Rodríguez José Antonio. "Estudio para la mejora del acabado superficial de superficies complejas aplicando un proceso de deformación plástica (Bruñido con Bola)." Doctoral thesis, Universitat Politècnica de Catalunya, 2010. http://hdl.handle.net/10803/6419.
Повний текст джерелаMuchos elementos mecánicos como los moldes y matrices se caracterizan por tener en su geometría varias superficies complejas. De manera general casi cada producto comercial contiene, al menos, un componente crítico hecho en un molde o una matriz. Es por esto que este problema está siendo ampliamente estudiado por los investigadores de la rama de la fabricación de piezas.
En esta tesis se estudia como mejorar el acabado superficial de geometrías complejas a través de un proceso de deformación plástica: el bruñido con bola. Este proceso puede sustituir al habitualmente utilizado en este tipo de superficies, específicamente el pulido manual. Como característica fundamental del mismo, se puede decir que es un proceso automatizado que se desarrolla en la propia máquina donde está siendo elaborada la pieza en cuestión.
Para llevar a cabo este estudio se definen tres etapas. En la primera se desarrolla, en pasos sucesivos, un modelo físico para el proceso; a través del cual se podrá describir el fenómeno que ocurre durante el bruñido con bola. El objetivo final, es saber que parámetros son necesarios definir y ajustar durante la aplicación de dicho proceso. Se parte de hacer un análisis de fuerzas sobre un elemento diferencial de área y se van incorporando al modelo, las variables que están presentes en el sistema. El resultado final es un modelo en que los valores teóricos de presión se ven afectados por la influencia de los fenómenos que están presente en el sistema analizado, como son la velocidad con la que se deforma el material y el efecto del endurecimiento que va sufriendo el mismo a medida que va desarrollándose el proceso.
Una vez obtenido el modelo se realiza la caracterización a través de ensayos del material de las piezas de trabajo para poder introducir sus propiedades en el mismo y a continuación se diseñan y realizan los experimentos necesarios para validar los resultados obtenidos.
En una segunda etapa, se adicionan al modelo físico algunas variables no consideradas explícitamente hasta el momento, como el ancho de pasada lateral de la herramienta, la estrategia de mecanizado a seguir en el proceso y la influencia sobre la fuerza de bruñido, de la presión hidráulica del sistema y la profundidad de penetración del cabezal de la herramienta. Además se ajusta el modelo para el bruñido de superficies complejas. Todo esto se lleva a cabo a través del diseño de experimentos. Los resultados obtenidos se llevan a una hoja resumen donde se puede observar lo que se esperan obtener con el proceso bajo determinadas condiciones de trabajo. Como indicadores de la bondad del modelo se miden la rugosidad superficial media Ra y la rugosidad máxima total en la longitud de evaluación Rt.
En la tercera y última etapa, se realiza un estudio sobre la dureza superficial y las tensiones residuales en el material de las piezas ensayadas, para determinar los valores añadidos que aporta el proceso.
Al finalizar se llegan a conclusiones importantes sobre el proceso de bruñido con bola estudiado y sobre el cumplimiento de los objetivos planteados en la tesis. Por otra parte se recomienda toda una serie de trabajos pendientes a los cuales se les podría dar solución en un futuro inmediato.
It is quite easy to improve the surface finish of a flat surface or a cylindrical one by using a grinding process. But achieving a good finish on a surface of complex geometry is a difficult task. And this is one of the challenges the manufacturing industry faces today.
The geometry of many mechanical parts such as moulds and dies is characterised by several complex surfaces. In general almost each trade product has at least one critical component made in a mould or die. That is why this issue has been widely studied by researchers in the manufacturing industry.
This thesis aims to research on how to improve the surface finish of complex geometry through a process of plastic deformation; the ball burnishing. This process can replace the one commonly used for this kind of surface, specially the manual polishing. The main feature is an automated process that takes place in the machine itself where the part is actually being produced.
To carry out this research three stages need to be defined. At the first one, a physical model is gradually developed for the process. This model allows to describe the phenomenon happening before the ball burnishing. It purpose is to define and to set the parameters required for implementing the process. First an analysis of forces is made on an area differential element and the system variables are then added to the model. The final outcome is a model with theoretical pressure values which are determined by the phenomena happening in the analysed system; such as the speed at which the material is deformed and the hardening effect while the process develops.
