Literatura académica sobre el tema "Hot melt adhesive smart adhesive"
Crea una cita precisa en los estilos APA, MLA, Chicago, Harvard y otros
Consulte las listas temáticas de artículos, libros, tesis, actas de conferencias y otras fuentes académicas sobre el tema "Hot melt adhesive smart adhesive".
Junto a cada fuente en la lista de referencias hay un botón "Agregar a la bibliografía". Pulsa este botón, y generaremos automáticamente la referencia bibliográfica para la obra elegida en el estilo de cita que necesites: APA, MLA, Harvard, Vancouver, Chicago, etc.
También puede descargar el texto completo de la publicación académica en formato pdf y leer en línea su resumen siempre que esté disponible en los metadatos.
Artículos de revistas sobre el tema "Hot melt adhesive smart adhesive"
IMAHORI, Makoto. "Hot Melt Adhesive". Journal of The Adhesion Society of Japan 42, n.º 11 (2006): 471–80. http://dx.doi.org/10.11618/adhesion.42.471.
Texto completoWu, Zijin, Yonggang Shangguan, Chunhui Zhang y Qiang Zheng. "Effects of Crosslinking and Silicone Coupling Agent on Properties of EVA Composite Hot Melt Adhesive". Polymers 13, n.º 23 (25 de noviembre de 2021): 4101. http://dx.doi.org/10.3390/polym13234101.
Texto completoMuroi, Soichi, Shigetoshi Seta, Yoshio Matsumoto, Koichi Yasui y Kazuyoshi Imamura. "4477636 Hot-melt adhesive and method". Marine Pollution Bulletin 16, n.º 3 (marzo de 1985): ii—iii. http://dx.doi.org/10.1016/0025-326x(85)90548-x.
Texto completoKuo, Chung-Feng Jeffrey, Wei Lun Lan, Jui-Wen Wang, John-Ber Chen y Pin-Hua Lin. "Hot-melt pressure-sensitive adhesive for seamless bonding of nylon fabric Part II: Process parameter optimization for seamless bonding of nylon fabric". Textile Research Journal 89, n.º 12 (31 de julio de 2018): 2294–304. http://dx.doi.org/10.1177/0040517518790970.
Texto completoG. KADAM, PRAVIN y SHASHANK T. MHASKE. "Effect of Nylon-6 Concentration on the Properties of Hot Melt Adhesive Synthesized using Dimer Acid and Ethylenediamine". Material Science Research India 9, n.º 2 (25 de diciembre de 2012): 215. http://dx.doi.org/10.13005/msri/090206.
Texto completoHwang, Sung Oh y Soo Hyang Lee. "Management of a High-Pressure Hot-Melt Adhesive Injection Injury". Journal of Wound Management and Research 16, n.º 1 (29 de febrero de 2020): 59–63. http://dx.doi.org/10.22467/jwmr.2019.00976.
Texto completoStoyanov, O. V., R. M. Khuzakhanov, Ya V. Kapitskaya, E. R. Mukhamedzyanova, R. Ya Deberdeev y S. N. Rusanova. "Hot-melt adhesive for shrinkable polyethylene collars". Polymer Science. Series D 1, n.º 3 (julio de 2008): 171–74. http://dx.doi.org/10.1134/s1995421208030088.
Texto completoNevrekar, N. B., G. A. Naik y K. A. Joshi. "A hot melt adhesive from polyester waste". Journal of Adhesion Science and Technology 1, n.º 1 (enero de 1987): 201–7. http://dx.doi.org/10.1163/156856187x00210.
Texto completoPaul, C. W. "Hot-Melt Adhesives". MRS Bulletin 28, n.º 6 (junio de 2003): 440–44. http://dx.doi.org/10.1557/mrs2003.125.
Texto completoJoža, Ana V., Dragan Z. Stupar, Jovan S. Bajić, Bojan M. Dakić, Zoran Mijatović, Miloš P. Slankamenac y Miloš B. Živanov. "An End-Type Fiber-Optic UV Sensor Covered with Mixture of Two UV Sensitive Materials". Key Engineering Materials 543 (marzo de 2013): 265–68. http://dx.doi.org/10.4028/www.scientific.net/kem.543.265.
