Gotowa bibliografia na temat „Tungstene carbide”
Utwórz poprawne odniesienie w stylach APA, MLA, Chicago, Harvard i wielu innych
Spis treści
Zobacz listy aktualnych artykułów, książek, rozpraw, streszczeń i innych źródeł naukowych na temat „Tungstene carbide”.
Przycisk „Dodaj do bibliografii” jest dostępny obok każdej pracy w bibliografii. Użyj go – a my automatycznie utworzymy odniesienie bibliograficzne do wybranej pracy w stylu cytowania, którego potrzebujesz: APA, MLA, Harvard, Chicago, Vancouver itp.
Możesz również pobrać pełny tekst publikacji naukowej w formacie „.pdf” i przeczytać adnotację do pracy online, jeśli odpowiednie parametry są dostępne w metadanych.
Artykuły w czasopismach na temat "Tungstene carbide"
Idrees, Maria, Husnain Ahmad Chaudhary, Arslan Akbar, Abdeliazim Mustafa Mohamed i Dina Fathi. "Effect of Silicon Carbide and Tungsten Carbide on Concrete Composite". Materials 15, nr 6 (10.03.2022): 2061. http://dx.doi.org/10.3390/ma15062061.
Pełny tekst źródłaZhong, Li Sheng, Yun Hua Xu, Peng Yu, Xiao Jie Liu, Fang Xia Ye i Hong Hua Yan. "Microstructure and Abrasive Wear Characteristics of In Situ WC Bundles – Reinforced Iron Matrix Composites". Advanced Materials Research 284-286 (lipiec 2011): 265–68. http://dx.doi.org/10.4028/www.scientific.net/amr.284-286.265.
Pełny tekst źródłaPu, Juan, Yu-Bo Sun, Lei Wu, Peng He i Wei-Min Long. "Effect of CeO2 Content on Microstructure and Properties of Ni-Based Tungsten Carbide Layer by Plasma Arc Cladding". Coatings 12, nr 3 (6.03.2022): 342. http://dx.doi.org/10.3390/coatings12030342.
Pełny tekst źródłaNovoselova, Inessa, Serhii Kuleshov, Anatoliy Omel’chuk, Valerii Bykov i Olena Fesenko. "ELECTROREDUCTION OF DITUNGSTATE AND CARBONATE ANIONS IN CHLORIDE MELT". Ukrainian Chemistry Journal 87, nr 12 (21.01.2022): 97–108. http://dx.doi.org/10.33609/2708-129x.87.12.2021.97-108.
Pełny tekst źródłaGezerman, Ahmet Ozan, i Burcu Didem Çorbacıoğlu. "Effects of Mechanical Alloying on Sintering Behavior of Tungsten Carbide-Cobalt Hard Metal System". Advances in Materials Science and Engineering 2017 (2017): 1–11. http://dx.doi.org/10.1155/2017/8175034.
Pełny tekst źródłaLu, Hao, Chong Zhao, Haibin Wang, Xuemei Liu, Rong Yu i Xiaoyan Song. "Hardening tungsten carbide by alloying elements with high work function". Acta Crystallographica Section B Structural Science, Crystal Engineering and Materials 75, nr 6 (8.11.2019): 994–1002. http://dx.doi.org/10.1107/s2052520619012277.
Pełny tekst źródłaTarraste, Marek, Jakob Kübarsepp, Arvo Mere, Kristjan Juhani, Märt Kolnes i Mart Viljus. "Ultrafine Cemented Carbides with Cobalt and Iron Binders Prepared via Reactive In Situ Sintering". Solid State Phenomena 320 (30.06.2021): 176–80. http://dx.doi.org/10.4028/www.scientific.net/ssp.320.176.
Pełny tekst źródłaГорленко, Александр, Aleksandr Gorlenko, Сергей Давыдов i Sergey Davydov. "Material implantation techniques based on tungsten carbide to increase friction surface durability". Science intensive technologies in mechanical engineering 1, nr 9 (23.08.2016): 3–9. http://dx.doi.org/10.12737/21233.
Pełny tekst źródłaLima, Maria Jose S., M. V. M. Souto, A. S. Souza, M. M. Karimi, F. E. S. Silva, Uilame Umbelino Gomes i Carlson P. de Souza. "Synthesis of Nanostructured Tungsten Carbide (WC) from Ammonia Paratungstate-APT and its Characterization by XRD and Rietveld Refinement". Materials Science Forum 899 (lipiec 2017): 31–35. http://dx.doi.org/10.4028/www.scientific.net/msf.899.31.
