Дисертації з теми "Aluminum alloy in electrohydraulic forming"
Оформте джерело за APA, MLA, Chicago, Harvard та іншими стилями
Ознайомтеся з топ-49 дисертацій для дослідження на тему "Aluminum alloy in electrohydraulic forming".
Біля кожної праці в переліку літератури доступна кнопка «Додати до бібліографії». Скористайтеся нею – і ми автоматично оформимо бібліографічне посилання на обрану працю в потрібному вам стилі цитування: APA, MLA, «Гарвард», «Чикаго», «Ванкувер» тощо.
Також ви можете завантажити повний текст наукової публікації у форматі «.pdf» та прочитати онлайн анотацію до роботи, якщо відповідні параметри наявні в метаданих.
Переглядайте дисертації для різних дисциплін та оформлюйте правильно вашу бібліографію.
Yang, Haoliang. "Creep age forming investigation on aluminum alloy 2219 and related studies." Thesis, Imperial College London, 2013. http://hdl.handle.net/10044/1/39352.
Повний текст джерелаNguyen, Vu Thua 1965. "Prediction of spring-back in thin sheet of aluminium alloy." Monash University, School of Physics and Materials Engineering, 2003. http://arrow.monash.edu.au/hdl/1959.1/5855.
Повний текст джерелаImbert, Boyd Jose. "Increased Formability and the Effects of the Tool/Sheet Interaction in Electromagnetic Forming of Aluminum Alloy Sheet." Thesis, University of Waterloo, 2005. http://hdl.handle.net/10012/857.
Повний текст джерелаSutton, Scott Christopher. "Characterization and Modeling of Lightweight Alloys in the Warm Forming Regime." The Ohio State University, 2018. http://rave.ohiolink.edu/etdc/view?acc_num=osu1524129785253984.
Повний текст джерелаShah, Manan Kanti. "Material Characterization and Forming of Light Weight Alloys at Elevated Temperature." The Ohio State University, 2011. http://rave.ohiolink.edu/etdc/view?acc_num=osu1306939665.
Повний текст джерелаAlves, José Augusto Camargo. "Estudo da conformabilidade de abas convexas da liga de alumínio AA2024-O no processo de hidroconformação de chapas." [s.n.], 2011. http://repositorio.unicamp.br/jspui/handle/REPOSIP/264433.
Повний текст джерелаDissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Mecânica
Made available in DSpace on 2018-08-19T02:21:16Z (GMT). No. of bitstreams: 1 Alves_JoseAugustoCamargo_M.pdf: 12204746 bytes, checksum: 78b1a8db87093cdc58baaa854932096e (MD5) Previous issue date: 2011
Resumo: O processo sheet hydroform, ou hidroconformação de chapas, é realizado por meio de uma prensa composta por uma membrana de borracha, preenchido com um fluido hidráulico cuja função é atuar como uma matriz, exercendo esforços sobre uma chapa de metal (blank), que é então empurrada contra um punção rígido, fazendo-o adquirir o formato deste. Embora este processo seja amplamente utilizado para a produção de pequenos lotes de peças metálicas de formato complexo e de espessura reduzida, ele exige habilidades de quem o define, pois se por um lado pode ser visto como simples por empregar apenas um molde maciço, por outro, a ausência de um sistema macho-fêmea capaz de garantir um completo travamento do blank pode ser encarado como um problema por permitir movimentos indesejados do material, que muitas vezes resultam na formação de rugas ou outros defeitos. Baseando-se nesses conceitos, o propósito deste trabalho foi o de mapear, por meio de simulações e ensaios práticos, a conformabilidade de abas convexas da liga de alumínio AA2024-0 de quatro espessuras quando submetidas a diferentes combinações de raio de curvatura e comprimento de aba. Deste modo, foi possível definir quais combinações destes parâmetros possibilitam a obtenção de componentes conformados adequadamente, isentos de rugas e outros defeitos macroscópicos, e ainda, quais condições levam à formação de irregularidades na aba conformada acima do limite preestabelecido, exigindo o emprego de prensa-chapas especiais, também conhecidos como dams, capazes de evitar a ocorrência de tais desvios. Com base nos resultados obtidos pode-se constatar que a ocorrência de rugas está associada principalmente à altura da aba conformada e não se altera significativamente quando a espessura do blank é modificada. Além disso, foi possível notar que raios de curvaturas maiores proporcionam menores valores de deformação compressiva na região conformada, permitindo obter abas mais altas e sem rugas
Abstract: Hydroform, or sheet metal fluid forming, is performed using a fluid cell press, in which the hydraulic fluid acts on the metallic blank pushing it against the male tool, acquiring its geometry. It is widely employed to manufacture small batches of complex and low thick components. If by one point of view it can be seen as simple, involving just a single rigid block as tool, by the other hand the absence of a rigid punch in certain cases can be a limitation, since it may allow the blank to move incorrectly during the process, causing wrinkles or other macro defects. Based on this limitation, the aim of this study was to define, using computational simulations and practical tests, the shrink flange formability limit of four different thickness aluminum alloy sheets when submitted to different combinations of curvature radius and flange length. As result, it could be seen which combinations can lead the material to be formed properly and which may cause failures, requiring special blank holders, known as dams, to avoid this problems. Based on the results, it can be verified that wrinkles nucleation is mainly associated with flange height and it does not change significantly when using blanks with different thicknesses. Furthermore, it could be noted that bigger curvature radius implies in smaller compressive strain on formed region, allowing to obtain higher flanges without wrinkles in these conditions
Mestrado
Materiais e Processos de Fabricação
Mestre em Engenharia Mecânica
Otomar, Heber Pires. "Estudo comparativo da estampabilidade da liga de aluminio AA1050 partindo de placas obtidas por vazamento direto e bobinas obtidas por vazamento contínuo." Universidade de São Paulo, 2010. http://www.teses.usp.br/teses/disponiveis/3/3133/tde-12082010-172944/.
Повний текст джерелаStampability of aluminum alloys is a subject of interest to several industrial sectors because they are largely used in the fabrication of several parts and components. The choice is based upon the stampability and the relative manufacturing capability in relation to other aluminum alloys that contain larger amounts of alloying elements and, consequently, higher mechanical properties. When comparing two solidification processes, namely the direct chill (DC) and the continuous casting (CC) via caster, the CC process historically presents inferior performance for the more critical stampings in these alloys. This study aims at the evaluation of the differences between the fabrication processes (routes) of AA1050 rolled to 1,80mm sheets in the conditions as annealed, rolled and after heat treatment and to characterize their microstructure and texture. Stamping tests have been performed to identify which process presents best stamping performance. To carry out these studies three production lots from the Companhia Brasileira de Alumínio CBA have been employed namely one from the DC method and two other lots from the DC method, one with and one without an intermediate homogenization treatment. All materials have been processed in rolling mills and ovens in an industrial scale. The metallurgical structure has been characterized by optical and electronic microscopy throughout the processes analyzing the intermetallics and precipitate distribution. Tensile tests have been perfumed to identify the evolution of the mechanical properties throughout the process. In the final condition, i.e., after rolling down to 1,80mm and annealing, earing tests, Erichsen drawing tests and anisotropy have been evaluated together with the Forming Limit Diagram( FLD), to evaluate which process presented the best results in terms of formability. In order to understand the changes that occurred, the macrotexture has been studied along the thickness of the rolled sheets. In the final condition, the microtexture of the DC and the CC without homogenization have been compared. Different microstructures have been obtained for the studied processes: the DC material was more homogeneous, both in terms of intemetallic distribution and grain size. The mechanical properties of the CC material, in terms of TS, YS and hardness, were sligthly higher than those for the DC material. Erichsen test showed that the DC material takes higher deformations. Earing tests showed that the CC material without homogeneization presented the best results however the DC material presented better cup height. The textures analyzed for the different process stages were mainly of the Goss , Cube and rotated Cube types. Also some typical shear textures of the Dillamore {4 4 11} and Taylor {11 11 8} types have been observed in cold rolled sheets. The S~ type, which is favourable for the formability of FCC metals, showed up in the final processing stages. The FLD showed that the CC with homogenization presented better results when compared to the other two processing routes. The stamping tests showed that the DC material presents higher drawability while the CC material without homogenization presents lower earing index.
