Letteratura scientifica selezionata sul tema "Hard superalloys"
Cita una fonte nei formati APA, MLA, Chicago, Harvard e in molti altri stili
Consulta la lista di attuali articoli, libri, tesi, atti di convegni e altre fonti scientifiche attinenti al tema "Hard superalloys".
Accanto a ogni fonte nell'elenco di riferimenti c'è un pulsante "Aggiungi alla bibliografia". Premilo e genereremo automaticamente la citazione bibliografica dell'opera scelta nello stile citazionale di cui hai bisogno: APA, MLA, Harvard, Chicago, Vancouver ecc.
Puoi anche scaricare il testo completo della pubblicazione scientifica nel formato .pdf e leggere online l'abstract (il sommario) dell'opera se è presente nei metadati.
Articoli di riviste sul tema "Hard superalloys":
Kursuncu, Bilal, Halil Caliskan, Sevki Yilmaz Guven e Peter Panjan. "Wear Behavior of Multilayer Nanocomposite TiAlSiN/TiSiN/TiAlN Coated Carbide Cutting Tool during Face Milling of Inconel 718 Superalloy". Journal of Nano Research 47 (maggio 2017): 11–16. http://dx.doi.org/10.4028/www.scientific.net/jnanor.47.11.
Pan, Lei, ZR Wu, Lei Fang e YD Song. "Investigation of surface damage and roughness for nickel-based superalloy GH4169 under hard turning processing". Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture 234, n. 4 (16 novembre 2019): 679–91. http://dx.doi.org/10.1177/0954405419885789.
Prasad, Ganesha, Raghavendra Kamath C. e Vijay G.S. "A review on conventional and nonconventional machining of Nickel-based Nimonic superalloy". Manufacturing Review 10 (2023): 10. http://dx.doi.org/10.1051/mfreview/2023009.
Zahedi, Ali, e J. Akbari. "FEM Analysis of Single Grit Chip Formation in Creep-Feed Grinding of Inconel 718 Superalloy". Advanced Materials Research 325 (agosto 2011): 128–33. http://dx.doi.org/10.4028/www.scientific.net/amr.325.128.
Díaz-Álvarez, José, Antonio Díaz-Álvarez, Henar Miguélez e José Cantero. "Finishing Turning of Ni Superalloy Haynes 282". Metals 8, n. 10 (18 ottobre 2018): 843. http://dx.doi.org/10.3390/met8100843.
Mukhtarov, Shamil, Artem Ganeev, Marsel Nagimov, Ruslan Shakhov, Vener Valitov e Farid Utyashev. "Manufacturing of Axisymmetric Components out of Superalloys and Hard-to-Deform Steels by Roll Forming". Key Engineering Materials 746 (luglio 2017): 69–74. http://dx.doi.org/10.4028/www.scientific.net/kem.746.69.
ALTIN, Abdullah. "Determination of Cutting Tool Performance Characteristics in Machining Nickel Based Super Alloys". International Conference on Applied Engineering and Natural Sciences 1, n. 1 (20 luglio 2023): 416–20. http://dx.doi.org/10.59287/icaens.1031.
Jean, Ming-Der, Shu-Yi Tu e Jen-Ting Wang. "Analysis of Hard-Facing Appearance of Specific Powdered Superalloys for PTA-Coating Processes". Journal of Materials Engineering and Performance 14, n. 3 (1 giugno 2005): 307–14. http://dx.doi.org/10.1361/10599490523904.
Díaz-Álvarez, Antonio, José Díaz-Álvarez, José Luis Cantero e Henar Miguélez. "Sustainable High-Speed Finishing Turning of Haynes 282 Using Carbide Tools in Dry Conditions". Metals 9, n. 9 (6 settembre 2019): 989. http://dx.doi.org/10.3390/met9090989.
Li, Yuebing, Yanming He, Chuanyang Lu, Wenjian Zheng, Jianguo Yang, Donghong Wang, Limei Wang, Yuan Sun e Zengliang Gao. "Microstructural Evolution and Mechanical Evaluation of a Laser-Induced Composite Coating on a Ni-Based Superalloy during Thermal Exposure". Materials 12, n. 9 (3 maggio 2019): 1439. http://dx.doi.org/10.3390/ma12091439.