Pełny tekst źródłaWu, Yung-Yi, i Dong-Yea Sheu. "Investigating Tungsten Carbide Micro-Hole Drilling Characteristics by Desktop Micro-ECM with NaOH Solution". Micromachines 9, nr 10 (11.10.2018): 512. http://dx.doi.org/10.3390/mi9100512.
Pełny tekst źródłaRozprawy doktorskie na temat "Tungstene carbide"
Roure, Sophie. "Densification des mélanges de poudres WC-Co : de la compression au frittage". Grenoble INPG, 1996. http://www.theses.fr/1996INPG0222.
Pełny tekst źródłaHarry, Emmanuelle. "Stabilité mécanique et modes d'endommagement de revêtements multicouches à base de tungstène et de tungstène-carbone élaborés par PVD". Grenoble INPG, 1998. http://www.theses.fr/1998INPG0071.
Pełny tekst źródłaLavergne, Olivier. "Mécanismes de dissolution et de précipitation dans les carbures cémentés WC/Co". Grenoble INPG, 1997. http://www.theses.fr/1997INPG0214.
Pełny tekst źródłaLindahl, Bonnie. "Equilibrium Study of Chromium Containing Cemented Carbides : Solubility of chromium in tungsten carbide and η-phase". Thesis, KTH, Materialvetenskap, 2010. http://urn.kb.se/resolve?urn=urn:nbn:se:kth:diva-49974.
Pełny tekst źródłaGuiz, Robin. "Influence d’additions de titane/tungstène et de vanadium sur la précipitation de carbures secondaires au sein d’alliages modèles de type HP". Thesis, Lyon, 2016. http://www.theses.fr/2016LYSEM011/document.
Pełny tekst źródłaHP alloys are typically used as steam methane reforming tubes in the petrochemical industry. During service, they are exposed to temperatures between 700°C and 1000°C under gaz pressure of several MPa. Their as-cast microstructure, together with fine in-situ secondary precipitation, provide these alloys with an excellent resistance to creep deformation. Nevertheless, after long-time ageing, coarsening of secondary carbides leads to the weakening of the tubes and therefore to an accelerated damaging.The effects of some alloying elements (V, Ti/W) on secondary precipitation of M23C6 and NbC carbides were investigated through numerical simulations performed with TC-PRISMA software. On the basis of encouraging results in terms of precipitation optimization, two model HP-type alloys were cast at the laboratory and aged in the range of temperatures corresponding to service conditions. As-cast microstructures were first compared with an industrial "standard" alloy. Then, secondary precipitation were characterized for all the alloys and all ageing temperatures. Microstructural investigation highlighted the beneficial effect of vanadium and titanium/tungsten additions on secondary precipitation characteristics
Agode, Kofi Edoh. "Analyse et modélisation du comportement à l’usure des outils de coupe en carbure de tungstène pour différentes teneurs en cobalt lors de l’usinage de l’alliage de titane Ti-6Al-4V". Electronic Thesis or Diss., Université de Lorraine, 2022. http://www.theses.fr/2022LORR0141.
