Livros sobre o tema "Surface slope"

Weak rocks encountered in open pit mines cover a wide variety of materials, with properties ranging between soil and rock. As such, they can provide a significant challenge for the slope designer. For these materials, the mass strength can be the primary control in the design of the pit slopes, although structures can also play an important role. Because of the typically weak nature of the materials, groundwater and surface water can also have a controlling influence on stability. Guidelines for Open Pit Slope Design in Weak Rocks is a companion to Guidelines for Open Pit Slope Design, which was published in 2009 and dealt primarily with strong rocks. Both books were commissioned under the Large Open Pit (LOP) project, which is sponsored by major mining companies. These books provide summaries of the current state of practice for the design, implementation and assessment of slopes in open pits, with a view to meeting the requirements of safety, as well as the recovery of anticipated ore reserves. This book, which follows the general cycle of the slope design process for open pits, contains 12 chapters. These chapters were compiled and written by industry experts and contain a large number of case histories. The initial chapters address field data collection, the critical aspects of determining the strength of weak rocks, the role of groundwater in weak rock slope stability and slope design considerations, which can differ somewhat from those applied to strong rock. The subsequent chapters address the principal weak rock types that are encountered in open pit mines, including cemented colluvial sediments, weak sedimentary mudstone rocks, soft coals and chalk, weak limestone, saprolite, soft iron ores and other leached rocks, and hydrothermally altered rocks. A final chapter deals with design implementation aspects, including mine planning, monitoring, surface water control and closure of weak rock slopes. As with the other books in this series, Guidelines for Open Pit Slope Design in Weak Rocks provides guidance to practitioners involved in the design and implementation of open pit slopes, particularly geotechnical engineers, mining engineers, geologists and other personnel working at operating mines.

A new type of illusion, called the antigravity slope illusion, is presented in this chapter. In this illusion a slope orientation is perceived opposite to the true orientation and hence a ball put on it appears to be rolling uphill, defying the law of gravity. This illusion is based on the ambiguity in the distance from a viewpoint to the surface of a three-dimensional solid represented in a single-view image. This illusion also arises in human real life, for example, when a car driver misunderstands the orientation of a road along which he or she is driving. Two assumptions are explored: (a) the human brain prefers to interpret vertical columns in a two-dimensional image as being vertical in three-dimensional space to being slanted and (b) the human brain prefers the most symmetric shape as the interpretation of a two-dimensional image.

An effective response to bushfires relies on accurate predictions of fire behaviour, particularly the rate of spread, intensity and ‘spotting’. This field guide has been developed to provide a systematic method for assessing fuel hazard and predicting potential fire behaviour in dry eucalypt forest. It will assist in making vital decisions that ensure the protection of fire crews and the community. This guide integrates Project Vesta research findings with the Victorian Overall Fuel Hazard Guide and is applicable to dry eucalypt forests throughout southern Australia. Fuel assessment is based on the hazard scoring system employed during Project Vesta which investigated the effects of fuel age and understorey vegetation structure on fire behaviour in these forests. Information provided in this guide can be used to: Define and identify different fuel layers and components of fuel structure and hazard; Determine the hazard score of surface and near-surface fuel layers and the height of the near-surface fuel for fire spread prediction; Determine elevated fuel height for flame height prediction; and determine surface fuel hazard score and bark hazard score for spotting distance prediction. The Field Guide provides tables to predict the potential rate of spread of a bushfire burning in dry eucalypt forest under summer conditions, and can also be used to predict flame height and maximum spotting distance. The guide also allows users to determine the moisture content of fine dead fuels throughout the day, and to account for the effect of slope on the rate of spread of a fire.

