Gotowa bibliografia na temat „MODE SHAPE SLOPE”

Soil-rock slopes are widely distributed around the world, while the commonly adopted method by simplifying it as a uniform media tends to be excessively conservative. In this study, a slope stability analysis method considering the nonuniform characteristics of rocks was proposed. It was found that the distribution, relative position, and shape of rock have significant effect on slope stability. For the influence of distribution, large rocks at the foot of slope have the most significant effect on slope stability while the effect is insignificant when the rocks are on the slope surface. In terms of the relative position of rocks, four plastic expansion modes of bypass, diversion, inclusion, and penetration were put forward through the analysis on the expansion mode of the plastic zone. Moreover, rock shape also has influence on slope stability.

For the small crack detection (crack ration less than 5%), the derivatives of mode shapes of cantilever beams were used for crack detection in the beams. These derivatives consist of the slope, curvature and rate of curvature, which are the first, second and third derivatives of the displacement mode shape respectively. The presence of a crack results in a slight change in the mode shape of a structure which is manifested as a small discontinuity in the response at the crack location. It is hard to detect small cracks in beams using the direct data of mode shape change. But when the first, second and third derivatives of the displacement mode shape, that is the slope, curvature and rate of curvature, respectively, of the cracked cantilever beam provide a progressively better indication of the presence of a crack. However, `noise' effects due to the difference approximation error also begin to be magnified at higher derivatives so that it is not advantageous to go beyond the third derivatives of mode shapes. For the intact beam, these derivatives are smooth curves. So the local peaks or discontinuity on the slope, curvature and rate of curvature modal curves can be used to indicate abnormal mode shape changes at those positions. In this way, these local peak positions can be used to detect and locate cracks in the structure. The modal responses of the damaged and intact cantilever beams used were computed using the finite element method.

The objective of this study was to provide an overarching description of the inter-subject variability of the equine femur and tibia morphology using statistical shape modeling. Fifteen femora and fourteen tibiae were used for building the femur and tibia statistical shape models, respectively. Geometric variations in each mode were explained by biometrics measured on ±3 standard deviation instances generated by the shape models. Approximately 95% of shape variations within the population were described by 6 and 3 modes in the femur and tibia shape models, respectively. In the femur shape model, the first mode of variation was scaling, followed by notable variation in the femoral mechanical-anatomical angle and femoral neck angle in mode 2. Orientation of the femoral trochlear tubercle and femoral version angle were described in mode 3 and mode 4, respectively. In the tibia shape model, the main mode of variation was also scaling. In mode 2 and mode 3, the angles of the coronal tibial plateau and the medial and lateral caudal tibial slope were described, showing the lateral caudal tibial slope angle being significantly larger than the medial. The presented femur and tibia shape models with quantified biometrics, such as femoral version angle and posterior tibial slope, could serve as a baseline for future investigations on correlation between the equine stifle morphology and joint disorders due to altered biomechanics, as well as facilitate the development of novel surgical treatment and implant design. By generating instances matching patient-specific femorotibial joint anatomy with radiographs, the shape model could assist virtual surgical planning and provide clinicians with opportunities to practice on 3D printed models.

Filtered mode shapes are used to detect the presence, location, size and shape of the delaminations in composite laminated plates with various boundary conditions. This method is the extension of a previous study by the authors on the delamination detection in the beams using irregularities of the mode shapes. The mode shapes are filtered to separate the smooth and irregular parts. Presence and situation of delamination affects these separated parts, and these effects are used to detect the delamination. Here, two new indicators, named ‘slope of smooth part’ and ‘irregularities in the slope of smooth part’, are introduced to increase the clarity of detected damage and reduce the noisy effects. The former one is obtained by differentiating the smooth part of the mode shape and the latter by applying the filter on the slope of smooth part for another time. Using this method and the mentioned indicators, delaminations may be detected in the plates using the data of just the damaged structure. This is considered as an important advantage of the method as we do not need the intact structure data. The method is validated utilizing the numerical data for a delaminated plate model. This method lacks the ability to locate the position of delamination through the thickness and the delamination should not be too close to the edges of the plate.

The finite element method (FEM) and the limit equilibrium method (LEM) are commonly used for calculating slope failure risk. However, the FEM needs to carry out post-processing to estimate slope sliding surface, while the LEM requires assumption of the shape and location of the sliding surface in advance. In this paper, an element failure risk method (EFR) for calculating soil slope failure risk is proposed based on element failure probability (EFP) acquired by plastic limit analysis. The proposed method does not require any assumptions about failure modes. Firstly, the non-common-node triangle element is used to discrete the slope then the random field is generated based on the Cholesky decomposition midpoint method. According to the reliability stochastic programming model and solution strategy, the external overload coefficient, bulk overload coefficient, slope stability coefficient and velocity field of the slope under each random field are obtained, according to which the failure of the element is judged and the failure risk of the slope is calculated. In order to verify the correctness of the proposed method, two classical slopes are systematically analyzed. The research shows that compared with the traditional slope failure risk analysis method, the greatest advantage of the proposed method is that it can capture all failure modes of the slope and greatly simplify the calculation of the slope failure consequences of each failure mode. An efficient upper bound method (UBM) parallel program is prepared, which greatly improves the calculation efficiency.

The Euler–Bernoulli theory of beams is usually presented in two forms: (i) in the linear case of a small slope using Cartesian coordinates along and normal to the straight undeflected position; and (ii) in the non-linear case of a large slope using curvilinear coordinates along the deflected position, namely, the arc length and angle of inclination. The present paper starts with the exact equation in a third form, that is, (iii) using Cartesian coordinates along and normal to the undeflected position like (i), but allowing exactly the non-linear effects of a large slope like (ii). This third form of the equation of the elastica shows that the exact non-linear shape is a superposition of linear harmonics; thus, the non-linear effects of a large slope are equivalent to the generation of harmonics of a linear solution for a small slope. In conclusion, it is shown that: (i) the critical buckling load is the same in the linear and non-linear cases because it is determined by the fundamental mode; (ii) the buckled shape of the elastica is different in the linear and non-linear cases because non-linearity adds harmonics to the fundamental mode. The non-linear shape of the elastica, for cases when powers of the slope cannot be neglected, is illustrated for the first four buckling modes of cantilever, pinned, and clamped beams with different lengths and amplitudes.

We implement the concept of the distributed electrode, which allows to improve the modal behavior of lasers and to reduce spatial-hole burning effects by preferentially localizing current injection in the center of the structure, hence discriminating the optical mode. We report the first realization of distributed electrode lasers emitting at 808 nm with the measured full width at half maximum (FWHM) angle of the minimal horizontal angle as 3.8° while the maximum continuous-wave output power is up to 4 W and high slope efficiencies as high as 0.95 W/A.

AbstractMesoscale eddies shape the Beaufort Gyre response to Ekman pumping, but their transient dynamics are poorly understood. Climate models commonly use the Gent–McWilliams (GM) parameterization, taking the eddy streamfunction to be proportional to an isopycnal slope s and an eddy diffusivity K. This local-in-time parameterization leads to exponential equilibration of currents. Here, an idealized, eddy-resolving Beaufort Gyre model is used to demonstrate that carries a finite memory of past ocean states, violating a key GM assumption. As a consequence, an equilibrating gyre follows a spiral sink trajectory implying the existence of a damped mode of variability—the eddy memory (EM) mode. The EM mode manifests during the spinup as a 15% overshoot in isopycnal slope (2000 km3 freshwater content overshoot) and cannot be explained by the GM parameterization. An improved parameterization is developed, such that is proportional to an effective isopycnal slope , carrying a finite memory γ of past slopes. Introducing eddy memory explains the model results and brings to light an oscillation with a period ≈ 50 yr, where the eddy diffusion time scale TE ~ 10 yr and γ ≈ 6 yr are diagnosed from the eddy-resolving model. The EM mode increases the Ekman-driven gyre variance by γ/TE ≈ 50% ± 15%, a fraction that stays relatively constant despite both time scales decreasing with increased mean forcing. This study suggests that the EM mode is a general property of rotating turbulent flows and highlights the need for better observational constraints on transient eddy field characteristics.

