Segui questo link per vedere altri tipi di pubblicazioni sul tema: Lumber.
Articoli di riviste sul tema "Lumber"
Cita una fonte nei formati APA, MLA, Chicago, Harvard e in molti altri stili
Vedi i top-50 articoli di riviste per l'attività di ricerca sul tema "Lumber".
Accanto a ogni fonte nell'elenco di riferimenti c'è un pulsante "Aggiungi alla bibliografia". Premilo e genereremo automaticamente la citazione bibliografica dell'opera scelta nello stile citazionale di cui hai bisogno: APA, MLA, Harvard, Chicago, Vancouver ecc.
Puoi anche scaricare il testo completo della pubblicazione scientifica nel formato .pdf e leggere online l'abstract (il sommario) dell'opera se è presente nei metadati.
Vedi gli articoli di riviste di molte aree scientifiche e compila una bibliografia corretta.
1
Onat, Saadettin Murat, and Serkan Özdemir. "Optimizacija parametara proizvodnje ugušćene lamelirane furnirske građe proizvedene upotrebom urea-formaldehidne smole." Drvna industrija 74, no. 3 (September 29, 2023): 327–35. http://dx.doi.org/10.5552/drvind.2023.0079.
Testo completoAbstract (sommario):
This research aims to optimize densified laminated veneer lumber production parameters of compression ratio, press temperature, press time, and adhesive spread rate to maximize their mechanical properties. In the manufacturing process of densified laminated veneer lumber, I-77/51 American poplar clone (Populus deltoides) veneers and urea formaldehyde adhesive are used. The results showed that the compression rate and press time had the most significant impact on the mechanical properties of densified laminated veneer lumber. The optimal production conditions were determined as follows: 38 % compression, press temperature of 170 °C, press time of (10±3) minutes, and spread rate of 150 g/m2. Modulus of rupture, modulus of elasticity, tensile shear strength, and tensile strength perpendicular to panels surface of densified laminated veneer lumbers produced under these conditions increased by 49 %, 8 %, 71 %, and 23 %, respectively, compared to the control group of laminated veneer lumber. So, it can be said that the production parameters of densified laminated veneer lumbers can be optimized safely and effectively using Taguchi method-based grey relational analysis.
2
Rawat, Yashwant Singh, Misganu Eba, and Moti Nebiyu. "Lumber Recovery Rate of Cupressus lusitanica in Arsi Forest Enterprise, Ethiopia." Sustainability 15, no. 2 (January 6, 2023): 1046. http://dx.doi.org/10.3390/su15021046.
Testo completoAbstract (sommario):
In Ethiopia, sawmills have poor capacity utilization primarily due to the outdated equipment that resulted in a low recovery rate and the production of a high amount of wastage. The lumber recovery rate is the output (lumber) of a log in the sawing process. In Ethiopia, Cupressus lusitanica is significantly used for lumber, for furniture production, construction, poles and posts. Sampled logs were processed according to the normal production rate and standard lumber dimension of the sawmill for the purpose of estimating the lumber recovery rate. The present study aimed to investigate the lumber recovery rate of C. lusitanica and the factors affecting it. A total of 26.93 m3 of lumber was produced by the sawmilling operation, representing 72.86% of the overall lumber recovery rate. Furthermore, the sawdust and slabs were recorded as 2.92 m3 (7.90%) of sawdust and 7.11 m3 (19.24%) of slabs, respectively. There were a number of factors that decreased the magnitude of the lumber recovery rate. It was observed that cutting using a wider saw kerf caused a reduction in the rate of lumber recovery owing to the generation of an increased quantity of sawdust. The lumbers were air-seasoned in the sawmill yard. Maximizing the volume of the lumber recovered from the logs can increase the sawmill profitability, lessen the effects of climate change, ensure the sustainable use of natural resources, enhance the energy efficiency and manage wood waste (e.g., recycling and prevention) for green economic development and industrial transformation. This species has a great demand in the wood industry of Ethiopia; hence, the plantation and yield of C. lusitanica must be expanded in order to provide sustainable forestry, protect valuable forest resources and safeguard the biodiversity in the country.
3
Shibasaki, Yasuhiko, Kenta Kobayashi, Tatsuya Suwabe, Kyoko Fuse, Miwako Narita, Hirohito Sone, and Masayoshi Masuko. "Depletion of Pre-Transplant Skeletal Muscle Is a Significant Poor Prognostic Factor in Allogeneic Hematopoietic Cell Transplantation." Blood 134, Supplement_1 (November 13, 2019): 3322. http://dx.doi.org/10.1182/blood-2019-124733.
Testo completoAbstract (sommario):
Introduction Depletion of skeletal muscle is a poor prognostic factor for patients with various malignancies; however its significance for allogeneic hematopoietic cell transplantation (allo-HCT) in patients with hematological disease is unclear. Generally, muscle mass is measured by the methods established by the European Working Group on Sarcopenia in Older People, which require the use of dual energy X-ray absorptiometry or bioimpedance analysis, methods that are not performed in routine practice. Therefore, cross-sectional imaging using computed tomography (CT) has been suggested as an alternative method for analyzing muscle mass in clinical practice. Especially, lumbar total muscle cross-sectional area using CT, normalized for body height, which was named lumbar skeletal muscle mass index (SMI), is reported as an indicator of nutritional status, sarcopenia and cancer cachexia in patients with solid organ malignancy. Aims To clarify the usefulness of a pre-transplant lumber SMI as a prognostic indicator for allo-HCT patients. Methods Among 208 patients with hematological disease who underwent allo-HCT between 2006 and 2017 at our facility, 191 patients (95 males and 96 females) underwent CT scans for routine pre-transplant status assessment. Ninety patients had acute myeloid leukemia, 38 patients had acute lymphoblastic leukemia, 24 patients had myelodysplastic syndrome, 20 patients had malignant lymphoma, and 19 patients had other diseases. The median age of the patients was 42 years old (range: 16-66 years). Seventy-eight patients received myeloablative conditioning and the others received reduced intensity conditioning regimens. The number of patients in each HCT-comorbidity index (HCT-CI) risk group was as follows: low: 72, intermediate: 54 and high: 65. Axial images at the iliac crest were selected for analysis of lumber total muscle cross-sectional area (cm2). The rectus abdominus, psoas and paraspinal muscles were identified and quantified. Lumbar total muscle cross-sectional area was normalized for body height in meters squared (m2) and used to calculate lumbar SMI (cm2/m2). This study was performed in accordance with the Japanese Ethical Guidelines for Medical and Health Research Involving Humans and approved by the Ethical Committee of our facility. Results The median pre-transplant lumber SMI of the male patients was significantly higher than that of the female patients (42.7 (24.9-60.2) mm2/m2 vs. 31.9 (20.7-44.6) mm2/m2, p<0.01). We defined the cutoff value of lumber SMI as 42.7cm2/m2 for male and 31.9cm2/m2 for female patients. In the Kaplan-Meier estimate analysis, low lumber SMI was a significant poor prognostic factor for overall survival (p=0.016). In multivariate analysis using Cox regression model, adjusting for age, refined disease risk index, conditioning and HCT-CI, low lumber SMI was extracted as a significant poor prognostic factor for overall survival (hazard ratio 1.56, 95% confidence interval (CI) 1.03-2.36, p=0.036). By logistic regression analysis, adjusted odds ratio of 1-year non-relapse mortality for low lumber SMI was 2.47 (95% CI 1.13-5.41, p=0.024). Conclusion Low pre-transplant lumber SMI is a significant poor prognostic factor in allo-HCT, independent of other risk factors including HCT-CI and refined disease risk index in patients with hematological disease. It is affected by the high rate of non-relapse mortality in the early phase following allo-HCT in patients with low lumber SMI. Disclosures No relevant conflicts of interest to declare.
4
Song, Shi Quan, Hua Dong Xu, and Li Hai Wang. "The Application of Modal Analysis in Hole-Defect in Lumber." Key Engineering Materials 467-469 (February 2011): 1776–80. http://dx.doi.org/10.4028/www.scientific.net/kem.467-469.1776.
Testo completoAbstract (sommario):
Larch lumbers were tested by using modal analysis technology and Frequency response functions (FRF) were derived. Modal parameters, including first 4 intrinsic frequency and first 3 modal shape, were distinguished by single modal method. Research shows that the intrinsic frequency of hole-defect lumbers is little lower than standard lumbers’ and the change rate of frequency is becoming larger gradually with the diameter of hole-defect. However, it can not judge the position of the hole-defect by the change rate of frequency. The modal shape of the node near the hole-defect always jumps abruptly, so it can estimate the particular position of hole-defect in the lumber. The variation of modal shape is becoming larger gradually with the diameter of hole-defect. It can make qualitative and quantitative estimate to the hole-defect in the lumber by considering intrinsic frequency and modal shape together.