Texto completoTesis sobre el tema "Hot melt adhesive smart adhesive"
KORICHO, ERMIAS GEBREKIDAN. "Implementation of Composites and Plastics Materials for Vehicle Lightweight". Doctoral thesis, Politecnico di Torino, 2012. http://hdl.handle.net/11583/2497432.
Texto completoNasr, M., H. Karandikar, R. T. A. Abdel-Aziz, N. Moftah y Anant R. Paradkar. "Novel nicotinamide skin-adhesive hot melt extrudates for treatment of acne". Taylor and Francis, 2018. http://hdl.handle.net/10454/16734.
Texto completoHot melt extrusion is a continuous process with wide industrial applicability. Till current date, there have been no reports on the formulation of extrudates for topical treatment of dermatological diseases. The aim of the present work was to prepare and characterize medicated hot melt extrudates based on Soluplus polymer and nicotinamide, and to explore their applicability in acne treatment. The extrudates were characterized using DSC, FTIR, XRD, and DVS. The extrudates were also tested for their skin adhesion potential, ability to deposit nicotinamide in different skin layers, and their clinical efficacy in acne patients. The 10% nicotinamide extrudates exhibited amorphous nature which was reserved during storage, with no chemical interaction between nicotinamide and Soluplus. Upon contrasting the skin adhesion and drug deposition of extrudates and nicotinamide gel, it was evident that the extrudates displayed significantly higher adhesion and drug deposition reaching 4.8 folds, 5.3 folds, and 4.3 folds more in the stratum corneum, epidermis and dermis, respectively. Furthermore, the extrudates significantly reduced the total number of acne lesions in patients by 61.3% compared to 42.14% with the nicotinamide gel. Soluplus extrudates are promising topical drug delivery means for the treatment of dermatological diseases.
Korin, Christer. "Mechanical Behaviour of Adhesive Joints in Cartonboard for Packaging". Doctoral thesis, Karlstads universitet, Avdelningen för kemiteknik, 2009. http://urn.kb.se/resolve?urn=urn:nbn:se:kau:diva-4731.
Texto completoVan, Heerden Vaughn Tyronne. "A marketing strategy for SASOLWAKS in the USA hot melt adhesive industry / Vaughn Tyronne van Heerden". Thesis, North-West University, 2006. http://hdl.handle.net/10394/2513.
Texto completoSewell, Neil Thomas. "Algorithms for multi-axis additive rapid prototyping : rapid prototyping using hot-melt adhesive deposition and computer numerical controlled machining centres". Thesis, University of Exeter, 2004. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.410823.
Texto completoKallel, Achraf. "Étude d'un procédé innovant de contre-collage d'emballages flexibles par des colles thermofusibles". Thesis, Paris, ENMP, 2015. http://www.theses.fr/2015ENMP0016/document.
Texto completo“Revoluflex” is an innovative laminating process consisting in bonding two plastic films with a thin layer of hot melt adhesive. The molten adhesive is extruded through a flat die (gap ~ 1 mm). Then, it is stretched into the air at very high draw ratio (Dr> 100) over a very short distance (~ 1 mm) and set down on the primary plastic film. A vacuum pump, located beneath the extruded film, stabilizes the process and prevents air bubble intake between the primary and the adhesive film. A secondary plastic film is then laid on the coated primary film to give a laminate. Many defects can be observed as a function of the process parameters such as wavelike instabilities characterized by periodical sustained oscillations in the hot melt adhesive layer. This instability is similar to the “Draw Resonance” instability encountered with classical processes involving the stretching of a molten polymer. Other defects looking like small bubbles, cracks or rips in the adhesive layer are also observed. These defects hinder commercial deployment of the process. The aim of this study is there to understand their origins in order to remove them or at least delay their onset.These defects have first been characterized and their appearance was quantified according to process parameters and adhesive rheology. Several