To see the other types of publications on this topic, follow the link: Tření a tloušťka mazacího filmu.
Dissertations / Theses on the topic 'Tření a tloušťka mazacího filmu'
Create a spot-on reference in APA, MLA, Chicago, Harvard, and other styles
Consult the top 25 dissertations / theses for your research on the topic 'Tření a tloušťka mazacího filmu.'
Next to every source in the list of references, there is an 'Add to bibliography' button. Press on it, and we will generate automatically the bibliographic reference to the chosen work in the citation style you need: APA, MLA, Harvard, Chicago, Vancouver, etc.
You can also download the full text of the academic publication as pdf and read online its abstract whenever available in the metadata.
Browse dissertations / theses on a wide variety of disciplines and organise your bibliography correctly.
1
Katrincová, Tereza. "Vliv geometrie textur na tření a utváření mazacího filmu v radiálním kluzném ložisku." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2021. http://www.nusl.cz/ntk/nusl-443753.
Full textAbstract:
The aim of this diploma thesis is to find out how the geometric parameters of circular textures affect the friction and lubrication in a conformal contact. The configuration of a partial, radial, hydrodynamic bearing was investigated on a modified block on-ring device, where the block was replaced by a sapphire section. The device allows simultaneous measurement of friction and optical observation of processes in contact. The light induced fluorescence method was used for the measurement of film thickness. None of the studied texture combinations had a positive effect on the transition from hydrodynamic mode to mixed lubrication mode. Textures in the narrow band of the combination of diameter and depth have a positive effect, outside of them negative effect of texture on friction and film thickness was observed.
2
Strnad, Jan. "Vliv kontaminace a degradace maziva na chování mazacího filmu." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2018. http://www.nusl.cz/ntk/nusl-379037.
Full textAbstract:
Lubrication contamination and degradation is one of the major causes of unexpected failure of tribological nodes. As a result, different levels of maintenance are introduced in practice, leading to a longer service life of the lubricated node. These systems often include sophisticated on-line diagnostic tools that can be used to evaluate a sample of a lubricant using certain variables such as viscosity, number of particles, humidity, dielectric constant, etc. Based on changes of these variables some systems can make corrective measures such as filtering or complete replacement of lubricant. Therefore, the aim of this experimental thesis is to determine the influence of lubrication contamination (solid particles, moisture) and degradation (oxidation) on the lubricating film behavior with respect to its limit bearing capacity. To examine the thickness of the lubricating film, friction and wear, an optical and MTM tribometer, in the ball-on-disc configuration, was used.
3
Urban, Filip. "Experimentální studium tření a mazání TEP kyčle." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2014. http://www.nusl.cz/ntk/nusl-231488.
Full textAbstract:
This work analyzes problems of friction and lubrication of total hip replacement (THR). At first, experimental study of friction coefficient under various conditions was conducted using hip joint simulator based on principle of pendulum. After that, lubrication film development was observed, using colorimetric interferometry with head from THR and glass cup with respect of geometry and clearance to cups made originally for THR. With respect to research study [25] it was found that increasing contact conformity leads to increased film thickness. Also protein adsorption on articulating surfaces was observed. Thanks to adsorption 80 nm film thickness was measured even if relative surface speed was zero. Furthermore protein aggregation was observed on the border of contact zone, similar aggregations were observed by Myant et al. [29] or Vrbka et al. [25]. These aggregations are formed when lubricant is under shear stress and it can positively affect film thickness. If the relative motion of articulating surfaces is not sufficient, the protein layer can`t be refreshed enough and film thickness start decreasing. Coefficient of friction 0,13 was measured when lubricating film development was observed. Close to this value are material combinations metal on polyethylene and metal on metal.
4
Frýza, Josef. "Elastohydrodynamic Film Study under Impact Loading and Lateral Vibrations." Doctoral thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2018. http://www.nusl.cz/ntk/nusl-371778.
