Dissertations / Theses: 'Wind energy conversion systems – Canada'

1

Buehrle, Bridget Erin. "Modeling of Small-Scale Wind Energy Conversion Systems." Thesis, Virginia Tech, 2013. http://hdl.handle.net/10919/50920.

Full text

Abstract:

As wind turbines are increasingly being adopted for meeting growing energy needs, their implementation for personal home use in the near future is imminent. There are very few studies conducted on small-scale turbines in the one to two meter diameter range because the power generated at this scale is currently not sufficient to justify the cost of installation and maintenance. The problem is further complicated by the fact that these turbines are normally mounted at low altitudes and thus there is necessity to have the optimum operating regime in the wind speed range of 3-10 mph (1.34 -- 4.47 m/s). This thesis discusses two methods for increasing the efficiency of horizontal axis small-scale wind energy conversion systems, 1) adding a diffuser to increase the wind speed at the rotor and 2) designing tubercles to enhance the flow characteristics over blades. Further, it was identified during the course of thesis that for simple installation and maintenance in the residential areas vertical axis turbines are advantageous. Thus, the second chapter of this thesis addresses the design of vertical axis turbines with power generation capability suitable for that of a typical US household.
    The study of the diffuser augmented wind turbine provides optimum dimensions for achieving high power density that can address the challenges associated with small scale wind energy systems; these challenges are to achieve a lower start-up speed and low wind speed operation. The diffuser design was modeled using commercial computational fluid dynamics code. Two-dimensional modeling using actuator disk theory was used to optimize the diffuser design. A statistical study was then conducted to reduce the computational time by selecting a descriptive set of models to simulate and characterize relevant parameters\' effects instead of checking all the possible combinations of input parameters. Individual dimensions were incorporated into JMP® software and randomized to design the experiment. The results of the JMP® analysis are discussed in this paper. Consistent with the literature, a long outlet section with length one to three times the diameter coupled with a sharp angled inlet was found to provide the highest amplification for a wind turbine diffuser.
    The second study consisted of analyzing the capabilities of a small-scale vertical axis wind turbine. The turbine consisted of six blades of extruded aluminum NACA 0018 airfoils of 0.08732 m (3.44 in) in chord length. Small-scale wind turbines often operate at Reynolds numbers less than 200,000, and issues in modeling their flow characteristics are discussed throughout this thesis. After finding an appropriate modeling technique, it was found that the vertical axis wind turbine requires more accurate turbulence models to appropriately discover its performance capabilities.
    The use of tubercles on aerodynamic blades has been found to delay stall angle and increase the aerodynamic efficiency. Models of 440 mm (17.33 in) blades with and without tubercles were fabricated in Virginia Tech\'s Center for Energy Harvesting Materials and Systems (CEHMS) laboratory. Comparative analysis using three dimensional models of the blades with and without the tubercles will be required to determine whether the tubercle technology does, in fact, delays the stall. Further computational and experimental testing is necessary, but preliminary results indicate a 2% increase in power coefficient when tubercles are present on the blades.

Master of Science

APA, Harvard, Vancouver, ISO, and other styles

2

Trilla, Romero Lluís. "Power converter optimal control for wind energy conversion systems." Doctoral thesis, Universitat Politècnica de Catalunya, 2013. http://hdl.handle.net/10803/134602.

Full text

Abstract:

L'energia eòlica ha incrementat la seva presència a molts països i s'espera que tingui encara un pes més gran en la generació elèctrica amb la implantació de la tecnologia eòlica marina. En aquest context el desenvolupament de models dels Sistemes de Generació per Turbina de Vent (SGTV) precisos és important pels operadors de xarxa per tal d'avaluar-ne el comportament. Els codis de xarxa ofereixen un seguit de normes per validar models amb dades obtingudes de proves de camp. A la primera part d'aquesta tesi un model de SGTV amb màquina d'inducció doblement alimentada (DFIG) és validat d'acord amb les normatives espanyola i alemanya. Avui dia molts parc eòlics utilitzen DFIG i, en conseqüència, les dades de camp disponibles son per aquesta tecnologia. Per a la indústria eòlica marina un avanç prometedor son els SGTV amb generadors síncrons d'imants permanents (PMSG). Per aquesta raó la segona part d'aquesta tesi es centra en SGTV basats en PMSG amb convertidor back-to-back de plena potència. Aquest convertidor es pot dividir en dues parts: el costat de xarxa (GSC) que interactua amb la xarxa elèctrica i el costat de màquina (MSC) que controla el generador. En general, el sistema de control del convertidor recau en els tradicionals controladors PI i, en ocasions, incorpora desacoblaments per reduir les influencies creuades entre les variables. Aquest controlador pot ser sintonitzat i implementat fàcilment donat que la seva estructura és simple, però, no presenta una resposta ideal donat que no aprofita tots els graus de llibertat disponibles en el sistema. És important desenvolupar controladors fiables que puguin oferir una resposta previsible del sistema i proveir robustesa i estabilitat. En especial per zones on la presència eòlica és gran i per parcs eòlics connectats a xarxes dèbils. En aquest treball es proposa un sistema de control pel convertidor basat en teoria de control H-infinit i en controladors Lineals amb Paràmetres Variants (LPV). La teoria de control òptim proveeix un marc de treball on més opcions es poden tenir en consideració a l'hora de dissenyar el controlador. En concret la teoria de control H-inifinit permet crear controladors multivariables per tal d'obtenir una òptima resposta del sistema, proveir certa robustesa i assegurar l'estabilitat. Amb aquesta tècnica durant la síntesi del controlador el pitjor cas de senyals de pertorbació és contemplat, d'aquesta manera el controlador resultant robustifica l'operació del sistema. Es proposa aquest control per al GSC posant especial èmfasi en obtenir un control de baixa complexitat que mantingui els beneficis d'aplicar la teoria de control òptim i faciliti la seva implementació en computadors industrials. Pel MSC es proposa una estratègia diferent basada en control LPV donat que el punt d'operació del generador canvia constantment. El sistema de control basat en LPV és capaç d'adaptar-se dinàmicament al punt d'operació del sistema, així s'obté en tot moment la resposta definida durant el procés de disseny. Amb aquesta tècnica l'estabilitat del sistema sobre tot el rang d'operació queda garantida i, a més, s'obté una resposta predictible i uniforme. El controlador està dissenyat per tenir una estructura simple, com a resultat s'obté un control que no és computacionalment exigent i es proveeix una solució que pot ser utilitzada amb equips industrials. S'utilitza una bancada de proves que inclou el PMSG i el convertidor back-to-back per tal d'avaluar experimentalment l'estratègia de control dissenyada al llarg d'aquest treball. L'enfoc orientat a la implementació dels controls proposats facilita el seu ús amb el processador de senyals digitals inclòs a la placa de control de la bancada. Els experiments realitzats verifiquen en un ambient realista els beneficis teòrics i els resultats de simulació obtinguts prèviament. Aquestes proves han ajudat a valorar el funcionament dels controls en un sistema discret i la seva tolerància al soroll de senyals i mesures
Wind energy has increased its presence in many countries and it is expected to have even a higher weight in the electrical generation share with the implantation of offshore wind farms. Consequently, the wind energy industry has to take greater responsibility towards the integration and stability of the power grid. In this sense, there are proposed in the present work control systems that aim to improve the response and robustness of the wind energy conversion systems without increasing their complexity in order to facilitate their applicability. In the grid-side converter it is proposed to implement an optimal controller with its design based on H-infinity control theory in order to ensure the stability, obtain an optimal response of the system and also provide robustness. In the machine-side converter the use of a Linear Parameter-Varying controller is selected, this choice provides a controller that dynamically adapts itself to the operating point of the system, in this way the response obtained is always the desired one, the one defined during the design process. Preliminary analysis of the controllers are performed using models validated with field test data obtained from operational wind turbines, the validation process followed the set of rules included in the official regulations of the electric sector or grid codes. In the last stage an experimental test bench has been developed in order to test and evaluate the proposed controllers and verify its correct performance.

APA, Harvard, Vancouver, ISO, and other styles

3

Mendonca, Jose Manuel de Araujo Baptista. "Microcomputer on-line control of wind energy conversion systems." Thesis, Imperial College London, 1986. http://hdl.handle.net/10044/1/38101.

Full text

APA, Harvard, Vancouver, ISO, and other styles

4

Wu, Feng. "Modelling and control of wind and wave energy conversion systems." Thesis, University of Birmingham, 2009. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.525483.

Full text

Abstract:

The modelling and control of wind and wave energy conversion systems is carried out in this thesis. The thesis comprises two parts. The first part is focused on the modelling and control of wind conversion system while the second part is on the modelling and control of wave energy conversion system (WEe). In the first part, the small signal stability of the \\lind turbine (\VT) with doubly fed induction generator (DFIG) and the WT with direct-drive permanent magnet generator (DDPMG) an: analysed using detailed models. A parameter tuning algorithm and a nonlinear controller are proposed, respectively, to improve dynamic performance of WT with DFIG. The impacts of WT with DFIG, WT with DDPMG and WT the induction generator (lG) on power system transient stability are compared. In the second part, a new coordinate transformation is proposed for the model of Archimedes wave swing (A WS) based WEe system, the transformed model is compatible with the power system dynamic analysis. The controllers for A WS based WEe are designed so as to extract maximum power from the wave, output constant power and maintain the terminal voltage. The application of battery energy storage in smoothing the output power of WEe system is studied.

APA, Harvard, Vancouver, ISO, and other styles

5

MacRae, Angus Neil. "Economic and cost engineering aspects of wind energy conversion systems." Thesis, Robert Gordon University, 1990. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.258961.

Full text

APA, Harvard, Vancouver, ISO, and other styles

6

Macmillan, Susan. "An appraisal of wind energy conversion systems for agricultural enterprises." Thesis, Robert Gordon University, 1989. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.330282.

Full text

APA, Harvard, Vancouver, ISO, and other styles

7

Zoric, I. "Multiple three-phase induction generators for wind energy conversion systems." Thesis, Liverpool John Moores University, 2018. http://researchonline.ljmu.ac.uk/8387/.