theoretical models of increasing complexity, in terms of flow kinematics and polymer rheology, have been developed. Newtonian and Viscoelastic constant width membrane models involving a pressure differential between the two sides of the extruded film represent a first theoretical approach that accounts for the vacuum pump effect. The linear stability method was used to investigate the influence of adhesive rheological behavior and process parameters on the onset of periodic instabilities. It was shown that the results were highly dependent on the initial flow conditions at die exit. Since the membrane assumption is not valid for very short stretching distances, we developed two Newtonian 2D models accounting for both extrusion and drawing steps. The first one is a symmetric model that does not account for the vacuum pump effect. It was solved using two different approaches: a front-tracking method coupled with linear stability analysis and a direct numerical simulation with interface capturing method (Level set method). It was shown that both methods lead to the same stationary solution and the same stability results. The second model accounts for the pressure differential and it was solved using only the front-tracking method. This latter 2D model enables to check the validity of the initial flow conditions of the membrane model.These models allow us to explain several experimental phenomena such as the stabilizing effect of the pressure differential and the short stretching distance. In addition, they help explaining experimental features which contradict the classical literature on drawing instabilities such as the stabilizing effect of increasing the draw ratio under certain operating conditions. Finally, they show that the pressure differential induces a high stress at the bottom lip of the extrusion die, which may clarify the cracks and rips observed in the adhesive layer
Kruppke, Iris, Rolf-Dieter Hund y Chokri Cherif. "Adhesion problematics and curing kinetics in a thermosetting matrix for stitch-free non-crimp fabric". Sage, 2016. https://tud.qucosa.de/id/qucosa%3A35420.
Texto completoWong, Yue-Sin y 翁悅馨. "The study of characteristics on fast adhesive of reactive polyurethane hot melt adhesive". Thesis, 2015. http://ndltd.ncl.edu.tw/handle/53134073464586152852.
Texto completo國立勤益科技大學
化工與材料工程系
103
Polyurethane reactive hot melt adhesives (PUR) are isocyanate-capped prepolymers prepared from polyester and or polyether glycols and diisocyanates. After application, PUR exhibit green strength by solidification while cooling to room temperature. PUR are NCO-terminated, therefore they will cure in the presence of moisture, generating a highly crosslinked network. The content of NCO was studied of curing speed, adhesion viscosity, tensile strength and bonding strength. By using Fourier transform infrared spectroscopy (FTIR), the distributions of hydrogen bonds in these PUR were characterized. The results showed that the PUR had a high degree of micro phase separation, and a high degree of hydrogen bonding. Adhesive properties test showed that the initial adhesive strength and crystallization properties were excellent in the presence of the low content of hard segments. PUR prepolymer with higher crystal content showed better green strength but slower adhesion development as a result of hindrance to moisture diffusion by the crystalline structure. With mixed two isocyanate and adding a catalyst to improve the cure rate and rheological properties of PUR. The fast adhesive including A4, A8, MD3, NHM3 and NHM3A4. As a result in lap shear strength test, the MD3, NHM3 and NHM3A4 at 0.5hr have a higher green strength and more than 1.6 kgf/cm2 with rubber substrate. And in the final cured strength, the MD3 is 60.25 kgf/cm2 with PC substrate and the adhesion failure modes belong to substrate failure. These fast adhesives with rubber substrate are substrate failure in final cured strength.
Chiang, Chun-wu y 蔣俊武. "The Preparation and Physical Properties of Polyurethane Hot Melt Adhesive". Thesis, 2006. http://ndltd.ncl.edu.tw/handle/27180525485870047786.