Pełny tekst źródłaDue to their high hardness and wear resistance, cemented carbide (WC-Co) is the main material used to manufacture machining tools and forming tooling, as well as wear parts requiring high hardness and high precision. The modification of tungsten carbide microstructure, and more particularly its cobalt content, is currently attracting the greatest interest from manufacturers to develop new grades tools with high performance, and then expand new markets.This thesis aims to study the effect of the cobalt content of carbide tools on the measured values and wear mechanisms when machining hard superalloys such as the aeronautical titanium alloys Ti-6Al-4V. Both experimental and numerical research work are devoted on one hand to the understanding of the microscopic damage mechanisms leading to the macroscopic wear of the WC-Co composite and on the other hand, to the influence of the cobalt content on the behavior of the WC-Co taking into account the mechanical-microstructure-damage coupling.On the basis of an experimental analysis, the identification of the macroscopic and microscopic physical phenomena involved at the tool/chip and tool/workpiece contact interfaces was conducted. Machining tests were firstly carried out on the tool-material couple WC-Co/Ti-6Al-4V with different cobalt contents for the tools (from 6 to 15%). In a second step, a tribological characterization of the same tool-material couple was carried out to evaluate the influence of the cobalt content and the contact conditions (sliding speed, applied force) on the friction coefficient and wear. However, the inaccessibility of the contact zones during machining and the tribological tests did not allow a complete description of the wear mechanisms observed, whether macroscopic mechanisms (adhesion, abrasion, deformation, ...), or microscopic mechanisms (cracking, damage of the WC and Co phases). The numerical simulation using finite elements (FE) proved to be a very interesting complementary tool for the analysis of these wear mechanisms.Our modeling strategy focused on the response of WC-Co at the microstructure scale for the thermomechanical loading close to that obtained by machining. The proposed model takes into account the behavior of the WC and Co phases separately and that of the interfaces WC-WC and WC-Co of the composite. This strategy allowed to study and identify parameters influencing the behavior of the microstructure from the elastic stage to the damage initiation. A good agreement was obtained between the results of the numerical behavior at the initiation of damage in the microstructure and those of the experimental observations in terms of the effects of the cobalt content in the tungsten carbide and of the applied machining conditions
Gianni, Lorenzo. "Electrodialytic recovery of tungsten and cobalt from tungsten carbide scrap". Master's thesis, Alma Mater Studiorum - Università di Bologna, 2022.
Znajdź pełny tekst źródłaDeshpande, Pranav Kishore. "Infrared Processed Copper-Tungsten Carbide Composites". University of Cincinnati / OhioLINK, 2002. http://rave.ohiolink.edu/etdc/view?acc_num=ucin1025107651.
Pełny tekst źródłaKelley, Andrew III. "Tungsten carbide-cobalt by Three Dimensional Printing". Thesis, Massachusetts Institute of Technology, 1998. http://hdl.handle.net/1721.1/32316.
Pełny tekst źródłaIncludes bibliographical references (p. 69-70).
Three Dimensional Printing is an additive manufacturing process for rapid prototyping ceramic and metallic parts [Sachs, et al, 1990]. Green (not sintered) tungsten carbide-cobalt parts must have a density greater than 50% of the theoretical density, 14.9 g/cc, for proper sintering and post-processing. Two approaches were assessed for feasibility and robustness: printing slurry into tungsten carbide-cobalt spray dried powder and printing a solvent in spray dried tungsten carbide powder that readily dissolves. For slurry administered to a powder bed of solid, spherical particles, it has been found that the resulting packing primitive packing fraction increases almost linearly with the volume loading of the slurry over a range of powder size. The increase in density is approximately half what would be calculated by assuming that the slurry fills all the porosity in the powder bed. The maximum green density achieved by printing slurry into a spray dried tungsten carbide-cobalt bed was 41%, midway between the lower bound calculated by assuming the vehicle in the slurry infiltrates only the large pores between the spray dried power and the upper bound calculated by assuming that the vehicle of the slurry also infiltrates the find pores within a spray dried granule. A re-dispersible spray dried powder (38-53 micron size range) was fabricated using only the Duramax 3007 dispersant as the binder. This powder redisperses in water. Administering a drop of water to this powder resulted in primitives with 47% packing density, but which had significant quantities of 80 micron voids.
(cont.) Several lines of evidence pointed to the hypothesis that the voids were the result of trapped air. Two methods were successfully employed to nearly eliminate such voids. In one approach, the droplet of water wvas administered to the powder bed under a vacuum of between 25 and 40 torr and air was admitted to the chamber to 1 atmosphere after different intervals of time ranging from 30 seconds to 10 minutes. In another approach, the ability of water to absorb CO₂ was used to "getter" any trapped gas into the liquid. Water was administered to a powder bed under a CO₂ environment at room temperature. After a 2 minute period, intended to allow the spray dried powder to substantially re-disperse, the temperture of the powder bed was lowered to 0-5 degrees Centigrade in order to increase the amount of CO₂ which could be absorbed in the water and "switch on" the gettering of the trapped gas.Controls were run with the same procedure in air. The primitives made under CO₂ were nearly void free and had densities as high as 52%, while the controls were not significantly different than primitives made at room temperature in air.
by Andrew Kelley, III.
S.M.
