Literatura académica sobre el tema "Floating offshore wind turbines, susbtructure optimization, frequency domain model"

Floating offshore wind turbines are a promising technology for addressing energy needs by utilizing wind resources offshore. The current state of the art is based on heavy, expensive platforms to survive the ocean environment. Typical design techniques do not involve optimization because of the computationally expensive time domain solvers used to model motions and loads in the ocean environment. However, this design uses an efficient frequency domain solver with a genetic algorithm to rapidly optimize the design of a novel floating wind turbine concept. The concept utilizes a liquid ballast mass to mitigate motions on a lightweight post-tensioned concrete platform. The simple cruciform-shaped design of the platform made of post-tensioned concrete is less expensive than steel, reducing the raw material and manufacturing cost. The use of ballast water to behave as a tuned mass damper allows a smaller platform to achieve the same motions as a much larger platform, thus reducing the mass and cost. The optimization techniques applied with these design innovations resulted in a design with a levelized cost of energy of USD 0.0753/kWh, roughly half the cost of the current state of the art.

Currently, floating offshore wind is experiencing rapid development towards a commercial scale. However, the research to design new control strategies requires numerical models of low computational cost accounting for the most relevant dynamics. In this paper, a reduced linear time-domain model is presented and validated. The model represents the main floating offshore wind turbine dynamics with four planar degrees of freedom: surge, heave, pitch, first tower fore-aft deflection, and rotor speed to account for rotor dynamics. The model relies on multibody and modal theories to develop the equation of motion. Aerodynamic loads are calculated using the wind turbine power performance curves obtained in a preprocessing step. Hydrodynamic loads are precomputed using a panel code solver and the mooring forces are obtained using a look-up table for different system displacements. Without any adjustment, the model accurately predicts the system motions for coupled stochastic wind–wave conditions when it is compared against OpenFAST, with errors below 10% for all the considered load cases. The largest errors occur due to the transient effects during the simulation runtime. The model aims to be used in the early design stages as a dynamic simulation tool in time and frequency domains to validate preliminary designs. Moreover, it could also be used as a control design model due to its simplicity and low modeling order.

Floating Offshore Wind Turbines (FOWTs) are ground-breaking systems in the renewable sector, capable to exploit wind energy in deep-water areas, where the resource is stronger and abundant with respect to onshore and near-cost sites. In this work, a coupled Frequency-Domain (FD) model of the entire system is developed and validated against time-domain simulations. The FD model is implemented in site-specific optimization procedures performed by means of Genetic Algorithm (GA, targeted at reducing the costs of the substructure without an uncontrolled penalization of the structural performances. Two installations sites in the Mediterranean Sea are chosen for the analysis. Results show that the optimization strategies give useful information about the influences of platform and mooring characteristics on the system response. Moreover, it is proved that the costs can be reduced of about the 45%, implying the reduction of the Levelized Cost Of Electricity.

Offshore floating wind turbine technology is growing rapidly and has the potential to become one of the main sources of affordable renewable energy. However, this technology is still immature owing in part to complications from the integrated design of wind turbines and floating platforms, aero-hydro-servo-elastic responses, grid integrations, and offshore wind resource assessments. This research focuses on developing methodologies to investigate the technical and economic feasibility of a wide range of floating offshore wind turbine support structures. To achieve this goal, interdisciplinary interactions among hydrodynamics, aerodynamics, structure and control subject to constraints on stresses/loads, displacements/rotations, and costs need to be considered. Therefore, a multidisciplinary design optimization approach for minimum levelized cost of energy executed using parameterization schemes for floating support structures as well as a frequency domain dynamic model for the entire coupled system. This approach was based on a tractable framework and models (i.e. not too computationally expensive) to explore the design space, but retaining required fidelity/accuracy. In this dissertation, a new frequency domain approach for a coupled wind turbine, floating platform, and mooring system was developed using a unique combination of the validated numerical tools FAST and WAMIT. Irregular wave and turbulent wind loads were incorporated using wave and wind power spectral densities, JONSWAP and Kaimal. The system submodels are coupled to yield a simple frequency domain model of the system with a flexible moored support structure. Although the model framework has the capability of incorporating tower and blade structural DOF, these components were considered as rigid bodies for further simplicity here. A collective blade pitch controller was also defined for the frequency domain dynamic model to increase the platform restoring moments. To validate the proposed framework, predicted wind turbine, floating platform and mooring system responses to the turbulent wind and irregular wave loads were compared with the FAST time domain model. By incorporating the design parameterization scheme and the frequency domain modeling the overall system responses of tension leg platforms, spar buoy platforms, and semisubmersibles to combined turbulent wind and irregular wave loads were determined. To calculate the system costs, a set of cost scaling tools for an offshore wind turbine was used to estimate the levelized cost of energy. Evaluation and comparison of different classes of floating platforms was performed using a Kriging-Bat optimization method to find the minimum levelized cost of energy of a 5 MW NREL offshore wind turbine across standard operational environmental conditions. To show the potential of the method, three baseline platforms including the OC3-Hywind spar buoy, the MIT/NREL TLP, and the OC4-DeepCwind semisubmersible were compared with the results of design optimization. Results for the tension leg and spar buoy case studies showed 5.2% and 3.1% decrease in the levelized cost of energy of the optimal design candidates in comparison to the MIT/NREL TLP and the OC3-Hywind respectively. Optimization results for the semisubmersible case study indicated that the levelized cost of energy decreased by 1.5% for the optimal design in comparison to the OC4-DeepCwind.
Graduate

Abstract This report describes the ongoing and planned development of the software package CT-Opt (Current/Tidal Optimization), a control co-design modeling tool for marine hydrokinetic turbines. The commercialization of these turbines has faced significant challenges due to the complex, multidisciplinary nature of their design and the extreme environmental conditions of their operation. This project aims to create a modeling tool that will enable the efficient design of robust, cost-competitive hydrokinetic turbine systems. Rather than using traditional optimization methods, CT-Opt combines multiple models across a range of fidelities to enable coupled optimization of the system design and system controller via a control co-design approach. With this method, the parameters that affect system performance are considered more comprehensively at every stage of the design process. The lowest-fidelity, frequency-domain model called by CT-Opt is RAFT (Response Amplitudes of Floating Turbines), which was originally developed by the National Renewable Energy Laboratory (NREL) to model response amplitudes of floating offshore wind turbines. The highest-fidelity, time-domain model is OpenFAST, which was developed by NREL for land-based and offshore wind turbines. As part of the CT-Opt project, new functionalities will be added to RAFT and OpenFAST to enable the accurate simulation of fixed and floating marine hydrokinetic turbines. In addition to expanding the capabilities of RAFT and OpenFAST, new mid-fidelity models will be developed. These models will be based on RAFT and OpenFAST and will consist of linearized, state-space models derived from the fully coupled, nonlinear OpenFAST equations and derivative function surrogate models that approximate the nonlinear system behavior. Each model will be coupled with controllers to allow control co-design methods to be applied both within models and across fidelity levels, enabling efficient system optimization.