Once the model has been made, the workpiece characterisation is tested to introduce the properties into the model and after that the required tests are made to validate the results.
At a second stage following variables not openly considered up to the previous stage are added to the physical model: the side cut width of the tool, the machining strategy to be applied to the process, the influence on the burnishing strength by the hydraulic pressure system, as well as the penetration depth of the tool head. The model for burnishing of complex surfaces is also fitted. And all this is done by means of the Design of Experiments techniques (DOE). The outcome is offered on a summary sheet that shows what the process can deliver under certain conditions. As goodness indicators for the model the average surface roughness Ra and the total maximum roughness are measured in the evaluation length Rt.
At the third and final stage the surface hardness and the residual stress of the tested workpiece material are verified in order to determine the added values that the process is capable of providing.
Finally interesting conclusions are drawn about the ball burnishing process and about how to reach the goals outlined in this thesis. Furthermore a range of pending research studies still need to be done to find solutions in the near future.
RÉSUMÉ
L'amélioration de la qualité de surface d'une pièce plane ou cylindrique, peut se faire d'une manière relativement simple, utilisant pour cela un processus de rectification. Cependant obtenir un bon état superficiel sur une surface de géométrie complexe (comme les surfaces gauches), est un problème difficile à traiter et correspond à l'un des objectifs que l'industrie mécanique recherche aujourd'hui.
Beaucoup d'éléments mécaniques comme les moules et les matrices comportent dans leur géométrie plusieurs surfaces gauches. De manière générale et quelque soit le domaine concerné (automobile, aéronautique, ferroviaire, etc..) quasiment chaque produit commercial contient, au moins, un composant réalisé à partir d'un moule ou d'une matrice. C'est la raison pour laquelle ce problème est amplement étudié par les chercheurs du domaine de la fabrication mécanique.
Dans cette thèse on propose une technique d'amélioration de l'état de surface de géométries complexes à travers d'un processus de déformation plastique: le rodage par déformation plastique à l'aide d'une bille. Ce processus peut remplacer le polissage manuel, long et couteux, habituellement utilisé pour ce type de surfaces. Le rodage par bille a comme avantage principal d'être un procédé automatisé qui peut s'effectuer dans la même machine où la pièce a été élaborée (centre d'usinage à Commande Numérique CN).
Pour mener à bien cette étude, on définit trois étapes. Dans la première, on développe, par phases successives, un modèle physique pour le processus; à travers duquel on pourra décrire le phénomène qui se développe durant la déformation plastique. L'objectif final, est de savoir quels sont les paramètres prépondérants et de déterminer leur réglage durant l'opération de finition.
L'étude commence avec une analyse des efforts sur un élément différentiel d'une aire élémentaire de contact et on continue en incorporant dans le modèle, les variables présentes dans le système. Le résultat final est un modèle qui montre que les valeurs théoriques de pression sont affectées par des phénomènes présents dans le système analysé, comme : la vitesse de déformation du matériau et l'effet de durcissement superficiel et progressif pendant le processus de rodage.
Une fois le modèle obtenu, on effectue la validation à travers d'essais sur différents matériaux et pièces. Pour tenir compte des propriétés de ces matériaux, on a conçu et on a réalisé, les expériences nécessaires pour valider le modèle.
Dans une seconde étape, on rajoute au modèle physique, plusieurs variables non considérés explicitement sur le modèle initial, tels que le pas de balayage, la stratégie d'usinage à suivre durant le processus et l'influence sur l'effort de rodage de la pression hydraulique du système et de la profondeur de pénétration de l'outil. Tout ceci se réalise par la mise en place d'un plan d'expériences. Les résultats obtenus sont présentés sur une feuille résumée où l'on peut observer les performances du système, sous certaines conditions de travail. Comme indicateurs de la qualité du modèle on mesure la rugosité moyenne de la surface Ra et la rugosité maximale totale Rt.
Dans la troisième et dernière étape, on réalise une étude sur la dureté superficielle et sur les contraintes résiduelles du matériau à partir des différents échantillons pour mesurer les améliorations qu'apporte le procédé de parachèvement étudié.
La thèse se termine en proposant un certain nombre de conclusions et perspectives sur le processus de « rodage par bille » étudié et en faisant un bilan par rapport aux objectifs initiaux de la thèse. En guise de perspective, on recommande un certain nombre de pistes d'amélioration qui seront développées dans un avenir proche.
