Bibliografie tematiche / Electroless plating / Articoli di riviste
Segui questo link per vedere altri tipi di pubblicazioni sul tema: Electroless plating.

Articoli di riviste sul tema "Electroless plating"

Autore: Grafiati
Pubblicato: 4 giugno 2021
Ultima modifica: 6 settembre 2023

Cita una fonte nei formati APA, MLA, Chicago, Harvard e in molti altri stili

Scegli il tipo di fonte:

Vedi i top-50 articoli di riviste per l'attività di ricerca sul tema "Electroless plating".

Accanto a ogni fonte nell'elenco di riferimenti c'è un pulsante "Aggiungi alla bibliografia". Premilo e genereremo automaticamente la citazione bibliografica dell'opera scelta nello stile citazionale di cui hai bisogno: APA, MLA, Harvard, Chicago, Vancouver ecc.

Puoi anche scaricare il testo completo della pubblicazione scientifica nel formato .pdf e leggere online l'abstract (il sommario) dell'opera se è presente nei metadati.

Vedi gli articoli di riviste di molte aree scientifiche e compila una bibliografia corretta.

1

SAITO, Mamoru. "Electroless Plating. Recent Trend of Electroless Plating." Journal of the Surface Finishing Society of Japan 48, n. 4 (1997): 375–79. http://dx.doi.org/10.4139/sfj.48.375.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
2

Sun, Hua, Xiao Fei Guo, Ke Gao Liu, Hong Fang Ma e Li Ming Feng. "Influence of Ultrasonic on the Microstructure and Properties of Electroless Plating Ni-Co-P Coating at Low Temperature". Advanced Materials Research 314-316 (agosto 2011): 259–62. http://dx.doi.org/10.4028/www.scientific.net/amr.314-316.259.

Testo completo
Abstract (sommario):
By electron energy spectrometer,X-ray diffractometer,transmission elec-tron microscopy andmicro-hardometer,the depositing speed of electrolessNi-Co-P plating baths,chemical composition,crystal structure and microhardness of the alloy coatings were inspected and analyzed with ultrasonic and rare earth metalcerium intervening in electroless Ni-Co-P plating•The results show that the depositing speed of electroless Ni-Co-P plating isobviously increased under the effect of ultrasonic.The chemical compositions of electroless Ni-Co-P plating are changed，The XRD of coating has a diffuse sexual diffraction peak closing to typical amorphous structure.the obtained Ni-Co-P coating has more fine crystal grain, even and dense surface morphology. Its wear resistance and hardness have been improved obviously.
Gli stili APA, Harvard, Vancouver, ISO e altri
3

HARADA, Hisashi. "Electroless Plating". Journal of the Japan Society of Colour Material 69, n. 1 (1996): 60–70. http://dx.doi.org/10.4011/shikizai1937.69.60.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
4

UCHIDA, Ei. "Electroless Plating. Electroless Palladium Plating and Its Applications." Journal of the Surface Finishing Society of Japan 48, n. 4 (1997): 400–404. http://dx.doi.org/10.4139/sfj.48.400.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
5

SAKATA, Takahiro, e Hideo HONMA. "Electroless copper plating by applying electrolysis." Journal of the Surface Finishing Society of Japan 40, n. 3 (1989): 488–89. http://dx.doi.org/10.4139/sfj.40.488.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
6

Uraz, Canan, e Tuğba Gürmen Özçelik. "ELECTROLESS METAL PLATING OVER ABS PLASTIC". E-journal of New World Sciences Academy 14, n. 2 (29 aprile 2019): 63–70. http://dx.doi.org/10.12739/nwsa.2019.14.2.1a0432.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
7

SHIBATA, Mitsuo. "Electroless Plating. Direct Electroless Nickel Plating on Magnesium Alloys." Journal of the Surface Finishing Society of Japan 48, n. 4 (1997): 413–16. http://dx.doi.org/10.4139/sfj.48.413.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
8

KAMIYAMA, Hiroharu. "Electroless copper plating." Circuit Technology 4, n. 6 (1989): 318–26. http://dx.doi.org/10.5104/jiep1986.4.318.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
9

