Books on the topic 'White Phosphor'

Chapter 14 discusses specific weapon technologies and types of munition that merit individual consideration. This may be because of concerns that have been expressed as to their characteristics, because the technologies themselves require, or appear to some to require, particular legal care, or because they are emerging technologies which raise interesting and/or novel legal issues. The purpose of this consideration is to show how weapons law should be applied to each such technology, with the ultimate aim of assisting weapon reviewers in their difficult task. The chapter addresses missiles, bombs, and artillery, blast weapons, directed energy weapons, herbicides, flechettes, depleted uranium, white phosphorus, non-lethal weapons, cyber weapons, autonomous weapons, counter-IED weapons, nanotechnology, and metamaterials.

Soil Chemical Methods – Australasia describes over 200 laboratory and field chemical tests relevant to Australasia and beyond. The information and methodology provided across 20 chapters is comprehensive, systematic, uniquely coded, up-to-date and designed to promote chemical measurement quality. There is guidance on the choice and application of analytical methods from soil sampling through to the reporting of results. In many cases, optional analytical ‘finishes’ are provided, such as flow-injection analysis, electro-chemistry, multiple flame technologies, and alternatives to chemical testing offered by near-range and mid-range infrared diffuse reflectance spectroscopy. The book supersedes and updates the soil chemical testing section of the 1992 Australian Laboratory Handbook of Soil and Water Chemical Methods of Rayment and Higginson, while retaining method codes and other strengths of that Handbook. Chapters cover soil sampling, sample preparation and moisture content; electrical conductivity and redox potential; soil pH; chloride; carbon; nitrogen; phosphorus; sulphur; gypsum; micronutrients; extractable iron, aluminium and silicon; saturation extracts; ion-exchange properties; lime requirements; total miscellaneous elements; miscellaneous extractable elements; alkaline earth carbonates and acid sulfate soils. In addition, there are informative Appendices, including information on the accuracy and precision of selected methods. This book targets practising analysts, laboratory managers, students, academics, researchers, consultants and advisors involved in the analysis, use and management of soils for fertility assessments, land use surveys, environmental studies and for natural resource management.

Microbiologists focus on the basic biochemical make-up of microbes, such as relative amounts of protein, RNA, and DNA in cells, while ecologists and biogeochemists use elemental ratios, most notably, the ratio of carbon to nitrogen (C:N), to explore biogeochemical processes and to connect up the carbon cycle with the cycle of other elements. Microbial ecologists make use of both types of data and approaches. This chapter combines both and reviews all things, from elements to macromolecular structures, that make up bacteria and other microbes. The most commonly used elemental ratio was discovered by Alfred Redfield who concluded that microbes have a huge impact on the chemistry of the oceans because of the similarity in nitrogen-to-phosphorus ratios for organisms and nitrate-to-phosphate ratios in the deep oceans. Although statistically different, the C:N ratios in soil microbes are remarkably similar to the ratios of aquatic microbes. The chapter moves on to discussing the macromolecular composition of bacteria and other microbes. This composition gives insights into the growth state of microbes in nature. Geochemists use specific compounds, “biomarkers”, to trace sources of organic material in ecosystems. The last section of the chapter is a review of extracellular polymers, pili, and flagella, which serve a variety of functions, from propelling microbes around to keeping them stuck in one place.

This chapter is focused on the most important process in the biosphere, primary production, the turning of carbon dioxide into organic material by higher plants, algae, and cyanobacteria. Photosynthetic microbes account for roughly 50% of global primary production while the other half is by large, terrestrial plants. After reviewing the basic physiology of photosynthesis, the chapter discusses approaches to measuring gross and net primary production and how these processes affect fluxes of oxygen and carbon dioxide into and out of aquatic ecosystems. It then points out that terrestrial plants have high biomass but relatively low growth, while the opposite is the case for aquatic algae and cyanobacteria. Primary production varies greatly with the seasons in temperate ecosystems, punctuated by the spring bloom when the biomass of one algal type, diatoms, reaches a maximum. Other abundant algal types include coccolithophorids in the oceans and filamentous cyanobacteria in freshwaters. After the bloom, small algae take over and out-compete larger forms for limiting nutrients because of superior uptake kinetics. Abundant types of small algae include two coccoid cyanobacteria, Synechococcus and Prochlorococcus, the latter said to be the most abundant photoautotroph on the planet because of its large numbers in oligotrophic oceans. Other algae, often dinoflagellates, are toxic. Many algae can also graze on other microbes, probably to obtain limiting nitrogen or phosphorus. Still other microbes are mainly heterotrophic but are capable of harvesting light energy. Primary production in oxic environments is carried out by oxygenic photosynthetic organisms, whereas in anoxic environments with sufficient light, it is anaerobic anoxygenic photosynthesis in which oxygen is not produced. Although its contribution to global primary production is small, anoxygenic photosynthesis helps us understand the biophysics and biochemistry of photosynthesis and its evolution on early Earth. These microbes as well as aerobic phototrophic and heterotrophic microbes make up microbial mats. These mats can provide insights into early life on the planet when a type of mat, “stromatolites,” covered vast areas of primordial seas in the Proterozoic.