Full text

Abstract:

During the past decade, there has been a considerable increase in the number of published works on multiphase machines and drives. This increased interest has been largely driven by a need for the so-called green energy, i.e. energy generated from renewable sources such as wind, and also an increased emphasis on greener means for transportation. Some of the advantages multiphase machines offer over three-phase counterparts are better fault tolerance, smaller current and power per phase, and higher frequency torque ripple. This thesis examines use of a multiphase induction generator in wind energy conversion systems (WECS). In particular, multiphase generators that comprise multiple 3-phase winding sets, where each winding set is supplied using an independent 3-phase voltage source inverter (VSI), are studied. It is claimed that these topologies offer advantages in cases where a WECS is connected to a multitude of independent ac or dc microgrids, systems where a single high-voltage dc link is needed or where a simple fault tolerance is achieved when a complete winding set is switched off. All of these examples require an arbitrary power or current sharing between winding sets. In order to achieve arbitrary current and power sharing, the control can be implemented using multi stator (MS) variables, so that the flux and torque producing currents of each winding set can be arbitrarily set. As an alternative, this thesis uses vector space decomposition (VSD) to implement the control, while individual winding set flux/torque producing currents are governed by finding the relationships between MS and VSD variables. This approach has all the advantages of both MS and VSD, i.e. access to individual winding set variables of MS and the ability to implement control in the multiple decoupled two dimensional subspaces of VSD, while heavy cross coupling between winding set variables, a weakness of MS, is avoided. Since the goal of the thesis is to present use of multiphase machines in WECS, modelling and simulation of a simple multiphase WECS in back-to-back configuration has been performed at first. All systems relevant to machine control where considered, such as grid and machine side VSIs, grid filter, indirect rotor field oriented control, current control in both flux/torque producing and non-producing subspaces, low order harmonic elimination, maximum power point tracking control, and voltage oriented control of the grid side VSI. Moreover, various WECS supply topologies were considered where developed current and power sharing would be a necessary requirement. Development of the proposed current sharing control commences with an analysis of multiple 3-phase machine modelling in terms of both MS and VSD variables. Since the actual control is implemented using decoupled VSD variables, VSD modelling has been studied in detail, resulting in an algorithm for creation of the VSD matrix applicable to any symmetrical or asymmetrical multiphase machine with single or multiple neutral points. Developed algorithm always decouples the machine into orthogonal two-dimensional subspaces and zero sequence components while making sure that all odd-order harmonics are uniquely mapped. Harmonic mapping analysis is offered as well. Next, relationship between MS and VSD variables has been developed by mapping MS variables into VSD subspaces. Since VSD matrix creation algorithm is valid for any multiphase machine, relationship between MS and VSD variables is applicable to any multiple 3-phase machine regardless of the configuration (symmetrical/asymmetrical), number of neutral points or machine type (synchronous or induction). Established relationship between MS and VSD has been used to implement current sharing control in decoupled VSD subspaces of the machine. It is shown that in order to achieve arbitrary current sharing it is only necessary to impose currents in flux/torque non-producing subspaces. Hence, total machine’s flux and torque are not affected at all. Besides verification by Matlab simulations, two topologies are experimentally investigated, a parallel machine side converter configuration and the case when a single high voltage dc link is created by cascading dc-links of the machine side VSIs. In the first case the ability of arbitrary current sharing between winding sets is validated, while the second tested topology demonstrates use of the developed control for the purpose of voltage balancing of the cascaded dc links.

APA, Harvard, Vancouver, ISO, and other styles

8

Li, Wenyan Kusiak Andrew. "Predictive engineering in wind energy a data-mining approach /." [Iowa City, Iowa] : University of Iowa, 2009. http://ir.uiowa.edu/etd/399.

Full text

APA, Harvard, Vancouver, ISO, and other styles

9

Diaz, Matias. "Control of the modular multilevel matrix converter for wind energy conversion systems." Thesis, University of Nottingham, 2017. http://eprints.nottingham.ac.uk/47157/.

Full text

Abstract:

The nominal power of single Wind Energy Conversion Systems has been steadily growing, reaching power ratings close to 10 MW. In the power conversion stage, medium-voltage power converters are replacing the conventional low-voltage back-to-back topology. Modular Multilevel Converters have appeared as a promising solution for Multi-MW WECSs due to their characteristics such as modularity, reliability and the capability to reach high nominal voltages. Thereby, this thesis discusses the application of the Modular Multilevel Matrix Converter to drive Multi-MW Wind Energy Conversion Systems (WECSs). The modelling and control systems required for this application are extensively analysed and discussed in this document. The proposed control strategies enable decoupled operation of the converter, providing maximum power point tracking capability at the generator-side, grid-code compliance and Low Voltage Ride Through Control at the grid-side and good steady-state and dynamic performance for balancing the capacitor voltages of the converter. The effectiveness of the proposed control strategies is validated through simulations and experimental results. Simulation results are obtained with a 10MW, 6.6 kV Modular Multilevel Matrix Converter based WECS model developed in PLECS software. Additionally, a 5 kVA downscale prototype has been designed and constructed during this Ph.D. The downscale prototype is composed of 27 H-Bridges power cells. The system is controlled using a Digital Signal Processor connected to three Field Programmable Gate Array which are equipped with 50 analogue-digital channels and 108 gate drive signals. Two programmable AMETEK power supplies emulate the electrical grid and the generator. The wind turbine dynamics is programmed in the generator-side power supply to emulate a generator operating in variable speed/voltage mode. The output port of the Modular Multilevel Matrix Converter is connected to another power source which can generate programmable grid sag-swell conditions. Simulation and experimental results for variable-speed operation, grid-code compliance, and capacitor voltage regulation have confirmed the successful operation of the Modular Multilevel Matrix Converter based WECSs. In all the experiments, the proposed control systems ensure proper capacitor voltage balancing, keeping the flying capacitor voltages bounded and with low ripple. Additionally, the performance of the generator-side and grid-side control system have been validated for Maximum Power Point Tracking and Low-Voltage Ride Through, respectively.

APA, Harvard, Vancouver, ISO, and other styles

10

Díaz, Díaz Matías David. "Control of the modular multilevel Matrix converter for wind energy conversion systems." Tesis, Universidad de Chile, 2017. http://repositorio.uchile.cl/handle/2250/147484.

Full text

Abstract:

Doctor en Ingeniería Eléctrica. Doctor of Philosophy in Electrical and Electronic Engineering
La potencia nominal de los Sistemas de Conversión de Energía Eólica se ha incrementado constantemente alcanzando niveles de potencia cercanos a los 10 MW. Por tanto, convertidores de potencia de media tensión están reemplazando a los convertidores Back-to-Back de baja tensión habitualmente empleados en la etapa de conversión de energía. Convertidores Modulares Multinivel se han posicionado como una solución atractiva para Sistemas de Conversión de Energía Eólica de alta potencia debido a sus buenas prestaciones. Algunas de estas prestaciones son la capacidad de alcanzar altos voltajes, modularidad y confiabilidad. En este contexto, esta tesis discute la aplicación del Convertidor Modular Matricial Multinivel para conectar Sistemas de Conversión de Energía Eólica de alta potencia. Los modelos matemáticos y estrategias de control requeridas para esta aplicación son descritos y discutidos en este documento. Las estrategias de control propuestas habilitan una operación desacoplada del convertidor, proporcionando seguimiento del máximo punto de potencia en el lado del generador eléctrico del sistema eólico, cumplimiento de normas de conexión en el lado de la red eléctrica y regulación de los condensadores flotantes del convertidor. La efectividad de las estrategias de control propuestas es validada a través de simulaciones y experimentos realizados con un prototipo de laboratorio. Las simulaciones se realizan con un Sistemas de Conversión de Energía Eólica de 10 MW operando a 6.6 kV. Dicho sistema se implementa en el software PLECS. Por otro, se ha desarrollado un prototipo de laboratorio de 6kVA durante el desarrollo de este proyecto. El prototipo de laboratorio considera un Convertidor Modular Matricial Multinivel de 27 módulos Puente-H . El sistema es controlado empleando una plataforma de control basada en una Digital Signal Processor conectada a tres tarjetas del tipo Field Programmable Gate Array que proveen de 50 mediciones análogo-digital y 108 señales de disparo. La entrada del convertidor es conectada a una fuente programable marca Ametek que emula el comportamiento de la turbina eólica. A su vez, la salida del convertidor es conectada a otra fuente programable con capacidad de producir fallas en la tensión. Los resultados obtenidos, tanto en el prototipo experimental como en simulación, confirman la operación exitosa del Convertidor Modular Matricial Multinivel en aplicaciones eólicas de alta potencia. En todos los casos, las estrategias de control propuestas aseguran regulación de la tensión en los condensadores flotantes, seguimiento del máximo punto de potencia en el lado del generador eléctrico del sistema eólico y cumplimiento de normas de conexión en el lado de la red eléctrica.
The nominal power of single Wind Energy Conversion Systems has been steadily growing, reaching power ratings close to 10MW. In the power conversion stage, medium-voltage power converters are replacing the conventional low-voltage back-to-back topology. Modular Multilevel Converters have appeared as a promising solution for Multi-MW WECSs due to their characteristics such as modularity, reliability and the capability to reach high nominal voltages. Thereby, this thesis discusses the application of the Modular Multilevel Matrix Converter (\mc) to drive Multi-MW Wind Energy Conversion Systems (WECSs). The modelling and control systems required for this application are extensively analysed and discussed in this document. The proposed control strategies enable decoupled operation of the converter, providing maximum power point tracking capability at the generator-side, grid-code compliance and Low Voltage Ride Through Control at the grid-side and good steady state and dynamic performance for balancing the capacitor voltages of the converter.\\ The effectiveness of the proposed control strategies is validated through simulations and experimental results. Simulation results are obtained with a 10MW, 6.6 kVM3C based WECS model developed in PLECS software. Additionally, a 5 kVA downscale prototype has been designed and constructed during this Ph.D. The downscale prototype is composed of 27 H-Bridges power cells. The system is controlled using a Digital Signal Processor connected to three Field Programmable Gate Array which are equipped with 50 analogue-digital channels and 108 gate drive signals. Two programmable AMETEK power supplies emulate the electrical grid and the generator. The wind turbine dynamics is programmed in the generator-side power supply to emulate a generator operating in variable speed/voltage mode. The output port of the M3C is connected to another power source which can generate programmable grid sag-swell conditions. Simulation and experimental results for variable-speed operation, grid-code compliance, and capacitor voltage regulation have confirmed the successful operation of the \mc{} based WECSs. In all the experiments, the proposed control systems ensure proper capacitor voltage balancing, keeping the flying capacitor voltages bounded and with low ripple. Additionally, the performance of the generator-side and grid-side control system have been validated for Maximum Power Point Tracking and Low-Voltage Ride Through, respectively.

APA, Harvard, Vancouver, ISO, and other styles

11

Hostettler, Jacob. "Advanced Control of Permanent Magnet Synchronous Generators for Variable Speed Wind Energy Conversion Systems." Thesis, Southern Illinois University at Edwardsville, 2015. http://pqdtopen.proquest.com/#viewpdf?dispub=1588620.

Full text

Abstract:

Various environmental and economic factors have lead to increased global investment in alternative energy technologies such as solar and wind power. Although methodologies for synchronous generator control are well researched, wind turbines present control systems challenges not presented by traditional generation. The varying nature of wind makes achieving synchronism with the existing electrical power grid a greater challenge. Departing from early use of induction machines, permanent magnet synchronous generators have become the focus of power systems and control systems research into wind energy systems. This is due to their self excited nature, along with their high power density. The problem of grid synchronism is alleviated through the use of high performance power electronic converters. In achievement of the optimal levels of efficiency, advanced control systems techniques oer promise over more traditional approaches. Research into sliding mode control, and linear matrix inequalities with nite time boundedness and H∞ performance criteria, when applied to the dynamical models of the system, demonstrate the potential of these control methodologies as future avenues for achieving higher levels of performance and eciency in wind energy.

APA, Harvard, Vancouver, ISO, and other styles

12

Al-Qrimli, Fadhil Abbas Mehdi. "An energy conversion scheme using a permanent magnet generator and a PWM, GTO converter." Thesis, University of Liverpool, 1991. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.304736.

Full text

APA, Harvard, Vancouver, ISO, and other styles

13

Huang, Yuansheng. "Sliding Mode Observer Design for Permanent Magnetic Synchronous Generator Based Wind Energy Conversion Systems." Thesis, Southern Illinois University at Edwardsville, 2017. http://pqdtopen.proquest.com/#viewpdf?dispub=10258376.

