Artigos de revistas: "Extension de flamme"

1

Kibrya, M. G., e G. A. Karim. "Blowout Limits of a Jet Diffusion Flame in the Presence of Small Surrounding Jet Pilot Flames". Journal of Energy Resources Technology 118, n.º 2 (1 de junho de 1996): 140–44. http://dx.doi.org/10.1115/1.2792705.

Texto completo da fonte

Resumo:

The blowout limit of a methane jet diffusion flame is examined in the presence of a number of much smaller pilot jet flames of different fuels arranged within an experimental burner assembly in a co-flowing stream of air. It is shown that the blowout limit of the central jet flame can be extended very appreciably by increasing the flow rate through the smaller pilot jets. The basis for this extension to the blowout limit and the role of some changes in the operating parameters are discussed. It is suggested that the extension to the blowout limit observed is due mainly to the thermal contribution of the pilot jet flames.

Estilos ABNT, Harvard, Vancouver, APA, etc.

2

Yedinak, Kara M., Jack D. Cohen, Jason M. Forthofer e Mark A. Finney. "An examination of flame shape related to convection heat transfer in deep-fuel beds". International Journal of Wildland Fire 19, n.º 2 (2010): 171. http://dx.doi.org/10.1071/wf07143.

Texto completo da fonte

Resumo:

Fire spread through a fuel bed produces an observable curved combustion interface. This shape has been schematically represented largely without consideration for fire spread processes. The shape and dynamics of the flame profile within the fuel bed likely reflect the mechanisms of heat transfer necessary for the pre-heating and ignition of the fuel during fire spread. We developed a simple laminar flame model for examining convection heat transfer as a potentially significant fire spread process. The flame model produced a flame profile qualitatively comparable to experimental flames and similar to the combustion interface of spreading fires. The model comparison to flame experiments revealed that at increasing fuel depths (>0.7 m), lateral flame extension was increased through transition and turbulent flame behaviour. Given previous research indicating that radiation is not sufficient for fire spread, this research suggests that flame turbulence can produce the convection heat transfer (i.e. flame contact) necessary for fire spread particularly in vertically arranged, discontinuous fuels such as shrub and tree canopies.

Estilos ABNT, Harvard, Vancouver, APA, etc.

3

F. Ganji, Hamed, Viktor Kornilov, Philip de Goey, Ines Lopez Arteaga e Jeroen van Oijen. "Characterization and Identification of Thermoacoustic behaviour of flames anchored on burner decks with multiple perforation; Transfer Function (de)composition approach". INTER-NOISE and NOISE-CON Congress and Conference Proceedings 265, n.º 4 (1 de fevereiro de 2023): 3609–20. http://dx.doi.org/10.3397/in_2022_0508.

Texto completo da fonte

Resumo:

The appearance of thermoacoustic instability in combustion systems depends on thermoacoustic property (e.g., Transfer Function (TF)) of used burner/flame. Therefore, an attractive approach to cope with the instability is the purposeful design of the burner thermo-acoustics. One of the ideas of how the flame TF can be altered/designed is based on the heuristic idea that the acoustic response of one flame can be counteracted by the appropriately phased response of another flame. For the particular case of premixed, burner deck anchored conical flames, the TF depends on the diameter of perforation. It suggests the concept of combining different size and shape of perforations in one burner deck. In the present work, the acoustic response of sintered ceramic fibre burners with mixed perforation is investigated using the TF (de)-composition principle. By this approach, the cumulative flame TF can be represented as a weighted sum of elemental TF's of the groups of flames on the basis of the additive nature of the individual flame heat release rate. The capability of this principal to offer a designing framework for optimization of burner deck patterns aiming desirable acoustic characteristics will be tested by a course of measurements. Possible simplifications and extensions of the TF (de)composition principle will be discussed.

Estilos ABNT, Harvard, Vancouver, APA, etc.

4

Blunsdon, C. A., Z. Beeri, W. M. G. Malalasekera e J. C. Dent. "Comprehensive Modeling of Turbulent Flames With the Coherent Flame-Sheet Model—Part I: Buoyant Diffusion Flames". Journal of Energy Resources Technology 118, n.º 1 (1 de março de 1996): 65–71. http://dx.doi.org/10.1115/1.2792695.

Texto completo da fonte

Resumo:

A modified version of the computational fluid dynamics code KIVA-II was used to model the transient behavior of buoyant turbulent diffusion flames burning in still air. Besides extensions to the range of permitted boundary conditions and the addition of buoyancy terms to the turbulence model, KIVA-II was augmented by a version of the coherent flame-sheet model, Tesner’s soot generation model, Magnussen’s soot oxidation model, and an implementation of the discrete transfer radiation model that included both banded and continuum radiation. The model captured many of the features of buoyant turbulent flames. Its predictions supported experimental observations regarding the presence and frequency of large-scale pulsations, and regarding axial distributions of temperature, velocity, and chemical species concentrations. The radial structure of the flame was less well represented. The axial radiative heat flux distribution from the flame highlighted deficiencies in the soot generation model, suggesting that a model of soot particle growth was required.

Estilos ABNT, Harvard, Vancouver, APA, etc.

5

Obando Vega, Pedro Javier, Axel Coussement, Amsini Sadiki e Alessandro Parente. "Non-Premixed Filtered Tabulated Chemistry: Filtered Flame Modeling of Diffusion Flames". Fuels 2, n.º 2 (25 de março de 2021): 87–107. http://dx.doi.org/10.3390/fuels2020006.

Texto completo da fonte

Resumo:

The flame front filtering is a well-known strategy in turbulent premixed combustion. An extension of this approach for the non-premixed combustion context has been proposed by means of directly filtering counterflow diffusion flamelets. Promising results were obtained for the non-premixed filtered tabulated chemistry formalism on 1-D and 2-D unresolved counterflow flame configurations. The present paper demonstrates the soundness of this approach on a 3-D real laminar non-premixed coflow flame. The model results are compared against the direct filtering of the fully resolved laminar diffusion flame showing that the formalism adequately describes the underlying physics. The study reveals the importance of the one-dimensional counterflow flamelet hypothesis, so that the model activation under this condition is ensured by means of a flame sensor. The consistent coupling between the model and the flame sensor adequately retrieves the flame lift-off and satisfactorily predicts the profile extension due to the filtering process.

Estilos ABNT, Harvard, Vancouver, APA, etc.

6

Albayrak, Alp, e Wolfgang Polifke. "An analytical model based on the G-equation for the response of technically premixed flames to perturbations of equivalence ratio". International Journal of Spray and Combustion Dynamics 10, n.º 2 (22 de novembro de 2017): 103–10. http://dx.doi.org/10.1177/1756827717740776.

Texto completo da fonte

Resumo:

A model for the response of technically premixed flames to equivalence ratio perturbations is proposed. The formulation, which is an extension of an analytical flame tracking model based on the linearized G-equation, considers the flame impulse response to a local, impulsive, infinitesimal perturbation that is transported by convection from the flame base towards the flame surface. It is shown that the contributions of laminar flame speed and heat of reaction to the impulse response exhibit a local behavior, i.e. the flame responds at the moment when and at the location where the equivalence ratio perturbation reaches the flame surface. The time lag of this process is related to a convective time scale, which corresponds to the convective transport of fuel from the base of the flame to the flame surface. On the contrary, the flame surface area contribution exhibits a non-local behavior: albeit fluctuations of the flame shape are generated locally due to a distortion of the kinematic balance between flame speed and the flow velocity, the resulting wrinkles in flame shape are then transported by convection towards the flame tip with the restorative time scale. The impact of radial non-uniformity in equivalence ratio perturbations on the flame impulse response is demonstrated by comparing the impulse responses for uniform and parabolic radial profiles. Considerable deviation in the phase of the flame transfer function, which is important for thermo-acoustic stability, is observed.