The book ends with a chapter devoted to discussing interactions between microbes and higher plants and animals. Symbiosis is sometimes used to describe all interactions, even negative ones, between organisms in persistent, close contact. This chapter focuses on interactions that benefit both partners (mutualism), or one partner while being neutral to the other (commensalism). Microbes are essential to the health and ecology of vertebrates, including Homo sapiens. Microbial cells outnumber human cells on our bodies, aiding in digestion and warding off pathogens. In consortia similar to the anaerobic food chain of anoxic sediments, microbes are essential in the digestion of plant material by deer, cattle, and sheep. Different types of microbes form symbiotic relationships with insects and help to explain their huge success in the biosphere. Protozoa are crucial for wood-boring insects, symbiotic bacteria in the genus Buchnera provide sugars to host aphids while obtaining essential amino acids in exchange, and fungi thrive in subterranean gardens before being harvested for food by ants. Symbiotic dinoflagellates directly provide organic material to support coral growth in exchange for ammonium and other nutrients. Corals are now threatened worldwide by rising oceanic temperatures, decreasing pH, and other human-caused environmental changes. At hydrothermal vents in some deep oceans, sulfur-oxidizing bacteria fuel an entire ecosystem and endosymbiotic bacteria support the growth of giant tube worms. Higher plants also have many symbiotic relationships with bacteria and fungi. Symbiotic nitrogen-fixing bacteria in legumes and other plants fix more nitrogen than free-living bacteria. Fungi associated with plant roots (“mycorrhizal”) are even more common and potentially provide plants with phosphorus as well as nitrogen. Symbiotic microbes can provide other services to their hosts, such as producing bioluminescence, needed for camouflage against predators. In the case of the bobtail squid, bioluminescence is only turned on when populations of the symbiotic bacteria reach critical levels, determined by a quorum sensing mechanism.

Bones are multifunctional passive organs of movement that supports soft tissue and directly attached muscles. They also protect internal organs and are a reserve of calcium, phosphorus and magnesium. Each bone is covered with periosteum, and the adjacent bone surfaces are covered by articular cartilage. Histologically, the bone is an organ composed of many different tissues. The main component is bone tissue (cortical and spongy) composed of a set of bone cells and intercellular substance (mineral and organic), it also contains fat, hematopoietic (bone marrow) and cartilaginous tissue. Bones are a tissue that even in adult life retains the ability to change shape and structure depending on changes in their mechanical and hormonal environment, as well as self-renewal and repair capabilities. This process is called bone turnover. The basic processes of bone turnover are: • bone modeling (incessantly changes in bone shape during individual growth) following resorption and tissue formation at various locations (e.g. bone marrow formation) to increase mass and skeletal morphology. This process occurs in the bones of growing individuals and stops after reaching puberty • bone remodeling (processes involve in maintaining bone tissue by resorbing and replacing old bone tissue with new tissue in the same place, e.g. repairing micro fractures). It is a process involving the removal and internal remodeling of existing bone and is responsible for maintaining tissue mass and architecture of mature bones. Bone turnover is regulated by two types of transformation: • osteoclastogenesis, i.e. formation of cells responsible for bone resorption • osteoblastogenesis, i.e. formation of cells responsible for bone formation (bone matrix synthesis and mineralization) Bone maturity can be defined as the completion of basic structural development and mineralization leading to maximum mass and optimal mechanical strength. The highest rate of increase in pig bone mass is observed in the first twelve weeks after birth. This period of growth is considered crucial for optimizing the growth of the skeleton of pigs, because the degree of bone mineralization in later life stages (adulthood) depends largely on the amount of bone minerals accumulated in the early stages of their growth. The development of the technique allows to determine the condition of the skeletal system (or individual bones) in living animals by methods used in human medicine, or after their slaughter. For in vivo determination of bone properties, Abstract 10 double energy X-ray absorptiometry or computed tomography scanning techniques are used. Both methods allow the quantification of mineral content and bone mineral density. The most important property from a practical point of view is the bone’s bending strength, which is directly determined by