Tesi sul tema "Hard superalloys":
Karamched, Phani Shashanka. "Deformation studies near hard particles in a superalloy". Thesis, University of Oxford, 2011. http://ora.ox.ac.uk/objects/uuid:e740592d-8d82-4c12-9bfe-99901d132b60.
SIVO, ANTONIO. "On the Laser Powder Bed Fusion based processing route for hard to weld Nickel Superalloys". Doctoral thesis, Politecnico di Torino, 2022. http://hdl.handle.net/11583/2971609.
Agode, Kofi Edoh. "Analyse et modélisation du comportement à l’usure des outils de coupe en carbure de tungstène pour différentes teneurs en cobalt lors de l’usinage de l’alliage de titane Ti-6Al-4V". Electronic Thesis or Diss., Université de Lorraine, 2022. http://www.theses.fr/2022LORR0141.
Due to their high hardness and wear resistance, cemented carbide (WC-Co) is the main material used to manufacture machining tools and forming tooling, as well as wear parts requiring high hardness and high precision. The modification of tungsten carbide microstructure, and more particularly its cobalt content, is currently attracting the greatest interest from manufacturers to develop new grades tools with high performance, and then expand new markets.This thesis aims to study the effect of the cobalt content of carbide tools on the measured values and wear mechanisms when machining hard superalloys such as the aeronautical titanium alloys Ti-6Al-4V. Both experimental and numerical research work are devoted on one hand to the understanding of the microscopic damage mechanisms leading to the macroscopic wear of the WC-Co composite and on the other hand, to the influence of the cobalt content on the behavior of the WC-Co taking into account the mechanical-microstructure-damage coupling.On the basis of an experimental analysis, the identification of the macroscopic and microscopic physical phenomena involved at the tool/chip and tool/workpiece contact interfaces was conducted. Machining tests were firstly carried out on the tool-material couple WC-Co/Ti-6Al-4V with different cobalt contents for the tools (from 6 to 15%). In a second step, a tribological characterization of the same tool-material couple was carried out to evaluate the influence of the cobalt content and the contact conditions (sliding speed, applied force) on the friction coefficient and wear. However, the inaccessibility of the contact zones during machining and the tribological tests did not allow a complete description of the wear mechanisms observed, whether macroscopic mechanisms (adhesion, abrasion, deformation, ...), or microscopic mechanisms (cracking, damage of the WC and Co phases). The numerical simulation using finite elements (FE) proved to be a very interesting complementary tool for the analysis of these wear mechanisms.Our modeling strategy focused on the response of WC-Co at the microstructure scale for the thermomechanical loading close to that obtained by machining. The proposed model takes into account the behavior of the WC and Co phases separately and that of the interfaces WC-WC and WC-Co of the composite. This strategy allowed to study and identify parameters influencing the behavior of the microstructure from the elastic stage to the damage initiation. A good agreement was obtained between the results of the numerical behavior at the initiation of damage in the microstructure and those of the experimental observations in terms of the effects of the cobalt content in the tungsten carbide and of the applied machining conditions
Capitoli di libri sul tema "Hard superalloys":
Casteletti, L. C., A. Lombardi Neto, D. T. de Macedo, L. B. Cruvinel e George Totten. "Stellite Superalloy Powder Deposition on 7075 Aluminum Alloy". In Encyclopedia of Aluminum and Its Alloys. Boca Raton: CRC Press, 2019. http://dx.doi.org/10.1201/9781351045636-140000303.
Hall, Christopher. "5. Making stuff and making things". In Materials: A Very Short Introduction, 83–101. Oxford University Press, 2014. http://dx.doi.org/10.1093/actrade/9780199672677.003.0005.
Atti di convegni sul tema "Hard superalloys":
Ratay, Jason, e Hitomi Yamaguchi. "Characteristics of Diamond Abrasive Used in Magnetic Abrasive Finishing of Nickel-Based Superalloys". In ASME 2020 15th International Manufacturing Science and Engineering Conference. American Society of Mechanical Engineers, 2020. http://dx.doi.org/10.1115/msec2020-8365.