Oliveira, Jobson de Queiroz. "Propriedades estocÃsticas em variedades riemannianas." Universidade Federal do CearÃ, 2012. http://www.teses.ufc.br/tde_busca/arquivo.php?codArquivo=9163.
Повний текст джерелаConselho Nacional de Desenvolvimento CientÃfico e TecnolÃgico
Esta tese teve dois objetos de estudo: propriedades estocÃsticas em uma variedade Riemanniana, a saber, Completude EstocÃstica, Parabolicidade e propriedade Feller, e a geometria do tensor de Bakry-Emery. Na primeira parte da tese estudamos tais propriedades estocÃsticas no contexto de submersÃes Riemannianas e imersÃes isomÃtricas, tendo como ponto de partida o trabalho de Pigola e Setti [28] sobre a propriedade Feller. No nosso primeiro resultado, provamos que se uma imersÃo isomÃtrica em uma variedade Cartan-Hadamard possui vetor curvatura mÃdia com norma limitada entÃo a imersÃo à Feller. Um anÃlogo desse resultado jà era conhecido para o caso de completude estocÃstica [30]. Em seguida estabelecemos condiÃÃes necessÃrias e suficientes para que uma submersÃo seja estocasticamente completa (respec. parabÃlica), a saber, se uma submersÃo Riemanniana tem fibra mÃnima e o espaÃo total à estocasticamente completo (respec. parabÃlico) entÃo a base à estocasticamente completa (respec. parabÃlica). Reciprocamente, se a submersÃo Riemanniana tem fibra mÃnima e compacta e a base à estocasticamente completa (respec. parabÃlica) entÃo o espaÃo total à estocasticamente completo (respec. parabÃlico). Finalmente provamos que uma submersÃo Riemanniana tem fibra mÃnima e compacta entÃo o espaÃo total Âe Feller, se, e somente se, a base à Feller. Na segunda parte desta tese estudamos o tensor de Bakry-Emery Ricci, Ricf, que à uma extensÃo, no caso de variedades ponderadas, do tensor de Ricci. Estudamos a seguinte situaÃÃo: Ricci ≥ -cG, onde c à uma constante positiva e G ≥ O à uma funÃÃo suave. Esta limitaÃÃo nos permitiu obter algumas consequencias geomÃtricas e topolÃgicas, que passamos a descrever. Seja Mf uma variedade Riemanniana ponderada e po Є Mf fixado. Nosso primeiro resultado à uma estimativa superior, fora da bola geodÃsica de raio ro, para o Laplaciano ponderado da funÃÃo distÃncia r ao ponto po, mf, em termos da integral da funÃÃo G. A primeira consequÃncia dessa estimativa à uma estimativa para o volume ponderado Volf (B(R)) de uma bola geodÃsica de raio R em termos da integral da funÃÃo G. A estimativa de mf, juntamente com a hipÃtese de Æ ser radial e Әr Æ ≥ -a,a ≥ 0 (ou | Æ|≤ k) tambÃm nos permite demonstrar um teorema de comparaÃÃo entre mf e maG, Laplaciano da funÃÃo distÃncia no modelo de curvatura aG, bem como um teorema de comparaÃÃo entre o volume ponderado de uma bola geodÃsica de raio R em Mf, VolÆ(B(R)), e o volume da bola geodÃsica de raio R no modelo MaG, de curvatura aG. Utilizando uma versÃo ponderada da fÃrmula de Bochner provamos que, se Ricci ≥ Gâ entÃo Mf satisfaz o princÃpio do mÃximo de Omori-Yau, onde G à funÃÃo suave, positiva, nÃo decrescente e tal que G-1 nÃo à integrÃvel. Em particular concluÃmos que Mf à estocasticamente completa. O prÃximo resultado que obtivemos estende, para o tensor Ricf, um teorema de Myers devido a Ambrose [1]. Para tanto, uma hipÃtese sobre a funÃÃo Æ foi necessÃria. Como aplicaÃÃo, estendemos um resultado de compacidade de Ricci solitons de Fernando-Lopes e Garcia-Rio [15]. Em 1976, Yau [36] provou uma estimativa para o gradiente de uma funÃÃo u, positiva, harmÃnica em B(2R), no caso de M ser completa e Ricf ≥ -k, k ≥ 0. Tal estimativa depende apenas de R e k e foi estendida, no caso ponderado, para funÃÃes f harmÃnicas positivas, supondo Ricf ≥ -k e Ric ≥ -H, k, H ≥ 0. Bringhton [9] obteve estimativas para o gradiente de uma funÃÃo *-harmÃnica positiva utilizando somente a hipÃtese Ricf ≥ -k. As estimativas que obtivemos estendem as estimativas citas acima e, no caso em que Æ=G=0 resultam na estimativa original de Yau. Finalmente, provamos um teorema de comparaÃÃo entre o primeiro autovalor de Dirichlet da bola geodÃsica de raio R em Mf e o primeiro autovalor de Dirichlet da bola geodÃsica de raio MG. Tal resultado estende, para o caso ponderado, um resultado de Bessa e Montenegro [4].