The stability assessment of sedimentary rock slopes of the area surround Garin Majjed archeological village which lay on cuesta shape hill in Wadi Dawa'an - East of Yemen was carried out. All important factors affecting slope stability in the area such as differential weathering, rainfall and runoff, sewage, discontinuities trends and inclinations, slope face orientation, and mechanical properties of rocks and joints filling materials were evaluated. Direct shear test of joints filling materials showed that the friction angle (Φ) values range between 11˚ and 31˚ and cohesion (C) Values between 0.00 and 0.5 MPa. The compressive strength (cσ) values of the nodular limestone rocks is 66 MPa and for shaley marly sandstone it is 12 MPa. It was found that rock fall is the main mode of failure in the area, while secondary toppling and/ or plane sliding are probable to occur. Some remedial measures are proposed to protect the slopes like erect well seal drainage path, supporting the toe of the dip slope and the overhanging parts, as well as grouting of joints by convenient filling material.

Structural Health Monitoring is a field focusing to enhance structural serviceability by periodic safety evaluation of the structural strength and stability. If the damages in the structure can be detected early, the structure can be saved from collapsing by using the proper retrofitting techniques. In this thesis, mode shape slope and curvature method has been used to detect damage and understand which mode’s derivative are capable of detect damage in the building at different story. Three different height of building has been considered to understand the efficiency of the damage detection technique for the first five mode shape derivative of the building. First, damage is introduced in the building by reducing the stiffness of that story where damage is need to be detect by using the mode shape slope and curvature method. Modal analysis is done, to obtain the natural frequency and mode shape of the undamaged and damaged building. With the help of the central difference method, the derivatives of the mode shape have been calculated for the both buildings. Forward difference method is used at the fixed end of the building while backward difference method is used at the free end of the building. After obtaining the derivatives (i.e. 1st derivative and 2nd derivative), difference between undamaged and damaged mode shape slope/curvature is calculated and then normalized them to unity. Normalized mode shape slope and curvature is plotted to detect the damaged location in the building, A MATLAB programme has been written for the analysis of the undamaged and damaged building. It has been observed from the result show mode shape based methods are capable of detecting the damages. The difference between undamaged and damaged mode shape slope shows a higher value between damaged story and story before it. A sudden rise in function values such function known as Dirac-delta function in mathematical terms. The difference between iv undamaged and damaged mode shape curvature changes it sign at the damaged location and reaches very large positive value at damaged location. Results shows mode shape curvature is capable of detect damage easily as compared to mode shape slop. It has been observed from the results that few higher mode of the building start contributing in damage detection as the height of the building increases. Low level damage can be also detected from the mode shape slope and curvature method.

碩士
國立高雄科技大學
環境與安全衛生工程系
107
With the demand for economic activities and the development of engineering technology, the vehicle tunnels in the metropolitan area gradually appear irregular shapes to bypass natural or man-made obstacles. U-shaped tunnels are common tunnel types. The characteristics of these tunnels are that the length is not necessarily long, but the slope of the entrance is steep because the entrance to the driveway reaches a certain depth in the extremely short hinterland. This type of tunnel includes cross-river tunnels, cross-lake tunnels, cross-harbour tunnels and special tunnels in urban areas. Due to the large number of vehicles and passers-by, evacuation and disaster relief activities will face extremely severe conditions when fires occur in this type of tunnels. Current research rarely discusses the relationship between U-shaped tunnel entrance slope and fire hazard. This study has analyzed the effects of different entrance slopes on both sides of the tunnel and the push-pull phenomenon due to the stack effect. The research method is to use the numerical simulation and model experiments to verify. The conditions of the U-shaped tunnel in the event of a fire are analyzed by FDS. Schlieren photography technique is used to record the variation of the heat flow in the glass tunnel models when various slopes are at the ends of the structure. The stack effect are clearly demonstrated to affect the hot flow and smoke in the model tunnels. The hazards of fires in U-shaped tunnels and the effects of personnel evacuation have been discussed in this study through numerical simulations and model experiments. The results are very helpful in enhancing the fire safety of U-shaped tunnels. Keywords: U-shaped tunnel, vehicle tunnel fire, stack effect, push-pull effect, Fire Dynamics Simulator (FDS), Schlieren photography technique

Apparel Design Through Patternmaking is a fresh design-oriented flat patternmaking text that gives fashion students a new perspective on patternmaking knowledge and skills they need to develop contemporary women’s, men’s, and children’s wear. This book covers a comprehensive range of concepts in flat pattern drafting, such as fit, style, and design development, and the modular approach allows for flexible design options across age, gender, and size, as reflected in current fashion trends. 200 detailed principles address proper measurements; body shapes; dart manipulation; neckline, collar, and sleeve variations; fit issues and corrections; garment details; and more, all of which are easily visualized with hundreds of line drawings and photos. Reference size charts and a decimal conversion chart included in the Appendix make this text user-friendly for international students. Key Features: - 20 slopers, 30 foundations, and variations - 220 detailed principles of patternmaking - 100+ applied garment designs - A chapter on Cut & Sew stretch fabrics - Learning objectives with clear flat sketches in each chapter - A decimal conversion chart, reference size charts, and glossary of key terms STUDIO Features Include: - Watch videos that show the development process for customized sloper sets - Review concepts with flashcards of essential vocabulary - Practice with additional 1/2 scale slopers Instructor Resources Include: - Instructor’s Guide provides suggestions for planning the course and using the text in the classroom, supplemental assignments, and lecture notes