Estilos ABNT, Harvard, Vancouver, APA, etc.

7

Tornatore, Cinzia, e Magnus Sjöberg. "Optical Investigation of a Partial Fuel Stratification Strategy to Stabilize Overall Lean Operation of a DISI Engine Fueled with Gasoline and E30". Energies 14, n.º 2 (12 de janeiro de 2021): 396. http://dx.doi.org/10.3390/en14020396.

Texto completo da fonte

Resumo:

This paper offers new insights into a partial fuel stratification (PFS) combustion strategy that has proven to be effective at stabilizing overall lean combustion in direct injection spark ignition engines. To this aim, high spatial and temporal resolution optical diagnostics were applied in an optically accessible engine working in PFS mode for two fuels and two different durations of pilot injection at the time of spark: 210 µs and 330 µs for E30 (gasoline blended with ethanol by 30% volume fraction) and gasoline, respectively. In both conditions, early injections during the intake stroke were used to generate a well-mixed lean background. The results were compared to rich, stoichiometric and lean well-mixed combustion with different spark timings. In the PFS combustion process, it was possible to detect a non-spherical and highly wrinkled blue flame, coupled with yellow diffusive flames due to the combustion of rich zones near the spark plug. The initial flame spread for both PFS cases was faster compared to any of the well-mixed cases (lean, stoichiometric and rich), suggesting that the flame propagation for PFS is enhanced by both enrichment and enhanced local turbulence caused by the pilot injection. Different spray evolutions for the two pilot injection durations were found to strongly influence the flame kernel inception and propagation. PFS with pilot durations of 210 µs and 330 µs showed some differences in terms of shapes of the flame front and in terms of extension of diffusive flames. Yet, both cases were highly repeatable.

Estilos ABNT, Harvard, Vancouver, APA, etc.

8

Haubold, Thorben Sören, Laura Puchot, Antoine Adjaoud, Pierre Verge e Katharina Koschek. "Bio-Based Bisbenzoxazines with Flame Retardant Linker". Polymers 13, n.º 24 (10 de dezembro de 2021): 4330. http://dx.doi.org/10.3390/polym13244330.

Texto completo da fonte

Resumo:

This work explores the strategy of incorporating a highly substituted reactive flame retardant into a benzoxazine moiety. For this purpose, a DOPO-based flame retardant received a chain extension via reaction with ethylene carbonate. It was then reacted with phloretic acid to obtain a diphenol end-capped molecule, and further reacted with furfurylamine and paraformaldehyde to obtain a benzoxazine monomer via a Mannich-like ring closure reaction. This four-step synthesis yielded a partly bio-based halogen-free flame retardant benzoxazine monomer (DOPO-PA-fa). The successful synthesis was proven via NMR, IR and MS analysis. The polymerization behavior was monitored by DSC and rheological analysis both showing the polymerization starts at 200 °C to yield pDOPO-PA-fa. pDOPO-PA-fa has a significant thermal stability with a residual mass of 30% at 800 °C under ambient atmosphere. Furthermore, it reached a V-0 rating against small flames and an OI of 35%. Blended with other benzoxazines, it significantly improves their thermal stability and fire resistance. It emphasizes its potential as flame retardant agent.

Estilos ABNT, Harvard, Vancouver, APA, etc.

9

Li, Linjie, Wuchao Zhang, Zihe Gao e Liangwen Wei. "Experimental study on the flame merging and ceiling impingement behavior of transversely located double fire sources in an urban utility tunnel". Indoor and Built Environment 32, n.º 1 (janeiro de 2023): 286–95. http://dx.doi.org/10.1177/1420326x221147427.

Texto completo da fonte

Resumo:

The investigation of the fire characteristics and propagation behaviour in the urban utility tunnel is of great practical importance, especially for the conditions with double fire sources. In this work, a 1/8th scaled urban utility tunnel model was built to conduct the experiments to characterize the flame merging and ceiling impingement behaviour of transversely located double fire sources. Two rectangular fire sources with the same dimension were used, and their heat release rate (HRR) and fire source spacings were varied to consider the typical scenarios. Results show that for the smaller HRR, the tunnel ceiling and sidewalls have little influence on the flame merging of double fire sources. With the increase of HRR, the flame gradually impinges on the tunnel ceiling and forms a stable ceiling jet flame extension, and the ceiling and sidewalls of the tunnel can promote the merging of the flames of the double fire sources. Besides, with the increase of the fire source spacings, the flame merging probability P m can be divided into three stages, that is, (i) complete merging stage, (ii) intermittent merging stage and (iii) complete separation stage. On this basis, the predicting relation of P m was obtained by using the piecewise function.

Estilos ABNT, Harvard, Vancouver, APA, etc.

10

Palacios, A., W. García e B. Rengel. "Flame shapes and thermal fluxes for an extensive range of horizontal jet flames". Fuel 279 (novembro de 2020): 118328. http://dx.doi.org/10.1016/j.fuel.2020.118328.

Texto completo da fonte

Estilos ABNT, Harvard, Vancouver, APA, etc.

11

Wu, Gang, Jinqing Li, Chunpeng Chai, Zhen Ge, Jialun Lin e Yunjun Luo. "Synthesis and characterization of novel post-chain extension flame retardant waterborne polyurethane". RSC Advances 5, n.º 118 (2015): 97710–19. http://dx.doi.org/10.1039/c5ra12975c.

Texto completo da fonte

Estilos ABNT, Harvard, Vancouver, APA, etc.

12

Avrin, Joel D. "Behaviour at ±∞ for a model of laminar flames with applications to questions of flame propagation versus extinction". Proceedings of the Royal Society of Edinburgh: Section A Mathematics 117, n.º 1-2 (1991): 103–8. http://dx.doi.org/10.1017/s0308210500027633.

Texto completo da fonte

Resumo:

SynopsisWe consider the behaviour at x = ±∞ of solutions to reaction-diffusion equations modelling laminar flames in a premixed reactive gas. We show that if the initial data have limits at ±∞, then the solutions satisfy ODEs at ±∞ for all positive time. We then analyse the qualitative behaviour of solutions to the ODEs. Our applications include extensions of previous results on questions of flame propagation versus extinction, and a new decay result: if the initial temperature is above ignition temperature at one end of the domani and if the initial concentration vanishes at the other, then we show that the concentration decays^to zero uniformly as the time variable goes to infinity.

Estilos ABNT, Harvard, Vancouver, APA, etc.

13

Cai, Jianan, Alvianto Wirasaputra, Yaming Zhu, Shumei Liu, Yubin Zhou, Chunhua Zhang e Jianqing Zhao. "The flame retardancy and rheological properties of PA6/MCA modified by DOPO-based chain extender". RSC Advances 7, n.º 32 (2017): 19593–603. http://dx.doi.org/10.1039/c6ra28293h.

Texto completo da fonte

Estilos ABNT, Harvard, Vancouver, APA, etc.

14

Vitz, Ed. "Demonstration Extensions: Flame Tests and Electrolysis". Journal of Chemical Education 85, n.º 4 (abril de 2008): 522. http://dx.doi.org/10.1021/ed085p522.1.

Texto completo da fonte

Estilos ABNT, Harvard, Vancouver, APA, etc.

