Tesis sobre el tema "Engineering, General|Energy"
Crea una cita precisa en los estilos APA, MLA, Chicago, Harvard y otros
Consulte los 50 mejores tesis para su investigación sobre el tema "Engineering, General|Energy".
Junto a cada fuente en la lista de referencias hay un botón "Agregar a la bibliografía". Pulsa este botón, y generaremos automáticamente la referencia bibliográfica para la obra elegida en el estilo de cita que necesites: APA, MLA, Harvard, Vancouver, Chicago, etc.
También puede descargar el texto completo de la publicación académica en formato pdf y leer en línea su resumen siempre que esté disponible en los metadatos.
Explore tesis sobre una amplia variedad de disciplinas y organice su bibliografía correctamente.
Ramberg, David J. (David John). "General equilibrium impacts of new energy technologies on sectoral energy usage". Thesis, Massachusetts Institute of Technology, 2015. http://hdl.handle.net/1721.1/99536.
Texto completoThis electronic version was submitted by the student author. The certified thesis is available in the Institute Archives and Special Collections.
Cataloged from student-submitted PDF version of thesis.
Includes bibliographical references (pages 185-198).
The dissertation examines conditions under which gas-to-liquids (GTL) technology penetration shifts the crude oil-natural gas price ratio. Empirical research finds long-run relationships between crude oil and natural gas prices. Some studies include time trends that steadily evolve the pricing relationship, while others show a long-run relationship that occasionally shifts significantly. A common hypothesis is that technologies that increase substitutability or complementarity between fuels are the source of the price linkage. However, empirically measuring the effects of a gradually-penetrating technology across narrow time frames is not possible due to intervening economic shocks. This thesis examines the effects of an energy conversion technology penetration on the crude oil-natural gas price ratio through its influence on sectoral energy use in the U.S. GTL must be less expensive and more efficient, and natural gas prices must be lower, than currently forecast for an effect to be measured. In the absence of a technology that explicitly allows for substitution between natural gas and petroleum-based fuels, different rates of demand growth result in a steadily-rising oil-gas price ratio. If a viable GTL technology successfully competes against petroleum-derived refined fuels, it dampens crude oil price increases and brings the oil-gas price ratio below the levels found in cases without a viable GTL technology.
by David John Ramberg.
Ph. D.
Wang, Hao. "The effect of primary air distribution on emissions from a natural gas water heater". Marquette University, 2013.
Buscar texto completoWills, William Noah. "A General Method for Sizing Battery Energy Storage Systems for Use in Mitigating Photovoltaic Flicker". Thesis, University of Missouri - Columbia, 2019. http://pqdtopen.proquest.com/#viewpdf?dispub=13850758.
Texto completoA method for sizing battery energy storage (BES) systems for use in mitigating voltage flicker caused by solar intermittency in photovoltaic generation was developed. The method creates a “design day” from existing solar data and designs the power and energy requirements for a BES system that can help a photovoltaic facility mitigate flicker caused by solar activity associated with the design day. An economic analysis of lead-acid and lithium-ion options for the BES was also developed. The method was then applied to a proposed photovoltaic project in the Midwestern United States.
Ali, Rehan. "Effect of Solar Panel Cooling on Photovoltaic Performance". Thesis, Southern Illinois University at Edwardsville, 2014. http://pqdtopen.proquest.com/#viewpdf?dispub=1560782.
Texto completoOne of the main problems in using the photovoltaic system is the low energy conversion efficiency of photovoltaic cells and, furthermore, during the long operational period of solar cells, their energy conversion efficiency decreases even more due to increase in operating cell temperature over a certain limit. One way of improving the efficiency of photovoltaic system is to maintain a low operating temperature by cooling it down during its operation period. This study compares the effects of cooling on the performance of photovoltaic system. Experiments are performed on the solar panel inclined at fixed 45° angle without active cooling initially to have a set of reference performance parameters for comparison. Afterwards, cooling of the solar panel is carried out using air and water, separately, as the cooling fluids. I-V tests and temperature tests, for all the cases, are performed for comparative analysis. The energy balance calculations showed that the experimental results are in conformity with the theoretical results. The results further showed that the cooling of photovoltaic system using water over the front surface enhances the performance even more as compared to air cooling of solar panel.