In this thesis we studied two objects(?): properties in Riemannian manifolds, more precisely stochastic completeness, parabolicity and the Feller property and geometric properties of Bakry Emery Ricci tensor. First, we studied such stochastic properties on Riemannian and isometric immersions. The initial motivation was the work of Pigola and Setti [30] about the Feller property. In our first result, we proved that if a isometric immersion on a Cartan-Hadamard manifold has bounded mean curvature vector then the immersion is Feller. An analogous result was know for stochastic completeness. After we stabilish necessary and sufficient conditions to a Riemannian submersion be stochastically complete (parabolic). More precisely if a Riemannian submersion has minimal fiber and the total space is stochastically complete (parabolic ) then the basis is also stochastically complete ( parabolic ). Conversely, if the Riemannian submersion has compact minimal fiber and the basis is stochastically complete ( parabolic, Feller ) then the total space also is. We also proved that if a Riemannian submersion has compact minimal fiber then the total space is Feller if, and only if the the basis is Feller. In the second part we studied the Barkry Emery Ricci tensor Ricf, wich is a natural extension of the Ricci tensor in the context of weighted manifolds. We studied the following: suppose that Ricf has a lower bound âcG where G is a smooth nonnegative function and c a positive constant. Such lower bound allow us to obtain some geometric and topological consequences as we describe below. Consider Mf a weighted Riemannian manifold. The first consequence is an upper estimate, outside a geodesic ball of radius r0, for the weighted Laplacian of the Riemannian distance in terms of the function G. Let Mf be a weighted Riemannian manifold and po Є Mf fixed. Our first result is an upper bound, outside of a geodesic ball of radius R centered in po, for the weighted Laplacian os the Riemannian distance function from po in terms od the function G. The first consequence of this estimate is an estimate for the weighted volume Volf (B(R)) of a geodesic ball with radius R in terms of the integral of G. This estimate together the assumption of f be radial and Ә f ≥ - a, a≥ 0 (or | f | ≤k ) allow us to prove a comparison theorem for mf e mag, the Laplacian of distance function of the Riemannian model fo curvature aG, as such as a comparison theoremfor the weighted volume of a geodesic ball with radius R on the Riemannian model MaG, with curvature aG. Using a weighted version of the Bochner formula we proved that Ricf ≥ Gâ then Mf satisfies the Omori-Yau Maximum Principle, where G is a positive, nondecreasing smooth function, such that G-1 does not belong to L1(Mf). In particular we conclude that Mf is stochastically complete. The next result we proved extends, for the tensor Ricf, a type Myers theorem due to Ambrose [1]. For this an additional assumption on f was required. As an aplication of this result we extended a result about compacity of Ricci solitons due to Fernandez-Lopez e GarcÃa-Rio [15]. In 1976, Yau [36] proved an estimate for the gradient of a positive harmonic funcion u, defined on B(2R), when M is complete and Ric ≥ -k, k≥ 0. Such estimate depends only on R and k and was extended, to the weighted, to the case, to f-harmonic positive functions, when Ricf ≥ - k and Ric ≥ - H, k, H ≥ 0. Brighton [9] obtained estimates for the gradient of a positive f-harmonic function assuming only Ricf ≥ -k. We obtained estimates for the case Ricf ≥ -G where G is a smooth nonnegative function and when f= G = 0 we recover the original estimate of Yau. Finally we proved a comparison theorem between the first eigenvalue of the geodesic ball of radius r on Mf and the first eigenvalue of the geodesic ball of radius r of the model MG. Such result extends, to the weighted case, a result due to Bessa e Montenegro [4].
