Articoli di riviste: "Acoustical engineering"

1

Burkhard, Mahlon D. "Acoustical standards in engineering acoustics". Journal of the Acoustical Society of America 115, n. 5 (maggio 2004): 2434. http://dx.doi.org/10.1121/1.4781590.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

2

Haberman, Michael R. "Introduction to the Technical Committee on Engineering Acoustics". Journal of the Acoustical Society of America 155, n. 3_Supplement (1 marzo 2024): A29. http://dx.doi.org/10.1121/10.0026675.

Testo completo

Abstract (sommario):

This talk will introduce ongoing work in the Technical Committee on Engineering Acoustics (TCEA) of the Acoustical Society of America. Engineering Acoustics encompasses the theory and practice of creating tools to generate and investigate acoustical phenomena and then to apply the knowledge of acoustics to practical utility. This includes the design and modeling of acoustical and vibrational transducers, transducer arrays, and transduction materials or systems in all media and frequency ranges. It is also concerned with the design of acoustical instrumentation, metrology, and the calibration of those systems. It further considers all aspects of measurement, fabrication, and computational techniques as they relate to acoustical phenomena and their utility. The talk will provide an introduction of a broad range of research topics in TCEA, with specific highlights on exciting new areas of research.

Gli stili APA, Harvard, Vancouver, ISO e altri

3

Molevich, Nonna E., Anatoly I. Klimov e Vladimir G. Makaryan. "Influence of Thermodynamic Nonequilibrium on the Acoustic Properties of Gases". International Journal of Aeroacoustics 4, n. 3 (luglio 2005): 373–83. http://dx.doi.org/10.1260/1475472054771411.

Testo completo

Abstract (sommario):

This paper is a brief review of results of experimental and theoretical studies in the field of acoustics of nonequilibrium gas-plasma media. New acoustical properties of nonequilibrium media caused by the change in sign of the second viscosity and the dispersion coefficients are considered. Such media are acoustically active. Conditions are discussed for generating new nonlinear acoustical structures.

Gli stili APA, Harvard, Vancouver, ISO e altri

4

Van Uffelen, Lora, James H. Miller e Gopu R. Potty. "Underwater acoustics and ocean engineering at the University of Rhode Island". Journal of the Acoustical Society of America 152, n. 4 (ottobre 2022): A124. http://dx.doi.org/10.1121/10.0015761.

Testo completo

Abstract (sommario):

Underwater acoustics is one of the primary areas of emphasis in the Ocean Engineering Department at the University of Rhode Island, the first Ocean Engineering program in the United States. The program offers Bachelors, Masters (thesis and non-thesis options) and PhD degrees in Ocean Engineering. These programs are based at the Narragansett Bay campus, providing access to a living laboratory for student learning. Some key facilities of the program are an acoustics tank and a 100-foot-long wave tank. At the graduate level, students are actively involved in research focused in areas such as acoustical oceanography, propagation modeling, geoacoustic inversion, marine mammal acoustics, ocean acoustic instrumentation, and transducers. An overview of classroom learning and ongoing research will be provided, along with information regarding the requirements of entry into the program.

Gli stili APA, Harvard, Vancouver, ISO e altri

5

Brown, David A., Paul J. Gendron e John R. Buck. "Graduate education in acoustic engineering, transduction, and signal processing University of Massachusetts Dartmouth". Journal of the Acoustical Society of America 152, n. 4 (ottobre 2022): A123. http://dx.doi.org/10.1121/10.0015756.

Testo completo

Abstract (sommario):

The University of Massachusetts Dartmouth has an established graduate program of study with a concentration in Applied Acoustics leading to the M.S. and Ph.D. degree in Electrical Engineering. The program offers courses and research opportunities in the area of electroacoustic transduction, underwater acoustics, and signal processing. Courses include the Fundamentals of Acoustics, Random Signals, Underwater Acoustics, Introduction to Transducers, Electroacoustic Transduction, Medical Ultrasonics, Digital Signal Processing, Detection Theory, and Estimation Theory. The ECE department established the university’s indoor underwater acoustic test and calibration facility which is one of the largest academic facilities supporting undergraduate and graduate thesis and sponsored research. The department has collaborations with many marine acoustic related companies including nearby Naval Undersea Warfare Center in Newport, RI and Woods Hole Oceanographic Institute in Cape Cod, MA. The presentation will highlight recent theses and dissertations, course offerings, and industry and government collaborations that support acoustical engineering, transduction, and signal processing.

Gli stili APA, Harvard, Vancouver, ISO e altri

6

Fonseca, William D'Andrea, Eric Brandão, Paulo H. Mareze, Viviane S. G. Melo, Roberto A. Tenenbaum, Christian dos Santos e Dinara Paixão. "Acoustical engineering: A complete academic undergraduate program in Brazil". Journal of the Acoustical Society of America 152, n. 2 (agosto 2022): 1180–91. http://dx.doi.org/10.1121/10.0013570.

Testo completo

Abstract (sommario):

Acoustics is a broad field of knowledge that extends branches all over the physics of wave phenomena, psychology, natural sciences, and engineering. It is taught, in general, as part of engineering, physics, or architecture programs, or even in graduate programs specialized in the theme. In Brazil, acoustics was taught in graduate programs, until the creation of Acoustical Engineering in 2009, at the Federal University of Santa Maria, an integral undergraduate program dedicated to acoustics, audio, and vibration (lasting ten semesters). This article presents its complete academic program, its creation process, and the professional establishment of the acoustical engineer. In the following, the program of study and subjects are elucidated and detailed, and the teaching methodologies used are also discussed. The program employs several active learning strategies, like project-based learning, aiming to transform abstract into concrete knowledge. The interaction of the university, the acoustical engineer, and society is also presented and clarified. The placement of graduates in fields and their workplaces are presented as outcomes. As a fundamental part of the engineer's formation, the infrastructure used, whether state-of-the-art or cost-effective equipment, is detailed in the context of teaching and research. Finally, some of the ongoing research projects of the students are described.

Gli stili APA, Harvard, Vancouver, ISO e altri

7

Hioka, Yusuke, Michael Kingan e George Dodd. "Learning effect of active learning coursework in engineering acoustics course". INTER-NOISE and NOISE-CON Congress and Conference Proceedings 263, n. 2 (1 agosto 2021): 4154–65. http://dx.doi.org/10.3397/in-2021-2617.