DeLuca, Christopher. "Numerical Modeling and Optimization of Mechanically Active Electrochemical Systems". Thesis, University of Colorado at Boulder, 2013. http://pqdtopen.proquest.com/#viewpdf?dispub=3592275.
Texto completoThis work is primarily motivated by the hope that Silicon (Si) can be utilized in Lithium (Li) ion batteries to enable an order of magnitude capacity increase if Li-Si systems can be better understood. In order to create a valuable tool that could be used to study a wide range of problem, pertinent physical models were implemented in an extended finite element method (XFEM) framework written in c++. One of the major contribution of this work goes to the battery modeling community, by generalizing several existing electrochemical-mechanical models which use a small deformation approximations so they can accommodate finite deformation. A general theory which can be used to guide the development of new finite element models is presented in detail. This work also contributes new finite element modeling tools with novel predictive capabilities to the battery modeling community, which will hopefully facilitate the design and optimization of next generation battery micro-structures. Studies within demonstrate that small deformation approximation models can produce incorrect predictions about the behavior of Li-Si systems, supporting the case for using finite deformation models. The developed tools are used to demonstrate that arbitrary geometries can easily be simulated on a the same fixed grid, facilitating automated geometry studies including parameter sweeping and topology optimization.
Attalah, Said. "Energy evaluation of the High Velocity Algae Raceway Integrated Design (ARID-HV)". Thesis, The University of Arizona, 2013. http://pqdtopen.proquest.com/#viewpdf?dispub=1536266.
Texto completoThe original ARID (Algae Raceway Integrated Design) raceway was an effective method to increase temperature toward the optimal growth range. However, the energy input was high and flow mixing was poor. Thus, the ARID-HV (High Velocity Algae Raceway Integrated Design) raceway was developed to reduce energy input requirements and improve flow mixing. This was accomplished by improving pumping efficiency and using a serpentine flow pattern in which the water flows through channels instead of over barriers. A prototype ARID-HV system was installed in Tucson, Arizona, and the constructability, reliability of components, drainage of channels, and flow and energy requirements of the ARID-HV raceway were evaluated. Each of the electrical energy inputs to the raceway (air sparger, air tube blower, canal lift pump, and channel recirculation pump) was quantified, some by direct measurement and others by simulation. An algae growth model was used to determine the algae production rate vs. flow depth and time of year. Then the electrical energy requirement of the most effective flow depth was calculated. Channel hydraulics was evaluated with Manning's equation and the corner head loss equation. In this way, the maximum length of channels for several raceway slopes and mixing velocities were determined. Algae production in the ARID-HV raceway was simulated with a temperature and light growth model. An energy efficient design for the ARID-HV raceway was developed.
Basgall, Lance Edgar. "Thermal energy storage design for emergency cooling". Thesis, Kansas State University, 2010. http://hdl.handle.net/2097/4637.
