Gotowe bibliografie tematyczne / 4H-SiC

Gotowa bibliografia na temat „4H-SiC”

Autor: Grafiati
Data publikacji: 4 czerwca 2021
Data aktualizacji: 10 marca 2023

Utwórz poprawne odniesienie w stylach APA, MLA, Chicago, Harvard i wielu innych

Wybierz rodzaj źródła:

Spis treści

Zobacz listy aktualnych artykułów, książek, rozpraw, streszczeń i innych źródeł naukowych na temat „4H-SiC”.

Przycisk „Dodaj do bibliografii” jest dostępny obok każdej pracy w bibliografii. Użyj go – a my automatycznie utworzymy odniesienie bibliograficzne do wybranej pracy w stylu cytowania, którego potrzebujesz: APA, MLA, Harvard, Chicago, Vancouver itp.

Możesz również pobrać pełny tekst publikacji naukowej w formacie „.pdf” i przeczytać adnotację do pracy online, jeśli odpowiednie parametry są dostępne w metadanych.

Artykuły w czasopismach na temat "4H-SiC"

1

Shilpa, A., S. Singh i N. V. L. Narasimha Murty. "Spectroscopic performance of Ni/4H-SiC and Ti/4H-SiC Schottky barrier diode alpha particle detectors". Journal of Instrumentation 17, nr 11 (1.11.2022): P11014. http://dx.doi.org/10.1088/1748-0221/17/11/p11014.

Pełny tekst źródła
Streszczenie:
Abstract Advancement in the growth of 4H-SiC with low micropipe densities (∼ 0.11 cm-2) in achieving high pure epitaxial layers, enabled the development of high-resolution 4H-SiC alpha particle Schottky radiation detectors for harsh environments. In particular, the study considers two types of 4H-SiC radiation detectors having Ni and Ti as Schottky contacts. They are fabricated by depositing Ni and Ti on 25 μm thick n-type 4H-SiC by epitaxially growing on 350 μm thick conducting SiC substrates. Electrical characterization and alpha spectral measurements performed on Ni/4H-SiC and Ti/4H-SiC SBDs are reported in this work. The spectral measurements were carried out using 241Am alpha emitting radioactive source. Ni/ 4H-SiC Schottky detector showed a better spectral response with 22.87 keV FWHM (∼ 0.416%) at a reverse bias of 150 V for 5.48 MeV alpha particles while Ti/4H-SiC Schottky detector achieved a resolution of 38.25 keV FWHM (∼ 0.697%) at 170 V reverse bias. This work presented spectral broadening analysis to understand the various factors affecting the energy resolution of the detectors. The extracted charge collection efficiencies (CCEs) are approximately 99% in both the detectors. In addition, polarization effects are not noticed in any of the fabricated detectors. The diffusion length of minority carriers (Lp ) is computed based on the drift-diffusion model by fitting the CCE curve as a function of applied bias, and the values are close to 9 μm and 7 μm for Ni/4H-SiC SBD and Ti/4H-SiC SBD detectors, respectively. Annealing at 400°C for 5 minutes in N2 ambient resulted in resolution of 23.98 keV FWHM (∼ 0.436%) for Ni/4H-SiC SBD detector at -170 V and 36.21 keV FWHM (∼ 0.661%) for Ti/4H-SiC SBD detector at -150 V. Overall Ni/4H-SiC SBD detectors showed superior spectral characteristics and superior resolution when compared to Ti/4H-SiC SBD detectors. However, the Ti/4H-SiC SBD detector fabricated in this work performed better than the previously reported work on a similar device structure. Hence, future work aimed at improving resolution of radiation detectors could also consider Ti/4H-SiC SBDs along with Ni/4H-SiC SBDs.
Style APA, Harvard, Vancouver, ISO itp.
2

Yoneda, S., Tomoaki Furusho, H. Takagi, S. Ohta i Shigehiro Nishino. "Homoepitaxial Growth on 4H-SiC (03-38) Face by Sublimation Close Space Technique". Materials Science Forum 483-485 (maj 2005): 129–32. http://dx.doi.org/10.4028/www.scientific.net/msf.483-485.129.

Pełny tekst źródła
Streszczenie:
For preliminary step toward fabrication of MOSFET using 4H-SiC 8) 3 (03 prepared by sublimation method, epitaxial growth of device quality 4H-SiC on 4H-SiC (0001) 8.0° off substrate was carried out and investigated. Smooth and specular surface of 4H-SiC (0001) plane was obtained by optimum growth condition. And epitaxial growth on 4H-SiC 8) 3 (03 and ) 8 3 (03 substrates were carried out with optimum growth conditions of 4H-SiC (0001). Smooth and specular surface was obtained on 4H-SiC 8) 3 (03 and ) 8 3 (03 plane. Growth rate of epilayers of 4H-SiC (0001), 8) 3 (03 and ) 8 3 (03 face were same. Oxidation rate of 4H-SiC (0001), ) 1 (000 , 8) 3 (03 and ) 8 3 (03 face was investigated. The oxidation rate was different depending on the faces. It was observed that the difference of oxidation rate of 8) 3 (03 and ) 8 3 (03 is mainly due to the difference of polarity similar to the case of reported for (0001) and ) 1 (000 .
Style APA, Harvard, Vancouver, ISO itp.
3

Yang, Guang, Hao Luo, Jiajun Li, Qinqin Shao, Yazhe Wang, Ruzhong Zhu, Xi Zhang i in. "Discrimination of dislocations in 4H-SiC by inclination angles of molten-alkali etched pits". Journal of Semiconductors 43, nr 12 (1.12.2022): 122801. http://dx.doi.org/10.1088/1674-4926/43/12/122801.