5
Y, Chudasma Hardik, Yadav C. R, and Pareek Pooja. "Management of Katishool by Shaman aushadhi along with Panchkarma therapy A case study." International Journal of Ayurvedic Medicine 10, no. 1 (April 3, 2019): 118–21. http://dx.doi.org/10.47552/ijam.v10i1.1158.
Testo completoAbstract (sommario):
Spondylosis refers to degenerative changes in the spine such as bone spurs and degenerative changes in intervertebral disc. Lumber spondylosis mainly affects on lower spine. In this condition spine is compromised by a narrowing of the space between the vertebrae. In a classic case of lumber spondylosis, the space between discs in the lumbar spine becomes narrowed. Because of this the patient develops numbness, tingling and pain which seem to radiate out from the area. These symptoms are the results of pressure on the nerves as they exit the spinal cord. It has been estimated that about 80% of world population develop lumber spondylosis after the age of 40 years. In Ayurveda, It can compare with a disease Katishool, characterized by Kati pradeshevedana, Kati shunyata, kriya hani, Hasta-pada suptata.in this article we are focusing in the management of Lumber spondolosis (Katishool) through Ayurveda. A 46 year old male patient reported to the outdoor department of Sharir Kriya NIA, Jaipur, with the complains of Kati pradeshevedana (Pain in Lumber region), Kati shunyata (Numbness), Dourbalyata (Weakness), Shramahani (Lethargy) for last 6 month and other associate complaints were Hypertension, debility, lethargy, excessive sleep, burning micturation for four month. The patient was diagnosed as Lumber spondylosis. A combination of Yogaraj Guggulu (2 Tab), Punarnavadi Guggulu (2 Tab) twice a day, along with Dashmoolkwath (40 ml), Capsule Sandhika (1 tab), Grokart Ds (2 Tab), Chropexae (1 Tab) twice a day with water after meal for one months. Patient is treated with some panchkarma procedure like katibasti and karma basti. After one month of treatment a significant response was found.
6
Chang, Wei-Yew, and Chris Gaston. "The competitiveness of Canadian softwood lumber: a disaggregated trade-flow analysis." Canadian Journal of Forest Research 44, no. 12 (December 2014): 1494–506. http://dx.doi.org/10.1139/cjfr-2014-0058.
Testo completoAbstract (sommario):
A recursive dynamic spatial equilibrium model is used to examine the global competitiveness of Canadian softwood lumber. To address the restrictive assumption of softwood lumber homogeneity, this study disaggregates softwood lumber into two product groups: (i) higher grade lumber that includes appearance, select structural-grade lumber, and Japanese J-grade lumber; and (ii) lower grade lumber that includes the United States dimension lumber that is commonly used in construction and utility- and economy-grade lumber. Factors that may affect global softwood lumber markets are simulated in the model to project global softwood lumber trade flows from 2012 to 2021. The results indicate that the reduced lumber supply in western Canada caused by the mountain pine beetle (Dendroctonus ponderosae Hopkins) infestation combined with demand increases in several regions of the world will contribute to a global increase in softwood lumber prices. Our results suggest that the global price increase will be greater for lower grade softwood lumber than for higher grade lumber. The United States and China will continue to be the top two markets for lower grade Canadian softwood lumber. Although Canadian exports of lower grade softwood lumber to the United States are expected to increase marginally over time in response to the recovery of American housing starts, softwood lumber exports to China are expected to drop significantly, and it is forecasted that exports from the Russian Federation will fill that void. These findings provide strong market signals for both forest managers and the forest-products industry to assess supply chain profitability and adjust production planning accordingly.
7
Ziad, Alishbah, Madiha Saeed Wahla, Nimra Riaz, Salma Gul, Muhammad Mahad Umar Lodhi, and Suraya Bano. "OSTEOPOROSIS WITHIN A COHORT OF POSTMENOPAUSAL PAKISTANI WOMEN USING DUAL X-RAY BONE DENSITOMETRY." KHYBER MEDICAL UNIVERSITY JOURNAL 14, no. 4 (December 31, 2021): 193–6. http://dx.doi.org/10.35845/kmuj.2021.21685.
Testo completoAbstract (sommario):
OBJECTIVE: To explore the prevalence of osteopenia and osteoporosis within a cohort of Pakistani postmenopausal women with respect to the lumbar spine and hip.
 METHODS: This cross-sectional study was conducted at Shifa International Hospital Islamabad, Pakistan from September 2019 to Feb 2020. Study comprised of 237 postmenopausal females who visited the outpatient department of the hospital. The T-scores of Bone Mineral density (BMD) data was collected and arranged in three groups: normal, osteopenia and osteoporosis. Data was analyzed to explore the distribution of the data and correlation analyses using R software version 3.6.3.
 RESULTS: Out of 237 females, majority were ranging in age from 61-70 years (n=110; 46.4%), followed by 51-60 years age group (n=60; 25.3%). Osteopenia was noted in 98 (41.4%) cases in lumber spine and hip area. Osteoporosis was found in 79 (33.3%) and 59 (24.9%) cases in lumber spine and hip region respectively. Mean T score was -1.775±-2.000 and median T score was -1.469 for lumber spine and hip. T-scores distribution of lumbar spine and hip indicated the highest proportion having a sore of -2 SD (n=60; 25.3% each), followed by -3 SD in 52 (21.9%) cases. Bone mass density was negatively correlated with age (p≤0.01). However, no significant difference was found among the BMD values of lumbar spine and hip region.
 CONCLUSION: Decreased bone density was a common occurrence affecting postmenopausal females and there is increase in degenerative bone loss with increasing age. Hip and lumbar spine region are equally affected by degenerative bone loss.
8
Murtopo, Ali, Ria Miftakhul Jannah, Sabilla Sabilla, and Labibah Tsaniyah. "Failure Analysis of Glulam Lumber Beam Made from Meranti Lumber Pieces (Shorea SP)." Jurnal Teknik Sipil dan Perencanaan 22, no. 2 (October 24, 2020): 137–45. http://dx.doi.org/10.15294/jtsp.v22i2.26231.
Testo completoAbstract (sommario):
The development of glue-laminated (glulam) lumber beam gives many good results. Meranti (Shorea SP) is one of the construction lumber that can be used as glulam to optimize its use. The limitation of the glulam lumber beam is the limited length of the lumber, so it must be joined to get a certain length. The lumber available in the market on average has a limited size and cross-sectional length. The larger the cross-sectional size and length of the lumber make the higher the price. Used lumber and residual lumber also have many weaknesses, such as the length of suitable lumber is too short, lumber defects, and lumber damages. Further research needs to be done to optimize the use of new, used, and residual meranti lumber through the use of lumber pieces as a glulam lumber beam maker. Standard specimen and test based on ASTM D-198. Glulam lumber beam is made from pieces of meranti lumber planks of certain length which are arranged into lamina beam with the size of 5.5x9.5x150 cm3. Variations in the length of the pieces of meranti lumber planks for making glulam lumber beam, among others, 40 cm, 50 cm, 60 cm, 50 cm with full length lowest layer and 150 cm (full length). The adhesive used is polyurethane glue. The span between supports is 130 cm. The beam is tested for center point loading. The analysis results show that the joints on the outermost layer that receive tensile stress of the glulam lumber beam can cause weakening in the beam because the tensile strength of the adhesive is weaker than the tensile strength of lumber. Failure at the tensile joint of the outer layer of the beam can trigger a shear failure mode. Design of joints should not be placed on layers that are subject to tensile stresses so as not to trigger shear failure modes so that the strength of the glulam lumber beam can be optimal.
9
Reddy, Vijay S., and Robert J. Bush. "Measuring Softwood Lumber Value: A Conjoint Analysis Approach." Forest Science 44, no. 1 (February 1, 1998): 145–57. http://dx.doi.org/10.1093/forestscience/44.1.145.
Testo completoAbstract (sommario):
Abstract Conjoint analysis was used to determine softwood lumber value perceptions among buyers of wood for preservative treatment and to determine trade-offs between lumber attributes and price. Utility functions for each lumber attribute and a model to estimate overall lumber value were developed. Wane was found to be the most important attribute in the evaluation of lumber value, followed by price, accuracy of grading, damage to the lumber package, lumber straightness, and lumber moisture content (in that order). Utility scores of individual respondents and simulation techniques were used to quantify trade-offs between quality and price. Buyers of softwood lumber for preservative treatment were found to be willing to pay a higher price to obtain wane-free lumber. The results of the study provide guidelines for softwood lumber suppliers seeking to differentiate their product while maximizing customer-perceived product value. For. Sci. 44(1):145-157.