15

Huang, Ping, Shengtao Liu, Chunxiang Liu, Fuqiang Yang, Baihan Zhang e Longxing Yu. "Flame extension lengths beneath a double slope roof induced by gaseous fuel jet flame". Fuel 350 (outubro de 2023): 128891. http://dx.doi.org/10.1016/j.fuel.2023.128891.

Texto completo da fonte

Estilos ABNT, Harvard, Vancouver, APA, etc.

16

Liang, Tianxiang, Jianan Cai, Shumei Liu, Hualin Lai e Jianqing Zhao. "Chain Extension and Synergistic Flame-Retardant Effect of Aromatic Schiff Base Diepoxide on Polyamide 6/Aluminum Diethylphosphinate Composites". Materials 12, n.º 14 (10 de julho de 2019): 2217. http://dx.doi.org/10.3390/ma12142217.

Texto completo da fonte

Resumo:

A way to suppress the deterioration in mechanical properties of polyamide 6 (PA6) is required, especially with high loading of flame retardants in the matrix. In this study, a novel aromatic Schiff base diepoxide (DES) was synthesized. It exhibited an efficient chain extension effect on PA6 and a synergistic flame-retardant effect with aluminum diethylphosphinate (AlPi) for PA6. The PA6 composite with 16 wt.% AlPi only passed UL-94 V-0 rating at 1.6 mm thickness, while the combination of 1.5 wt.% DES with 13 wt.% AlPi induced PA6 to achieve a UL-94 V-0 rating at 0.8 mm thickness. The tensile, flexural, and Izod notched impact strengths were increased by 16.2%, 16.5%, and 24.9%, respectively, compared with those of V-0 flame-retarded PA6 composites with 16 wt.% AlPi. The flame-retarded mechanism of PA6/AlPi/DES was investigated by cone calorimetry and infrared characterization of the char residues and pyrolysis products. These results showed that DES had a synergistic effect with AlPi in condensed-phase flame retardation by promoting the production of aluminum phosphorus oxides and polyphosphates in the char residues.

Estilos ABNT, Harvard, Vancouver, APA, etc.

17

Wang, Aijuan, Brady Manescau, Khaled Chetehouna, Steve Rudz e Ludovic Lamoot. "Experimental study on the flame extension and risk analysis of a diffusion impinging flame in confined compartment". Journal of Fire Sciences 39, n.º 4 (17 de junho de 2021): 285–308. http://dx.doi.org/10.1177/07349041211015766.

Texto completo da fonte

Resumo:

In this work, an experimental investigation on a diffusion impinging flame in a confined compartment was performed. The objective was to study the influence of confinement on the behavior of a flame impinging the ceiling and to deduce the auto-ignition risk of the smoke produced in the confined compartment. For this, configurations with five confinement levels were constructed by the condition of windows and/or door in the compartment and the variation of the heat release rates was made between 0.5 and 18.6 kW. To evaluate the flame morphology and flame extension length, an image processing method based on the direct linear transformation algorithm and the fire segmentation algorithm was adopted. From the experimental data, it was shown that the heat release rate of 4.6 kW presents a critical value for the flame extension in confined configurations, which corresponds to the equivalence ratio of the enclosure greater than 1, highlighting an under-ventilated environment. In addition, an auto-ignition risk analysis of smoke with unburnt gas in the compartment was carried out. The concentration and temperature of these gases were compared to the lower flammability limits and the auto-ignition temperature. It was observed that there was auto-ignition risk of the smoke under the ceiling, especially in the confined compartment of equivalence ratio greater than 1. Under these conditions, it is possible to have a fire spread to another compartment.

Estilos ABNT, Harvard, Vancouver, APA, etc.

18

Majhool, Ahmed Abed Al-Kadhem. "LAMINAR FLAME SPEED MODEL AT THE INITIAL STAGE OF FORMATION DIFFUSION FLAME". Kufa Journal of Engineering 7, n.º 1 (5 de março de 2016): 1–14. http://dx.doi.org/10.30572/2018/kje/711220.

Texto completo da fonte

Resumo:

This work paid special attention on the laminar flame speed in a piloted methane-air in jet diffusion flame due to the strong nonlinearity of chemical reaction process where an extension for the unsteady laminar flamelet model is required. The purpose for doing that is set for two folds. The partial differential equations for solving the combustion model required the representation of laminar flame speed in it and the advanced combustion modeling which is promising step. The probability density function required the laminar flame speed to be modelled as a function in terms of the mixture fraction to perform the integration. The laminar flame speed model is discussed, and the results are compared with the experimental database with good accuracy. The model specifies the conditional laminar flame speed and the difference against the gas flow velocity.Â

Estilos ABNT, Harvard, Vancouver, APA, etc.

19

Polifke, W., P. Flohr e M. Brandt. "Modeling of Inhomogeneously Premixed Combustion With an Extended TFC Model". Journal of Engineering for Gas Turbines and Power 124, n.º 1 (1 de fevereiro de 2000): 58–65. http://dx.doi.org/10.1115/1.1394964.

Texto completo da fonte

Resumo:

In many practical applications, so-called premixed burners do not achieve perfect premixing of fuel and air. Instead, fuel injection pressure is limited, the permissible burner pressure drop is small and mixing lengths are curtailed to reduce the danger of flashback. Furthermore, internal or external piloting is frequently employed to improve combustion stability, while part-load operation often requires burner staging, where neighboring burners operate with unequal fuel/air equivalence ratios. In this report, an extension of the turbulent flame speed closure (TFC) model for highly turbulent premixed combustion is presented, which allows application of the model to the case of inhomogeneously premixed combustion. The extension is quite straightforward, i.e., the dependence of model parameters on mixture fraction is accounted for by providing appropriate lookup tables or functional relationships to the model. The model parameters determined in this way are adiabatic flame temperature, laminar flame speed and critical gradient. The model has been validated against a test case from the open literature and applied to an externally piloted industrial gas turbine burner with good success.

Estilos ABNT, Harvard, Vancouver, APA, etc.

20

Nicolai, H., L. Dressler, J. Janicka e C. Hasse. "Assessing the importance of differential diffusion in stratified hydrogen–methane flames using extended flamelet tabulation approaches". Physics of Fluids 34, n.º 8 (agosto de 2022): 085118. http://dx.doi.org/10.1063/5.0102675.

Texto completo da fonte

Resumo:

Taking into account detailed chemical kinetics and therefore allowing for a detailed representation of the flame's microstructure at reduced computational cost make flamelet-based tabulation approaches such as the flamelet-generated manifold (FGM) a commonly used method for turbulent combustion simulations. However, there has been little focus on analyzing such models for fuel blends, including hydrogen. One reason for that is the challenging inclusion of differential diffusion effects into FGM, which may become crucial for highly diffusive fuels such as hydrogen. This paper presents an extension of the FGM approach that takes into account differential diffusion to assess the importance of differential diffusion for methane hydrogen blends. To this end, an extended model containing five controlling variables can be derived. However, the high correlation of certain controlling variables and the number of control variables could be reduced to three controlling variables in this study. These models are coupled to the artificially thickened flame (ATF) approach to facilitate large-eddy simulations (LESs). To ensure the consistency of the coupling between FGM and ATF when differential diffusion is considered, the model is thoroughly verified and validated using freely propagating and stratified laminar one-dimensional flames. Finally, simulations of the turbulent premixed stratified burner operated with a hydrogen methane blend are performed. The validation of the modeling framework is performed by comparing the simulation results to extensive experimental data, allowing an in-depth analysis of the macro- and microstructure of the flame.