HONMA, Hideo, Yasunori KOUCHI e Masaaki OYAMADA. "Electroless Solder Plating." Circuit Technology 6, n. 6 (1991): 299–305. http://dx.doi.org/10.5104/jiep1986.6.6_299.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
10

Brown, L. D. "Electroless nickel plating". International Materials Reviews 37, n. 1 (gennaio 1992): 196. http://dx.doi.org/10.1179/imr.1992.37.1.196.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
11

Brown, L. D. "‘Electroless nickel plating’". British Corrosion Journal 27, n. 1 (gennaio 1992): 25–26. http://dx.doi.org/10.1179/000705992798268882.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
12

Henry, James R. "Electroless (autocatalytic) plating". Metal Finishing 98, n. 1 (gennaio 2000): 424–35. http://dx.doi.org/10.1016/s0026-0576(00)80351-7.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
13

Henry, James R. "Electroless (autocatalytic) plating". Metal Finishing 97, n. 1 (gennaio 1999): 424–35. http://dx.doi.org/10.1016/s0026-0576(00)83102-5.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
14

Henry, James R. "Electroless (autocatalytic) plating". Metal Finishing 99 (gennaio 2001): 424–35. http://dx.doi.org/10.1016/s0026-0576(01)85302-2.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
15

Henry, James R. "Electroless (autocatalytic) plating". Metal Finishing 100 (gennaio 2002): 409–20. http://dx.doi.org/10.1016/s0026-0576(02)82044-x.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
16

Henry, James R. "Electroless (autocatalytic) plating". Metal Finishing 97, n. 1 (gennaio 1999): 431–42. http://dx.doi.org/10.1016/s0026-0576(99)80044-0.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
17

Baudrand, Don, e Jon Bengston. "Electroless plating processes". Metal Finishing 93, n. 9 (settembre 1995): 55–57. http://dx.doi.org/10.1016/0026-0576(95)99502-2.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
18

NAKAGISHI, Yutaka. "Electroless Plating. Functional Separation and Application of Electroless Nickel Plating." Journal of the Surface Finishing Society of Japan 48, n. 4 (1997): 380–86. http://dx.doi.org/10.4139/sfj.48.380.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
19

NISHIYAMA, Kouji, e Hideto WATANABE. "Electroless Plating. The Type and Application of Electroless Gold Plating." Journal of the Surface Finishing Society of Japan 48, n. 4 (1997): 393–99. http://dx.doi.org/10.4139/sfj.48.393.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
20

NITTA, Masahiro, e Hiroshi ADACHI. "Electroless Plating. Deep Black Electroless Nickel Plating-Phos Black II." Journal of the Surface Finishing Society of Japan 48, n. 4 (1997): 417–19. http://dx.doi.org/10.4139/sfj.48.417.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
21

Liu, Guan Jun, Xin Hua Mao, Jun Cao e Zhou Yu. "Effect of Heat Treatment on Hardness of Electroless Ni-P Plating". Advanced Materials Research 228-229 (aprile 2011): 878–82. http://dx.doi.org/10.4028/www.scientific.net/amr.228-229.878.

Testo completo
Abstract (sommario):
Hardness of electronless Ni-P alloy plating which have five different phosphorus content were investigated with HX-1000 type microscopic Vickers hardness tester, respectively. Phosphorus content of Ni-P platings were investigated by Quanta 200 type scanning electron microscope and Oxford Energy Disperse Spectroscopy Heat treatment temperature and time of the different platings were optimized and analysed by Uniform Design method, respectively. The results show that correlation consist between maximum hardness of the Ni-P alloy plating and heat treatment temperature, not heat treatment time under the experimental condition which the heat treatment time is between one hour and five hours, and maximal value of the plating hardness appears when the heat treatment temperature is 400-430 Celsius degree. Maximal hardness value of the electronless Ni-P alloy plating increases with increase of their phosphorus content under heat treatment condition.
Gli stili APA, Harvard, Vancouver, ISO e altri
22

Liu, Yan Ping, Yan Mei Zhang, Yuan Gao e Zhong Xu. "The Influence of Impulse Electroless Plating on Amorphous Ni-P Alloys in Structure and Hot Stability". Materials Science Forum 475-479 (gennaio 2005): 3989–92. http://dx.doi.org/10.4028/www.scientific.net/msf.475-479.3989.