Nazaikinskii, Vladimir, Anton Savin, Bert-Wolfgang Schulze, and Boris Sternin. "Elliptic theory on manifolds with nonisolated singularities : II. Products in elliptic theory on manifolds with edges." Universität Potsdam, 2002. http://opus.kobv.de/ubp/volltexte/2008/2633/.
Повний текст джерелаJagoš, Jiří. "Pevnostní a deformační analýza parametrické řady hydraulických napínáků." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2016. http://www.nusl.cz/ntk/nusl-254392.
Повний текст джерелаKAYSER, CAROLINE ROSE. "HIGH PERFORMANCE STEEL BRIDGE GIRDERS: PERFORMANCE & DESIGN." University of Cincinnati / OhioLINK, 2006. http://rave.ohiolink.edu/etdc/view?acc_num=ucin1138240938.
Повний текст джерелаJančaříková, Marie. "Testování pryžových těsnících prvků podrobených různým vnějším vlivům." Master's thesis, Vysoké učení technické v Brně. Fakulta chemická, 2016. http://www.nusl.cz/ntk/nusl-240540.
Повний текст джерелаSahin, Serkan. "A Comparative Study Of Aisc-360 And Eurocode 3 Strength Limit States." Master's thesis, METU, 2009. http://etd.lib.metu.edu.tr/upload/12610894/index.pdf.
Повний текст джерелаdesign, fabrication and erection of steel structures can be taken place at different locations as a result of rapid globalization
owners may require the use of widely accepted steel design codes. Therefore, engineers are faced with the challenge of being competent with several design specifications for a particular material type. AISC-360 and EC3 are widely accepted steel structure design specifications that utilize limit state principles with some similarities and differences in application. Hereby a study has been undertaken to put together the nominal strength expressions presented in both AISC-360 and EC3 codes in a single document, to identify the similarities and the differences in calculated strengths and to facilitate rapid learning of either of the specifications with prior knowledge of the other. Because of the wide scope of specifications, only fundamental failure modes are considered in this thesis. Resistance equations are directly compared with each other wherever possible. For cases where the treatment of specifications is entirely different, representative members were considered for comparison purposes.
Nery, Macclarck Pessoa. "Efeito da tensão média e frequência na resistência a fadiga e corrosão-fadiga de parafusos prisioneiros de aço inoxidável AISI 304." Pós-Graduação em Ciência e Engenharia de Materiais, 2018. http://ri.ufs.br/jspui/handle/riufs/7284.
Повний текст джерелаA utilização de parafusos como elementos de união tem grande importância em situações industriais com montagens e desmontagens frequentes. No presente estudo, avaliou-se o efeito da tensão média e frequência de solicitação na fadiga de parafusos prisioneiros confeccionados a partir de barras roscadas conformadas a frio. Fabricados em aço inoxidável austenítico, AISI 304. Os parafusos foram caracterizados através de ensaio de tração, análise química, análise microestrutural, difração de raios x e dureza. Esses parafusos foram testados em dois diferentes ambientes, ao ar e em solução aquosa a 35g/L de NaCl. Os ensaios de fadiga ocorreram com carregamento médio a 40% e 60% da tensão de escoamento. Após os ensaios, o aspecto da superfície de fratura foi observado. A amplitude de tensão de fadiga se mantém inalterada em relação à tensão média nos ensaios ao ar com frequência elevada. No entanto, ensaios ao ar em baixas frequências e corrosão fadiga seguem a previsão de Goodman. Estes ensaios mostraram que a maior tensão média tende a diminuir o valor da tensão alternante resistente à corrosão-fadiga nas condições aplicadas no presente estudo. Os resultados foram comparados com os modelos teóricos de previsão da vida em fadiga e com os resultados de Burguete e Patterson (1995).
São Cristóvão, SE
Iglésias, Michele Andréa Lopes. "Resistência à tração de retentores intra-radiculares fundidos sumetidos ao acabamento após cimentação com fosfato de zinco." Universidade Federal de Uberlândia, 2007. https://repositorio.ufu.br/handle/123456789/16856.