Full text

Abstract:

Real-time rotor position and speed information is essential for effective power control of permanent magnet synchronous generator-based wind energy conversion systems. The presence of traditional encoders can increase the size, cost and complexity, but also reduce the overall system life-time and reliability. To provide a more reliable sensorless wind generation control scheme and eliminate the reliance on encoders, this paper presents a novel high order sliding mode observer for power control of permanent magnet synchronous generator-based wind energy conversion systems. Compared with the first order sliding mode observer, a high order sliding mode observer shows superior estimation accuracy with significantly reduced chattering effect. A three-level neutral-point-clamped space vector pulse width modulation (NPC-SVPWM) based power converter is used to reduce the voltage stress on power switching devices and produce less harmonics in the output waveforms compared with a traditional two-level inverter. Computer simulation results have shown the superior performance of the purposed high order sliding mode observer in wind turbine power control applications.

APA, Harvard, Vancouver, ISO, and other styles

14

Liddle, Marshall. "Towards a better wind power map of Nevada." abstract and full text PDF (free order & download UNR users only), 2008. http://0-gateway.proquest.com.innopac.library.unr.edu/openurl?url_ver=Z39.88-2004&rft_val_fmt=info:ofi/fmt:kev:mtx:dissertation&res_dat=xri:pqdiss&rft_dat=xri:pqdiss:1453599.

Full text

APA, Harvard, Vancouver, ISO, and other styles

15

Chahwan, John A. "Vanadium-redox flow and lithium-ion battery modelling and performance in wind energy applications." Thesis, McGill University, 2007. http://digitool.Library.McGill.CA:80/R/?func=dbin-jump-full&object_id=100223.

Full text

Abstract:

As wind energy penetration levels increase, there is a growing interest in using storage devices to aid in managing the fluctuations in wind turbine output power. Vanadium-Redox batteries (VRB) and Lithium-Ion (Li-Ion) batteries are two emerging technologies which can provide power smoothing in wind energy systems. However, there is an apparent gap when it comes to the data available regarding the design, integration and operation of these batteries in wind systems. This thesis presents suitable battery electrical models which will be used to assess system performance in wind energy applications, including efficiency under various operating conditions, transfer characteristics and transient operation. A design, sizing and testing methodology for battery integration in converter based systems is presented. Recommendations for the development of operating strategies are then provided based on the obtained results.

APA, Harvard, Vancouver, ISO, and other styles

16

McCartney, Shauna. "The simulation and control of a grid-connected wind energy conversion system." Master's thesis, University of Central Florida, 2010. http://digital.library.ucf.edu/cdm/ref/collection/ETD/id/4680.

Full text

Abstract:

With the rising cost of petroleum, concerns about exhausting the fossil fuels we depend on for energy, and the subsequent impacts that the burning of these types of fuels have on the environment, countries around the world are paying close attention to the development of renewable types of energy. Consequently, researchers have been trying to develop ways to take advantage of different types of clean and renewable energy sources. Wind energy production, in particular, has been growing at an increasingly rapid rate, and will continue to do so in the future. In fact, it has become an integral part in supplying our future energy needs, making further advancements in the field exceedingly critical. A 2 MW wind energy conversion system (WECS) is presented and has been simulated via the dynamic simulation software Simulink. This WECS consists of a 2 MW permanent magnet synchronous generator connected to the transmission grid through a power conversion scheme. The topology of this converter system consists of a passive AC/DC rectifier as well as a PWM DC/AC IGBT inverter, used to interface the DC link with the grid. The inverter has an integrated current control system for power factor correction to improve output power stability. The described WECS enhances grid-side tolerance by buffering wind power disturbances demonstrated by its capability to isolate the grid from wind speed fluctuations. It also optimizes wind energy capture through harmonic filtering, enhancing output power quality. These findings have the potential to lead to further advancements including the capability for island operation and integration to a smart grid.
ID: 029050708; System requirements: World Wide Web browser and PDF reader.; Mode of access: World Wide Web.; Thesis (M.S.E.E.)--University of Central Florida, 2010.; Includes bibliographical references (p. 66-70).
M.S.E.E.
Masters
Department of Electrical Engineering and Computer Science
Engineering and Computer Science

APA, Harvard, Vancouver, ISO, and other styles

17

Agabus, Hannes. "Large-scale integration of wind energy into the power system considering the uncertainty information = Elektrituulikute integreerimine energiasüsteemi arvestades informatsiooni mittetäielikkust /." Tallinn : TUT Press, 2009. http://digi.lib.ttu.ee/i/?446.

Full text

APA, Harvard, Vancouver, ISO, and other styles

18

Palmer, Nathan Reed. "Smart Composites evaluation of embedded sensors in composite materials /." Thesis, Montana State University, 2009. http://etd.lib.montana.edu/etd/2009/palmer/PalmerN0809.pdf.

Full text

Abstract:

As an emerging form of renewable energy, horizontal wind turbines have experienced advancements in improving efficiency and reliability. These advances have pushed the limits of current technology used in wind turbines. Smart blades have been proposed as a method of addressing these limitations. Sensor integration within blade construction is the first step in development of smart blades. Thus, several low cost sensors were chosen, 1 axis strain gages, polyvinylidene fluoride films (PVDF), and single mode fiber optics either coated in acrylate or polyimide. To ensure successful bonding between sensor and composite two surface treatment techniques were developed. The first, dipping of the sensor into a bath of 20% by weight solution of nitric acid and the second was submersion of the sensor in the nitric acid for ten seconds prior to removal. These treatments were compared against sensors not surface treated prior to embedding. These sensors were embedded within samples created of fiberglass and epoxy or vinyl ester resin. Two different material tests were conducted. Tensile testing allowed for evaluation of sensor sensitivity, sensor failure point, material tensile modulus, and material tensile strength. Mode I fracture toughness evaluation, indicated the level of successful bonding which occurred during resin curing. Field Emission Scanning Electron Microscopy (FESEM) was conducted to further confirm the level of bonding between resin and sensor, post fracture. Results for embedded strain gages showed an adverse effect for vinyl ester samples. Epoxy samples fared better, thus concluding manufacturing success for epoxy samples, submersion being preferred, and alternative methods needed for vinyl ester samples. PVDF films had good qualitative FESEM images combined with increasing trends. It was concluded that integration for both resin groups with sensors submerged in nitric acid was successful. Fiber optics coated in acrylate also showed good bonding under FESEM imaging as well as testing. It was thus concluded that submersion was the preferred treatment. Lastly, fiber optics coated in polyimide embedded in vinyl ester composites showed significant drawbacks and it was concluded that alternative methods need exploration. Those embedded in epoxy were successfully integrated and submersion in nitric acid showed the most potential.

APA, Harvard, Vancouver, ISO, and other styles

19

Currin, Hugh D. "A dynamic prescribed vortex wake model for the FAST/AeroDyn wind energy conversions simulation code." abstract and full text PDF (free order & download UNR users only), 2007. http://0-gateway.proquest.com.innopac.library.unr.edu/openurl?url_ver=Z39.88-2004&rft_val_fmt=info:ofi/fmt:kev:mtx:dissertation&res_dat=xri:pqdiss&rft_dat=xri:pqdiss:3258834.

Full text

APA, Harvard, Vancouver, ISO, and other styles

20

Hamilton, Nicholas Michael. "Anisotropy of the Reynolds Stress Tensor in the Wakes of Counter-Rotating Wind Turbine Arrays." PDXScholar, 2014. https://pdxscholar.library.pdx.edu/open_access_etds/1848.

Full text

Abstract:

A wind turbine array was constructed in the wind tunnel at Portland State University in a standard Cartesian arrangement. Configurations of the turbine array were tested with rotor blades set to rotate in either a clockwise or counter-clockwise sense. Measurements of velocity were made with stereo particle-image velocimetry. Mean statistics of velocities and Reynolds stresses clearly show the effect of direction of rotation of rotor blades for both entrance and exit row turbines. Rotational sense of the turbine blades is visible in the mean spanwise velocity W and the Reynolds shear stress -[macron over vw]. The normalized anisotropy tensor was decomposed yielding invariants [lowercase eta] and [lowercase xi], which are plotted onto the Lumley triangle. Invariants of the normalized Reynolds stress anisotropy tensor indicate that distinct characters of turbulence exist in regions of the wake following the nacelle and the rotor blade tips. Eigendecomposition of the tensor yields principle components and corresponding coordinate system transformations. Characteristic spheroids are composed with the eigenvalues from the decomposition yielding shapes predicted by the Lumley triangle. Rotation of the coordinate system defined by the eigenvectors demonstrates streamwise trends, especially trailing the top rotor tip and below the hub of the rotors. Direction of rotation of rotor blades is evidenced in the orientation of characteristic spheroids according to principle axes. The characteristic spheroids of the anisotropy tensor and their relate alignments varies between cases clearly seen in the inflows to exit row turbines. There the normalized Reynolds stress anisotropy tensor shows cumulative effects of the rotational sense of upstream turbines. Comparison between the invariants of the Reynolds stress anisotropy tensor and terms from the mean mechanical energy equation indicate a correlation between the degree of anisotropy and the regions of the wind turbine wakes where turbulence kinetic energy is produced. The flux of kinetic energy into the momentum-deficit area of the wake from above the canopy is associated with prolate characteristic spheroids. Flux upward into the wake from below the rotor area is associate with oblate characteristic spheroids. Turbulence in the region of the flow directly following the nacelle of the wind turbines demonstrates more isotropy compared to the regions following the rotor blades. The power and power coefficients for wind turbines indicate that flow structures on the order of magnitude of the spanwise turbine spacing that increase turbine efficiency depending on particular array configuration.

APA, Harvard, Vancouver, ISO, and other styles

21

Kuiler, Ian Radcliffe. "Condition monitoring of squirrel cage induction generators in wind turbines." Thesis, Cape Peninsula University of Technology, 2017. http://hdl.handle.net/20.500.11838/2530.

Full text

Abstract:

Thesis (MTech (Electrical Engineering))--Cape Peninsula University of Technology, 2017.
Globally governments are faced with challenges in the energy sector which are exacerbated by uncertain financial markets and resource limitations. The over utilization of fossil fuels for electricity generation has had a profound impact on the climatic conditions on earth. Coal power stations release carbon dioxide (CO2) during the combustion process and studies show that concentrations have sharply risen in the atmosphere. Adverse environmental conditions like global warming exist as a result of high greenhouse gas (GHG) emissions in particular CO2. In 2015 Eskom constructed Sere Wind farm with a supply capability of 100 MW. Due to the lack of technical expertise and skills with regard to the new technology within Eskom, Siemens was offered a 5 year maintenance contract. Siemens also provides training on basic operation and maintenance (O&M) of the wind farm to Eskom staff. This excludes specialised training on Siemens Turbine Condition Monitoring (TCM) systems which is a critical part to develop optimum maintenance strategies. This shortage of specialised skills in the application of condition monitoring techniques within Eskom is a major concern. If the most cost effective maintenance strategies during the contract period are implemented, the long term plant health and design life of Sere wind farm will be reduced. There is a need to develop new condition monitoring techniques to complement or address the shortcomings of the existing systems. Developing these skills will increase the understanding of the technology and improve the operating and maintenance of Sere wind farm.

APA, Harvard, Vancouver, ISO, and other styles

22

Rouillard, Justin. "Can the province of Québec (Canada) learn from Sweden in the field of wind power energy?" Thesis, Uppsala universitet, Institutionen för geovetenskaper, 2012. http://urn.kb.se/resolve?urn=urn:nbn:se:uu:diva-184692.

