Tesi sul tema "Liaison céramique"
Cita una fonte nei formati APA, MLA, Chicago, Harvard e in molti altri stili
Vedi i top-26 saggi (tesi di laurea o di dottorato) per l'attività di ricerca sul tema "Liaison céramique".
Accanto a ogni fonte nell'elenco di riferimenti c'è un pulsante "Aggiungi alla bibliografia". Premilo e genereremo automaticamente la citazione bibliografica dell'opera scelta nello stile citazionale di cui hai bisogno: APA, MLA, Harvard, Chicago, Vancouver ecc.
Puoi anche scaricare il testo completo della pubblicazione scientifica nel formato .pdf e leggere online l'abstract (il sommario) dell'opera se è presente nei metadati.
Vedi le tesi di molte aree scientifiche e compila una bibliografia corretta.
Zanchetta, Armando. "La liaison céramique-métal : cas du système procelaine/kovar". Limoges, 1993. http://www.theses.fr/1993LIMO0457.
Testo completoVALAUD, MIREILLE. "Liaison céramique-métal : comportement en frottement à sec de matériaux céramiques déposés sur un substrat métallique". Limoges, 1989. http://www.theses.fr/1989LIMO0048.
Testo completoGréard, Traut Elisabeth. "Compréhension des mécanismes de frittage réactif de céramiques à liaison sialon". Châtenay-Malabry, Ecole centrale de Paris, 2000. http://www.theses.fr/2000ECAP0863.
Testo completoGaussens, Clélia. "Solutions adhésives et durabilité d'une liaison structurale d'un capteur céramique sur un roulement acier". Thesis, Toulouse, INPT, 2010. http://www.theses.fr/2010INPT0112/document.
Testo completoThe industrial application (under a confidential clause) concerns a ceramic/steel assembly. This PhD research take part in a European programme and is concerned with providing a reliable industrial bonding between ceramic and steel using structural adhesive.This assembly should ensure the total transmission of the efforts on a broad range of temperatures and in a hard life requirements. The methodology consists in the definition of formulations parameters impact on the initial properties and the durability of the assemblies. The study of the parameters which are the macromolecular chain of the epoxy resin, the nature of the hardener and filler addition have lead to the selection of formulations containing DGEBA (diglycidylether of the bisphenol A) and Novolaque alone or melted. The determination of their properties highlights different behaviors in terms of glassy transition temperature, curing process, viscosity and adherence. The characterization of the formulations during hydrothermal ageing shows common non reversible chemical modifications (IRTF) but different physical behaviors (thermomechanical analysis, SEM, flexion, calorimetry) and water sorption modes (Gravimetry, TGA). The adherence tests (crown test and three point flexure test) developed in order to characterize the interfaces behavior show higher durability of the melted systems comparing to the DGEBA formulation. A non destructive test study highlights the conservation ceramic/adhesive /steel assembly’s integrity submitted to harmful conditions as residual stresses, hydrothermal ageing and thermal shock
Béraud, Catherine. "Contribution par M. E. T. A l’étude de la liaison cuivre-aluminium". Lyon, INSA, 1986. http://www.theses.fr/1986ISAL0017.
Testo completoMbongo, Bonaventure. "Liaison métal-céramique par thermocompression : Influence de l'état initial des matériaux et de la pression partielle d'oxygène". Ecully, Ecole centrale de Lyon, 1994. http://bibli.ec-lyon.fr/exl-doc/TH_T1583_bmbongo.pdf.
Testo completoChanson, Charlotte. "Optimisation de la liaison interfaciale dans les composites à matrice céramique renforcés par des fibres Hi-Nicalon S". Thesis, Bordeaux, 2015. http://www.theses.fr/2015BORD0222.
Testo completoMechanical properties of ceramic composites can be improved by controlling interfacial bonding and choosing materials. To enhance interfacial bonding, treatment on the last SiC fiber, Hi-Nicalon S surface are proposed in this work. The aim is to allow chemical and/or mechanical bonds mainly with BN interphase. For this, composites models, minicomposites are elaborated by CVI (Chemical Vapor Infiltration). Quantification of the strength of interfacial bonding is based by evaluating interfacial bonding energy Gci with tensile tests, and by calculating interfacial shear stress τ with push-out tests. Firstly, Hi-Nicalon S fibers whose surfaces have been slightly modified have been tested with classic interphase PyC. Interfacial bonding on minicomposites is weak. Different treatments have been performed on surface fibers to enhance interfacial bonding with BN, which have a better resistance oxidation than PyC. Before, elaboration parameters of BN interphase have been studied
Hattali, Lamine. "Caratérisation et modélisation thermo-mécaniques des assemblages métal-céramique élaborés par thermocompresion". Ecully, Ecole centrale de Lyon, 2009. http://www.theses.fr/2009ECDL0002.
