Gotowa bibliografia na temat „Inorganic Hybrid Heterostructure Solar Cells”

The aim of this research is to study improvement of power conversion efficiency (PCE) of organic-inorganic hybrid bulk heterostructure solar cell prepared by rapid convective deposition as a function of concentration of zinc oxide additive. The structure of hybrid solar cell used in this research is ITO/ZnO/P3HT:PC70BM:ZnO(nanoparticles)/MoO3/Au. By adding 5 mg/ml of ZnO nanoparticles in the active layer (P3HT:PC70BM), the PCE was increased from 0.46 to 1.09%. In order to reveal the origin of improving efficiency, surface morphology and optical properties of active layers were investigated by atomic force microscopy (AFM) and UV-Visible spectroscopy, respectively. The results clearly indicate that the enhancement of solar cell efficiency results from (i) the proper phase sepharation of electron donor and acceptor in the active layer and (ii) the better absorption of the active layer. This research work introduces an alternative way to improve solar cell efficiency by adding ZnO into active layer.

This paper reports the fabrication and electrical characterization of hybrid organic-inorganic solar cell based on the deposition of polyaniline (PANI) on n-type GaAs substrate with three different crystal orientations namely Au/PANI/(100) n-GaAs/(Ni-Au), Au/PANI/(110) n-GaAs/(Ni-Au), and Au/PANI/(311)B n-GaAs/(Ni-Au) using spin coating technique. The effect of crystallographic orientation of n-GaAs on solar cell efficiency of the hybrid solar cell devices has been studied utilizing current density-voltage (J-V) measurements under illumination conditions. Additionally, the influence of planes of n-GaAs on the diode parameters of the same devices has been investigated by employing current-voltage (I-V) characteristics in the dark conditions at room temperature. The experimental observations showed that the best performance was obtained for solar cells fabricated with the structure of Au/PANI/(311)B n-GaAs/(Ni-Au). The open-circuit voltage (Voc), short circuit current density (Jsc), and solar cell efficiency () of the same device were shown the values of 342 mV, 0.294 mAcm-2, 0.0196%, respectively under illuminated condition. All the solar cell characteristics were carried out under standard AM 1.5 at room temperature. Also, diode parameters of PANI/(311)B n-GaAs heterostructures were calculated from the dark I-V measurements revealed the lower reverse saturation current (Io) of 3.0×10-9A, higher barrier height () of 0.79 eV and lower ideality factor (n) of 3.16.

Renewed interest has brought significant attention to tune coherently the electronic and optical properties of hybrid organic–inorganic perovskites (HOIPs) in recent years. Tailoring the intimate structure–property relationship is a primary target toward the advancement of light-harvesting technologies. These constructive progresses are expected to promote staggering endeavors within the solar cells community that needs to be revisited. Several considerations and strategies are introduced mainly to illustrate the importance of structural stability, interfacial alignment, and photo-generated carriers extraction across the perovskite heterostructures. Here, we review recent strides of such vast compelling diversity in order to shed some light on the interplay of the interfacial chemistry, photophysics, and light-emitting properties of HOIPs via molecular engineering or doping approach. In addition, we outline several fundamental knowledge processes across the role of charge transfer, charge carrier extraction, passivation agent, bandgap, and emission tunability at two-dimensional (2D) level of HOIPs/molecule heterointerfaces. An extensive range of the relevant work is illustrated to embrace new research directions for employing organic molecules as targeted active layer in perovskite-based devices. Ultimately, we address important insights related to the physical phenomena at the active molecules/perovskites interfaces that deserve careful considerations. This review specifically outlines a comprehensive overview of surface-based interactions that fundamentally challenges the delicate balance between organic materials and perovskites, which promotes bright future of desired practical applications.

Abstract Global fuel consumption and harmful gaseous emissions diverted energy sources to alternative means. Solar water splitting amidst other solar conversion methods is the most clean and efficient means of hydrogen production. 21st century technologies have delved into adopting nanomaterials of high efficiency to treat environmental pollution and produce hydrogen through electrochemical, photocatalytic, or electrophotocatalytic processes due to their outstanding properties. We reviewed diverse means of producing hydrogen through the use of advanced nanomaterials like carbon nanomaterials, solid inorganic-organic hybrids, metallic oxides/sulfides, quantum dots, composite heterostructures, microbial electrolysis cells etc. Overview on hydrogen production, ways of generating hydrogen, advanced nanomaterials for hydrogen production, and recent progress in hydrogen-producing nanomaterials have been discussed.

