Literatura científica selecionada sobre o tema "Institut Teknologi 10 Nopember (Surabaya, Indonesia)"

Telah dilakukan perancangan dan pengujian performa turbin air tidal untuk penggerak pompa di tambak garam menggunakan blade hydrofoil standar NACA S814 untuk menghasilkan desain turbin tidal, optimasi bilah turbin tidal dan juga coefficient of power (Cp) pada turbin tidal. Perancangan geometri turbin tidal menggunakan rumus yang tersedia dan pengujian turbin tidal menggunakan bantuan software Qblade. Variasi kecepatan aliran air yang pertama 1 m/s, Variasi kecepatan aliran air yang kedua 1,536 m/s, Variasi kecepatan aliran air yang ketiga 2,072 m/s, Variasi kecepatan aliran air yang keempat 2,608 m/s, Variasi kecepatan aliran air yang kelima 3,144 m/s, Variasi kecepatan aliran air yang keenam 3,68 m/s. Hasil perancangan yang didapatkan adalah panjang chord 0,02 m, panjang blade 0,4 m, diameter poros 0,16 m, diameter bilah 1,1 m, jumlah blade 3. Hasil dari pengujian performa dari turbin tidal untuk masing-masing varian kecepatan adalah 22,474; 9,136; 4,703; 2,642; 1,539; 0,900. Dari data hasil pengujian tersebut diolah dengan menggunakan metoda ANOVA. Kesimpulan yang didapatkan adalah karena nilai F (kecepatan) =2,219512 F crit =2,53355 maka tidak terdapat perbedaan hasil uji pada varian kecepatan dan karena nilai F (uji) =25,59739 F crit =2,42052 maka terdapat perbedaan hasil uji pada varian hasil.Kata kunci: ANOVA, Coefficient of Power,Turbin Tidal, QbladeThe design and performance test of a tidal water turbine for pump driving in salt ponds has been carried out using a standard NACA S814 hydrofoil blade to produce a tidal turbine design, optimization of tidal turbine blades, and also the coefficient of power (Cp) on a tidal turbine. Tidal turbine geometry design using the available formulas and tidal turbine testing using the Qblade software. The first variation of airflow velocity is 1 m/s, the variation of the second airflow velocity is 1.536 m/s, the variation of the third airflow velocity is 2.072 m/s, the variation of the fourth airflow velocity is 2.608 m/s, the fifth variation of airflow velocity is 3.144 m/s, Variation of water flow velocity 3.68 m/s. The design results obtained are chord length 0.02 m, blade length 0.4 m, shaft diameter 0.16 m, blade diameter 1.1 m, number of blades 3. The results of testing the performance of the tidal turbine for each speed variant are 22.474; 9.136; 4,703; 2,642; 1,539; 0.900. From the test results, data are processed using the ANOVA method. The conclusion obtained is because the value of F (speed) = 2.219512 < F crit = 2.53355 then there is no difference in the test results on the speed variant and because the value of F (test) = 25.59739 > F crit = 2.42052 then there is the difference in test results on the variance of results.Keywords : ANOVA, Coefficient of Power, Tidal Turbine, QbladeDAFTAR RUJUKANBaihaqiy, A. R. (2017). Prototype Pembangkit Listrik Tenaga Pasang Surut Air Laut Di Kelurahan Tugurejo Kecematan Tugu Kota Semarang. Universitas Negri Semarang.FE, M. N. S. (2016). Rancang Bangun Simulasi Turbin Air Cross Flow. Jurnal Pendidikan Teknik Mesin, 1(2).Febrianto, A., & Santoso, A. (2017). Analisa perbandingan torsi dan rpm turbin tipe darrieus terhadap efisiensi turbin. Jurnal Teknik ITS, 5(2).Fridayana, E. N. (2018). Analisis Kinerja Aerodinamik dari Vertical Axis Wind Turbine (VAWT) Darrieus Tipe H-Rotor dengan Pendekatan Computational Fluid Dynamic (CFD). Institut Teknologi Sepuluh Nopember,Ginting, J. W., & Setiawan, I. K. D. (2018). Kinerja Prototipe Papan Osilasi Pada Pompa Flap Tenaga Gelombang Untuk Pemanfaatan Mata Air Di Pantai Banyu Asri, Kota Singaraja-Bali. Jurnal Teknik Hidraulik, 9(2).Kurniawan, A., Jaziri, A. A., Amin, A. A., & Salamah, L. N. m. (2019). Indeks Kesesuaian Garam (IKG) Untuk Menentukan Kesesuaian Lokasi Produksi Garam; Analisis Lokasi Produksi Garam Di Kabupaten Tuban Dan Kabupaten Probolinggo. JFMR (Journal of Fisheries and Marine Research), 3(2), 236-244.Lopulalan, R. M. (2016). Desain blade turbin pembangkit listrik tenaga arus laut di Banyuwangi berbasis CFD. Institut Teknologi Sepuluh Nopember Surabaya,Oktavianto, D., Budiarto, U., & Kiryanto, K. (2017). Analisa Pengaruh Variasi Bentuk Sudu, Sudut Serang dan Kecepatan Arus Pada Turbin Arus Tipe Sumbu Vertikal Terhadap Daya yang Dihasilkan Oleh Turbin. Jurnal Teknik Perkapalan, 5(2).Patittingi, F. (2012). Dimensi hukum pulau-pulau kecil di Indonesia: studi atas penguasaan dan pemilikan tanah: Rangkang Education.Priliawan, R. A. (2016). Pengaruh Jumlah Sudu Turbin Wells Dan Variasi Gelombang Laut Terhadap Performa Prototype Pembangkit Listrik Tenaga Gelombang Laut Sistem Oscillating Water Column (OWC).Sapto, A. D., & Rumakso, H. P. (2021). Uji Coba Performa Bentuk Airfoil Menggunakan Software Qblade Terhadap Turbin Angin Tipe Sumbu Horizontal. Jurnal Teknik Mesin, 10(1).Sari, Y. R., & Rani, M. (2021). Penerapan Logika Fuzzy Metode Mamdani Dalam Menyelesaikan Masalah Produksi Garam Nasional. JATISI (Jurnal Teknik Informatika dan Sistem Informasi), 8(1), 341-356.