The aim of the paper was to determine the influence of root systems of chosen tree species found in the Polish Flysch Carpathians on the increase of soil shear strength (root cohesion) in terms of slope stability. The paper's goal was achieved through comprehensive tests on root systems of eight relatively common in the Polish Flysch Carpathians tree species. The tests that were carried out included field work, laboratory work and analytical calculations. As part of the field work, the root area ratio (A IA) of the roots was determined using the method of profiling the walls of the trench at a distance of about 1.0 m from the tree trunk. The width of the. trenches was about 1.0 m, and their depth depended on the ground conditions and ranged from 0.6 to 1.0 m below the ground level. After preparing the walls of the trench, the profile was divided into vertical layers with a height of 0.1 m, within which root diameters were measured. Roots with diameters from 1 to 10 mm were taken into consideration in root area ratio calculations in accordance with the generally accepted methodology for this type of tests. These measurements were made in Biegnik (silver fir), Ropica Polska (silver birch, black locust) and Szymbark (silver birch, European beech, European hornbeam, silver fir, sycamore maple, Scots pine, European spruce) located near Gorlice (The Low Beskids) in areas with unplanned forest management. In case of each tested tree species the samples of roots were taken, transported to the laboratory and then saturated with water for at least one day. Before testing the samples were obtained from the water and stretched in a. tensile testing machine in order to determine their tensile strength and flexibility. In general, over 2200 root samples were tested. The results of tests on root area ratio of root systems and their tensile strength were used to determine the value of increase in shear strength of the soils, called root cohesion. To this purpose a classic Wu-Waldron calculation model was used as well as two types of bundle models, the so called static model (Fiber Bundle Model — FIRM, FBM2, FBM3) and the deformation model (Root Bundle Model— RBM1, RBM2, mRBM1) that differ in terms of the assumptions concerning the way the tensile force is distributed to the roots as well as the range of parameters taken into account during calculations. The stability analysis of 8 landslides in forest areas of Cicikowicleie and Wignickie Foothills was a form of verification of relevance of the obtained calculation results. The results of tests on root area ratio in the profile showed that, as expected, the number of roots in the soil profile and their ApIA values are very variable. It was shown that the values of the root area ratio of the tested tree species with a diameter 1-10 ram are a maximum of 0.8% close to the surface of the ground and they decrease along with the depth reaching the values at least one order of magnitude lower than close to the surface at the depth 0.5-1.0 m below the ground level. Average values of the root area ratio within the soil profile were from 0.05 to 0.13% adequately for Scots pine and European beech. The measured values of the root area ratio are relatively low in relation to the values of this parameter given in literature, which is probably connected with great cohesiveness of the soils and the fact that there were a lot of rock fragments in the soil, where the tests were carried out. Calculation results of the Gale-Grigal function indicate that a distribution of roots in the soil profile is similar for the tested species, apart from the silver fir from Bie§nik and European hornbeam. Considering the number of roots, their distribution in the soil profile and the root area ratio it appears that — considering slope stability — the root systems of European beech and black locust are the most optimal, which coincides with tests results given in literature. The results of tensile strength tests showed that the roots of the tested tree species have different tensile strength. The roots of European beech and European hornbeam had high tensile strength, whereas the roots of conifers and silver birch in deciduous trees — low. The analysis of test results also showed that the roots of the studied tree species are characterized by high variability of mechanical properties. The values Of shear strength increase are mainly related to the number and size (diameter) of the roots in the soil profile as well as their tensile strength and pullout resistance, although they can also result from the used calculation method (calculation model). The tests showed that the distribution of roots in the soil and their tensile strength are characterized by large variability, which allows the conclusion that using typical geotechnical calculations, which take into consideration the role of root systems is exposed to a high risk of overestimating their influence on the soil reinforcement. hence, while determining or assuming the increase in shear strength of soil reinforced with roots (root cohesion) for design calculations, a conservative (careful) approach that includes the most unfavourable values of this parameter should be used. Tests showed that the values of shear strength increase of the soil reinforced with roots calculated using Wu-Waldron model in extreme cases are three times higher than the values calculated using bundle models. In general, the most conservative calculation results of the shear strength increase were obtained using deformation bundle models: RBM2 (RBMw) or mRBM1. RBM2 model considers the variability of strength characteristics of soils described by Weibull survival function and in most cases gives the lowest values of the shear strength increase, which usually constitute 50% of the values of shear strength increase determined using classic Wu-Waldron model. Whereas the second model (mRBM1.) considers averaged values of roots strength parameters as well as the possibility that two main mechanism of destruction of a root bundle - rupture and pulling out - can occur at the same. time. The values of shear strength increase calculated using this model were the lowest in case of beech and hornbeam roots, which had high tensile strength. It indicates that in the surface part of the profile (down to 0.2 m below the ground level), primarily in case of deciduous trees, the main mechanism of failure of the root bundle will be pulling out. However, this model requires the knowledge of a much greater number of geometrical parameters of roots and geotechnical parameters of soil, and additionally it is very sensitive to input data. Therefore, it seems practical to use the RBM2 model to assess the influence of roots on the soil shear strength increase, and in order to obtain safe results of calculations in the surface part of the profile, the Weibull shape coefficient equal to 1.0 can be assumed. On the other hand, the Wu-Waldron model can be used for the initial assessment of the shear strength increase of soil reinforced with roots in the situation, where the deformation properties of the root system and its interaction with the soil are not considered, although the values of the shear strength increase calculated using this model should be corrected and reduced by half. Test results indicate that in terms of slope stability the root systems of beech and hornbeam have the most favourable properties - their maximum effect of soil reinforcement in the profile to the depth of 0.5 m does not usually exceed 30 kPa, and to the depth of 1 m - 20 kPa. The root systems of conifers have the least impact on the slope reinforcement, usually increasing the soil shear strength by less than 5 kPa. These values coincide to a large extent with the range of shear strength increase obtained from the direct shear test as well as results of stability analysis given in literature and carried out as part of this work. The analysis of the literature indicates that the methods of measuring tree's root systems as well as their interpretation are very different, which often limits the possibilities of comparing test results. This indicates the need to systematize this type of tests and for this purpose a root distribution model (RDM) can be used, which can be integrated with any deformation bundle model (RBM). A combination of these two calculation models allows the range of soil reinforcement around trees to be determined and this information might be used in practice, while planning bioengineering procedures in areas exposed to surface mass movements. The functionality of this solution can be increased by considering the dynamics of plant develop¬ment in the calculations. This, however, requires conducting this type of research in order to obtain more data.