Testo completo

Abstract (sommario):

This paper reports the learning effect achieved by a newly developed coursework for an engineering acoustics course offered to fourth year and postgraduate engineering students at the University of Auckland, New Zealand. The course teaches fundamental knowledge that acoustical engineers need and which underpins a variety of sub-disciplines in acoustics including: fundamental physics of wave propagation, building and room acoustics, electro-acoustics, audio signal processing, and the psychology of hearing. The coursework incorporated practical active learning activities and was developed in order to help students gain understanding of complex concepts related to the room acoustics measurement and analysis. The coursework also has the goal of providing students with an introduction to some of the practical tasks which are typical of a practising acoustical engineering in New Zealand. The learning effect was measured by comparing students' performance in a quiz that was run before students commenced working on the coursework and that in the final examination and by investigating common mistakes students made in the report which was the required deliverable of the coursework. Overall, the new coursework successfully improved students' understanding of the material which it covered.

Gli stili APA, Harvard, Vancouver, ISO e altri

8

Boot, Tim, Frederic Roskam, Phil Coleman, Simon Brown e Julien Laval. "Greater artistic and technological performance through the converged technologies of architectural acoustics, electroacoustic enhancement, and immersive audio technologies". Journal of the Acoustical Society of America 154, n. 4_supplement (1 ottobre 2023): A168. http://dx.doi.org/10.1121/10.0023155.

Testo completo

Abstract (sommario):

Producing meaningful, creative, and engaging experiences for audiences requires highly integrated acoustics and audio technologies. The fields of architectural acoustics, electro acoustic enhancement and immersive audio technologies have converged, altering the way we approach entertainment venue design. Globally, demand has increased for immersive audio in live and reproduced sound, and electro acoustic enhancement technologies are becoming more widespread. We will discuss how architecturally integrated end devices, multi-function signal processing, and architectural acoustical design should be optimized to create next-generation performance venues. We will use a project example that integrates sound system, acoustic enhancement, and architectural acoustics, illustrating how increasing clarity in audience with acoustic enhancement and supporting the immersive audio increases audience engagement. We will show what can be improved to elevate the experience in a converged approach. The paper will illustrate how a convergence of audio technologies, infrastructure, and a unified design and engineering processes is creating far greater opportunities for artistic experimentation and expression.

Gli stili APA, Harvard, Vancouver, ISO e altri

9

Hiremath, Nandeesh, Vaibhav Kumar, Nicholas Motahari e Dhwanil Shukla. "An Overview of Acoustic Impedance Measurement Techniques and Future Prospects". Metrology 1, n. 1 (11 maggio 2021): 17–38. http://dx.doi.org/10.3390/metrology1010002.

Testo completo

Abstract (sommario):

In order to progress in the area of aeroacoustics, experimental measurements are necessary. Not only are they required for engineering applications in acoustics and noise engineering, but also they are necessary for developing models of acoustic phenomenon around us. One measurement of particular importance is acoustic impedance. Acoustic Impedance is the measure of opposition of acoustical flow due to the acoustic pressure. It indicates how much sound pressure is generated by the vibration of molecules of a particular acoustic medium at a given frequency and can be a characteristic of the medium.The aim of the present paper is to give a synthetic overview of the literature on impedance measurements and to discuss the advantage and disadvantage of each measurement technique. In this work, we investigate the three main categories of impedance measurement techniques, namely reverberation chamber techniques, impedance tube techniques, and far-field techniques. Theoretical principles for each technique are provided along with a discussion on historical development and recent advancements for each technique.

Gli stili APA, Harvard, Vancouver, ISO e altri

10

Wang, Zhen Jiang, e Feng Hua Lu. "The Acoustical Design of Conference Room Based on Speech Acoustic". Applied Mechanics and Materials 507 (gennaio 2014): 127–30. http://dx.doi.org/10.4028/www.scientific.net/amm.507.127.

Testo completo

Abstract (sommario):

Based on the the requirements of appropriate reverberation time for the speech acoustic-dominated conference room, which are stipulated in Code for architectural acoustical design of theater ,cinema and multi-use auditorium(GB/T 50356-2005), this paper is trying to redesign the conference room on the fifth floor of the college of architecture and civil engineering of Taiyuan University of Technology, on account of the problems found after the experimental measurement. And the author introduces Ecotect to simulate the redesigning plan, in the hope of providing reference to acoustical design for the speech acoustic-dominated conference room.

Gli stili APA, Harvard, Vancouver, ISO e altri

11

Autio, Hanna, Mathias Barbagallo, Carolina Ask, Delphine Bard Hagberg, Eva Lindqvist Sandgren e Karin Strinnholm Lagergren. "Historically Based Room Acoustic Analysis and Auralization of a Church in the 1470s". Applied Sciences 11, n. 4 (10 febbraio 2021): 1586. http://dx.doi.org/10.3390/app11041586.

Testo completo

Abstract (sommario):

Worship space acoustics have been established as an important part of a nation’s cultural heritage and area of acoustic research, but more research is needed regarding the region of northern Europe. This paper describes the historical acoustics of an important abbey church in Sweden in the 1470s. A digital historical reconstruction is developed. Liturgical material specific to this location is recorded and auralized within the digital reconstruction, and a room acoustic analysis is performed. The analysis is guided by liturgical practices in the church and the monastic order connected to it. It is found that the historical sound field in the church is characterized by the existence of two distinct acoustical subspaces within it, each corresponding to a location dedicated to the daily services of the monastical congregations. The subspaces show significantly better acoustic conditions for liturgical activities compared to the nave, which is very reverberant under the conditions of daily services. Acoustic transmission from the two subspaces is limited, indicating that the monastic congregations were visually and acoustically separated from the visitors in the nave and each other.

Gli stili APA, Harvard, Vancouver, ISO e altri

12

Prives, Leslie. "Good Vibrations: Schnitta Tackling Acoustical Engineering". IEEE Women in Engineering Magazine 8, n. 2 (dicembre 2014): 35–37. http://dx.doi.org/10.1109/mwie.2014.2353294.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

13

Brandão, Eric, William D'Andrea Fonseca e Paulo Henrique Mareze. "An algorithmic approach to electroacoustical analogies". Journal of the Acoustical Society of America 152, n. 1 (luglio 2022): 667–78. http://dx.doi.org/10.1121/10.0012886.

Testo completo

Abstract (sommario):

The low-frequency behavior of acoustical transducers can be simulated with the so-called electroacoustical analogies (or lumped parameters). The main idea is that visual inspection of the transducer allows the derivation of an electroacoustic circuit that can be analyzed. The technique is computationally efficient and provides significant physical insight into the transducer. Electroacoustical analogies are taught today in many courses around the world. However, it is difficult to find reading material with an algorithmic approach to derive the electroacoustic circuit from the visual inspection of the transducer. This paper presents algorithms to derive the mechanical and acoustical circuits of transducer systems and how to couple the electrical, mechanical, and acoustical circuits for electrodynamic and capacitive transducers. A number of examples of the derivation are presented in detail. These techniques were conceived from an extensive search of the classical literature in acoustics and adapted to the teaching needs of undergraduate and graduate students of the Acoustical Engineering at the Federal University of Santa Maria in Brazil.