The paper presents a promising solution for photovoltaic modules that provides overcoming the main conceptual limitation for the concentrator concept in photovoltaics --- the impossibility to convert diffused (scattered) solar radiation coming to the panel of sunlight concentrators. The design of a hybrid concentrator-planar photovoltaic module based on heterostructure solar cells: A3B5 triple-junction and Si-HJT is presented. The results of initial outdoor studies of the module output characteristics are discussed and estimates of its energy efficiency are given. Keywords: hybrid concentrator-planar photovoltaic module, multijunction solar cell, Si-HJT planar photoconverter, diffusely scattered radiation.

AbstractWhen light is absorbed in organic semiconductors, bound electron–hole pairs known as excitons are generated. The electrons and holes separate from each other at an interface between two semiconductors by electron transfer. It is advantageous to form well-ordered nanostructures so that all of the excitons can reach the interface between the two semiconductors and all of the charge carriers have a pathway to the appropriate electrode. This article discusses charge and exciton transport in organic semiconductors, as well as the opportunities for making highly efficient solar cells and for using carbon nanotubes to replace metal oxide electrodes.

The purpose of this work is to develop organic/inorganic hybrid solar cells based on electroplated CdTe. The materials used in this research are CdS, CdTe and PAni. These materials have been characterised by XRD, Raman spectroscopy, EDX, SEM, AFM, UV-Vis spectroscopy, PEC, C-V and DC measurements, UPS and PL for their structural, compositional, morphological, optical, electrical and defect properties. CdS has electrodeposited from the electrolyte using (NH[4])[2]S[2]O[3] as the sulphur source. The optimum growth voltage (V[g]) and temperature (T[g]) are obtained at 1455 mV and 85°C, respectively. The best annealing condition is found to be at 400°C for 20 minutes in the presence of CdCl[2]+CdF[2]. CdTe thin films were electrodeposited from CdCl[2] precursor and a comprehensive study was carried out for the first time. The work has demonstrated a better understanding of material issues and some clues on the effect of CdCl[2] treatment. The optimum V[g] and annealing condition were obtained at 698 mV with respect to the calomel electrode and 420°C for 20 minutes in the presence of CdCl[2]+CdF[2] or CdCl[2]+CdF[2]+GaCl[3]. The development of PAni thin films has been established using anodic and cathodic deposition. The pernigraniline salt PAni grown from anodic has an amorphous structure, large bandgap and cementing growth effect while leucoemeraldine salt PAni grown from cathodic deposition shows the best crystallinity at V[g]=1654 mV with respect to carbon anode, smaller grain size, higher resistivity and lower bandgap. The CdS, CdTe and PAni thin films have been studied in device structures, assessing their solar cell device performance. The best of CdS/CdTe solar cell was observed with efficiency of 5.8% when using CdS thin film treated with CdCl[2]+CdF[2] at 400°C. The best solar cell from CdTe study shows the efficiency of 6.8% when using CdTe thin films treated with CdCl[2]+CdF[2] at 420°C. Further study demonstrates that a device with g/FTO/n-CdS(~200 nm)/n-CdTe(~1200 nm)/p-CdTe(~300 nm)/Au shows high J[sc] and highest efficiency (7.7%) due to the formation of n-n heterojunction, p-n homojuction and ohmic contact within the structure. The efficiency of the solar cell increased from -2.4% to -4.2% when incorporating -81 nm thick PAni layer grown from anodic deposition. The devices incorporating ZnS, ZnTe and CdSe layers show the prospect of graded bandgap solar cell, but proper optimisation on each material should be carried out before using in multi-layer device structures. The study on the lifetime of solar cells show slow degradation and it maintained more than 83% of its initial efficiency after 9,000 hours.