Testo completo
Abstract (sommario):
Using a special impulse device, the impulse electroless Ni-P alloy plating were prepared. The microstructure、crystallization and the starting activation energy for crystallization was investigated by TEM、XRD and DTA, compared with electroless Ni-P alloys plating. The results showed that the diffractive ring was wider when using impulse, depositing temperature dropped up to 65°C,and crystallization temperature rose up to 310°C. Furthermore , the starting activation energy for crystallization and crystallization temperature of impulse electroless Ni-P alloys plating measured were more than that of electroless plating in the heating rate at 5、10、20、 40K/min, and it was also higher in the amorphous disorder degree and the starting crystallization temperature. Impulse electroless Ni-P alloys plating had better performance of thermal stability.
Gli stili APA, Harvard, Vancouver, ISO e altri
23

FUJINAMI, Tomoyuki. "Electroless Plating. Various Functional Applications of Formalin-Free Electroless Copper Plating." Journal of the Surface Finishing Society of Japan 48, n. 4 (1997): 387–92. http://dx.doi.org/10.4139/sfj.48.387.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
24

Wanping, Chen, Li Longtu e Gui Zhilun. "Effects of Electroless Nickel Plating on Resistivity-temperature Characteristics of (Ba1-xPbx)TiO3thermistor". Journal of Materials Research 12, n. 4 (aprile 1997): 877–79. http://dx.doi.org/10.1557/jmr.1997.0127.

Testo completo
Abstract (sommario):
Effects of electroless nickel plating on resistivity-temperature (R-T) characteristics of (Ba1-xPbx)TiO3 thermistor were studied. Comparison experiments showed that not only the permeation of plating solution, but also the reaction of electroless nickel plating influences the positive temperature coefficient (PTC) effect, and that the two effects are different in nature. It is first proposed in this paper that hydrogen atoms generated in electroless nickel plating may reduce components of PTC ceramics.
Gli stili APA, Harvard, Vancouver, ISO e altri
25

Feng, Li Ming, e Xue Wei. "On the Dispersants of Diamond-Ni-P Composite Electroless Plating and Properties of the Coating". Advanced Materials Research 189-193 (febbraio 2011): 181–85. http://dx.doi.org/10.4028/www.scientific.net/amr.189-193.181.

Testo completo
Abstract (sommario):
In order to obtain stable and homogeneous diamond-Ni-P composite electroless plating, dispersants were selected by determining the height of emulsion in the colorimetric cylinder after standing different time.The structure,elemental contents and properties of the diamond-Ni-P composite electroless plating coating were investigated by SEM and EDS. Experimental results show that OP-10 of 50mL•L-1 and softex kw of 1g•L-1 have better dispersing effect to diamond powder of 1g•L-1 in water. This composite electroless plating solution can keep stable for more than twelve or eight hours respectively at 85°C. While in the electroless plating solution, Softex kw of 1g•L-1 has better dispersing effect and can be stable for more than two hours at 85°C. The diamond powder grains in the composite coating are homogeneous and the content of carbon is 2.261 wt% under the certain amount of the selected dispersant. When the content of diamond was 5g•L-1 in the solution, the diamond powders were dispersed non-homogeneously in plating and cluster phenomena were appeared. The composite electroless plating coating consists of amorphous Ni-P and diamond powder. Its hardness and porosity are similar to those of the electroless plating Ni-P coating. The wear-resisting is improved greatly,which is 2.6 times of electroless plating Ni-P or 2 times of that after heat treatment at 400°C for one hour.
Gli stili APA, Harvard, Vancouver, ISO e altri
26

ZHAO, YAN, RUN ZHANG, TONG ZHANG e YUEXIN DUAN. "EFFECT OF DIFFERENT PRETREATMENTS TO ELECTROLESS NICKEL OR COBALT PLATING ON HOLLOW MICROSPHERES". International Journal of Modern Physics B 24, n. 15n16 (30 giugno 2010): 2706–11. http://dx.doi.org/10.1142/s0217979210065507.