Pełny tekst źródła
Streszczenie:
Abstract Discrimination of dislocations is critical to the statistics of dislocation densities in 4H silicon carbide (4H-SiC), which are routinely used to evaluate the quality of 4H-SiC single crystals and homoepitaxial layers. In this work, we show that the inclination angles of the etch pits of molten-alkali etched 4H-SiC can be adopted to discriminate threading screw dislocations (TSDs), threading edge dislocations (TEDs) and basal plane dislocations (BPDs) in 4H-SiC. In n-type 4H-SiC, the inclination angles of the etch pits of TSDs, TEDs and BPDs in molten-alkali etched 4H-SiC are in the ranges of 27°−35°, 8°−15° and 2°−4°, respectively. In semi-insulating 4H-SiC, the inclination angles of the etch pits of TSDs and TEDs are in the ranges of 31°−34° and 21°−24°, respectively. The inclination angles of dislocation-related etch pits are independent of the etching duration, which facilitates the discrimination and statistic of dislocations in 4H-SiC. More significantly, the inclination angle of a threading mixed dislocations (TMDs) is found to consist of characteristic angles of both TEDs and TSDs. This enables to distinguish TMDs from TSDs in 4H-SiC.
Style APA, Harvard, Vancouver, ISO itp.
4

Furusho, Tomoaki, Ryota Kobayashi, Taro Nishiguchi, M. Sasaki, K. Hirai, Toshihiko Hayashi, Hiroyuki Kinoshita i Hiromu Shiomi. "Growth of Micropipe Free Crystals on 4H-SiC {03-38} Seeds". Materials Science Forum 527-529 (październik 2006): 35–38. http://dx.doi.org/10.4028/www.scientific.net/msf.527-529.35.

Pełny tekst źródła
Streszczenie:
Growth of 4H-SiC bulk crystals on 4H-SiC {03-38} seeds was done. 4H-SiC {03-38} is obtained by inclining the c-plane toward <01-10> at a 54.7 degrees angle. Growth on the 4H-SiC {03-38} seed has the potential to achieve high quality crystals without micropipes and stacking faults. Micropipe-free c-plane 4H-SiC wafers were achieved by growth on the 4H-SiC {03-38} seed. A transmission X-ray topograph image of the micropipe free c-plane wafer revealed that there are no macroscopic defects with displacements.
Style APA, Harvard, Vancouver, ISO itp.
5

Alexander, Kazuaki Seki, Shigeta Kozawa, Yuji Yamamoto, Toru Ujihara i Yoshikazu Takeda. "Polytype Stability of 4H-SiC Seed Crystal on Solution Growth". Materials Science Forum 679-680 (marzec 2011): 24–27. http://dx.doi.org/10.4028/www.scientific.net/msf.679-680.24.

Pełny tekst źródła
Streszczenie:
We investigated the polytype transition process from 4H-SiC to 6H-SiC during solution growth from the viewpoint of growth mode. The polarity dependence of the dominant grown polytype was similar to those of the sublimation growth and the CVD growth that 4H-SiC relatively grew stably on the C-face. Moreover, the polytype transition occurred during spiral growth. The 6H-SiC expanded to periphery overgrowing on the 4H-SiC. In contrast, there is no sign that 4H-SiC grew on 6H-SiC.
Style APA, Harvard, Vancouver, ISO itp.
6

Naik, Harsh, i T. Paul Chow. "Comparison of Inversion Electron Transport Properties of (0001) 4H and 6H-SiC MOSFETs". Materials Science Forum 679-680 (marzec 2011): 678–81. http://dx.doi.org/10.4028/www.scientific.net/msf.679-680.678.

Pełny tekst źródła
Streszczenie:
The effect of using two different polytypes, 4H-SiC and 6H-SiC, on the performance of (0001) SiC MOSFETs has been studied. 4H-SiC and 6H-SiC MOSFETs have been fabricated with deposited gate oxides followed by oxidation in dry O2 or NO. Device parameters, particularly field-effect mobility, inversion sheet carrier concentration and Hall mobility have been extracted. We have also compared the mobility-limiting mechanisms of (0001) 4H and 6H-SiC MOSFETs and found that inversion mobility can be further improved in 4H-SiC, but not 6H-SiC.
Style APA, Harvard, Vancouver, ISO itp.
7

Moon, Jeong Hyun, Da Il Eom, Sang Yong No, Ho Keun Song, Jeong Hyuk Yim, Hoon Joo Na, Jae Bin Lee i Hyeong Joon Kim. "Electrical Properties of the La2O3/4H-SiC Interface Prepared by Atomic Layer Deposition Using La(iPrCp)3 and H2O". Materials Science Forum 527-529 (październik 2006): 1083–86. http://dx.doi.org/10.4028/www.scientific.net/msf.527-529.1083.

Pełny tekst źródła
Streszczenie:
The La2O3 and Al2O3/La2O3 layers were grown on 4H-SiC by atomic layer deposition (ALD) method. The electrical properties of La2O3 on 4H-SiC were examined using metal-insulator-semiconductor (MIS) structures of Pt/La2O3(18nm)/4H-SiC and Pt/Al2O3(10nm)/La2O3(5nm)/4H-SiC. For the Pt/La2O3(18nm)/4H-SiC structure, even though the leakage current density was slightly reduced after the rapid thermal annealing at 500 oC, accumulation capacitance was gradually increased with increasing bias voltage due to a high leakage current. On the other hand, since the leakage current in the accumulation regime was decreased for the Pt/Al2O3/La2O3/4H-SiC MIS structure owing to the capped Al2O3 layer, the capacitance was saturated. But the saturation capacitance was strongly dependent on frequency, indicating a leaky interfacial layer formed between the La2O3 and SiC during the fabrication process of Pt/Al2O3(10nm)/ La2O3(5nm)/ 4H-SiC structure.
Style APA, Harvard, Vancouver, ISO itp.
8

Kinoshita, Akimasa, Takasumi Ohyanagi, Tsutomu Yatsuo, Kenji Fukuda, Hajime Okumura i Kazuo Arai. "Fabrication of 1.2kV, 100A, 4H-SiC(0001) and (000-1) Junction Barrier Schottky Diodes with Almost Same Schottky Barrier Height". Materials Science Forum 645-648 (kwiecień 2010): 893–96. http://dx.doi.org/10.4028/www.scientific.net/msf.645-648.893.