Full text

Abstract:

For several years now it has been indicated by the scientific research that human activity has a definite impact on the temperature of the Earth. There are different ways of reducing anthropogenic climate change, to consume less energy for instance, but also to use renewable sources of energy. Since the wind power market is growing rapidly lately, it seemed interesting to compare how different countries have developed wind power energy and how they intend to do it in the future. Sweden has developed wind power energy for a long time and since Québec, a Canadian province, is similar to the Scandinavian country in many aspects; it was interesting to determine if the province of Québec in Canada can learn from Sweden in the field of wind power energy. When looking to stimulate wind power on their respective territories, it seems that Sweden and Québec have very different approaches to the development of that energy. In Québec, the governmental policy is criticised because it gives too much latitude to private companies when it is almost the opposite in Sweden, where the government is charged to have introduced too many restrictions and environmental policies that hinder the development of wind power. The conclusion is that Québec can learn from Sweden and from Sweden’s mistakes in the wind energy sector, but also from more successful countries like Denmark and Germany. First, Québec could benefit from having a more decentralised development strategy i.e. giving more power to local authorities and local populations. Second, Québec needs stronger economic incentives providing a stable market for developers.

APA, Harvard, Vancouver, ISO, and other styles

23

Todeschini, Grazia. "Wind Energy Conversion Systems based on DFIG Technology used as Active Filters: Steady-State and Transient Analysis." Digital WPI, 2010. https://digitalcommons.wpi.edu/etd-dissertations/97.

Full text

Abstract:

This thesis deals with the performance of a Wind Energy Conversion System operating as a power generator and Active Filter simultaneously. As a power generator, the Wind Energy Conversion System converts wind energy into electric energy; as an Active Filter, it sinks the harmonic currents injected by Non-Linear Loads connected at the same feeder. Three control systems are developed to ensure the described operation; a specific study regarding the compensation of the triplen harmonics is carried out; Doubly-Fed Induction Generator derating is defined; and an engineering economic analysis is performed to determine the profitability of the proposed operation. The Wind Energy Conversion System performance as generator and Active Filter has been studied for steady-state analysis, fast transients and low transients. It is concluded that the proposed control systems allow operating the Wind Energy Conversion System as power generator and harmonic compensator both during steady state and transient operation; the described operation causes power loss increase and voltage distortion that determine the choice of the component and require system derating.

APA, Harvard, Vancouver, ISO, and other styles

24

Blockey, James Craig. "Feasibility in developing smart structures for use in wind turbine blades." Thesis, Montana State University, 2008. http://etd.lib.montana.edu/etd/2008/blockey/BlockeyJ0808.pdf.

Full text

Abstract:

Recently the use of wind as an alternative energy source has developed quickly. The length of the blades is a leading factor in the power output of a wind turbine and as a result, blade length has grown at a similar pace to the growth of the industry. The rapid expansion in use and size of wind turbines is not without its problems, though. As the industry has changed and grown, the overall design of the blades has remained relatively stagnant. This is evident in two primary areas, power control and health monitoring. Power control mechanisms are generally unchanged, utilizing either pitch control or active stall designs. While effective, these systems are neither efficient nor fast acting and can contribute to higher maintenance requirements. Current wind turbine blades also have no sensors built into them. The nacelle and tower utilize many sensors, but the blades themselves have none, leading to blades which are incapable of any real time health monitoring. The application of smart structures will enable the in situ monitoring of the blade and allow the blade to adapt to changing wind loadings Smart structures are those which apply an array of sensors to continuously monitor the state of the structure and are capable of using those sensors to appropriately react to achieve a desired state. This paper will examine the application of smart structures to the wind energy industry. It will be shown that a fiber optic, Fiber Bragg Grating sensor is the best type of sensor for wind energy. One of the main contributing factors is the capability of the sensors to multiplex, which means many sensors can be located along a single optical fiber and different types of sensors can be run on the same optical fiber. The blades will \'react\' to changing conditions through the use of an actuated Gurney style flap. The flap will be used to shed the wind loads from the blade in high wind scenarios. These systems working together will provide an effective and efficient method of advancing the design of the wind turbine blade to a level appropriate for the systems expected today and in the future.

APA, Harvard, Vancouver, ISO, and other styles

25

Stander, Johan Nico. "The specification of a small commercial wind energy conversion system for the South African Antarctic Research Base SANAE IV." Thesis, Stellenbosch : Stellenbosch University, 2008. http://hdl.handle.net/10019.1/1583.

Full text

Abstract:

Thesis (MScEng (Mechanical and Mechatronic Engineering))--Stellenbosch University, 2008.
The sustainability and economy of the current South African National Antarctic Expedition IV (SANAE IV) base diesel-electric power system are threatened by the current high fuel prices and the environmental pollution reduction obligations. This thesis presents the potential technical, environmental and economical challenges associated with the integration of small wind energy conversion system (WECS) with the current SANAE IV diesel fuelled power system. Criteria derived from technical, environmental and economic assessments are applied in the evaluation of eight commercially available wind turbines as to determine the most technically and economically feasible candidates. Results of the coastal Dronning Maud Land and the local Vesleskarvet cold climate assessments based on long term meteorological data and field data are presented. Field experiments were performed during the 2007-2008 austral summer. These results are applied in the generation of a wind energy resource map and in the derivation of technical wind turbine evaluation criteria. The SANAE IV energy system and the electrical grid assessments performed are based on long term fuel consumption records and 2008 logged data. Assessment results led to the identification of SANAE IV specific avoidable wind turbine grid integration issues. Furthermore, electro-technical criteria derived from these results are applied in the evaluation of the eight selected wind turbines. Conceptual wind turbine integration options and operation modes are also suggested. Wind turbine micro-siting incorporating Vesleskarvet specific climatological, environmental and technical related issues are performed. Issues focusing on wind turbine visual impact, air traffic interference and the spatial Vesleskarvet wind distribution are analysed. Three potential sites suited for the deployment of a single or, in the near future, a cluster of small wind turbines are specified. Economics of the current SANAE IV power system based on the South African economy (May 2008) are analysed. The life cycle economic impact associated with the integration of a small wind turbine with the current SANAE IV power system is quantified. Results of an economic sensitivity analysis are used to predict the performance of the proposed wind-diesel power systems. All wind turbines initially considered will recover their investment costs within 20 years and will yield desirable saving as a result of diesel fuel savings, once integrated with the SANAE IV diesel fuelled power system. Finally, results of the technical and economical evaluation of the selected commercially available wind turbines indicated that the Proven 6 kWrated, Bergey 10 kWrated and Fortis 10 kWrated wind turbines are the most robust and will yield feasible savings.

APA, Harvard, Vancouver, ISO, and other styles

26

Cunningham, John B. "Field Testing the Effects of Low Reynolds Number on the Power Performance of the Cal Poly Wind Power Research Center Small Wind Turbine." DigitalCommons@CalPoly, 2020. https://digitalcommons.calpoly.edu/theses/2249.

Full text

Abstract:

This thesis report investigates the effects of low Reynolds number on the power performance of a 3.74 m diameter horizontal axis wind turbine. The small wind turbine was field tested at the Cal Poly Wind Power Research Center to acquire its coefficient of performance, Cp, vs. tip speed ratio, λ, characteristics. A description of both the wind turbine and test setup are provided. Data filtration and processing techniques were developed to ensure a valid method to analyze and characterize wind power measurements taken in a highly variable environment. The test results demonstrated a significant drop in the wind turbine’s power performance as Reynolds number decreased. From Re = 2.76E5 to Re = 1.14E5, the rotor’s Cp_max changed from 0.30 to 0.19. The Cp vs. λ results also displayed a clear change in shape with decreasing Reynolds number. The analysis highlights the influence of the rotor’s Cl /Cd characteristics on the Cp vs. λ curve’s Reynolds number dependency. By not accounting for the effects of varying Reynolds number below the critical value for a rotor operating at constant λ, the design of the rotor planform may overestimate the actual performance of the turbine in real-world conditions. This problem is more evident in distributed-scale wind turbines, compared to utility-scale ones, because of the significantly shorter chord lengths, and therefore increased wind speed range where this effect occurs. Lastly, the wind turbine’s future control method and annual energy production are evaluated using the test results.

APA, Harvard, Vancouver, ISO, and other styles

27

Mitchell-Colgan, Elliott James. "Improved Dynamical Analysis Tools for DFIG Wind Farms via Traditional and Koopman Linearizations." Diss., Virginia Tech, 2009. http://hdl.handle.net/10919/94134.

Full text

Abstract:

The electric power system is designed to economically and reliably transmit electricity to homes, industry, and businesses. The economic impact of the electric grid was demonstrated by the 2003 blackout's visible impact in the graph of the yearly gross domestic product of the Unites States. However, because the number of customers is so large and economies of scale are leveraged to keep electricity prices low, utilities are strongly interconnected. Performing comprehensive engineering analyses to ensure reliable operation is still impossible. Instead, heuristics and safety factors are incorporated into planning processes to continually meet demand in a way that complies with Federal regulations. As evidenced by the infrequency of blackouts in the United States, the sophisticated planning processes have up to date been relatively successful. However, the power system is constantly changing. Electrical generators based on renewable energies are a beneficial addition to the grid, but these and other technological changes like high-voltage power electronic converters also come with their own challenges. These systems as currently employed tend to have a different impact on the reliability of operation than traditional fossil fuel based generators. As the system changes, so do the engineering analyses required to ensure reliable operation. In particular, the wind energy conversion systems (WECS) negatively impact the response of the grid to disturbances in certain ways due to inherent challenges harnessing the wind as an energy sources. These negative impacts (and the advent of powerful personal computing) require an increase in the sophistication of power system models. Thus, there are competing challenges: the scale of the power system necessitates computationally efficient modeling, but the complexity of analysis required to maintain reliable operation is also increasing. The primary aim of this study is to develop models and methods for more detailed yet computationally manageable simulation. To this aim, higher order linearizations and the properties of linear systems (graph theory and linear algebra) are exploited. More specifically, this document contains three studies. In the short term planning and situational awareness context, a method is proposed to quickly check credible outages of important grid equipment. This methodology enables the inspection of a wider breadth of system conditions to ameliorate the negative impacts of the unpredictability of the wind. A linear model in the traditional sense is also developed to model any arbitrary number of wind turbines in a wind farm. This enables industry players to study the impacts wind turbine interaction on the dynamic stability of the grid in response to small disturbances. Finally, a wind farm is modeled as a large matrix to model even nonlinear behavior of wind farms. This helps industry players analyze the impact of large disturbances on the grid.
Doctor of Philosophy
The electric power system is designed to economically and reliably transmit electricity to homes, industry, and businesses. The economic impact of the electric grid was demonstrated by the 2003 blackout’s visible impact in the graph of the yearly gross domestic product of the United States. However, because the number of customers is so large and economies of scale are leveraged to keep electricity prices low, utilities are strongly interconnected. Performing comprehensive engineering analyses to ensure reliable operation is still impossible. Instead, heuristics and safety factors are incorporated into planning processes to continually meet demand in a way that complies with Federal regulations. As evidenced by the infrequency of blackouts in the United States, the sophisticated planning processes have up to date been relatively successful. However, the power system is constantly changing. Electrical generators based on renewable energies are a beneficial addition to the grid, but these and other technological changes like high-voltage power electronic converters also come with their own challenges. These systems as currently employed tend to have a different impact on the reliability of operation than traditional fossil fuel based generators. As the system changes, so do the engineering analyses required to ensure reliable operation. In particular, the wind energy conversion systems (WECS) negatively impact the response of the grid to disturbances in certain ways due to inherent challenges harnessing the wind as an energy sources. These negative impacts (and the advent of powerful personal computing) require an increase in the sophistication of power system models. Thus, there are competing challenges: the scale of the power system necessitates computationally efficient modeling, but the complexity of analysis required to maintain reliable operation is also increasing. The primary aim of this study is to develop models and methods for more detailed yet computationally manageable simulation. To this aim, higher order linearizations and the properties of linear systems (graph theory and linear algebra) are exploited. More specifically, this document contains three studies. In the short term planning and situational awareness context, a method is proposed to quickly check credible outages of important grid equipment. This methodology enables the inspection of a wider breadth of system conditions to ameliorate the negative impacts of the unpredictability of the wind. A linear model in the traditional sense is also developed to model any arbitrary number of wind turbines in a wind farm. This enables industry players to study the impacts wind turbine interaction on the dynamic stability of the grid in response to small disturbances. Finally, a wind farm is modeled as a large matrix to model even nonlinear behavior of wind farms. This helps industry players analyze the impact of large disturbances on the grid.