ZAHEER, Omer. "RESHAPING AS NOVEL CIRCULAR ECONOMY STRATEGY FOR SHEET METAL BASED END-OF-LIFE COMPONENTS." Doctoral thesis, Università degli Studi di Palermo, 2022. http://hdl.handle.net/10447/533264.
Повний текст джерелаSiqueira, Gonçalo. "Caracterização microestrutural, mecânica e tratamento térmico da liga AA-6082 obtida pelo processo de conformação por spray." Universidade de São Paulo, 2010. http://www.teses.usp.br/teses/disponiveis/85/85134/tde-16012013-093254/.
Повний текст джерелаThe spray forming technology combines in a single step the advantages of the rapid solidification techniques and high the productivity of the conventional casting processes, allowing obtention of preforms with a refined microstructure, almost without porosity and macrosegregation free. The development and research efforts are leading to interesting alloys and materials production. The rapid solidification processes inherent to the spray forming allow the production of alloys with different compositions from those obtained by conventional ingot processes. The aim of this work was to carry out mechanical properties characterization of a spray formed AA-6082 alloy. The hardness results are presented in different sections related to the height of the spray formed preform (in a three-dimensional arrangement). The material was evaluated in the as sprayed condition and after heat treatment of solution at 525 ºC for 1 h, and aging for 1 h, 10 h, 100 h and 500 h periods. It was shown that the spray formed AA-6082 aluminum alloy is very stable regarding hardness variation during aging.
Otani, Lucas Barcelos. "Solidificação da liga de alumínio 319 conformada por spray." Universidade Federal de São Carlos, 2017. https://repositorio.ufscar.br/handle/ufscar/8903.
Повний текст джерелаApproved for entry into archive by Ronildo Prado (ronisp@ufscar.br) on 2017-07-03T18:18:29Z (GMT) No. of bitstreams: 1 DissLBO.pdf: 5087062 bytes, checksum: ed0430974a336dc3223e730ae90cc724 (MD5)
Approved for entry into archive by Ronildo Prado (ronisp@ufscar.br) on 2017-07-03T18:18:35Z (GMT) No. of bitstreams: 1 DissLBO.pdf: 5087062 bytes, checksum: ed0430974a336dc3223e730ae90cc724 (MD5)
Made available in DSpace on 2017-07-03T18:18:45Z (GMT). No. of bitstreams: 1 DissLBO.pdf: 5087062 bytes, checksum: ed0430974a336dc3223e730ae90cc724 (MD5) Previous issue date: 2017-03-03
Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)
The main application of 319 aluminum alloy is for manufacturing components for automobile industry. One of the main concerns related to the recycling of this metal is regarding the incorporation of impurities as iron, for instance. Due to its low solubility in solid aluminum, the presence of this element leads to the formation of intermetallic compounds such as α-Al8Fe2Si and β-Al9Fe2Si2, the most common iron phases in Si-containing Al-alloys. The β phase is harmful to mechanical properties because of its platelet like morphology. Spray forming is an advanced processing technique which can mitigate the deleterious effect of these intermetallic phases. However, the solidification process of spray formed metals is still an open discussion. In these sense, the aim of this work is to contribute to a better understanding of the solidification process of spray formed 319 aluminum alloy. The work was divided in three stages: the first evaluated the presence and morphology of intermetallic phases by varying the pouring temperature and Fe content (0.6 and 1.2 in mass percent); the second evaluated the eutectic Al-Si morphology through varying the processing conditions; and finally, the third evaluated the solute distribution in the final microstructure, in this case other aluminum alloys were studied together with the 319 (2024 and 7050). The basis for discussion the phenomena was a solidification model for spray formed metals recently proposed in the literature, which defines the process in two stages, being the final solidification occurring at low cooling rate. The results showed that by controlling the processing parameters it is possible to mitigate the β-Al9Fe2Si2 formation, as well as to alter the eutectic Al-Si morphology. The third stage indicated the possibility of maintenance of certain solute in solid solution on the periphery of aluminum grains. It could be concluded that the solidification model was adequate to explain the phenomena presented in this work.
A liga de alumínio 319 possui como aplicação a fabricação de componentes da indústria automobilística. Um dos principais problemas relacionados à reciclagem destas ligas é a incorporação de impurezas como o ferro. Devido à baixa solubilidade deste elemento, sua presença leva a formação de compostos intermetálicos, sendo o α-Al8Fe2Si e o β-Al9Fe2Si2 os mais comuns em sistemas com silício. A fase β é a mais danosa às propriedades mecânicas devido à sua morfologia de placas, sendo que uma rota de processamento que se mostra viável no sentido de mitigação do efeito deletério deste intermetálico é a conformação por spray. Apesar disso, o processo de solidificação desta técnica ainda é um assunto debatido na comunidade científica. Neste contexto, este trabalho possui o objetivo de contribuir para um melhor entendimento sobre o processo de solidificação da liga de alumínio 319 conformada por spray. O trabalho foi dividido em três etapas: a primeira avaliou a presença dos intermetálicos de ferro variando-se a temperatura de vazamento e o teor de ferro (0,6% e 1,2% em peso); a segunda avaliou a morfologia do eutético Al-Si através das alterações das condições de spray; e, por fim, a terceira avaliou a distribuição de soluto na microestrutura, neste caso, outras ligas de alumínio foram estudadas (2024 e 7050). A discussão dos fenômenos foi realizada a partir de um modelo de solidificação para materiais conformados por spray que divide o processo em duas etapas distintas, sendo a solidificação final ocorrendo a uma taxa de resfriamento relativamente lenta. Os resultados mostraram que através do controle das condições de spray é possível mitigar a formação do intermetálico β-Al9Fe2Si2, assim como alterar a morfologia do eutético Al-Si. A terceira etapa indicou a manutenção de certos elementos em solução sólida em regiões adjacentes aos contornos de grão. Pôde-se concluir que o modelo de solidificação utilizado foi adequado para explicar os fenômenos descritos nas etapas realizadas.