10
Khademibami, Laya, Alan Sherrington, Rubin Shmulsky, and Franklin Quin. "Determination of Flexural Strength of Structural Red and White Oak and Hardwood Composite Lumber." Forest Products Journal 71, no. 4 (October 1, 2021): 401–6. http://dx.doi.org/10.13073/fpj-d-21-00051.
Testo completoAbstract (sommario):
Abstract In this research, flexural properties of mill-run, in-grade red and white oak lumber from a single mill and commercially available laminated hardwood composite were evaluated. Structurally graded green (wet) freshly sawn red and white oak 5 by 10-cm (2 by 4-in) nominal lumber as well as glue-laminated hardwood composite billets were tested in bending and their modulus of rupture (MOR) and modulus of elasticity (MOE) properties were developed. It is well documented that MOR and MOE are two major indicators to evaluate flexural strength of wood lumbers. From these data, summary statistics, design values, and mean separations were calculated and reported. Overall, the red and white oak lumber performed similarly to structural No. 2 grade material. The hardwood composite billets were highly uniform. Each of the three materials demonstrated a reasonably good relationship between MOE and MOR, thereby suggesting that MOE could be used as a selection criterion for strength in a commercial use situation.
11
Mottet, Marie-Josée, Gaëtan Daoust, and S. Y. Zhang. "Impact du charançon du pin blanc (Pissodes strobi Peck) dans les plantations dépinette de Norvège (Picea abies (L.) Karst.). Partie 2 : Propriétés du bois des sciages." Forestry Chronicle 82, no. 5 (September 1, 2006): 712–22. http://dx.doi.org/10.5558/tfc82712-5.
Testo completoAbstract (sommario):
We studied the lumber characteristics of 148 trees taken for that purpose during commercial thinning operations in three Norway spruce (Picea abies [L.] Karst.) plantations, aged from 32 to 34 years, which had been attacked by the white pine weevil (Pissodes strobi [Peck]). The trees, with diameters ranging from 14 to 23 cm, were grouped into three quality classes according to the number of major deformations caused by the weevil. The effects of the deformations on rigidity, bending strength, wood density and lumber defects were examined. Results show that in general the deformations caused by the weevil do not affect the lumber properties of Norway spruce on sites of medium- to high-quality. For the three Norway spruce plantations, the mean values of the modulus of elasticity (MOE) of the lumber vary from 8510 to 9357 MPa, and for the modulus of rupture (MOR) range from 36.0 to 42.5 MPa, whereas wood density varies from 324 to 343 kg·m-3. For comparison purposes, the same measurements were taken on lumber from 38 trees in a white spruce (P. glauca [Moench] Voss) plantation that was unaffected by the weevil, but otherwise comparable to the Norway spruce plantation on one of the sites studied. The lumber properties from the Norway spruce taken from deformed or undeformed stems are 34% superior to the white spruce for the MOE, 20% for the MOR and 8% for wood density. The smaller knots in the Norway spruce could explain this difference. On the other hand, a visual classification of this type of wood reveals few differences in the lumber's bending strength or rigidity. Key words: Norway spruce, Picea abies, wood characteristics, MOE, MOR, wood density, lumber, white pine weevil, Pissodes strobi, white spruce, Picea glauca
12
GÖRGÜLÜ, Yasin Furkan, and Murat AYDIN. "Computational Fluid Dynamics and Thermal Analysis of an Unloaded Lumber-drying Kiln." Kastamonu University Journal of Forestry Faculty 23, no. 1 (March 24, 2023): 64–74. http://dx.doi.org/10.17475/kastorman.1269521.
Testo completoAbstract (sommario):
Aim of study: Drying in kilns becomes one of the most significant procedures for the optimal use of wood products since the dimensions alter with changes in relative humidity. Computational fluid dynamics analysis of an unloaded lumber-drying kiln and positioning of the timber to be dried were aimed. Material and methods: The heat and flow analysis of the lumber-drying kiln was analyzed using ANSYS software. Concrete and aluminum were chosen as the floor and wall materials, respectively. The wall thickness was taken as 1 meter. Gravity forces were also taken into account in the study, the number of elements of the created mesh is 87057 and the number of nodes is 17730. Main results: The flow characteristics and temperature analyses formed in the study shed light on the lumber-drying kilns planned to be built. Preliminary information is provided about the positioning of the lumbers to be dried according to flow paths and temperature distributions. Highlights: Flow analyzes of the unloaded lumber-drying kiln were undertaken and streamlines were shown. The thermal analysis of the hot air directed from the fans together with the concrete floor of the drying kiln and the walls made of aluminum panels was made.
13
Samreen, Sana, Mahnaz Hakeem, Hafsa Zaheer, Ambreen Raza, and Abdul Gaffar Billoo. "Factors Associated with Parental Refusal for Lumber Puncture Among Children and Adolescent: A Cross Sectional Survey at a Tertiary Care Hospital." Pakistan Journal of Medical & Health Sciences 16, no. 10 (October 30, 2022): 442–44. http://dx.doi.org/10.53350/pjmhs221610442.
Testo completoAbstract (sommario):
Introduction: The lumbar puncture is frequently used in medical facilities to collect data on the cerebrospinal fluid (CSF). The method aids in the diagnosis of conditions affecting the spine and brain's central nervous system. However, in routine practice out of the many challenges posed by the parents due to lack of education, denial of consent for this procedure is a great challenge at clinical settings. Objectives: To determine the association of various factors with parental refusal for lumbar puncture among pediatric population (age from 1 moth to 18 years). Materials and Methods: A descriptive, cross-sectional study was carried out at the department of pediatrics and child health and department of Emergency at Aga Khan University Hospital, Karachi from June 2017 to May 2018. A total of 178 children 1 month to 18 years old admitted with febrile fits, suspected meningitis or encephalitis who were advised for lumber puncture were included. Results: In the present study, the age of the patients ranged from 1 month to 18 year. Majority of the patients 153 (85.39%) were between 1 month to 6 years of age. There were 115 (64.61%) male patients.. Fever and fits was the most frequent indication (n=151, 84.83%) for lumber puncture in the study. Most of the parents were educated, 68.54% of mothers and 65.17% fathers had graduate level of education, and parents of 47 (26.4%) patients refused for lumber puncture. Conclusion: This study concluded that frequency of parental refusal for lumbar puncture was 26.4% and the most common reason for refusal was fear of complications. Keywords: lumbar puncture, febrile seizures, parental refusal.
14
Adhikari, Sailesh, Brian Bond, and Henry Quesada. "Producing structural grade hardwood lumber as a raw material for cross-laminated timber: Yield and economic analysis." BioResources 19, no. 1 (November 3, 2023): 23–40. http://dx.doi.org/10.15376/biores.19.1.23-40.
Testo completoAbstract (sommario):
The economic feasibility of producing structural-grade hardwood lumber (SGHL) that qualifies as a raw material for structurally rated cross-laminated timber (CLT) was examined. 126 yellow poplar logs from diameters 12 to 15 inches were selected and divided into test and control samples. A log yield study was then conducted of the yield and revenue generated when producing lumber graded with National Hardwood Lumber Association (NHLA) rules, SGHL rules, and a mix of both rules (NHLA and SGHL-graded lumber). Producing mix-grade lumber added approximately 27% more revenue than producing NHLA-grade lumber on average if sawmills adopt a cant sawing method. Mix-grade lumber production resulted in 32% of the total volume produced as SGHL and the remaining 68% as NHLA lumber. As a result, 2 Common and lower-grade lumber board footage was reduced to only 29% in test samples and remained converted into SGHL compared to more than 85% of 2 Common and lower-grade lumber boards for control samples. 95% of the SGHL produced as mixed-graded lumber with NHLA-grade lumber met the specifications required to produce structural CLT, and the remaining 5% can be utilized to produce non-structural grade CLTs if they meet the minimum requirement of the materials for CLT production.
15
Naka, Kozma, Brigitte A. Parsons, and A. L. (Tom) Hammett. "Hardwood lumber industry in the Appalachian region: Focus on exports." Forestry Chronicle 85, no. 1 (January 1, 2009): 75–81. http://dx.doi.org/10.5558/tfc85075-1.