Texto completo逢甲大學
紡織工程所
95
This study presents the preparation and physical properties of Polyurethane Hot Melt Adhesive(PUHMA)based on polybutylenes adipate (PBA)as soft segment, isophorone diisocyanate (IPDI) as hard segment, 1,4-butane diol(1,4-BD)as chain extender and dibutyltin dilaurate (DBTDL) as catalyst. The polymerization was proceeded without adding any solvents in a two-pots process. . The morphology of the PUHMA were studied by X-ray and FT-IR spectrum. The thermal properties of the PUHMA were evaluated by TGA and DSC spectrum. The molecular weight and molecular weight distributions of the PUHMA were measured by GPC analysis. The T-peel tests of the PUHMA were measured by Instron strength tester. The adhesive propertied of the PUHMA laminated fabric were measured by T-peel strength tester. . The FT-IR graph of the PUHMA showed that the main peak of -NCO group disappeared in the wavelength of 2200 cm-1, which revealed a successful polymerization in preparing PUHMA. From the X-ray diffraction spectral analysis of the PUHMA, the graph showed two peaks at 21.3° and 24° in 2θ-axis, which corresponds to the (110) and (020) diffractions, respectively. The crystallinity of the PUHMA was increased as the hard segments ratio raised. Thermal properties of the PUHMA were increased to Tg as the hard segment increased. Melting point (Tm) and melting enthalpy of the PUHMA were in propertional to the molecular weight. The enhencement of hard segments of the PUHMA attributed to a small and narrow distribution of molecular weight. For the T-peel test of the PUHMA, it revealed a maximal adhesive strength correspond to the curing time. Consequently, the optimal adhesive strength was achieved if the molecular weight ratio of IPDI╱PBA╱1,4-BD was 1.0:0.8:0.2 (NCO╱OH=1). The similar result was also obtained in the curing time of 72 hr.
WU, PEI-YING y 吳沛盈. "Patent Analysis of Low Melting Point Polyamide Of Hot Melt Adhesive". Thesis, 2019. http://ndltd.ncl.edu.tw/handle/3j53a9.
Texto completo國立臺北科技大學
分子科學與工程系有機高分子碩士班
107
Polyamide, also known as nylon, was originally an important synthetic fiber raw mate-rial before it developed into engineering plastics. It is also the earliest engineering plastics. It has unique wear resistance, good friction coefficient, and excellent heat and impact re-sistance. It is widely used in textiles, shoe materials, automotive and aerospace parts, and industrial materials. This research uses the patent hierarchy search method to retrieve the technical charac-teristics of low melting point polyamines hot melt adhesive, and then analyzes the synthesis technology of low melting point polyamines hot melt adhesive materials by using the pa-tented power matrix analysis. Specifically, the research of this study The purpose is to hope that the industry will further improve the current status and trends of low melting point pol-yamines hot melt adhesive materials through patent analysis, and as a follow-up technology research and development, innovation or avoidance of design data sources, to break through patent barriers, create technological innovation, and then enhance Industrial competitive-ness.
Capítulos de libros sobre el tema "Hot melt adhesive smart adhesive"
Gooch, Jan W. "Adhesive, Hot Melt". En Encyclopedic Dictionary of Polymers, 20. New York, NY: Springer New York, 2011. http://dx.doi.org/10.1007/978-1-4419-6247-8_267.
Texto completoGooch, Jan W. "Hot-Melt Adhesive". En Encyclopedic Dictionary of Polymers, 371. New York, NY: Springer New York, 2011. http://dx.doi.org/10.1007/978-1-4419-6247-8_6045.
Texto completoZhang, Mingming, Jianxin Du y Jianwei Hao. "Study of Intumescent Flame Retardant Copolyester Hot Melt Adhesive". En ACS Symposium Series, 183–91. Washington, DC: American Chemical Society, 2012. http://dx.doi.org/10.1021/bk-2012-1118.ch013.
Texto completoWang, Xinting, Guorong Cao, Dongli Li y Meiqi Yang. "Effects of Several Surfactants on Surface Tension of PVA Hot-Melt Adhesive Tape". En Lecture Notes in Electrical Engineering, 841–46. Singapore: Springer Singapore, 2018. http://dx.doi.org/10.1007/978-981-10-7629-9_104.
Texto completo"Hot-melt adhesive". En Encyclopedic Dictionary of Polymers, 500–501. New York, NY: Springer New York, 2007. http://dx.doi.org/10.1007/978-0-387-30160-0_5951.
Texto completo"Adhesive, hot melt". En Encyclopedic Dictionary of Polymers, 28. New York, NY: Springer New York, 2006. http://dx.doi.org/10.1007/978-0-387-30160-0_256.
Texto completo"hot-melt adhesive". En The Fairchild Books Dictionary of Textiles. Fairchild Books, 2021. http://dx.doi.org/10.5040/9781501365072.7805.