Nationalism: Past as Prologue began as a single volume being compiled by Ad Akande, a scholar from South Africa, who proposed it to me as co-author about two years ago. The original idea was to examine how the damaging roots of nationalism have been corroding political systems around the world, and creating dangerous obstacles for necessary international cooperation. Since I (Bruce E. Johansen) has written profusely about climate change (global warming, a.k.a. infrared forcing), I suggested a concerted effort in that direction. This is a worldwide existential threat that affects every living thing on Earth. It often compounds upon itself, so delays in reducing emissions of fossil fuels are shortening the amount of time remaining to eliminate the use of fossil fuels to preserve a livable planet. Nationalism often impedes solutions to this problem (among many others), as nations place their singular needs above the common good. Our initial proposal got around, and abstracts on many subjects arrived. Within a few weeks, we had enough good material for a 100,000-word book. The book then fattened to two moderate volumes and then to four two very hefty tomes. We tried several different titles as good submissions swelled. We also discovered that our best contributors were experts in their fields, which ranged the world. We settled on three stand-alone books:” 1/ nationalism and racial justice. Our first volume grew as the growth of Black Lives Matter following the brutal killing of George Floyd ignited protests over police brutality and other issues during 2020, following the police assassination of Floyd in Minneapolis. It is estimated that more people took part in protests of police brutality during the summer of 2020 than any other series of marches in United States history. This includes upheavals during the 1960s over racial issues and against the war in Southeast Asia (notably Vietnam). We choose a volume on racism because it is one of nationalism’s main motive forces. This volume provides a worldwide array of work on nationalism’s growth in various countries, usually by authors residing in them, or in the United States with ethnic ties to the nation being examined, often recent immigrants to the United States from them. Our roster of contributors comprises a small United Nations of insightful, well-written research and commentary from Indonesia, New Zealand, Australia, China, India, South Africa, France, Portugal, Estonia, Hungary, Russia, Poland, Kazakhstan, Georgia, and the United States. Volume 2 (this one) describes and analyzes nationalism, by country, around the world, except for the United States; and 3/material directly related to President Donald Trump, and the United States. The first volume is under consideration at the Texas A & M University Press. The other two are under contract to Nova Science Publishers (which includes social sciences). These three volumes may be used individually or as a set. Environmental material is taken up in appropriate places in each of the three books. * * * * * What became the United States of America has been strongly nationalist since the English of present-day Massachusetts and Jamestown first hit North America’s eastern shores. The country propelled itself across North America with the self-serving ideology of “manifest destiny” for four centuries before Donald Trump came along. Anyone who believes that a Trumpian affection for deportation of “illegals” is a new thing ought to take a look at immigration and deportation statistics in Adam Goodman’s The Deportation Machine: America’s Long History of Deporting Immigrants (Princeton University Press, 2020). Between 1920 and 2018, the United States deported 56.3 million people, compared with 51.7 million who were granted legal immigration status during the same dates. Nearly nine of ten deportees were Mexican (Nolan, 2020, 83). This kind of nationalism, has become an assassin of democracy as well as an impediment to solving global problems. Paul Krugman wrote in the New York Times (2019:A-25): that “In their 2018 book, How Democracies Die, the political scientists Steven Levitsky and Daniel Ziblatt documented how this process has played out in many countries, from Vladimir Putin’s Russia, to Recep Erdogan’s Turkey, to Viktor Orban’s Hungary. Add to these India’s Narendra Modi, China’s Xi Jinping, and the United States’ Donald Trump, among others. Bit by bit, the guardrails of democracy have been torn down, as institutions meant to serve the public became tools of ruling parties and self-serving ideologies, weaponized to punish and intimidate opposition parties’ opponents. On paper, these countries are still democracies; in practice, they have become one-party regimes….And it’s happening here [the United States] as we speak. If you are not worried about the future of American democracy, you aren’t paying attention” (Krugmam, 2019, A-25). We are reminded continuously that the late Carl Sagan, one of our most insightful scientific public intellectuals, had an interesting theory about highly developed civilizations. Given the number of stars and planets that must exist in the vast reaches of the universe, he said, there must be other highly developed and organized forms of life. Distance may keep us from making physical contact, but Sagan said that another reason we may never be on speaking terms with another intelligent race is (judging from our own example) could be their penchant for destroying themselves in relatively short order after reaching technological complexity. This book’s chapters, introduction, and conclusion examine the worldwide rise of partisan nationalism and the damage it has wrought on the worldwide pursuit of solutions for issues requiring worldwide scope, such scientific co-operation public health and others, mixing analysis of both. We use both historical description and analysis. This analysis concludes with a description of why we must avoid the isolating nature of nationalism that isolates people and encourages separation if we are to deal with issues of world-wide concern, and to maintain a sustainable, survivable Earth, placing the dominant political movement of our time against the Earth’s existential crises. Our contributors, all experts in their fields, each have assumed responsibility for a country, or two if they are related. This work entwines themes of worldwide concern with the political growth of nationalism because leaders with such a worldview are disinclined to co-operate internationally at a time when nations must find ways to solve common problems, such as the climate crisis. Inability to cooperate at this stage may doom everyone, eventually, to an overheated, stormy future plagued by droughts and deluges portending shortages of food and other essential commodities, meanwhile destroying large coastal urban areas because of rising sea levels. Future historians may look back at our time and wonder why as well as how our world succumbed to isolating nationalism at a time when time was so short for cooperative intervention which is crucial for survival of a sustainable earth. Pride in language and culture is salubrious to individuals’ sense of history and identity. Excess nationalism that prevents international co-operation on harmful worldwide maladies is quite another. As Pope Francis has pointed out: For all of our connectivity due to expansion of social media, ability to communicate can breed contempt as well as mutual trust. “For all our hyper-connectivity,” said Francis, “We witnessed a fragmentation that made it more difficult to resolve problems that affect us all” (Horowitz, 2020, A-12). The pope’s encyclical, titled “Brothers All,” also said: “The forces of myopic, extremist, resentful, and aggressive nationalism are on the rise.” The pope’s document also advocates support for migrants, as well as resistance to nationalist and tribal populism. Francis broadened his critique to the role of market capitalism, as well as nationalism has failed the peoples of the world when they need co-operation and solidarity in the face of the world-wide corona virus pandemic. Humankind needs to unite into “a new sense of the human family [Fratelli Tutti, “Brothers All”], that rejects war at all costs” (Pope, 2020, 6-A). Our journey takes us first to Russia, with the able eye and honed expertise of Richard D. Anderson, Jr. who teaches as UCLA and publishes on the subject of his chapter: “Putin, Russian identity, and Russia’s conduct at home and abroad.” Readers should find Dr. Anderson’s analysis fascinating because Vladimir Putin, the singular leader of Russian foreign and domestic policy these days (and perhaps for the rest of his life, given how malleable Russia’s Constitution has become) may be a short man physically, but has high ambitions. One of these involves restoring the old Russian (and Soviet) empire, which would involve re-subjugating a number of nations that broke off as the old order dissolved about 30 years ago. President (shall we say czar?) Putin also has international ambitions, notably by destabilizing the United States, where election meddling has become a specialty. The sight of Putin and U.S. president Donald Trump, two very rich men (Putin $70-$200 billion; Trump $2.5 billion), nuzzling in friendship would probably set Thomas Jefferson and Vladimir Lenin spinning in their graves. The road of history can take some unanticipated twists and turns. Consider Poland, from which we have an expert native analysis in chapter 2, Bartosz Hlebowicz, who is a Polish anthropologist and journalist. His piece is titled “Lawless and Unjust: How to Quickly Make Your Own Country a Puppet State Run by a Group of Hoodlums – the Hopeless Case of Poland (2015–2020).” When I visited Poland to teach and lecture twice between 2006 and 2008, most people seemed to be walking on air induced by freedom to conduct their own affairs to an unusual degree for a state usually squeezed between nationalists in Germany and Russia. What did the Poles then do in a couple of decades? Read Hlebowicz’ chapter and decide. It certainly isn’t soft-bellied liberalism. In Chapter 3, with Bruce E. Johansen, we visit China’s western provinces, the lands of Tibet as well as the Uighurs and other Muslims in the Xinjiang region, who would most assuredly resent being characterized as being possessed by the Chinese of the Han to the east. As a student of Native American history, I had never before thought of the Tibetans and Uighurs as Native peoples struggling against the Independence-minded peoples of a land that is called an adjunct of China on most of our maps. The random act of sitting next to a young woman on an Air India flight out of Hyderabad, bound for New Delhi taught me that the Tibetans had something to share with the Lakota, the Iroquois, and hundreds of other Native American states and nations in North America. Active resistance to Chinese rule lasted into the mid-nineteenth century, and continues today in a subversive manner, even in song, as I learned in 2018 when I acted as a foreign adjudicator on a Ph.D. dissertation by a Tibetan student at the University of Madras (in what is now in a city called Chennai), in southwestern India on resistance in song during Tibet’s recent history. Tibet is one of very few places on Earth where a young dissident can get shot to death for singing a song that troubles China’s Quest for Lebensraum. The situation in Xinjiang region, where close to a million Muslims have been interned in “reeducation” camps surrounded with brick walls and barbed wire. They sing, too. Come with us and hear the music. Back to Europe now, in Chapter 4, to Portugal and Spain, we find a break in the general pattern of nationalism. Portugal has been more progressive governmentally than most. Spain varies from a liberal majority to military coups, a pattern which has been exported to Latin America. A situation such as this can make use of the term “populism” problematic, because general usage in our time usually ties the word into a right-wing connotative straightjacket. “Populism” can be used to describe progressive (left-wing) insurgencies as well. José Pinto, who is native to Portugal and also researches and writes in Spanish as well as English, in “Populism in Portugal and Spain: a Real Neighbourhood?” provides insight into these historical paradoxes. Hungary shares some historical inclinations with Poland (above). Both emerged from Soviet dominance in an air of developing freedom and multicultural diversity after the Berlin Wall fell and the Soviet Union collapsed. Then, gradually at first, right wing-forces began to tighten up, stripping structures supporting popular freedom, from the courts, mass media, and other institutions. In Chapter 5, Bernard Tamas, in “From Youth Movement to Right-Liberal Wing Authoritarianism: The Rise of Fidesz and the Decline of Hungarian Democracy” puts the renewed growth of political and social repression into a context of worldwide nationalism. Tamas, an associate professor of political science at Valdosta State University, has been a postdoctoral fellow at Harvard University and a Fulbright scholar at the Central European University in Budapest, Hungary. His books include From Dissident to Party Politics: The Struggle for Democracy in Post-Communist Hungary (2007). Bear in mind that not everyone shares Orbán’s vision of what will make this nation great, again. On graffiti-covered walls in Budapest, Runes (traditional Hungarian script) has been found that read “Orbán is a motherfucker” (Mikanowski, 2019, 58). Also in Europe, in Chapter 6, Professor Ronan Le Coadic, of the University of Rennes, Rennes, France, in “Is There a Revival of French Nationalism?” Stating this title in the form of a question is quite appropriate because France’s nationalistic shift has built and ebbed several times during the last few decades. For a time after 2000, it came close to assuming the role of a substantial minority, only to ebb after that. In 2017, the candidate of the National Front reached the second round of the French presidential election. This was the second time this nationalist party reached the second round of the presidential election in the history of the Fifth Republic. In 2002, however, Jean-Marie Le Pen had only obtained 17.79% of the votes, while fifteen years later his daughter, Marine Le Pen, almost doubled her father's record, reaching 33.90% of the votes cast. Moreover, in the 2019 European elections, re-named Rassemblement National obtained the largest number of votes of all French political formations and can therefore boast of being "the leading party in France.” The brutality of oppressive nationalism may be expressed in personal relationships, such as child abuse. While Indonesia and Aotearoa [the Maoris’ name for New Zealand] hold very different ranks in the United Nations Human Development Programme assessments, where Indonesia is classified as a medium development country and Aotearoa New Zealand as a very high development country. In Chapter 7, “Domestic Violence Against Women in Indonesia and Aotearoa New Zealand: Making Sense of Differences and Similarities” co-authors, in Chapter 8, Mandy Morgan and Dr. Elli N. Hayati, from New Zealand and Indonesia respectively, found that despite their socio-economic differences, one in three women in each country experience physical or sexual intimate partner violence over their lifetime. In this chapter ther authors aim to deepen understandings of domestic violence through discussion of the socio-economic and demographic characteristics of theit countries to address domestic violence alongside studies of women’s attitudes to gender norms and experiences of intimate partner violence. One of the most surprising and upsetting scholarly journeys that a North American student may take involves Adolf Hitler’s comments on oppression of American Indians and Blacks as he imagined the construction of the Nazi state, a genesis of nationalism that is all but unknown in the United States of America, traced in this volume (Chapter 8) by co-editor Johansen. Beginning in Mein Kampf, during the 1920s, Hitler explicitly used the westward expansion of the United States across North America as a model and justification for Nazi conquest and anticipated colonization by Germans of what the Nazis called the “wild East” – the Slavic nations of Poland, the Baltic states, Ukraine, and Russia, most of which were under control of the Soviet Union. The Volga River (in Russia) was styled by Hitler as the Germans’ Mississippi, and covered wagons were readied for the German “manifest destiny” of imprisoning, eradicating, and replacing peoples the Nazis deemed inferior, all with direct references to events in North America during the previous century. At the same time, with no sense of contradiction, the Nazis partook of a long-standing German romanticism of Native Americans. One of Goebbels’ less propitious schemes was to confer honorary Aryan status on Native American tribes, in the hope that they would rise up against their oppressors. U.S. racial attitudes were “evidence [to the Nazis] that America was evolving in the right direction, despite its specious rhetoric about equality.” Ming Xie, originally from Beijing, in the People’s Republic of China, in Chapter 9, “News Coverage and Public Perceptions of the Social Credit System in China,” writes that The State Council of China in 2014 announced “that a nationwide social credit system would be established” in China. “Under this system, individuals, private companies, social organizations, and governmental agencies are assigned a score which will be calculated based on their trustworthiness and daily actions such as transaction history, professional conduct, obedience to law, corruption, tax evasion, and academic plagiarism.” The “nationalism” in this case is that of the state over the individual. China has 1.4 billion people; this system takes their measure for the purpose of state control. Once fully operational, control will be more subtle. People who are subject to it, through modern technology (most often smart phones) will prompt many people to self-censor. Orwell, modernized, might write: “Your smart phone is watching you.” Ming Xie holds two Ph.Ds, one in Public Administration from University of Nebraska at Omaha and another in Cultural Anthropology from the Chinese Academy of Social Sciences, Beijing, where she also worked for more than 10 years at a national think tank in the same institution. While there she summarized news from non-Chinese sources for senior members of the Chinese Communist Party. Ming is presently an assistant professor at the Department of Political Science and Criminal Justice, West Texas A&M University. In Chapter 10, analyzing native peoples and nationhood, Barbara Alice Mann, Professor of Honours at the University of Toledo, in “Divide, et Impera: The Self-Genocide Game” details ways in which European-American invaders deprive the conquered of their sense of nationhood as part of a subjugation system that amounts to genocide, rubbing out their languages and cultures -- and ultimately forcing the native peoples to assimilate on their own, for survival in a culture that is foreign to them. Mann is one of Native American Studies’ most acute critics of conquests’ contradictions, and an author who retrieves Native history with a powerful sense of voice and purpose, having authored roughly a dozen books and numerous book chapters, among many other works, who has traveled around the world lecturing and publishing on many subjects. Nalanda Roy and S. Mae Pedron in Chapter 11, “Understanding the Face of Humanity: The Rohingya Genocide.” describe one of the largest forced migrations in the history of the human race, the removal of 700,000 to 800,000 Muslims from Buddhist Myanmar to Bangladesh, which itself is already one of the most crowded and impoverished nations on Earth. With about 150 million people packed into an area the size of Nebraska and Iowa (population less than a tenth that of Bangladesh, a country that is losing land steadily to rising sea levels and erosion of the Ganges river delta. The Rohingyas’ refugee camp has been squeezed onto a gigantic, eroding, muddy slope that contains nearly no vegetation. However, Bangladesh is majority Muslim, so while the Rohingya may starve, they won’t be shot to death by marauding armies. Both authors of this exquisite (and excruciating) account teach at Georgia Southern University in Savannah, Georgia, Roy as an associate professor of International Studies and Asian politics, and Pedron as a graduate student; Roy originally hails from very eastern India, close to both Myanmar and Bangladesh, so he has special insight into the context of one of the most brutal genocides of our time, or any other. This is our case describing the problems that nationalism has and will pose for the sustainability of the Earth as our little blue-and-green orb becomes more crowded over time. The old ways, in which national arguments often end in devastating wars, are obsolete, given that the Earth and all the people, plants, and other animals that it sustains are faced with the existential threat of a climate crisis that within two centuries, more or less, will flood large parts of coastal cities, and endanger many species of plants and animals. To survive, we must listen to the Earth, and observe her travails, because they are increasingly our own.