CNPq: 135810/2015-9
Plundrák, David. "Analýza příčin vzniku trhlin v ráfcích kol." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2013. http://www.nusl.cz/ntk/nusl-230459.
Повний текст джерелаŠíma, Vojtěch. "Výroba sendvičové závitové vložky objemovým tvářením." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2019. http://www.nusl.cz/ntk/nusl-399339.
Повний текст джерелаLätzer, Michael. "Füge- und Übertragungsverhalten torsionsbelasteter Stahl-Aluminium-Rändelpressverbindungen." Doctoral thesis, Universitätsbibliothek Chemnitz, 2016. http://nbn-resolving.de/urn:nbn:de:bsz:ch1-qucosa-200348.
Повний текст джерелаThe present thesis provides analytical, numerical and experimental fundamental studies for the joining behaviour and the transmission behaviour of a friction and form closure steel-aluminum knurled interference fit. The special feature of this connection is a knurled and oversize hard steel shaft, longitudinally pressed in a soft aluminum hub with a circular bore. The most important parameter for the joining process is the shaft chamfer angle φ. Due to the shaft chamfer angle φ the material of the hub will be formed or cutted during the joining process. By using the relative strength, the quotient of push out force and joining force who describes the joint strength, a first quality parameter for a precise selection of steel-aluminum knurled interference fit has been derived. The description of the experimentally determined torque - twisting angle – curves has shown areas of design criterion and mechanical breakdown. The maximum transmittable torque is achieved by reaching the shearing stress of the knurls in the hub - mechanical breakdown τ S. Similar to the joining and the push out behaviour, the positive influence of the shaft chamfer angle φ is also shown at the transmittable torque. Furthermore, knurled interference fits joined by forming can transmit higher torques of about 40% than interference fits joined by cutting due to the material hardening. The mechanical-physical model for calculating the static transmittable torque is based on the serration connection. Thus, the torque at the design criterion and the maximum transmittable torque at the mechanical breakdown can be found. The consideration of the forming or cutting joining process is described as a function of the shaft chamfer angle φ using the so-called angle-based plastic strain ε plRPV
Lätzer, Michael. "Füge- und Übertragungsverhalten torsionsbelasteter Stahl-Aluminium-Rändelpressverbindungen." Doctoral thesis, Universitätsverlag der Technischen Universität Chemnitz, 2015. https://monarch.qucosa.de/id/qucosa%3A20428.
Повний текст джерелаThe present thesis provides analytical, numerical and experimental fundamental studies for the joining behaviour and the transmission behaviour of a friction and form closure steel-aluminum knurled interference fit. The special feature of this connection is a knurled and oversize hard steel shaft, longitudinally pressed in a soft aluminum hub with a circular bore. The most important parameter for the joining process is the shaft chamfer angle φ. Due to the shaft chamfer angle φ the material of the hub will be formed or cutted during the joining process. By using the relative strength, the quotient of push out force and joining force who describes the joint strength, a first quality parameter for a precise selection of steel-aluminum knurled interference fit has been derived. The description of the experimentally determined torque - twisting angle – curves has shown areas of design criterion and mechanical breakdown. The maximum transmittable torque is achieved by reaching the shearing stress of the knurls in the hub - mechanical breakdown τ S. Similar to the joining and the push out behaviour, the positive influence of the shaft chamfer angle φ is also shown at the transmittable torque. Furthermore, knurled interference fits joined by forming can transmit higher torques of about 40% than interference fits joined by cutting due to the material hardening. The mechanical-physical model for calculating the static transmittable torque is based on the serration connection. Thus, the torque at the design criterion and the maximum transmittable torque at the mechanical breakdown can be found. The consideration of the forming or cutting joining process is described as a function of the shaft chamfer angle φ using the so-called angle-based plastic strain ε plRPV.
恵子, 名取, та Keiko Natori. "微細複合組織金属の変形機構および塑性加工性に関する研究". Thesis, https://doors.doshisha.ac.jp/opac/opac_link/bibid/BB12867122/?lang=0, 2014. https://doors.doshisha.ac.jp/opac/opac_link/bibid/BB12867122/?lang=0.
Повний текст джерела博士(工学)
Doctor of Philosophy in Engineering
同志社大学
Doshisha University
Imbert, Boyd Jose Miguel Segundo. "Hybrid Electromagnetic Forming of Aluminum Alloy Sheet." Thesis, 2010. http://hdl.handle.net/10012/5517.
Повний текст джерелаHung, Jung-Chung, and 洪榮崇. "Frictional Effect on Ultrasonic-Vibration Forming of Aluminum Alloy." Thesis, 2006. http://ndltd.ncl.edu.tw/handle/43228314505357372958.
Повний текст джерела國立交通大學
機械工程系所
94
The purpose of this dissertation is to investigate the frictional effect of ultrasonic-vibration during forming of aluminum alloy. This study analyses ultrasonic-vibration drawing and ultrasonic-vibration upsetting, which are extreme cases to each other in terms of relative speed between die and workpiece, to explore the frictional effect of superimposing ultrasonic-vibration during forming processes. The study focuses on four subjects: the set up of an ultrasonic vibration hot upsetting system, the influence of ultrasonic-vibration on hot upsetting, the frictional effect of ultrasonic -vibration during upsetting, and the experiment and simulation of ultrasonic-vibration drawing. In this study, a cooling mechanism was used on an ultrasonic vibration hot upsetting system to overcome high-temperature forming difficulty at the beginning. The effects of ultrasonic-vibration on the upsetting of aluminum alloy was then explored using this system. Results show that the ultrasonic-vibration can significantly reduce the compression force during hot upsetting and the reducing effect of compression force decreases while the temperature increases. Furthermore, upsetting process was used to explore the frictional effect by superimposing an ultrasonic-vibration parallel to the direction of forming. Experimental results of extrapolated compression test also indicate that ultrasonic-vibration can reduce the compressive force when friction is eliminated. The consecutive results of the hot ring compression test and temperature measurements during ultrasonic-vibration on upsetting reveal that increasing temperature by ultrasonic–vibration may reduce the flow stress and increase the interfacial friction. Finally, The ultrasonic-vibration drawing experiments and finite element analysis were performed for CD, AUD and RUD to explore the relative speed effect of workpiece and die by superimposing ultrasonic-vibration parallel as well as perpendicular to the relative speed. For both AUD and RUD, the drawing force fluctuated with the die vibration when drawing speed was below the critical drawing speed and the fluctuation amplitude tended to increase with the decrease of drawing speed. When drawing speed reaches a critical value, the fluctuation of drawing force disappears. On the other hand, results reveal that the critical drawing speed of RUD is higher than AUD and the frictional effect of ultrasonic-vibration vanishes when the interfacial gap speed is zero. From above studies we may conclude that the frictional effect induced by ultrasonic-vibration should associate with both the effect of interfacial gap variation and the temperature increase in general forming processes. The weighting of these two effects depends on the type of forming process. Following this qualitative study, quantitative analysis on the frictional effects of ultrasonic-vibration will be proceeded in the future to be applied in practical forming processes.