Gli stili APA, Harvard, Vancouver, ISO e altri

14

Markham, Benjamin E. "An expanding pipeline: 20 + years of Acentech internships". Journal of the Acoustical Society of America 154, n. 4_supplement (1 ottobre 2023): A18. http://dx.doi.org/10.1121/10.0022643.

Testo completo

Abstract (sommario):

Acoustics interns at Acentech, a multidisciplinary acoustics, technology, and noise & vibration control consultancy based in Cambridge, Massachusetts, USA, have included undergraduate and graduate students as well as graduates in many fields of engineering, physics, and architecture. Acentech interns work on a deliberate mix of both project work and internal research and development, often inspired by research presented by academics in our field. For a time, interns were typically from one of approximately a dozen US-based graduate programs in acoustic, and more rarely, from one or two undergraduate programs with acoustics concentrations. In recent years, successful interns have hailed from an increasingly wide array of university programs, and the results have exceeded expectations: an increasingly diverse pipeline of skilled, intellectually curious individuals with a passion for music, buildings, and acoustical design.

Gli stili APA, Harvard, Vancouver, ISO e altri

15

Wu, Jiu Hui, Boris Luk’yanchuk, Hua Ling Chen e Ai Qun Liu. "Light-Driven Acoustic Band Gap Based on Metal Nanospheres". Advanced Materials Research 74 (giugno 2009): 17–20. http://dx.doi.org/10.4028/www.scientific.net/amr.74.17.

Testo completo

Abstract (sommario):

In this paper, light-driven acoustic band gap is presented by considering two metal nanospheres illuminated simultaneously by laser and acoustic waves. The interaction between the photonics and phonons is investigated through optical distribution force, van der Waals distribution force, and acoustic pressure upon these nanospheres. Based on the optical force and van der Waals force, the acoustic form functions for the metal nanoaggregates with different optical intensity are calculated, and the light-driven acoustics band gap at low frequency band has been found. It is shown that the band gap width can be widened with increasing the incident laser intensity, or by using proper metal materials and background media. This could provide potential applications in optical nanoswitches and acoustical filters.

Gli stili APA, Harvard, Vancouver, ISO e altri

16

Golden, Matthew, Ethan Bourdeau, Jeffrey Fullerton, Herb Singleton, Karl Peterman e Andrew Barnard. "Overview of technical certificate program from the Institute of Noise Control Engineering". Journal of the Acoustical Society of America 152, n. 4 (ottobre 2022): A66. http://dx.doi.org/10.1121/10.0015564.

Testo completo

Abstract (sommario):

Standards are often misunderstood by even the most seasoned of acoustic professionals, let alone new technicians and engineers in the field, as they are often very complicated, written in piecemeal fashion by committees and are updated often. Some of the standards even conflict with one another. To help alleviate this problem, the Institute of Noise Control Engineering (INCE) is developing two technical certificate programs designed to educate and evaluate participants on the details of common standards used in the noise control industry. Each program will contain education, testing, and continuing education on ASTM International and Acoustics Society of America (ASA) standards. The first program will cover general acoustical measurements and environmental noise measurements. The second program will cover field testing of building acoustics, including airborne and impact noise insulation as described in ASTM E336, ASTM E1007, and associated standards. The courses are currently being developed with a target launch date of early 2023. Comparisons to similar programs that have been developed in other countries will be included. A business case will be made on how these programs will save noise control engineering firms time and money in training new staff.

Gli stili APA, Harvard, Vancouver, ISO e altri

17

Liu, Xu, Xiao Qin Liu e Chang Liu. "Development of Near-Field Acoustical Holograph and its Review". Advanced Materials Research 971-973 (giugno 2014): 1598–601. http://dx.doi.org/10.4028/www.scientific.net/amr.971-973.1598.

Testo completo

Abstract (sommario):

Near-field acoustic holography (NAH) is a powerful technique for identifying noise sources and visualizing acoustic field.The theory and algorithm of NAH techniques are introduced , and it is proved by experiment and simulation. The researches on near field acoustical holography (NAH) are reviewed，including the sound field separation technique and Patch NAH technique arisen in recent years.The difficulties in NAH and research on current situations are discussed , Finally,some engineering applications are introduced by detailed examples.

Gli stili APA, Harvard, Vancouver, ISO e altri

18

Cho, Yong Thung, M. J. Roan e J. S. Bolton. "A comparison of near-field beamforming and acoustical holography for sound source visualization". Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science 223, n. 4 (16 gennaio 2009): 819–34. http://dx.doi.org/10.1243/09544062jmes1209.

Testo completo

Abstract (sommario):

Acoustical holography procedures make high-resolution visualization possible via estimation of the sound intensity on surfaces closer to the sources than the near-field measurement surface. Another source localization technique, beamforming, has been used to estimate the direction of arrival of sound from sources that typically lie in the far-field. However, little work has been done using beamforming as a visualization technique based on near-field measurements. As a result, the performance of beamforming and acoustical holography in terms of source resolution capabilities has not been directly compared when using near-field measurements. In this work, point source beamforming was used to visualize sources based on near-field measurements. Acoustic intensity estimated from beamformed pressure measurements was compared with the absolute intensity estimated using acoustical holography techniques. In addition to noise-free, anechoic simulations, cases of measurement pressure with random noise were generated and used to compare source resolution accuracy of acoustical holography and beamforming techniques in the presence of measurement noise. It was found that intensity estimated using acoustical holography provided the clearest image of sources when the measurement surface was conformal with the source geometry. However, sources can be resolved more accurately using near-field beamforming than acoustical holography at high frequencies when the sources are not located perfectly on a surface conformal with the measurement geometry.

Gli stili APA, Harvard, Vancouver, ISO e altri

19

Kumar, Sanjay, e Heow Pueh Lee. "Recent Advances in Acoustic Metamaterials for Simultaneous Sound Attenuation and Air Ventilation Performances". Crystals 10, n. 8 (7 agosto 2020): 686. http://dx.doi.org/10.3390/cryst10080686.

Testo completo

Abstract (sommario):

In the past two decades, acoustic metamaterials have garnered much attention owing to their unique functional characteristics, which are difficult to find in naturally available materials. The acoustic metamaterials have demonstrated excellent acoustical characteristics that paved a new pathway for researchers to develop effective solutions for a wide variety of multifunctional applications, such as low-frequency sound attenuation, sound wave manipulation, energy harvesting, acoustic focusing, acoustic cloaking, biomedical acoustics, and topological acoustics. This review provides an update on the acoustic metamaterials’ recent progress for simultaneous sound attenuation and air ventilation performances. Several variants of acoustic metamaterials, such as locally resonant structures, space-coiling, holey and labyrinthine metamaterials, and Fano resonant materials, are discussed briefly. Finally, the current challenges and future outlook in this emerging field are discussed as well.