Testo completoAbstract (sommario):
Exports can provide income, employment, and risk diversification. However, the decision to enter the export market requires commitment of sufficient managerial, economic and financial resources. A survey of 214 hardwood lumber mills across 10 states in the Appalachian region was conducted to assess motivation and differences between hardwood lumber exporters and non-exporters. The study examined marketing strategies, business practices, manufacturing equipment used, and exporting process. Business size was the most important criterion to determine the likelihood of export. Hardwood lumber exporters invested more money in equipment, manufactured larger amounts of higher quality lumber, and utilized more species that capture greater value in the marketplace. The findings of this study will help the Appalachian forest industry and government agencies to identify strategies that lead to export opportunities for hardwood lumber. Key words: lumber, lumber industry, lumber export, hardwood lumber, Appalachian region
16
Zafar, Khadija, Narjis Batool, Abid Ali, Nosheen Arshad, Waqar Mahmood Dar, and Adrash Naeem. "Frequency of Lumber Disc Degenerative Diseases in Patients with and Without Radiculopathy and Low Back Pain Using Magnetic Resonance Imaging." Pakistan BioMedical Journal 5, no. 1 (January 31, 2022): 261–65. http://dx.doi.org/10.54393/pbmj.v5i1.279.
Testo completoAbstract (sommario):
Degenerative lumbar disc disease is a condition in which an intervertebral disk and surrounding spinal components are weakened. This might be due to age or a pathogenic cause. Individuals may complain of low back pain. Objective: To determine the pattern of lumbar spine and disc degenerative diseases amongst patients having or not having Low Back Pain with or without radiculopathy diagnosed on Magnetic Resonance Imaging. Methods: Data was collected following inclusion criteria using convenient sampling technique. A total of 266 Patients undergone Lumber MRI scans on MRI Machine 1.5T Phillips. Data was collected from Radiology Department of Tertiary Care Hospital in Lahore, Pakistan. Data was entered and analyzed on SPSS version 20. Age Groups, Gender frequencies were mentioned. Cross Tabulation of Lumber Disc Degenerative Diseases with age and Gender was done and Chi square was applied. P-value ≤0.05 was considered significant. Results: The most prevalent age group for disc degeneration was 40-59 having 56.8 %. Females with disc degeneration have the highest frequency of 143 (53.8%) while males were 123 (48.2%). Lumber Disc degeneration was 101 (38%), Disc Herniation 54 (20.3%), and last with lowest presence of Spinal Canal Stenosis 18 (6.8%). Patients with Radiculopathy with Low back Pain was 61 (22.93%) and only LBP was the most common between the patients having 205 (77.1%). Cross Tabulation of Age Groups with Lumber Disc Pathologies was Significant having P value 0.05. Conclusion: In conclusion MRI can detect Disc Degeneration, Disc Herniation & Buldges, and Spinal Canal Stenosis & Nerve Root Compression. It can be considered significant and accurate to avoid any other interventional procedures. It is also concluded the LBP is an important factor in Disc Degenerative changes & radiculopathy is less seen.
17
AHMAD, MUMTAZ, and MUHAMMAD YASIN. "LUMBER DISCITIS." Professional Medical Journal 17, no. 04 (December 10, 2010): 628–32. http://dx.doi.org/10.29309/tpmj/2010.17.04.3011.
Testo completoAbstract (sommario):
Objectives: To study the occurrence of discitis after lumber disc surgery and its management. Study Design: Observational study. Setting: Department of Neurosurgery QAMC/ BVH Bahawalpur. Period: April 2006 to May 2009. Patients and Methods: This study includes 400 patients who underwent standard laminectomy procedure for disc excision. Patients presenting with backache and leg pain were thoroughly investigated. For the confirmation of herniated disc MRI or lumber route myelography were performed. All patients underwent either fenestration, hemilaminectomy or complete laminectomy for disc excision. Patients were followed for two weeks to three years after surgery. The diagnosis of discitis was on clinical grounds but this condition was confirmed by heamatological examination i.e. ESR, complete blood count, C-reactive protein and radiological examination i.e. MRI, CT and plain X-rays. Results: Eighteen (4.5%) patients out of four hundred patients developed disitis after surgery. Initially all patients were managed conservatively i-e. with complete bed rest and antibiotics .Fifteen (83.33%) patients responded well to this treatment but three (16.67%) patients did not improve and were subjected to surgery. Conclusions: Discitis after lumber disc surgery is rare. Discitis should be considered in any patient who develops severe backache,leg pain and muscles spasms after one to four weeks of lumber disc surgery especially accompanied with fever , raised ESR and elevated C-reactive proteins..A definitive diagnosis is essential for appropriate therapy of discitis.
18
Laurel Oldach. "Lumber sleuths." C&EN Global Enterprise 101, no. 7 (February 27, 2023): 24–29. http://dx.doi.org/10.1021/cen-10107-cover.
Testo completo
19
Farouk, Khalid. "Ureteral Injury during Lumbar Laminectomy: A rare occurrence." Isra Medical Journal 14, no. 1 (March 30, 2022): 36–39. http://dx.doi.org/10.55282/imj.cr92.
Testo completoAbstract (sommario):
During spinal surgery injury to ureters is a rare complication with only few cases has been reported in literature. We come across a case of un-recognized iatrogenic during lumbar laminectomy. The injury went unrecognized initially and was discovered fifteen days later when the patient presented in surgery ER with atypical symptoms of severe right iliac fossa and flank pain. The symptoms were not attributable to any disease pertaining to the respective specialty. In this case report we have highlighted a rare complication which encountered during lumber spine laminectomy, with literature review to give comprehensive information’s to the surgeons and patients regarding this complication and its management approaches. Keywords: Ureter, Injury, Lumber laminectomy, Clinical presentation, Diagnosis, Management
20
Huang, Zhi Wei, and Ming Jie Guan. "Selected Physical and Mechanical Properties of 2-Ply Bamboo Laminated Lumber with Modified Phenol Formaldehyde." Advanced Materials Research 1088 (February 2015): 583–86. http://dx.doi.org/10.4028/www.scientific.net/amr.1088.583.
Testo completoAbstract (sommario):
In this paper, environmental friendly phenol formaldehyde modified with larch thanaka and urea was used to make 2-ply bamboo laminated lumber. Effects of two assemble patterns (inner to inner and outer to outer) on physical and mechanical properties of 2-ply bamboo laminated lumber from carbonized and bleached bamboo strips were investigated. The results showed that modulus of elasticity (MOE) and modulus of rupture (MOR) of carbonized bamboo laminated lumber were better than that of bleached bamboo laminate lumber. It illustrated that physical and mechanical properties of carbonized bamboo laminated lumber became better. The MOE and MOR of bamboo laminated lumber, bonding with inner (low density surface) to inner surface, were better than that of outer (high density surface) to outer surface. It meant that MOE and MOR of bamboo laminated lumber were increased by the bonding surface density decreased of bamboo unit. Thickness swelling of carbonized bamboo laminated lumber was lower than that of bleached bamboo, which meant its dimensional stability was better than that of bleached bamboo laminated lumber.
21
Ji, Min, Wei Zhang, Guofu Wang, Yong Wang, and Hu Miao. "Online Measurement of Outline Size for Pinus Densiflora Dimension Lumber: Maximizing Lumber Recovery by Minimizing Enclosure Rectangle Fitting Area." Forests 13, no. 10 (October 3, 2022): 1627. http://dx.doi.org/10.3390/f13101627.
Testo completoAbstract (sommario):
This paper proposes a non-contact, online, rapid, and non-destructive measurement method of Pinus densiflora S.et Z. (Pinus densiflora) dimension lumber based on an algorithm of maximizing lumber recovery by minimizing the enclosure rectangle fitting area. The method takes the full influence of multiple factors, such as the difficulty in measuring large-size dimension lumber, conveying deflection, etc. into account. Image splicing, object and background segmentation, and lumber size measurements are carried out. Compared to other current algorithms, it can decrease the measurement errors and improve measurement efficiency. The problems of slow image segmentation, large-size lumber measurement, and conveying deflection are solved. Through measurement tests and error analysis, the measurement accuracy of the lumber size can reach 0.8 mm/m. This method meets the requirements of high-speed lumber production and lays the foundation for the development of a lumber detection and evaluation system.
22
Luppold, William G., and Matthew S. Bumgardner. "Influence of Markets and Forest Composition on Lumber Production in Pennsylvania." Northern Journal of Applied Forestry 23, no. 2 (June 1, 2006): 87–93. http://dx.doi.org/10.1093/njaf/23.2.87.
Testo completoAbstract (sommario):
Abstract In this study, we examine regional differences in the hardwood timber resources of Pennsylvania and how the combined changes in inventory volume, forest composition, and lumber prices have influenced regional lumber production. Isolation of these relationships is important because shifts in lumber production reflect changes in harvesting activity. In turn, harvesting influences long-term forest composition and structure. We define three hardwood regions in Pennsylvania based on forest composition and present a chronology of regional changes in sawtimber volumes, sawtimber composition, and lumber production. Regional changes in hardwood lumber production were found to be positively related to changes in the price of No. 1 Common lumber adjusted for changes in forest composition between 1970 and 1999. This finding supports our contention that regional changes in lumber production are influenced by a combination of changes in interspecies lumber price and changes in species availability.