邱六舍. "Superplastic forming and diffusion bonding of 7475 aluminum alloy." Thesis, 1994. http://ndltd.ncl.edu.tw/handle/23217612922964165003.
Повний текст джерелаLIN, JEN-HAO, and 林仁豪. "Stamping Assisted Quick Plastic Forming of AA5083-O Aluminum Alloy." Thesis, 2019. http://ndltd.ncl.edu.tw/handle/swcyn8.
Повний текст джерела國立中央大學
機械工程學系
107
In general, the conventional superplastic molding process, because the molding takes too long, leads to non-economic benefits, and in order to find a better process method to solve this problem, this paper proposes for Quick Plastic Forming (Quick Plastic Forming, QPF) 's process, coupled with the idea of pre-punching-assisted preforming for metal phone casing molding, is expected to shorten the time required for this process and break through to become a more economical process. This study uses general commercial AA5083 -O Aluminum quick phone shell molding blown to blown molded plastic Fast explore, compare and analyzethe pre-stamped added auxiliary blowing plus pre-press and generally no faster assisted molding process capability, making phone analyzes whether more on the edge of the shell. The results of the study show that there is a rapid plastic forming using pre-punching, because a shape close to the finished product has been pre-punched, and then blown, which saves the time required and does not require a stepped blowing pressure. Blowing out the finished product we need is more time-optimized than the fast plastic molding without pre-punching aid.
Fang-WeiLuo and 羅方韋. "Prediction of High-strain-rate Forming Limit of Aluminum Alloy under Electromagnetic Forming Process." Thesis, 2010. http://ndltd.ncl.edu.tw/handle/50246079598292443835.
Повний текст джерела國立成功大學
機械工程學系碩博士班
98
A great deal of effort has been made on investigating fracture behaviors of metal sheets. With knowing the fracture behaviors, engineers are able to predict the occurrence of fracture and to prevent the sheet from fracture. With the development of high speed forming, formability theory and Cockcroft-Latham (CL) fracture criterion, which have been developed in quasi-static state, have been applied to predict fracture at high strain rate up to 1000 (1/s). In this work, the EMF experiment, which can deform a sheet at high strain-rates, was used for investigating the forming limit. The EMF experiment was performed by electromagnetically launching an aluminum alloy Al5052-H32 sheet of 0.5 mm thickness at a punch with a flat spiral electromagnetic coil. The punch was impacted by the sheets of different shapes in order to obtain forming limits at different strain paths. On the other hand, the punch radius was varied to generate various strain values of the sheet. Then, with the help of iteration analysis, the iterated effective stress – effective strain curve (ESESC) of the sheet was obtained. The obtained ESESC can be used to construct Johnson-Cook flow stress model. To predict the forming limit at high strain-rates, Cockcroft-Latham criterion was constructed using the obtained flow stress model. The results of simulation and fracture prediction at high strain-rates were both compared with the experimental results. The proposed experimental design was confirmed to be suitable for constructing the forming limit data of sheet at high strain rate up to 5000 (1/s).
Lee, John Thomas. "Simulation and experimental investigation of hot forming of aluminum alloy AA5182 with application towards warm forming." Thesis, 2012. http://hdl.handle.net/2152/ETD-UT-2012-05-5743.
Повний текст джерелаtext
Lin, Che-sheng, and 林哲聖. "A Study of Press Forming Properties of Multi-Layers Aluminum Alloy." Thesis, 2017. http://ndltd.ncl.edu.tw/handle/x63nc2.
Повний текст джерела中州科技大學
機械與自動化工程系
105
In this experiment, the 3003-4343 aluminum alloy clad plate as the mainmaterial used mainly in the industry, pressing it to nature to do research, toSolidWorks, AutoCad of stamping die for accuracy, size mould. Optimization design, in order to reduce production costs for materials and achieving economic production, increase industrial competitiveness, this experiment through to the software design of mold, take this understanding material the size of the essence for compaction.Degrees the influence of small amounts of products, production can provide the industry in the future, material selection of reference. In this experiment, mainly to discuss an extension of the material properties, and its mechanical properties of material, combined with appropriate design for mold development. The first project must be used for cutting materials like engineering, which are equipped with forming the second. First of all will be The shear on the edge in materials processing, and after commenced through the theoretical formula to calculate the size, and to 45 tons of single axis (see adobe) or rammed the workpiece the completion, forming machine for stamping process, using Vernier Caliper with to do the work of height and made measurement and analysis and numerical method, using 2 D video and statistics, measurement instrument section to confirm for speed, to understand the pressure washed and cut section of the situation and feet to make their products can be accurate.Dimension accuracy requirement. and geometric shapes. Based on the results of comprehensive experiment and observation, combined with the theory and knowledge of materials, the processing conditions of economic benefit and suitable materials are designed.
Chuen-Jiunn, Shyu, and 徐春濬. "Study on the Superplastic Forming of 8090 and 7475 Aluminum Alloy." Thesis, 1993. http://ndltd.ncl.edu.tw/handle/46597670493859187375.
Повний текст джерелаWang, Yu-Ying, and 王友穎. "Age-Forming of Aluminum Alloy Panel Containing Ribs in an Autoclave." Thesis, 2003. http://ndltd.ncl.edu.tw/handle/81330364003282463318.
Повний текст джерела逢甲大學
機械工程學所
91
The traditional method of assembling big-size aircraft-wing specimens is to rivet wing skins, ribs, and spars after separately metal forming the skins and ribs. However, this manufacturing processing suffers time-consuming, residual stresses, fits problem and probability of damage. After the progress of computer-aided design technology, the light-weigh structure with high-stiffness can be obtained. Based on the precision predict of computer-aided analysis, some traditional manufacturing methods may be abruptly changed. The purpose of this thesis is to study the aging forming of an-isogrid panel. Age forming is a metal forming method that utilizes the metallurgical stress relaxation phenomenon that occurs during the artificial aging (heat treating) of metal. The study involves the computer-aided simulation on the determination of the contoured forming surface of the female forming tools and required pressures (the loading). The finite element based software ABAQUS is employed for the plastic forming simulation. The simulation also checks the probable local fracture of the ribs. Then, utilizing the thermal aging stress relaxation phenomenon, the milling panel with female forming tools are sealed by a vacuum bag and puts inside the autoclave for metal forming and heat treatment. The quantities of the springback of the panel after the release of pressure loading and heat treating are calculated. The influences of springback of the panel under different aging cycle conditions on the autoclave are also compared.
Zhao, Chi-Hao, and 趙祈豪. "The Research on Quick Gas Forming in Precision of Aluminum Alloy." Thesis, 2018. http://ndltd.ncl.edu.tw/handle/z4en7r.
Повний текст джерела國立中央大學
機械工程學系
106
This study uses a vernier caliper to measure the metal mobile phone back shell, and uses different measurement methods to measure the data, using quality management to assess the process capability is very important three indicators, namely the value of Ck (Capability of Accuracy), Cp value (Capability of Precision) and Cpk value (Capability of Process), Ck represents the accuracy of the process, Cp represents the precision of the process, and Cpk is the comprehensive process capability index. Through the above indicators to find out the standard deviation of the process, to analyze the practicality of this process, and as a reference for subsequent development.