AbstractThe water saving lock layout plays a key role in addressing the navigation hydraulic problems with high dams. However, the study of the propagation and development of nonlinear long waves induced by ship-lock operation in a water saving basin has received less attention so far. Specially, the mechanisms governing the formation of secondary waves and the impact of these waves on the impoundments of the basin are still not fully understood. In the present study the entire evolution of a nonlinear long wave in a water saving basin was numerically simulated. The wave shape, wave celerity and wave force were analyzed. It was found that the leading edge of a long wave propagated along the water saving basin with a celerity which varied with time and space. Two distinct stages could be recognized and defined: a rapid acceleration phase characterized by a sharp increase in the celerity with propagation distance and a gentle acceleration phase where the long wave propagated in a more gradual manner. Moreover, the water surface slop of a long wave front equal to 0.045 could be used as an estimate of the occurrence of secondary waves. Furthermore, the present results highlighted the wave force on the impoundments of a water saving basin was controlled by wave nonlinearity. These results may provide theoretical guidance and technical support for the hydraulic design and operation of water saving locks.

Rock slopes developed in granite may take different forms, as reflected in their longitudinal profiles. Field observations and a literature survey (e.g. Dumanowski, 1964; Young, 1972) allow us to distinguish at least five major categories of slopes: straight, convex-upward, concave, stepped, and vertical rock walls. In addition, overhang slopes may occur, but their height is seldom more than 10 m high and their occurrence is very localized. These basic categories may combine to form compound slopes, for example convex-upward in the upper part and vertical towards the footslope. Somewhat different is Young’s (1972) attempt to identify most common morphologies of granite slopes. He lists six major categories: (1) bare rock domes, smoothly rounded or faceted; (2) steep and irregular bare rock slopes of castellated residual hills, tending towards rectangular forms; (3) concave slopes crowned by a free face; (4) downslope succession of free face, boulder-covered section and pediment; (5) roughly straight or concave slopes, but having irregular, stepped microrelief; (6) smooth convex-concave profile with a continuous regolith cover. The latter, lacking any outcrops of sound bedrock, are not considered as rock slopes for the purposes of this section. Young (1972) appears to seek explanation of this variety in climatic differences between regions, claiming that ‘Variations of slope form associated with climatic differences are as great as or greater, on both granite and limestone, than the similarity of form arising from lithology’ (Young, 1972: 219). This is a debatable statement and apparently contradicted by numerous field examples of co-existence of different forms in relatively small areas. Slope forms do not appear specifically subordinate to larger landforms but occur in different local and regional geomorphic settings. For example, the slopes of the Tenaya Creek valley in the Yosemite National Park include, in different sections of the valley, straight, vertical, convex-upward, and concave variants (Plate 5.1). Apparently, multiple glaciation was unable to give the valley a uniform cross-sectional shape.

Analyze the force of fire smoke in a double-slope coupled V-shaped tunnel to study the influence of tunnel slope, the distance between the change slope point and the fire source on fire wind pressure, determine the basic characteristics of smoke movement, and use numerical simulation to spread the smoke authenticating. The results of the study show that when the smoke spreads to the left (upstream) of the slope change point of the tunnel, and with the increase of the slope, the temperature of the upstream top plate gradually decreases to the ambient temperature, and the smoke layer shows a parallel motion with the tunnel roof. When the tunnel slope reaches more than 10%, the roof temperature drops to the ambient temperature at 5m upstream; the upstream flow decreases with the slope. When the smoke is only in the tunnel to the right of the slope change point, the upstream smoke moves parallel to the horizontal plane. The slope is inversely related to the smoke backlash length, and when the slope is greater than 7%, the smoke backlash length is not sensitive to the change of fire source location.

In this study, the effect of earthquakes, beginning on 28 December 2020, on dropout doline development in the environs of Mečenčani and Borojevići was investigated. For that purpose, the shape of the doline, the inclination of the bearing surface and the rate of doline development were determined. A further analysis involved the characteristics of groundwater in the environs of the dolines and a functional relationship between the depth and the diameter of the dolines was sought. A model is proposed for the failure of the ceiling of cover cavities without support. The intensity of doline development is explained by favourable environment (dual cavity system, low inclination of the bearing surface, the presence and fluctuation of groundwater, etc.), the direct effect of earthquakes (material failure induced by earthquakes) and by their indirect effect (the partial solifluction of the ceiling material, lowered groundwater level).