Testo completo
Abstract (sommario):
Different pretreatment methods for electroless nickel and cobalt plating are demonstrated and compared in the present investigation. The surface morphologies of the nickel or cobalt deposits are investigated by scanning electron microscopy (SEM), and the chemical compositions of the coatings are analyzed by energy-dispersive X-ray spectroscopy (EDX). Method of single-step pretreatment is selected as the optimized method for electroless nickel plating process, while improved two-step sensitization-activation and single-step pretreatment methods can be selected for electroless cobalt plating. It can be found that the content of free Co is much lower compared to electroless Ni plating.
Gli stili APA, Harvard, Vancouver, ISO e altri
27

Dervos, C. T., P. Vassiliou e J. Novakovic. "Electroless Ni-B plating for electrical contact applications". Revista de Metalurgia 41, Extra (17 dicembre 2005): 232–38. http://dx.doi.org/10.3989/revmetalm.2005.v41.iextra.1031.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
28

URAZ, Canan. "Effect of Room Temperature Ionic Liquids for Electroless Nickel Plating on Acrylonitrile Butadiene Styrene Plastic". Materials Science 25, n. 3 (10 maggio 2019): 276–80. http://dx.doi.org/10.5755/j01.ms.25.3.20116.

Testo completo
Abstract (sommario):
In this study, electroless nickel (EN) plating on acrylonitrile butadiene styrene (ABS) engineering plastic using room temperature ionic liquids (RTIL) was studied. Electroless plating is a fundamental step in metal plating on plastic. This step makes the plastic conductive and makes it possible to a homogeneous and hard plating without using any hazardous and unfriendly chemical such as palladium, tin, etc. In the industry there are many distinct chemical materials both catalysts and activation solutions for the electroless bath which is one of the most important parts of the process. In this study the effects of the ionic liquid, plating time, and sand paper size were investigated on electroless nickel plating. The etching and the plating processes were performed with environmentally friendly chemicals instead of the chromic and sulphuric acids used in the traditional processes. Experiments were carried out with and without ionic liquid, EMIC, 1-ethyl-3-methyl imidazolium chloride (C6H11N2Cl), and with 400, 500 and 800 grit sandpaper with the application of the sand attrition process and 70, 80, and 90 °C bath temperatures with 30, 60, and 90 minutes of deposition time. The surface morphology and the thickness of deposit analysis were performed using the Fischer scope X-Ray XDL-B System, X-ray Diffraction (XRD), and Scanning Electron Microscopy (SEM). Due to the results of the experiments and analysis, the electroless nickel plating on ABS plastic was a success. The best plating was obtained at 5.010 μm as the maximum plating thickness, at 90 min of plating time and 80 °C as the plating bath temperature for electroless nickel plating on ABS plastic whit the surface activated with 800 grit sandpaper using EMIC ionic liquid. DOI: http://dx.doi.org/10.5755/j01.ms.25.3.20116
Gli stili APA, Harvard, Vancouver, ISO e altri
29

Wu, Ming Ming, e Bai Yang Lou. "Preparation and Corrosion Resistance of Electroless Plating of Ni-Cr-P/Ni-P Composite Coating on Sintered Nd-Fe-B Permanent Magnet". Advanced Materials Research 284-286 (luglio 2011): 2187–90. http://dx.doi.org/10.4028/www.scientific.net/amr.284-286.2187.

Testo completo
Abstract (sommario):
This paper introduces electroless plating Ni-Cr-P/Ni-P composite coating technologies and techniques on the Nd-Fe-B permanent magnet surface. It has got a Ni-Cr-P/Ni-P composite coating successfully on the Nd-Fe-B substrate surface through rational processing plan. The coating surfaces are bright and have low Porosity, good binding between the electroless plating and Nd-Fe-B matrix. The experimental results show that the composite coating prepared by Ni-Cr-P electroless plating (15min) and Ni-P acidic electroless plating (45min) has amorphous structure, simple process and better anticorrosion property in both alkaline and acidic medium.
Gli stili APA, Harvard, Vancouver, ISO e altri
30

KOBAYASHI, Michio, e Tadashi IIMORI. "Electroless plating on titanium." Jitsumu Hyomen Gijutsu 35, n. 6 (1988): 312–18. http://dx.doi.org/10.4139/sfj1970.35.312.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
31

KOURA, Nobuyuki, e Atsushi KUBOTA. "Electroless plating of silver." Journal of the Metal Finishing Society of Japan 36, n. 5 (1985): 182–90. http://dx.doi.org/10.4139/sfj1950.36.182.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
32