Yang, Yi-lang, and 楊益郎. "Friction and Lubrication Effect in Rapid Forming of Superplastic Aluminum Alloy 5083." Thesis, 2001. http://ndltd.ncl.edu.tw/handle/64354997310633505818.
Повний текст джерелаLiu, Zong-Yu, and 劉宗諭. "The Effects of High Temperature Oxidation on 8090 Aluminum Alloy Superplastic Forming." Thesis, 2014. http://ndltd.ncl.edu.tw/handle/39828596582801889271.
Повний текст джерела國立雲林科技大學
機械工程系
103
In this study, 8090 aluminum alloy set as research material to explore the impact on the formability of superplastic forming of the respond to the grain size, elongation and oxidation at different temperatures under atmospheric conditions. The material was heating constantly at different time and temperature. After heating, the thickness of high temperature oxidation production was observed through a scanning electron microscope. In addition, the elongation was measured to verify the deformation of superplastic forming sheet metal forming with high temperature tensile test. The results show that the microstructure of the 8090 aluminum alloy is heated at higher temperatures, the rate of oxidation is higher, the formability of the superplastic forming is also better at the higher temperatures. Keywords: superplastic forming, grain size, elongation, high temperature oxidation
Bagheriasl, Reza. "Formability of Aluminum Alloy Sheet at Elevated Temperature." Thesis, 2012. http://hdl.handle.net/10012/7018.
Повний текст джерелаHwan, Chang Ming, and 張明煥. "The Process Simulation and Fabrication Analysis of Superplastic Forming in 7475 Aluminum Alloy." Thesis, 1993. http://ndltd.ncl.edu.tw/handle/19252611213517493529.
Повний текст джерелаHsiao, Chia-liang, and 蕭家良. "The research of blow forming of aluminum alloy sheet for cell phone case." Thesis, 2012. http://ndltd.ncl.edu.tw/handle/37590771705818080348.
Повний текст джерела國立中央大學
機械工程研究所碩士在職專班
100
In this study, we applied the blow molding process with the aluminum alloy AA5083 H18 material for the metal case of the cell phone products. Firstly, we use the superplastic forming machine to blow the rectangular opening box that similar to cell phone case. In recent years the trend of 3C products tend to be light, thin, short, small and variability, so It is the objective of this study the blow molding process applications on the mobile phone products, And it would need to achieve fast blow molding, small radius on the outline edge of the mobile phone products and 3D pattern appearance of the mobile phone product surface. Therefore, this study was started to experiment with the existing tooling hand-made plate. Firstly, the molding conditions are divided into two groups. One of group was fixed-forming temperature with the different molding pressure and time. Another group was fixed molding pressure and time with the different molding temperature. Base on the datum of the two groups to find out the relation by forming temperature, forming pressure, forming time, the radius of the outline surface and the fine line of the outline surface. Finally to apply the adjusted-forming condition we find with the vendor’s tooling plate to blow the finished product with fine line on the surface.
Shiu, Feng-Ming, and 許峰銘. "The Analysis of Spinning Forming of Automobile’s Hub form 6061 Aluminum Alloy Billet." Thesis, 2011. http://ndltd.ncl.edu.tw/handle/v4438f.
Повний текст джерела國立虎尾科技大學
創意工程與精密科技研究所
99
Hub is one of the important parts in the vehicle; it supports the vehicle weight, appearance, such an important role in steering and driving. As the automobile industry a tendency towards eco-car, comfort, safety, and energy saving which meaning the light weight design of automobile is more important. The wheel hub has a direct impact on the performance of the car''s lifetime, appearance, safety and comfort. The advantages of aluminum alloy wheels which is elegantly、highly strength, better heat dissipation, nature lightly, safely function and highly changeable external, less recycling cost all can drop the automobile oil consumption off. As the melting point is low which is easy to integrate all of the parts in the one and cover the parts quantities. It can reduce the automotive research and development and manufacturing cost. In view of the various factors, the aluminum alloy wheels have gradually replaced steel wheels. It symbolizes the high quality and also it’s widely used in the automotive industry. Spinning forming process is a complex process for an advanced manufacturing technology that has gradually applied to manufacture and produce in the automobile hub. To study and assay the spin forming process on the wheel which establishes a realistic mechanical model. To simulate the spin process which using DEFORM-3D to analysis aluminum alloy material of 6061. To analyze the variable area according to the metal flowing and plastic forming in spin process of the stress distribution. The reference data in accordance with taking shape and optimization of processing effectively.
JIAN, ZIH-WUN, and 簡子文. "A Simulation Analysis of Aluminum Alloy A6061 on T-section Compression by Roll Forming." Thesis, 2016. http://ndltd.ncl.edu.tw/handle/89965533774288345076.
Повний текст джерела國立高雄應用科技大學
模具工程系
104
For the purpose of simulated the process of plate on T-section compression by roll forming, the finite element software Deform 3D was used. The main selected material was A6061 aluminum which was most usually used for industry, setting up the reduction as fixed 10 percent on the protrusion at middle of the plate, and gradually increased the reduction on the side of plate by 15 percent, 20 percent, 25 percent and 30 percent. By the way of symmetric compression of same rollers radius roll forming when A6061 aluminum was used, investigated the influences during roll forming including the load on roller, width spread ratio and curvature of product by changing up parameters including thickness ratio of plate, gap width ratio of top roller, width of plate and coulomb friction coefficient, then according these results, then comparing with different materials including Brass-CDA-110 and SUS304 stainless steel that had different strength coefficient and hardening exponent. By the way of asymmetric compression of different radius rollers roll forming, investigate the influences during roll forming by changing up diameter ratio of rollers and coulomb friction on the plate contacting both top and bottom rollers. Finally, set reductions of plate fixed on middle for 10 percent and side for 20 percent, and investigated the influences of different coulomb friction coefficient and roller diameter for SUS304 stainless steel plate which had relatively highest strength coefficient and hardening exponent was between A6061 and Brass-CDA-110 on T-section compression by symmetric of same rollers radius roll forming. According to results from simulations of A6061 aluminum on T-section com-pression by symmetric of same rollers radius roll forming, when thickness ratio of plate and gap width ratio of the top roller increases, the curvature of product decreases, when coulomb friction coefficient and width of plate increases, the width spread ratio of product decreases. By the way of asymmetric of different rollers radius roll forming, when roller diameter ratio increased, the curvature of product trended to be flat. According to results from simulations of SUS304 stainless steel on T-section compression by symmetric of same rollers radius roll forming, when smaller diameter of roller was used and decreased coulomb friction coefficient, the product would adhere to bottom roller, even caused damages during the roll forming process.
CHANG, YU-HSIEN, and 張育賢. "Study on Formability of Thin Sheet of Aluminum Alloy by Using Servo Forming Technology." Thesis, 2019. http://ndltd.ncl.edu.tw/handle/8eqm34.