Pełny tekst źródła
Streszczenie:
It is known that a Schottky barrier height (b) of metal/C-face 4H-SiC Schottky barrier diode (SBD) differ from b of metal/Si-face 4H-SiC SBD. Furthermore, b of metal/4H-SiC SBD varies with annealing temperature. We fabricate 0.231mm2 SBD with Ti/SiC interface using Si-face and C-face 4H-SiC. These SBDs are annealed at several temperatures after a formation of the Ti/SiC interface. As a result, b of Ti/C-face 4H-SiC interface annealed at 400 oC is nearly equal to b of Ti/Si-face 4H-SiC interface annealed at 500 oC and the n-values of these SBDs are nearly equal to the ideal value (unity). Using that annealing condition, we fabricated 25mm2 junction barrier Schottky (JBS) diodes with Ti/SiC interface on Si-face and C-face 4H-SiC epitaxial substrate. b of Si-face and C-face JBS diodes are 1.26eV and 1.24eV, respectively. The leakage currents for both Si-face and C-face JBS diodes are less than 1mA/cm2. The current of 100A is obtained at the forward bias voltage of 1.95V and 2.16V for the Si-face JBS and the C-face JBS.
Style APA, Harvard, Vancouver, ISO itp.
9

Shao, Shi Qian, Wei Cheng Lien, Ayden Maralani, Jim C. Cheng, Kristen L. Dorsey i Albert P. Pisano. "4H-Silicon Carbide p-n Diode for High Temperature (600 °C) Environment Applications". Materials Science Forum 821-823 (czerwiec 2015): 636–39. http://dx.doi.org/10.4028/www.scientific.net/msf.821-823.636.

Pełny tekst źródła
Streszczenie:
In this work, we demonstrate the stable operation of 4H-silicon carbide (SiC) p-n diodes at temperature up to 600 °C. In-depth study methods of simulation, fabrication and characterization of the 4H-SiC p-n diode are developed. The simulation results indicate that the turn-on voltage of the 4H-SiC p-n diode changes from 2.7 V to 1.45 V as the temperature increases from 17 °C to 600 °C. The turn-on voltages of the fabricated 4H-SiC p-n diode decreases from 2.6 V to 1.3 V when temperature changes from 17 °C to 600 °C. The experimental I-V curves of the 4H-SiC p-n diode from 17 °C to 600 °C agree with the simulation ones. The demonstration of the stable operation of the 4H-SiC p-n diodes at high temperature up to 600 °C brings great potentials for 4H-SiC devices and circuits working in harsh environment electronic and sensing applications.
Style APA, Harvard, Vancouver, ISO itp.
10

Xu, Bei, Changjun Zhu, Xiaomin He, Yuan Zang, Shenghuang Lin, Lianbi Li, Song Feng i Qianqian Lei. "First-Principles Calculations on Atomic and Electronic Properties of Ge/4H-SiC Heterojunction". Advances in Condensed Matter Physics 2018 (2018): 1–9. http://dx.doi.org/10.1155/2018/8010351.

Pełny tekst źródła
Streszczenie:
First-principles calculation is employed to investigate atomic and electronic properties of Ge/SiC heterojunction with different Ge orientations. Based on the density functional theory, the work of adhesion, relaxation energy, density of states, and total charge density are calculated. It is shown that Ge(110)/4H-SiC(0001) heterointerface possesses higher adhesion energy than that of Ge(111)/4H-SiC(0001) interface, and hence Ge/4H-SiC(0001) heterojunction with Ge[110] crystalline orientation exhibits more stable characteristics. The relaxation energy of Ge(110)/4H-SiC(0001) heterojunction interface is lower than that of Ge(111)/4H-SiC(0001) interface, indicating that Ge(110)/4H-SiC(0001) interface is easier to form at relative low temperature. The interfacial bonding is analysed using partial density of states and total charge density distribution, and the results show that the bonding is contributed by the Ge-Si bonding.
Style APA, Harvard, Vancouver, ISO itp.
Więcej źródeł

Rozprawy doktorskie na temat "4H-SiC"

1

Florentín, Matthieu. "Irradiation impact on optimized 4H-SiC MOSFETs". Doctoral thesis, Universitat Politècnica de Catalunya, 2016. http://hdl.handle.net/10803/395187.