Texto completoDepartment of Mechanical and Nuclear Engineering
Donald L. Fenton
Emergency cooling systems are applied to any application where the loss of cooling results in damage to the product, loss of data, or equipment failure. Facilities using chilled water for cooling that experience an electrical power outage, even a small one, would cause the chiller to shut down for 20 minutes or more. If emergency cooling is not available, temperatures would continue to increase to dangerous levels, potentially damaging the facility. Examples of facilities that could be protected by having emergency cooling systems are data centers, hospitals, banks, control rooms, laboratories, clean rooms, and emergency shelters among others. This project addresses the current lack of information and methods needed to correctly design emergency cooling systems. Three application uses were investigated for the possible benefits of having emergency cooling systems. The software TRNSYS was used to simulate five typical emergency cooling systems for each of the three applications. The characteristics and differences of the systems developed from the simulations were then analyzed and documented. The five systems simulated include a pressurized chilled water tank (parallel), atmospheric chilled water tank (parallel and series), low temperature chilled water tank (parallel), and ice storage tank (series). Simulations showed that low temperature chilled water tanks were less stratified than regular chilled water tanks by approximately 10%. Simulations also showed that the differences between atmospheric and pressurized tanks were negligible. Each tank discharged energy in the same manner and managed to replenish itself in the same amount of time. Examination of the different system configurations showed that tanks in series with the thermal load have issues with recharging due to its inability to isolate itself from the thermal load. It was also observed that while low temperature chilled water and ice storage tanks had the potential of reducing the storage tank volume, the amount of time ragged cooling will last is decreased by at least a factor of two. The examination of the five systems produced the desired design methodologies needed to address the lack of information on emergency cooling systems. With the reported information designers can effectively engineer systems to meet their needs.
Soner, Ilker. "Utilization Of Fluidized Bed Combustion Ashes As Raw Material In The Production Of A Special Cement". Master's thesis, METU, 2009. http://etd.lib.metu.edu.tr/upload/12610651/index.pdf.
Texto completoC for various holding times. The results of chemical and mineralogical analysis as well as microscopic examination reveal that FBC ashes have the potential to be used in the raw meal due to the presence of characteristic mineral phases of this type of cements, i.e. yeelimite, larnite, ferrite and anhydrite, in the sample obtained at optimum sintering temperature of 1250 °
C for 60 min.
Dogruoz, Cihan. "Effect Of Pick Blunting On Cutting Performance For Weak Moderate Rocks". Phd thesis, METU, 2010. http://etd.lib.metu.edu.tr/upload/12612614/index.pdf.
Texto completoas the limiting specific energy above which poor cutting performance occurs. Nine prediction models have been developed by statistical analysis to estimate the laboratory cutting specific energy from various rock properties and wear rates.
Kusyilmaz, Ahmet. "Finite Element Study On Local Buckling And Energy Dissipation Of Seismic Bracing". Master's thesis, METU, 2008. http://etd.lib.metu.edu.tr/upload/12609662/index.pdf.
Texto completohowever, it is now possible to conduct finite element simulation of brace components using personal computers. A finite element study has been undertaken to evaluate the aforementioned limits for pin-ended pipe section steel braces. Fifty four tubular pipe brace models possessing different diameter-to-thickness ratios varying from 5 to 30 and slenderness ratios varying from 40 to 200 were analyzed. The effect of cyclic hardening modulus on the response of braces was explored. In all analysis, the models were subjected to reversed cyclic displacements up to ten times the yield displacement. Local buckling was traced during the loading history using a criterion based on local strains. Results are presented in terms of the ductility level attained by the member at the onset of local buckling. It is shown that local buckling of the section is influenced by the diameter-to-thickness and the slenderness ratios of the member. Moreover, the amount of hardening modulus was found to affect the local buckling response significantly. The need to include this material property into seismic provisions is demonstrated. Finally, the hysteretic energy dissipated by the member was quantified for each displacement excursion.
Blush, Aaron. "Impact of ASHRAE standard 189.1-2009 on building energy efficiency and performance". Kansas State University, 2010. http://hdl.handle.net/2097/6909.