Повний текст джерела國立高雄科技大學
機械工程系
107
With the advancement of current process and manufacturing technology, the performance and the shape of the product gradually changed from a single profile and single function to a complex geometry and versatility. Taking multi-stage sheet metal forming as an example, it is easy to cause the material to springback after the various stages are formed, because the stroke of the equipment is fixed in the traditional process. In order to solve this problem, it is necessary to control the springback state of the material in the process with the shaping process, which not only causes the R&D cost to increase but also reduces the overall production capacity. In recent years, researchers have proposed an innovative forming method called servo forming, which can be formed with different kinds of punch motion curves under the fixed strokes (such as crank, hold, vibration motion curve etc.) to achieve stress relaxation. In this study, the results of servoformability were simulated by a small aluminum alloy cup, and the servo stamping curve with dead time and the dynamic hardening model with Simufact.Forming material were used in the servo forming curve. When the speed is stagnant for 60 seconds and the dynamic hardening parameter (γ) of the material is 8, the best formability is obtained, which means that the combination of the parameters can obtain the best predictive cup height performance.
Weng, Cheng-hsien, and 翁正諴. "Superplasticity Effect Demonstrated by Gas Forming Superplastic 5083 and non-Superplastic 5052 Aluminum Alloy." Thesis, 2014. http://ndltd.ncl.edu.tw/handle/95706334888953043947.
Повний текст джерела國立中央大學
機械工程學系
102
This thesis focuses on using superplastic forming to manufacture the aluminum "Airplane Fairing Cover" used on an actual commercial airliner. General superplastic forming usually uses flat sheet to produce symmetrical and less depth-width shape contour, however, the complicated and non-symmetrical work pieces are rarely produced by using superplastic forming. The sheet contour deform is large when flat sheet do the bending process, because fairing cover forming mold have complex shape, high aspect-ratio and the mold V-shape is deeper than middle saddle zone. Finally, wrinkle phenomenon occur in the forming results, and it is occur inside the cutting line area (Ending Opposite Position, EOP) of the product. In order to get the best forming result (i.e. fairing cover) and solve this problem, several improvement are perform, such as: blow with different P-T curve conditions, different material and material thickness usage (AA5052 and SP5083) and reduce the depth of V-side by modify mold (by add pads to reduce the mold cost).
Chiang, Chun-Hsien, and 江俊憲. "The study on microstructure and properties of spray forming and conventional casting AC9A aluminum alloy." Thesis, 2000. http://ndltd.ncl.edu.tw/handle/84221230732713605494.
Повний текст джерела國立成功大學
材料科學及工程學系
88
Spray Forming Process is a rapidly solidified process; materials produced by this process have the characteristics of fine grains and slight segregations. High silicon hypereutectic Al-Si alloys have better wear resistance. During solidification, the primary silicon will be produced first, so these materials can be provided high wear behaviors with primary silicons. Materials using in present study are JIS-AC9A Aluminum alloy. In this study, we will compare the difference of microstructures and mechanical properties between Spray Forming Process (SFP) and Squeeze Casting (SC) materials. For the SFP materials, the primary silicon sizes will be smaller than SC materials and the segregation will be slighter, too. For the SFP materials, the micro hardness values (measured from matrix) will be higher than SC materials at any heat treatment conditions, but the macro hardness (including silicons and matrix) will have no significant difference. From the aging hardening curve and observation of over aging specimens, we can find obvious hardening phenomena and some precipitates, but from the analysis of XRD, there are not any diffraction peaks of precipitates. About fracture energy, the SFP materials can absorb higher energy than SC materials, which results from the difference of silicon particle appearance between SFP and SC materials. Finally, present study will discuss the behavior of silicon particle coarsening at semisolid state, and plot particle coarsening curve to be a reference for SFP materials during formation at semisolid state.
Weng, Ching-Chung, and 翁清浚. "A Study of the Technology Development of Quick Plastic Forming (QPF) for Aluminum Alloy Sheet." Thesis, 2016. http://ndltd.ncl.edu.tw/handle/64271465670580390439.
Повний текст джерела國立中央大學
機械工程學系在職專班
104
The technology of "Superplastic Forming" was used ripely in the aerospace industry for many years. However, it extended to the automotive industry but cannot application generally because its production is slow. At this time, a practical technology in foundation of superplastic forming was developed by U.S. General Motors and called " Quick Plastic Forming, QPF", as well as it was used successfully to the production process for automobile body parts with aluminum alloy. Fortunately "automotive body lightweight" is already the common trend of development by the automobile industry in various countries. The only way is that them are made by high-strength thin steel, aluminum alloy, composite or magnesium alloy. The latter two donot seem real, and the competitiveness of each of the first two should be inconclusive.So aluminum alloy among others has become the main options of materials for automobile body. The development of a viable forming technology for aluminum alloy is importance and cost-effectiveness relatively. Therefore, the important course and experience of technology development of QPF by U.S. General Motors is deserved to understanding and learning deeply. In view of the domestic academia or automobile industry does not research to QPF basically, wherefore the present study is based on this view and prepares for domestic possible requirement in the future. Through a large number of primary and secondary literature review mode, the development, technical features and important achievement of QPF are investigated and inductive analyzed. In addition to propose the suggests for future research direction, the present study expects to provide that domestic interested industries and following researchers deliberate and apply.
YE, CHAN-HONG, and 葉展宏. "Study on Thickness Distribution and Spring Back Phenomena of Sheet-Bulk Forming for Aluminum Alloy." Thesis, 2017. http://ndltd.ncl.edu.tw/handle/70220663549864595342.
Повний текст джерела國立高雄應用科技大學
機械工程系
105
With the improvement of process technology, Aluminum alloy is widely used in many industries. The function of aluminum alloy product gradually change to functional integration of product from a single function. It is important to study the formability and spring back phenomena of thick aluminum alloy sheet. In this study, we used Deform 3D and Simufact.forming to simulate the sheet-bulk forming for thick aluminum alloy sheet. Mesh convergence analysis was conducted to find the optimal element size. Thickness distribution and spring back phenomena of the rectangular blank with round corners feature at process one was also investigated. Simulation results were compared to scanning file based on spring back phenomena. The results are as follows: the optimal element size is 2 mm in the mesh convergence analysis. Compared to tetrahedral elements, solid-shell elements are suitable for analyzing sheet bulk metal forming process. Cross section near binder area of the x-axis and near quarter of keyboard of the y-axis area it has minimum spring back phenomena.
李翰文. "A Study on the High Strenth Aluminum Alloy Produced by the Semi-solids Forming Method." Thesis, 1997. http://ndltd.ncl.edu.tw/handle/63169778360559108396.
Повний текст джерелаChang, Jung-Kuei 1975. "The effect of microstructure on cavitation during hot deformation in fine-grained AA5083 aluminum alloy sheet material." 2008. http://hdl.handle.net/2152/18230.
Повний текст джерелаtext
Chen, Jih-Hsing, and 陳日興. "Investigation on Computer-aided Evaluation of Forming Limit in Cold Forging of High Strength Aluminum Alloy." Thesis, 2003. http://ndltd.ncl.edu.tw/handle/26681276113153251438.