Gli stili APA, Harvard, Vancouver, ISO e altri

20

Lindberg, Jan, e Mark Moffett. "Acoustical Society of America Silver Medal in Engineering Acoustics: John L. Butler". Journal of the Acoustical Society of America 138, n. 3 (settembre 2015): 1861–64. http://dx.doi.org/10.1121/1.4934192.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

21

Zagrai, Nickolay, e Vladislav Zakharevitch. "Integration discipline acoustical engineering for training specialists in acoustics and close areas". Journal of the Acoustical Society of America 117, n. 4 (aprile 2005): 2390. http://dx.doi.org/10.1121/1.4785813.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

22

Paul, Stephan, Andrey R. da Silva, Erasmo F. Vergara e Dinara X. da Paixão. "Brazil’s first undergraduate course in acoustical engineering." Journal of the Acoustical Society of America 128, n. 4 (ottobre 2010): 2308. http://dx.doi.org/10.1121/1.3508121.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

23

Surez, E. "A successful undergraduate program in acoustical engineering." Journal of the Acoustical Society of America 128, n. 4 (ottobre 2010): 2342. http://dx.doi.org/10.1121/1.3508291.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

24

Rindel, Jens Holger. "A note on meaningful acoustical parameters for open-air theatres". Acta Acustica 7 (2023): 20. http://dx.doi.org/10.1051/aacus/2023015.

Testo completo

Abstract (sommario):

The acoustics of performance spaces are usually characterized by the reverberation time and a handful of other acoustical parameters defined in ISO 3382-1. However, these parameters have been derived with closed spaces in mind, and it is not obvious that the same parameters are meaningful in an open-air theatre. The lack of late reflections means that the decay curve is often far from a straight line, and the reverberation parameters turn out to be unreliable. Also, parameters that use the balance between early and late reflections are problematic when late reflections are more or less absent. It is necessary to rethink the need for acoustical parameters instead of sticking to the well-established parameters meant for concert halls. The most important acoustical features of a theatre are that speech is sufficiently loud and clear, which can be described by acoustical parameters for strength and clarity. In addition, it is important to avoid echoes, which are more likely to appear in an outdoor environment than in a room. Thus, there is a need for an objective echo parameter. Acoustical parameters that vary strongly with receiver position are not well suited for a global characterization of the acoustics of a space. For this purpose, a parameter for the acoustical efficiency is suggested; it is defined as ten times the logarithm of the total sound energy in the impulse response relative to the energy of the direct sound. The spatial average of this parameter can be used for comparison of the acoustics of different open-air theatres.

Gli stili APA, Harvard, Vancouver, ISO e altri

25

Torres, Julio Cesar Boscher. "Acoustical Evaluation of the Itacuruçá Baptist Evangelical Church". International Journal of Architectural Engineering Technology 9 (28 dicembre 2022): 109–24. http://dx.doi.org/10.15377/2409-9821.2022.09.8.

Testo completo

Abstract (sommario):

This paper presents the acoustical evaluation of a representative evangelical church in Rio de Janeiro, Brazil. The analysis, performed through measurements and simulations, has shown that the acoustic field needs to be more appropriate for the temple’s actual use. The analysis measured the impulse responses at 14 positions from 2 source locations and calculated Reverberation Time and Clarity Factor acoustic parameters. According to the literature and the ISO standards, the Reverberation Time was considered higher than the optimum value for both speech or music. An acoustic model for the temple was developed using the BRASS simulator. The simulation results were compared to measured data to validate the acoustic model. Based on that and aiming to achieve optimum acoustic parameters, a new model was proposed to evaluate alternatives to adequate the acoustical characteristics of the temple. The strategy to develop the final model and to achieve the target Reverberation Time is presented and discussed. An acoustic intervention is then proposed and evaluated using simulated data. The results obtained with the proposed changes, which considered the inclusion of perforated panels and carpet in some walls, were adequate, providing Reverberation Time in accordance to the standards and significant improvement to Clarity for music and speech.

Gli stili APA, Harvard, Vancouver, ISO e altri

26

Dlhý, Dušan. "The Effect of Free Joints on Sound Insulation of Constructions". Advanced Materials Research 855 (dicembre 2013): 233–36. http://dx.doi.org/10.4028/www.scientific.net/amr.855.233.

Testo completo

Abstract (sommario):

Noise protection of a building ́s interior is one of the fundamental functions of building constructions. These constructions can be understood as internal partitions, ceilings or external wall-/roof claddings. However, walls often consist of basic building materials and openings; such windows and doors as well as the acoustical properties of such structures are determined by both parts (e.g., a windows and the wall structure). The acoustical quality of opening is in general affected not only by the particular structure, but also by the concept of the mounting. Acoustical requirements should be applied in all its parts, such as the construction of the window (door) frame, window (door) wing and the realization of the functional gap as well as by application of a sealant. On the base of experimental measurements in Acoustics Chambers of the Faculty of Civil Engineering of Slovak Technical University and mathematical analysis we have determined index of sound insulation of free joint.

Gli stili APA, Harvard, Vancouver, ISO e altri

27

Okhovatian, Sogand, e Viken Koukounian. "Construction and validation of computational techniques as part of a holistic approach to complex engineering design". INTER-NOISE and NOISE-CON Congress and Conference Proceedings 269, n. 1 (14 luglio 2024): 1019–25. http://dx.doi.org/10.3397/nc_2024_0135.

Testo completo

Abstract (sommario):

As a full-service provider of bespoke solutions to environmental noise problems, there is a need to have a precise understanding of the performance of our engineered products and complex assemblies. More specifically, there are risks, as well as limitations, to relying solely on a single scientific method-e.g., empirical, computational, numerical or analytical. In the following paper, we describe the validation process of sophisticated computational software-a suite of Siemens software-to bolster our risk assessment practices. Although computational tools generally require extensive 'calibration,' our interest in pursuing the software is to model diverse constraints and environmental conditions of projects, which cannot be 'simply' assessed using empirical, numerical and analytical tools. Herein are presented examples of projects utilizing our holistic approach to assuring the performance of our engineering solutions. More specifically, we employ aero-vibro-acoustical simulations to model the aero-vibro-acoustical performance (e.g., airflow and pressure drop, dynamic insertion loss) of our industrial acoustic silencers (and similar complex assemblies).