Texto completoDepartment of Architectural Engineering and Construction Science
Fred L. Hasler
The purpose of this report is to provide an introduction to the new ASHRAE Standard 189.1-2009, Standard for the Design of High-Performance Green Buildings. The report will include an overview of the standard to detail what the purpose, scope and requirements for high-performance buildings will be. The entire standard will be overviewed, but the focus of this paper is in the areas of energy efficiency and building performance. Next, the report will examine further impacts that the standard will have on the building design and construction industry. Chapter 3 includes the impact on other standards, specification writing and coordination of the design and construction teams. A case study of an office building is performed to compare a baseline building meeting ASHRAE Standard 90.1 to a building meeting the minimum standards of ASHRAE Standard 189.1. The case study compares the total annual energy use of the two projects to determine an expected energy savings. Based on this information, recommendations about the new standard will be discussed. Universities and government entities should require ASHRAE Standard 189.1 for new construction projects, to show willingness to provide sustainability in buildings. Finally, conclusions about how the standard will change and impact industry will be addressed. These conclusions will include issues with adopting ASHRAE Standard 189.1 as code as well as discussion on the LEED rating system.
Acun, Bora. "Energy Based Seismic Performance Assessment Of Reinforced Concrete Columns". Phd thesis, METU, 2010. http://etd.lib.metu.edu.tr/upload/12611728/index.pdf.
Texto completoOzkaya, Cenan. "Development Of A New Seismic Isolator Named". Phd thesis, METU, 2010. http://etd.lib.metu.edu.tr/upload/12612712/index.pdf.
Texto completobased seismic isolator type on the basis of the idea that the damping of a conventional annular elastomeric bearing (EB) can be increased by filling its central core with small diameter steel balls, which dissipate energy via friction inside the confined hole of the bearing during their movements under horizontal loads. The proposed bearing type is called &ldquo
Ball Rubber Bearing (BRB)&rdquo
. A large set of BRBs with different geometrical and material properties are manufactured and tested under reversed cyclic horizontal loading at different vertical compressive load levels. Effect of supplementary confinement in the central hole of the bearing to performance of BRB is studied by performing some additional tests. Test results are used to develop design equations for BRB. A detailed non-linear finite element model is developed to verify the test results. The proposed analytical model is determined to simulate the structural hysteretic behaviour of the bearings. In design of BRBs, the proposed design guideline can be used in conjunction with the proposed non-linear finite element analysis. Extensive test results indicate that steel balls do not only increase the energy dissipation capacity of the elastomeric bearing (EB) but also increase its horizontal and vertical stiffness. It is also observed that the energy dissipation capacity of a BRB does not degrade as the number of loading cycles increases, which indicates remarkably reliable seismic performance.
Peña, Duque Leidy E. "Acid-functionalized nanoparticles for hydrolysis of lignocellulosic feedstocks". Thesis, Kansas State University, 2009. http://hdl.handle.net/2097/2201.
Texto completoDepartment of Biological and Agricultural Engineering
Donghai Wang
Acid catalysts have been successfully used for pretreatment of cellulosic biomass to improve sugar recovery and its later conversion to ethanol. However, use of acid requires a considerable equipment investment as well as disposal of residues. Acid-functionalized nanoparticles were synthesized for pretreatment and hydrolysis of lignocellulosic biomass to increase conversion efficiency at mild conditions. Advantages of using acid-functionalized metal nanoparticles are not only the acidic properties to catalyze hydrolysis and being small enough to penetrate into the lignocellulosic structure, but also being easily separable from hydrolysis residues by using a strong magnetic field. Cobalt spinel ferrite magnetic nanoparticles were synthesized using a microemulsion method and then covered with a layer of silica to protect them from oxidation. The silanol groups of the silica serve as the support of the sulfonic acid groups that were later attached to the surface of the nanoparticles. TEM images and FTIR methods were used to characterize the properties of acid-functionalized nanoparticles in terms of nanoparticle size, presence of sulfonic acid functional groups, and pH as an indicator of acid sites present. Citric acid-functionalized magnetite nanoparticles were also synthesized and evaluated. Wheat straw and wood fiber samples were treated with the acid supported nanoparticles at 80°C for 24 h to hydrolyze their hemicellulose fraction to sugars. Further hydrolysis of the liquid fraction was carried out to account for the amount of total solubilized sugars. HPLC was used to determine the total amount of sugars obtained in the aqueous solution. The perfluroalkyl-sulfonic acid functional groups from the magnetic nanoparticles yielded significantly higher amounts of oligosaccharides from wood and wheat straw samples than the alkyl-sulfonic acid functional groups did. More stable fluorosulfonic acid functionalized nanoparticles can potentially work as an effective heterogeneous catalyst for pretreatment of lignocellulosic materials.