Estilos ABNT, Harvard, Vancouver, APA, etc.

21

Kamal, MM. "Combustion via multiple pairs of opposing premixed flames with a cross-flow". Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy 231, n.º 1 (7 de outubro de 2016): 39–58. http://dx.doi.org/10.1177/0957650916673256.

Texto completo da fonte

Resumo:

A cylindrical burner accommodating stoichiometric fuel–air mixture combustion via multiple pairs of opposing jets and a cross-flow provided heat intensification and duplication of the stagnation impact for extending the firing limits and maximizing the power density. Six pairs of circumferentially opposing stoichiometric mixture jets sustained bulk injection velocities as high as 21.8 m/s and were associated with NOx emissions of 22 ppm, while emissions of 10 ppm were recorded upon reaching a lean limit equivalence ratio of 0.59. A stoichiometric mixture jet issuing perpendicular to the opposing jets at a momentum flux ratio of 0.3 increased the turbulence production rates to the extent that increased the maximum bulk injection velocity to 28.3 m/s and reduced the NOx emissions to 17 ppm. Since the recirculation zones between the two stagnation centers got compressed by increasing the momentum flux ratio to 0.8, the corresponding residence time reduction decreased the NOx emissions to 12 ppm. As the cross-flow mixture was made fuel–lean, dilution of the stoichiometric mixture by the fuel–lean mixture combustion products made it possible to get NOx emissions of single digit ppm. Emissions of 9 ppm resulted from using the cross-flow fuel–lean mixture jet due to compromising the flame stability limit extension and the temperature reduction in the post flame region. Such emissions, in turn, decreased to 4 ppm as the momentum flux ratio increased to 1.7 at which the stoichiometric mixture flames shrank into their ports. A minimum NOx emission index of 0.27 g/kg fuel was thus obtained at a volumetric heat release of 50.4 MW/m3. The momentum flux ratio corresponding to merging the two stagnation zones was correlated with Reynolds and Froude numbers, the jets’ separation as well as the density and viscosity values pertaining to the lean and stoichiometric mixtures’ flame temperatures.

Estilos ABNT, Harvard, Vancouver, APA, etc.

22

Wu, Gang, Jinqing Li e Yunjun Luo. "Flame retardancy and thermal degradation mechanism of a novel post-chain extension flame retardant waterborne polyurethane". Polymer Degradation and Stability 123 (janeiro de 2016): 36–46. http://dx.doi.org/10.1016/j.polymdegradstab.2015.11.004.

Texto completo da fonte

Estilos ABNT, Harvard, Vancouver, APA, etc.

23

Peters, N. "A spectral closure for premixed turbulent combustion in the flamelet regime". Journal of Fluid Mechanics 242 (setembro de 1992): 611–29. http://dx.doi.org/10.1017/s0022112092002519.

Texto completo da fonte

Resumo:

Premixed turbulent combustion in the flamelet regime is analysed on the basis of a field equation. This equation describes the instantaneous flame contour as an isoscalar surface of the scalar field G(x,t). The field equation contains the laminar burning velocity sL as velocity scale and its extension includes the effect of flame stretch involving the Markstein length [Lscr ] as a characteristic lengthscale of the order of the flame thickness. The scalar G(x,t) plays a similar role for premixed flamelet combustion as the mixture fraction Z(x,t) in the theory of non-premixed flamelet combustion.Equations for the mean $\overline{G}$ and variance $\overline{G^{\prime 2}}$ are derived. Additional closure problems arise for the mean source terms in these equations. In order to understand the nature of these terms an ensemble of premixed flamelets with arbitrary initial conditions in constant-density homogeneous isotropic turbulence is considered. An equation for the two-point correlation $\overline{G^{\prime}({\boldmath x},t)G^{\prime}({\boldmath x}+{\boldmath r},t)}$ is derived. When this equation is transformed into spectral space, closure approximations based on the assumption of locality and on dimensional analysis are introduced. This leads to a linear equation for the scalar spectrum function Γ(k,t), which can be solved analytically. The solution Γ(k,t) is analysed by assuming a small-wavenumber cutoff at k0 = lT−1, where lT is the integral lengthscale of turbulence. There exists a $k^{-\frac{5}{3}}$ spectrum between lT and LG, where LG is the Gibson scale. At this scale turbulent fluctuations of the scalar field G(x,t) are kinematically restored by the smoothing effect of laminar flame propagation. A quantity called kinematic restoration ω is introduced, which plays a role similar to the scalar dissipation χ for diffusive scalars.By calculating the appropriate moments of Γ(k,t), an algebraic relation between ω, $\omega,\overline{G^{\prime}({\boldmath x},t)^2}$, the integral lengthscale lT and the viscous dissipation ε is derived. Furthermore, the scalar dissipation χ[Lscr ], based on the Markstein diffusivity [Dscr ][Lscr ] = sL [Lscr ], and the scalar-strain co-variance Σ[Lscr ] are related to ω. Dimensional analysis, again, leads to a closure of the main source term in the equation for the mean scalar $\overline{G}$. For the case of plane normal and oblique turbulent flames the turbulent burning velocity sT and the flame shape is calculated. In the absence of flame stretch the linear relation sT ∼ u′ is recovered. The flame brush thickness is of the order of the integral lengthscale. In the case of a V-shaped flame its increase with downstream position is calculated.

Estilos ABNT, Harvard, Vancouver, APA, etc.

24

Ghorashi, Seyed Amin, Seyed Mohammad Hashemi, Seyed Abdolmehdi Hashemi e Mahdi Mollamahdi. "Numerical study on the combustion characteristics in a porous-free flame burner for lean mixtures". Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science 234, n.º 4 (9 de novembro de 2019): 935–45. http://dx.doi.org/10.1177/0954406219884979.

Texto completo da fonte

Resumo:

The present work implements a numerical simulation to investigate the combustion process in a porous-free flame burner. The non-equilibrium thermal condition is performed, and discretization and solving of the governing equations are conducted in a two-dimensional axisymmetric model. In order to simulate the combustion process, a reduced chemical kinetic mechanism of GRI 3.0, which includes 16 species and 41 reactions, is used. In order to prove the precision of the numerical method, some experimental tests are carried out and the numerical results are in a good agreement with the experimental measurements. The numerical results demonstrate that the porous-free flame burner has a higher flame stability compared to the conventional porous burner and the radiative efficiency of the porous-free flame burner is less than the porous burner. In addition, an increase in thermal conduction of the porous medium leads to an extension in the flame stability. In addition, the results show that with decreasing the pore density of porous medium, the flame stability is extended.

Estilos ABNT, Harvard, Vancouver, APA, etc.

25

CHAN, Simon Sze Man, Shuichi TORII e Toshiaki YANO. "Extension of Turbulent Jet Diffusion Flame Blowoff Limits by Doublet Flows." Transactions of the Japan Society of Mechanical Engineers Series B 67, n.º 663 (2001): 2841–47. http://dx.doi.org/10.1299/kikaib.67.2841.

Texto completo da fonte

Estilos ABNT, Harvard, Vancouver, APA, etc.

26

Wirasaputra, Alvianto, Lijun Zheng, Shumei Liu, Yanchao Yuan e Jianqing Zhao. "High-Performance Flame-Retarded Polyamide-6 Composite Fabricated by Chain Extension". Macromolecular Materials and Engineering 301, n.º 5 (11 de fevereiro de 2016): 614–24. http://dx.doi.org/10.1002/mame.201500357.