Повний текст джерела國立成功大學
機械工程學系碩博士班
91
To investigate the fracture on the free surface in upsetting process, five different ductile fracture criteria are evaluated in this research. The evaluated criteria include equivalent stress, maximum tensile stress, normalized maximum tensile stress, void growth and coalescence, and hydrostatic stress. After the most adoptable fracture criterion being obtained, we can identify the billet fractured or not by this criterion. In this research, we used the limit strain data measured in the literature to evaluate the most adoptable fracture criterion. After the most adoptable fracture criterion being obtained, it is then used to create simulation model by the DEFORM-3D software to predict the forming limits under different process conditions. The simulation of cylinder compression for the Al-2017F alloy was performed in different friction conditions and height/diameter ratios. The evaluated results show that the Cockcroft and Latham ductile fracture criterion is the most suitable for the fracture prediction in upsetting process. From the simulated results, friction coefficient and the height/diameter ratio will not change the fracture locus. The suddenly change of friction coefficient during experiments will affect the strain path, thus affecting the formability of the billet. With the proposed method, the construction of the forming limit diagram (FLD) can be simplified by selecting proper ductile fracture criteria during finite element simulation and comparing the simulated result with a few experimental results. Thus, the identification of fracture during process parameter optimization can be made.
CHENG, JEN-CHAN, and 鄭任展. "Study on the Production of 5083 Aluminum Alloy Mobile Phone Case by Quick Plastic Forming (QPF)." Thesis, 2019. http://ndltd.ncl.edu.tw/handle/72t6ks.
Повний текст джерела國立中央大學
機械工程學系
107
The paper is based on Quick Plastic Forming (QPF), which is made of 5083 aluminum alloy and superplastic 5083 aluminum alloy to make metal mobile phone casing. The experimental research discusses the fastest time to blow different thickness AA5083 coffins and compare them. The differences between AA5083 and SPF5083 materials are observed and discussed in terms of microstructure. The differences between AA5083 general grain and SPF5083 fine-grained materials are discussed. The thickness and uniformity of the raw materials and processed materials are discussed in various mechanical properties. Size results to explore and evaluate the fastest and most efficient blowing time. The experiment is mainly divided into three parts, the first part is to discuss AA5083 aluminum alloy 0.8mm material, the second part is to discuss AA5083 aluminum alloy metal material 0.6mm material, the third part is to discuss AA5083 and SPF5083 aluminum alloy 0.9mm aluminum alloy metal material and integrate The effect of each part time on size and thickness uniformity.
Yu-YiChu and 朱祐誼. "Study on High Strain Rate Process Characteristics and Flow Stress in Electromagnetic Forming of Aluminum Alloy Sheet." Thesis, 2013. http://ndltd.ncl.edu.tw/handle/75159616791721868373.
Повний текст джерела國立成功大學
機械工程學系碩博士班
101
Electromagnetic forming (EMF) is a high strain rate forming process which exhibits significant advantages, such as increasing the formability of material, improving the springback of aluminum alloy and mitigating the wrinkling occurred in the tube compression process. Because of the particular advantages, EMF achieves a better forming result for complicated geometry which is difficult to be formed by conventional forming processes. In this research, a free impact sheet forming experiment was designed to examine the influence of frequency on the acceleration and impacting velocity. Moreover, a novel separable field shaper design was proposed to assist the EMF process. The efficiency of the field shaper under different geometric parameters was evaluated through the combination of Taguchi method and 3D coupled simulation, which is performed by coupled mechanical and electromagnetic simulation software, LS-DYNA EM module. In the experiment, a high-speed camera was used to record the free flying process, from which the retrieved images were used to characterize the forming velocity. Additionally, based on the described experimental set-up, a simple novel method based on the iteration procedure was proposed to determine the flow stress curve of aluminum alloy 1100-O at high strain rates. Examining the analysis results, the frequency seems to have a more significant effect than the skin depth on electromagnetic forming. In the frequency range between 4 kHz and 11.3 kHz, the skin effect is not a critical parameter and can be neglected. For the field shaper design, the results denote that the slit feature determines the performance of a field shaper. Wider slits reduce the energy loss resulting from electromagnetic repulsion. In addition, with more components of a field shaper, the generated magnetic pressure will be distributed more evenly. Based on the analysis result of the non-symmetric edge effect, some guidelines for designing field shaper are proposed. In addition, using the determined flow stress curve to simulate the forming process, the simulated deformation performed good agreement with the experimental result, where the deviation of effective strain could be reduced from 17.9% to 6.74%. Besides, the effective strains reached in these high rate forming experiments exceed the effective strain at failure determined in a quasi-static tensile test. Under the strain rate of 2800 s-1, the AA 1100-O material could be deformed to effective strain of 0.56 without fracture.
Wu, Hung-Chi, and 吳泓錡. "A crystal plasticity study on the effect of precipitation and warm forming of 6000 series aluminum alloy." Thesis, 2019. http://ndltd.ncl.edu.tw/handle/8w28zc.
Повний текст джерела國立臺灣大學
土木工程學研究所
107
Lightweighting is an important technology trend in the automotive industry. To this end, aluminum alloys have now emerged as a strong candidate of lightweight materials for the industry. For 6000-series aluminum alloys, both microstructural controls and warm forming techniques are the key issues to be resolved in the automotive application. Crystal plasticity finite element method (CPFEM) that links slip activities with mechanical properties is a natural choice to study these issues. The objective of this study is to incorporate proper precipitate hardening and temperature effects into CPFEM. It is well-known that in the physical-based CPFEM (or implicit model), the effect of geometrically necessary dislocation (GND) is averaged in the constitutive law. This study also extends the implicit model with different precipitate geometries (aka, explicit model) and investigate their effects on texture and mechanical behavior. The constitutive model is implemented in Abaqus UMAT. Geometries of precipitate such as shape, size, distribution and volume fraction are considered by Dream.3D. In contrast with the implicit model, the local dislocation density, stress concentration and misorientation around precipitate can be predicted by the explicit model. Moreover, the activating slip systems are analyzed under various crystal orientations and types of precipitate. Finally, we apply CPFEM to study surface roughening effects and texture under plane stain tensile loading. We find that texture band causes surface roughening and higher temperature increases surface roughening effect. In addition, deformation incompatibility between precipitate and crystal limit grain rotation. A 6000 series aluminum alloy, AA6016-T4P, is analyzed under tensile loading. Dislocation density accumulated around precipitate and grain boundary was successfully predicted. Grain orientations after deformation are found to be preferable in <100>//RD.
Zhang, Yi-zong, and 張益綜. "Zr-based and Zr-Cu based Glass-forming Films for Fatigue-property Improvements of 7075-T6 Aluminum Alloy." Thesis, 2011. http://ndltd.ncl.edu.tw/handle/98008095198122246510.