Pełny tekst źródła
Streszczenie:
Silicon (Si) power device’ technologies have reached a high maturity level, but current limitations on mechanic, temperature operation and electric performances require to investigate other semiconductor materials that can potentially compete with and overcome those border issues. This is the case of Silicon Carbide (SiC) and Gallium Nitride (GaN) which are becoming serious competitors to the Si due to their superior physical properties. Concerning SiC, the 4Hpolytype seems to be the best suitable candidate for high power MOSFETs according to its band gap, electric field strength, electron bulk mobility, and attainable threshold voltage, among others. But still, technological processes must be optimized in order to SiC MOSFETS can compete with their Si counterparts. This is the case of the gate oxidation process. A reduction of interface charge density is required for threshold voltage stability, and further improvements of the interface quality are also needed for high inversion mobility values. Once solved these problems, a path toward new perspectives of high power applications will be opened. This work is the direct continuation of the Aurore Constant’s work. It is focused on 4HSiC based devices, more specifically on the gate oxidation processes and their behaviour under different harsh environments. Up to now, most of the works carried out were focused on the improvement of the Silicon Dioxide-Silicon Carbide (SiO2/SiC) interface quality. Solving those problems would allow designing high-speed and low-switching losses MOSFETs. In the past work, the main strength was focused on a new surface pre-treatment and on a gate oxidation process. Results showed improved electrical performances. However, we are convinced that better values can be obtained by optimizing the post-oxidation annealing step, by performing surface counter doping or by performing special irradiation treatments. All the efforts of this work will oriented to the development of reliable SiC MOSFETs with improved electrical parameters, which can operate under harsh environments (like high temperature or proton/electron irradiated environment). Thus, the mains guidelines of this Ph. D. Thesis are in accordance with the following lines: 1. State of the art on various SiC related fields. 2. Electrical characterization processes. 3. Proton irradiation impact on 4H-SiC MOSFETs and charge build-up mechanisms theory at the SiO2/SiC interface. 4. Electron irradiation impact on 4H-SiC MOSFETs. 5. Gate oxidation and implantation processes optimization. 6. Robustness limit of the improved processes under irradiation environments.
Las tecnologías de dispositivos de potencia en silicio (Si) han alcanzado una gran madurez. Sin embargo, las limitaciones del Si debidas a sus restricciones mecánicas, térmicas y eléctricas hacen necesario otros materiales semiconductores que puedan competir con el Si y superar sus limitaciones. Este es el caso del Carburo de Silicio (SiC) y del Nitruro de Galio (GaN) que ya comienzan a ser serios competidores del Si debido a sus mejores propiedades físicas. En lo que respecta al SiC, el politipo 4H es el candidato más adecuado para la integración de MOSFETs de potencia debido, entre otros, a los valores del bandgap, campo eléctrico crítico, movilidad volumíca de los electrones y tensión umbral alcanzable. A pesar de estas ventajas teóricas del material, es necesario optimizar cada uno de los procesos tecnológicos involucrados en la fabricación de un MOSFET en SiC para que realmente pueda competir con su contrapartida en Si. Este es el caso del proceso de oxidación para la formación del dieléctrico de puerta. Concretamente, una buena estabilidad de la tensión umbral del componente requiere disminuir la densidad de cargas en la interfase óxido/semiconductor, y mejoras adicionales en la calidad de esta interfase son también necesarias para obtener altos valores de la movilidad de los portadores en el canal de inversión. La solución de los problemas tecnológicos anteriormente enunciados abrirá nuevas perspectivas a las aplicaciones de alta potencia. Este trabajo es una continuación directa del de Aurore Constant. Se centra en dispositivos basados en 4H-SiC, y más específicamente en los procesos de oxidación de puerta, y de sus comportamientos eléctricos en diferente ambientes de trabajo hostiles. Hasta la fecha, la mayor parte de la investigación se ha centrado en la mejora de la calidad de la interfase dióxido de silicio/carburo de silicio (SiO2/SiC). La solución de estos problemas debería permitir el diseño de MOSFETs muy rápidos y con pérdidas de conmutación muy bajas. El objetivo del trabajo previo de Aurore Constant fue encontrar un nuevo procedimiento de limpieza de la superficie antes de realizar la oxidación, y en definir un nuevo proceso de oxidación para la formación del dieléctrico de puerta. Los resultados obtenidos mostraron claras mejoras del comportamiento eléctrico de los componentes. Sin embargo, estamos convencidos que la mejora podría ser aún mayor optimizando la etapa del recocido post-oxidación, utilizando un proceso adicional de dopaje superficial, o realizando un adecuado proceso de irradiación. Todos los esfuerzos de este trabajo se han dirigido al desarrollo de MOSFETs en SiC fiables, con mejores características eléctricas, y capaces de trabajar en ambientes de alta temperatura y de irradiación protónica o electrónica. En resumen, las principales líneas de esta Tesis son las siguientes: 1. Estado del arte de los diferentes dominios de trabajo del SiC. 2. Procesos y técnicas de caracterización eléctrica. 3. Impacto de la irradiación de protones en MOSFETs fabricados en 4H-SiC, y descripción teórica de los mecanismos de creación de carga en la interfase SiO2/SiC. 4. Impacto de la irradiación electrónica en MOSFETs fabricados en 4H-SiC. 5. Optimización de los procesos de oxidación y de implantación. 6. Límite de robustez de los procesos tecnológicos optimizados en ámbitos irradiados.
Style APA, Harvard, Vancouver, ISO itp.
2

Robert, Teddy. "Spectroscopie des fautes d'empilement dans 4H-SiC". Montpellier 2, 2009. http://www.theses.fr/2009MON20166.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
3

Li, Mingyu Williams John R. "Ohmic contacts to implanted (0001) 4H-SiC". Auburn, Ala., 2009. http://hdl.handle.net/10415/1960.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
4

Haasmann, Daniel Erwin. "Active Defects in 4H–SiC MOS Devices". Thesis, Griffith University, 2015. http://hdl.handle.net/10072/367037.

Pełny tekst źródła
Streszczenie:
The research findings presented in this thesis have provided several key contributions towards a better understanding of the SiC–SiO2 interface in SiC MOS structures. The electrically active defects directly responsible for degrading the channel-carrier mobility in 4H–SiC MOSFETs have been identified and a novel technique to detect these defects in 4H–SiC MOS capacitors has been proposed and experimentally demonstrated. With a better understanding of defects at the SiC–SiO2 interface two alternative gate oxide growth processes have been proposed to overcome the practical limitations associated with current NO-nitridation techniques in high-volume, production based oxidation furnaces. This work therefore contributes to the wider research effort towards improving the performance of SiC MOSFETs in several ways. The following paragraphs summarise the key conclusions that have been obtained as a result of this study. Electrically Active Defects and the Channel-Carrier Mobility (Chapter 3) A critical review of defects at the SiC–SiO2 interface exposed a few key discrepancies in both the current understanding of the dominant defects responsible for channel-carrier mobility degradation in 4H–SiC MOSFETs and in the current approach to characterise and evaluate the SiC–SiO2 interface. Firstly, it was recognised that the Shockley-Read-Hall statistical model, based on thermally activated transport for traps spatially located at the semiconductor-oxide interface, cannot be directly applied to describe the transfer mechanism between free conduction band electrons and the shallow NITs near EC. This implication tends to suggest that the NITs near EC in SiC MOS structures cannot be accurately examined using traditional MOS characterisation techniques that are based on this statistical model. Secondly, in accordance with the studies conducted by Saks et. al. [1-3], it was realized that channel-carrier mobility degradation in 4H–SiC MOSFETs is primarily due to the significantly reduced free electron density in the inversion channel. In light of this understanding, the interfacial defects that actively trap channel electrons under strong inversion conditions were considered to be dominant in these devices as opposed to the NITs near EC that are typically examined using conventional MOS characterisation techniques on N-type MOS capacitors in depletion. To further support this hypothesis, a theoretical analysis of the inversion carrier concentration using the charge sheet model was conducted to demonstrate that the NITs with energy levels corresponding to strong inversion are of key importance to the channel-carrier mobility.
Thesis (PhD Doctorate)
Doctor of Philosophy (PhD)
Griffith School of Engineering
Science, Environment, Engineering and Technology
Full Text
Style APA, Harvard, Vancouver, ISO itp.
5

Horita, Masahiro. "Isopolytypic Growth of Nonpolar 4H-AlN on 4H-SiC and Its Device Applications". 京都大学 (Kyoto University), 2009. http://hdl.handle.net/2433/81830.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
6

Sejil, Selsabil. "Optimisation de l'épitaxie VLS du semiconducteur 4H-SiC : Réalisation de dopages localisés dans 4H-SiC par épitaxie VLS et application aux composants de puissance SiC". Thesis, Lyon, 2017. http://www.theses.fr/2017LYSE1170/document.