Branagan, D. J., M. C. Marshall, B. E. Meacham, L. F. Aprigliano, R. Bayles, E. J. Lemieux, T. Newbauer et al. "Wear and Corrosion Resistant Amorphous / Nanostructured Steel Coatings For Replacement of Electrolytic Hard Chromium". In ITSC2006, a cura di B. R. Marple, M. M. Hyland, Y. C. Lau, R. S. Lima e J. Voyer. ASM International, 2006. http://dx.doi.org/10.31399/asm.cp.itsc2006p0733.
Rajesh Jha, George Stavo Dulikravich e Marcelo Jose Colaco. "Design and optimization of rare-earth free hard magnetic alloys and Nickel-based superalloys for high temperature applications". In 23rd ABCM International Congress of Mechanical Engineering. Rio de Janeiro, Brazil: ABCM Brazilian Society of Mechanical Sciences and Engineering, 2015. http://dx.doi.org/10.20906/cps/cob-2015-1284.
Pasupuleti, Thejasree, Manikandan Natarajan, Loganayagan Shanmugam, Jothi Kiruthika, Mude Ramesh Naik e Gowthami Kotapati. "Application of Taguchi Based ANFIS Approach in Wire Electrical Discharge Machining of Inconel 625 for Automobile Applications". In International Conference on Advances in Design, Materials, Manufacturing and Surface Engineering for Mobility. 400 Commonwealth Drive, Warrendale, PA, United States: SAE International, 2023. http://dx.doi.org/10.4271/2023-28-0148.
Natarajan, Manikandan, Thejasree Pasupuleti, Gnana Sagaya Raj, V. Kumar, Lakshmi Narasimhamu Katta e Jothi Kiruthika. "Machinability Studies and the Evolution of Hybrid Artificial Intelligent Tools for Advanced Machining of Nickel Alloy for Aerospace Applications". In International Conference on Advances in Design, Materials, Manufacturing and Surface Engineering for Mobility. 400 Commonwealth Drive, Warrendale, PA, United States: SAE International, 2023. http://dx.doi.org/10.4271/2023-28-0065.
Ogata, Takashi, e Takayuki Sakai. "Life Prediction Method of CC and DS Ni Base Superalloys Under High Temperature Biaxial Fatigue Loading". In ASME Turbo Expo 2009: Power for Land, Sea, and Air. ASMEDC, 2009. http://dx.doi.org/10.1115/gt2009-59069.
Tapphorn, R., H. Gabel, K. Hashimoto e T. Crowe. "Kinetic Metallization of Interior Diameter Bores". In ITSC 2012, a cura di R. S. Lima, A. Agarwal, M. M. Hyland, Y. C. Lau, C. J. Li, A. McDonald e F. L. Toma. ASM International, 2012. http://dx.doi.org/10.31399/asm.cp.itsc2012p0311.
Li, Y. L., C. L. Ma e H. Zhang. "Crystallographic Orientation Evolution in NbSS-Nb5Si3 Eutectic Alloys by EBSD Analyses". In ASME Turbo Expo 2013: Turbine Technical Conference and Exposition. American Society of Mechanical Engineers, 2013. http://dx.doi.org/10.1115/gt2013-95309.
Li, Ji, Rongcan Zhou, Liying Tang, Bohan Wang, Shufang Hou, Jiang Li, Weiguo Liu, Hongyu Liu e Xiaomin Li. "Effect of Aging Heat-Treatment on the Creep Behavior of Inconel 740H Used in 700 °C A-USC Power Plants". In AM-EPRI 2019, a cura di J. Shingledecker e M. Takeyama. ASM International, 2019. http://dx.doi.org/10.31399/asm.cp.am-epri-2019p0448.
Pasupuleti, Thejasree, Manikandan Natarajan, V. Kumar, Lakshmi Narasimhamu Katta, Jothi Kiruthika e R. Silambarasan. "Predictive Modelling and Process Parameter Prediction for Monel 400 Wire Electrical Discharge Machining for Rocket Frames". In International Conference on Advances in Design, Materials, Manufacturing and Surface Engineering for Mobility. 400 Commonwealth Drive, Warrendale, PA, United States: SAE International, 2023. http://dx.doi.org/10.4271/2023-28-0088.