Повний текст джерела國立中央大學
機械工程研究所
99
We proposed with the Zr-based and Zr-Cu based metallic glass thin film (MGTF) as promising coating for aluminum alloy fatigue property enhancement. According to the four-point-bending fatigue results, 7075-T6 aluminum alloy with a 200-nm-thick Zr-based MGTF improved its fatigue life cycle 22 times at a stress level of 250 MPa than the bare one. And the other fatigue life cycle of Zr-Cu based MGTF is further improved 44 times which ups to 107 cycles. The improvements of MGTF coating samples in fatigue limit were 235 MPa (56.7 % increase) and 250 MPa (66.7 % increase) for Zr-based and Zr-Cu based glass-forming film, respectively, and 150 MPa for uncoated sample. The films actually restrict the surface offsets and cracks propagating during the fatigue test. Zr-Cu based glass-forming film have better fatigue resistance than Zr-based MGTF, the fatigue life had improved by more than 2 times under a stress of 250 MPa, due to higher hardness and strength, better plasticity, thus it exhibits better improvement in fatigue property. A 50-nm-thick Titanium buffer layer between the film and the substrate was reported adhesion enhancement. The superior mechanical properties of MGTF, such as high strength and good bending ductility, coupled with good adhesion between the film and the substrate as well as the reduced surface roughness, and high compressive residual stress of the metallic film yield the fatigue property improvement of aluminum alloy. Thus demonstrating MGTF as promising coating materials for improving the fatigue properties of materials, and further applied to aerospace, automobile industry and bicycle manufacturing etc.
Ming, Huang Sin, and 黃信銘. "Study on Gas Forming of Superplastic 5083 and non-Superplastic 5083 Aluminum Alloy Sheet for Cell Phone Shell." Thesis, 2018. http://ndltd.ncl.edu.tw/handle/quqdyn.
Повний текст джерела國立中央大學
機械工程學系
106
This thesis focuses on the application of quick plastic forming (QPF) process to the molding of metal cellphone shell. The experiments used different type of commercial 5083 and superplastic 5083 aluminum alloy sheet to carry out cellphone shell quick plastic forming at different times. Through a variety of mechanical properties and formability tests, to discuss the advantages of the quick plastic forming process to produce a cellphone shell, and which kind of sheet are more suitable as material for the quick plastic forming of cellphone shell. The results show that the effect of one stage quick plastic forming on the complete forming is the design of the mold, rather than the mechanical properties of material, and the mechanical properties of material is not much difference before and after forming. Based on the above results, it can be inferred that in order to make cellphone shell efficiently using the quick plastic forming process in aspect of economy and time, commercial 5083 sheet is the better choose for material.
Vanegas, Moller Ricardo. "Design and fabrication of an instrument to test the mechanical behavior of aluminum alloy sheets during high-temperature gas-pressure blow-forming." 2008. http://hdl.handle.net/2152/10498.
Повний текст джерелаtext
Carvalheiro, Cátia Gomes. "Estudo numérico do retorno elástico torcional em componentes de geometria complexa." Master's thesis, 2021. http://hdl.handle.net/10316/96218.
Повний текст джерелаDevido ao esforço constante em reduzir o peso dos veículos e atender à pressão da economia para que se aumente a sua segurança, os aços avançados de alta resistência e as ligas de alumínio estão a ganhar cada vez mais popularidade. A relação entre resistência e peso nestes materiais é muito superior quando comparada com outros materiais, enquanto a ductilidade é similar. No entanto, o elevado retorno elástico após a conformação plástica é uma das desvantagens destes materiais, comprometendo a qualidade do produto final. Para prever a ocorrência de defeitos durante o processo de estampagem e posteriormente fazer a sua correção têm sido desenvolvidas ferramentas de produção virtual, nomeadamente a simulação numérica com o método dos elementos finitos. Desta forma, uma previsão correta permite reduzir o ciclo de desenvolvimento das ferramentas de estampagem, fazendo compensação do retorno elástico sem ter se fazer vários ciclos experimentais de tentativa-erro, poupando tempo e dinheiro.Este estudo tem como objetivo realizar a análise numérica do retorno elástico torcional num componente de geometria complexa, recorrendo ao programa de elementos finitos DD3IMP. Este componente de estudo foi proposto pela organização da conferência NUMISHEET. A modelação do comportamento elasto-plastico do material da chapa utiliza uma vasta gama de dados experimentais fornecidos para o aço de alta resistência DP980 e uma liga de alumínio 6xxx. Para além do efeito do material da chapa no retorno elástico, analisa-se também o efeito de outros parâmetros como: (i) coeficiente de atrito; (ii) freio de retenção; (iii) módulo de elasticidade; (iv) lei de encruamento e (v) critério de plasticidade. A análise destes parâmetros é realizada com o auxílio da simulação numérica, nomeadamente fazendo variar cada um destes parâmetros de forma independente.Foram avaliados vários parâmetros, tais como a evolução da força do punção e do cerra-chapas, o escoamento da chapa, o retorno elástico e o retorno elástico torcional na parte superior do componente e em toda a geometria do componente. Após análise dos resultados concluiu-se que a liga de alumínio apresenta menor retorno elástico em comparação com o aço. Por outro lado, o parâmetro com maior impacto no retorno elástico é a presença do freio de retenção, i.e. o retorno elástico é significativamente reduzido quando se utiliza um freio de retenção. Por outro lado, a anisotropia plástica do material da chapa tem pouca importância para o retorno elástico.
As a result of the constant effort to reduce vehicle weight and meet the economic pressure to increase their safety, advanced high strength steels and aluminum alloys are gaining increasing popularity. The relationship between materials strength and weight is much higher when compared to other materials, while the ductility is similar. However, the high springback after forming is one of the disadvantages of these materials, compromising the quality of the final product due to shape deviation. To predict the occurrence of defects during the stamping process and subsequently correct them, virtual production tools were developed, namely a numerical simulation with the finite element method. In this way, a correct prediction allows to reduce the development cycle of the stamping tools, compensating for the springback without having to do several experimental trial-error cycles, saving time and money.This study aims to perform the numerical analysis of the torsional springback in a complex geometry component, using the finite element code DD3IMP. This component was proposed by the organization of the NUMISHEET conference. Modeling the elasto-plastic behavior of the sheet material uses a wide range of experimental data provided for DP980 steel and a 6xxx aluminum alloy. In addition to the effect of the sheet material on the springback, the effect of other parameters is also analyzed, such as: (i) friction coefficient; (ii) beads; (iii) modulus of elasticity; (iv) work hardening law and (v) yield criterion. The analysis of these parameters is carried out with the aid of numerical simulation, namely by changing each of these parameters independently.Various parameters were evaluated, such as the evolution of punch and blank holder force, sheet draw-in, springback and twist springback on top of the component and across the component geometry. It was concluded that the aluminum alloy has a lower springback compared to steel. On the other hand, the parameter with the largest impact on springback is the presence of beads, i.e. the springback is significantly reduced when using beads. On the other hand, the plastic anisotropy of the sheet material is of little importance on the springback.
金武, 直幸, 眞. 小橋 та 博仁 平. "金属基複合材料の部分使用に適した固相接合・複合プロセスの開発". 1999. http://hdl.handle.net/2237/13076.
Повний текст джерела金武, 直幸, 孝至 伊藤, 眞. 小橋, 秀男 佐野 та 俊勝 小池. "圧縮・せん断複合負荷による高機能軽金属粉末の組織制御成形法". 2002. http://hdl.handle.net/2237/13117.
Повний текст джерела