Gli stili APA, Harvard, Vancouver, ISO e altri

28

Riccardi, Peter J., Zane T. Rusk, John A. Case, Heui Young Park e Eric Rokni. "Penn State ASA student chapter educational workshops in engineering design tools for loudspeaker and amplifier system design". Journal of the Acoustical Society of America 152, n. 4 (ottobre 2022): A255. http://dx.doi.org/10.1121/10.0016191.

Testo completo

Abstract (sommario):

Hands-on workshops and projects are an effective way to provide meaningful and memorable STEM education. To promote practical acoustics and engineering knowledge, the Pennsylvania State University Acoustical Society of America student chapter hosted a series of workshops wherein students learned the basics of electroacoustic transduction, mechanical modeling, electronics design, and PCB routing. This educational effort was accomplished by sponsoring a three-way loudspeaker design project. Transduction topics were covered by optimizing the model of a ported woofer in MathWorks SimScape, using the recently developed Acoustical Domain for Simscape available from MATLAB central. Mechanical modeling of the three-way speaker cabinets to produce manufacturing drawings was covered in SolidWorks workshops. Finally, the basics of circuit design, schematic capture, and PCB routing were covered in DipTrace through the design of a stereo integrated amplifier with an active crossover that was built to power the loudspeaker. Details about the workshops and performance of the designed components will be presented.

Gli stili APA, Harvard, Vancouver, ISO e altri

29

Wang, Lily M., Erica E. Ryherd, Joseph A. Turner e Jinying Zhu. "Graduate studies in acoustics at the University of Nebraska – Lincoln within the College of Engineering". Journal of the Acoustical Society of America 152, n. 4 (ottobre 2022): A124. http://dx.doi.org/10.1121/10.0015758.

Testo completo

Abstract (sommario):

Those interested in pursuing graduate studies and conducting research in acoustics are invited to learn more about opportunities at the University of Nebraska – Lincoln (UNL) within the College of Engineering. Dr. Lily Wang and Dr. Erica Ryherd work on architectural acoustics and noise control topics (http://nebraskaacousticsgroup.org ) within the Durham School of Architectural Engineering and Construction, based at UNL's Scott Campus in Omaha. Dr. Jinying Zhu in Civil and Environmental Engineering (also based on UNL’s Scott Campus in Omaha) is active in structural acoustics, using ultrasonic waves for concrete evaluation (https://engineering.unl.edu/cee/faculty/jinying-zhu/). Dr. Joseph Turner in Mechanical and Materials Engineering (based at UNL’s City Campus in Lincoln) focuses on ultrasound propagation through complex media for quantitative characterization of materials/microstructure (http://quisp.unl.edu ). This poster presents the graduate-level acoustics courses and lab facilities at UNL within the College of Engineering, and highlights the research interests and achievements of our faculty, graduates, and students. Extracurricular experiences are available through an Acoustical Society of America student chapter based on the Scott Campus and collaborations with Boys Town National Research Hospital.

Gli stili APA, Harvard, Vancouver, ISO e altri

30

Gong, Zhixiong, Shiyu Li e Zhichao Ma. "Single focused-beam acoustical tweezers: Trapping cells in 3-D". Journal of the Acoustical Society of America 154, n. 4_supplement (1 ottobre 2023): A263. http://dx.doi.org/10.1121/10.0023472.

Testo completo

Abstract (sommario):

Single focused beams have shown great potential in acoustofluidics and medical ultrasound because of their large pressure gradient and acoustic-thermal effect, such as acoustical tweezers and high-intensity focused ultrasound (HIFU) technique. However, the three-dimensional trapping of typical cells is still challenging since cells in water have a positive acoustic contrast factor and will be repulsive from the focus [Gong and Baudoin, Phys. Rev. Applied 18, 044033 (2022)]. In this work, to reverse this positive acoustic contrast factor into negative, we propose to use a cell-friendly medium (made of iodixanol with water) [Augustsson et al., Nat. Commun. 7, 11556 (2016)]. This enables a single focused beam to selectively trap and control cells in 3-D, and more importantly, keeps the manipulated cells with good viability. This work will extend the applications of acoustical tweezers, which may be beneficial to single cell analysis, cellular phenotyping, precise assembly of different cells in tissue engineering, and controlled drug delivery.

Gli stili APA, Harvard, Vancouver, ISO e altri

31

Carvalho, António P. O., António E. J. Morgado e Luís Henrique. "Relationships between Subjective and Objective Acoustical Measures in Churches". Building Acoustics 4, n. 1 (marzo 1997): 1–20. http://dx.doi.org/10.1177/1351010x9700400101.

Testo completo

Abstract (sommario):

This study reports on subjective and objective acoustical field measurements made in a survey of 36 Catholic churches in Portugal built in the last 14 centuries. Monaural acoustical measurements (RT, EDT. C80, D50, TS and L) were taken at several source/receiver locations in each church and a group of college students was asked to judge the subjective quality of music. The listeners in each church evaluated live music performances at similar locations in each room. Evaluation sheets were used to record the listeners' overall impressions of room acoustic quality and also Loudness, Reverberance. Intimacy. Envelopment. Directionality, Balance, Clarity, Echoes and Background Noise. This paper concentrates on the relationships of the subjective parameters with the objective room acoustics measures and with the architectural features of the churches. Correlation analyses and statistical modeling identified significant relationships among the measures. For instance, linear correlation coefficients (| R|) of 0.8–0.9 were found for the relationships: Reverberance/RT and Clarity/C80; the maximum | R| found was 0.93 for Echoes/RT. Regarding architectural features the maximum | R | found was 0.87 between Intimacy and Total Volume.

Gli stili APA, Harvard, Vancouver, ISO e altri

32

Kienemund, Daniel, Nicole Bohn, Thomas Fink, Mike Abrecht, Walter Bigler, Joachim R. Binder, Rolf Jakoby e Holger Maune. "Design and demonstration of acoustically optimized, fully-printed, BST MIM varactors for high power matching circuits". International Journal of Microwave and Wireless Technologies 10, n. 5-6 (17 aprile 2018): 620–26. http://dx.doi.org/10.1017/s1759078718000387.

Testo completo

Abstract (sommario):

AbstractThis work addresses the piezoelectric induced reduction of quality factor in fully-printed metal-insulator-metal (MIM) barium strontium titanate (BST) thick film varactors designed for high power operation. An acoustically optimized varactor design is presented and compared to a non-optimized high-power varactor. The design is utilized to present a narrowband acoustic suppression technique based on defined weights. The acoustically optimized varactor consists of 162 varactor cells in a capacitive matrix. The cells in the matrix are interconnectable allowing for a variable unbiased capacitance and power rating. Due to this setup, surface acoustic waves are interrupted, and the reduced size of the cells allows for a reduced BST layer thickness, shifting the acoustic resonance away from the operational frequency. Therefore, an inverted behavior in comparison to the high-power varactor is observed with an increasing quality factor with biasing voltage. Compared to the high-power varactor, the acoustically optimized varactor design shows a 40% increased quality factor in biased state. By applying the narrowband acoustic suppression technique, an increase in quality factor of 145% is achieved compared to the unsuppressed design. In comparison to the high-power varactor, the acoustical suppressed design shows an increase in quality factor of 480% at the first acoustic resonance frequency.