APA, Harvard, Vancouver, ISO, and other styles

28

Mitchell-Colgan, Elliott. "Improved Dynamical Analysis Tools for DFIG Wind Farms via Traditional and Koopman Linearizations." Diss., Virginia Tech, 2019. http://hdl.handle.net/10919/94134.

Full text

Abstract:

The electric power system is designed to economically and reliably transmit electricity to homes, industry, and businesses. The economic impact of the electric grid was demonstrated by the 2003 blackout's visible impact in the graph of the yearly gross domestic product of the Unites States. However, because the number of customers is so large and economies of scale are leveraged to keep electricity prices low, utilities are strongly interconnected. Performing comprehensive engineering analyses to ensure reliable operation is still impossible. Instead, heuristics and safety factors are incorporated into planning processes to continually meet demand in a way that complies with Federal regulations. As evidenced by the infrequency of blackouts in the United States, the sophisticated planning processes have up to date been relatively successful. However, the power system is constantly changing. Electrical generators based on renewable energies are a beneficial addition to the grid, but these and other technological changes like high-voltage power electronic converters also come with their own challenges. These systems as currently employed tend to have a different impact on the reliability of operation than traditional fossil fuel based generators. As the system changes, so do the engineering analyses required to ensure reliable operation. In particular, the wind energy conversion systems (WECS) negatively impact the response of the grid to disturbances in certain ways due to inherent challenges harnessing the wind as an energy sources. These negative impacts (and the advent of powerful personal computing) require an increase in the sophistication of power system models. Thus, there are competing challenges: the scale of the power system necessitates computationally efficient modeling, but the complexity of analysis required to maintain reliable operation is also increasing. The primary aim of this study is to develop models and methods for more detailed yet computationally manageable simulation. To this aim, higher order linearizations and the properties of linear systems (graph theory and linear algebra) are exploited. More specifically, this document contains three studies. In the short term planning and situational awareness context, a method is proposed to quickly check credible outages of important grid equipment. This methodology enables the inspection of a wider breadth of system conditions to ameliorate the negative impacts of the unpredictability of the wind. A linear model in the traditional sense is also developed to model any arbitrary number of wind turbines in a wind farm. This enables industry players to study the impacts wind turbine interaction on the dynamic stability of the grid in response to small disturbances. Finally, a wind farm is modeled as a large matrix to model even nonlinear behavior of wind farms. This helps industry players analyze the impact of large disturbances on the grid.
Doctor of Philosophy
The electric power system is designed to economically and reliably transmit electricity to homes, industry, and businesses. The economic impact of the electric grid was demonstrated by the 2003 blackout’s visible impact in the graph of the yearly gross domestic product of the United States. However, because the number of customers is so large and economies of scale are leveraged to keep electricity prices low, utilities are strongly interconnected. Performing comprehensive engineering analyses to ensure reliable operation is still impossible. Instead, heuristics and safety factors are incorporated into planning processes to continually meet demand in a way that complies with Federal regulations. As evidenced by the infrequency of blackouts in the United States, the sophisticated planning processes have up to date been relatively successful. However, the power system is constantly changing. Electrical generators based on renewable energies are a beneficial addition to the grid, but these and other technological changes like high-voltage power electronic converters also come with their own challenges. These systems as currently employed tend to have a different impact on the reliability of operation than traditional fossil fuel based generators. As the system changes, so do the engineering analyses required to ensure reliable operation. In particular, the wind energy conversion systems (WECS) negatively impact the response of the grid to disturbances in certain ways due to inherent challenges harnessing the wind as an energy sources. These negative impacts (and the advent of powerful personal computing) require an increase in the sophistication of power system models. Thus, there are competing challenges: the scale of the power system necessitates computationally efficient modeling, but the complexity of analysis required to maintain reliable operation is also increasing. The primary aim of this study is to develop models and methods for more detailed yet computationally manageable simulation. To this aim, higher order linearizations and the properties of linear systems (graph theory and linear algebra) are exploited. More specifically, this document contains three studies. In the short term planning and situational awareness context, a method is proposed to quickly check credible outages of important grid equipment. This methodology enables the inspection of a wider breadth of system conditions to ameliorate the negative impacts of the unpredictability of the wind. A linear model in the traditional sense is also developed to model any arbitrary number of wind turbines in a wind farm. This enables industry players to study the impacts wind turbine interaction on the dynamic stability of the grid in response to small disturbances. Finally, a wind farm is modeled as a large matrix to model even nonlinear behavior of wind farms. This helps industry players analyze the impact of large disturbances on the grid.

APA, Harvard, Vancouver, ISO, and other styles

29

Fischer, Felix Friedrich. "The regulation of Section 17 (2a) of the German Energy Economy Act against the background of current developments of the German and European offshore wind industry." Thesis, Stellenbosch : Stellenbosch University, 2008. http://hdl.handle.net/10019.1/5750.

Full text

Abstract:

Thesis (MBA (Business Management))--Stellenbosch University, 2008.
ENGLISH ABSTRACT: With the introduction of Section 17 of the EnWG (German Energy Economy Act), the legislator created a new situation for the complex relationships in the German offshore wind industry. The transmission system operators are now obliged not only to provide the connection for offshore wind farms, but also to reimburse the developers of such plants for the costs they incurred in the course of planning the cable connection between the wind farm and the onshore grid. Forecasts had predicted that by 2007 numerous offshore wind farms would be operational. But no development company in the entire sector had moved beyond the planning phase. However, the rapid development of the offshore wind industry is important in order to achieve the German goal to generate 20% of all energy from renewable energy sources by 2020 and thus contribute to the prevention of grave climate changes. It is also important for the domestic labour market and the initiation of further exports of energy technologies. Early domestic growth will eventually payoff as offshore wind energy is implemented by more countries, which will then rely on the experience of German companies. Under these circumstances, Section 17 (2a) S.3 of the EnWG induces a positive impulse for offshore development. Under the financial constraints that dampened the expectations of developers of offshore wind farms, the suggested reimbursement will offer welcome relief. However a broad interpretation of Section 17 (2a) S.3 of the EnWG must be applied in order to reach the goal of actually enhancing offshore development, as is the legislator's intent. Such a broad interpretation of the reimbursement claim will lead to rapid implementation of the new law, as this will be in the interest of the developers and transmission system operators. The developers will have a large interest in beginning with the actual construction of the wind farm, and the transmission system operators will need to proceed with the planning of the cable connection. Even though improvements remain necessary the introduction of Section 17 (2a) S.3 EnWG can be considered a success.
AFRIKAANSE OPSOMMING: Met die inwerkingstelling van afdeling 17 van die EnGW (Duitse Energie Ekonomie Wet), het die regering 'n nuwe situasie geskep vir die komplekse verhouding in die Duitse see-gebonde wind-energie industrie. Die transmissie stelsel operateurs word nou verplig om nie net die verbinding met die wind-plaas te verskaf nie, maar moet ook die ontwikkelaar van die aanleg vergoed vir enige kostes wat hulle aangegaan het met die beplanning van die verbinding tussen die windplaas en die elektrisiteits-netwerk. Vooruitskattings het voorspel dat verskeie see-gebonde windplase operasioneel sou wees teen 2007. Geen ontwikkelingsmaatskappy het egter al tot dusver verder as die beplanningstadium gevorder nie. Desnieteenstaande, die spoedige ontwikkeling van die see-gebonde wind industrie is onontbeerlik in die Duitse mikpunt om 20% van energiebehoeftes op te wek vanuit hernubare bronne teen 2020 en om dus klimaatsverandering teen te werk. Dit is ook belangrik vir werkskepping in Duitsland en vir die uitvoer van energie tegnologie. Spoedige groei in die industrie sal uiteindelik dividende lewer soos seegebonde wind-energie deur ander lande ontwikkel word en gevolglik op Duitse ervaring moet staatmaak. Onder hierdie omstandighede het afdeling 17 (2a) 5.3 van die EnGW 'n positiewe effek op seegebonde ontwikkeling. As gevolg van die dempende effek wat finansiele beperkinge het op die verwagtinge van ontwikkelaars sal die terugbetalings welkome verligting bied. Dit is egter nodig om 'n bree interpretasie van afdeling 17 (2a) 5.3 van die EnGW te gebruik om die mikpunt van werklike bevordering van seegebonde ontwikkeling te bewerkstellig soos die wetgewer beoog. So 'n bree interpretasie sal lei tot spoedige implimentasie van die nuwe wet omdat dit in die belang van ontwikkelaars en transmissie-netwerk eienaars sal wees. Die ontwikkelaars sal baat daarby om spoedig met ontwikkeling te begin, terwyl die netwerk operateurs vordering sal moet maak met die beplanning van die kabel-verbinding. Ten spyte daarvan dat verdere verbeteringe nodig is kan die inwerkingstelling van afdeling 17 (2a) 5.3 van die EnGW as 'n sukses gereken word.

APA, Harvard, Vancouver, ISO, and other styles

30

Jarvis, Christina M. "An evaluation of the wildlife impacts of offshore wind development relative to fossil fuel power production." Access to citation, abstract and download form provided by ProQuest Information and Learning Company; downloadable PDF file 0.67 Mb., 123 p, 2006. http://gateway.proquest.com/openurl?url_ver=Z39.88-2004&res_dat=xri:pqdiss&rft_val_fmt=info:ofi/fmt:kev:mtx:dissertation&rft_dat=xri:pqdiss:1430770.

Full text

APA, Harvard, Vancouver, ISO, and other styles

31

Liang, Jiaqi. "Wind energy and power system interconnection, control, and operation for high penetration of wind power." Diss., Georgia Institute of Technology, 2012. http://hdl.handle.net/1853/47570.

Full text

Abstract:

High penetration of wind energy requires innovations in different areas of power engineering. Methods for improving wind energy and power system interconnection, control, and operation are proposed in this dissertation. A feed-forward transient compensation control scheme is proposed to enhance the low-voltage ride-through capability of wind turbines equipped with doubly fed induction generators. Stator-voltage transient compensation terms are introduced to suppress rotor-current overshoots and torque ripples during grid faults. A dynamic stochastic optimal power flow control scheme is proposed to optimally reroute real-time active and reactive power flow in the presence of high variability and uncertainty. The performance of the proposed power flow control scheme is demonstrated in test power systems with large wind plants. A combined energy-and-reserve wind market scheme is proposed to reduce wind production uncertainty. Variable wind reserve products are created to absorb part of the wind production variation. These fast wind reserve products can then be used to regulate system frequency and improve system security.