Повний текст джерелаO acabamento da porção coronária do retentor intra-radicular fundido após cimentação constitui-se rotina na clínica odontológica. Entretanto, os efeitos da ação da ponta diamantada em alta rotação sobre o agente cimentante são pouco avaliados. Este estudo testou a hipótese de que o tempo decorrido entre a cimentação e a realização do acabamento com alta rotação tenha efeito negativo na resistência à tração dos retentores intra-radiculares fundidos. Quarenta e oito raízes bovinas foram seccionadas com 15 mm de comprimento, tratadas endodonticamente e divididas aleatoriamente em quatro grupos (n=12): n=A: não submetidos ao acabamento; n=B, C e D submetidos ao acabamento com os tempos de 15, 60 minutos e 24 horas respectivamente, após a cimentação. Os condutos foram moldados pela técnica direta para a obtenção de retentores com 11 mm de comprimento intra-radicular, fundidos em cobre-alumínio, jateados com óxido de alumínio e cimentados com fosfato de zinco. O ensaio de tração foi realizado em máquina universal (EMIC) com velocidade de 0,5mm/min para todos os grupos 24 horas após a cimentação. Os resultados foram submetidos à análise de variância e teste de Bartlet (α=1%). Não houve diferenças estatisticamente significantes na resistência à tração nos grupos controle e os grupos com acabamento após a cimentação, independente do período de espera. Dentro das limitações deste estudo concluiu-se que o acabamento com alta rotação e o tempo decorrido entre a cimentação e o ensaio não produziu efeito sobre a resistência dos retentores intra-radiculares fundidos em cobre-alumínio.
Mestre em Odontologia
Städler, Hans-Albert. "Schließringbolzen ohne Sollbruchstelle für wartungsfreie Verbindungen im Nutzfahrzeug- und Stahlbau." Doctoral thesis, Saechsische Landesbibliothek- Staats- und Universitaetsbibliothek Dresden, 2012. http://nbn-resolving.de/urn:nbn:de:bsz:14-qucosa-97647.
Повний текст джерелаTan, Weiyan. "Installation behaviour of ASTM F1852 twist-off type tension control bolts." 2004. http://link.library.utoronto.ca/eir/EIRdetail.cfm?Resources__ID=94931&T=F.
Повний текст джерелаShih, Tzu-Hsien, and 石子賢. "Effects of Different Semi-Elliptical Bolt Holes on the Stress Concentration of Tensile Wooden Members." Thesis, 2010. http://ndltd.ncl.edu.tw/handle/38273044366339721678.
Повний текст джерела國立臺灣大學
森林環境暨資源學研究所
98
Generally, the tensile strength of wood is larger than that of compression strength in longitudinal direction. Because wood tissue could be damaged by metal connector or fastener, stress concentration always occurred at wood near the interface between wood and metal. This is the reason why the tensile strength value is almost close to or even lower than compression value in structural design. In previous reviews, pioneers usually solved many problems by finite element analysis (FEA) simulation and assumed that the wood was isotropic. However, the wood is a kind of anisotropic material rather than isotropic. In fact, it is orthotropic. In this study, a software called Solid Works2008 was used to find the results by FEA. The computer simulation is a tool that an assumed force can apply on a new type of bolt connection in order to reduce stress concentration. Douglas fir (Pseudotsuga menziesii) was selected as the wood member. The material of the bolt was common steel. In this computer simulation, steel was set as an isotropic material. In Cartesian coordinate, the x-direction was assumed in longitudinal direction of the wood. The y- and z-direction represented radial and tangential directions of the wood respectively. The total length of the member is 250 mm, and the width and the thickness are 60 and 12 mm. The hole is drilled in the central. The right side of the hole is a semicircle with 9.5 mm radius a, and the left side is a semiellipse with b mm semimajor axis (or with semiminor axis, if b<a). All the initial sizes are constant, but the length of the semi axis of the semiellipse is variable, so that the definition of the axis ratio R is b/a, where a is the radius of the semicircle. R is set starting from 0.75, and each model with an increment of 0.25 for R was built and analyzed. The applied load was a concentrated force of 980.67 N(100 kgf) on the metal bolt towards the left. The right side of the member would be fixed and could not be moved and there was no deformation or displacement at the end surface. The interface between the wood and the metal bolt was set to free. There was neither glue nor adhesive between them, so there was a clearance while the deformation and displacement happened. Friction was neglected, however. Compared with simulation results, it is evident that the distribution of stress is quite different between isotropic and orthotropic member. But stress concentration still exists in both models at same locations. To enhance the utilization of wood material, the good property of tensile strength of wood should be considered. But stress concentration around the hole will reduce this property. Adjusting the ratio of the axes of R can find a way to reduce the stress concentration. One of the concentrated stresses must be increased while another must be decreased whether the ratio increases or decreases. The simulation show that a good result can be obtained when the ratio R is about 1.2 to 1.25. In the experiment, strain gauges and the universal testing machine were used. Signals were measured and converted through the written computer program. Basically, some of the results are similar with computer simulations. While the applied load is constant, the value of strain at the tensile area by the bolt hole decreases with R increasing, and the value of strain at the compression area by the bolt hole increases with R increasing. However, there were some disadvantages for mechanism such as nodes of wood, grain. And the dimension of the models was too small (limited by the testing machine) that the disadvantages appeared obviously. Because of the small dimension, the scale of strain gauges was enlarged, so that a part of the results were not so accuracy.