Solar energy as the most abundant source of energy is clean, non-pollutant, and completely renewable, which provides energy security, independence, and reliability. Organic-inorganic hybrid perovskite solar cells (PSCs) revolutionized the photovoltaics field not only by showing high efficiency of above 22% in just a few years but also by providing cheap and facile fabrication methods. In this dissertation, fabrication of PSCs in both ambient air conditions and environmentally controlled N2-filled glove-box are studied. Several characterization methods such as SEM, XRD, EDS, Profilometry, four-point probe measurement, EQE, and current-voltage measurements were employed to examine the quality of thin films and the performance of the PSCs. A few issues with the use of equipment for the fabrication of thin films are addressed, and the solutions are provided. It is suggested to fabricate PSCs in ambient air conditions entirely, to reduce the production cost. So, in this part, the preparation of the solutions, the fabrication of thin films, and the storage of materials were performed in ambient air conditions regardless of their humidity sensitivity. Thus, for the first part, the fabrication of PSCs in ambient air conditions with relative humidity above ~36% with and without moisture sensitive material, i.e., Li-TFSI are provided. Perovskite materials including MAPbI3 and mixed cation MAyFA(1-y)PbIxBr(1-x) compositions are investigated. Many solution-process parameters such as the spin-coating speed for deposition of the hole transporting layer (HTL), preparation of the HTL solution, impact of air and light on the HTL conductivity, and the effect of repetitive measurement of PSCs are investigated. The results show that the higher spin speed of PbI2 is critical for high-quality PbI2 film formation. The author also found that exposure of samples to air and light are both crucial for fabrication of solar cells with larger current density and better fill factor. The aging characteristics of the PSCs in air and vacuum environments are also investigated. Each performance parameter of air-stored samples shows a drastic change compared with that of the vacuum-stored samples, and both moisture and oxygen in air are found to influence the PSCs performances. These results are essential towards the fabrication of low-cost, high-efficiency PSCs in ambient air conditions. In the second part, the research is focused on the fabrication of high-efficiency PSCs using the glove-box. Both single-step and two-step spin-coating methods with perovskite precursors such as MAyFA(1-y)PbIxBr(1-x) and Cesium-doped mixed cation perovskite with a final formula of Cs0.07MA0.1581FA0.7719Pb1I2.49Br0.51 were considered. The effect of several materials and process parameters on the performance of PSCs are investigated. A new solution which consists of titanium dioxide (TiO2), hydrochloric acid (HCl), and anhydrous ethanol is introduced and optimized for fabrication of quick, pinhole-free, and efficient hole-blocking layer using the spin-coating method. Highly reproducible PSCs with an average power conversion efficiency (PCE) of 15.4% are fabricated using this solution by spin-coating method compared to the conventional solution utilizing both spin-coating with an average PCE of 10.6% and spray pyrolysis with an average PCE of 13.78%. Moreover, a thin layer of silver is introduced as an interlayer between the HTL and the back contact. Interestingly, it improved the current density and, finally the PCEs of devices by improving the adhesion of the back electrode onto the organic HTL and increasing the light reflection in the PSC. Finally, a highly reproducible fabrication procedure for cesium-doped PSCs using the anti-solvent method with an average PCE of 16.5%, and a maximum PCE of ~17.5% is provided.

Au catalyst ZnO nanostructures have been grown on the a- and c-plane sapphire substrate by PLD. Influence of substrate lattice orientation, substrate surface and different substrate annealing temperature have been characterized by AFM, SEM and XRD. This report shows that a-plane sapphire substrate annealed at 1000 degree C and 1200 degree C improves the growth condition of Au catalyst ZnO nanostructures. For c-plane sapphire; annealing at 1200 degree C and 1400 degree C enhances the nanostructure growth. The better growth condition is a result of the terrace-and-step morphology seen on the substrate surface prior to growth. This report also indicates a correlation between the azimuthal in-plane alignment of the grown nanostructures and the sapphire substrate lattice orientation.