Olimpiade sains SMP adalah ajang kompetisi dalam bidang Ilmu Pengetahuan Alam (sains) bagi para siswa pada jenjang SMP baik tingkat nasional maupun internasional. Beberapa tujuan olimpiade sains adalah untuk memotivasi para siswa belajar sains, memacu peningkatan mutu pendidikan sains, mencari bibit calon-calon saintis-saintis atau ilmuwan-ilmuwan muda indonesia. Departemen Fisika ITS juga ikut memberikan perhatian terhadap kemampuan siswa dalam bidang sains. Oleh karena itu, departemen Fisika melaksanakan pembinaan olimpiade sains tingkat provinsi bagi Siswa SMP sekota Surabaya. Pada kegiatan ini para dosen pembina memberikan penyelesaian problem fisika yang dianggap rumit dengan cara-cara yang mudah dimengerti oleh para siswa SMP. Hasil dari pelaksanaan kegiatan pembinaan olimpiade sains tingkat provinsi Jawa Timur bagi siswa SMP sekota Surabaya adalah peningkatatan kemampuan siswa dalam menjawab soal-soal olimpiade sains tingkat provinsi. Peningkatan kemampuan ini ditunjukkan dengan adanya peningkatan dari nilai pre-test ke nilai post-test.

This study aims to determine the identity that emerges through language in Indonesian language major in tertiary engineering concentration. The research was conducted in the Department of Marine Engineering, Sepuluh November Institute of Technology Surabaya. The method used is descriptive qualitative with Van Dijk's critical discourse analysis. Van Dijk's three models are macrostructure, social cognition, and microstructure. The results of the study show that identity does not only emerge from a person's psychological background but is also seen from the language used. most students try to use mimicry in using language, that is, students outside Surabaya try to use Suroboyoan as the language of instruction in discussions in the Indonesian class as an effort to bring out their identity as suroboyo architects, no longer their origin areas to be socially acceptable. Other findings, Indonesian language classes bring up the identity associated with the understanding adopted by students.

Education is a major concern of government in enhancing and improving the quality of human resources. Indonesia have stratified formal education which higher education contains of state university and private university. Surabaya is a city in Indonesia which has the largest public universities. There are four universities, there are universitas airlangga (UA), universitas negeri Surabaya (Unesa), institut teknologi sepuluh nopember (ITS), and IAIN sunan ampel. This study aims to test and analyze whether brand awareness, brand association, and perceived quality affect decision to choose state universities in Surabaya. This type of this research is quantitative, using multistage sampling with 377 respondents. Statistical analysis that used is the approach of mutiple linear regression which tested to every object. The results of this study showed that brand awareness and perceived quality has a positive influence on the decision to choose state universities in Surabaya. there are differences in the effect of brand association that the UA and Unesa positive influence while at IAIN Sunan Ampel, ITS and negative effect. Those influences has different athmosphere by respondent of Surabaya’s city branding. There’s not all of the respondent to consider city branding of Surabaya when they choose to study at Surabaya. Keywords: brand awareness, brand association, perceived quality, decision to choose, state university