Sari, Ibrahim. "Design, Fabrication And Implementation Of A Vibration Based Mems Energy Scavenger For Wireless Microsystems". Phd thesis, METU, 2008. http://etd.lib.metu.edu.tr/upload/12610096/index.pdf.
Texto completo8×
6 mm3, and it has been shown that 0.67 mV of voltage and 56 pW of power output can be obtained from a single cantilever of this design at a vibration frequency of 3.45 kHz. The second type generator aims to increase the bandwidth of the traditional designs by implementing cantilevers with varying length. This generator is sized 14×
12.5×
8 mm3, and the mechanical design and energy generation concept is similar to the first design. The test results show that by using 40 cantilevers with a length increment of 3 &
#956
m, the overall bandwidth of the generator can be increased to 1000 Hz. It has also been shown that 9 mV of constant voltage and 1.7 nW of constant power output can be obtained from the overall device in a vibration frequency range of 3.5 to 4.5 kHz. The third type is a standard large mass coil type generator that has been widely used in the literature. In this case, the generator is composed of a stationary base with a coil and a magnet-diaphragm assembly capable of resonating with vibrations. The fabricated device has dimensions of 8.5×
7×
2.5 mm3, and it has been considered in this study for benchmarking purposes only. The test results show that 0.3 mV of voltage and 40 pW of power output can be obtained from the fabricated design at a vibration frequency of 113 Hz. The final design aims to mechanically up-convert low frequency environmental vibrations of 1-100 Hz to a much higher frequency range of 2-3 kHz. This type of generator has been implemented for the first time in the literature. The generator is composed of two parts
a diaphragm-magnet assembly on the top, and 20 cantilevers that have coils connected in series at the base. The diaphragm oscillates by low frequency environmental vibrations, and catches and releases the cantilevers from the tip points where magnetic nickel (Ni) areas are deposited. The released cantilevers then start decaying out oscillations that is at their damped natural frequency of 2-3 kHz. It has been shown with tests that frequency up-conversion is realized in micro scale. The fabricated device has dimensions of 8.5×
7×
2.5 mm3, and a maximum voltage and power output of 0.57 mV and 0.25 nW can be obtained, respectively, from a single cantilever of the fabricated prototype at a vibration frequency of 113 Hz.
Yan, Zuanhong. "Control of fluctuating renewable energy sources : energy quality & energy filters". Thesis, University of Birmingham, 2018. http://etheses.bham.ac.uk//id/eprint/8568/.
Texto completoYang, Xiangxin. "Sol-gel synthesized nanomaterials for environmental applications". Diss., Manhattan, Kan. : Kansas State University, 2008. http://hdl.handle.net/2097/884.
Texto completoPalmer, James Dirk. "Vibrational energy flow in structures". Thesis, University of Nottingham, 1994. http://eprints.nottingham.ac.uk/28481/.
Texto completoPapafragrou, Anastasios. "Urban carbon and energy analysis : calculation of energy flows and emissions from residential housing clusters and assessment of sustainable energy options". Thesis, University of Southampton, 2010. https://eprints.soton.ac.uk/210375/.
Texto completoMa, Yingnan. "Intelligent energy management system : techniques and methods". Thesis, City University London, 2011. http://openaccess.city.ac.uk/1212/.
Texto completoMackay, Edward B. L. "Wave energy resource assessment". Thesis, University of Southampton, 2009. https://eprints.soton.ac.uk/79448/.
Texto completoMonir, Habib Saeed. "A new energy absorber for earthquake resistant buildings". Thesis, City University London, 2001. http://openaccess.city.ac.uk/8283/.