[ES] Las perovskitas orgánicas-inorgánicas de haluros de metilamonio y plomo y sus mezclas han mostrado propiedades optoelectrónicas óptimas como absorbente ideal para aplicaciones fotovoltaicas. Los dispositivos solares basados en perovskita han evolucionado rápidamente, desde una eficiencia del 3.9% en 2009, al 22.7% en 2017 y con un coste de fabricación más bajo que las células solares de silicio. Una desventaja del uso de absorbentes de perovskita en dispositivos fotovoltaicos es su baja estabilidad. Las células con un alto rendimiento, pierden su eficiencia y se degradan rápidamente. Para poder producir estos materiales industrialmente es necesario realizar estudios en profundidad que mejoren la eficiencia y estabilidad. Una vía de mejora es la ingeniería composicional, estrategia que hemos empleado en la elaboración de esta tesis y que consiste en la investigación y mejora de las propiedades optoelectrónicas y morfológicas, derivadas de la sustitución y/o combinación de cationes y aniones, que constituyen el material de perovskita. Se sintetizaron polvos puros de perovskita de I, Br, Cl, a partir de los cuales se prepararon capas puras y mixtas MAPbX3-xYx, con el objetivo de mejorar sus propiedades optoelectrónicas y estructurales. Los análisis de difracción de rayos X mostraron las propiedades estructurales de los polvos cristalinos y capas puras y mixtas. Los análisis de UV-vis y fotoluminiscencia mostraron que el rango de absorción varía a lo largo del espectro visible en función del contenido del haluro en las capas. Los análisis de fotoluminiscencia y calorimetría diferencial de barrido muestran los cambios de fase de las perovskitas puras a distintas temperaturas, coincidiendo dichos cambios en ambos análisis. El análisis FESEM de las perovskitas puras mostró las diferencias morfológicas entre los polvos y capas. Siguiendo esta línea de investigación, se estudiaron con más detalle las perovskitas mixtas de yodo-bromo, con un contenido de bromo de hasta el 33%, consiguiendo ajustar el bandgap para evitar pérdidas en la absorción y mejorar las propiedades optoelectrónicas, estructurales y morfológicas. A pesar de las buenas propiedades optoelectrónicas de las perovskitas de metilamonio, el catión orgánico disminuye su estabilidad, lo que llevó a investigar otros cationes inorgánicos. Las perovskitas de cesio son una alternativa prometedora, y por esta razón hemos sintetizado capas finas de perovskitas de cesio mixtas, CsPbBr3-xIx, para determinar los efectos que produce la sustitución parcial del yodo en las propiedades físicas y la estabilidad. Se obtuvieron capas con una buena resistencia a la humedad y temperatura, favoreciendo su aplicación en el campo fotovoltaico. Se ha estudiado la sustitución parcial del catión de metilamonio con otros cationes orgánicos, como el guanidinio e imidiazolio. Se demostró que pequeñas cantidades de guanidinio mejoran la estabilidad de las capas y su morfología. Se estableció el límite de solubilidad del guanidinio en el 20%, aproximadamente, y se determinó la estructura cristalina de las mezclas. La intensidad del pico de fotoluminiscencia aumentó para mezclas por debajo del límite de solubilidad. Se obtuvieron resultados similares para la sustitución del metilamonio con pequeñas cantidades de imidazolio. Los análisis de rayos X establecieron el límite de solubilidad en aproximadamente el 10% y una mejora en la cristalinidad. Los resultados de fotoluminiscencia sugieren que pequeñas cantidades de imidazolio reducen significativamente las recombinaciones no radiativas, actuando como un pasivador efectivo. Finalmente, se muestra el proceso de fabricación de dispositivos basados en MAPbI3 y sintetizados en función de las condiciones ambientales y empleando el dietil éter como anti-solvente. Los dispositivos mostraron una eficiencia máxima del 14.73%. Se ha probado que la oxidación del spiro-OMeTAD, bajo condiciones cont
[FR] Les perovskites orgàniques-inorgàniques de halurs de metilamoni i plom i les seues mescles han mostrat propietats optoelectròniques òptimes com a absorbent ideal per a aplicacions fotovoltaiques. Els dispositius solars basats en perovskita han evolucionat ràpidament, passant d'una eficiència del 3.9% en 2009, fins al 22.7% en 2017, i amb un cost de fabricació més baix que les cèl·lules solars de silici. No obstant això, un dels desavantatges de l'ús de absorbents de perovskita és la baixa estabilitat. En general, les cèl·lules que mostren un alt rendiment, perden la seua eficiència i es degraden ràpidament. Per a que aquestos materials puguen ser produits industrialment a gran escala és necessari estudiar-los en profunditat per millorar la eficiència i estabilitat. Una de les vies de millora és l'enginyeria composicional, estratègia que hem emprat en l'elaboració d'aquesta tesi i que consisteix en la investigació i la millora de les propietats optoelectròniques i morfològiques, derivades de la substitució i/o combinació de cations i anions, que constitueixen el material de perovskita. S'han sintetitzat pols purs de perovskita per a I, Br, Cl, a partir d'els quals es van preparar capes pures i mixtes MAPbX3-xYx per a millorar les propietats optoelectròniques i estructurals. Mitjançant anàlisi de difracció de raigs X, s'estudiaren les propietats estructurals del pols cristalins i capes pures i mixtes. Els anàlisis d'UV-vis i fotoluminiscència, mostren que el rang d'absorció varia al llarg de l'espectre visible en funció del contingut de l'halur. Les anàlisis de fotoluminiscència i calorimetria diferencial mostren els canvis de fase de les perovskites pures a diferents temperatures, coincidint aquestos canvis en totes dues anàlisis. L'anàlisi FESEM de les perovskites pures, mostra les diferències morfològiques entre els pols i capes. Seguint aquesta línia d'investigació, s'estudiaren les perovskites mixtes de iode-brom, amb un contingut de brom de fins el 33%, ajustant el bandgap per a evitar pèrdues en l'absorció i millorar