The process of modelling and replicating extreme fire behaviour like junction fire is essential for understanding the phenomena associated with extreme fires. Numerical simulations of junction fires, replicating laboratory-scale experiments, with no imposed wind, were performed for a shrub fuel bed with slopes ranging from 0° to 30°. The simulations of junction fires were conducted for two junction angles 30° and 45°. For each scenario, the sensitivity to a range of numerical and physical parameters was investigated. The rate of spread (ROS) is a key parameter for assessing risks from vegetation fires. Experimental spreading junction fires, conducted at laboratory scale at Coimbra University (Portugal), were simulated using FIRESTAR3D - a three-dimensional physics-based fire model. To ensure the robustness of simulations, sensitivity analyses were carried out by varying the grid resolution, domain size, different fuel characteristics, as well as some of the thermo-physical parameters. The corresponding simulations were carried out using a single and two descriptions levels of the shrub: the vegetation was represented using only one cylindrical-shaped solid-fuel type (excelsior fuel using the characteristic parameters for Erica shrub), or two fuel by adding the contribution of twigs of various diameters up to 6 mm while keeping the same packing ratio. Finally, the validation of FIRESTAR3D simulations was achieved through the comparison of predicted and measured ROS values. The experimental trends of the compared quantities were well reproduced by the simulations. Accelerating and decelerating propagation phases were observed in all simulations, with a dependence on the slope angle, while the maximum rate of spread depends critically on the junction angle. As it was the case of other wildfires simulated by FIRESTAR3D, it was found that this fully-physical model is capable of simulating junction fire propagation. There are several processes associated with the development of a junction fire behaviour, in which dramatic changes in fire behaviour can occur with little change in various fuel, weather and topographical parameters. In a subsequent study, we aim to develop an understanding of junction fire behaviour taking into account essential parameters that affect the behaviour, namely: slope, junction angle, and driving wind velocity.

My first direct encounter with feng-shui came soon after I arrived in Hong Kong in 1965. A new hospital was being built on a hill overlooking Castle Peak Bay, where my family and I lived. The hospital foundations cut deep into the slope. Several old peasants told me, “This is very bad; the construction has cut the dragon’s pulse.” I learned that the hill had a dragon in it, whose blood circulation had been cut by the foundation trench. This seemed strange to me. I noted it down as a fascinating local belief, and thought no more of it. Soon afterward, a typhoon dumped two feet of rain on Hong Kong within a few days. The oversteepened, undercut slope failed, and a torrent of mud descended, washing out the hospital foundations and burying a house or two at the hill foot. “See?” said my friends. “This is what happens when you cut the dragon’s pulse.” A light went on in my head. The Chinese peasants, pragmatic to the core, had described the phenomenon in terms strange to me; but the phenomenon they described was perfectly real. I reflected that the geologists’ terms “oversteepening” and “slope failure” were not much more empirically verifiable than the dragon. Any Chinese peasant would find them even stranger than I had found that eminent serpent, since I had already learned from reading that ancient Chinese saw dragons in the scaly, ridged contours of mountain ranges. As time went on, I learned that I had found more than a different way of talking about obvious facts. Chinese site planning seemed more and more rational. I learned that villages protected the groves of trees that ringed them, because trees attract good influences and also provide shade, firewood, fruit, leafmold, timber, and other goods. I learned that roads to villages were made crooked to discourage evil beings—and that the evil beings included not only demons but also soldiers, government officials, and (other) bandits.

This chapter explores the law’s commitment to preserving the existing norms and practices that shape courtship, sex, and marriage. Judges are much less likely to provide remedies for examples of intimate deception they believe are commonplace and more likely to give remedies in cases they think are deviant and unusual. When judges assume that many forms of deceit are typical in courtship, sex, and marriage, they help make that so—normalizing the deception by protecting it from legal disapproval and redress. This dedication to safeguarding ordinary deception in intimate relationships has also functioned to protect extraordinary deceit. Courts have sometimes denied remedies for admittedly egregious intimate deception out of concern that providing redress might create a slippery slope that would ultimately jeopardize more ordinary deceivers. Indeed, the judicial commitment to shielding commonplace intimate deception has even helped defendants who deceived business competitors or government officials.

The southern Piedmont Region (north-west Italy) is characterized by a hilly zone called “Langhe” that covers an area of about 2300 km2 and is bordered by Tanaro River at north and west, by Orba River at east, and by Apennine mountains at south. The Langhe is rolling hills famous for their excellent wine, populated by many small inhabited centers since ancient times. An idea of the Langhe geomorphology can be gained by studying the word “Langa”: it may have been derived from either “landa,” which means a wild and uninhabited place or from “lingua,” which means a strip of land. The morphology of the Langhe hills is characterized by asymmetrical valleys with steep south-east facing slopes and more gentle north-west facing slopes: their profile is defined “saw toothed” by local inhabitants. The asymmetric shape is clearly conditioned by the geology. Severe hydrological events occurred in the last 100 years in Piedmont in particular on May 1926, February and March 1972, February 1974, and November 1994. During these long rainy periods, on the gentler slopes, translational rock-block slides involve tertiary flyschoid complexes represented by rhythmic series of deposits with varied grain size. These landslides often damage or destroy buildings and roads, even if rarely claim human lives.

This chapter considers the impact of Native-owned corporations on the Arctic Refuge debate. It traces the history of the Alaska Native Claims Settlement Act (ANCSA)—a controversial federal law passed in 1971 that established Native corporations as the instruments for land claims rather than tribal governments. The settlement was explicitly tied to an assimilationist agenda, imposing a corporate model on Indigenous communities. The chapter explains how the Arctic Slope Regional Corporation and the Kaktovic Iñupiat Corporation (both created following ANCSA) have shaped the Arctic Refuge debate and contributed to a simple media framing of the fight as a story of Gwich’in versus Iñupiat. The chapter complicates and challenges this narrative by including voices of Iñupiat, such as Robert Thompson, opposed to drilling and of other Indigenous critics of ANCSA, such as Faith Gemmill. It explains how leaders of Native corporations often present themselves as the voices and representatives of their communities. In addition, the chapter discusses Thomas Berger’s study of the effects of ANCSA, based on testimony from more than sixty villages across Alaska.

The foregoing chapters detail the many technical innovations in water supply, distribution, and management for several Old World, New World, and South- East Asian societies. For most of the New World’s societies, basic water resource problems evolved around securing their agricultural base given the unique environmental and water resource conditions prevalent in their locations. Diverse New World societies occupying different environment niches from dry coastal margins to wet highlands, often subject to vastly different average temperatures, crop types, and water variation cycles, were shown to devise different approaches to the development of their agricultural bases. While rainfall runoff from mountain watersheds sourced the many rivers of coastal Peruvian valleys and provided the basis for canal irrigation, excessive rainfall and cold in Andean highland locations allowed groundwater-based farming using raised Welds that had thermodynamic advantages based on conservation of the sun’s heat to prevent root crop destruction during freezing nights. The presence of varying climate cycles (excessive rainfall and drought) was seen to influence modifications in coastal canal systems. Alterations in canal size and placement to accommodate reduced-water supplies were evident in intravalley coastal systems where modifications were relatively straightforward in sandy environments. Intervalley water transfers through massive canal systems were a further characteristic of a flexible response to maintain the water resource base and this often involved the transfer of river water from one valley to another depending on agricultural, economic, and political priorities. With increased need for more agricultural lands to meet population demands, increasingly lower slope canals were surveyed to include further downslope lands. Here technical innovation was a key factor in providing surveying expertise to maintain low-slope contour canals. While such canals are found at very early Formative and Preceramic sites, surveying techniques became more refined in time to permit greater use of land areas reachable by low-slope canals. Here both Old and New World societies share their dependence on surveying technology to meet water transfer demands. While Roman surveying favoured the most direct aqueduct routing necessitating long, linear aqueduct structures interspersed with siphons and multitier aqueducts structures where appropriate, New World surveying was different in that canal designs following landscape contours were prevalent and, in some cases, optimized to produce specific and/or maximum flow rate designs. Specific measures to create hydraulic control structures to defend against El Niño destruction are evident in the New World archaeological record indicating an active, innovative engineering response to climate and weather-induced disasters, probably based on the memory of prior destructive events.