the maximum bending force. The most important factors affecting bone strength are: • age (growth period), • gender and the associated hormonal balance, • genotype and modification of genes responsible for bone growth • chemical composition of the body (protein and fat content, and the proportion between these components), • physical activity and related bone load, • nutritional factors: – protein intake influencing synthesis of organic matrix of bone, – content of minerals in the feed (CA, P, Zn, Ca/P, Mg, Mn, Na, Cl, K, Cu ratio) influencing synthesis of the inorganic matrix of bone, – mineral/protein ratio in the diet (Ca/protein, P/protein, Zn/protein) – feed energy concentration, – energy source (content of saturated fatty acids - SFA, content of polyun saturated fatty acids - PUFA, in particular ALA, EPA, DPA, DHA), – feed additives, in particular: enzymes (e.g. phytase releasing of minerals bounded in phytin complexes), probiotics and prebiotics (e.g. inulin improving the function of the digestive tract by increasing absorption of nutrients), – vitamin content that regulate metabolism and biochemical changes occurring in bone tissue (e.g. vitamin D3, B6, C and K). This study was based on the results of research experiments from available literature, and studies on growing pigs carried out at the Kielanowski Institute of Animal Physiology and Nutrition, Polish Academy of Sciences. The tests were performed in total on 300 pigs of Duroc, Pietrain, Puławska breeds, line 990 and hybrids (Great White × Duroc, Great White × Landrace), PIC pigs, slaughtered at different body weight during the growth period from 15 to 130 kg. Bones for biomechanical tests were collected after slaughter from each pig. Their length, mass and volume were determined. Based on these measurements, the specific weight (density, g/cm3) was calculated. Then each bone was cut in the middle of the shaft and the outer and inner diameters were measured both horizontally and vertically. Based on these measurements, the following indicators were calculated: • cortical thickness, • cortical surface, • cortical index. Abstract 11 Bone strength was tested by a three-point bending test. The obtained data enabled the determination of: • bending force (the magnitude of the maximum force at which disintegration and disruption of bone structure occurs), • strength (the amount of maximum force needed to break/crack of bone), • stiffness (quotient of the force acting on the bone and the amount of displacement occurring under the influence of this force). Investigation of changes in physical and biomechanical features of bones during growth was performed on pigs of the synthetic 990 line growing from 15 to 130 kg body weight. The animals were slaughtered successively at a body weight of 15, 30, 40, 50, 70, 90, 110 and 130 kg. After slaughter, the following bones were separated from the right half-carcass: humerus, 3rd and 4th metatarsal bone, femur, tibia and fibula as well as 3rd and 4th metatarsal bone. The features of bones were determined using methods described in the methodology. Describing bone growth with the Gompertz equation, it was found that the earliest slowdown of bone growth curve was observed for metacarpal and metatarsal bones. This means that these bones matured the most quickly. The established data also indicate that the rib is the slowest maturing bone. The femur, humerus, tibia and fibula were between the values of these features for the metatarsal, metacarpal and rib bones. The rate of increase in bone mass and length differed significantly between the examined bones, but in all cases it was lower (coefficient b <1) than the growth rate of the whole body of the animal. The fastest growth rate was estimated for the rib mass (coefficient b = 0.93). Among the long bones, the humerus (coefficient b = 0.81) was characterized by the fastest rate of weight gain, however femur the smallest (coefficient b = 0.71). The lowest rate of bone mass increase was observed in the foot bones, with the metacarpal bones having a slightly higher value of coefficient b than the metatarsal bones (0.67 vs 0.62). The third bone had a lower growth rate than the fourth bone, regardless of whether they were metatarsal or metacarpal. The value of the bending force increased as the animals grew. Regardless of the growth point tested, the highest values were observed for the humerus, tibia and femur, smaller for the metatarsal and metacarpal bone, and the lowest for the fibula and rib. The rate of change in the value of this indicator increased at a similar rate as the body weight changes of the animals in the case of the fibula and the fourth metacarpal bone (b value = 0.98), and more slowly in the case of the metatarsal bone, the third metacarpal bone, and the tibia bone (values of the b ratio 0.81–0.85), and the slowest femur, humerus and rib (value of b = 0.60–0.66). Bone stiffness increased as animals grew. Regardless of the growth point tested, the