Full textAbstract:
Disertační práce se zabývá chováním a odezvou elastohydrodynamického (EHD) mazacího filmu za neustálených provozních podmínek. V úvodní části práce jsou shrnuty poznatky z oblasti EHD mazání; od jeho historie, přes základní mechanismy mazání a používané experimentální metody, až po nedávno publikované studie zaměřené na transientní podmínky. Hlavním cílem práce bylo experimentálně objasnit vliv provozních parametrů a reologických vlastností maziv na chování mazacího filmu v bodovém kontaktu při jeho nárazovém zatěžování a vystavení příčným vibracím. Za tímto účelem byla vyvinuta laboratorní zařízení umožňující měření rozložení mazacího filmu a tření za kontrolovaných nestacionárních podmínek. Experimenty odhalili zásadní roli přibližovacích a zatěžovacích rychlostí na formování stlačených mazacích filmů při nárazovém zatěžování. Výsledky byly srovnávány s nedávným teoretickým řešením. Bylo ukázáno na jeho nedostatky, jež byly následně odstraněny implementací empirických vztahů zohledňujících reologii maziv. V případě příčných vibrací byly nalezeny hranice selhání mazacího filmu a určeny vztahy popisující vliv příčných vibrací na centrální tloušťku filmu a její fluktuace jednotně pro všechny maziva. Závěrečná část práce poskytuje nový pohled na reologii maziv pomocí inovativního přístupu měření třecích reakcí maziva současně ve dvou směrech kontaktu za podmínek příčných vibrací. Tyto původní výsledky rozšiřují pochopení mechanizmů EHD mazání a mohou být použity k dokonalejším návrhům strojů, a vylepšit tak jejich účinnost, spolehlivost a životnost.
5
Sakai, Kazumi. "Study of Correlation between Grease Film Formations and Mechanical Losses on Various Surfaces." Doctoral thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2018. http://www.nusl.cz/ntk/nusl-383527.
Full textAbstract:
Tato disertační práce se zaměřuje na studium závislosti mezi reakčním momentem ložiska mazaného plastickým mazivem s lithným mýdlem a vlastnostmi maziva, jako například tloušťka vytvářeného mazacího filmu, jeho reologie, struktura zpevňovadla, trakční vlastnosti či vliv topografie povrchu. Typ maziva poskytujícího nižší odpor závisí na podmínkách provozu ložiska, zejména rychlosti. Chování mazacího filmu za nízkých rychlostí má vliv na reakční moment ložiska v nízkých rychlostech. Mez toku a trakční chování koreluje s momentem ložiska za vysokých rychlostí. Schopnost zpevňovadla vstupovat do kontaktu má vliv na tloušťku filmu, vzhled kavitační oblasti na výstupu kontaktu a chování hladovění. Důvod vstupu zpevňovadla do kontaktu je jeho chemická struktura. Vysoká polárnost hydroxylových sloučenin zpevňovadla podporuje jeho vtažení kontaktními povrchy. Mazivo s nejvyšší polaritou prokázalo na površích obsahujících denty nejčastější vstup do prostoru dentů. Na základě předchozích pozorování je navržen popis principu mechanismu mazání.
6
Jaroš, Tomáš. "Utváření mazacího filmu v poddajném kontaktu." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2017. http://www.nusl.cz/ntk/nusl-318376.
Full textAbstract:
This diploma thesis deals with the study of film formation in compliant contact. Primary attention is dedicated to the influence of the entrainment speed and slide-to-roll ratio (SRR) on the central film thickness. Based on a research study of the available experimental methods, the fluorescence microscopy was used to achieve the aim of the work. Experiments were realized in ball-on-disk configuration. Firstly, a validation of the method was performed where the solid contact of the ceramic ball and the glass disk was analyzed. Since the measured values were in a good agreement with the theoretical prediction, a ball of NBR rubber material, which is commonly used for production of lip seals and o-rings, was subsequently used. The experimental measurements were performed under pure rolling and rolling/sliding conditions when the entrainment speeds varied in the range from 10 to 400 mm / s. A constant load of 0.2 N was applied. The measured data were then compared to the theoretical predictions for compliant contacts. The results showed that the thickness of the lubricating film gradually increases with increasing entrainment speed, which corresponds to theoretical assumption. Against expectations, evident influence of SRR on the film formation has been observed. In the last part of the thesis the measured data are confronted with previously published studies. Finally, some limitations of this study are discussed and recommendations for further improvement of the used experimental method are suggested.