Texto completo da fonte

Estilos ABNT, Harvard, Vancouver, APA, etc.

27

Kolla, H., e N. Swaminathan. "Influence of Turbulent Scalar Mixing Physics on Premixed Flame Propagation". Journal of Combustion 2011 (2011): 1–8. http://dx.doi.org/10.1155/2011/451351.

Texto completo da fonte

Resumo:

The influence of reactive scalar mixing physics on turbulent premixed flame propagation is studied, within the framework of turbulent flame speed modelling, by comparing predictive ability of two algebraic flame speed models: one that includes all relevant physics and the other ignoring dilatation effects on reactive scalar mixing. This study is an extension of a previous work analysing and validating the former model. The latter is obtained by neglecting modelling terms that include dilatation effects: a direct effect because of density change across the flame front and an indirect effect due to dilatation on turbulence-scalar interaction. An analysis of the limiting behaviour shows that neglecting the indirect effect alters the flame speed scaling considerably when is small and the scaling remains unaffected when is large. This is evident from comparisons of the two models with experimental data which show that the quantitative difference between the two models is as high as 66% at but only 4% at . Furthermore, neglecting the direct effect results in a poor prediction of turbulent flame speed for all values of , and both effects are important for practically relevant values of this velocity ratio.

Estilos ABNT, Harvard, Vancouver, APA, etc.

28

Sacomano Filho, Fernando Luiz, Louis Dressler, Arash Hosseinzadeh, Amsini Sadiki e Guenther Carlos Krieger Filho. "Investigations of Evaporative Cooling and Turbulence Flame Interaction Modeling in Ethanol Turbulent Spray Combustion Using Tabulated Chemistry". Fluids 4, n.º 4 (31 de outubro de 2019): 187. http://dx.doi.org/10.3390/fluids4040187.

Texto completo da fonte

Resumo:

Evaporative cooling effects and turbulence flame interaction are analyzed in the large eddy simulation (LES) context for an ethanol turbulent spray flame. Investigations are conducted with the artificially thickened flame (ATF) approach coupled with an extension of the mixture adaptive thickening procedure to account for variations of enthalpy. Droplets are tracked in a Euler–Lagrangian framework, in which an evaporation model accounting for the inter-phase non-equilibrium is applied. The chemistry is tabulated following the flamelet generated manifold (FGM) method. Enthalpy variations are incorporated in the resulting FGM database in a universal fashion, which is not limited to the heat losses caused by evaporative cooling effects. The relevance of the evaporative cooling is evaluated with a typically applied setting for a flame surface wrinkling model. Using one of the resulting cases from the evaporative cooling analysis as a reference, the importance of the flame wrinkling modeling is studied. Besides its novelty, the completeness of the proposed modeling strategy allows a significant contribution to the understanding of the most relevant phenomena for the turbulent spray combustion modeling.

Estilos ABNT, Harvard, Vancouver, APA, etc.

29

Yu, Rixin. "Deep learning of nonlinear flame fronts development due to Darrieus–Landau instability". APL Machine Learning 1, n.º 2 (1 de junho de 2023): 026106. http://dx.doi.org/10.1063/5.0139857.

Texto completo da fonte

Resumo:

The Darrieus–Landau instability is studied using a data-driven, deep neural network approach. The task is set up to learn a time-advancement operator mapping any given flame front to a future time. A recurrent application of such an operator rolls out a long sequence of predicted flame fronts, and a learned operator is required to not only make accurate short-term predictions but also reproduce characteristic nonlinear behavior, such as fractal front structures and detached flame pockets. Using two datasets of flame front solutions obtained from a heavy-duty direct numerical simulation and a light-duty modeling equation, we compare the performance of three state-of-art operator-regression network methods: convolutional neural networks, Fourier neural operator (FNO), and deep operator network. We show that, for learning complicated front evolution, FNO gives the best recurrent predictions in both the short and long term. A consistent extension allowing the operator-regression networks to handle complicated flame front shape is achieved by representing the latter as an implicit curve.

Estilos ABNT, Harvard, Vancouver, APA, etc.

30

Resende, Pedro R., Leandro C. Morais, Carlos Pinho e Alexandre M. Afonso. "Combustion Characteristics of Premixed Hydrogen/Air in an Undulate Microchannel". Energies 15, n.º 2 (17 de janeiro de 2022): 626. http://dx.doi.org/10.3390/en15020626.

Texto completo da fonte

Resumo:

This work reports a numerical investigation of microcombustion in an undulate microchannel, using premixed hydrogen and air to understand the effect of the burner design on the flame in order to obtain stability of the flame. The simulations were performed for a fixed equivalence ratio and a hyperbolic temperature profile imposed at the microchannel walls in order to mimic the heat external losses occurred in experimental setups. Due to the complexity of the flow dynamics combined with the combustion behavior, the present study focuses on understanding the effect of the fuel inlet rate on the flame characteristics, keeping other parameters constant. The results presented stable flame structure regardless of the inlet velocity for this type of design, meaning that a significant reduction in the heat flux losses through the walls occurred, allowing the design of new simpler systems. The increase in inlet velocity increased the flame extension, with the flame being stretched along the microchannel. For higher velocities, flame separation was observed, with two detected different combustion zones, and the temperature profiles along the burner centerline presented a non-monotonic decrease due to the dynamics of the vortices observed in the convex regions of the undulated geometry walls. The geometry effects on the flame structure, flow field, thermal evolution and species distribution for different inlet velocities are reported and discussed.

Estilos ABNT, Harvard, Vancouver, APA, etc.

31

Yu, Xin, Zhen Cao, JiangBo Peng, Yang Yu, Guang Chang, Yufei Ma, XiaoHui Li, Chaobo Yang e ZhiQiang Wang. "Statistical Analysis of Flame Oscillation Characterization of Oxy-Fuel in Heavy Oil Boiler Using OH Planar Laser-Induced Fluorescence". Journal of Spectroscopy 2019 (2 de julho de 2019): 1–10. http://dx.doi.org/10.1155/2019/7085232.

Texto completo da fonte

Resumo:

The present work investigated the flame structures and oscillations of oxy-fuel combustions in a heavy oil boiler using OH planar laser-induced fluorescence imaging. Combustion instabilities, such as flame oscillation and combustion fluctuation, can assess the performance of an industrial burner in the boiler. The peak position variation in OH concentration was associated with the change of the reaction zone that corresponded with the fluctuation of the heat-release zone in the combustion chamber, which provides a valuable reference for the design of the combustion chamber. The experimental results suggest that the phenomenon of stratified flame combustion is related to the characteristic of flame oscillation. The substitution of N2 with CO2 will not significantly influence the flame oscillation frequency but increases the number of flame surface. As O2 concentration increased in the O2/CO2 atmosphere, the phenomenon of stratified flame combustion disappeared, and the flame presented an island-like structure. The bimodal oscillation of the combustion center was demonstrated by means of the probability density method; CO2 played a role in the extension of the combustion center. The combustion fluctuation of inner regions was quantitatively described; CO2 could maintain interregional stabilization to some extent. Compared with traditional measurement methods, PLIF technology has great advantages in evaluating burner performance and optimizing the design of the combustion chamber.

Estilos ABNT, Harvard, Vancouver, APA, etc.

32

Liu, Yuan Chao, Bao Min Sun e Zhao Yong Ding. "Influence Analysis of Sampling Time for Synthesis of Carbon Nanotubes in the V-Type Pyrolysis Flame". Advanced Materials Research 221 (março de 2011): 235–39. http://dx.doi.org/10.4028/www.scientific.net/amr.221.235.