Deshpande, Pranav K. "Copper-tungsten carbide composites with infrared processing". Cincinnati, Ohio : University of Cincinnati, 2002. http://rave.ohiolink.edu/etdc/view?acc%5Fnum=ucin1025107651.
Pełny tekst źródłaKsiążki na temat "Tungstene carbide"
Kurlov, Alexey S., i Aleksandr I. Gusev. Tungsten Carbides. Cham: Springer International Publishing, 2013. http://dx.doi.org/10.1007/978-3-319-00524-9.
Pełny tekst źródłaWorld directory and handbookof hardmetals. Wyd. 4. East Barnet: International Carbide Data, 1987.
Znajdź pełny tekst źródłaBrookes, Kenneth J. A. World directory and handbook of hardmetals. Wyd. 4. Barnet, Herts: International Carbide Data, 1987.
Znajdź pełny tekst źródłaLiu, Kui. Tungsten carbide: Processing and applications. Rijeka, Croatia: InTech, 2012.
Znajdź pełny tekst źródłaUpadhyaya, G. S., i Gopal S. Upadhyaya. Cemented tungsten carbides: Production, properties, and testing. Westwood, N.J: Noyes Publications, 1998.
Znajdź pełny tekst źródłaBrookes, Kenneth J. A. World directory and handbook of hardmetals and hard materials. Wyd. 6. East Barnet: International Carbide Data, 1996.
Znajdź pełny tekst źródłaWorld directory and handbook of hardmetals and hard materials. Wyd. 5. East Barnet: International Carbide Data, 1992.
Znajdź pełny tekst źródłaCenter, Langley Research, red. Tensile behavior of tungsten and tungsten-alloy wires from 1300 to 1600 k. Cleveland, Ohio: National Aeronautics and Space Administration, Lewis Research Center, 1988.
Znajdź pełny tekst źródłaH, Titran Robert, i United States. National Aeronautics and Space Administration., red. Tensile and stress-rupture behavior of hafnium carbide dispersed molybdenum and tungsten based alloy wires. [Washington, DC]: National Aeronautics and Space Administration, 1993.
Znajdź pełny tekst źródłaH, Titran Robert, i United States. National Aeronautics and Space Administration., red. Tensile and stress-rupture behavior of hafnium carbide dispersed molybdenum and tungsten based alloy wires. [Washington, DC]: National Aeronautics and Space Administration, 1993.
Znajdź pełny tekst źródłaCzęści książek na temat "Tungstene carbide"
Kurlov, Alexey S., i Aleksandr I. Gusev. "Nanocrystalline Tungsten Carbide". W Tungsten Carbides, 109–89. Cham: Springer International Publishing, 2013. http://dx.doi.org/10.1007/978-3-319-00524-9_4.
Pełny tekst źródłaKurlov, Alexey S., i Aleksandr I. Gusev. "Introduction". W Tungsten Carbides, 1–3. Cham: Springer International Publishing, 2013. http://dx.doi.org/10.1007/978-3-319-00524-9_1.
Pełny tekst źródłaKurlov, Alexey S., i Aleksandr I. Gusev. "Phases and Equilibria in the W–C and W–Co–C Systems". W Tungsten Carbides, 5–56. Cham: Springer International Publishing, 2013. http://dx.doi.org/10.1007/978-3-319-00524-9_2.
Pełny tekst źródłaKurlov, Alexey S., i Aleksandr I. Gusev. "Ordering of Tungsten Carbides". W Tungsten Carbides, 57–108. Cham: Springer International Publishing, 2013. http://dx.doi.org/10.1007/978-3-319-00524-9_3.
Pełny tekst źródłaKurlov, Alexey S., i Aleksandr I. Gusev. "Hardmetals WC–Co Based on Nanocrystalline Powders of Tungsten Carbide WC". W Tungsten Carbides, 191–237. Cham: Springer International Publishing, 2013. http://dx.doi.org/10.1007/978-3-319-00524-9_5.
Pełny tekst źródłaStorms, E. K. "Tungsten Carbides". W Inorganic Reactions and Methods, 314–15. Hoboken, NJ, USA: John Wiley & Sons, Inc., 2007. http://dx.doi.org/10.1002/9780470145265.ch122.