Pełny tekst źródła
Streszczenie:
L'objectif du projet VELSIC a été de démontrer la faisabilité de jonctions p+/n- profondes dans le semiconducteur 4H-SiC, de haute qualité électrique, comprenant une zone p++ réalisée par un procédé original d'épitaxie localisée à basse température (1100 – 1200°C), en configuration VLS (Vapeur - Liquide - Solide). Cette technique innovante de dopage par épitaxie utilise le substrat de SiC mono cristallin comme un germe de croissance sur lequel un empilement enterré de Al - Si est porté à fusion pour constituer un bain liquide, lequel est alimenté en carbone par la phase gazeuse. Cette méthode se positionne comme une alternative avantageuse à l'implantation ionique, actuellement utilisée par tous les fabricants de composants en SiC, mais qui présente des limitations problématiques encore non résolues à ce jour. Les travaux de thèse ont exploré toutes les facettes du processus complet de fabrication de diodes de test, avec une attention particulière portée sur l'optimisation de la gravure de cuvettes dans le substrat SiC. Le cœur des travaux a été concentré sur l'optimisation de l'épitaxie VLS localisée. L'étude a confirmé la nécessité de limiter la vitesse de croissance vers 1 µm/h pour conserver une bonne cristallinité du matériau épitaxié. Elle a également mis en évidence l'action directe du champ électromagnétique radiofréquence sur la phase liquide, conduisant à une très forte influence du diamètre des cuvettes gravées sur l'épaisseur du SiC déposé. Un remplissage quasiment complet des cuvettes de 1 µm de profondeur à très fort dopage p++ a été démontré. À partir des couches VLS optimisées, des démonstrateurs de types diodes p+/n- ont été fabriqués. Sur les meilleurs échantillons, sans passivation ni protection périphérique, des tensions de seuil en régime direct (entre 2,5 et 3 V) ont, pour la première fois, été mesurées, sans recourir à un recuit haute température après épitaxie. Elles correspondent aux valeurs attendues pour une vraie jonction p-n sur 4H-SiC. Des densités de courant de plusieurs kA/cm2 ont également pu être injectées pour des tensions situées autour de 5 - 6 V. En régime de polarisation inverse, aucun claquage n'est observé jusqu'à 400 V et les densités de courant de fuite à faible champ électrique dans la gamme 10-100 nA/cm2 ont été mesurées. Toutes ces avancées si situent au niveau de l'état de l'art pour des composants SiC aussi simples, toutes techniques de dopage confondues
The objective of the VELSIC project has been to demonstrate the feasibility of 1 µm deep p+/n- junctions with high electrical quality in 4H-SiC semiconductor, in which the p++ zone is implemented by an original low-temperature localized epitaxy process ( 1100 - 1200 °C ), performed in the VLS (Vapor - Liquid - Solid) configuration. This innovative epitaxy doping technique uses the monocrystalline SiC substrate as a crystal growth seed. On the substrate (0001-Si) surface, buried patterns of Al - Si stack are fused to form liquid islands which are fed with carbon by C3H8 in the gas phase. This method is investigated as a possible higher performance alternative to the ion implantation process, currently used by all manufacturers of SiC devices, but which still experiences problematic limitations that are yet unresolved to date. Although the main focus of the study has been set on the optimization of localized VLS epitaxy, our works have explored and optimized all the facets of the complete process of test diodes, from the etching of patterns in the SiC substrate up to the electrical I - V characterization of true pn diodes with ohmic contacts on both sides.Our results have confirmed the need to limit the growth rate down to 1 µm/h to maintain good crystallinity of the epitaxial material. It has also highlighted the direct action of the radiofrequency electromagnetic field on the liquid phase, leading to a very strong influence of the diameter of the etched patterns on the thickness of the deposited SiC. A nearly complete filling of the 1 µm deep trenches with very high p++ doping has been demonstrated. Using optimized VLS growth parameters, p+/n- diode demonstrators have been processed and tested. On the best samples, without passivation or peripheral protection, high direct-current threshold voltages, between 2.5 and 3 V, were measured for the first time without any high-temperature annealing after epitaxy. These threshold voltage values correspond to the expected values for a true p-n junction on 4H-SiC. Current densities of several kA/cm2 have also been injected at voltages around 5 - 6 V. Under reverse bias conditions, no breakdown is observed up to 400 V and low leakage current densities at low electric field, in the range 10 - 100 nA/cm2, have been measured. All these advances align with or exceed state-of-the-art results for such simple SiC devices, obtained using any doping technique
Style APA, Harvard, Vancouver, ISO itp.
7

Usman, Muhammad. "Impact of Ionizing Radiation on 4H-SiC Devices". Doctoral thesis, KTH, Integrerade komponenter och kretsar, 2012. http://urn.kb.se/resolve?urn=urn:nbn:se:kth:diva-60763.