Gli stili APA, Harvard, Vancouver, ISO e altri

33

Okhovatian, Sogand, e Viken Koukounian. "Using empirical data to validate the role of computational fluid dynamics in various stages of aero-acoustic simulations". Journal of the Acoustical Society of America 155, n. 3_Supplement (1 marzo 2024): A62—A63. http://dx.doi.org/10.1121/10.0026809.

Testo completo

Abstract (sommario):

The purpose of utilizing higher level of understanding techniques is to improve the overall outcome of any process. As a full-service provider of complex engineering solutions to environmental noise problems, there is a need to house specialized knowledge to design and deliver bespoke solutions that are compatible with various constraints that implicate numerous subjects (acoustics, aerodynamics, structural, materials/chemical compatibility). The physics associated with seemingly simple products, such as an industrial acoustic silencer, is often complex. More specifically, its study should be described as aero-vibro-acoustical—whereby (1) airflow causes vibrations in the structure of the silencer, (2) the vibrations generate airborne and structureborne noise, and (3) components of the silencer (i.e., baffles) attenuate noise propagating through the duct. Motivated to expand our understanding of our products’ performances, we are using Siemens software to circumvent exhaustive laboratory testing that is cost-prohibitive, and which is, generally, limited to common geometries and parameters. A systematic approach is necessary to validate correlations between simulated results with empirical data. This is accomplished by, first, correlating the aerodynamic performance of products using computational fluid dynamics (CFD) to predict pressure drop values and the distribution of forces on the structure, to then leverage additional solvers to assess the vibro-acoustical stage of the analysis.

Gli stili APA, Harvard, Vancouver, ISO e altri

34

Grelowska, Grażyna, e Eugeniusz Kozaczka. "Underwater Acoustic Imaging of the Sea". Archives of Acoustics 39, n. 4 (1 marzo 2015): 439–52. http://dx.doi.org/10.2478/aoa-2014-0048.

Testo completo

Abstract (sommario):

Abstract Acoustic waves are a carrier of information mainly in environments where the use of other types of waves, for example electromagnetic waves, is limited. The term acoustical imaging is widely used in the ultrasonic engineering to imaging areas in which the acoustic waves propagate. In particular, ultrasound is widely used in the visualization of human organs-ultrasonography (Nowicki, 2010). Expanding the concept, acoustical imaging can also be used to presentation (monitoring) the current state of sound intensity distribution leading to characterization of sources in observed underwater region. This can be represented in the form of an acoustic characteristic of the area, for example as a spectrogram. Knowledge of the underwater world which is built by analogy to the perception of the space on the Earth's surface is to be systematize in the form of images. Those images arise as a result of graphical representation of processed acoustic signals. In this paper, it is explained why acoustic waves are used in underwater imaging. Furthermore, the passive and active systems for underwater observation are presented. The paper is illustrated by acoustic images, most of them originated from our own investigation.

Gli stili APA, Harvard, Vancouver, ISO e altri

35

Jasinski, Christopher M., e Robert D. Celmer. "Effective educational practices, assessment, and applications in acoustics and vibration at the University of Hartford". Journal of the Acoustical Society of America 152, n. 1 (luglio 2022): 633–39. http://dx.doi.org/10.1121/10.0012697.

Testo completo

Abstract (sommario):

The University of Hartford is home to two unique undergraduate engineering majors in acoustics, both sharing a core course layout of acoustics, vibrations, and projects. The Bachelor of Science in Mechanical Engineering with an Acoustics Concentration and the Bachelor of Science in Engineering in Acoustical Engineering and Music programs allow for two complementary tracks within the acoustics field, providing cohesive plans of study on many facets of listening and design. All Mechanical Engineering majors (regardless of concentration) are required to take Vibrations I and a course in Engineering and Environmental Acoustics. The department philosophy for this inclusion is that acoustics and vibration design considerations are an essential component for the development of the complete mechanical engineer. This paper outlines program educational goals and outcomes, along with pedagogical adjustments made based on continuous assessment and evaluation of select courses, including recent changes to adapt to measured deficiencies. The paper also details the historical development of the acoustics program, components of the Vibrations I and Engineering & Environmental Acoustics courses, and example research and design projects based on work in these courses. Among the included projects are modal analysis, community room acoustics assessment, and an open access computational room acoustics simulator for use and collaboration with colleagues in acoustics education.

Gli stili APA, Harvard, Vancouver, ISO e altri

36

Graham, Megan E. "Long-term care as contested acoustical space: Exploring resident relationships and identities in sound". Building Acoustics 27, n. 1 (8 dicembre 2019): 61–73. http://dx.doi.org/10.1177/1351010x19890478.

Testo completo

Abstract (sommario):

As the global population ages, residential care facilities are challenged to create positive living environments for people in later life. Health care acoustics are increasingly recognized as a key design factor in the experience of well-being for long-term care residents; however, acoustics are being conceptualized predominantly within the medical model. Just as the modern hospital battles disease with technology, sterility and efficiency, health care acoustics are receiving similar treatment. Materialist efforts towards acoustical separation evoke images of containment, quarantine and control, as if sound was something to be isolated. Sound becomes part of the contested space of long-term care that exists in tension between hospital and home. The move towards acoustical separation denies the social significance of sound in residents’ lives. Sound does not displace care; it emplaces care and the social relationships therein. Drawing upon ethnographic fieldwork in a Canadian long-term care facility, this article will use a phenomenological lens to explore how relationships are shaped in sound among residents living in long-term care. Ethnographic vignettes illustrate how the free flow of music through the care unit incited collective engagement among residents, reduced barriers to sharing social space and constructed new social identity. The article concludes that residents’ relationships are shaped within the acoustical milieu of the care unit and that to impose acoustical separation between residents’ living spaces may further isolate residents who are already at risk of loneliness.

Gli stili APA, Harvard, Vancouver, ISO e altri

37

Jasinski, Christopher M., e Robert Celmer. "A Capstone Acoustical Engineering Design course with industry-sponsored projects". Journal of the Acoustical Society of America 151, n. 4 (aprile 2022): A114. http://dx.doi.org/10.1121/10.0010824.