Texto completo da fonte

Resumo:

Synthesis of carbon nanotubes from V-type pyrolysis flame is a kind of novel method. It needs simple laboratory equipments and normal atmosphere pressure. The V-type pyrolysis flame experimental system is introduced. Carbon source is the carbon monoxide and heat source is from acetylene/air premixed flame. Pentacarbonyl iron, served as catalyst, is transported by spray- pyrolysis method into the flame. The carbon nanotubes were characterized by scanning electron microscope and transmission electron microscope. This study aims to find the formation rule of carbon nanotubes from the V-type pyrolysis flame in different sampling times. The carbon nanotubes with less impurity and high yield were captured successfully in the V-type pyrolysis flame. The diameter of carbon nanotubes was approximate between 10nm and 20nm, and its length was dozens of microns. When the sampling time was below 3 minutes, the growth of carbon nanotubes came into the preparation growth period. The length of the carbon nanotubes increased gradually and the diameter had no obvious change with the extension of sampling time. When the sampling time was continued to the 5th minute, the growth of carbon nanotubes came into the exuberant growth period. The carbon nanotubes growth was finished within 5minutes. Longer sampling time was meaningless after the carbon nanotubes formation.

Estilos ABNT, Harvard, Vancouver, APA, etc.

33

Maeder, Xavier, Cees W. Passchier e Rudolph A. J. Trouw. "Flame foliation: Evidence for a schistosity formed normal to the extension direction". Journal of Structural Geology 29, n.º 3 (março de 2007): 378–84. http://dx.doi.org/10.1016/j.jsg.2006.10.005.

Texto completo da fonte

Estilos ABNT, Harvard, Vancouver, APA, etc.

34

Zhang, Xiaochun, Haowen Tao, Wenbin Xu, Xiaozhou Liu, Xianda Li, Xiaolei Zhang e Longhua Hu. "Flame extension lengths beneath an inclined ceiling induced by rectangular-source fires". Combustion and Flame 176 (fevereiro de 2017): 349–57. http://dx.doi.org/10.1016/j.combustflame.2016.11.004.

Texto completo da fonte

Estilos ABNT, Harvard, Vancouver, APA, etc.

35

Rossa, Carlos, e Paulo Fernandes. "An Empirical Model for the Effect of Wind on Fire Spread Rate". Fire 1, n.º 2 (1 de setembro de 2018): 31. http://dx.doi.org/10.3390/fire1020031.

Texto completo da fonte

Resumo:

Predicting wind-driven rate of fire spread (RoS) has been the aim of many studies. Still, a field-tested model for general use, regardless of vegetation type, is currently lacking. We develop an empirical model for wind-aided RoS from laboratory fires (n = 216), assuming that it depends mainly on fire-released energy and on the extension of flame over the fuel bed in still air, and that it can be obtained by multiplying RoS in no-wind and no-slope conditions by a factor quantifying the wind effect. Testing against independent laboratory and field data (n = 461) shows good agreement between observations and predictions. Our results suggest that the fuel bed density effect detected by other work may be a surrogate for the amount of fuel involved in combustion, which depends on fuel load. Because RoS under windless conditions is unaffected by fuel load, the involved mechanisms differ from wind-aided propagation. Compared to shallow fuel beds, the wind effect is usually modest in deep vegetation, because tall fuel complexes are dominated by live fuels (high moisture content) and flames extend less above the vegetation when fuel moisture is high. The present work warrants further inspection in a broader range of field conditions.

Estilos ABNT, Harvard, Vancouver, APA, etc.

36

Fossi, Alain, Alain DeChamplain e Benjamin Akih-Kumgeh. "Unsteady RANS and scale adaptive simulations of a turbulent spray flame in a swirled-stabilized gas turbine model combustor using tabulated chemistry". International Journal of Numerical Methods for Heat & Fluid Flow 25, n.º 5 (1 de junho de 2015): 1064–88. http://dx.doi.org/10.1108/hff-09-2014-0272.

Texto completo da fonte

Resumo:

Purpose – The purpose of this paper is to numerically investigate the three-dimensional (3D) reacting turbulent two-phase flow field of a scaled swirl-stabilized gas turbine combustor using the commercial computational fluid dynamic (CFD) software ANSYS FLUENT. The first scope of the study aims to explicitly compare the predictive capabilities of two turbulence models namely Unsteady Reynolds Averaged Navier-Stokes and Scale Adaptive Simulation for a reasonable trade-off between accuracy of results and global computational cost when applied to simulate swirl-stabilized spray combustion. The second scope of the study is to couple chemical reactions to the turbulent flow using a realistic chemistry model and also to model the local chemical non-equilibrium(NEQ) effects caused by turbulent strain such as flame stretching. Design/methodology/approach – Standard Eulerian and Lagrangian formulations are used to describe both gaseous and liquid phases, respectively. The computing method includes a two-way coupling in which phase properties and spray source terms are interchanging between the two phases within each coupling time step. The fuel used is liquid jet-A1 which is injected in the form of a polydisperse spray and the droplet evaporation rate is calculated using the infinite conductivity model. One-component (n-decane) and two-component fuels (n-decane+toluene) are used as jet-A1 surrogates. The combustion model is based on the mean mixture fraction and its variance, and a presumed-probability density function is used to model turbulent-chemistry interactions. The instantaneous thermochemical state necessary for the chemistry tabulation is determined by using initially the equilibrium (EQ) assumption and thereafter, detailed NEQ calculations through the steady flamelets concept. The combustion chemistry of these surrogates is represented through a reduced chemical kinetic mechanism (CKM) comprising 1,045 reactions among 139 species, derived from the detailed jet-A1 surrogate model, JetSurf 2.0 using a sensitivity based method, Alternate Species Elimination. Findings – Numerical results of the gas velocity, the gas temperature and the species molar fractions are compared with their experimental counterparts obtained from a steady state flame available in the literature. It is observed that, SAS coupled to the tabulated flamelet-based chemistry, predicts reasonably the main flame trends, while URANS even provided with the same combustion model and computing resources, leads to a poor prediction of the global flame trends, emphasizing the asset of a proper resolution when simulating spray flames. Research limitations/implications – The steady flamelet model even coupled with a robust turbulence model does not reproduce accurately the trend of species with slow oxidation kinetics such as CO and H2, because of the restrictiveness of the solutions space of flamelet equations and the assumption of unity Lewis for all species. Practical implications – This work is adding a contribution for spray flame modeling and can be seen as an extension to the significant efforts for the modeling of gaseous flames using robust turbulence models coupled with the tabulated flamelet-based chemistry approach to considerably reduce computing cost. The exclusive use of a commercial CFD code widely used in the industry allows a direct application of this simulation approach to industrial configurations while keeping computing cost reasonable. Originality/value – This study is useful to engineers interested in designing combustors of gas turbines and others combustion systems fed with liquid fuels.

Estilos ABNT, Harvard, Vancouver, APA, etc.

37

Zheng, Jiaxin, Congxiao Wang, Yuyin Zhao, Menghao Guo, Yadong He e Chunling Xin. "The Synergy of Nanosilica and Zinc Diethyl Hypophosphite Influences the Flame Retardancy and Foaming Performance of Poly(Ethylene Terephthalate)". Advances in Polymer Technology 2023 (28 de abril de 2023): 1–15. http://dx.doi.org/10.1155/2023/4319998.