7
Látal, Roman. "Utváření mazacího filmu u spékaných kovových dílů impregnovaných olejem." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2016. http://www.nusl.cz/ntk/nusl-254462.
Full textAbstract:
This thesis deals with the experimental study of the formation of the lubricating film used for sintered metal parts impregnated with oil. The thickness of the lubricating film in a line contact is measured by the method of optical interferometry of thin lubricating films. In this thesis, the effects of various operating parameters on the formation of the lubricating film are described. The usage of impregnated lubricant leads to insufficient supply of lubricant to the contact. Individual results are significantly influenced by the degree of flooding of the contact area.
8
Kozel, Lubomír. "Výpočty kontaktního tlaku z experimentalně určené tloušťky mazacího filmu." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2009. http://www.nusl.cz/ntk/nusl-228649.
Full textAbstract:
This diploma thesis is engaged in calculation of contact pressure from thickness of lubricating film using Finite Element Method (FEM). Within my diploma thesis were performed the calculations concerning to non-conformal surfaces with a view to elastohydrodynamic lubrication. The simulations were done for disk and ball contact, respectively with burnished finish and also with surface which contains small dent. Flow diagram was designed so that the creation of geometry, boundary conditions and results saving is controlled parametrically. With using parameters it is possible to repeat the calculation when the resolution, geometry, etc. will be changed.
9
Odehnal, Lukáš. "Vývoj součinitele tření a mazacího filmu v implantátu kolenní náhrady v průběhu cyklu chůze." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2021. http://www.nusl.cz/ntk/nusl-442825.
Full textAbstract:
This master´s thesis deals with the experimental analysis of the coefficient of friction and lubrication film in total knee replacement. The experiments are performed on a knee joint simulator, with an implemented module for measuring friction. To observe film formation, fluorescent microscopy is used. The experiments are mainly focused on a detailed description of the influence of parameters occurring during the gait cycle. This approach should significantly help in describing the tribological processes that occur in the total knee replacement. The results confirm previous investigations in terms of axial load, where the coefficient of friction decreases with the increasing load. In the case of lubrication film, no significant changes are observed. On the contrary, while investigating the influence of SRR, noticeable changes in film formation are observed while the coefficient of friction being unaffected. While describing the whole gait cycle, precise results are obtained only in the first half of the cycle as the second half is accompanied by the occurrence of large deviations from a rapid decrease of load. This work provides a better understanding of the field of lubrication film in total knee replacements. Moreover, thanks to the simultaneous measurement of the coefficient of friction and the observation of the contact area, it is possible to draw better conclusions than if the experiments had been carried out separately.
10
Bosák, Dalibor. "Mapování tloušťky mazacího filmu u náhrad velkých kloubů člověka." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2012. http://www.nusl.cz/ntk/nusl-230068.
Full textAbstract:
This master’s thesis describes mechanism of lubricating film forming and its thickness in contact of a metal hip joint ball and a glass disc with chromium layer with presence of bovine serum as substitute of synovial fluid occured in a natural joint. Lubricating film thickness is evaluated by a thin film colorimetric interferometry, results are ploted at graphs representing dependence of lubricating film thickness on experiment duration or on mutual speed of articulating surfaces. There is described the influence of concentration of bovine serum and different kinematic conditions on lubricating film forming. From observed interferograms is apparent the adsorption of proteins to glass disc and femoral head surfaces, denaturation and formation of protein aggregations affecting the residual lubricating film thickness.
11
Zimmerman, Martin. "Chování EHD mazacího filmu při náhlých změnách rychlosti a zatížení." Doctoral thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2011. http://www.nusl.cz/ntk/nusl-233979.
Full textAbstract:
This dissertation is focused on experimental study of lubricant film behavior under transient conditions. For real machine parts such as gears, roller bearings and cam mechanism the operating conditions such as speed, load and radius of curvature of rubbing surfaces are vary during the working cycle. Change in operating conditions may pose an increased risk of the lubricating film breakdown. Direct contact of rubbing surfaces at the time of the lubricating film breakdown causes an increase in friction and wear. The high-speed CMOS camera was used to record the dynamic changes in lubricating film thickness during the experiment. The optical interferometry method has been used for reverse reconstruction of lubricating film thickness of the recorded interferograms. It was confirmed that the operating parameters have a major impact on the formation of lubricant film and its thickness and a certain combination of boundary conditions can cause lubricating film rupture. The obtained results showed, that modified topography of the rubbing surfaces can help to increase the lubrication film thickness especially in critical phases of working cycle.