Texto completoRibeaux, Michael. "Energy absorbtion capability of damage affected composite structures". Thesis, University of Nottingham, 2003. http://eprints.nottingham.ac.uk/13040/.
Texto completoAkena, p'Ojok Robert. "Improving road transport energy efficiency through driver training". Thesis, University of Birmingham, 2014. http://etheses.bham.ac.uk//id/eprint/5275/.
Texto completoBarrett, Emily Lord. "The Investigation and Optimization of a Two-Heat-Pump System Incorporating Thermal Storage for Shaping Residential Heating Load". PDXScholar, 2016. http://pdxscholar.library.pdx.edu/open_access_etds/3025.
Texto completoOoi, Chia Ai. "Balancing control for grid-scale battery energy storage systems". Thesis, Cardiff University, 2016. http://orca.cf.ac.uk/93020/.
Texto completoFarshad, Mehr A. "Determination of design of optimal actuator location based on control energy". Thesis, City, University of London, 2018. http://openaccess.city.ac.uk/19115/.
Texto completoJohnson, Benjamin Michael Carver. "Computational Fluid Dynamics (CFD) modelling of renewable energy turbine wake interactions". Thesis, University of Central Lancashire, 2015. http://clok.uclan.ac.uk/12120/.
Texto completoSaleh, Ahmed. "Enhancement of the IEEE 802.15.4 standard by energy efficient cluster scheduling". Thesis, University of Huddersfield, 2015. http://eprints.hud.ac.uk/id/eprint/28530/.
Texto completoRoberts, Joseph. "Synthesis and characterisation of nanoscale oxides for energy applications". Thesis, University of Liverpool, 2014. http://livrepository.liverpool.ac.uk/2005979/.
Texto completoRowe, Geoffrey Michael. "Application of the dissipated energy concept to fatigue cracking in asphalt pavements". Thesis, University of Nottingham, 1996. http://eprints.nottingham.ac.uk/11888/.
Texto completoBailey, D. A. "The effect of damage on the energy absorption potential of composite structures". Thesis, University of Nottingham, 2005. http://eprints.nottingham.ac.uk/13560/.
Texto completoHashim, Hasan. "Full-spectrum solar energy harvesting using nanotechnology-enabled photovoltaic/thermoelectric hybrid system". Thesis, Cardiff University, 2015. http://orca.cf.ac.uk/87143/.
Texto completoVincent, Timothy A. "Development of a handheld breath analyser for the monitoring of energy expenditure". Thesis, University of Warwick, 2017. http://wrap.warwick.ac.uk/93856/.
Texto completoBao, Minxi. "Structural and functional integrity of energy-efficiency glazing units". Thesis, University of Birmingham, 2014. http://etheses.bham.ac.uk//id/eprint/5289/.
Texto completoCemesova, Alexandra. "Enhancing BIM-based data transfer to support the design of low energy buildings". Thesis, Cardiff University, 2013. http://orca.cf.ac.uk/57565/.
Texto completoBottome, Kristofer John. "The energy absorption of damaged braided and non-crimp fibre composite material structures". Thesis, University of Nottingham, 2006. http://eprints.nottingham.ac.uk/10173/.
Texto completoDe, Almeida Katia Campos. "A general parametric optimal power flow". Thesis, McGill University, 1994. http://digitool.Library.McGill.CA:80/R/?func=dbin-jump-full&object_id=28660.
