Literatura científica selecionada sobre o tema "Nanofibre de cabone"
Crie uma referência precisa em APA, MLA, Chicago, Harvard, e outros estilos
Consulte a lista de atuais artigos, livros, teses, anais de congressos e outras fontes científicas relevantes para o tema "Nanofibre de cabone".
Ao lado de cada fonte na lista de referências, há um botão "Adicionar à bibliografia". Clique e geraremos automaticamente a citação bibliográfica do trabalho escolhido no estilo de citação de que você precisa: APA, MLA, Harvard, Chicago, Vancouver, etc.
Você também pode baixar o texto completo da publicação científica em formato .pdf e ler o resumo do trabalho online se estiver presente nos metadados.
Artigos de revistas sobre o assunto "Nanofibre de cabone"
YAMASHITA, Yoshihiro, Toshimitsu TAKAHASHI, Shunsuke KASUGAI e Akira TANAKA. "Reinforcement Effect of Composite Material Caused by Adding a Small Amount of VGCF Cabon Nanofiber". KOBUNSHI RONBUNSHU 63, n.º 9 (2006): 593–600. http://dx.doi.org/10.1295/koron.63.593.
Texto completo da fontePark, S. H., B. C. Kim, S. M. Jo, D. Y. Kim e W. S. Lee. "Cabon Nanofibrous Materials Prepared from Electrospun Polyacrylonitrile Nanofibers for Hydrogen Storage". MRS Proceedings 837 (2004). http://dx.doi.org/10.1557/proc-837-n3.14.
Texto completo da fonteZhang, Mu, Le Chen, Yang Yu, Xianfeng Meng e Jun Xiang. "Cabon nanofiber supported cobalt ferrite composites with tunable microwave absorption properties". Ceramics International, dezembro de 2020. http://dx.doi.org/10.1016/j.ceramint.2020.12.071.
Texto completo da fonteTeses / dissertações sobre o assunto "Nanofibre de cabone"
Inês, dos Santos Vivian. "Development of alumina-toughened zirconia composites reinforced with carbon nanofibers via direct ink writing". Electronic Thesis or Diss., Lyon, INSA, 2023. https://theses.insa-lyon.fr/publication/2023ISAL0082/these.pdf.
Texto completo da fonteThere is a growing demand for personalized ceramic materials with increasingly complex shapes and properties for biomedical engineering applications, which cannot be achieved via traditional ceramic processing techniques. In recent years, increasing attention has been drawn to ceramic-based materials produced by an additive manufacturing method commonly referred to as direct ink writing (DIW) or Robocasting. However, the current challenge of DIW-produced ceramics remains the achievement of strong mechanical reliability. Hence, in the first chapter, this thesis examines the overall scenario of the DIW field, highlighting and analyzing the primary outcomes of studies available in the literature. It also describes and discusses the most innovative approaches, as well as mechanical and biological improvement strategies for the DIW method. The second chapter of the thesis provides a comprehensive characterization of pastes consisting of an alumina-toughened zirconia (ATZ, 84 vol% Ce-TZP, 8% Al2O3, 8% SrAl12O19) powder, a deflocculant, a binder, deionized water and, in some cases, carbon nanofibers (CNFs). The rheological behavior and fundamental properties of these pastes were determined and printability tests were conducted. The results were compared to established printability criteria/parameters outlined in existing literature (ф, K and FTI). These criteria were found to be suitable for assessing printability, although they presented some limitations in predicting some unprintable pastes. Furthermore, a new criterion based on the recovery rate of the storage modulus was introduced, with the potential to predict printability with a single test. The third and last chapter of the thesis focused on the DIW fabrication of filaments of the same ATZ composite with and without CNFs with the objective of enhancing the mechanical properties by careful debinding and sintering processes, as well as the orientation of the CNFs. Nozzle diameters in the range of 200-840 μm were used and optimal debinding and sintering conditions were determined, using both Conventional Sintering (CS) and Spark Plasma Sintering (SPS) methods. The mechanical evaluation of the filaments included the determination of the fracture stress (flexural strength), fracture strain, Young's modulus and mechanical reliability (Weibull modulus). The addition of the CNFs, expected to improve the mechanical properties, hindered most of them because of CNF agglomeration. Printing with smaller nozzles showed improvements in the Young’s modulus of the filaments, with ATZ filaments sintered by CS exhibiting transformation-induced plasticity (TRIP), while those sintered by SPS did not. The mechanical properties obtained were comparable to or higher than those achieved through conventional ceramic processing techniques like cold isostatic pressing and slip casting. Similarly, a good level of mechanical reliability was achieved
Gotti, Carlo. "Development and mechanical characterization of a biostable Nylon6.6 electrospun nanofibrous multiscale device for tendon and ligament replacement and simulation". Master's thesis, Alma Mater Studiorum - Università di Bologna, 2018. http://amslaurea.unibo.it/15708/.
Texto completo da fonteTrabalhos de conferências sobre o assunto "Nanofibre de cabone"
Thiruvallur Eachambadi, Raghavendran. "Ordered Electrical Network of interconnected Nanofibers observed in Cable Bacteria". In European Microscopy Congress 2020. Royal Microscopical Society, 2021. http://dx.doi.org/10.22443/rms.emc2020.35.
Texto completo da fonte