Tujuan dari pengabdian masyarakat (Abmas) ini adalah memberikan layanan pendampingan fasilitasi sertifikasi halal dengan kategori baik pernyataan pelaku usaha (self declare) maupun regular, yang merupakan salah satu cara yang diharapkan mampu mempercepat pemulihan ekonomi di Surabaya. Hal ini tentu sejalan dengan visi pemerintah yang terus berupaya mendorong Indonesia untuk menjadi produsen produk halal dunia. Sertifikasi halal yang semula voluntary (sukarela), kini telah berubah menjadi mandatory (wajib). Pemberlakuan sertifikasi halal tersebut dilakukan secara bertahap yang dimulai dari produk makanan dan minuman pada tanggal 17 Oktober 2019 dan non-pangan dimulai pada tanggal 17 Oktober 2021. Pelaksanaan kegiatan ini dibagi menjadi 6 tahapan, yaitu seleksi pelaku usaha mikro dan kecil, seleksi mahasiswa kuliah kerja nyata (KKN), workshop kader penggerak halal, pendampingan penyusunan dokumen manual Sistem Jaminan Produk Halal (SJPH), pendaftaran sertifikasi halal, dan pemberian plakat logo binaan pusat kajian halal Institut Teknologi Sepuluh Nopember (ITS). Berdasarkan capaian indikator kesiapan mitra dalam pendaftaran sertifikasi halal dan hasil diskusi dengan tim internal, maka terdapat 11 UMKM yang diberikan rekomendasi dan fasilitasi pendaftaran sertifikasi halal gratis. Adapun 4 UMKM lainnya belum dapat direkomendasikan karena belum memenuhi persyaratan, seperti penggunaan air isi ulang dan daging dari pasar yang belum mempunyai sertifikasi halal.

Besides its role during fermentation process, yeast also has potential as biological agent because of its antagonistics characteristic. We have isolated yeast from six different locations based on Phospourus differences. Isolated yeast were then tested its antagonistics ability of Fusarium oxysporum, the pathogen causing tomato wilt disease. This research aims to find out the diversity of yeast found in the tomato rhizosphere in six different contents of phosphorus locations and to know its antagonistics ability against the pathogenic. F. oxysporum. This research was conducted in the Laboratory of Mycology, Department of Pests and Diseases, Faculty of Agriculture, Brawijaya University, Malang and in the Chemistry Laboratory, Institut Teknologi 10 Nopember Surabaya, started from January up to September 2015. Yeasts have been isolated from tomato’s rhizosphere of 6 different locations around East Java proviences. The result showed that yeasts from organic field (Lower P content) were 6 genera. They are Candida sp. 1, Pichia sp. 1, Hansenula sp., Metschnikowia sp. 1, Cryptococcus sp., and Zygosaccharomyces sp. While the yeasts from inorganic field (higher P) were 3 genera. The most potential yeast in controlling F. oxysporum is Pichia sp. 2. Lower P content showed more divers than higher P content. Yeasts from higher soil P content showed more antagonists to control F. oxysporum. Keywords: Phosphor, correlation, yeast, antagonistic, disease, soil

The MIPA Tower office building, an eleven-storey building, which is located in the area of Institut Teknologi Sepuluh Nopember Surabaya, is under construction. The building will be utilized for offices, classrooms, and laboratories. In the operation of the building, domestic and laboratory wastewater will be produced. This wastewater contains compounds that can pollute the environment. A design of domestic and laboratory wastewater treatment system is conducted. The system comprises of a neutralization tank, a grease trap, an equalization tank, an anaerobic filter, and an activated carbon and silica sand filter. The steps of the design are (i) collecting primary data and secondary data, (ii) calculating the engineering design, (iii) drawing the Detailed Engineering Design (DED), and (iv) calculating the bill of quantity and budget. The conclusion of this design is that the treatment plant will treat a mixture of domestic and laboratory wastewater. The dimension of each unit is as follows: (i) the neutralization tank (Ø = 0.65 m, H = 0.43 m), (ii) the grease trap (4 m x 2 m x 1 m), (iii) the equalization tank (10.5 m x 5.5 m x 2.5 m), (iv) the septic tank (4.5 m x 4 m x 2.5 m), (v) the six-compartment anaerobic filter (2.25 m x 4 m x 2.5 m), and (vi) the filter with activated carbon (H = 50 cm), silica sand (H = 150 cm), and gravel (H = 10 cm), with the diameter of the tank is 1.5 m.