Texto completoThis thesis presents an algorithm which uses the parameters existing in the OPF problem to find its solution. These parameters can be in the objective function or the equality or inequality constraints. This algorithm is applied to a parameterized OPF model built according to the following criteria: (i) when all parameters present in the model are relaxed from their given levels, a solution can be trivially found for this parameterized problem and (ii) when all parameters are returned to their original values, the parameterized model is equal to the original OPF. As the initially relaxed parameters are returned to their original values, they define a sequence of OPF problems which converge to the original one. The algorithm is designed to track the optimal solutions of these intermediate problems until the optimum of the original OPF. This tracking is made in a systematic manner. By using a binary search or a linear prediction method, the algorithm finds the maximum increment of the parameters which allow only one inequality to be fixed at its limit or to be released. The parameters are then adjusted to their new values, defining a new OPF problem with known optimal active feasible set. As a consequence, the optimal solution of this new problem can be easily found by solving the first order optimality conditions by Newton's method. In this way, the optimum is tracked from one active feasible set to the next until the parameters reach their original values.
The parameterization permits the solution of the OPF problem for a fixed and variable load using the same mechanism described in the previous paragraph. As a result of this systematic tracking, the method is robust and able to provide a very good insight about the behaviour of the OPF solutions. In addition, the main difficulties encountered in solving the OPF problem are easily visualized and, in particular, the approach permits the differentiation of the potential causes for the failure of the tracking process, including the identification of unsolvable cases. The sensitivities of the optimal solution as a function of the parameters are also by-products of the method; including the Bus Incremental Costs and the System Incremental Cost as functions of the loads. The approach is also flexible enough to permit the simulation of line contingencies and of Flexible AC Transmission Systems (FACTS devices). The algorithm developed was tested in numerous networks with different objective functions and initializations and the results demonstrated the potential of this technique.
Aziz, Alia Ruzanna. "The energy-absorbing characteristics of novel tube-reinforced sandwich structures". Thesis, University of Liverpool, 2015. http://livrepository.liverpool.ac.uk/2037907/.
Texto completoAbobghala, Abdelmenem. "Assessing the energy efficiency of railway vehicles with wheelset active control". Thesis, University of Huddersfield, 2018. http://eprints.hud.ac.uk/id/eprint/34756/.
Texto completoFok, Alan Tat-Kuen. "A contribution to the analysis of energy losses in transient pipe flow". Thesis, University of Ottawa (Canada), 1987. http://hdl.handle.net/10393/5421.
Texto completoEmeakaroha, Anthony. "Energy conservation through product integrated persuasive feedback using smart sensors in a university campus". Thesis, University of Kent, 2014. https://kar.kent.ac.uk/48985/.
Texto completoAldossary, Naief. "Domestic sustainable and low energy design in hot climatic regions". Thesis, Cardiff University, 2015. http://orca.cf.ac.uk/70748/.
Texto completoJayan, Bejay. "Real-time Multi-scale Smart Energy Management and Optimisation (REMO) for buildings and their district". Thesis, Cardiff University, 2016. http://orca.cf.ac.uk/99480/.
Texto completoElsayed, Hatim Ibrahim. "Utility applications of smart online energy systems : a case for investing in online power electronics". Thesis, City University London, 2014. http://openaccess.city.ac.uk/12238/.
Texto completoMarian, Laurentiu. "The tuned mass damper inerter for passive vibration control and energy harvesting in dynamically excited structural systems". Thesis, City University London, 2016. http://openaccess.city.ac.uk/14884/.
Texto completoRamlan, Roszaidi. "Effects of non-linear stiffness on performance of an energy harvesting device". Thesis, University of Southampton, 2009. https://eprints.soton.ac.uk/69588/.
Texto completoPitié, Frédéric. "High temperature thermal energy storage : encapsulated phase change material particles : determination of thermal and mechanical properties". Thesis, University of Warwick, 2012. http://wrap.warwick.ac.uk/57108/.
Texto completoShan, Jian. "Application of the sub-region mixed energy principle to numerical modelling of prestressed clad cable nets". Thesis, University of Warwick, 1990. http://wrap.warwick.ac.uk/107966/.
Texto completoDoerffel, Dennis. "Testing and characterisation of large high-energy lithium-ion batteries for electric and hybrid electric vehicles". Thesis, University of Southampton, 2007. https://eprints.soton.ac.uk/47951/.
Texto completo