Relevant bibliographies by topics / Zkouška tvrdosti

Contents

  1. Dissertations / Theses

Academic literature on the topic 'Zkouška tvrdosti'

Author: Grafiati
Published: 28 June 2021
Last updated: 11 February 2022

Create a spot-on reference in APA, MLA, Chicago, Harvard, and other styles

Select a source type:

Consult the lists of relevant articles, books, theses, conference reports, and other scholarly sources on the topic 'Zkouška tvrdosti.'

Next to every source in the list of references, there is an 'Add to bibliography' button. Press on it, and we will generate automatically the bibliographic reference to the chosen work in the citation style you need: APA, MLA, Harvard, Chicago, Vancouver, etc.

You can also download the full text of the academic publication as pdf and read online its abstract whenever available in the metadata.

Dissertations / Theses on the topic "Zkouška tvrdosti"

1

Stodola, Martin. "Stanovení mechanických vlastností materiálů svarového spoje na základě měření tvrdosti." Doctoral thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2016. http://www.nusl.cz/ntk/nusl-234833.

Full text
Abstract:
This dissertation thesis deals with determination of the mechanical properties of weld materials based on instrumented hardness test. This work was caused by the research project between IAM Brno Ltd and CEZ corp., when the task was to develop a methodology for evaluation of mechanical material properties using NDT methods. For these reasons the development of methodology is reflected especially for use in practice focusing to determining the mechanical properties of the heterogeneous weld joint on the assembled equipment. The mechanical material properties are determined by carrying out non-destructive tests of the instrumented Vickers hardness. The developed methodology for determining of basic mechanical properties is based on the principle of inverse FEM modeling of the instrumented hardness tests, when output of the testing is indentation curve and measured surface imprint after unloading. The basic material mechanical properties are achieved by comparing the outputs of the experimental instrumented hardness tests and the outputs of the modeled hardness test using FEM.
APA, Harvard, Vancouver, ISO, and other styles
2

Jiroušek, Jan. "Analýza mechanických vlastností plastových vzorků zhotovených technologií 3D tisku." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2021. http://www.nusl.cz/ntk/nusl-444289.

Full text
Abstract:
The master's thesis deals with the determination of mechanical properties of materials used for 3D printing (PLA, PETG, ABS, ASA). The theoretical part contains characteristics of polymer materials and describes testing of mechanical properties and additive technologies. In the experimental part, the standardized samples produced by the technology Fused Filament Fabrication were analysed using mechanical tests (tensile test and hardness test). Some of the examples were exposed to the selected factors of degradation. Selected parameters from mechanical testing (tensile strength, modulus of elasticity in tension, elongation and Shore hardness) were statistically processed. The conclusion of the thesis evaluates the impact of the factors of degradation on particular materials and compares them subsequently.
APA, Harvard, Vancouver, ISO, and other styles
3

Sýkora, Milan. "Analýza mechanických vlastností bimetalových materiálů s cladovanou vrstvou Inconelu." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2020. http://www.nusl.cz/ntk/nusl-417099.

Full text
Abstract:
This diploma thesis deals with the analysis of mechanical properties of bimetallic materials with clad layer of Inconel. In the theoretical part of the work there is an analysis of the investigated bimetallic material. The following is a description of mechanical tests and methods for evaluating the integrity of the surface, which were used to determine the properties of bimetallic material. The experimental part focuses on individual tests of mechanical properties of the material. For each test, the procedure for the production of test specimens, a description of the test equipment, the performance of the tests, the evaluation of the data obtained and finally, the evaluation of the results obtained are given.
APA, Harvard, Vancouver, ISO, and other styles
4

Ivánek, Radim. "Rozměrová, tvarová a materiálová analýza bimetalových dílců s definovaným poloměrem ohybu." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2020. http://www.nusl.cz/ntk/nusl-417100.

Full text
Abstract:
The thesis aim is an evaluation of achieved results coming from the analysis of pipe bend 180° for the critical bending / bend 1D and supercritical bending / bend 0,7D. The theoretical part is focused on material property of a bimetallic pipe and on methods applied to work out the analysis. The definition of critical points at a considered segment and possible defects arisen while bending is embodied in the thesis. The practical part of the thesis is based on presenting dimensional and proportional analysis based on using optical microscopes and 3D scanner GOM ATOS. The material analysis was aimed at macrostructure as well as microstructure of the bimetallic pipe material, at chemical composition and at the hardness when low-loaded. The analysis achieved results are assessed at the end of the thesis.
APA, Harvard, Vancouver, ISO, and other styles
5

Wasserbauer, Jaromír. "Lokální zkoušky mechanických vlastností materiálů." Master's thesis, Vysoké učení technické v Brně. Fakulta chemická, 2009. http://www.nusl.cz/ntk/nusl-216510.