Texto completo da fonte

Resumo:

In order to improve the flame retardancy of poly(ethylene terephthalate) (PET) and maintain its excellent foamability, nanosilica (nano-SiO2), and zinc diethyl hypophosphite (ZDP) were selected as synergistic flame retardants, and pyromellitic dianhydride (PMDA) was used as a chain extender to carry out flame retardant and chain extension modification of PET simultaneously. The flame retardancy and flame-retardant mechanism of modified PET were characterized by limiting oxygen index, vertical combustion test, thermogravimetric analysis, and SEM. Dynamic rheological test and DSC were used to analyze the rheological and thermal properties. The foaming ability was also studied by batch foaming experiments. The test results indicated that nano-SiO2 and ZDP had a synergistic effect, which could significantly improve flame retardancy of PET. The vertical combustible grade of modified PET reached V-0 grade, and the limiting oxygen index increased from 21% to about 30%. The role of nano-SiO2 on the flame retardancy of PET was mainly to increase compactness and strength of the carbon layer, which could block combustible gas produced by the pyrolysis of PET and resist dripping behavior. At the same time, the addition of nano-SiO2 increased the crystallization temperature and crystallinity of PET. Otherwise, nano-SiO2 could act as a bubble-nucleating agent and improve the foaming ability of modified PET. When the addition amount was 1 wt%, not only did the maximum foaming ratio increase but the foaming temperature zone was also widened from 225°C-235°C to 225°C-250°C. Finally, a flame-retardant PET system with good foaming property was proposed.

Estilos ABNT, Harvard, Vancouver, APA, etc.

38

Li, Jie, Hongtao Li, Chen Chen, Guannan Liu, Yaoyao Ying, Tianjiao Li e Dong Liu. "Edge Effects on Simultaneous Reconstructions of Flame Temperature and Soot Volume Fraction Profiles by a CCD Camera". Sensors 22, n.º 21 (26 de outubro de 2022): 8199. http://dx.doi.org/10.3390/s22218199.

Texto completo da fonte

Resumo:

In this paper, the influence of the edge effect on the simultaneous reconstruction of axisymmetric flame temperature and soot volume fraction profiles by a single CCD camera was investigated in detail. The reconstruction accuracy of the flame temperature profile and soot volume fraction was insensitive to the measurement error of the coefficient matrix. When the signal to ratio (SNR) of the measurement system for both the radiation intensity and coefficient matrix was as low as 46 dB, the reconstruction accuracy for both temperature and soot volume fraction was acceptable and was more influenced by the radiation intensity measurement error. The reconstruction of the flame temperature and soot volume fraction was greatly influenced by the edge effect. When the flame edge with weak radiation signals was ignored during the reconstruction, the relative reconstruction error for the temperature and soot volume fraction increased from the flame center to the edge, and reached an unacceptable value at the reconstruction boundary, especially for the soot volume fraction. The flame image boundary could be chosen as the unified reconstruction boundary to reconstruct the two-dimensional distribution of the temperature and soot volume fraction with satisfactory accuracy. The low soot volume fraction could influence the reconstruction accuracy for both the temperature and soot concentration in non-sooting regions. Moreover, there was no obvious regularity between the reconstruction accuracy of the temperature and soot volume fraction and the extension of the reconstruction boundary.

Estilos ABNT, Harvard, Vancouver, APA, etc.

39

Boyde, Jan M., Patrick C. Le Clercq, Massimiliano Di Domenico e Manfred Aigner. "Extension of the turbulent flame speed closure model to ignition in multiphase flows". Combustion and Flame 160, n.º 2 (fevereiro de 2013): 351–65. http://dx.doi.org/10.1016/j.combustflame.2012.10.006.

Texto completo da fonte

Estilos ABNT, Harvard, Vancouver, APA, etc.

40

Zhao, Wenbin, Fangshun Liu, Bo Liu, Yang Liu, Huaisheng Cao, Qing Tan e Jinfeng Wang. "Study on Permeability and Flame Retardancy of Coal Aerosol Atomized by Ultrasonic Wave". Atmosphere 13, n.º 9 (1 de setembro de 2022): 1415. http://dx.doi.org/10.3390/atmos13091415.

Texto completo da fonte

Resumo:

In order to analyze the permeability and particle size distribution of atomized aerosol in different coal particle sizes and to explore the inhibition performance of an atomized inhibitor in different atomization times and positions, the following conclusions are obtained by ultrasonic atomization device: The results of permeability experiment show that the particle size of aerosol decreases with the increase of atomization frequency. In addition, with the particle size of the coal sample decreasing from 5 cm to 0.6 cm, the penetration ratio of aerosol in coal decreases from 64.2% to 15.5% due to the interception of large particle size water mist by dense coal. The aerosol with a particle size of 2~4 μm has better permeability in crushed coal. The flame retardant experiment shows that compared with the raw coal, the aliphatic hydrocarbon of the atomized coal decreases by 75.9%, the aromatic hydrocarbon decreases by 57.5%, and the flame retardant effect is good. Meanwhile, the extension of solution atomization time will further enhance the flame retardant ability of ultrasonic atomized aerosol.

Estilos ABNT, Harvard, Vancouver, APA, etc.

41

Kim, Gyeong Taek, Gyeong Taek Kim, Hyun Seok You, Chun Sang Yoo, Jeong Park e Suk Ho Chung. "Extension of Lean Operation and Extinction Limit of Premixed Flame Applying Non-Thermal Plasma". Journal of The Korean Society of Combustion 24, n.º 1 (31 de março de 2019): 46–50. http://dx.doi.org/10.15231/jksc.2019.24.1.046.

Texto completo da fonte

Estilos ABNT, Harvard, Vancouver, APA, etc.

42

Torii, Shuichi. "Effect of Collar Length on Extension of Subsonic Hydrogen Jet Diffusion Flame Blowout Limits". International Journal of Green Energy 4, n.º 4 (31 de julho de 2007): 367–75. http://dx.doi.org/10.1080/15435070701332070.

Texto completo da fonte

Estilos ABNT, Harvard, Vancouver, APA, etc.

43

He, Di, Yusong Yu, Hao Ma, Hongbo Liang e Chaojun Wang. "Extensive Discussions of the Eddy Dissipation Concept Constants and Numerical Simulations of the Sandia Flame D". Applied Sciences 12, n.º 18 (13 de setembro de 2022): 9162. http://dx.doi.org/10.3390/app12189162.

Texto completo da fonte

Resumo:

The indisputable wide use of the Eddy Dissipation Concept (EDC) implies that the resulting mean reaction rate is reasonably well modeled. To model turbulent combustions, an amount of EDC constants that differ from the original values was proposed. However, most of them were used without following the nature of the model or considering the effects of the modification. Starting with the energy cascade and the EDC models, the exact original primary and secondary constants are deduced in detail in this work. The mean reaction rate is then formulated from the primary constants or the secondary constants. Based on the physical meaning of fine structures, the limits of the EDC constants are presented and can be used to direct the EDC constant modifications. The effects of the secondary constant on the mean reaction rate are presented and the limiting turbulence Reynolds number used for the validity of EDC is discussed. To show the effects of the constants of the EDC model on the mean reaction rate, 20 combinations of the primary constants are used to simulate a laboratory-scale turbulent jet flame, i.e., Sandia Flame D. After a thorough and careful comparison with experiments, case 8, with a secondary constant of 6 and primary constants of 0.1357 and 0.11, can aptly reproduce this flame, except for in the over-predicted mean OH mass fraction.

