Gotowe bibliografie tematyczne / Ni-Ni3B

Spis treści

Artykuły w czasopismach
Streszczenia konferencji

Gotowa bibliografia na temat „Ni-Ni3B”

Autor: Grafiati

Data publikacji: 6 września 2023

Utwórz poprawne odniesienie w stylach APA, MLA, Chicago, Harvard i wielu innych

Wybierz rodzaj źródła:

Zobacz listy aktualnych artykułów, książek, rozpraw, streszczeń i innych źródeł naukowych na temat „Ni-Ni3B”.

Przycisk „Dodaj do bibliografii” jest dostępny obok każdej pracy w bibliografii. Użyj go – a my automatycznie utworzymy odniesienie bibliograficzne do wybranej pracy w stylu cytowania, którego potrzebujesz: APA, MLA, Harvard, Chicago, Vancouver itp.

Możesz również pobrać pełny tekst publikacji naukowej w formacie „.pdf” i przeczytać adnotację do pracy online, jeśli odpowiednie parametry są dostępne w metadanych.

Artykuły w czasopismach na temat "Ni-Ni3B"

Azhazha, V. M., V. E. Semenenko i N. N. Pilipenko. "Ni-Ni3B composite coating". Powder Metallurgy and Metal Ceramics 46, nr 1-2 (styczeń 2007): 32–37. http://dx.doi.org/10.1007/s11106-007-0006-8.

Pełny tekst źródła

Style APA, Harvard, Vancouver, ISO itp.

Xu, Jun Feng, Feng Liu, Man Zhu i Zeng Yun Jian. "Differential Scanning Calorimetry Studies on Ni-Ni₃B Alloys". Materials Science Forum 817 (kwiecień 2015): 556–59. http://dx.doi.org/10.4028/www.scientific.net/msf.817.556.

Pełny tekst źródła

Streszczenie:

Solidification behaviors of hypoeutectic Ni-3.3wt% B and hypereutectic Ni-4.5wt% B alloys were investigated by using differential scanning calorimetry (DSC) technology. Experimental results showed that the solidification behaviors are similar for the two kinds of alloys with small sizes, i.e. three transformed peaks (corresponding to L→α-Ni, L→Ni-Ni23B6and Ni23B6→Ni+Ni3B, respectively) appear in the cooling curves, and three phases (primary phase α-Ni, rod eutectic and dot precipitates) appear in the microstructures, which are different from that of the alloys with large sizes. It can be attributed to the fact that the nucleation of α-Ni and Ni23B6phases are easier than that of Ni3B phase for small samples of hypoeutectic and hypereutectic Ni-Ni3B alloys.

Style APA, Harvard, Vancouver, ISO itp.

Kim, Yong Hwan, Il Ho Kim, K. T. Kim, Seung Y. Shin i S. I. Kwun. "Identification of Phases in the Wide-Gap Region Brazed with BNi-3 Filler Metal Powder Using Electron Backscatter Diffraction". Materials Science Forum 544-545 (maj 2007): 355–58. http://dx.doi.org/10.4028/www.scientific.net/msf.544-545.355.

Pełny tekst źródła

Streszczenie:

The phases formed in the wide-gap region brazed with BNi-3 filler metal powder in IN738 superalloy were investigated by electron backscatter diffraction (EBSD). The morphology and chemical composition of the phase were investigated by field emission scanning electron microscopy (FESEM) and Auger electron spectroscopy (AES). The wide-gap region brazed with BNi-3 filler metal had a microstructure consisting of primary Ni3B, binary eutectic of Ni3B-Ni solid solution and ternary eutectic of Ni3B-Ni-Ni3Si structure. EBSD pattern analysis revealed that the Ni3B had orthorhombic structure with lattice parameter of a=0.439, b=0.522 and c=0.662 nm, and the Ni3Si phase had cubic structure with lattice parameter of a=0.350 nm.

Style APA, Harvard, Vancouver, ISO itp.

Kim, Yong Hwan, i S. I. Kwun. "Changes in Mechanical Properties of the Wide-Gap Region Brazed with Various Brazing Temperatures and Times". Materials Science Forum 486-487 (czerwiec 2005): 113–16. http://dx.doi.org/10.4028/www.scientific.net/msf.486-487.113.

Pełny tekst źródła

Streszczenie:

The microstructural changes and the relations between mechanical properties and additive powder with various brazing temperatures and times were investigated. The IN738 and BNi-3 alloy powders were used as an additive and filler metal powders for the brazing process. The wide-gap brazing process was carried out in a vacuum of 2×10-5 torr. The wide-gap region brazed with 60wt.% IN738 additive powder had a microstructure consisting of IN738 additive, and binary eutectic of Ni3B-Ni, and (Cr, W)B. As the brazing temperature and time were increased, the size of IN738 additive powder increased to 181µm, which decreased the amount of low strength Ni3B-Ni eutectic structure, thereby increasing the fracture strength of the wide-gap brazed region. Cracks in the brazed region were observed to propagate through the Ni3B-Ni structure, which lowered the fracture strength of the wide-gap brazed region.