APA, Harvard, Vancouver, ISO, and other styles

32

Esmaili, Gholamreza. "Application of advanced power electronics in renewable energy sources and hybrid generating systems." Columbus, Ohio : Ohio State University, 2006. http://rave.ohiolink.edu/etdc/view?acc%5Fnum=osu1141850833.

Full text

APA, Harvard, Vancouver, ISO, and other styles

33

Kerley, Ross. "Small-scale hybrid alternative energy maximizer for wind turbines and photovoltaic panels." Honors in the Major Thesis, University of Central Florida, 2011. http://digital.library.ucf.edu/cdm/ref/collection/ETH/id/457.

Full text

Abstract:

This thesis describes the creation of a small-scale Hybrid Power System (HPS) that maximizes energy from a wind turbine and photovoltaic array. Small-scale HPS are becoming an increasingly viable energy solution as fossil fuel prices rise and more electricity is needed in remote areas. Modern HPS typically employ wind speed sensors and three power stages to extract maximum power. Modern systems also use passive rectifiers to convert AC from the wind turbine to DC that is usable by power electronics. This passive system inefficiently wastes power and introduces damaging harmonic noise to the wind turbine. The HPS described in this thesis does not require external wind speed sensors, and has independent wind and solar Maximum Power Point Tracking (MPPT). It converts AC from the wind turbine to DC with a Vienna rectifier that can be controlled to improve efficiency, allow MPPT, and allow Power Factor Correction (PFC). PFC all but eliminates the harmonic noise that can damage the wind turbine. A prototype HPS was built and evaluated that combines the two renewable sources in such a way that only two power stages are necessary, the Vienna rectifier and a step-down converter. This thesis describes the prototype and reports the results obtained.
B.S.
Bachelors
Engineering and Computer Science

APA, Harvard, Vancouver, ISO, and other styles

34

Jones, Gavin Wesley. "Distribution system operation and planning in the presence of distributed generation technology." Diss., Rolla, Mo. : University of Missouri-Rolla, 2007. http://scholarsmine.umr.edu/thesis/pdf/Jones_09007dcc803b193d.pdf.

Full text

Abstract:

Thesis (M.S.)--University of Missouri--Rolla, 2007.
Vita. The entire thesis text is included in file. Title from title screen of thesis/dissertation PDF file (viewed November 16, 2007) Includes bibliographical references (p. 71-74).

APA, Harvard, Vancouver, ISO, and other styles

35

DeLucia, Dominic. "A Parametric Study on Power Variation for Model Wind Turbine Arrays." PDXScholar, 2013. http://pdxscholar.library.pdx.edu/open_access_etds/1120.

Full text

Abstract:

This thesis presents the results of wind tunnel experiments performed for various model wind turbine arrays. The aim is to understand how siting affects power output. To optimize wind farm efficiency the experiments vary the parameters of the model wind turbines and the layout of the wind turbine array. The parameters include the alignment, height, spacing, and the rotational direction of the model wind turbines. These experiments employ mechanical torque sensors to simultaneously measure the torque and rotor angular velocity, which yields a direct measurement of the fluid mechanical power extracted by the turbine at multiple locations. For a 4 × 3 array, the power is calculated at the center turbine in each of the rows. Variations in wind farm efficiency ranging from 55% to 90% are observed between the 13 different layouts tested. Modifications to the layout of the wind turbine array clearly affects the power output of the wind turbines downstream. The results of such experiments highlight the importance of studying the relationship between wind farm layout and power output.

APA, Harvard, Vancouver, ISO, and other styles

36

Gogas, Kyriakos. "Design of a robust speed and position sensorless decoupled P-Q controlled doubly-fed induction generator for variable-speed wind energy applications." Thesis, McGill University, 2007. http://digitool.Library.McGill.CA:80/R/?func=dbin-jump-full&object_id=99762.

Full text

Abstract:

Wind energy is a relatively young but rapidly expanding industry. In order for wind generation to be cost effective, it must produce energy at a minimum cost per dollar of investment. Performance characteristics such as power output versus wind speed must be optimized in order to compete with other energy sources. Also, if the utility uses wind power for a part of its generation, the output power of these turbines must have the same high quality and reliability when it enters the utility grid. The ability to vary operating speed is important in wind generation because it allows for an optimization of the transfer of power from the wind to the turbine shaft. Doubly-fed induction generators (DFIG) are an interesting solution for variable-speed systems with limited variable speed range, and are typically used in wind energy conversion systems.
The objectives of this thesis are to implement a decoupled P-Q control of a DFIG that does not rely on mechanical sensors and to design a speed and position sensorless algorithm that is robust to variations of the values of the machine parameters. The sensorless DFIG control algorithm presented in this thesis is based on a modified phasedlock loop with an improved positioning algorithm. With the measured stator voltages, stator and rotor currents, the speed and position of the DFIG are estimated. The speed is estimated independent of machine parameters, which results in a significant improvement in speed control robustness to parameter variations. In addition, the algorithm avoids using differentiation, which significantly improves its immunity to noise and does not require the measurement of the rotor voltages. Also, it is shown that the positioning algorithm has an improved operation in generator mode. Although the accuracy of the positioning algorithm is depended on machine parameters; it is shown with the designed controller that the P-Q decoupled control is robust to changes of machine parameters. Theoretical and simulation results are validated on an experimental setup.

APA, Harvard, Vancouver, ISO, and other styles

37

Caballero, Diaz Luis. "Contributions to the design and operation of a multilevel-active-clamped Dc-Ac grid- connected power converter for wind energy conversion systems." Doctoral thesis, Universitat Politècnica de Catalunya, 2017. http://hdl.handle.net/10803/454979.

Full text

Abstract:

The demand of wind energy has considerably increased during the last decades. In order to fulfil this great energy demand, wind energy conversion systems (WECS) are designed to manage higher power ratings. Currently, the most attractive power converter topology in commercial WECS is the conventional two-level back-to-back voltage-source converter (2L-B2B). However, the 2L-B2B topology could have difficulties to achieve an acceptable performance with the available switching devices for the largest WECS, even though having the cost advantage. Instead, multilevel converters increase the power without increasing neither current nor blocking voltage of the power semiconductors, enabling a cost-effective design for the largest WECS using the available switching devices. Within the multilevel converters, the 3L-NPC topology offers high penetration in the market of large WECS. However, one of its major drawbacks is that the power loss is unevenly distributed among the switching devices. Therefore, the 3L-NPC output power capability is limited by the thermal performance of the most stressed switching device, which depends on the operating point. The 3L-ANPC topology was proposed in order to improve the power loss distribution among the power semiconductors. The 3L-ANPC provides a controllable path for the neutral current. Hence, the 3L-ANPC is able to offer certain freedom to distribute the power loss among the power semiconductors. As a consequence, and compared to the 3L-NPC, the thermal performance is more uniform and the output power capability increases. However, there is still room for improvement. In light of the previous discussion, the proposed thesis defines enhanced design guidelines for the dc-ac grid-connected 3L-ANPC power converter, focused on improving its reliability and electrical performance, and following the trend of the current state of the art to define a feasible solution for the next generation of WECS. The thesis contributions are based on defining an enhanced power device configuration and a novel commutation sequence, avoiding concentrating both significant conduction and switching losses on a single power semiconductor device. This allows then selecting the most appropriate device for each converter position, which leads to a better converter efficiency and to a more uniform power loss distribution and thermal performance. This also leads to a higher converter power rating, and it is expected to improve the converter reliability.
La demanda de energía eólica ha incrementado considerablemente durante las últimas décadas. Con el objetivo de satisfacer esta gran demanda, los sistemas de conversión de energía eólica (WECS) son diseñados para operar con mayores niveles de potencia. Actualmente, la topología de convertidor de potencia más atractiva en los WECS comerciales es el convertidor de dos niveles operando en fuente de tensión y configuración back to back (2L-B2B). Sin embargo, esta topología podría tener dificultades para ofrecer un comportamiento aceptable en los WECS de mayor potencia con los dispositivos actuales, incluso aunque su coste sea reducido. En cambio, los convertidores multinivel pueden incrementar la potencia sin necesidad de incrementar la corriente ni el voltaje de bloqueo de los dispositivos, permitiendo conseguir un diseño adecuado para los WECS de mayor potencia usando los dispositivos actuales. Dentro de los convertidores multinivel, la topología 3L-NPC tiene una gran aceptación en el mercado eólico, siendo una solución común en los WECS de mayor potencia. Sin embargo, su gran inconveniente es que la potencia pérdida es distribuida de una manera desequilibrada entre los dispositivos. De este modo, la potencia de salida se ve limitada por el comportamiento térmico del dispositivo más estresado a nivel térmico, el cual depende del punto de operación. De esta manera, la topología 3L-ANPC fue propuesta con el objetivo de mejorar la distribución de las pérdidas del convertidor entre los dispositivos. El convertidor 3L-ANPC proporciona un camino totalmente controlable para la conexión del punto neutro. Por lo tanto, el convertidor 3LANPC es capaz de ofrecer cierto grado de libertad para distribuir la potencia pérdida entre los dispositivos. Como consecuencia, y comparado con el convertidor 3L-NPC, el comportamiento térmico es mucho más equilibrado y la potencia de salida puede ser incrementada. Sin embargo, todavía hay margen de mejora para alcanzar mejores prestaciones en el comportamiento del convertidor 3L-ANPC. A raíz de la argumentación anterior, la tesis propuesta define nuevas guías de diseño para el convertidor 3L-ANPC cc-ca conectado a la red. Las guías de diseño están focalizadas en mejorar la fiabilidad y el comportamiento eléctrico del convertidor, respetando la tendencia del estado del arte actual para definir una solución factible para la próxima generación de WECS. Las contribuciones de la tesis están basadas en definir una configuración de dispositivos mejorada y una secuencia de conmutación novedosa, evitando concentrar grandes pérdidas de conducción y de conmutación en un mismo dispositivo. Las contribuciones permiten seleccionar el dispositivo más adecuado para cada posición del convertidor, consiguiendo una mejor eficiencia y una distribución de pérdidas y comportamiento térmico más equilibrado. Además, también permiten operar con potencias más elevadas, y mejorar la fiabilidad del convertidor.

APA, Harvard, Vancouver, ISO, and other styles

38

Yin, Hang [Verfasser], Sibylle [Akademischer Betreuer] Dieckerhoff, Sibylle [Gutachter] Dieckerhoff, Uwe [Gutachter] Schäfer, and Lijun [Gutachter] Cai. "Grid current control methods for MV wind energy conversion systems / Hang Yin ; Gutachter: Sibylle Dieckerhoff, Uwe Schäfer, Lijun Cai ; Betreuer: Sibylle Dieckerhoff." Berlin : Technische Universität Berlin, 2019. http://d-nb.info/1193570565/34.

Full text

APA, Harvard, Vancouver, ISO, and other styles

39

Jayam, Prabhakar Aditya. "Application of STATCOM for improved dynamic performance of wind farms in a power grid." Diss., Rolla, Mo. : Missouri University of Science and Technology, 2008. http://scholarsmine.mst.edu/thesis/pdf/Jayam_Prabhakar_09007dcc804f7428.pdf.

Full text

Abstract:

Thesis (M.S.)--Missouri University of Science and Technology, 2008.
Vita. The entire thesis text is included in file. Title from title screen of thesis/dissertation PDF file (viewed May 12, 2008) Includes bibliographical references (p. 64-66).