Pełny tekst źródłaShabalin, Igor L. "Tungsten Carbides". W Ultra-High Temperature Materials IV, 11–829. Cham: Springer International Publishing, 2022. http://dx.doi.org/10.1007/978-3-031-07175-1_2.
Pełny tekst źródłaIshizawa, Y., i T. Tanaka. "Fermi surface of hexagonal tungsten carbide". W The Chemistry of Transition Metal Carbides and Nitrides, 121–33. Dordrecht: Springer Netherlands, 1995. http://dx.doi.org/10.1007/978-94-009-1565-7_6.
Pełny tekst źródłaLiu, Kui, Hao Wang i Xinquan Zhang. "Ductile Mode Cutting of Tungsten Carbide". W Springer Series in Advanced Manufacturing, 149–77. Singapore: Springer Singapore, 2019. http://dx.doi.org/10.1007/978-981-32-9836-1_8.
Pełny tekst źródłaFischer, E. O., D. Wittmann, A. Mayr i A. Mcdermott. "Carbyne Complexes of Tungsten". W Inorganic Syntheses, 40–43. Hoboken, NJ, USA: John Wiley & Sons, Inc., 2007. http://dx.doi.org/10.1002/9780470132579.ch9.
Pełny tekst źródłaStreszczenia konferencji na temat "Tungstene carbide"
Wank, A., C. Schmengler, K. Müller-Roden, F. Beck i T. Schläfer. "Aptitude of Different Types of Carbides for Production of Durable Rough Surfaces by Laser Dispersing". W ITSC2017, redaktorzy A. Agarwal, G. Bolelli, A. Concustell, Y. C. Lau, A. McDonald, F. L. Toma, E. Turunen i C. A. Widener. DVS Media GmbH, 2017. http://dx.doi.org/10.31399/asm.cp.itsc2017p0414.
Pełny tekst źródłaPrabin, A., K. S. Anvitha i R. Sathish. "Corrosion Inhibition on Cemented Tungsten Carbides". W Euro Powder Metallurgy 2023 Congress & Exhibition. EPMA, 2023. http://dx.doi.org/10.59499/ep235763660.
Pełny tekst źródłaFiala, P., R. Hepp i A. Zikin. "Alloyed Carbides Beyond WC as a New Material Platform for Solving Challenges in Hardfacing". W ITSC2017, redaktorzy A. Agarwal, G. Bolelli, A. Concustell, Y. C. Lau, A. McDonald, F. L. Toma, E. Turunen i C. A. Widener. DVS Media GmbH, 2017. http://dx.doi.org/10.31399/asm.cp.itsc2017p0408.
Pełny tekst źródłaLyphout, C., J. Kitamura, K. Sato, J. Yamada i S. Dizdar. "Tungsten Carbide Deposition Processes for Hard Chrome Alternative: Preliminary Study of HVAF vs. HVOF Thermal Spray Processes". W ITSC2013, redaktorzy R. S. Lima, A. Agarwal, M. M. Hyland, Y. C. Lau, G. Mauer, A. McDonald i F. L. Toma. ASM International, 2013. http://dx.doi.org/10.31399/asm.cp.itsc2013p0506.
Pełny tekst źródłaLe Bastard, Avigae¨le, Re´mi Batisse i Vincent Gaschignard. "Investigation of a Non-Destructive Method to Characterize Material Mechanical Properties of Pipelines in Service". W 2008 7th International Pipeline Conference. ASMEDC, 2008. http://dx.doi.org/10.1115/ipc2008-64267.
Pełny tekst źródłaVuoristo, P., J. Laurila, T. Mäntylä, K. Niemi, S. Rekola i S. Ahmaniemi. "Surface Changes in Thermally Sprayed Hard Coatings by Wear of Different Abrasives". W ITSC2004, redaktorzy Basil R. Marple i Christian Moreau. ASM International, 2004. http://dx.doi.org/10.31399/asm.cp.itsc2004p1046.
Pełny tekst źródłaScrivani, A., A. Giorgetti, F. Bianchi, L. Campanini, L. Coppelletti i H. Keller. "Thermal Spray Coatings for Application in Petrochemical Field: A Comparison of Tungsten Carbide, Chromium Carbide and Inconel 625". W ITSC 2012, redaktorzy R. S. Lima, A. Agarwal, M. M. Hyland, Y. C. Lau, C. J. Li, A. McDonald i F. L. Toma. ASM International, 2012. http://dx.doi.org/10.31399/asm.cp.itsc2012p0540.