Texto completoPizzi, A. "Hot-Melt Adhesives". En Handbook of Adhesive Technology, Revised and Expanded. CRC Press, 2003. http://dx.doi.org/10.1201/9780203912225.ch37.
Texto completoM. Sridhar, Laxmisha, Andrew T. Slark y James A. Wilson. "Furan Functionalized Polyesters and Polyurethanes for Thermally Reversible Reactive Hotmelt Adhesives". En Furans and Furan Derivatives - Recent Advances and Applications [Working Title]. IntechOpen, 2021. http://dx.doi.org/10.5772/intechopen.100426.
Texto completoActas de conferencias sobre el tema "Hot melt adhesive smart adhesive"
Huo, Ning-bo, Hong-xia Li y Xiao-jing Jia. "Data Analysis on Adhesive Property Testing Methods of Hot-melt Pressure-sensitive Adhesive with Styrene Thermoplastic Elastomer". En 2017 International Conference on Computational Science and Engineering(ICCSE 2017). Paris, France: Atlantis Press, 2017. http://dx.doi.org/10.2991/iccse-17.2017.13.
Texto completoHuo, Ning-bo y Chun-hai Zhao. "Study on Anti-Hygrothermal Aging Properties of TPS Hot-melt Adhesive". En 2016 6th International Conference on Applied Science, Engineering and Technology. Paris, France: Atlantis Press, 2016. http://dx.doi.org/10.2991/icaset-16.2016.55.
Texto completoHughes, Josie y Fumiya Iida. "Tack and deformation based sensorised gripping using conductive hot melt adhesive". En 2018 IEEE International Conference on Soft Robotics (RoboSoft). IEEE, 2018. http://dx.doi.org/10.1109/robosoft.2018.8405384.
Texto completoCiardiello, Raffaele, Andrea Tridello, Luca Goglio y Giovanni Belingardi. "Experimental Assessment of the Dynamic Behavior of Polyolefin Thermoplastic Hot Melt Adhesive". En ASME 2018 Pressure Vessels and Piping Conference. American Society of Mechanical Engineers, 2018. http://dx.doi.org/10.1115/pvp2018-84725.
Texto completoObata, S., T. Sekine y H. Tomita. "Hot-melt adhesive method using metal foil induction heating and performance of long E-type core head". En 2005 IEEE 11th European Conference on Power Electronics and Applications. IEEE, 2005. http://dx.doi.org/10.1109/epe.2005.219366.
Texto completoBrunella, Valentina, Giulia Spezzati, Ermias Gebrekidan Koricho, Giovanni Belingardi, Brunetto Martorana, Fabrice Bondji Ngabang y Marco Simioli. "Novel Use of Electromagnetic-Sensitive Nano-Additives to Develop Reversible Hot-Melt Adhesives". En ASME 2018 Pressure Vessels and Piping Conference. American Society of Mechanical Engineers, 2018. http://dx.doi.org/10.1115/pvp2018-84913.
Texto completoRuzafa-Silvestre, Carlos, Pilar Carbonell-Blasco, Elena Orgiles-Calpena y Francisca Aran Ais. "Low-pressure plasma treatment applied to polymeric materials for a sustainable footwear industry". En The 8th International Conference on Advanced Materials and Systems. INCDTP - Leather and Footwear Research Institute (ICPI), Bucharest, Romania, 2020. http://dx.doi.org/10.24264/icams-2020.iv.19.
Texto completoNiutta, Carlo Boursier, Raffaele Ciardiello, Giovanni Belingardi y Alessandro Scattina. "Experimental and Numerical Analysis of a Pristine and a Nano-Modified Thermoplastic Adhesive". En ASME 2018 Pressure Vessels and Piping Conference. American Society of Mechanical Engineers, 2018. http://dx.doi.org/10.1115/pvp2018-84728.
Texto completoRajamäki, E., M. Leino, P. Vuoristo, P. Järvelä y T. Mäntylä. "Effect of Powder Properties such as Particle Size, Density and Melt Flow Rate on the Properties of Flame Sprayed PE Coating". En ITSC 2000, editado por Christopher C. Berndt. ASM International, 2000. http://dx.doi.org/10.31399/asm.cp.itsc2000p0281.
Texto completo