Testo completo

Abstract (sommario):

One of the transitions that engineering students must make as they enter the work force is the progression from theoretical concepts to applied/real world applications. At the University of Hartford, engineering design courses serve as culminating experiences devised to bridge this passage. One such course, Acoustics Capstone Design, challenges the student to apply the past three years' conceptual base of two acoustics and two vibration courses to a problem-solving opportunity replete with actual scenarios encountered in industry. Each year local firms approach our Engineering Applications Center for assistance with a variety of sound or vibration problems. After an initial training period, students make use of the laboratory's FFT/real time analyzers, anechoic/reverberation chambers, sound intensity and modal analysis software, acoustic modeling software, and vibration shaker/transducers. Using a consultant-client model, students work collaboratively in teams of two defining the problem, developing a method of approach, making appropriate measurements, devising alternate solutions, and ultimately delivering a written and oral presentation at the end of the semester. The arrangement regularly results in employment offers for the graduating seniors. The paper discusses specific projects and some experiences students have had with their first industrial assignment, as well as creative means of equipment acquisition.

Gli stili APA, Harvard, Vancouver, ISO e altri

38

Campbell, Richard H., e Frederick W. Bianchi. "The virtual orchestra; acoustical and audio engineering issues". Journal of the Acoustical Society of America 103, n. 5 (maggio 1998): 2824. http://dx.doi.org/10.1121/1.421926.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

39

Razavi, Zohreh. "Requirement of acoustical engineering discipline in building designs". Journal of the Acoustical Society of America 144, n. 3 (settembre 2018): 1740. http://dx.doi.org/10.1121/1.5067716.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

40

Myers, Arnold. "The acoustical engineering of brasswind instruments 1779–1929". Journal of the Acoustical Society of America 115, n. 5 (maggio 2004): 2565. http://dx.doi.org/10.1121/1.4809271.

Testo completo

Gli stili APA, Harvard, Vancouver, ISO e altri

41

Casazza, Marco, Fabrizio Barone, Elvio Bonisoli, Luca Dimauro, Simone Venturini, Marco Carlo Masoero e Louena Shtrepi. "A procedure for the characterization of a music instrument vibro-acoustic fingerprint: the case of a contemporary violin". Acta IMEKO 12, n. 3 (4 settembre 2023): 1–6. http://dx.doi.org/10.21014/actaimeko.v12i3.1445.

Testo completo

Abstract (sommario):

Violins are wooden musical instruments, whose quality is mainly evaluated on the basis of their aesthetics, as well as depending on the historical relevance of their makers. However, their acoustic quality remains a key evaluation parameter for performers and listeners. The instrument perceived quality, in turn, depends on one side, on the player, the environmental conditions and on the listeners’ psychoacoustic factors. On the other side, the quality of a violin depends on its materials, constructive and set-up parameters, that impact on the vibro-acoustical characteristics of the instrument. This work investigates a procedure for the vibro-acoustic characterization of a violin, here called vibro-acoustic fingerprint, as an example of vibro-acoustical characterization of a wooden music instrument. The procedure was applied, as a case study, to an Italian contemporary violin, built on the basis of a Guarneri del Gesù model in the year 2011.

Gli stili APA, Harvard, Vancouver, ISO e altri

42

Schomer, Paul D. "ACOUSTICAL SOCIETY OF AMERICA Silver Medal in Noise 2021: Paul D. Schomer". Journal of the Acoustical Society of America 151, n. 4 (aprile 2022): A193—A196. http://dx.doi.org/10.1121/10.0009988.

Testo completo

Abstract (sommario):

The Silver Medal is presented to individuals, without age limitation, for contributions to the advancement of science, engineering, or human welfare through the application of acoustic principles, or through research accomplishment in acoustics.

Gli stili APA, Harvard, Vancouver, ISO e altri

43

Postma, Barteld N. J., e Brian F. G. Katz. "An archaeoacoustic study on shape: the case study of the Iffland Theatre’s history (1802–1817)". Acta Acustica 7 (2023): 54. http://dx.doi.org/10.1051/aacus/2023046.

Testo completo

Abstract (sommario):

Previous studies have discussed six pre-Sabine quantifiable guidelines employed in room acoustic design: voice directivity, audience rake, “echo theory”, stage acoustics, reverberation, and length, width, and height ratios. Around the turn of the 18th century, these notions led to two shapes that were theoretically regarded optimal for rooms with acoustical demands: ellipse and semi-circle. The first of these shapes to be tested was the ellipse in the design for the Iffland Theatre (1802–1817). As the resulting acoustics were notoriously poor, contemporary architects and acousticians discussed the grounds for the failed acoustics as well as possible corrections. Multiple subsequent halls were also based on lessons learned from this acoustic failure. As part of this archaeoacoustics research, geometric acoustic numerical simulations were employed to estimate the actual and renovated room acoustic conditions. Three configurations of the hall have been reconstructed. Results show that the hall’s shape led to sound focusing and that the rounded proscenium arch likely induced echoes. Proposed solutions of the time to increase the scattering or absorption appear unlikely to have solved the observed acoustic problems.

Gli stili APA, Harvard, Vancouver, ISO e altri

44

Rawlinson, R. D. "Acoustic Design of Lightweight Gas Turbine Enclosures". Journal of Engineering for Gas Turbines and Power 113, n. 4 (1 ottobre 1991): 544–49. http://dx.doi.org/10.1115/1.2906275.

Testo completo

Abstract (sommario):

Acoustic enclosures for the gas turbine industry have to comply with a number of stringent safety requirements including structural strength, fire resistance, and sound insulation. This has led traditionally to heavy enclosure designs. Corrugated enclosure panels offer significant structural advantages because of their increased bending stiffness. Consequently, a corrugated panel of a given thickness can give the same structural strength as a flat panel of substantially greater weight and thickness. However, corrugated panels are intrinsically less effective as a sound insulator than flat panels of the same thickness. This paper examines the implications of corrugated, lightweight panels for acoustic enclosures. It illustrated that, by careful design, the inherent acoustical disadvantages of corrugated panels can be overcome so that thinner, lighter, and more cost-effective enclosures can be used without compromising the overall structural and acoustical design requirements.

Gli stili APA, Harvard, Vancouver, ISO e altri

45

Tang, Xiaoning, Xiansheng Zhang, Xingmin Zhuang, Huiping Zhang e Xiong Yan. "Acoustical analysis of corduroy fabric for sound absorption: Experiments and simulations". Journal of Industrial Textiles 48, n. 1 (7 agosto 2017): 201–20. http://dx.doi.org/10.1177/1528083717725912.

Testo completo

Abstract (sommario):

Corduroy fabrics have been widely used in interior decoration currently. This work mainly investigated the acoustical properties of corduroy fabrics in relation to air permeability and airflow resistance. Five specimens with similar surface density and different wale width are used. The results indicated that corduroy fabrics with thicker wale width exhibited higher air permeability and lower airflow resistance. Furthermore, the increased width of wale is beneficial to improve the acoustic absorption of corduroy fabric. Two models based on air permeability and airflow resistance are taken to characterize the acoustical behavior. It has been indicated that Pieren model could well predict the acoustic absorption coefficient of corduroy fabric, and the difference of acoustic absorption is due to the varied air permeability and airflow resistance resulting from the different wale width.