APA, Harvard, Vancouver, ISO, and other styles

40

Yunus, A. M. Shiddiq. "Application of SMES Unit to improve the performance of doubly fed induction generator based WECS." Thesis, Curtin University, 2012. http://hdl.handle.net/20.500.11937/1450.

Full text

Abstract:

Due to the rising demand of energy over several decades, conventional energy resources have been continuously and drastically explored all around the world. As a result, global warming is inevitable due to the massive exhaust of CO2 into the atmosphere from the conventional energy sources. This global issue has become a high concern of industrial countries who are trying to reduce their emission production by increasing the utilization of renewable energies such as wind energy. Wind energy has become very attractive since the revolution of power electronics technology, which can be equipped with wind turbines. Wind energy can be optimally captured with wind turbine converters. However, these converters are very sensitive if connected with the grid as grid disturbances may have a catastrophic impact on the overall performance of the wind turbines.In this thesis, superconducting magnetic energy storage (SMES) is applied on wind energy conversion systems (WECSs) that are equipped with doubly fed induction generators (DFIGs) during the presence of voltage sags and swells in the grid side. Without SMES, certain levels of voltage sags and swells in the grid side may cause a critical operating condition that may require disconnection of WECS to the grid. This condition is mainly determined by the voltage profile at the point of common coupling (PCC), which is set up differently by concerned countries all over the world. This requirement is determined by the transmission system operator (TSO) in conjunction with the concerned government. The determined requirement is known as grid codes or fault ride through (FRT) capability.The selection of a SMES unit in this thesis is based on its advantages over other energy storage technologies. Compared to other energy storage options, the SMES unit is ranked first in terms of highest efficiency, which is 90-99%. The high efficiency of the SMES unit is achieved by its low power loss because electric currents in the coil encounter almost no resistance and there are no moving parts, which means no friction losses. Meanwhile, DFIG is selected because it is the most popular installed WECS over the world. In 2004 about 55% of the total installed WECS worldwide were equipped with DFIG. There are two main strategies that can be applied to meet the grid requirements of a particular TSO. The first strategy is development of new control techniques to fulfil the criterion of the TSOs. This strategy, however, is applicable only to the new WECS that have not been connected to the power grid. If new control techniques are applied to the existing gridconnected WECSs, they will not be cost effective because the obsolete design must be dismantled and re-installed to comply with current grid code requirements. The second strategy is the utilization of flexible AC transmission system (FACTS) devices or storage energy devices to meet the grid code requirements. This strategy seems more appropriate for implementation in the existing WECS-grid connection in order to comply with the current grid code requirements. By appropriate design, the devices might be more cost effective compared to the first strategy, particularly for the large wind farms that are already connected to the grid.A new control algorithm of a SMES unit, which is simple but still involves all the important parameters, is employed in this study. Using the hysteresis current control approach in conjunction with a fuzzy logic controller, the SMES unit successfully and effectively improves the performance of the DFIG during voltage sag and swell events in the grid side; thus, this will prevent the WECS equipped with DFIG from being disconnected from the grid according to the selected fault ride through used in this study. The dynamic study of DFIG with SMES during short load variation is carried out as an additional advantage of SMES application on a DFIG system. In this study, the proposed SMES unit is controlled to compensate the reduced transfer power of DFIG during the short load variation event. Moreover, the SMES unit is also engaged in absorbing/storing some amount of excessive power that might be transferred to the grid when the local loads are suddenly decreased. Finally, the studies of intermittent misfires and fire-through that take place within the converters of DFIG are carried out in order to investigate the impact of these converter faults on the performance of DFIG. In this part, the proposed SMES unit is controlled to effectively improve the DFIG’s performance in order to prevent it from being disconnected or shut down from the power grid during the occurrence of these intermittent switching faults.

APA, Harvard, Vancouver, ISO, and other styles

41

Jaramillo, López Fernando. "Control and Model Identification on Renewable Energy Systems." Thesis, Paris 11, 2014. http://www.theses.fr/2014PA112240.

Full text

Abstract:

La situation compromettante de l'environnement due à la pollution, et les coûts élevés des combustibles fossiles ont engagé des nouvelles politiques et réglementations et ont fortement incité l’augmentation de l’utilisation de nouvelles sources d'énergie renouvelables. De nombreux pays dans le monde ont augmenté de façon importante le développement de ces sources d'énergie. Deux des systèmes d'énergies renouvelables les plus couramment utilisés sont les systèmes éoliens (SE) et les systèmes photovoltaïques (SP). SE convertissent l'énergie du vent en énergie électrique au moyen d'un processus électromécanique et SP convertissent directement l'énergie solaire en énergie électrique au moyen d'un processus semi-conducteur. Ces systèmes présentent de nombreux défis qui doivent être résolus afin de gagner du terrain sur les systèmes d'énergies traditionnelles. L'un de ces défis est d'augmenter l'efficacité du système avec la commande des éléments de puissance. Afin d'atteindre cet objectif, il est nécessaire de mieux comprendre le comportement dynamique de ces systèmes et de développer des nouveaux modèles mathématiques et des nouvelles techniques de commande. Ces techniques nécessitent souvent des informations du système qui ne sont pas disponibles --- ou sont trop chères si on devait les mesurer. Pour résoudre ce problème, il est nécessaire de créer des algorithmes qui puissent estimer cette information, cependant, ce n'est pas une tâche facile, car les signaux des sources d'énergie dans SE et SP (c.-à-d. la vitesse du vent, rayonnement solaire, température) entrent dans les modèles mathématiques par une relation non linéaire. Ces algorithmes doivent pouvoir estimer ces signaux --- ou les signaux qui dépendent d’eux--- avec une bonne précision. Aussi, il est nécessaire de concevoir des lois de commande qui opèrent les systèmes à leur point maximum de puissance. Dans ce travail, nous proposons des nouveaux algorithmes d'estimation et des lois de commande qui sont liés à l'augmentation de l'efficacité énergétique dans SE et SP. Des travaux antérieurs liés à l'estimation des signaux mentionnés, les considéraient comme constants. Dans cette thèse, les algorithmes d'estimation proposés considèrent l'état variable des ces signaux. Dans toutes ces nouvelles propositions, la stabilité asymptotique est prouvée en utilisant les théories de Lyapunov. Les lois de commande sont calculées en utilisant les modèles non linéaires des systèmes. En outre, certaines des ces solutions sont étendues au cas général, qui peut être utilisé sur une large classe des systèmes non linéaires. Le premier, est un estimateur de paramètres pour les systèmes non linéaires. Il permet d'estimer les paramètres non linéaires variant dans le temps. La deuxième proposition est la conception d’un schéma pour une classe de systèmes non linéaires adaptatifs qui permet de compenser les incertitudes et les perturbations qui satisfont à la "condition de correspondance"
The compromising situation of the environment due to pollution, and the high costs of the fossil fuels have originated new policies and regulations that have stimulating the interest on alternative energy sources. Many countries around the world have increased in an important way the penetration of these energy sources. Two of the most widely used renewable energy systems are the wind turbines systems (WTS) and the photovoltaic systems (PVS). WTS convert wind energy in electric energy by means of an electromechanical process and PVS convert solar energy directly in electric energy by means of a semiconductive process. These systems show many challenges that need to be solved in order to gain ground to the traditional energy systems. One of these challenges is increase the overall system efficiency by controlling the power conditioning elements. In order to achieve this, is necessary to better understand the dynamic behavior of these systems and develop new mathematical models and new control techniques. These techniques often require system information that is not possible ---or is too expensive--- measure. In order to solve this problem, is necessary to create algorithms that are able to estimate this information, however, this is not an easy task, because the signals of the energy sources in WTS and PVS (i.e., wind speed, irradiance, temperature) enter in the mathematical models in a nonlinear relation. These algorithms have to be able to estimate these signals ---or the signals that depend on them--- with good precision. Also, it is necessary to design control laws that operate the systems at their maximum power point. In this work, we propose novel estimation algorithms and control laws that are related with the increase of the energetic efficiency in WTS and PVS. Previous works related with estimation of the mentioned signals considered them as constants. In this thesis, the proposed estimation algorithms consider the time-varying condition of these signals. In all of these novel propositions, uniform asymptotic stability is proved using Lyapunov theories. The control laws are derived using the overall nonlinear models of the systems. In addition, some of these solutions are extended to the general case, which can be used on a large-class of nonlinear systems. The first one, is a novel parameter estimator for nonlinear systems. It allows to estimate time-varying nonlinear parameters. The second general proposition is a framework for a class of adaptive nonlinear systems that allows to compensate for uncertainties and perturbations that satisfy the matching condition

APA, Harvard, Vancouver, ISO, and other styles

42

van, Niekerk Melanie. "Understanding aquatic carbon loss from upland catchments in south west Scotland during land use change from commercial forest to wind farm." Thesis, University of Stirling, 2012. http://hdl.handle.net/1893/13064.

Full text

Abstract:

High concentrations and fluxes of dissolved organic carbon (DOC) in fluvial systems are associated with the dark brown water colour familiar in many upland, peat-dominated areas and may indicate a depletion of the terrestrial carbon store. The removal of this colour can also be problematic and expensive for water companies as well as affecting the ecological functioning of the water body through factors such as reduced light penetration through the water column. Disturbance resulting from activities such as land use change can also enhance the loss of carbon and this may manifest itself in elevated concentrations and fluxes of DOC from aquatic systems. This thesis describes and explains patterns of change in DOC quantity and quality from the Crosswater, Crosswater of Luce and Tig catchments draining Arecleoch Forest, a peatland in south Ayrshire, Scotland, from 2008 to 2010. This time period incorporates the installation of a 60-turbine wind farm built and operated by Scottish Power Renewables (SPR). Water samples were collected from Arecleoch at different spatial scales ranging from catchments to soil pore water and temporal scales ranging from daily to seasonally. Concentrations of DOC were measured and fluxes estimated at the catchment scale. DOC concentrations from all three catchments exhibited the well-established seasonal pattern with maxima in late August/early September and minima seen in February/March. The Tig catchment experienced the greatest burden of disturbance from the wind farm development and returned the highest DOC concentrations and fluxes. The Crosswater catchment, used as a control site due to its isolation from wind farm activities, had higher DOC concentrations than the Crosswater of Luce throughout the monitoring period possibly due to a greater proportion of forest cover. ii DOC flux ranged from 35.0 g C m-2 yr-1 from the Crosswater of Luce catchment in 2008 to 55.0 g C m-2 yr-1 from the Crosswater in 2009. The Tig catchment was not monitored for the whole period but returned the highest DOC fluxes of the three catchments between January and June 2010 (15.7 g C m-2). These values are considered high for UK peatlands. It is possible to make a tentative estimate of an extra 12 g C m-2 being exported from the Crosswater of Luce in 2009 that may have been a result of wind farm and/or forestry activities in the catchment. At the sub-catchment scale, “hot spots” of high DOC concentrations (up to 113.4 mg L-1) were found during the final survey of headwater streams inside the development area of the wind farm site during construction in August 2010. Further surveys are recommended to assess whether DOC concentrations have decreased since completion of the wind farm. Daily water samples were collected upstream and downstream of turbine 33 during the excavation of the turbine base. DOC concentrations were higher downstream before work began on the turbine base and although the gap between upstream and downstream DOC concentrations increased over the monitoring period, statistical comparisons of these differences before and after the start of excavation work were not significant at the 95 % confidence level. Challenges arose from the practicability of conducting robust research on a construction site and novel approaches to monitoring DOC were developed. Activity scores were used to quantify the effect of peatland disturbance on DOC concentrations at the catchment scale. The results suggest that this approach may have merit but requires comprehensive site records from the developer. The non-linear nature of the individual wind farm development and forestry activities made it impractical to disentangle the impact of each, particularly for forest harvesting. iii Activity scores could, together with other information gathered from site records, be useful to developers as an indicator of the most likely periods for peat disturbance. Knowledge of the differing disturbance potential of the various activities could also provide useful information to feed into the carbon payback calculator. DOC quality was explored using ultraviolet (UV) absorbance, specific UV absorbance (SUVA) and E4/E6 ratios. The latter metric identified changes in the composition of DOC related to disturbance with water samples from areas draining land subject to disturbance having lower E4/E6 ratios indicating a greater degree of humification of the DOC. This research provides one of only three studies to investigate concentrations and fluxes of DOC in water courses draining land subject to disturbance relating to wind farm construction. It is the only study that incorporates a period of time prior to work beginning and takes in the whole of the development phase. In this respect it provides a valuable addition to our understanding of the way in which peatlands respond to land use change and may provide useful tools to assist developers in minimising the impact of their activities on these valuable carbon stores.