les propietats optoelectròniques, estructurals i morfològiques. Malgrat les bones propietats optoelectròniques de les perovskites de metilamoni, el catió orgànic disminueix la estabilitat, la qual cosa ha portat a investigar l'ús d'altres cations inorgànics. Les perovskites de cesi són una alternativa prometedora, i per aquesta raó hem sintetitzat capes fines de perovskites de cesi mixtes, CsPbBr3-xIx, per tal de determinar els efectes de la substitució parcial del iode en les propietats físiques i l'estabilitat. Es van obtenir capes amb una bona resistència a la humitat i a la temperatura, afavorint la seua aplicació en el camp fotovoltaic. S'ha estudiat també la substitució parcial del catió de metilamoni amb altres cations orgànics, com el guanidini i imidiazoli. S'ha demostrat que petites quantitats de guanidini milloren l'estabilitat i la morfologia de les capes. S'ha establert que el límit de solubilitat del guanidini es del 20%, aproximadament, i s'ha determinat l'estructura cristal·lina de les mescles. S'ha observat un augment en la intensitat del pic de fotoluminiscència per a mescles per sota del límit de solubilitat. Es van obtenir resultats similars per a la substitució del metilamoni amb petites quantitats de imidazoli. Les anàlisis de difracció de raigs X van establir el límit de solubilitat en aproximadament el 10% i una millora en la cristalinitat. Els resultats de fotoluminiscència suggereixen que petites quantitats de imidazoli redueixen les recombinacions no radiatives, actuant com un pasivador efectiu. Finalment, es mostra el procés de fabricació de dispositius basats en MAPbI3 i sintetitzats en funció de les condicions ambientals, especialment la humitat relativa i utilitzant el dietil èter com anti-solvent. Els dispositius van mostrar una eficiència màx
[EN] Organic-inorganic methylammonium lead halides perovskites and their mixtures have shown optimal optoelectronic properties as an ideal absorber for photovoltaic applications. In the last decade, solar devices based on perovskite have evolved rapidly, going from an initial efficiency of only 3.9% in 2009, to an efficiency of 22.7% in 2017 and being, at the same time, more cost-effective than silicon solar cells. However, one of the main disadvantages when using perovskite absorbents in photovoltaic devices is their low stability. In general, cells that show high performance lose their efficiency and degrade rapidly. For these materials to be scalable it is necessary to carry out in-depth studies aiming at improved efficiency and stability. One of the main sources to improve stability and efficiency is compositional engineering, a strategy employed in the elaboration of this thesis, consisting of the investigation and improvement of the optoelectronic and morphological properties, derived from the substitution and / or combination of cations and anions, which constitute the perovskite material. Pure powders of perovskite were synthesized, for I, Br, Cl, from which pure and mixed MAPbX3-xYx films were prepared in order to improve their optoelectronic and structural properties. By means of X-ray diffraction analysis, the structural properties of crystalline powders and pure and mixed films were studied. Employing UV-vis and photoluminescence analysis, it was observed that the absorption range varied along the visible spectrum as a function of the halide content in the thin films. Both, photoluminescence and differential scanning calorimetry analysis showed the changes of phase of the pure perovskites at different temperatures. FESEM characterization of the pure perovskites showed the morphological differences between the powders and the films. Following this line of research, mixed perovskites of iodine-bromine with a bromine content of up to 33% were studied in more detail. The bandgap was tuned to avoid significant losses in absorption and improve the optoelectronic, structural and morphological properties. Despite the excellent optoelectronic properties of the methylammonium perovskite, the presence of the organic cation decreases its stability, which prompted research into the use of other inorganic cations. Cesium perovskites, are a very promising alternative, and for this reason we synthesized thin films of mixed cesium perovskites, CsPbBr3-xIx, to determine the effects of the partial substitution of iodine on physical properties and stability. Films with a very good resistance to moisture and temperature were obtained, which will favor the application of this type of perovskites in the photovoltaic field. The partial replacement of the methylammonium cation with other organic cations, such as guanidinium and imidiazolium, was also studied, showing that small amounts of guanidinium significantly improve the stability of the films and their morphology. It was established that the solubility limit of guanidinium is approximately 20%, and the crystalline structure of the mixtures was determined. An increase in the intensity of the photoluminescence peak for mixtures below the solubility limit was observed. Similar results were obtained for the substitution of methylammonium with small amounts of imidazolium. X-ray diffraction analyzes established the solubility limit at approximately 10% and an improvement in crystallinity. Photoluminescence results suggest that small amounts of imidazolium significantly reduce nonradiative recombinations, acting as an effective passivator. Finally, the manufacturing process of devices based on MAPbI3 and synthesized according to environmental conditions, especially relative humidity and using diethyl ether as anti-solvent is shown. The devices presented a maximum efficiency of 14.73%, proving that the oxidation of spiro-OMeTAD, under controlled humidity conditions, can improve efficiency.
Vega Fleitas, E. (2018). Study and Characterization of Hybrid Organic-Inorganic Perovskites for Solar Cells Applications [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/113402
TESIS