Style APA, Harvard, Vancouver, ISO itp.

Kim, Yong Hwan, Ki Tae Kim i Il Ho Kim. "Effect of Mixing Ratio on Mechanical Properties of Wide-Gap Brazed Ni-Based Superalloy with Ni-Si-B Alloy Powder". Key Engineering Materials 306-308 (marzec 2006): 935–40. http://dx.doi.org/10.4028/www.scientific.net/kem.306-308.935.

Pełny tekst źródła

Streszczenie:

This study investigated the microstructure and mechanical properties of a wide-gap region brazed with various powders mixing ratios of additive powder to filler metal powder. The IN738 and BNi-3 alloy powders were used as additive and filler metal powder for the brazing process. The wide-gap brazing process was carried out in a vacuum of 2×10-5 torr. It was observed that the region brazed with only filler metal had a microstructure consisting of fully eutectic and dendrite structures. However, the region brazed with 60wt.% IN738 additive powder consisted of IN738 additive, Ni3B-Ni eutectic and (Cr, W)B. The fracture strength of the wide-gap region (70 wt.% additive and 30 wt.% filler metal powder) was as high as 687 MPa at room temperature. The Cracks in the wide-gap brazed region initiated at the Ni3B-Ni eutectic and (Cr, W)B, and then propagated through them. It was found that the Ni3B-Ni eutectic and (Cr, W)B in the brazed region are important microstructural factors affecting the mechanical properties of the wide-gap brazed region.

Style APA, Harvard, Vancouver, ISO itp.

Pal, Soupitak, Vikram Jayaram, Sanjay Kumar Biswas i Yancy Riddle. "Effect of Phases on the Frictional Properties of Electroless Ni-B Nano-Composite Coating". Advances in Science and Technology 66 (październik 2010): 120–25. http://dx.doi.org/10.4028/www.scientific.net/ast.66.120.

Pełny tekst źródła

Streszczenie:

As-deposited amorphous (determined through XRD) electroless Ni-B coating upon heat treatment transforms to crystalline phases, Ni3B, Ni2B and Ni whose volume fractions can vary widely. A micro and nano tribological study through ball-on-disk tribometer and lateral force microscopy has been performed to understand the effect of phase mixture (Ni3B +Ni2B) on the frictional properties of this coating. Though scaling of the contact area from micro to nano level strongly influences the friction coefficient, it has also been found that increase in the Ni2B:Ni3B ratio of the crystalline coating reduces the friction coefficient significantly.

Style APA, Harvard, Vancouver, ISO itp.

Kornienko, Elena, Aelita Nikulina, Ekaterina Drobyaz, Natalya V. Plotnikova, Elizaveta Lapushkina i Victor Kuz'min. "The Effect of Heat Temperature on the Structure of Plasma Coating of the Ni-Cr-Si-B System". Applied Mechanics and Materials 788 (sierpień 2015): 252–58. http://dx.doi.org/10.4028/www.scientific.net/amm.788.252.

Pełny tekst źródła

Streszczenie:

The powder of the Ni-Cr-Si-B system was applied on tubes of low carbon steel (0.2 % C) with the help of air-plasma spraying. The effect of heating temperature on the microstructure of obtained coatings was analyzed in this paper. The coatings were heated up to 500, 600, 700, 800, 900, 1000, and 1100 °C and cooled in the air. It was shown by the method of optical and scanning electron microscopy (SEM) and the X-ray diffraction analysis (XRD) that the same phases (γ-Ni, Ni3B, Ni3Si and Cr2B) were present in the coatings before and after heating. Chromium carbide Cr7C3 was observed in the coating structure after heating to above 1000 °C. Coatings which were heated to 1000 °C consisted of grains of the solid nickel base solution, micro volumes of the Ni+Ni3Si eutectic with inclusions of Ni3B and particles of Cr7C3. The coatings which were crystallized from a liquid state (heated up to 1100 °C) consisted of large areas of the solid nickel base solution and particles of chromium carbide Cr7C3. The space between nickel areas is filled by the Ni3Si+Ni3B eutectic.

Style APA, Harvard, Vancouver, ISO itp.

Shahbazi, Mahboobeh, Henrietta Cathey, Natalia Danilova i Ian Mackinnon. "Single Step Process for Crystalline Ni-B Compounds". Materials 11, nr 7 (22.07.2018): 1259. http://dx.doi.org/10.3390/ma11071259.