Fu, F., Dennis Lam, and J. Ye. "Modelling semi-rigid composite joints with precast hollowcore slabs in hogging moment region." 2008. http://hdl.handle.net/10454/5888.
Повний текст джерелаMesquita, Afonso Carlos Bonina de. "Comportamento Tridimensional de Juntas Viga I - Pilar SHS com Parafusos Hollo-bolt Sujeitas a Acções Monotónicas." Doctoral thesis, 2019. http://hdl.handle.net/10316/87438.
Повний текст джерелаNo contexto das estruturas porticadas de edifícios ou similares vêm sendo investigados elementos com secção tubular bem como dispositivos mecânicos de ligação entre vigas e pilares adaptados a tal tipo de secção no sentido da validação de regras para controlo do respectivo comportamento estrutural, atendendo à problemática subjacente à necessidade de implementação de regulamentação apropriada por instituições e organismos oficiais. Nesta Tese apresenta-se um estudo com base em experimentação, análise numérica e teórica para caracterização da resposta estrutural de juntas viga I – pilar SHS com ligações utilizando o parafuso do tipo hollo-bolt como sistema de fixação ao perfil tubular adoptado nos pilares, enquanto exemplo representativo dos diversos blind-bolt-systems. A primeira parte do programa experimental, realizado no Laboratório de Mecânica Estrutural do DEC da FCTUC, incluiu oito ensaios de arrancamento de parafusos hollo-bolt, considerando diferentes valores para o aperto e dois diâmetros comercialmente disponíveis. Com os diagramas força-deslocamento foi avaliada a rigidez axial para cada uma das situações consideradas e identificada a capacidade resistente à tracção para os referidos parafusos ensaiados directamente nos perfis tubulares através de um esquema tipo T-Stub. A segunda parte da investigação incluiu 14 ensaios correspondentes ao tipo de juntas inicialmente indicado em nós externos, de canto e internos, considerando-se protótipos à escala real sob o efeito de carga estática monotónica na(s) viga(s). Foram realizados ensaios uni- e multiplanares, tendo sido elaborados diagramas momento-rotação e determinadas as propriedades estruturais como a rigidez rotacional inicial, o momento plástico resistente e a rigidez pós-elástica para as tipologias com placa rasa e estendida, contempladas na Parte 1-8 da actual versão do Eurocódigo 3. É apresentada, também, a classificação das juntas ensaiadas quanto à rigidez e quanto à resistência à flexão no âmbito das regras estabelecidas no citado Eurocódigo. Complementarmente, foram processados três modelos de elementos finitos no software ANSYS® representando as correspondentes juntas e ligações anteriormente testadas, os quais foram elaborados e calibrados segundo as geometrias reais das secções transversais adoptadas nos protótipos ensaiados e respeitando as propriedades mecânicas referentes aos aços efectivamente utilizados nas diversas componentes das ligações em questão. As principais conclusões experimentais evidenciaram a tendência para um certo comportamento do tipo membrana para a parede do pilar tubular no caso de pequenos rácios espessura/largura, a influência dos hollo-bolts nas áreas dos furos mais traccionados do perfil tubular, a rotura das patilhas associadas ao cilindro daquele parafuso e consequente arrancamento sob esforços de tracção e corte, bem como a plastificação da face solicitada da secção SHS (tanto mais notória quanto menor a espessura), para além da flexão plástica das placas de extremidade estendidas quando inseridas em juntas com pilares de maior espessura, reflectindo, neste caso, uma relação tp/tc de 1,7. Os modelos numéricos conseguiram reproduzir as várias deformabilidades encontradas nos protótipos testados verificando-se, para muitos pontos homólogos das juntas modeladas, uma similitude de resultados comparativamente ao que havia sido registado e determinado a nível experimental, designadamente no que diz respeito a deslocamentos (verticais e horizontais) mas também em relação a tensões equivalentes/principais e ainda a extensões. O estudo teórico igualmente apresentado culminou com a proposta de dois modelos analíticos para o momento resistente plástico das referidas juntas no contexto das referências de suporte à temática das forças resistentes, bem como das normas estipuladas pelo Eurocódigo 3 e pelo CIDECT. Para o caso da rigidez rotacional inicial, foi também aplicada uma dimensão alternativa na zona traccionada do pilar para o cálculo do respectivo coeficiente de rigidez da componente proposta, cuja fórmula original de cálculo havia sido anteriormente avançada por aquela mesma associação internacional. Uma comparação entre resultados teóricos e experimentais foi, ainda, realizada através dos respectivos rácios. Tendo sido observado um efeito tridimensional em nós de canto ou internos sujeitos a carga no mesmo sentido, foi também apresentada uma proposta de correcção do momento resistente e da própria rigidez em juntas localizadas na face ortogonal à face 1 do pilar bi-articulado.