APA, Harvard, Vancouver, ISO, and other styles

43

Wang, Tian Xiang. "Study of the integration method on the control of wind power system." Thesis, University of Macau, 2009. http://umaclib3.umac.mo/record=b2144085.

Full text

APA, Harvard, Vancouver, ISO, and other styles

44

Silva, Carlos Elmano de Alencar e. "Estudo e desenvolvimento experimental de um sistema eÃlico interligado a rede elÃtrica." Universidade Federal do CearÃ, 2012. http://www.teses.ufc.br/tde_busca/arquivo.php?codArquivo=7458.

Full text

Abstract:

CoordenaÃÃo de AperfeiÃoamento de Pessoal de NÃvel Superior
FundaÃÃo Cearense de Apoio ao Desenvolvimento Cientifico e TecnolÃgico
Este trabalho apresenta o estudo e desenvolvimento de um sistema eletrÃnico de aproveitamento de energia eÃlica a partir de um gerador sÃncrono de ÃmÃ permanente conectado a uma turbina de vento. O sistema opera com velocidade variÃvel, permitindo o mÃximo aproveitamento da energia cinÃtica incidente na turbina de vento. Essa energia cinÃtica Ã convertida em energia elÃtrica pelo gerador sÃncrono de ÃmÃ permanente e depois de totalmente condicionada, injetada na rede elÃtrica convencional. Esse condicionamento Ã feito por um sistema eletrÃnico objeto de estudo e desenvolvimento deste trabalho, o qual consiste em um retificador trifÃsico interligado a um inversor monofÃsico em ponte completa com saÃda em corrente. SÃo apresentadas a revisÃo bibliogrÃfica de sistemas de aproveitamento de energia eÃlica para geraÃÃo de energia elÃtrica pertinentes ao escopo do trabalho, a anÃlise do estÃgio retificador (potÃncia e controle), a anÃlise do estÃgio inversor (potÃncia e controle), uma comparaÃÃo teÃrica de rendimento entre o retificador trifÃsico proposto neste trabalho (bridgeless trifÃsico) e o retificador trifÃsico dois nÃveis, e os resultados experimentais de um protÃtipo de validaÃÃo de 5kW do sistema proposto.
This work presents the study and development of an electronic system for wind energy exploitation from a permanent magnet synchronous generator connected to a wind turbine. The system operates with variable speed, allowing maximum use of the kinetic energy incident on the wind turbine. This kinetic energy is converted into electrical energy by the permanent magnet synchronous generator and, after being fully conditioned, injected into the conventional power grid. This conditioning is done by an electronic system object of study and development of this work, which consists of a rectifier connected to a single-phase full-bridge inverter with current output. Are presented the literature review of the relevant wind energy conversion systems to the scope of work, the analysis of the rectifier stage (power and control), the analysis of the inverter stage (power and control), a efficiency theoretical comparison between the proposed rectifier (three-phase bridgeless) and the three-phase fullbridge rectifier, and the experimental results of an 5kW validation prototype of the proposed system.

APA, Harvard, Vancouver, ISO, and other styles

45

Tu, Yi-Long, and 杜逸龍. "Estimation of Energy Output from Wind Energy Conversion Systems." Thesis, 2009. http://ndltd.ncl.edu.tw/handle/79577456737574002393.

Full text

Abstract:

博士
國立臺灣大學
生物環境系統工程學研究所
97
The development of wind energy has rapidly and steadily progressed then other renewable energy for the last decade, which is driven by global warming and weather change. An accurate estimation of wind energy output (capacity factor) of a wind energy conversion system (WECS) of a site can help producer to reduce the risk of loss from investment of wind energy. Traditional approach is using the manufacturer’s nominal performance curve to estimate energy output. The Weibull method and chronological (time-series) method are usually used to collocate nominal performance curve to estimate wind energy output. Due to the lack of academic work that compares the differences of the measured and calculated capacity factors of WECS, the wind speed and wind power output data from 2002 to 2006 of the wind power stations, located in Mailiao and Jhongtun, Taiwan, are used to further explore the advantages and drawbacks of using these two methods for estimating capacity factors of WECS in chapter 3. It is shown that thecapacity factors calculated from the time-series approach have better agreement with the actual capacity factors than the Weibull approach. The traditional approach is simple and direct for estimating energy output, but it would cause significant estimation errors. Taking the Vestas V47-660kW as example, the performance curve is made under the standard condition of 1.225 kg/m3 air density, 15℃ temperature and 10% turbulence intensity. The estimation of energy output would result in significant errors, if the wind environment is different from the condition of the nominal performance curve. In addition, because of the climatic features of Asia monsoon, there are different prominent wind periods during a year in Taiwan. For improving the drawbacks of the traditional approach, artificial neuron network (ANN) was chosen to estimate wind energy output. The accuracy of estimating wind energy output by different dataase lengths and different types of database for ANN was studied in chapter 4. The results show that the type of strong and weak wind periods database have the best agreement with the actual capacity factors of all the database types with the same dataase lengths. The advantages and flaws of using different input variable for ANN, such as current and previous observations of wind speed, power output, pitch angle or yaw angle for the previous season and a period of ten days were investigated in chapter 5. It is shown that the ANN model with current observation of wind speed and previous observation of power output yields the best performance.

APA, Harvard, Vancouver, ISO, and other styles

46

Zheng, Y. Y., and 鄭淵元. "Dynamic Behavior of Variable-Speed Wind Energy Conversion Systems." Thesis, 2011. http://ndltd.ncl.edu.tw/handle/82101593575569879117.

Full text

Abstract:

碩士
國立高雄應用科技大學
電機工程系
99
This thesis presents the dynamic behavior simulation of variable-speed wind energy conversion systems operating under normal and abnormal condition. A isolated grid-connected variable-speed wind energy conversion system was studied. System components included wind turbine model, wind speed model, asynchronous induction generator model, three-phase power transformer model, and static synchronous compensator (STATCOM) model. They were developed using SimPowerSystems and employed to cater for the dynamic behavior of the systems. Various system operation conditions were simulated, and the results showed that the systems operated satisfactorily under those conditions. The dynamic behavior study for variable-speed wind energy conversion systems are essential for system planning, operation, and further expansion.

APA, Harvard, Vancouver, ISO, and other styles

47

Hsu, Shan-Ho, and 徐三和. "Sliding-Mode Control Applied to Energy Optimization of Wind Energy Conversion Systems." Thesis, 2011. http://ndltd.ncl.edu.tw/handle/02206567104095151481.

Full text

Abstract:

碩士
國立交通大學
電機學院電機與控制學程
99
This thesis proposes a novel sliding-mode control for the wind energy conversion systems to reach the energy optimization. Since the output power of wind electrical generators tends to interact with wind speed, it is required to operate at the maximum power point so as to enhance the efficiency of wind electrical generators. By tracing the optimal tip speed ratio, the optimal output power and the optimal rotational speed are obtained. After comparing to such optimal speed, the bias of the generator rotational speed is determined and used as the reference to adjust the controller. To design the sliding-mode control, first choose a stable sliding-mode require for the control purpose. Then, construct the control algorithm to drive the system trajectory into the sliding mode in a finite time. As for the chattering phenomenon, it is eliminated by substituing the sliding surface with a sliding layer. In addition, a first-order high pass filter is employed to approximate the undersirable differential operation in the control rule, not to excite high frequence noise. Finially, the simulation of MATLAB/SIMULINK is adopted to demonstrate the robustness of the sliding-mode control at various speed, and the effects on the control accuracy caused by the use of different coefficients in the estimator and control rules. From the numeric results, the proposed sliding-mode control indeed completes the optimal wind energy conversion successfully.

APA, Harvard, Vancouver, ISO, and other styles

48

Rawn, Barry. "Wind energy conversion systems as power filters : a control methodology." 2004. http://link.library.utoronto.ca/eir/EIRdetail.cfm?Resources__ID=95040&T=F.

Full text

APA, Harvard, Vancouver, ISO, and other styles

49

Li, Zong-Han, and 李宗翰. "T-S Fuzzy Power Control for Wind Energy Conversion Systems." Thesis, 2011. http://ndltd.ncl.edu.tw/handle/h35vf7.

Full text

Abstract:

碩士
中原大學
電機工程研究所
99
This thesis focuses on the maximum power tracking for permanent magnetic synchronous generating (PMSG) based wind power energy conversion system (WECS). To achieve the control objective, a DC/DC buck converter is used as the power regulation circuit. Then, the T-S fuzzy tracking controller is designed to drive the operating system to the maximum power point. In the controller design process, the nonlinear model is initially represented into a T-S fuzzy form such that both controller and observer can be obtained via Lyapunov stability analysis and Matlab LMI toolbox. Both simulations and experiments are established to verify the controller’s performances. Moreover, a PI controller is used in comparisons with the proposed controller. In the experiment environments, a real time DSP card dSPACE DS1103 digital processor is used to realize the proposed controller. Finally, the results show good performances in robustness and maximum power tracking for the proposed approach.

APA, Harvard, Vancouver, ISO, and other styles

50

Tsai, Ming Hon, and 蔡明宏. "Dynamic Behavior of Fixed-Speed Variable-Pitch Wind Energy conversion Systems." Thesis, 2011. http://ndltd.ncl.edu.tw/handle/21187021637562644479.

Full text

Abstract:

碩士
國立高雄應用科技大學
電機工程系
99
This thesis presents the dynamic behavior simulation of fixed-speed variable-pitch wind energy conversion systems in SihMen and SihHu wind farms, operating under normal and abnormal conditions. The components of the system were developed using Simulink together with SimPowerSystems and then employed to cater for the dynamic behavior of the system, including wind turbine model, induction generator model, three-phase power transformer model, capacitor bank model, and static load model. The simulation results show that the system operated acceptably under those conditions and are coincident with practical operations. The dynamic behavior studies of fixed-speed variable-pitch wind energy conversion systems are essential for wind turbine power generation system planning,operation, and further expansion。

APA, Harvard, Vancouver, ISO, and other styles

Dissertations / Theses on the topic 'Wind energy conversion systems – Canada'

Create a spot-on reference in APA, MLA, Chicago, Harvard, and other styles