23
Luppold, William, and Matthew Bumgardner. "Regional Analysis of Hardwood Lumber Production: 1963–2005." Northern Journal of Applied Forestry 25, no. 3 (September 1, 2008): 146–50. http://dx.doi.org/10.1093/njaf/25.3.146.
Testo completoAbstract (sommario):
Abstract Between 1963 and 2005 hardwood lumber production in the eastern United States increased by more than 50%. Production more than doubled in the northeastern and north central regions while increasing by less than 25% in the southeastern and south central regions. Increased lumber production in the northern regions was facilitated by an expanding sawtimber inventory, relative high volumes of select oak species and hard maple, an expanding kitchen cabinet industry, increased exports, and increased lumber demand by the pallet industry. Hardwood lumber production in the south central region was correlated with hardwood flooring production. When flooring production declined between 1963 and 1982, south central lumber production declined. After 1982 flooring production increased and hardwood lumber production in the south central region followed. By contrast, lumber production in the southeastern region has been tied to the fortunes of the wood and upholstered furniture industries. As furniture imports increased, the demand for lumber by these industries first stagnated and then declined. As a result, lumber production in this region declined between 1982 and 2005. Today, much of the commodity product portions of hardwood-demanding industries are facing international competition. By contrast, a driver of growth in hardwood lumber demand seems to be smaller manufacturers producing custom and semicustom products. These new industries tend to purchase higher-quality lumber but can use a variety of species. Therefore, states or regions with high volumes of timber and a broad composition of species have the greatest potential for future growth in hardwood lumber production.
24
Adhikari, Sailesh, Brian Bond, Henry Quesada, and Robert Smith. "Lumber Supply-Chain Practice in Cross-Laminated Timber Industries in the United States: A Comparison with Austrian Producers." Forest Products Journal 73, no. 4 (January 1, 2024): 370–77. http://dx.doi.org/10.13073/fpj-d-23-00018.
Testo completoAbstract (sommario):
Abstract Lumber is the main raw material for cross-laminated timber (CLT) production, accounting for up to 80 percent of the cost. The availability, quality, and price of lumber are critical factors that influence the completion of CLT projects in the United States. Although structural-rated CLTs are made from structural-grade lumber available in the commodities market, CLT mills have additional requirements to process the lumber more efficiently. These requirements increase production costs, affecting the supply chain, delaying production schedules, and increasing project completion times. This study aims to identify the differences in the lumber supply-chain practices for CLT manufacturing in the United States and Austria. The authors used the case-study survey with convenience sampling method to describe how CLT mills work with suppliers, their delivery preferences, quality-control practices, and current critical issues in each country. The study shows significant differences in lumber procurement and quality monitoring between CLT mills in the United States and Austria. Although the quality of lumber supplied to Austrian CLT mills does not require additional preparation, the quality of lumber in the United States significantly affects production efficiency and cost. To address the lumber supply-chain problems in the United States for CLT production, the authors recommend sorting lumber from the current market to meet minimum requirements and introducing a new lumber grade specifically for CLT mills. Furthermore, adopting the Austrian practice of mass-producing blank CLTs can provide a continuous supply of lumber from sawmills or distributors and increase collaboration opportunities with suppliers and producers.
25
Devadoss, Stephen. "An Evaluation of Canadian and U.S. Policies of Log and Lumber Markets." Journal of Agricultural and Applied Economics 40, no. 1 (April 2008): 171–84. http://dx.doi.org/10.1017/s1074070800023531.
Testo completoAbstract (sommario):
The recent lumber trade war between Canada and the United States deals with Canadian stumpage policies, Canada's log export controls, and U.S. retaliatory duty. This study determines the appropriate level of U.S. countervailing duty (CVD) by employing a vertically interrelated log–lumber model. The theoretical results show that the U.S. CVD can be greater (will be less) than the Canadian subsidy for a vertically related log–lumber market (for lumber market only). Empirical results support the theoretical findings in that the U.S. CVD for the log–lumber market (lumber market alone) is 1.55 (0.91) times the Canadian subsidy.
26
Devadoss, Stephen. "An Evaluation of Canadian and U.S. Policies of Log and Lumber Markets." Journal of Agricultural and Applied Economics 40, no. 01 (April 2008): 171–84. http://dx.doi.org/10.1017/s1074070800028042.
Testo completoAbstract (sommario):
The recent lumber trade war between Canada and the United States deals with Canadian stumpage policies, Canada's log export controls, and U.S. retaliatory duty. This study determines the appropriate level of U.S. countervailing duty (CVD) by employing a vertically interrelated log–lumber model. The theoretical results show that the U.S. CVD can be greater (will be less) than the Canadian subsidy for a vertically related log–lumber market (for lumber market only). Empirical results support the theoretical findings in that the U.S. CVD for the log–lumber market (lumber market alone) is 1.55 (0.91) times the Canadian subsidy.
27
Zhou, Hai Bin, and Hai Qing Ren. "Factors Influencing Structural Performance of Finger-Jointed Chinese Fir Lumber." Applied Mechanics and Materials 174-177 (May 2012): 635–40. http://dx.doi.org/10.4028/www.scientific.net/amm.174-177.635.
Testo completoAbstract (sommario):
Structural Finger-jointed (FJ) lumber is a common building material used mainly in timber construction. The paper evaluated the factors influencing structural performances of FJ Chinese fir lumber. Lumber was sawn from the logs following a pattern typically used in China to maximize the volume of recovered sawn timbers. After kiln-drying, the rough-sawed lumber was planned to 4.5 cm thick, 9.0 cm wide and 100cm long. The lumber pieces were assigned to two groups according to their dynamical MOE. FJ lumber is produced by cutting a series of sloping fingers on the end of the wood pieces to be joined and interlocking the two pieces by MDI glue. Bending and tensile strengths of FJ lumber were tested. The results show that the structural performance of the MSR FJ lumber was increased effectively after these units were machine-graded in advance and the interaction of variables should be considered in the design of finger joints.
28
Yamamura, Satoshi, Itsushi Baba, Yoshihisa Ishida, Tadayuki Sumida, Hideki Manabe, Kenji Yamamoto, and Hidetoshi Ohta. "Recurrent Lumbar Disc Herniation. Relationship with Lumber Canal Stenosis." Orthopedics & Traumatology 43, no. 2 (1994): 522–25. http://dx.doi.org/10.5035/nishiseisai.43.522.
Testo completo
29
Toyota, Kouichiro, Toshihiko Taguchi, Yutaka Ito, Hiroshi Onaka, Shinya Kawai, Yasunori Fuchigami, and Hirotsugu Oda. "Enlargement of Lumbar Vertebral Canal for Lumber Degenerative Scoliosis." Orthopedics & Traumatology 50, no. 4 (2001): 1181–83. http://dx.doi.org/10.5035/nishiseisai.50.1181.
Testo completo
30
Arabi, Mohammad, Moharam Hazrati, and Akbar Rostampour-Haftkhani. "Performance of laminated veneer lumber panels from fast-growing species with different layering arrangements." BioResources 19, no. 2 (March 1, 2024): 2546–61. http://dx.doi.org/10.15376/biores.19.2.2546-2561.
Testo completoAbstract (sommario):
This study investigated the effect of various layer arrangements and their impact on the properties of laminated veneer lumber (LVL). Seven different layer arrangements (CCCCCCC, DDDDDDD, PPPPPPP, CDDDDDC, CPPPPPC, CDDCDDC, CPPCPPC, CDCDCDC, CPCPCPC, CCDDDCC, CCPPPCC, CCDCDCC, and CCPCPCC) were used in the manufacturing of the LVL, with each arrangement represented by a combination of the three wood species: hornbeam (C), paulownia (P), and poplar (D). The veneers were bonded with a polyurethane adhesive and pressed under 1 MPa pressure. The physical and mechanical properties of the laminated veneer lumber, including modulus of rupture, modulus of elasticity, block shear, delamination, and swelling, were measured under both dry and cyclic conditions (boil and dry). The modulus of rupture and modulus of elasticity of the LVLs increased when the proportion of hornbeam in the lamination increased. In the cyclic boil-dry condition, the laminated veneer lumbers with the configurations CPCPCPC and CDCDCDC showed the best structural performance. Furthermore, the study found that when one or two upper layers of poplar and paulownia were replaced with hornbeam layers, cracks were observed in the laminated veneer lumber samples. However, when the layers of poplar and paulownia were replaced with hornbeam alternately, no cracks were observed after saturating the laminated veneer lumber with water. The utilization of an alternating arrangement of poplar and paulownia layers with hornbeam in LVL can be used as an effective and cost-efficient approach for enhancing and reinforcing the LVL performance.
