Gotowa bibliografia na temat „NiCoFeCr system”

The giant magnetoresistance (GMR) effect in FeMn/NiCoFe/Cu/NiCoFe spin valve prepared by dc opposed target magnetron sputtering is reported. The spin valve thin films are characterized by Scanning Electron Microscopy (SEM), Vibrating Sample Magnetometer (VSM) and magnetoresistance ratio measurements. All measurements are performed in room temperature. The inserted 45 mm thickness FeMn layer to the NiCoFe/Cu/NiCoFe system can increase the GMR ratio up to 32.5%. The coercive field to be increased is compared with different FeMn layer thickness. Furthermore, the coercive field (Hc) decreases with increasing FeMn layer thickness. Magnitude of coercive field is 0.1 T, 0.09 T and 0.08 T for FeMn layer thickness is 30 nm, 45 nm and 60 nm, respectively. The FeMn layer is used to lock the magnetization in the ferromagnetic layer through the exchange anisotropy. This paper will describe the development of a GMR spin valve and its magnetic properties.

AbstractHigh-entropy alloys (HEAs) are proposed as potential structural materials for advanced nuclear systems, but little is known about the response of matrix chemistry in HEAs upon irradiation. Here, we reveal a substantial change of matrix chemical concentration as a function of irradiation damage (depth) in equiatomic NiCoFeCr HEA irradiated by 3 MeV Ni ions. After ion irradiation, the matrix contains more Fe/Cr in depth shallower than ~900–1000 nm but more Ni/Co from ~900–1000 nm to the end of the ion-damaged region due to the preferential diffusion of vacancies through Fe/Cr. Preferential diffusion also facilitates migration of vacancies from high radiation damage region to low radiation damage region, leading to no void formation below ~900–1000 nm and void formation around the end of the ion-damaged region at a fluence of 5 × 1016 cm−2 (~123 dpa, displacements per atom, peak dose under full cascade mode). As voids grow significantly at an increased fluence (8 × 1016 cm−2, 196 dpa), the matrix concentration does not change dramatically due to new voids formed below ~900–1000 nm.

Developing efficient seawater-electrolysis system for mass production of hydrogen is highly desirable due to the abundance of seawater. However, continuous electrolysis with seawater feeding boosts the concentration of sodium chloride in the electrolyzer, leading to severe electrode corrosion and chlorine evolution. Herein, the common-ion effect was utilized into the electrolyzer to depress the solubility of NaCl. Specifically, utilization of 6 M NaOH halved the solubility of NaCl in the electrolyte, affording efficient, durable, and sustained seawater electrolysis in NaCl-saturated electrolytes with triple production of H2, O2, and crystalline NaCl. Ternary NiCoFe phosphide was employed as a bifunctional anode and cathode in simulative and Ca/Mg-free seawater-electrolysis systems, which could stably work under 500 mA/cm2 for over 100 h. We attribute the high stability to the increased Na+ concentration, which reduces the concentration of dissolved Cl- in the electrolyte according to the common-ion effect, resulting in crystallization of NaCl, eliminated anode corrosion, and chlorine oxidation during continuous supplementation of Ca/Mg-free seawater to the electrolysis system.

Quantitative diffusion analysis in multicomponent metallic systems has been a formidable task historically and despite decades of research, most of the diffusivity estimations were limited to interdiffusion and some intrinsic diffusion coefficients in binary systems and interdiffusion coefficients in a few ternary systems until recently. The experimental complications associated with the need to intersect (n-1) serpentine diffusion paths in the n dimensional space for determining the 〖(n-1)〗^2 interdiffusion coefficients lead to various approaches like average diffusivity, square root diffusivity estimations that approximate a representative value of the diffusivity across a composition range from a single experiment. However, these values are not material constants and do not provide any information about the atomic interactions. This lack of diffusivity data in multicomponent systems has hampered the development of mobility databases essential for various simulations and physico-chemical studies of materials. This work resolves the issues with quantitative multicomponent diffusion analysis via several newly proposed methods that solves the issue of intersecting diffusion paths through the application of special constrained diffusion paths. The equations necessary to apply these methods are derived and their application is discussed mathematically and applied experimentally to the model alloy system, the NiCoFeCr equiatomic multiprincipal element alloy to compare with available radiotracer data measured for this system. The work first employs the pseudo-binary diffusion couple approach that develops a rectilinear diffusion path in the multicomponent space to the NiCoFeCr system to estimate the tracer coefficients from the intrinsic coefficients at the marker plane. The mathematical formulations derived for the same justify its namesake and the obtained tracer coefficients can be used to back calculate the intrinsic and interdiffusion coefficients. The pseudo-ternary method improves on the shortcomings of the pseudo-binary diffusion couple method and enables the estimation of tracer coefficients of three components by crossing two constrained diffusion paths in a 2d plane in addition to the main and cross interdiffusion coefficients. The body diagonal method originally proposed for determination of interdiffusion coefficients is modified here to determine the tracer coefficients of all components using only two diffusion profiles thus reducing the errors associated with crossing (n-1).paths per the original approach. This work then explores the possibilities of crossing dissimilar constrained diffusion paths by crossing pseudo ternaries of different types. Strategically crossing a rectilinear pseudo-binary diffusion path with a serpentine conventional (body diagonal) diffusion path overcomes all the previous drawbacks of pseudo binary, pseudo ternary and body diagonal methods to determine the full set of diffusivities at any desired composition and generalizes the constrained diffusion path approach to any order multicomponent system. The obtained tracer coefficients show a good match with the diffusivities measured in radio tracer experiments. Finally, based on the ideas from the constrained diffusion path experiments in the NiCoFeCr system, a constrained path approach is devised to measure the diffusivities in an Al based NiCoFeCr multiprincipal element alloy system which was not possible earlier due to unavailability of radio isotopes and the complexities of interdiffusion experiments in higher order systems. The obtained tracer diffusivities, show an excellent match with the trends extrapolated from lower order systems. Calculated intrinsic and interdiffusion coefficients demonstrate the importance of vacancy wind effect as well as the issues with using diffusivities having different dependent components to make predictions on diffusion trends among different elements.