Solar cells involving two different perovskites were manufactured and analyzed. The perovskites were (CH3NH3)PbI3 and (CH3NH3)SnI3. Both perovskites have a shared methyl ammonium group (MA) and are used as both light absorbing material and hole conducting material (HTM) in this project. The preparation procedures for the complete device were according to previous attempts to make stable organic-inorganic hybrid perovskites and involved different layers and procedures. Both perovskites were manufactured by mixing methyl ammonium iodide with either lead iodide or tin iodide in different concentrations. This was then deposited on a 600nm thick mesoporous TiO2 layer. Deposition of the hole-transporting material (HTM) was done by spin-coating 2,2´,7,7´-tetrakis-(N,N-dip-methoxyphenylamine) 9,9´-spirobifluorene, also called spiro-OMeTAD. Lastly thermal evaporation was used to deposit a silver electrode. Different measurements were done on the light absorbing materials. The lead perovskite solar cell device was subjected to illumination with Air Mass 1.5 sunlight (100mW/cm2) which produced an open circuit voltage Voc of 0.645 V, a short circuit photocurrent Jsc of about 7 mA/cm2, and a fill factor FF of 0.445. This resulted in a power conversion efficiency (PCE) of about 2% and an incident photon to current efficiency (IPCE) of up to 60%. The tin perovskite has not been used in solar cells before and the initial results presented here shows low performance using the same device construction as for the lead perovskite. However, the incident photon to electron conversion affirms that there is a current in the visible region, and IPCE of 12.5 % was observed at 375nm. UV-visible NIR measurement was used to analyze the light absorption of the perovskite structures and a broader light absorption was observed for the lead perovskite compared to the tin perovskite. X-ray diffraction (XRD) analyzing was done on both perovskite materials using different concentrations and both with and without nanoporous TiO2 film. Both perovskites demonstrate very similar peaks with some exceptions. Photo-induced absorption (PIA) measurement was used for the purpose of showing the magnitude of charge separation or hole transfer in the light absorbing material, both when using the perovskites as a light absorber and a hole conductor. This is measured by analyzing the hole injection from the excited light absorber into the HTM. Hole transfer was observed for the lead perovskite (when used as light absorber) and tin perovskite (when used as hole conductor).