Testo completoPeytour, Claude. "Étude de la microstructure et des propriétés mécaniques de liaisons céramique-métal entre Al₂O₃, ZrO₂ , Si₃N₄ et l'alliage TA6V". Paris 11, 1989. http://www.theses.fr/1989PA112329.
Testo completoHattali, Lamine. "CARACTÉRISATION ET MODÉLISATION THERMO-MÉCANIQUES DES ASSEMBLAGES MÉTAL-CÉRAMIQUE ÉLABORÉS PAR THERMOCOMPRESSION". Phd thesis, Ecole Centrale de Lyon, 2009. http://tel.archives-ouvertes.fr/tel-00505340.
Testo completoCazajus, Vincent. "Approches numérique et expérimentale de la liaison céramique métal réalisée par brasage en vue de la création d'un outil d'aide à la conception". Toulouse, INPT, 2007. https://hal.science/tel-04582504.
Testo completoCeramic and metallic materials are joined together in order to associate the different but complemantary properties of these two kind of materials. The main difficulties in ceramic to metal joining are based on the behaviour difference between these materials. Notably, the difference between the thermal expansion coefficient leads to the development of residual stresses after the braze alloy solidification (780°C) during brazing process. The framework of this study is to develop a conception tool for the ceramic metal brazed assemblies which allows to reduce the residual stresses values and to ensure its performance. The work has been organised in three major steps : the behaviour law identification of each materials of the assembly, the definition of the numerical conception tool and then the experimental validation of the residual stresses and mechanical behaviour estimation
Caboche, Juline. "Développement d’assemblages brasés céramique-métal à haute tenue en température dans un environnement agressif". Thesis, Paris Sciences et Lettres (ComUE), 2017. http://www.theses.fr/2017PSLEM076.
Testo completoAerospace technology developments are blooming. Since the 1960’s the Turbine Entry Temperature for aero-engines gas turbines keeps rising to improve their efficiency. Sensors working close to the combustion chamber are required in order to master the turbine performances. This results in an industrial urge to develop ceramic-to-metal assemblies able to endure severe engine environment (>1100°C under air, vibrations, etc.)The choice of an alumina as the ceramic part ensures a good insulation at high temperature. The main issue remains the metallic material which must be refractory, resistant to oxidation and affordable. The application of a ternary carbide (phase MAX) is tested. The braze alloy composition is adjusted to each system so as to provide a good ductility, thermal stability and a metallurgical matching as regards dissolution and brittle compounds formation.Braze alloys based on the Au-Pd-Pt system are investigated. The aforesaid liquidus and solidus surfaces are defined from experimental measures. Diffusion, dissolution and inter-granular penetration at the metal/braze alloy interface are described to suggest improvements. Aluminum diffusion from alumina-forming materials towards the braze alloy is the dominant phenomenon during brazing, despite the use of a diffusion barrier. The use of noble materials for the metallic substrate is mandatory.Geometrical and chemical assembly parameters are defined for selected brazed system based on the physicochemical interactions occurring during brazing and aging under air. The best brazed assemblies present an excellent hermeticity after brazing. Thermal cycling aging in severe conditions is detrimental to ceramic-braze alloy bonding, leading to interfacial cracks. Two promising strategies are suggested to ensure a reliable ceramic-to-braze alloy bonding during thermal cycling
Contri, Boris. "Procédés d’assemblages céramique – métal : étude des couples Inconel®625 – Alumine et Titane Zirconium Molybdène (TZM) – Carbure de silicium". Electronic Thesis or Diss., Limoges, 2023. http://www.theses.fr/2023LIMO0093.
Testo completoThis work has for objective to present the results obtained for the ceramic-metal bonding by hot-pressing in two cases: Inconel®625 / Alumina and TZM / Silicon carbide. All the thesis take place according to the last results obtained for similar bonding, in the laboratory IRCER, by studying the feasibility of direct bonding and bonding after pre-oxidising the metal part. A part of this study is then dedicated to the oxidation behaviour of inconel®625 under CO2 using a thermobalance with a sample hot introduction. Using the oxidation kinetics obtained, the reaction mechanism is proposed and the conditions for the metal pre-oxidation determined.Then during the manuscript are presented the processes and the results obtained after variations of parameters such as temperature and the heat treatment time for the two couples of materials. The absence of inter-phase formation in the couple Inconel®625 / Alumina and the formation of a complex inter-phase in the couple TZM / Silicon carbide allow us to propose two studies with different metal-ceramic bonding.A last part is dedicated to the characterization and the understanding of the bonding obtained in each case. To explain the properties of the samples obtained we used scaning electron microscopy but also numerical simulation for the first couple Inconel®625 / Alumina and tensile test for the second couple TZM / Silicon carbide
Klein, Robert. "Propriétés de composites céramiques particulaires électroconducteurs, élaborés par compression isostatique à chaud". Limoges, 2004. http://aurore.unilim.fr/theses/nxfile/default/87d1df87-738c-4644-865a-5aa25c91abfd/blobholder:0/2004LIMO0009.pdf.