While structural damage detection based on flexural vibration shapes, such as mode shapes and steady-state response shapes under harmonic excitation, has been well developed, little attention is paid to that based on longitudinal vibration shapes that also contain damage information. This study originally formulates a slope vibration shape for damage detection in bars using longitudinal vibration shapes. To enhance noise robustness of the method, a slope vibration shape is transformed to a multiscale slope vibration shape in a multiscale domain using wavelet transform, which has explicit physical implication, high damage sensitivity, and noise robustness. These advantages are demonstrated in numerical cases of damaged bars, and results show that multiscale slope vibration shapes can be used for identifying and locating damage in a noisy environment. A three-dimensional (3D) scanning laser vibrometer is used to measure the longitudinal steady-state response shape of an aluminum bar with damage due to reduced cross-sectional dimensions under harmonic excitation, and results show that the method can successfully identify and locate the damage. Slopes of longitudinal vibration shapes are shown to be suitable for damage detection in bars and have potential for applications in noisy environments.

Atomic force microscopes (AFM) are widely used for feature detection and scanning surface topography of different materials. Contrast of topography images is significantly influenced by the sensitivity of AFM micro cantilever which means enhancement of sensitivity leads to increase of topography images resolution So, in the last years numerous scientists interested in studying the effects of different parameters such as geometric one on the sensitivity of AFM micro cantilevers. V-shape micro cantilever types of AFMs probe are widely used to scan various types of surfaces. In V-shape micro cantilevers, there are many geometric and design parameters which influence the flexural sensitivity of the micro beam, noticeably. In this paper evaluation of optimum geometric parameters and optimum cantilever slope is considered as a significant purpose in order to obtain maximum flexural sensitivity by using genetic algorithm optimization method. In the calculations, the normal and lateral interaction forces between AFM tip and sample surface is considered and modeled by linear springs which represent the contact stiffness of the sample surface. Also, a relation for flexural sensitivity of AFM cantilever as a function of geometric parameters and cantilever slope is derived which is used in optimization step by employing a genetic algorithm program. Using genetic algorithm method, the optimum geometric parameters and cantilever slope are calculated which maximize the flexural sensitivity of the first mode of a V-shape cantilever for various values of normal contact stiffness. These optimum parameters versus normal contact stiffness are presented in some result figures. The results show that for any contact stiffness, there are a cantilever slope and a set of geometrical parameters which provide the maximum sensitivity for AFM probe. Adopting these parameters for the design of V-shape micro cantilever according to the sample contact stiffness, maximum flexural sensitivity can be obtained, so that high contrast images are reachable.

Blazed grating features result in a modification to the Bragg which yields only a single output radiation mode (either substrate or cladding). [1]. Since blazing requires a triangular grating line shape, fabrication can be difficult. As a simplification, a discrete step approximation is often used to approximate a blazed structure. However, the discrete approximation requires multiple exposure steps making the fabrication process complex. The fabrication process can greatly simplified by approximating the blazed grating line shape by a periodic rectangular grating with a varying duty cycle [2]. Thus, the process used to fabricate periodic rectangular gratings can be used to fabricate the binary approximation of a blazed grating. Dividing the blazed grating structure into several (I), substructures, results in a substructure (i), each having a different discrete refractive index based on their location along the slope as shown in Figure 1.

Abstract This paper proposes a lumped parameter approach to simplify the modelling of a metamaterial based PEH to predict its energy harvesting performance around the fundamental resonance. The metamaterial based PEH consists of a host beam with a piezoelectric patch bonded at the clamped end. A series of local resonators are attached onto the host beam. In the first case study, the local resonators are modelled as mass-spring systems. By applying Rayleigh’s method and approximating the fundamental mode shape by the static deflection, the host beam is represented by a SDOF system. The equivalent lumped parameters are assumed to concentrate at the tip of the host beam and their explicit expressions are presented. Though the local resonators are identical, they have different influences on the host beam when being attached at different positions. To reflect the interaction degree (i.e., reacting force) between the local resonator and the host beam, a scaling factor that is a function of the attaching position is derived. On the other hand, due to the action of the local resonators, the fundamental mode shape of the host beam is actually changed. Based on the linear superposition principle, the static deflection approximated fundamental mode shape is corrected and the electromechanical coupling coefficient that is sensitive to the slope of the mode shape is updated to improve the accuracy. Based on the derived equivalent lumped parameters and correction factors, a multiple-degree-of-freedom (MDOF) model is constructed to predict the dynamic behavior of the metamaterial based PEH with mass-spring resonators. A corresponding finite element model is built to verify the developed MDOF model. In the second case study, the local resonators are modelled as practical parasitic beams. The parasitic beams are converted into equivalent lumped systems as well. However, the lumped parameters are the effective parameters at the beam tip. For the force interaction at the root of a parasitic beam, a factor is derived to correct the reaction force when a parasitic beam is represented by a SDOF mass-spring system. Using the reaction force correction factor, a MDOF model for the metamaterial based PEH with beam-like resonators is also established and verified by the finite element model.

Thermo-acoustic combustion instabilities have frequently been reported to occur when slight changes in operating conditions lead to significant and abrupt changes in flame shape or flame position, i.e. changes in the mode of flame stabilization. The present paper offers an explanation and mathematical model of this observation. The analysis rests on the assumption that changes in the mode of flame stabilization are accompanied by a significant variation of the pressure drop across burner and flame, such that the pressure drop - flow rate characteristic locally displays a negative slope. In the limit of low frequencies (Helmholtz mode), it is then straightforward to show that an oscillatory instability can result from such behavior. A stability criterion is derived, relating the non-dimensionalized gradient of the pressure drop characteristic to the Helmholtz number of the burner. The physics of the instability mechanism is explained, and it is observed that the Rayleigh criterion need not be satisfied for this kind of instability to occur. The analysis is then extended to higher frequencies and the transfer matrix for a burner with non-monotonic pressure drop is derived in the limit of low Mach number and negligible fluctuations of the rate of heat release. Experimental results obtained with an externally premixed swirl burner are presented. The pressure drop characteristic, the observed onset of instability and the instability frequency match very well the analytical predictions.

The groynes which are typical of shore protective structures can provide several aims. Although these structures may partly help to shoreline protection, they would also create some major problems in adjacent regions. Therefore the real performance of these structures needs to be considered carefully before going to construction. In this research, the effects of the cross shore and groyne wall slopes on flow pattern around an impermeable groyne were considered using a three-dimensional numerical CFD model (i.e., FLUENT). The widely accepted eddy viscosity concept and k-ε turbulence model were used to evaluate the Reynolds stresses and eddy viscosity coefficients, respectively. The finite volume method used in the software makes attractive flexibility to use any shape of grids to cover the cross and structural slopes in the computational domain. The model was first applied to a vertical groyne on a flat bed and the numerical model results were compared with experimental data. The model results of this numerical test showed a very good agreement with the corresponding experimental measurements, in terms of water elevation and velocity magnitudes. The model was then applied to a series of structures with different lateral slopes on various cross sectional bed slope. It was found that the flow pattern around the groyne was not changed significantly when the slopes of the structure and bed were slightly changed. The numerical model results, however, showed that by increasing the cross shore slope in any case of the lateral slope of the structure, the magnitude of the maximum velocity was decreased. The bed shear stresses were also decreased when the cross shore slope was increased. Moreover, these values were further decreased when the groyne-wall slope was reduced.

Dynamic atomic force microscopy (AFM) is an invaluable tool for characterizing and interacting with micro- and nano-scale systems. Standard measurement methods use a laser beam and a segmented photodiode to monitor the probe’s response. The diode reading is proportional to the slope of the probe and the displacement is obtained indirectly. As most operation methods use excitation around the fundamental frequency, calibration methods for determining the conversion factor to calculate the probe’s displacement are strongly inspired by the first vibrational mode shape. Within this paper, the results of an analytical study to predict measurement accuracy under non-standard excitation conditions with this calibration are presented. The influence of the excitation frequency, damping level, and laser spot location on this accuracy is investigated. The measurement accuracy for excitation at 2.5 times the fundamental frequency is of particular interest to the authors. Based upon the results, the use of a correction factor or a frequency-specific calibration is recommended.