Tubular section elements as well as connection mechanical devices between beams and columns, adapted to that type of section and applied in buildings’ framed structures or similar, have been investigated in order to validate rules to control their behaviour, in compliance with the regulations issued by institutions and official organizations. This thesis presents an experimental, numerical and analytical study to characterize the structural behaviour of I beam – SHS column joints connected using hollo-bolts, a representative example of blind-bolt systems. The first part of the experimental program, carried out at FCTUC´s DEC Structural Mechanics Laboratory, included eight hollo-bolts pull-out tests, considering different values for the tightening moment and two commercial diameters. With force-displacement diagrams the axial stiffness was evaluated for each of the considered situations as well as identified the tensile strength for the bolts, directly tested on the SHS profiles through a T-Stub type scheme. The second part of the experimental investigation included 14 tests corresponding to I beam – SHS column joints at external, corner and internal node´s configuration, considering real-scale prototypes under the effect of a monotonic static load applied on the beams. Uni- and multiplanar tests were performed and the respective force-displacement and moment-rotation diagrams were obtained, as well as determined the corresponding structural properties, such as initial rotational stiffness, plastic resistant moment and post-elastic stiffness for flush and extended endplate typologies, contemplated in the current version of Part 1-8 of Eurocode 3. It was presented the classification of the tested joints regarding to stiffness and resistance to bending, within the scope of that Eurocode. Furthermore, three finite element models were processed in the ANSYS® software representing the corresponding joints and connections previously tested, which were developed and calibrated according to the actual geometries of the cross sections adopted in the tested prototypes and respecting the mechanical properties of the steels actually used in the components of that connections and joints. The main experimental results evidenced the tendency of the tubular column’s wall for a membrane type behaviour, in the case of small thickness/width ratios. The results also showed the influence of the hollo-bolts in the areas corresponding to the more tensioned holes of tubular profile, moreover the hollo-bolt legs rupture, associated to the cylinder and consequent pull-out under a tensile and shear force combination, as well as the plastification of the loaded face of the SHS section (as more remarkable as lower its thickness). In addition to experimental observations mentioned before, it was also verified the plastic bending of the extended endplates when included in joints with thicker columns (reflecting a tp/tc ratio equal to 1,7). The numerical models reproduced the different deformabilities found in the tested prototypes, and for many homologous points of the modeled joints a results’ similarity was observed compared to what had been registered and determined experimentally, not only regarding to the vertical and horizontal displacements, but also in relation to equivalent/principal stresses and strains. The theoretical study culminated with a proposal of two analytical models for the plastic moment of those joints in the context of the main supporting references of the thematic subjected to the resistant forces as included in the established rules by Eurocode 3 and CIDECT. In the case of initial rotational stiffness, an alternative dimension was also proposed in the tensioned area of the column to calculate the respective stiffness coefficient of the new component proposed, which original formula was previously advanced by that institution. A comparison between theoretical and experimental results was made through the respective ratios. Having a three-dimensional effect on corner or internal nodes subjected to loads in the same direction and sense, a proposal of correction to the resistant moment and the rotational stiffness in joints, located on the orthogonal face concerning to the face number one in the simply supported column, was also presented.