Testo completoThe aim of this work was the elaboration and the characterization of electroconductive silicon nitride based ceramic composites Si3N4-TiN, Si3N4-TiB2 and Si3N4-HfB2, elaborated by Hot Isostatic Pressing (HIPing). A small amount of sintering aids (Y2O3, Al2O3) led to good densification and their high electrical conductivity authorized electrodischarge machining (EDM). The characterization of the materials was done by XRD, SEM and TEM analysis. Their mechanical properties (microhardness, fracture toughness, flexural strength at low and high temperatures) and the elastic moduli were analyzed. The oxidation resistance, studied under dynamic conditions in pure oxygen, between 900 and 1400ʿC, showed the better behavior of the Si3N4-HfB2 material. A multi-layered material was elaborated after the study of the wettability and reactivity with an Ag-Cu-Ti braze
Courbiere, Michel. "Etude des liaisons céramique-métal : Application au couple cuivre-alumine". Ecully, Ecole centrale de Lyon, 1986. http://www.theses.fr/1986ECDL0013.
Testo completoSerier, Boualem. "Etude et caractérisation des liaisons céramique-métal élaborées par thermocompression : application au couple Ag/Al2O3". Ecully, Ecole centrale de Lyon, 1991. http://www.theses.fr/1991ECDL0019.
Testo completoColin, Christophe. "Liaisons céramiques/métal à l'état solide par pressage uniaxial et par pressage isostatique". Paris, ENMP, 1991. http://www.theses.fr/1991ENMP0001.
Testo completoLoricourt, Johan. "Réalisation de liaisons céramique-métal par brasage dans une cellule prototype d’électrolyse de la vapeur d’eau à haute température pour la production d’hydrogène". Thesis, Montpellier 2, 2011. http://www.theses.fr/2011MON20037.
Testo completoSteam electrolysis at high temperature and under pressure with protonic conduction electrolyte is a way to produce hydrogen massively at low cost. To operate, an electrolysis cell must be hermetic especially between the anodic compartment (O2 and H2O) and the cathodic one (H2). Thus, ceramic to metal assemblies are needed, either to insert the electrolyte (perovskite-metal junction) or to realize power supply (alumina-metal junction).Considering the operating conditions (873°K, 725 PSI, steam), only a brazing process is possible to realize strong and hermetic junctions.The evaluation of corrosion process under steam pressure has enabled to select a metallic component and a brazing alloy for this application, and has shown that specific alloys are needed.The studies of ceramics metallization by PVD to assure the brazing alloy wetting throughout the brazing process have shown that a barrier diffusion was necessary to avoid the dissolution of coatings when the brazing alloy become liquid.After wetting experimentations of the chosen brazing alloy over the metalized ceramics and the metallic substrate, ceramic to metal assemblies have been optimized in applying the experimental design methodology on standard samples (ASTM).The whole results have enabled to develop hermetic ceramic to metal assemblies having good mechanical properties (Rm = 8700 PSI at 300°K)
Tahani, Abdelouahad. "Contribution à la détermination des phases formées à l'interface des liaisons céramo-métalliques : analyse de l'influence de la texture initiale du métal de base sur leurs orientations". Metz, 1993. http://docnum.univ-lorraine.fr/public/UPV-M/Theses/1993/Tahani.Abdelouahad.SMZ931.pdf.
Testo completoThis works represent the contribution of the analysis of the interactions physico-chemicals, which is developing in the binding interfaces of the ceramic-metal, at the time of realization of assembling according to the techniques of metal brazing directly reactive under vacum and thermocompression. We try to evalute the influence of the initial texture of the basic metal on the morphology and the orientation of the compounds or phases formed in the interface between the basic metal and the connection metal. Investigation methodology microanalytical is presented. The aim is to define the nature of the phases or formed compounds, and the orientation relations in the basic metal interface with the connection metal. Some phases are explained as a function of the binding and the heat treatment after assembling
Carrado, Adele. "Contribution à la caractérisation des propriétés mécaniques et microstructurales des liaisons céramique-métal utilisées pour les applications des matériaux dentaires". Phd thesis, Université de Reims - Champagne Ardenne, 2001. http://tel.archives-ouvertes.fr/tel-00229712.