31
Eastin, Ivan L., and Jun Fukuda. "The impact of regulatory change on the international competitiveness of the Canadian softwood lumber industry." Forestry Chronicle 77, no. 2 (April 1, 2001): 315–23. http://dx.doi.org/10.5558/tfc77315-2.
Testo completoAbstract (sommario):
The decade of the 1990s have seen the introduction of several regulatory changes in international markets that have had a dramatic impact on the competitiveness of the Canadian softwood lumber industry. These regulatory changes have occurred in virtually every major market to which Canadian softwood lumber manufacturers export, including Europe, the US, and Japan. The objective of this paper is to describe the regulatory changes that have been implemented in the major markets for Canadian softwood lumber and provide an objective discussion of the impact of these changes on the international competitiveness of Canadian softwood lumber. Key words: softwood lumber, non-tariff barriers, international trade, Softwood Lumber Agreement (SLA), pinewood nematode, regulatory change, international competitiveness
32
Shook, Steven R., Jorge A. Soria, and Darek J. Nalle. "Examination of North American softwood lumber species substitution using discrete choice preferences and disaggregated end-use markets." Canadian Journal of Forest Research 37, no. 12 (December 2007): 2521–40. http://dx.doi.org/10.1139/x07-091.
Testo completoAbstract (sommario):
Over the past 20 years, four significant and contentious softwood lumber trade disputes have taken place between the United States and Canada. The US International Trade Commission (USITC), relying on aggregate market assessments using elasticity of demand estimation and cointegration methods, has ruled that all North American softwood lumber species are perfectly fungible. The objective of this study is to disaggregate the US softwood lumber market by estimating cross-price elasticity of demand for North American softwood lumber species and species groups in three major end-use markets (floor framing, roof framing, and wall framing products) using a discrete choice preference model. Specifically, this study utilizes a choice-based conjoint model to estimate species and species group preferences, market shares, and price-demand relationships for North American softwood lumber. Research results are compared with published aggregate market cross-price elasticity of demand estimates, such as those relied upon by USITC, to determine whether North American softwood lumber species and species groups are perfectly fungible in the three largest softwood lumber end-use markets. Results demonstrate that distinct differences exist in the substitutability between North American species and species groups of softwood lumber. The results provide notable implications in future USITC trade analyses of the US–Canadian softwood lumber trade issue.
33
Rozas, Carlos, Barbara Zapata, Fernando Muñoz, Virna Ortiz-Araya, and Oswaldo Erazo. "Characterization and Yield of Eucalyptus regnans F. Muell Logs for Lumber Production." Forests 14, no. 12 (November 30, 2023): 2359. http://dx.doi.org/10.3390/f14122359.
Testo completoAbstract (sommario):
The yield of Eucalyptus regnans logs for lumber production was evaluated. Crack width and length at each log end were measured. Two log-cutting plans were used to obtain sawn lumber. The first plan (PA) considered logs with diameters varying from 28 to 40 cm, and in the second plan (PB), the log diameters ranged from 42 to 56 cm (PB). Lumber yield was determined using two log volume methods: the Japanese Agricultural Standards (JAS) and Smalian’s equation. The deformations of E. regnans lumber were measured. The Australian and Chilean standards were used to classify sawn lumber. The results showed that logs had radial cracks at both log ends. Cracks were classified into two groups, considering the crack length. Regarding the lumber deformations, most boards exhibited level B bows and crooks in both cutting plans. Levels A and B twists were prevalent in PA, whereas in PB, level A significantly outnumbered level B. The lumber yield of E. regnans in PB was higher than in PA. The lumber yield determined by Smalian’s equation was higher than that determined by the JAS method. This research provides insight into the characterization of E. regnans for lumber production, highlighting its relevance in the forestry industry.
34
Kim, Chul-Ki, Da-Bin Song, and Kug-Bo Shim. "Evaluation of the tensile strength of Korean yellow poplar lumber." BioResources 19, no. 1 (January 5, 2024): 1260–73. http://dx.doi.org/10.15376/biores.19.1.1260-1273.
Testo completoAbstract (sommario):
This study was conducted to confirm the feasibility of using yellow poplar, which is a fast-growing hardwood species in Korea, as a structural material. Lumber was produced, and the mechanical grading and the knot diameter ratio on the wide surface measurement were performed for each grade of lumber. It was confirmed that the majority mechanical grades of yellow poplar were E10, E11, and E12, and the size of knot in the surface increased as the mechanical grades decreased. A fitted distribution of tensile strength of the lumbers was the Weibull distribution. As a result of calculating the tensile allowable stress using the 5th percentile value calculated by the Weibull distribution and the non-parametric method according to the mechanical grade, all the experimental values were higher than the minimum allowable stresses presented in the Korean industrial standards. However, for the low grades, there was no significant difference from the standard values. This was thought to be due to the large size of knots in low-grade lumber. It was expected that the prospect of using yellow poplar structural member will be higher if additional research is conducted on the restriction of knot size according to the mechanical grade.
35
Liu, Chuangmin, Jean-Claude Ruel, Art Groot, and S. Y. Zhang. "Model development for lumber volume recovery of natural balsam fir trees in Quebec, Canada." Forestry Chronicle 85, no. 6 (December 1, 2009): 870–77. http://dx.doi.org/10.5558/tfc85870-6.
Testo completoAbstract (sommario):
To improve the precision of sawing simulations, 4 regression models were developed to predict simulated lumber volume recovery using tree size variables. Simulated lumber volume recoveries from natural balsam fir trees based on the sawing simulator Optitek were different from real lumber volume recoveries from a stud sawmill because the simulation method only takes wane into consideration. Therefore, 2 methods were developed to correct estimated lumber volume recoveries. The results indicate that the lumber volume correction models for stem deformations could adjust the predictions of lumber volume recovery from the simulation and directly from the sawing simulator to obtain more accurate estimates. With the correction models, the lumber volume recovery from natural balsam fir trees could be estimated directly using easily measured tree DBH and height from the forest resource inventory. Key words: balsam fir, stem deformation, product recovery, sawing simulation, correction models, regression model
36
Li, Yanshu, and Daowei Zhang. "Incidence of the 1996 U.S.–Canada Softwood Lumber Agreement among Landowners, Loggers, and Lumber Manufacturers in the U.S. South." Forest Science 52, no. 4 (August 1, 2006): 422–31. http://dx.doi.org/10.1093/forestscience/52.4.422.
Testo completoAbstract (sommario):
Abstract A framework was developed to estimate the welfare incidence of the 1996 U.S.–Canada Softwood Lumber Agreement among producers in two-processing-stage markets—timberland owners, loggers, and lumber manufacturers—in the U.S. South. Timberland owners are the largest beneficiary whereas lumber manufacturers are the second and loggers the least. Empirically, without considering substitution effects among production inputs, timberland owners have 47.4% of total incremental producer surplus, whereas lumber manufacturers have 39.4% and loggers 13.2%. When the substitution effects are considered, timberland owners gain slightly less whereas lumber manufacturers and loggers gain slightly more.
37
Patterson, David W., Paul A. Murphy, and Michael G. Shelton. "Effects of Stand and Site Variables on the Lumber Value of Uneven-aged Loblolly Pine Stands." Southern Journal of Applied Forestry 24, no. 4 (November 1, 2000): 202–6. http://dx.doi.org/10.1093/sjaf/24.4.202.
Testo completoAbstract (sommario):
Abstract Uneven-aged silviculture using single-tree selection provides the landowner with periodic income from a continuous forest which has a varied canopy. Data were collected from 24 plots of a larger study to determine if site index, basal area, and maximum dbh affected volume and value of lumber from loblolly pine (Pinus taeda L.) trees in uneven-aged stands. Tree grades and lumber yield equations were used to determine the volume of lumber by grade for each tree. Market prices from May 1997 and May 1998 were used to estimate lumber value. Analysis of variance showed that study variables significantly affected lumber volume, lumber value/mbf, and stand value/ac. With 1997 prices, increases in site index and maximum dbh significantly increased lumber value/mbf, but only maximum dbh was significant with 1998 prices. Stand values ranged from $4,100 to $12,350/ac and were significantly higher for the higher site index, basal area, and maximum dbh. South. J. Appl. For. 24(4):202-206.
38
Zhou, Chengmin, Ziyan Shi, and Jake Kaner. "Life cycle analysis for reconstituted decorative lumber from an ecological perspective: A Review." BioResources 17, no. 3 (May 26, 2022): 5464–84. http://dx.doi.org/10.15376/biores.17.3.zhou1.