Pełny tekst źródła
Streszczenie:
Electronic components, based on current semiconductor technologies and operating in radiation rich environments, suffer degradation of their performance as a result of radiation exposure. Silicon carbide (SiC) provides an alternate solution as a radiation hard material, because of its wide bandgap and higher atomic displacement energies, for devices intended for radiation environment applications. However, the radiation tolerance and reliability of SiC-based devices needs to be understood by testing devices  under controlled radiation environments. These kinds of studies have been previously performed on diodes and MESFETs, but multilayer devices such as bipolar junction transistors (BJT) have not yet been studied. In this thesis, SiC material, BJTs fabricated from SiC, and various dielectrics for SiC passivation are studied by exposure to high energy ion beams with selected energies and fluences. The studies reveal that the implantation induced crystal damage in SiC material can be partly recovered at relatively low temperatures, for damag elevels much lower than needed for amorphization. The implantation experiments performed on BJTs in the bulk of devices show that the degradation in deviceperformance produced by low dose ion implantations can be recovered at 420 oC, however, higher doses produce more resistant damage. Ion induced damage at the interface of passivation layer and SiC in BJT has also been examined in this thesis. It is found that damaging of the interface by ionizing radiation reduces the current gain as well. However, for this type of damage, annealing at low temperatures further reduces the gain. Silicon dioxide (SiO2) is today the dielectric material most often used for gate dielectric or passivation layers, also for SiC. However, in this thesis several alternate passivation materials are investigated, such as, AlN, Al2O3 and Ta2O5. These materials are deposited by atomic layer deposition (ALD) both as single layers and in stacks, combining several different layers. Al2O3 is further investigated with respect to thermalstability and radiation hardness. It is observed that high temperature treatment of Al2O3 can substantially improve the performance of the dielectric film. A radiation hardness study furthermore reveals that Al2O3 is more resistant to ionizing radiation than currently used SiO2 and it is a suitable candidate for devices in radiation rich applications.
QC 20120117
Style APA, Harvard, Vancouver, ISO itp.
8

Zeng, Yutong. "Tailored Al2O3/4H-SiC interface using ion implantation". Thesis, KTH, Skolan för informations- och kommunikationsteknik (ICT), 2011. http://urn.kb.se/resolve?urn=urn:nbn:se:kth:diva-90233.

Pełny tekst źródła
Streszczenie:
The effects of ion implantation of Al2O3interface to 4H-SiC epitaxial n- and p-type layers are presented. Different fluencies of carbon and nitrogen ions are used, as well as different annealing processes, with the aim to study the effects of implanted ions at the Al2O3/SiC interface. Capacitance-Voltage (C-V) behavior for fabricated MOS capacitors is studied before and after implantation to determine the effect of the implantation. Terman‟s method was employed to extract the density of interface traps (Dit) present at the Al2O3/SiC interface. Effective oxide charges density (Neff), present inside the Al2O3,was also evaluated by comparing the theoretical (ideal) C-V curve with the experimental C-V curves. It is generally known, and also proved by this study, that Al2O3 on n-type 4H-SiC shows significantly higher effective oxide charges density (Neff) and density of interface traps (Dit=3-4×1012 eV-1cm-2) compared to n-type SiO2/SiC MOS capacitors. However, the analysis of the collected data from N and C implanted n-type Al2O3/SiC samples show Dit values around 2-9×1011 eV-1cm-2, i.e., an effective reduction has been achieved by the ion implantation. The values of Neff for N ion implanted n-type Al2O3/SiC is as high as 1013 cm-2 in some cases, but C implanted n-type Al2O3/SiC sample shows exceptionally low Neff =1.8×1011 cm-2, which is comparable to SiO2/SiC based MOS capacitor. This result suggest that using C ion implantation before the formation of the oxide layer could be a promising approach to improving both oxide and interface properties of n-type 4H-SiC MOS capacitors.
Style APA, Harvard, Vancouver, ISO itp.
9

Karalas, Charilaos-Kimonas. "Process optimization for the 4H-SiC/SiO2 interface". Thesis, KTH, Skolan för informations- och kommunikationsteknik (ICT), 2015. http://urn.kb.se/resolve?urn=urn:nbn:se:kth:diva-174842.

Pełny tekst źródła
Streszczenie:
This thesis aims to optimize the process for the 4H-SiC/SiO2 interface formations. The experiments are made on metal-oxide-semiconductor (MOS) structures, where the semiconductor is an n-type epitaxially grown 4H-SiC thin film. The oxide is fabricated either with thermal oxidation, or by using plasma-enhanced chemical vapour deposition (PeCVD), utilising two different tools, Precision 5000 Mark II (P5000) and Plasmalab 80Plus system (Pekka). The deposition temperature is varied for the thermally grown oxide, while power, pressure and gas ratio of N2O/SiH4 is investigated for the PeCVD method. Also the post deposition annealing (PDA) temperature is studied for both techniques. The oxide formation and PDA is done in N2O ambient in order to study the effect of nitrogen passivation of the traps that exist at the interface of 4H-SiC/SiO2. After the dielectric formation the structures are electrically and structurally characterized. The electrical characterization is done by capacitance-voltage (CV) and current-voltage (IV) measurements while the structural characterization is done with atomic force microscopy (AFM). The density of interface traps (Dits) is extracted using the Terman method from CV data. It is observed that the flatband voltage drops almost to zero when the samples are annealed in nitrogen rich ambient, resulting in a more electrically uniform oxide. Also, Dits can also be reduced by nitrogen treatment when the oxide is deposited by the PeCVD technique. However, it appears that the Terman method cannot determine the amount of traps along the entire bandgap and it is clear that a large amount of Dits are still present closer to the conduction band. Finally, it is found that there is a larger spread in the data extracted from the samples deposited by P5000 in comparison to Pekka, indicating that Pekka is a more reliable tool for oxide deposition in SiC substrate.
Style APA, Harvard, Vancouver, ISO itp.
10

Suvanam, Sethu Saveda. "Radiation Hardness of 4H-SiC Devices and Circuits". Doctoral thesis, KTH, Integrerade komponenter och kretsar, 2017. http://urn.kb.se/resolve?urn=urn:nbn:se:kth:diva-199907.