highest values were observed for the humerus, tibia and femur, smaller for the metatarsal and metacarpal bone, and the lowest for the fibula and rib. Abstract 12 The rate of change in the value of this indicator changed at a faster rate than the increase in weight of pigs in the case of metacarpal and metatarsal bones (coefficient b = 1.01–1.22), slightly slower in the case of fibula (coefficient b = 0.92), definitely slower in the case of the tibia (b = 0.73), ribs (b = 0.66), femur (b = 0.59) and humerus (b = 0.50). Bone strength increased as animals grew. Regardless of the growth point tested, bone strength was as follows femur > tibia > humerus > 4 metacarpal> 3 metacarpal> 3 metatarsal > 4 metatarsal > rib> fibula. The rate of increase in strength of all examined bones was greater than the rate of weight gain of pigs (value of the coefficient b = 2.04–3.26). As the animals grew, the bone density increased. However, the growth rate of this indicator for the majority of bones was slower than the rate of weight gain (the value of the coefficient b ranged from 0.37 – humerus to 0.84 – fibula). The exception was the rib, whose density increased at a similar pace increasing the body weight of animals (value of the coefficient b = 0.97). The study on the influence of the breed and the feeding intensity on bone characteristics (physical and biomechanical) was performed on pigs of the breeds Duroc, Pietrain, and synthetic 990 during a growth period of 15 to 70 kg body weight. Animals were fed ad libitum or dosed system. After slaughter at a body weight of 70 kg, three bones were taken from the right half-carcass: femur, three metatarsal, and three metacarpal and subjected to the determinations described in the methodology. The weight of bones of animals fed aa libitum was significantly lower than in pigs fed restrictively All bones of Duroc breed were significantly heavier and longer than Pietrain and 990 pig bones. The average values of bending force for the examined bones took the following order: III metatarsal bone (63.5 kg) <III metacarpal bone (77.9 kg) <femur (271.5 kg). The feeding system and breed of pigs had no significant effect on the value of this indicator. The average values of the bones strength took the following order: III metatarsal bone (92.6 kg) <III metacarpal (107.2 kg) <femur (353.1 kg). Feeding intensity and breed of animals had no significant effect on the value of this feature of the bones tested. The average bone density took the following order: femur (1.23 g/cm3) <III metatarsal bone (1.26 g/cm3) <III metacarpal bone (1.34 g / cm3). The density of bones of animals fed aa libitum was higher (P<0.01) than in animals fed with a dosing system. The density of examined bones within the breeds took the following order: Pietrain race> line 990> Duroc race. The differences between the “extreme” breeds were: 7.2% (III metatarsal bone), 8.3% (III metacarpal bone), 8.4% (femur). Abstract 13 The average bone stiffness took the following order: III metatarsal bone (35.1 kg/mm) <III metacarpus (41.5 kg/mm) <femur (60.5 kg/mm). This indicator did not differ between the groups of pigs fed at different intensity, except for the metacarpal bone, which was more stiffer in pigs fed aa libitum (P<0.05). The femur of animals fed ad libitum showed a tendency (P<0.09) to be more stiffer and a force of 4.5 kg required for its displacement by 1 mm. Breed differences in stiffness were found for the femur (P <0.05) and III metacarpal bone (P <0.05). For femur, the highest value of this indicator was found in Pietrain pigs (64.5 kg/mm), lower in pigs of 990 line (61.6 kg/mm) and the lowest in Duroc pigs (55.3 kg/mm). In turn, the 3rd metacarpal bone of Duroc and Pietrain pigs had similar stiffness (39.0 and 40.0 kg/mm respectively) and was smaller than that of line 990 pigs (45.4 kg/mm). The thickness of the cortical bone layer took the following order: III metatarsal bone (2.25 mm) <III metacarpal bone (2.41 mm) <femur (5.12 mm). The feeding system did not affect this indicator. Breed differences (P <0.05) for this trait were found only for the femur bone: Duroc (5.42 mm)> line 990 (5.13 mm)> Pietrain (4.81 mm). The cross sectional area of the examined bones was arranged in the following order: III metatarsal bone (84 mm2) <III metacarpal bone (90 mm2) <femur (286 mm2). The feeding system had no effect on the value of this bone trait, with the exception of the femur, which in animals fed the dosing system was 4.7% higher (P<0.05) than in pigs fed ad libitum. Breed differences (P<0.01) in the coross sectional area were found only in femur and III metatarsal bone. The value of this indicator was the highest in Duroc pigs, lower in 990 animals and the lowest in Pietrain pigs. The cortical index of individual bones was in the following order: III metatarsal bone (31.86) <III metacarpal bone (33.86) <femur (44.75). However, its value did not significantly depend on the intensity of feeding or the breed of pigs.