Estilos ABNT, Harvard, Vancouver, APA, etc.

44

Lee, Uen Do, Hyun Dong Shin, Kwang Chul Oh, Ki Ho Lee e Eui Ju Lee. "Extinction limit extension of unsteady counterflow diffusion flames affected by velocity change". Combustion and Flame 144, n.º 4 (março de 2006): 792–808. http://dx.doi.org/10.1016/j.combustflame.2005.09.013.

Texto completo da fonte

Estilos ABNT, Harvard, Vancouver, APA, etc.

45

Mahmoud, Rihab, Mehdi Jangi, Florian Ries, Benoit Fiorina, Johannes Janicka e Amsini Sadiki. "Combustion Characteristics of a Non-Premixed Oxy-Flame Applying a Hybrid Filtered Eulerian Stochastic Field/Flamelet Progress Variable Approach". Applied Sciences 9, n.º 7 (29 de março de 2019): 1320. http://dx.doi.org/10.3390/app9071320.

Texto completo da fonte

Resumo:

The oxidation of methane under oxy-fuel combustion conditions with carbon capture is attractive and deserves huge interest towards reducing CO2 and NOx emissions. The current paper reports on the predictions and analysis of combustion characteristics of a turbulent oxy-methane non-premixed flame operating under highly diluted conditions of CO2 and H2 in oxidizer and fuel streams, respectively. These are achieved by applying a novel, well-designed numerical combustion model. The latter consists of a large eddy simulation (LES) extension of a recently suggested hybrid model in Reynolds averaging-based numerical simulation (RANS) context by the authors. It combines a transported joint scalar probability density function (T-PDF) following the Eulerian Stochastic Field methodology (ESF) on the one hand, and a flamelet progress variable (FPV) turbulent combustion model under consideration of detailed chemical reaction mechanism on the other hand. This novel hybrid ESF/FPV approach removes the weaknesses of the presumed-probability density function (P-PDF)-based FPV modeling, along with the solving of associated additional modeled transport equations while rendering the T-PDF computationally less affordable. First, the prediction capability of the LES hybrid ESF/FPV was appraised on the well-known air-piloted methane jet flame (Sandia Flame D). Then, it was assessed in analyzing the combustion properties of a non-premixed oxy-flame and in capturing the CO2 dilution effect on the oxy-fuel flame behavior. To this end, the so-called oxy-flame B3, already numerically investigated in a RANS context, was analyzed. Comparisons with experimental data in terms of temperature, scalar distributions, and scatter plots agree satisfactorily. Finally, the impact of generating the FPV chemistry table under condition of unity Lewis number, even with CO2 dilution, was investigated on the general prediction of the oxy-fuel flame structure, stability and emissions. In particular, it turns out that 68% molar percentage of CO2 leads to 0.39% of CO formation near the burner fuel nozzle and 0.62% at 10 dfuel above the nozzle.

Estilos ABNT, Harvard, Vancouver, APA, etc.

46

Vilmart, Gautier, Nelly Dorval, Robin Devillers, Yves Fabignon, Brigitte Attal-Trétout e Alexandre Bresson. "Imaging Aluminum Particles in Solid-Propellant Flames Using 5 kHz LIF of Al Atoms". Materials 12, n.º 15 (29 de julho de 2019): 2421. http://dx.doi.org/10.3390/ma12152421.

Texto completo da fonte

Resumo:

Laser-induced fluorescence imaging of aluminum atoms (Al-PLIF) is used to analyze the spatio-temporal behavior of aluminized solid propellant combustion. Using alternating LIF and chemiluminescence emission images of the particles in the gaseous and liquid phase evolving close to and far above the dynamically varying propellant surface, sequences of images were recorded and analyzed. The good sensitivity achieved enabled us to track the dynamics of the flame in the vicinity of particles detected all along the flame extension and up to 1.5 MPa. Analysis of wide-field images enabled droplet velocity measurements due to the high LIF sampling rate (5 kHz). The observed typical plume structures were in good agreement with alumina-formation prediction and previous shadowgraphy visualization. High-resolution sequences of images showed gaseous distribution behavior around the molten particles. The Al vapor phase was thus found to extend between 3 and 6.5 radii around the particles. Particle detachment dynamics were captured just above the propellant surface.

Estilos ABNT, Harvard, Vancouver, APA, etc.

47

Liu, Peng, Jiandi Ling, Taoyan Mao, Feng Liu, Wenzhi Zhou, Guojie Zhang e Fengwei Xie. "Adhesive and Flame-Retardant Properties of Starch/Ca2+ Gels with Different Amylose Contents". Molecules 28, n.º 11 (4 de junho de 2023): 4543. http://dx.doi.org/10.3390/molecules28114543.

Texto completo da fonte

Resumo:

Starch, being renewable and biodegradable, is a viable resource for developing sustainable and environmentally friendly materials. The potential of starch/Ca2+ gels based on waxy corn starch (WCS), normal corn starch (NCS), and two high-amylose corn starches, G50 (55% amylose content) and G70 (68% amylose content) as flame-retardant adhesives has been explored. Being stored at 57% relative humidity (RH) for up to 30 days, the G50/Ca2+ and G70/Ca2+ gels were stable without water absorption or retrogradation. The starch gels with increasing amylose content displayed increased cohesion, as reflected by significantly higher tensile strength and fracture energy. All the four starch-based gels showed good adhesive properties on corrugated paper. For wooden boards, because of the slow diffusion of the gels, the adhesive abilities are weak initially but improve with storage extension. After storage, the adhesive abilities of the starch-based gels are essentially unchanged except for G70/Ca2+, which peels from a wood surface. Moreover, all the starch/Ca2+ gels exhibited excellent flame retardancy with limiting oxygen index (LOI) values all around 60. A facile method for the preparation of starch-based flame-retardant adhesives simply by gelating starch with a CaCl2 solution, which can be used in paper or wood products, has been demonstrated.

Estilos ABNT, Harvard, Vancouver, APA, etc.

48

Yun-yun, Chen, Li Zhen-hua, Song Yang e He An-zhi. "Extension of the Gladstone-Dale equation for flame flow field diagnosis by optical computerized tomography". Applied Optics 48, n.º 13 (24 de abril de 2009): 2485. http://dx.doi.org/10.1364/ao.48.002485.

Texto completo da fonte

Estilos ABNT, Harvard, Vancouver, APA, etc.

49

Wang, Zhenhua, Kuibin Zhou, Le Zhang, Xuan Nie, Yueqiong Wu, Juncheng Jiang, Anne Simone Dederichs e Lu He. "Flame extension area and temperature profile of horizontal jet fire impinging on a vertical plate". Process Safety and Environmental Protection 147 (março de 2021): 547–58. http://dx.doi.org/10.1016/j.psep.2020.11.028.

Texto completo da fonte

Estilos ABNT, Harvard, Vancouver, APA, etc.

50

UCHIDA, Tetsuo, Hirofumi ISOYAMA, Mariko TATEMATSU, Isao KOJIMA, Chuzo IIDA, Keisuke GOTO e Michio MATSUBARA. "Application of absolute amount measurement in flame AAS; Extension of linear range of calibration curve." Bunseki kagaku 37, n.º 12 (1988): T232—T237. http://dx.doi.org/10.2116/bunsekikagaku.37.12_t232.

Texto completo da fonte

Estilos ABNT, Harvard, Vancouver, APA, etc.

Artigos de revistas sobre o tema "Extension de flamme"

Crie uma referência precisa em APA, MLA, Chicago, Harvard, e outros estilos