Pełny tekst źródła
Streszczenie:
Advances in space and nuclear technologies are limited by the capabilities of the conventional silicon (Si) electronics. Hence, there is a need to explore materials beyond Si with enhanced properties to operate in extreme environments. In this regards, silicon carbide (4H-SiC), a wide bandgap semiconductor, provides suitable solutions. In this thesis, radiation effects of 4H-SiC bipolar devices, circuits and dielectrics for SiC are investigated under various radiation types. We have demonstrated for the first time the radiation hardness of 4H-SiC logic circuits exposed to extremely high doses (332 Mrad) of gamma radiation and protons. Comparisons with previously available literature show that our 4H-SiC bipolar junction transistor (BJT) is 2 orders of magnitude more tolerant under gamma radiation to existing Si-technology. 4H-SiC devices and circuits irradiated with 3 MeV protons show about one order of magnitude higher tolerance in comparison to Si. Numerical simulations of the device showed that the ionization is most influential in the degradation process by introducing interface states and oxide charges that lower the current gain. Due to the gain reduction of the BJT, the voltage reference of the logic circuit has been affected and this, in turn, degrades the voltage transfer characteristics of the OR-NOR gates. One of the key advantages of 4H-SiC over other wide bandgap materials is the possibility to thermally grow silicon oxide (SiO2) and process device in line with advanced silicon technology. However, there are still questions about the reliability of SiC/SiO2 interface under high power, high temperature and radiation rich environments. In this regard, aluminium oxide (Al2O3), a chemically and thermally stable dielectric, has been investigated. It has been shown that the surface cleaning treatment prior to deposition of a dielectric layer together with the post dielectric annealing has a crucial effect on interface and oxide quality. We have demonstrated a new method to evaluate the interface between dielectric/4H-SiC utilizing an optical free carrier absorption technique to quantitative measure the charge carrier trapping dynamics. The radiation hardness of Al2O3/4H-SiC is demonstrated and the data suggests that Al2O3 is better choice of dielectric for devices in radiation rich applications.

QC 20170119

Style APA, Harvard, Vancouver, ISO itp.
Więcej źródeł

Książki na temat "4H-SiC"

1

Chemical Mechanical Polishing Optimization for 4H-SiC. Storming Media, 2000.

Znajdź pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
2

Electrical and Optical Characterization of Intrinsic and Ion- Implantation Induced Defects in 6H- and 4H-SiC. Storming Media, 1999.

Znajdź pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
3

National Aeronautics and Space Administration (NASA) Staff. Study of Bulk and Elementary Screw Dislocation Assisted Reverse Breakdown in Low-Voltage (Less Than 250 V) 4h-Sic P(+)N Junction Diodes. Part 1; DC Properties. Independently Published, 2018.

Znajdź pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.

Części książek na temat "4H-SiC"

1

Gudjónsson, G., Fredrik Allerstam, Per Åke Nilsson, Hans Hjelmgren, Einar O. Sveinbjörnsson, Herbert Zirath, T. Rödle i R. Jos. "High Frequency 4H-SiC MOSFETs". W Materials Science Forum, 795–98. Stafa: Trans Tech Publications Ltd., 2007. http://dx.doi.org/10.4028/0-87849-442-1.795.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
2

Kalinina, Evgenia, Nikita B. Strokan, Alexandr M. Ivanov, A. Sadohin, A. Azarov, V. Kossov, R. Yafaev i S. Lashaev. "4H-SiC High Temperature Spectrometers". W Materials Science Forum, 941–44. Stafa: Trans Tech Publications Ltd., 2007. http://dx.doi.org/10.4028/0-87849-442-1.941.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
3

Starke, Ulrich, W. Y. Lee, C. Coletti, S. E. Saddow, Robert P. Devaty i W. J. Choyke. "SiC Pore Surfaces: Surface Studies of 4H-SiC(1-102) and 4H-SiC(-110-2)". W Silicon Carbide and Related Materials 2005, 677–80. Stafa: Trans Tech Publications Ltd., 2006. http://dx.doi.org/10.4028/0-87849-425-1.677.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
4

Sveinbjörnsson, Einar O., G. Gudjónsson, Fredrik Allerstam, H. Ö. Ólafsson, Per Åke Nilsson, Herbert Zirath, T. Rödle i R. Jos. "High Channel Mobility 4H-SiC MOSFETs". W Silicon Carbide and Related Materials 2005, 961–66. Stafa: Trans Tech Publications Ltd., 2006. http://dx.doi.org/10.4028/0-87849-425-1.961.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
5

Holmestad, R., JP Morniroli, JM Zuo, JCH Spence i A. Avilov. "Quantitative CBED studies of SiC 4H". W Electron Microscopy and Analysis 1997, 137–40. Boca Raton: CRC Press, 2022. http://dx.doi.org/10.1201/9781003063056-35.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
6

Shishkin, Y., Yue Ke, Fei Yan, Robert P. Devaty, W. J. Choyke i S. E. Saddow. "CVD Epitaxial Growth of 4H-SiC on Porous SiC Substrates". W Silicon Carbide and Related Materials 2005, 255–58. Stafa: Trans Tech Publications Ltd., 2006. http://dx.doi.org/10.4028/0-87849-425-1.255.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
7

Clouter, M. J., Yue Ke, Robert P. Devaty, W. J. Choyke, Y. Shishkin i S. E. Saddow. "Raman Spectra of a 4H-SiC Epitaxial Layer on Porous and Non-Porous 4H-SiC Substrates". W Materials Science Forum, 415–18. Stafa: Trans Tech Publications Ltd., 2007. http://dx.doi.org/10.4028/0-87849-442-1.415.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
8

Noborio, Masato, Jun Suda, Svetlana Beljakowa, Michael Krieger i Tsunenobu Kimoto. "4H-SiC MISFETs with Nitrogen-Containing Insulators". W Silicon Carbide, 235–65. Weinheim, Germany: Wiley-VCH Verlag GmbH & Co. KGaA, 2011. http://dx.doi.org/10.1002/9783527629077.ch10.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
9

Gudjónsson, G., Fredrik Allerstam, H. Ö. Ólafsson, Per Åke Nilsson, Hans Hjelmgren, Kristoffer Andersson, Einar O. Sveinbjörnsson, Herbert Zirath, T. Rödle i R. Jos. "High Power-Density 4H-SiC RF MOSFETs". W Silicon Carbide and Related Materials 2005, 1277–80. Stafa: Trans Tech Publications Ltd., 2006. http://dx.doi.org/10.4028/0-87849-425-1.1277.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
10

Chandrashekhar, M. V. S., Christopher I. Thomas, Hui Li, Michael G. Spencer i Amit Lal. "Demonstration of a 4H SiC Betavoltaic Cell". W Silicon Carbide and Related Materials 2005, 1351–54. Stafa: Trans Tech Publications Ltd., 2006. http://dx.doi.org/10.4028/0-87849-425-1.1351.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.