The area of the campus of Institut Teknologi Sepuluh Nopember (ITS) and its housing complex are usually inundated during heavy rain. It is because the slope of the land in the campus generally flat. Moreover, it is because some of the drainage channels contain sediment that reduce the optimum capacity of the channels. Hence, an evaluation of the drainage system of ITS needs to be conducted. The steps of doing this evaluation are (i) identification of the existing problems, (ii) collection of primary and secondary data, (iii) literature review, (iv) calculation of capacity of the existing channels, (v) calculation of runoff, and (vi) analysis of the existing retention ponds. The primary data includes flow direction, the slope of channels, dimension of channels, and thickness of sediment in the channels. The secondary data comprises of rainfall intensity, Master Plan of ITS, and land-use. The calculation includes engineering design, bill of quantity (BOQ), and budget. A standard operation procedure for maintenance of drainage system to make the channels optimum is also suggested. From the analysis, it is shown that the maximum daily rainfalls are 136.09 mm/day for 5 year-rainfall return period and 159.19 mm/day for 10 year-rainfall return period. The cause of inundation in ITS is there are some channels which are not connected to each other. As a result, the drainage water cannot flow easily to receiving water body (river). Another cause of inundation is the slope of some channels that does not properly made. The inundation of some roads is because there are no street inlets such that the water could not flow to the side channels. It can be concluded that (i) it needs some addition of secondary channels and box culvert in some areas, (ii) the slope of some channels need to be rearranged, (iii) 288 street inlets must be constructed along the planning area.

PENETAPAN HARGA BERBASIS PENERIMAAN KONSUMENDI DUAL-CHANNEL SUPPLY CHAINERWIN WIDODOJurusan Teknik Industri, Institut Teknologi Sepuluh Nopember (ITS) SurabayaKampus ITS, Sukolilo, Surabaya 60111Surel: erwin@ie.its.ac.idABSTRAKDual-Channel Supply Chain (DCSC) adalah sebuah struktur gabungan yang secara simultanmemanfaatkan online dan offline channel untuk mendistribusikan sebuah produk. Struktur ini menjanjikanperluasan jangkauan pasar yang berujung pada peningkatan pendapatan. Meskipun demikian, selainmenawarkan potensi, DCSC juga membawa beberapa problem. Salah satu problem yang dominan adalahpenetapan harga harga antar channel. Pada prakteknya, para pelaku DCSC seringkali secara intuitifmenetapkan harga online dan offline-nya. Belum ada sebuah mekanisme pengukuran yang representatifuntuk problem yang sebenarnya sangat penting ini. Paper ini mencoba menjawab tantangan tersebutdengan mengusulkan sebuah mekanisme estimasi pengukuran secara kuantitatif tentang penerimaanpelanggan terhadap online channel relatif terhadap offline channel. Pendekatan yang diusulkan adalahpemanfaatan model matematis tentang hubungan interplay antar harga online dan offline. Parameterpenting yang menjadi perhatian utama adalah sebuah rasio penerimaan pelanggan kepada online channelrelatif terhadap offline channel. Parameter ini diukur dari 3 kelompok produk yang dijual dalam strukturDCSC yang ada di Indonesia guna menunjukkan perbedaan karakteristik dari masing-masing kelompokproduk tersebut. Hasil percobaan numerik yang dilakukan menunjukkan bahwa pemanfaatan usulanmekanisme penetapan harga ini dapat meningkatkan performansi finansial DCSC amatan.Kata kunci: dual-channel supply chain, penetapan harga, online channel, offline channelABSTRACTDual-Channel Supply Chain (DCSC) is a mixed structure which simultaneously utilizes both offline andonline channel to distribute one particular product or service. This structure provides market reach extensionin which eventually leads to revenue increase. Whatsoever, aside of this advantage, DCSC also brings somechallenging problems. One prominent problem is of about between-channel pricing-problem. In its practice,DCSC actors often apply intuitive offline and online pricing without further analytical evaluation. Yet there isno representative mechanism to address this critical problem. This paper attempts to resolute this challengeby proposing a qualitative estimation mechanism on customer acceptance on online channel relative tooffline one. This proposed approach is about to utilize an interplay relationship between offline and onlineprices. The main parameter to consider is a ratio of customer acceptance parameters. These parameters areelicited from 3 groups of products which are sold under DCSC structure in Indonesian cases to exhibit thedifferent properties in each product group. Numerical experiment result shows that the utilization of thispricing mechanism may increase the financial performance of DCSC under observation.Key words: dual-channel supply chain, pricing, online channel, offline channel