NAKAZATO, Junichi, Kei HASHIZUME e Toru MORIMOTO. "Black Electroless Ni Plating". Journal of the Surface Finishing Society of Japan 66, n. 11 (2015): 503–6. http://dx.doi.org/10.4139/sfj.66.503.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
33

WATANABE, Hideto. "Electroless Precious Metal Plating". Journal of The Surface Finishing Society of Japan 70, n. 9 (1 settembre 2019): 435–40. http://dx.doi.org/10.4139/sfj.70.435.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
34

NAKAO, YUKIMICHI. "Electroless Plating of Paper". Sen'i Gakkaishi 42, n. 12 (1986): P510—P514. http://dx.doi.org/10.2115/fiber.42.12_p510.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
35

Ohtsuka, Kuniaki, Kazuyoshi Okuno, Noriko Hattori e Eiichi Torikai. "Electroless Gold Plating Solution". Transactions of the IMF 69, n. 1 (gennaio 1991): 33–36. http://dx.doi.org/10.1080/00202967.1991.11870888.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
36

Ohno, Izumi. "Electrochemistry of electroless plating". Materials Science and Engineering: A 146, n. 1-2 (ottobre 1991): 33–49. http://dx.doi.org/10.1016/0921-5093(91)90266-p.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
37

"Electroless plating apparatus and electroless plating method". Metal Finishing 103, n. 6 (giugno 2005): 67–68. http://dx.doi.org/10.1016/s0026-0576(05)80105-9.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
38

"Electroless plating solution". Metal Finishing 98, n. 2 (febbraio 2000): 119. http://dx.doi.org/10.1016/s0026-0576(00)81463-4.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
39

"Electroless plating process". Metal Finishing 98, n. 5 (maggio 2000): 93–94. http://dx.doi.org/10.1016/s0026-0576(00)81789-4.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
40

"Electroless nickel plating". Metal Finishing 98, n. 7 (luglio 2000): 71–72. http://dx.doi.org/10.1016/s0026-0576(00)82397-1.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
41

"Monitoring electroless plating". Metal Finishing 98, n. 11 (novembre 2000): 109–10. http://dx.doi.org/10.1016/s0026-0576(00)83673-9.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
42

"Electroless plating process". Metal Finishing 97, n. 6 (giugno 1999): 172. http://dx.doi.org/10.1016/s0026-0576(00)84033-7.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
43

"Electroless copper plating". Metal Finishing 97, n. 8 (agosto 1999): 77–78. http://dx.doi.org/10.1016/s0026-0576(01)80190-2.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
44

"Electroless plating process". Metal Finishing 99, n. 5 (maggio 2001): 86. http://dx.doi.org/10.1016/s0026-0576(01)80884-9.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
45

"Electroless plating process". Metal Finishing 99, n. 5 (maggio 2001): 88. http://dx.doi.org/10.1016/s0026-0576(01)80894-1.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
46

"Electroless plating method". Metal Finishing 99, n. 7 (luglio 2001): 76. http://dx.doi.org/10.1016/s0026-0576(01)81164-8.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
47

"Electroless plating process". Metal Finishing 94, n. 11 (novembre 1996): 120. http://dx.doi.org/10.1016/s0026-0576(96)92782-8.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
48

"Electroless plating process". Metal Finishing 100, n. 6 (giugno 2002): 158. http://dx.doi.org/10.1016/s0026-0576(02)80539-6.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
49

"Electroless nickel plating". Metal Finishing 101, n. 3 (marzo 2003): 34. http://dx.doi.org/10.1016/s0026-0576(03)80267-2.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
50

"Electroless plating bath". Metal Finishing 95, n. 6 (giugno 1997): 168–69. http://dx.doi.org/10.1016/s0026-0576(97)89134-9.

Testo completo
Gli stili APA, Harvard, Vancouver, ISO e altri
Ti possono interessare anche gli elenchi di altri tipi di fonti sul tema "Electroless plating":
Tesi Libri
Offriamo sconti su tutti i piani premium per gli autori le cui opere sono incluse in raccolte letterarie tematiche. Contattaci per ottenere un codice promozionale unico!

Vai alla bibliografia