Pełny tekst źródła

Streszczenie:

Crystalline Ni2B, Ni3B, and Ni4B3 are synthesized by a single-step method using autogenous pressure from the reaction of NaBH4 and Ni precursors. The effect of reaction temperature, pressure, time, and starting materials on the composition of synthesized products, particle morphologies, and magnetic properties is demonstrated. High yields of Ni2B (>98%) are achieved at 2.3–3.4 MPa and ~670 °C over five hours. Crystalline Ni3B or Ni4B3 form in conjunction with Ni2B at higher temperature or higher autogenous pressure in proportions influenced by the ratios of initial reactants. For the same starting ratios of reactants, a longer reaction time or higher pressure shifts equilibria to lower yields of Ni2B. Using this approach, yields of ~88% Ni4B3 (single phase orthorhombic) and ~72% Ni3B are obtained for conditions 1.9 MPa < Pmax < 4.9 MPa and 670 °C < Tmax < 725 °C. Gas-solid reaction is the dominant transformation mechanism that results in formation of Ni2B at lower temperatures than conventional solid-state methods.

Style APA, Harvard, Vancouver, ISO itp.

Kim, Yong Hwan, i S. I. Kwun. "Phase Analysis in the Region Brazed with Ni-14Cr-10Co-3.5Al-2.5Ta-2.8B Filler Metal Using Electron Backscatter Diffraction". Materials Science Forum 569 (styczeń 2008): 93–96. http://dx.doi.org/10.4028/www.scientific.net/msf.569.93.

Pełny tekst źródła

Streszczenie:

The phases formed in the wide-gap region brazed with Ni-14Cr-10Co-3.5Al-2.5Ta-2.8B filler metal powder in IN738 superalloy were investigated by electron backscatter diffraction (EBSD). The wide-gap brazing process was carried out in a vacuum of 2×10-5 torr at 1503 K. The region brazed with filler metal powders had a microstructure consisting of two kinds of eutectic colonies, one is Ni solid solution-CrB eutectic and the other is Ni solid solution-Ni3B eutectic. EBSD pattern analysis revealed that the CrB phase had orthorhombic structure with lattice parameters of a=0.297, b=0.786 and c=0.293 nm, and the Ni3B phase had orthorhombic structure with lattice parameters of a=0.439, b=0.522 and c=0.662 nm. The cuboidal-shaped phase precipitated in the Ni solid solution was found to be the γ' (Ni3Al) phase, which had cubic structure with lattice parameter of a=0.357 nm.

Style APA, Harvard, Vancouver, ISO itp.

Liu, Feng, Junfeng Xu, Di Zhang i Zengyun Jian. "Solidification of Highly Undercooled Hypereutectic Ni-Ni3B Alloy Melt". Metallurgical and Materials Transactions A 45, nr 11 (22.07.2014): 4810–19. http://dx.doi.org/10.1007/s11661-014-2460-5.

Pełny tekst źródła

Style APA, Harvard, Vancouver, ISO itp.

Więcej źródeł

Streszczenia konferencji na temat "Ni-Ni3B"

Wu, C. Q., K. S. Zhou, C. G. Deng i C. M. Deng. "HVAF Sprayed Composite Coating with Ni-base Self-Fluxing Alloy and WC on a Copper Substrate". W ITSC2006, redaktorzy B. R. Marple, M. M. Hyland, Y. C. Lau, R. S. Lima i J. Voyer. ASM International, 2006. http://dx.doi.org/10.31399/asm.cp.itsc2006p0689.

Pełny tekst źródła

Streszczenie:

Abstract In order to improve the wear resistance and service life of the copper, the composite coating consisting of a Ni-base self-fluxing alloy (NiCrWB+50%Al2O3) and WC (WC-12%Co) alloy were sprayed on a copper substrate using High Velocity Air Fuel(HVAF). The coating could meet the operating requirements including high hardness, good wear resistance and low cost. The Ni-base composite coating was analyzed by means of optical microscopy, scanning electron microscopy (SEM), electron probe microanalysis (EPMA) and X-ray diffraction (XRD). The results indicated that the structure of coating was composed of melted particles and partly unmelted round particles of Ni-base alloy, and WC particle. Only a small proportion of the Al2O3 particles were retained in the coating. The phases in the coating consisted of γ-Ni, WC and a little Ni3B. Amorphous structures appeared and some Al2O3 phase existed. The adhesion strength between coating and copper substrate was more than 50MPa. Wear results showed that the Ni-base composite coating exhibited better wear resistance than the coating with no WC particles.

Style APA, Harvard, Vancouver, ISO itp.

Oferujemy zniżki na wszystkie plany premium dla autorów, których prace zostały uwzględnione w tematycznych zestawieniach literatury. Skontaktuj się z nami, aby uzyskać unikalny kod promocyjny!