Pełny tekst źródłaGorlenko, Aleksandr, Sergey Davydov i Mikhail Shevtsov. "STRENGTHENING OF CARBIDE STEEL SURFACE BY TUNGSTEN CARBIDE POWDER BY PLASTIC DEFORMATION". W PROBLEMS OF APPLIED MECHANICS. Bryansk State Technical University, 2020. http://dx.doi.org/10.30987/conferencearticle_5fd1ed04a82ac0.47164745.
Pełny tekst źródłaHirata, G. A., O. Contreras, M. H. Farías i L. Cota-Araiza. "Stoichiometric tungsten carbide coatings". W The 8th Latin American congress on surface science: Surfaces , vacuum, and their applications. AIP, 1996. http://dx.doi.org/10.1063/1.51119.
Pełny tekst źródłaSrinivasan, Suresh, Jessica M. Marshall, Joe Gillham i Gurdev Singh. "Tungsten carbide for radiation shielding: A comprehensive review". W Euro Powder Metallurgy 2023 Congress & Exhibition. EPMA, 2023. http://dx.doi.org/10.59499/ep235765427.
Pełny tekst źródłaRaporty organizacyjne na temat "Tungstene carbide"
Dandekar, Dattatraya P. Spall Strength of Tungsten Carbide. Fort Belvoir, VA: Defense Technical Information Center, wrzesień 2004. http://dx.doi.org/10.21236/ada427318.
Pełny tekst źródłaGluth, Jeffrey Weston, Clint Allen Hall, Tracy John Vogler i Dennis Edward Grady. Dynamic compaction of tungsten carbide powder. Office of Scientific and Technical Information (OSTI), kwiecień 2005. http://dx.doi.org/10.2172/922764.
Pełny tekst źródłamazo, isacco, alberto molinari i vincenzo sglavo. Electrical Resistance Flash Sintering of Tungsten Carbide. Peeref, wrzesień 2022. http://dx.doi.org/10.54985/peeref.2209p1889967.
Pełny tekst źródłaReinhart, William Dodd, Tom Finley, III Thornhill, Tracy John Vogler i C. Scott Alexander. Expansion into vacuum of a shocked tungsten carbide-epoxy mixture. Office of Scientific and Technical Information (OSTI), marzec 2009. http://dx.doi.org/10.2172/983671.
Pełny tekst źródłaZ. Zak Fang, H. Y. Sohn. Development of Bulk Nanocrystalline Cemented Tungsten Carbide for Industrial Applicaitons. Office of Scientific and Technical Information (OSTI), marzec 2009. http://dx.doi.org/10.2172/950043.
Pełny tekst źródłaDemaske, Brian. Mesoscale simulations of pressure-shear loading of granular tungsten carbide. Office of Scientific and Technical Information (OSTI), styczeń 2022. http://dx.doi.org/10.2172/2002918.
Pełny tekst źródłaChen, Tianju, Bipul Barua, Tianchen Hu, Mark Messner i Tahany El-Wardany. An ICME Modeling Framework for Titanium/Tungsten-Carbide Metal Matrix Composites. Office of Scientific and Technical Information (OSTI), maj 2023. http://dx.doi.org/10.2172/1985051.
Pełny tekst źródłaKolopus, James A., i Lynn A. Boatner. Single-Crystal Tungsten Carbide in High-Temperature In-Situ Additive Manufacturing Characterization. Office of Scientific and Technical Information (OSTI), maj 2017. http://dx.doi.org/10.2172/1361361.
Pełny tekst źródłaConrad, Hans, i Jay Narayan. Grain Size Hardening and Softening in Tungsten Carbide at Low Homologous Temperatures. Fort Belvoir, VA: Defense Technical Information Center, styczeń 2003. http://dx.doi.org/10.21236/ada422872.
Pełny tekst źródłaDavid Moy, Jun Ma, Robert Hoch, Jim Leacock, Jason Willey, Asif Chishti, Fabio RIbeiro i in. New Nanoscale Catalysts Based on Molybdenum and Tungsten Carbides and Oxycarbides. Office of Scientific and Technical Information (OSTI), sierpień 2002. http://dx.doi.org/10.2172/799250.
Pełny tekst źródła