Streszczenia konferencji na temat "4H-SiC"

1

Wright, N. G. "4H-SiC power TCAD". W IEE Colloquium on New Developments in Power Semiconductor Devices. IEE, 1996. http://dx.doi.org/10.1049/ic:19960863.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
2

O'Neill, A., F. Arith, J. Urresti, K. Vasilevskiy, N. Wright i S. Olsen. "High Mobility 4H-SiC MOSFET". W 2018 14th IEEE International Conference on Solid-State and Integrated Circuit Technology (ICSICT). IEEE, 2018. http://dx.doi.org/10.1109/icsict.2018.8564911.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
3

Chen, G., Z. Y. Li, S. Bai i P. Han. "Properties of homoepitaxial 4H-SiC and characteristics of Ti/4H-SiC Schottky barrier diodes". W Sixth International Conference on Thin Film Physics and Applications. SPIE, 2008. http://dx.doi.org/10.1117/12.792156.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
4

Liu, Xingfang, Jinmin Li, Guosheng Sun, Jin Ning, Yongmei Zhao, Jiaye Li, Muchang Luo i Yiping Zeng. "Visible blind p+/p/n-/n+ UV 4H-SiC photodiodes based on 4H-SiC homoepilayers". W 2006 8th International Conference on Solid-State and Integrated Circuit Technology Proceedings. IEEE, 2006. http://dx.doi.org/10.1109/icsict.2006.306554.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
5

Kosa, A., J. Benkovska, L. Stuchlikova, D. Buc, F. Dubecky i L. Harmatha. "Radiation hardness of 4H-SiC structuresues". W 2014 10th International Conference on Advanced Semiconductor Devices & Microsystems (ASDAM). IEEE, 2014. http://dx.doi.org/10.1109/asdam.2014.6998641.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
6

Umana-Membreno, G. A., J. R. Sharp, A. Choudhary, J. Antoszewski, S. Dhar, S. H. Ryu, A. K. Agarwal i L. Faraone. "Magnetoresistance characterisation of 4H-SiC MOSFETs". W 2012 Conference on Optoelectronic and Microelectronic Materials & Devices (COMMAD). IEEE, 2012. http://dx.doi.org/10.1109/commad.2012.6472423.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
7

Chandrashekhar, MVS, Rajesh Duggirala, Amit Lal i Michael G. Spencer. "4H SiC beta-powered temperature transducer". W 2007 IEEE Sensors. IEEE, 2007. http://dx.doi.org/10.1109/icsens.2007.4388558.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
8

Chen, H., J. H. Mo, L. Li, H. S. Pan, Z. Feng, F. Yang i S. J. Cai. "250W S-band 4H-SiC MESFET". W 2008 Asia Pacific Microwave Conference. IEEE, 2008. http://dx.doi.org/10.1109/apmc.2008.4958052.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
9

Jae Sang Lee, Ji-Hong Kim, Byung-Moo Moon, Wook Bahng, Sang-Cheol Kim, Nam-Kyun Kim i Sang-Mo Koo. "Epitaxial ZnO/4H-SiC heterojunction diodes". W 2010 IEEE 3rd International Nanoelectronics Conference (INEC). IEEE, 2010. http://dx.doi.org/10.1109/inec.2010.5424596.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
10

Yu, Pen-Li, Noah Opondo, Sen Dai, Boyang Jiang, Dallas T. Morisette i Sunil A. Bhave. "Single Crystalline 4H-SiC Membrane Resonators". W 2018 IEEE International Frequency Control Symposium (IFCS). IEEE, 2018. http://dx.doi.org/10.1109/fcs.2018.8597489.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.

Raporty organizacyjne na temat "4H-SiC"

1

Wu, Jian, J. Hu, J. H. Zhao, X. Wang, X. Li i T. Burke. High Mobility 4H-SiC Trenched Gate MOSFETs. Fort Belvoir, VA: Defense Technical Information Center, sierpień 2006. http://dx.doi.org/10.21236/ada507271.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
2

Baliga, Jayant, i Pronita Mehrotra. 4H SiC Lateral Single Zone RESURF Diodes. Fort Belvoir, VA: Defense Technical Information Center, grudzień 1998. http://dx.doi.org/10.21236/ada358231.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
3

Zhang, Jiahui, Petre Alexandrov, Jian H. Zhao i Terry Burke. 1677V, 5.7 mohm.cm2 4H-SiC Bipolar Junction Transistors. Fort Belvoir, VA: Defense Technical Information Center, listopad 2004. http://dx.doi.org/10.21236/ada477420.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
4

Neudeck, Philip G., i Christian Fazi. Positive Temperature Coefficient of Breakdown Voltage in 4H-SiC PN Junction Rectifiers. Fort Belvoir, VA: Defense Technical Information Center, styczeń 1998. http://dx.doi.org/10.21236/ada359099.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
5

Katulka, Gary L. Evaluation of Electrical Resistivity Characteristics of Metalized 4H-SiC for Application to Electric Guns. Fort Belvoir, VA: Defense Technical Information Center, kwiecień 1999. http://dx.doi.org/10.21236/ada362521.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
6

Mitra, Souvick, Mulpuri V. Rao, N. Papanicolaou, K. A. Jones i M. Derenge. Deep-Level Transient Spectroscopy Study on Double Implanted N(+)-p and p(+)-n 4H-SiC Diodes. Fort Belvoir, VA: Defense Technical Information Center, styczeń 2004. http://dx.doi.org/10.21236/ada424908.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
7

Swab, Jeffrey J., James W. McCauley, Brady Butler, Daniel Snoha, Donovan Harris, Andrew A. Wereszczak i Mattison K. Ferber. Knoop Hardness on the (0001) Plane of 4H and 6H SiC Single Crystals Fabricated by Physical Vapor Transport. Fort Belvoir, VA: Defense Technical Information Center, maj 2014. http://dx.doi.org/10.21236/ada600386.

Pełny tekst źródła
Style APA, Harvard, Vancouver, ISO itp.
Możesz być także zainteresowany rozszerzonymi bibliografiami na temat „4H-SiC” dla poszczególnych typów źródeł:
Artykuły w czasopismach Rozprawy doktorskie
Oferujemy zniżki na wszystkie plany premium dla autorów, których prace zostały uwzględnione w tematycznych zestawieniach literatury. Skontaktuj się z nami, aby uzyskać unikalny kod promocyjny!

Do bibliografii