Full text
Abstract:
This thesis deals with measurement of hardness and microhardness in relation to structure of homogeneous and heterogeneous materials. In the introduction basic theoretical background is commented, i.e. definitions, terminology, principles of measuring techniques for estimation of hardness, microhardness, tensile strength, compressive strength and bending strength. Follows a brief review of present research results focused on use of described principles in materials engineering. Then the experimental equipment and sample preparation is described. The crucial part of the thesis is summary of achieved results of original measurement and discussion of their relations to each other. Finally, the groundbreaking estimation is described, showing the correlation of chemical composition gradient and mechanical properties in interfacial zone of geopolymeric material.
APA, Harvard, Vancouver, ISO, and other styles
6

Svozil, Libor. "Mechanicko-strukturní charakteristiky slitiny hořčíku AZ61." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2010. http://www.nusl.cz/ntk/nusl-229290.

Full text
Abstract:
Microstructure and mechanical properties of AZ61 magnesium alloy in cast condition and after solution annealing were compared. The compare of mechanical properties of alloy, their hardness and microanalysis of occurring phases are included in this work. For compare has been used a light microscopy, tensile test, hardness measurements and scanning electron microscopy.
APA, Harvard, Vancouver, ISO, and other styles
7

Virágová, Tereza. "Porovnání různých metod stanovení melitelnosti práškových pojiv." Master's thesis, Vysoké učení technické v Brně. Fakulta stavební, 2017. http://www.nusl.cz/ntk/nusl-295662.

Full text
Abstract:
The aim of this thesis is to summarize the knowledge gained in the field of grinding medium-hard and hard materials. Work has focused on examining the grindability of the material using available laboratory mill. The part of the work is subsequent optimization of the grinding process on the device and evaluation of the results.
APA, Harvard, Vancouver, ISO, and other styles
8

Vlk, Václav. "Mechanické vlastnosti a lomové chování svarových spojů a základních materiálů přívodního potrubí vodní turbíny." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2014. http://www.nusl.cz/ntk/nusl-231314.

Full text
Abstract:
The master thesis is focussed on evaluation of mechanical properties and fracture behaviour of basic materials and weld joints of a water turbine supply pipe. The results of tensile tests, fracture toughness tests, hardness and micro-hardness tests and further chemical and metallography analysis are used for operating degradation level evaluation of the construction material and also for a residual operating recognition of the second, identical specimen of supply pipe.
APA, Harvard, Vancouver, ISO, and other styles
9

Snížek, Petr. "Změny vnitřní stavby klastických sedimentárních hornin při zkoušce Schmidtovým kladivem." Master's thesis, 2013. http://www.nusl.cz/ntk/nusl-321071.

Full text
Abstract:
iv Summary Schmidt hammer is the instrument which is used for the assessment of rock mechanical properties and this instrument is classified as the indirect method. This method is based on the assessment of rebound value (R) of the Schmidt hammer, which is measurred by the amount of rebound of the impact plunger from the surface of tested rock. Schmidt hammer is called as the non-destructive method of rock assessment and it is called as in situ testing method as well. The main objective of this work is provement, that Schmidt hammer testing is destructive method and define degree of damage which is caused in the rock mass. Sedimentary rocks were used for the testing, mostly sandstones and arkose sandstones with different types of cement. This made it possible to test the fraction of the rock mass and the relation between fraction and type of cement. The clasts of the rocks had different properties than it was possible to find the relation between grain size and fraction of the rock. Already in procedure of the testing by Schmidt hammer it was obvious, that this metod is definitely destructive. Rock surface after hitting by plunger of Schmidt hammer gains macroscopically observeable destruction. On the surface is the circular track of the plunger and the surface is grinded. It is possible to wipe the small...
APA, Harvard, Vancouver, ISO, and other styles
We offer discounts on all premium plans for authors whose works are included in thematic literature selections. Contact us to get a unique promo code!

To the bibliography