Testo completoAbstract (sommario):
In response to global Sustainable Development Goals (SDGs), the Chinese government has pledged to curtail increased carbon dioxide emissions beyond 2030 and to achieve carbon neutrality by 2060, thus achieving a status of an ecological civilization. Reconstituted decorative lumber, with rotary-cut (or planed) veneer from plantation or common species timber as the main raw material, has beneficial development opportunities for forestry from the perspective of an ecological civilization. This paper first discusses China’s current state of ecological civilization, then researches the various life cycles of reconstituted decorative lumber using the life cycle theory and provides a reference for the Chinese reconstituted decorative lumber industry’s development by analyzing progress in related fields. The eco-friendliness of reconstituted decorative lumber is explained via systematic combing, and proposals for the use and promotion of reconstituted decorative lumber in the new period are presented. Research and analysis findings show that it is necessary to comprehensively regulate the production chain of reconstituted decorative lumber based on life cycle. Research on the development and utilization of reconstituted decorative lumber needs to be strengthened. The promotion and marketing of reconstituted decorative lumber can be promoted by emphasizing its ecological significance.
39
Tao, Wendong. "Field leaching of alkaline copper quaternary-treated red pine lumber over 3 years: long-term dynamics." Water Science and Technology 69, no. 7 (January 27, 2014): 1475–81. http://dx.doi.org/10.2166/wst.2014.045.
Testo completoAbstract (sommario):
Alkaline copper quaternary (ACQ), a wood preservative, consists of copper oxide and quaternary ammonium compounds. Three red pine piles were monitored over 3 years to evaluate the dynamics of contaminant leaching from ACQ-treated and untreated lumber. There were small temporal changes in the volumetric leachate/rain ratio with the ACQ-treated lumber, while the volumetric ratio decreased across the 3 years with the untreated lumber, most likely due to considerable weathering that increased the capacity of the untreated lumber to absorb rain water. The average copper (Cu) concentration in leachate from the ACQ-treated lumber (4,033 μg/L) was much higher than that in leachate from the untreated lumber (87 μg/L) and rain (48 μg/L) in the first leaching year. Cu concentration in leachate from the ACQ-treated lumber in the second and third years decreased to 46–51% of that in the first year. There were significant seasonal decreases of Cu concentration in leachate from the ACQ-treated lumber, which were correlated to exposure time and meteorological parameters. ACQ-treatment did not affect leachate pH and concentrations of quaternary ammonium compounds and chemical oxygen demand. There were insignificant temporal changes of leachate pH and concentrations of chemical oxygen demand and total dissolved solids in leachate from both ACQ-treated and untreated lumber piles.
40
Cohen, David H. "A history of the marketing of British Columbia softwood lumber." Forestry Chronicle 70, no. 5 (October 1, 1994): 578–84. http://dx.doi.org/10.5558/tfc70578-5.
Testo completoAbstract (sommario):
This paper provides a historical account of the marketing of British Columbia softwood lumber, one of Canada's pioneering lumber exporting regions. History teaches lessons concerning cooperation, the necessity for market diversity, and understanding customers' perspectives. As customer orientation becomes increasingly important for lumber producers to maintain and/or improve their international competitive position, foresters need to become more aware of the international marketing of wood products. Understanding the history of marketing B.C. lumber products can provide the foundation for foresters to help plan future exporting accomplishments. Key words: lumber exporting, forest product marketing, forest history, British Columbia forest products
41
Krahn, Peter K., and Julie A. Shrimpton. "Stormwater Related Chlorophenol Releases from Seven Wood Protection Facilities in British Columbia." Water Quality Research Journal 23, no. 1 (February 1, 1988): 45–54. http://dx.doi.org/10.2166/wqrj.1988.004.
Testo completoAbstract (sommario):
Abstract Stormwater run-off at five sawmills and two lumber export terminals was collected and analyzed for 2,3,4,6-tetrachlorophenol and pentachlorophenol. Leaching from treated lumber began after 1.0 to 1.5 mm of continuous rainfall. Dip treated lumber leached up to 158,000 micrograms per litre (ug/L) and generated runoff with up to 6,600 ug/L total Chlorophenols. Low pressure sprayed lumber leached up to 576,000 ug/L total Chlorophenols and generated runoff with up to 27,000 ug/L. High pressure sprayed lumber leached up to 9,800 ug/L and generated average yard runoff up to 1,968 ug/L total Chlorophenols.
42
Dwyer, John P., and Kim E. Lowell. "Long-Term Effects of Thinning and Pruning on the Quality, Quantity, and Value of Oak Lumber." Northern Journal of Applied Forestry 5, no. 4 (December 1, 1988): 258–60. http://dx.doi.org/10.1093/njaf/5.4.258.
Testo completoAbstract (sommario):
Abstract After 32 years, experimental plots established to examine thinning levels and pruning effects were harvested. Randomly selected trees in each treatment were felled and sawn into 4/4 lumber, and the lumber from each tree was tallied by grade. For black oak, the species that became largely relegated to the understory, thinning caused a significant increase in the total volume outturn with the greatest increase occurring in the lowest lumber grade (3B). For scarlet oak, the species that became primarily dominant and codominant, thinning increased the total lumber yield per tree with most of the increase accumulating in the lumber grades #1C and #2C. Pruning did not affect the quantity or quality of lumber outturn in either species. North. J. Appl. For. 5:258-260, December 1988.
43
da Rosa Azambuja, Rafael, David B. DeVallance, and Joseph McNeel. "Evaluation of Low-Grade Yellow-Poplar (Liriodendron tulipifera) as Raw Material for Cross-Laminated Timber Panel Production." Forest Products Journal 72, no. 1 (December 14, 2021): 1–10. http://dx.doi.org/10.13073/fpj-d-21-00050.
Testo completoAbstract (sommario):
Abstract Utilization of low-grade yellow-poplar (Liriodendron tulipifera) lumber would provide for alternative structural lumber sources and promote the growth of cross-laminated timber (CLT) manufacturing facilities within the Appalachian Region. A significant amount of low-grade yellow-poplar lumber (i.e., National Hardwood Lumber Association [NHLA] No. 2A and Below Grade) is utilized for wood pallets. In practice, this material is not graded for structural purposes. Additionally, research on yellow-poplar for structural use has focused on grading lumber from a small population of selected logs, not by regrading NHLA lumber from manufacturing facilities. Therefore, the research's objective was to investigate the structural grades of a typical population of NHLA graded No. 2 and lower lumber and evaluate their potential to meet structural grades necessary for CLT panels. NHLA graded lumber was regraded and assigned to visual structural grades following Northeastern Lumber Manufacturers Association rules and evaluated for flatwise bending modulus of elasticity (MOEb) by nondestructive proof loading. The results of the study indicated that 54.6 percent of the boards possessed a minimal structural visual grade required for CLT panels according to American National Standards Institutes/The Engineered Wood Association (ANSI/APA) PRG 320-2019 (2020). Splits were the most common limiting defect that downgraded boards to nonstructural grades. Also, 96.6 percent of the boards evaluated had a MOEb above the required minimal board value of 1.2 ×106 psi (8,274 MPa) listed in ANSI/APA PRG 320-2019 (2020). The results of the study indicated that a majority of NHLA low-grade yellow-poplar, when regraded for structural purposes, meets or exceeds minimum lumber grade values necessary for use in CLT panel production.
44
Saud, Pradip, Jingxin Wang, Benktesh D. Sharma, and Weiguo Liu. "Carbon impacts of hardwood lumber processing in the northeastern United States." Canadian Journal of Forest Research 45, no. 12 (December 2015): 1699–710. http://dx.doi.org/10.1139/cjfr-2015-0082.
Testo completoAbstract (sommario):
Carbon emission from hardwood lumber processing in different-sized sawmills under varying energy sources, management strategies, and potential carbon offsetting capacity through useful life (service life) of lumber in the northeastern United States was analyzed using analytical statistics such as analysis of variance (ANOVA), mixed-effect model, principal component analysis, and Monte Carlo simulation. Data obtained from a regional sawmill survey (Pennsylvania, New York, Ohio, and West Virginia), energy audit of sawmills, public databases, and relevant literature were analyzed for the gate-to-gate life cycle inventory framework. Results showed that mean carbon emission (megagrams (Mg) per thousand cubic metres (TCM)) for lumber processing significantly differs among sawmill sizes. The total carbon emission from electricity consumption and wood residue of lumber processing was approximately 62.5%, 80.3%, and 66.2% of carbon stored in lumber processed for small, medium, and large sawmills, respectively. Efficient management and potential opportunities of improvement in sawmills can significantly reduce carbon emission (10.96% ± 1.57%) from hardwood lumber processing. Carbon stock from lumber production could be enhanced by either reducing carbon emission from energy consumption or decreasing lumber export quantity. The carbon emission–loss ratio (CELR) suggested that after 100 years, nearly 50% of carbon stored in lumber would be still available for carbon accountability. Electricity generation from either a single resource (natural gas) or mixed resources as is the case in RFC EAST (eGrid subregion) would be beneficial in lowering carbon emission from sawmill processing.