The aim of the paper was to determine the influence of root systems of chosen tree species found in the Polish Flysch Carpathians on the increase of soil shear strength (root cohesion) in terms of slope stability. The paper's goal was achieved through comprehensive tests on root systems of eight relatively common in the Polish Flysch Carpathians tree species. The tests that were carried out included field work, laboratory work and analytical calculations. As part of the field work, the root area ratio (A IA) of the roots was determined using the method of profiling the walls of the trench at a distance of about 1.0 m from the tree trunk. The width of the. trenches was about 1.0 m, and their depth depended on the ground conditions and ranged from 0.6 to 1.0 m below the ground level. After preparing the walls of the trench, the profile was divided into vertical layers with a height of 0.1 m, within which root diameters were measured. Roots with diameters from 1 to 10 mm were taken into consideration in root area ratio calculations in accordance with the generally accepted methodology for this type of tests. These measurements were made in Biegnik (silver fir), Ropica Polska (silver birch, black locust) and Szymbark (silver birch, European beech, European hornbeam, silver fir, sycamore maple, Scots pine, European spruce) located near Gorlice (The Low Beskids) in areas with unplanned forest management. In case of each tested tree species the samples of roots were taken, transported to the laboratory and then saturated with water for at least one day. Before testing the samples were obtained from the water and stretched in a. tensile testing machine in order to determine their tensile strength and flexibility. In general, over 2200 root samples were tested. The results of tests on root area ratio of root systems and their tensile strength were used to determine the value of increase in shear strength of the soils, called root cohesion. To this purpose a classic Wu-Waldron calculation model was used as well as two types of bundle models, the so called static model (Fiber Bundle Model — FIRM, FBM2, FBM3) and the deformation model (Root Bundle Model— RBM1, RBM2, mRBM1) that differ in terms of the assumptions concerning the way the tensile force is distributed to the roots as well as the range of parameters taken into account during calculations. The stability analysis of 8 landslides in forest areas of Cicikowicleie and Wignickie Foothills was a form of verification of relevance of the obtained calculation results. The results of tests on root area ratio in the profile showed that, as expected, the number of roots in the soil profile and their ApIA values are very variable. It was shown that the values of the root area ratio of the tested tree species with a diameter 1-10 ram are a maximum of 0.8% close to the surface of the ground and they decrease along with the depth reaching the values at least one order of magnitude lower than close to the surface at the depth 0.5-1.0 m below the ground level. Average values of the root area ratio within the soil profile were from 0.05 to 0.13% adequately for Scots pine and European beech. The measured values of the root area ratio are relatively low in relation to the values of this parameter given in literature, which is probably connected with great cohesiveness of the soils and the fact that there were a lot of rock fragments in the soil, where the tests were carried out. Calculation results of the Gale-Grigal function indicate that a distribution of roots in the soil profile is similar for the tested species, apart from the silver fir from Bie§nik and European hornbeam. Considering the number of roots, their distribution in the soil profile and the root area ratio it appears that — considering slope stability — the root systems of European beech and black locust are the most optimal, which coincides with tests results given in literature. The results of tensile strength tests showed that the roots of the tested tree species have different tensile strength. The roots of European beech and European hornbeam had high tensile strength, whereas the roots of conifers and silver birch in deciduous trees — low. The analysis of test results also showed that the roots of the studied tree species are characterized by high variability of mechanical properties. The values Of shear strength increase are mainly related to the number and size (diameter) of the roots in the soil profile as well as their tensile strength and pullout resistance, although they can also result from the used calculation method (calculation model). The tests showed that the distribution of roots in the soil and their tensile strength are characterized by large variability, which allows the conclusion that using typical geotechnical calculations, which take into consideration the role of root systems is exposed to a high risk of overestimating their influence on the soil reinforcement. hence, while determining or assuming the increase in shear strength of soil reinforced with roots (root cohesion) for design calculations, a conservative (careful) approach that includes the most unfavourable values of this parameter should be used. Tests showed that the values of shear strength increase of the soil reinforced with roots calculated using Wu-Waldron model in extreme cases are three times higher than the values calculated using bundle models. In general, the most conservative calculation results of the shear strength increase were obtained using deformation bundle models: RBM2 (RBMw) or mRBM1. RBM2 model considers the variability of strength characteristics of soils described by Weibull survival function and in most cases gives the lowest values of the shear strength increase, which usually constitute 50% of the values of shear strength increase determined using classic Wu-Waldron model. Whereas the second model (mRBM1.) considers averaged values of roots strength parameters as well as the possibility that two main mechanism of destruction of a root bundle - rupture and pulling out - can occur at the same. time. The values of shear strength increase calculated using this model were the lowest in case of beech and hornbeam roots, which had high tensile strength. It indicates that in the surface part of the profile (down to 0.2 m below the ground level), primarily in case of deciduous trees, the main mechanism of failure of the root bundle will be pulling out. However, this model requires the knowledge of a much greater number of geometrical parameters of roots and geotechnical parameters of soil, and additionally it is very sensitive to input data. Therefore, it seems practical to use the RBM2 model to assess the influence of roots on the soil shear strength increase, and in order to obtain safe results of calculations in the surface part of the profile, the Weibull shape coefficient equal to 1.0 can be assumed. On the other hand, the Wu-Waldron model can be used for the initial assessment of the shear strength increase of soil reinforced with roots in the situation, where the deformation properties of the root system and its interaction with the soil are not considered, although the values of the shear strength increase calculated using this model should be corrected and reduced by half. Test results indicate that in terms of slope stability the root systems of beech and hornbeam have the most favourable properties - their maximum effect of soil reinforcement in the profile to the depth of 0.5 m does not usually exceed 30 kPa, and to the depth of 1 m - 20 kPa. The root systems of conifers have the least impact on the slope reinforcement, usually increasing the soil shear strength by less than 5 kPa. These values coincide to a large extent with the range of shear strength increase obtained from the direct shear test as well as results of stability analysis given in literature and carried out as part of this work. The analysis of the literature indicates that the methods of measuring tree's root systems as well as their interpretation are very different, which often limits the possibilities of comparing test results. This indicates the need to systematize this type of tests and for this purpose a root distribution model (RDM) can be used, which can be integrated with any deformation bundle model (RBM). A combination of these two calculation models allows the range of soil reinforcement around trees to be determined and this information might be used in practice, while planning bioengineering procedures in areas exposed to surface mass movements. The functionality of this solution can be increased by considering the dynamics of plant develop¬ment in the calculations. This, however, requires conducting this type of research in order to obtain more data.