Testo completoPlusieurs couches de porcelaine sont déposées sur un métal élaboré par moulage. Le coefficient de dilatation thermique de ces porcelaines doit être le plus proche possible de celui de l'alliage. La température de fusion de l ‘alliage doit, de plus, être supérieure à celle de la céramique pour réussir l'opération.
Cette étude porte sur l'évaluation du comportement mécanique à l'interface d'une céramique déposée sur un substrat d'alliage de palladium. Une caractérisation microstructurale et l'évaluation des contraintes résiduelles ont été menées sur différentes couches de l'échantillon. Des évaluations de contraintes ont été réalisées par diffraction neutronique et par rayonnement synchrotron à haute énergie pour caractériser l'état mécanique de l'échantillon. En effet, les propriétés mécaniques des couches métalliques dépendent grandement des contraintes résiduelles induites par l'application du revêtement. Il est alors essentiel de caractériser ces contraintes. Nous présentons ici les aspects généraux de l'évaluation des contraintes résiduelles, un modèle micro-mécanique appliqué dans notre étude et un bref calcul théorique.
Des mesures par diffraction ont été réalisées dans différentes zones de l'échantillon. En particulier, nous avons employé la diffraction neutronique pour analyser la surface et l'épaisseur de la céramique vitreuse et le
coeur du substrat métallique, et le rayonnement synchrotron à haute énergie pour étudier l'interface céramique - métal. De cette façon, nous avons obtenu les meilleures informations sur les différentes régions de l'échantillon analysé.
Pour ces techniques expérimentales, les mesures conduites aux interfaces entre deux différents matériaux sont très difficiles à analyser à cause des déplacements parasites importants du pic de diffraction qui existent dans ces conditions. Ces déplacements ne sont pas liés à l'état de contraintes du volume balayé et peuvent être plus importants que les effets induits par les contraintes. Nous avons développé, pour résoudre ce problème, une modélisation complète des spectromètres 2-axes, basée sur une simulation de type Monte Carlo. Cette modélisation est effectuée à la fois pour les spectromètres de neutrons, et pour les installations utilisant le rayonnement de synchrotron. Elle permet d'optimiser les conditions expérimentales et de définir précisément la taille et la position du volume sonde.
La microstructure de la céramique dentaire et de l'alliage de palladium a été enfin étudiée en utilisant la diffraction des rayons X (DXR), la Microscopie Electronique à Balayage (MEB) et la Spectrométrie à Dispersion d'Energie (EDS). La Microscopie Electronique à Transmission (TEM) à été aussi employée pour étudier les propriétés structurales des matériaux.
Carradó, Adèle. "Contribution à la caractérisation des propriétés mécaniques et microstructurales des liaisons céramique-métal utilisées pour les applications des matériaux dentaires". Reims, 2001. http://www.theses.fr/2001REIMS031.
Testo completoMagro, Christophe. "Céramiques supraconductrices de YBa₂Cu₃O₇-δ : étude de leur réactivité chimique et mise en évidence de mécanismes de texturation en liaison avec le courant critique". Bordeaux 1, 1992. http://www.theses.fr/1992BOR10661.
Testo completoObtaining high critical current densities in YBa₂Cu₃O₇-δ ceramics requires a mastery of their microstructure and composition. We have established correlations between processing conditions (influence carbonates and additions BaCuO2-CuO), chemical treatment (oxidation assisted by an electric current, by fluorination gas and plasma channel) and the superconducting characteristics of these materials. .
Fenard, Emmanuelle. "Céramiques composites du système Ti/B/N : Propriétés mécaniques et résistance à la corrosion". Limoges, 2001. http://www.theses.fr/2001LIMO0029.
Testo completoRoux, Philippe. "Rôle de la liaison silicium-hydrogène dans la thermolyse de polymères précurseurs de céramiques à base de carbure, de carbonitrure et de borocarbure de silicium". Bordeaux 1, 1993. http://www.theses.fr/1993BOR10650.
Testo completoHornebecq, Virginie. "Nouveaux tantalates ferroélectriques de type bronze quadratique de tungstène : de la structure aux propriétés physiques". Phd thesis, Université Sciences et Technologies - Bordeaux I, 2000. http://tel.archives-ouvertes.fr/tel-00003498.
Testo completoCazajus, Vincent. "Approches numérique et expérimentale de la liaison céramique métal réalisée par brasage en vue de la création d’un outil d’aide à la conception". Phd thesis, 2007. http://oatao.univ-toulouse.fr/7103/1/cazajus.pdf.
Testo completo