One of the important issues to conduct the damage detection of a structure using vibration-based damage detection (VBDD) is not only to detect the damage but also to locate and quantify the damage. In this paper a systematic way of damage assessment, including identification of damage location and damage quantification, is proposed by using output-only measurement. Four level of damage identification algorithms are proposed. First, to identify the damage occurrence, null-space and subspace damage index are used. The eigenvalue difference ratio is also discussed for detecting the damage. Second, to locate the damage, the change of mode shape slope ratio and the prediction error from response using singular spectrum analysis are used. Finally, to quantify the damage the RSSI-COV algorithm is used to identify the change of dynamic characteristics together with the model updating technique, the loss of stiffness can be identified. Experimental data collected from the bridge foundation scouring in hydraulic lab was used to demonstrate the applicability of the proposed methods. The computation efficiency of each method is also discussed so as to accommodate the online damage detection.

Shallow foundation structures for offshore wind turbines offer ecological benefits compared to pile foundations as less noise is emitted at sea floor level during construction process. On the other hand, shallow offshore foundations can rarely be placed on top of the sea floor. Weak soils usually need to be excavated to place the foundation structure on more stable ground and thus, anthropogenic submarine slopes result. Steep but stable slopes meet both economic and ecologic aims as they minimise material movement and sediment disturbance. After Terzaghi [1] the angle β between slope and the horizontal of the ground surface of coarse-grained soil is at most equal to the critical state friction angle φc. However, it can be observed that natural submarine slopes of sandy soils are always much more shallow. Particularly fine-grained, cohesionless or almost cohesionless soils failed in the past, although the slope angle was much smaller than the critical state friction angle φc. Artificial (temporary) slopes do not appear and behave as natural submarine slopes, since the latter are already shaped by perpetual loads of waves, tide and mass movements. Physical simulations of different scales are used to analyse the stability of artificial submarine slopes with sandy soil of the North Sea. The study focuses on gravitational forces and impacts from the excavation processes. The simulations and theoretical considerations result in suggested slope angles for future shallow offshore foundations of wind farms in the North Sea.

Understanding the effects of gravity and wind loads on concentrating solar power (CSP) collectors is critical for performance calculations and developing more accurate alignment procedures and techniques. This paper presents a rigorous finite-element model of a parabolic trough collector that is used to determine the impact of gravity loads on bending and displacements of the mirror facets and support structure. The geometry of the LUZ LS-2 parabolic trough collector was modeled using SolidWorks, and gravity-induced loading and displacements were simulated in SolidWorks Simulation. The model of the trough collector was evaluated in two positions: the 90° position (mirrors facing upward) and the 0° position (mirrors facing horizontally). The slope errors of the mirror facet reflective surfaces were found by evaluating simulated angular displacements of node-connected segments along the mirror surface. The ideal (undeformed) shape of the mirror was compared to the shape of the deformed mirror after gravity loading. Also, slope errors were obtained by comparing the deformed shapes between the 90° and 0° positions. The slope errors resulting from comparison between the deformed vs. undeformed shape were as high as ∼2 mrad, depending on the location of the mirror facet on the collector. The slope errors resulting from a change in orientation of the trough from the 90° position to the 0° position with gravity loading were as high as ∼3 mrad, depending on the location of the facet.

We present a production economy with nominal price rigidities that explains several asset pricing facts, including a downward-sloping term structure of the equity premium, upward sloping term structures of nominal and real interest rates, and the cyclical variation of the term structures. In the model, after a productivity shock a countercyclical labor share exacerbates the procyclicality of dividends, and hence their riskiness, and generates countercyclical inflation. The dividend share gradually increases after a negative productivity shock as the price level increases sluggishly, so the payoffs of short-duration dividend claims (bonds) are more (less) procyclical than the payoffs of long-duration claims (bonds). A slow-moving external habit then produces large and countercyclical prices for these risks as well as high risk premia at very long horizons. In bad times, the slope of equity (bond) yields for the observable maturities becomes more negative (more positive), but risk premia also increase at longer horizons, and market equity premia end up increasing by more than short-run equity premia. The simultaneous presence of market and home consumption habits allows for uniting habits and a production economy without compromising the model’s ability to fit macroeconomic variables. The central bank’s anti-inflationary stance plays a key role in shaping equity and bond prices.

Quantitatively linking satellite observations of vegetation condition and climate data over time provides insight to climate influences on primary production, phenology (timing of growth), and sensitivity of vegetation to weather and longer-term patterns of weather referred to as climate. This in turn provides a basis for understanding potential climate impacts to vegetation—and the potential to anticipate cascading ecological effects—such as impacts to forage, habitat, fire potential, and erosion—as climate changes in the future. This report provides baseline information about vegetation production and condition over time at Canyonlands National Park (NP), as derived from satellite remote sensing. Its objective is to demonstrate methods of analysis, share findings, and document historic climate exposure and sensitivity of vegetation to weather and climate as a driver of vegetation change. This report represents a quantitative foundation of vegetation–climate relationships on an annual timestep. The methods can be modified to finer temporal resolution and other spatial scales if further analyses are needed to inform park planning and management. The knowledge provided in this report can inform vulnerability assessments for Climate Smart Conservation planning by park managers. Patterns of pivot points and responses can serve as a guide to anticipate what, where, when, and why vegetation change may occur. For this analysis, vegetation alliance groups were derived from vegetation-map polygons (Von Loh et al. 2007) by lumping vegetation types expected to respond similarly to climate. Relationships between vegetation production and phenology were evaluated for each alliance map unit larger than a satellite pixel (~300 × 300 m). We used a water-balance model to characterize the climate experienced by plants. Water balance translates temperature and precipitation into more biophysically relevant climate metrics, such as soil moisture and drought stress, that are often more strongly correlated with vegetation condition than temperature or precipitation are. By accounting for the interactions between temperature, precipitation, and site characteristics, water balance helps make regional climate assessments relevant to local scales. The results provide a foundation for interpreting weather and climate as a driver of changes in primary production over a 20-year period at the polygon and alliance-group scale. Additionally, they demonstrate how vegetation type and site characteristics, such as soil properties, slope, and aspect, interact with climate at local scales to determine trends in vegetation condition. This report quantitatively defines critical water needs of vegetation and identifies which alliance types, in which locations, may be most susceptible to climate-change impacts in the future. Finally, this report explains how findings can be used in the Climate Smart Conservation framework, with scenario planning, to help manage park resources through transitions imposed by climate change.

Quantitatively linking satellite observations of vegetation condition and climate data over time provides insight to climate influences on primary production, phenology (timing of growth), and sensitivity of vegetation to weather and longer-term patterns of weather referred to as climate. This in turn provides a basis for understanding potential climate impacts to vegetation—and the potential to anticipate cascading ecological effects, such as impacts to forage, habitat, fire potential, and erosion, as climate changes in the future. This report provides baseline information about vegetation production and condition over time at Capitol Reef National Park (NP), as derived from satellite remote sensing. Its objective is to demonstrate methods of analysis, share findings, and document historic climate exposure and sensitivity of vegetation to weather and climate as a driver of vegetation change. This report represents a quantitative foundation of vegetation–climate relationships on an annual timestep. The methods can be modified to finer temporal resolution and other spatial scales if further analyses are needed to inform park planning and management. The knowledge provided in this report can inform vulnerability assessments for Climate Smart Conservation planning by park managers. Patterns of pivot points and responses can serve as a guide to anticipate what, where, when, and why vegetation change may occur. For this analysis, vegetation alliance groups were derived from vegetation-map polygons (Von Loh et al. 2007) by lumping vegetation types expected to respond similarly to climate. Relationships between vegetation production and phenology were evaluated for each alliance map unit larger than a satellite pixel (~300 × 300 m). We used a water-balance model to characterize the climate experienced by plants. Water balance translates temperature and precipitation into more biophysically relevant climate metrics, such as soil moisture and drought stress, that are often more strongly correlated with vegetation condition than temperature or precipitation are. By accounting for the interactions between temperature, precipitation, and site characteristics, water balance helps make regional climate assessments relevant to local scales. The results provide a foundation for interpreting weather and climate as a driver of changes in primary production over a 20-year period at the polygon and alliance-group scale. Additionally, they demonstrate how vegetation type and site characteristics, such as soil properties, slope, and aspect, interact with climate at local scales to determine trends in vegetation condition. This report quantitatively defines critical water needs of vegetation and identifies which alliance types, in which locations, may be most susceptible to climate-change impacts in the future. Finally, this report explains how findings can be used in the Climate Smart Conservation framework, with scenario planning, to help manage park resources through transitions imposed by climate change.