The Tibetan Plateau (TP) is the largest and highest plateau on Earth. Due to its elevation, it receives much more downward shortwave radiation than other areas, which results in very strong diurnal and seasonal changes of the surface energy components and other meteorological variables, such as surface temperature and the convective atmospheric boundary layer. With such unique land process conditions on a distinct geomorphic unit, the TP has been identified as having the strongest land/atmosphere interactions in the mid-latitudes.Three major TP land/atmosphere interaction issues are presented in this article: (1) Scientists have long been aware of the role of the TP in atmospheric circulation. The view that the TP’s thermal and dynamic forcing drives the Asian monsoon has been prevalent in the literature for decades. In addition to the TP’s topographic effect, diagnostic and modeling studies have shown that the TP provides a huge, elevated heat source to the middle troposphere, and that the sensible heat pump plays a major role in the regional climate and in the formation of the Asian monsoon. Recent modeling studies, however, suggest that the south and west slopes of the Himalayas produce a strong monsoon by insulating warm and moist tropical air from the cold and dry extratropics, so the TP heat source cannot be considered as a factor for driving the Indian monsoon. The climate models’ shortcomings have been speculated to cause the discrepancies/controversies in the modeling results in this aspect. (2) The TP snow cover and Asian monsoon relationship is considered as another hot topic in TP land/atmosphere interaction studies and was proposed as early as 1884. Using ground measurements and remote sensing data available since the 1970s, a number of studies have confirmed the empirical relationship between TP snow cover and the Asian monsoon, albeit sometimes with different signs. Sensitivity studies using numerical modeling have also demonstrated the effects of snow on the monsoon but were normally tested with specified extreme snow cover conditions. There are also controversies regarding the possible mechanisms through which snow affects the monsoon. Currently, snow is no longer a factor in the statistic prediction model for the Indian monsoon prediction in the Indian Meteorological Department. These controversial issues indicate the necessity of having measurements that are more comprehensive over the TP to better understand the nature of the TP land/atmosphere interactions and evaluate the model-produced results. (3) The TP is one of the major areas in China greatly affected by land degradation due to both natural processes and anthropogenic activities. Preliminary modeling studies have been conducted to assess its possible impact on climate and regional hydrology. Assessments using global and regional models with more realistic TP land degradation data are imperative.Due to high elevation and harsh climate conditions, measurements over the TP used to be sparse. Fortunately, since the 1990s, state-of-the-art observational long-term station networks in the TP and neighboring regions have been established. Four large field experiments since 1996, among many observational activities, are presented in this article. These experiments should greatly help further research on TP land/atmosphere interactions.