45
Williamson, T., G. Hauer, and M. K. Luckert. "A restricted Leontief profit function model of the Canadian lumber and chip industry: potential impacts of US countervail and Kyoto ratification." Canadian Journal of Forest Research 34, no. 9 (September 1, 2004): 1833–44. http://dx.doi.org/10.1139/x04-058.
Testo completoAbstract (sommario):
Estimation of output supplies and factor demands with a range of functional forms provides a basis for bounding possible supply responses to exogenous shocks. No prior study, to our knowledge, has used a generalized Leontief functional form to estimate lumber and chip supply responses in Canada. The own price lumber supply elasticities estimated from the restricted Leontief profit functional form used in this study are lower than those presented in most other studies, while the lumber supply response with respect to roundwood price change is somewhat higher than some studies. We simulate the impacts of current US countervail processes on Canadian lumber supply. The simulated responses to duties might be considered to be conservative estimates, while the lumber supply responses to roundwood price increases could be on the high end of expected responses. Estimation of profit and supply functions indicates that rather than being a distinct production decision, chip supply follows lumber supply. The supply responses of chips and lumber to the various combinations of duty, roundwood price increases, and energy price increases indicate a number of patterns. First, if Kyoto policies increase energy prices (up to 10%), these changes are not likely to have a large impact on lumber and chip production. Second, British Columbia and Quebec tend to have lumber and chip supplies that are more sensitive to duties and increased roundwood prices than Ontario. Third, Quebec is more sensitive to roundwood price increases, while British Columbia is more sensitive to the effects of duties.
46
Reid, Douglas E. B., Steven Young, Queju Tong, S. Y. Zhang, and Dave M. Morris. "Lumber grade yield, and value of plantation-grown black spruce from 3 stands in northwestern Ontario." Forestry Chronicle 85, no. 4 (August 1, 2009): 609–17. http://dx.doi.org/10.5558/tfc85609-4.
Testo completoAbstract (sommario):
Three black spruce plantations in northwestern Ontario, with varied stand densities and site indices were studied to determine lumber properties and yield. Based on visual grading rules, each stand produced at least 87% No. 2 and Better grade lumber. Wane and skip were the 2 most prominent defects causing lumber downgrades. The compliance of visually graded No. 2 and Better lumber with bending modulus of elasticity (MOE) design values for visual grades varied among stands, as did the proportion that qualified as machine stress-rated (MSR) lumber. MOE and Modulus of Rupture (MOR) differed among stands, consistent with differences in MSR yield. The stand with the highest density and the lowest site index produced the highest yield of MSR grade lumber, but not the highest compliance with bending MOE design values. Regardless of the grading scenario, the most productive stand with the largest average tree size produced the highest value per hectare ($28K per ha) under an MSR grading scenario. These results suggest that MSR grading can improve revenues, and that it will be needed to maintain market confidence in the quality of lumber from second-growth black spruce stands. Key words: lumber quality, Picea mariana (Mill.) BSP, market value, density regulation, stand-level effects, intensive silviculture
47
Gan, Jianbang, Nana Tian, Junyeong Choi, and Matthew H. Pelkki. "Synchronized movement between US lumber futures and southern pine sawtimber prices and COVID-19 impacts." Canadian Journal of Forest Research 52, no. 4 (April 2022): 614–21. http://dx.doi.org/10.1139/cjfr-2021-0326.
Testo completoAbstract (sommario):
We analyzed the synchronized movements of lumber futures and southern pine sawtimber stumpage prices in the United States since 2011 and their response to COVID-19 events using wavelet analysis and event study. We found that the sawtimber and lumber prices have followed complex comovement patterns in the time–frequency domain and both reacted to COVID-19 events with a higher response intensity of the lumber price. Although they reacted differently to the early COVID-19 episodes and vaccine news, the sawtimber and lumber prices responded similarly to the COVID-19 pandemic declarations by the World Health Organization and US president, the US Food and Drug Administration panel’s recommendation of the first COVID-19 vaccine, and economic stimulus legislation. The patterns of synchronized movements between the sawtimber and lumber prices varied with time and frequency, but their comovement at low frequencies (>64 weeks) has strengthened since 2014 and been led by the lumber futures price; COVID-19 episodes have not changed this trend. The different magnitude of response of the two prices to the COVID-19-related events, as well as the long-term dominance of the lumber price in the comovement, reveals asymmetric price negotiation power and benefit distributions among the agents of the lumber value chain.
48
Tomporoski, Alexandre Assis, Patricia Minini Wechinewsky Guerber, Juliana Maciel, Evelyn Bueno Vicente de Lima, and Daiani Amaral. "Contestado e o passado que não passsa." Profanações 10 (August 23, 2023): 320–43. http://dx.doi.org/10.24302/prof.v10.2999.
Testo completoAbstract (sommario):
O objetivo deste artigo consiste em examinar os desdobramentos do processo de estatização da Southern Brazil Lumber and Colonization Company, culminando com a transformação de sua sede no Campo de Instrução Marechal Hermes. A abordagem considera o enfoque da História Social Inglesa – especialmente as noções sugeridas por Thompson – na perspectiva da reciprocidade entre a classe trabalhadora e as classes dominantes, além de suas relações com o Estado. Dentre os resultados do estudo, descreve-se: as mudanças na cultura organizacional da Lumber Incorporada após os militares assumirem o controle da administração; as aparentes irregularidades no processo de venda do acervo de bens da Lumber Incorporada; a suspeição acerca da atuação do então governador do estado de Santa Catarina, Irineu Bornhausen; a atuação com segundas intenções do empresário Alberto Dalcanale, que cedeu a área de terras da sede da Lumber Incorporada ao Ministério da Guerra; a agonia dos trabalhadores da Lumber Incorporada em longos períodos de atraso nos pagamentos de salários; o processo injusto de desapropriações de áreas de terras contíguas à Lumber Incorporada, para fins de composição do campo militar. Concluí-se que a presença da Lumber Company afetou decisivamente o curso dos eventos na região sob sua influência. Palavras chave: Lumber Company. Nacionalização. Contestado.
49
Luppold, William G., and John E. Baumgras. "Price Trends and Relationships for Red Oak and Yellow-Poplar Stumpage, Sawlogs, and Lumber in Ohio: 1975-1993." Northern Journal of Applied Forestry 12, no. 4 (December 1, 1995): 168–73. http://dx.doi.org/10.1093/njaf/12.4.168.
Testo completoAbstract (sommario):
Abstract The rapidly changing domestic and international hardwood markets of the 1980s had a large impact on the demand and price of hardwood lumber, logs, and stumpage. In this paper we examine inflation adjusted (real)prices for red oak and yellow-poplar stumpage, logs, and lumber. We then relate the observed trends to changes in domestic lumber consumption, lumber and log exports, sawmill technology, and forest inventory trends. Increasing real prices for red oak stumpage, logs, and lumber are the result of expanding domestic and international demand coupled with relatively limited stumpage supplies. Yellow-poplar, a species in relatively abundant supply and lower demand, experienced a decline in real prices for logs and lumber. Gains in stumpage prices have exceeded those for both logs and lumber, indicating that stumpage prices have benefited from transferred efficiencies in harvesting and milling. Although this study focuses on stumpage and log prices in Ohio from 1975 to 1993, the results appear to be relevant to adjacent states. North. J. Appl. For. 12(4):168-173.
50
He, Mingtao, Wenying Li, Brian K. Via, and Yaoqi Zhang. "Nowcasting of Lumber Futures Price with Google Trends Index Using Machine Learning and Deep Learning Models." Forest Products Journal 72, no. 1 (December 17, 2021): 11–20. http://dx.doi.org/10.13073/fpj-d-21-00061.
Testo completoAbstract (sommario):
Abstract Firms engaged in producing, processing, marketing, or using lumber and lumber products always invest in futures markets to reduce the risk of lumber price volatility. The accurate prediction of real-time prices can help companies and investors hedge risks and make correct market decisions. This paper explores whether Internet browsing habits can accurately nowcast the lumber futures price. The predictors are Google Trends index data related to lumber prices. This study offers a fresh perspective on nowcasting the lumber price accurately. The novel outlook of employing both machine learning and deep learning methods shows that despite the high predictive power of both the methods, on average, deep learning models can better capture trends and provide more accurate predictions than machine learning models. The artificial neural network model is the most competitive, followed by the recurrent neural network model.