Gli stili APA, Harvard, Vancouver, ISO e altri

46

Xu, Yi Feng, e Jun Wang. "Modal Parameter Validation in Coupled Vibro-Acoustical System". Advanced Materials Research 301-303 (luglio 2011): 629–34. http://dx.doi.org/10.4028/www.scientific.net/amr.301-303.629.

Testo completo

Abstract (sommario):

The aim of this paper is to validate the modal parameters used in coupled structural finite element and acoustic boundary element algorithm to analysis the structure subjected to diffuse acoustic field. The theoretical deduction of non-symmetric coupled vibro-acoustical modal analysis was introduced firstly. In order to verify the modal truncation frequency how to affect the simulation results, based on the reciprocity theorem used in coupled FE-BE model, three different truncation frequency conditions were performed. The contrastive results show that twice the upper calculation frequency as the truncated modal frequency can make the simulation effectively and efficiently.

Gli stili APA, Harvard, Vancouver, ISO e altri

47

Watanabe, Takayuki, e Masahiro Ikeda. "Improvement of the Acoustics under the Balcony in Auditoria Using the Electro-Acoustic Method—A Study with a Full-Scale Model". Building Acoustics 18, n. 3-4 (dicembre 2011): 281–92. http://dx.doi.org/10.1260/1351-010x.18.3-4.281.

Testo completo

Abstract (sommario):

In auditoria, the acoustical properties of audience areas located under balconies are regarded as inferior to the main area. This is caused by the reduction of direct and reflected sound energy due to the smaller open area and the reduction of diffusive energy due to the limited acoustical space. In this paper, a new electro-acoustic system is proposed to compensate for this acoustical condition. The proposed system is a non-regenerative system and consists of directional microphones, head amps, a convolver, a matrix processor, amplifiers, and ceiling loudspeakers located under the balcony. The loudspeakers, located at positions corresponding to measurement points across the balcony, recreate the reflecting sound from above the balcony area, which otherwise fail to reach to the listeners under the balcony. The authors have examined the proposed system's performance via two methods: acoustical measurement using a full-scale model and a corresponding psycho-acoustical experiment. The results showed that the energy of the reflections from above the system was the same or more than that without the balcony, and the decay curve with the system was almost the same as that without the balcony. The MUSHRA method was used in the psycho-acoustical experiment, which focused on the evaluation of apparent source width (ASW) and listener envelopment (LEV). The results of the experiment show that the system is significantly better for all tests to the use of no system and that the system is superior to a standerd PA (delay system).

Gli stili APA, Harvard, Vancouver, ISO e altri

48

Park, Chan-Jae, e Chan-Hoon Haan. "Initial Study on the Reverberation Time Standard for the Korean Middle and High School Classrooms Using Speech Intelligibility Tests". Buildings 11, n. 8 (15 agosto 2021): 354. http://dx.doi.org/10.3390/buildings11080354.

Testo completo

Abstract (sommario):

The most important function of the classroom is to transmit educational information from teachers to students more accurately and clearly. The acoustical environment of the classroom thus has an important effect on the improvement of students’ learning ability. To provide an appropriate acoustical environment for learning to students, it is necessary to create an acoustical performance standard for classrooms and a guideline for designing classrooms. However, in Korea, there is not an acoustical standard for classrooms; thus, it is difficult to control and manage appropriate acoustical performance when designing and building classrooms. The present study aims to suggest acoustic performance standards for classrooms that are suitable for the Korean language. In order to perform this study, standard classrooms were created by standardizing architectural dimensions of 17 middle and high school classrooms in Cheong-ju. Speech intelligibility tests were conducted using three different languages including Korean, English, and Chinese. Twenty native speakers for each language were used as subjects for the speech intelligibility tests. Finally, auralized sound sources were created with five different conditions of reverberation time (0.47~1.22 s) by changing indoor sound absorption of a real classroom. Listening tests were undertaken by 52 Korean adults with normal hearing, using the auralized sound source. The results proved that the most appropriate reverberation time for learning was above 0.76 s. Based on the research findings, the ideal acoustical performance standard for classrooms in Korea is as follows: background noise is below 35 dBA, and reverberation time is below 0.80 s. It is also necessary that indoor sound absorption should be above 20% without sound absorption on side walls in order to satisfy with the acoustical performance standard.

Gli stili APA, Harvard, Vancouver, ISO e altri

49

T., Pazara. "Sound propagation modelling in a lecture hall". Scientific Bulletin of Naval Academy XXII, n. 2 (15 dicembre 2019): 276–83. http://dx.doi.org/10.21279/1454-864x-19-i2-033.

Testo completo

Abstract (sommario):

For lecture halls, intelligibility of speech is the most important aspect. To achieve a relative uniform distribution of sound among the listeners, a number of parameters must be taken into account. One method to speed up the design process of a lecture hall is to model the sound propagation in that room using computer acoustic software. In this paper, the authors have chosen a lecture hall from Naval Academy and made numerous simulations to discover what are the week points regarding the acoustics of this room. The acoustical parameters obtained from simulations are compared with the desired ones and a few remarks for the improvement of the room are made.

Gli stili APA, Harvard, Vancouver, ISO e altri

50

Beranek, Leo L. "The Acoustical Design of Concert Halls". Building Acoustics 1, n. 1 (marzo 1994): 3–25. http://dx.doi.org/10.1177/1351010x9400100102.

Testo completo

Abstract (sommario):

A brief account is given of the early history of room acoustics and in particular W.C. Sabine's discovery of the importance of reverberation time on the acoustical quality of a room. There follows an account of later work, including that of the author, in which five other parameters, i.e. initial time delay, loudness, diffusion, spatial impression and early to late energy ratio, were identified as contributing to acoustical quality. The acoustical design of a number of halls after 1950 is discussed and an account is given of the history of the design of the Philharmonic Hall in the Lincoln Center up to the present time. Some attempts made by architects to break away from the safe shoe-boxed shape of hall are described and the acoustical consequences discussed. The success of four recently designed halls is shown to be the direct result of lessons learned both from experience in real halls and the fundamental research work mentioned in this paper. Finally, a brief account is given of the objective parameters that can now be measured in halls and which relate to subjective response.

Gli stili APA, Harvard, Vancouver, ISO e altri

Articoli di riviste sul tema "Acoustical engineering"

Cita una fonte nei formati APA, MLA, Chicago, Harvard e in molti altri stili