12
Košťál, David. "Studium utváření mazacích filmů za podmínek nedostatečného zásobování kontaktu mazivem." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2011. http://www.nusl.cz/ntk/nusl-229431.
Full textAbstract:
The purpose of this thesis is to reveal production mechanisms of lubrication films between non-conformal surfaces in situations, when is not possible to designate lubrication regime as fully flooded elastohydrodynamic contact. Under certain conditions of lubrication volume, rolling speeds, temperatures, lubrication properties or loads could lubrication film decrease under values determined by fully flooded formulas. This regime is designated as starvation at it includes risk of increased wear. In this thesis the methodology and the new simulator of starving contact are described. Obtained film thickness results are compared with existing numerical models.
13
Adam, Jakub. "Chování mazaných kontaktů za vysokých skluzů." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2018. http://www.nusl.cz/ntk/nusl-379035.
Full textAbstract:
The aim of this diploma thesis is to describe the influence of individual operating parameters on thickness and temperature distribution of elastohydrodynamic contact under high slip ratio. In this work, the distribution of the lubricant film thickness is determined by optical interferometry and the temperature mapping in EHL contact is realized by infrared microscopy. Two optical filters were used to separate the radiation of contact surfaces and oil. Temperature of disk surface was measured using a sapphire disk with chromium layer that shielded radiation from ball and oil. The experimental device was modified to simulate the conditions of the various vectors between entrainment and sliding speed. The results extend existing information about behavior of EHL contact under high slip ratio conditions.
14
Matoušek, Kamil. "Vliv povrchových rýh na mazání bodových kontaktů." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2015. http://www.nusl.cz/ntk/nusl-231945.
Full textAbstract:
This diploma thesis deals with experimental study of the effect of surface grooves on distribution of lubricant film in elastohydrodynamic lubricated point contact. Lubricant film thickness was measured by ball-on-disc apparatus using an optical interferometry technique - thin film colorimetric interferometry. The effects of groove geometry, lubricant and operating conditions were studied in this diploma thesis. The effects of these variables are evaluated based on newly suggested parameter Rgi (groove influence ratio). Groove influence ratio is defined as an influenced film thickness influenced by groove divided by film thickness for smooth surfaces.
15
Ali, Fadi. "Effect of Surface Texturing on Friction and Film Thickness under Starved Lubrication Conditions." Doctoral thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2015. http://www.nusl.cz/ntk/nusl-234247.
Full textAbstract:
Tato disertační práce se zabývá vlivem mělkých mikro-textur na tření a tloušťku filmu v mazaných nekonformních kontaktech za extrémních podmínek a za podmínek hladovění kontaktu. Měření byla realizována na tribometru v konfiguraci ball-on-disk. Kontakt byl pozorován pomocí vysokorychlostní kamery. Pro stanovení součinitele tření byl využit snímač krouticího momentu. V této studii byly popsány dva typy mikrotextur – mikrovtisky a příčné mikrodrážky. Výsledky naznačují, že za podmínek hladovění vedou mikrovtisky ke snížení tření a to díky nárůstu tloušťky mazacího filmu. Mechanismus doplňování mikrovtisků čerstvým mazivem je pravděpodobně způsoben kapilárními jevy ve vstupní oblasti. Třecí plochy s příčnými mikrodrážkami, jejichž délka byla menší než průměr Hertzova kontaktu, potom obecně vykazovaly lepší tribologické parametry ve srovnání s hladkými povrchy. Příčné mikrodrážky vedly k výraznému nárůstu tloušťky mazacího filmu za podmínek hladovění i za extrémních provozních podmínek (protisměrný pohyb). Numerické simulace přechodových jevů příčných mikrodrážek ukázaly dobrou shodu s experimentálními výsledky.
16
Polnický, Vojtěch. "Konstrukce simulátoru kolenního kloubu." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2017. http://www.nusl.cz/ntk/nusl-318786.
Full textAbstract:
The diploma thesis is focused on the design and realization of an experimental device. The purpose of device is the simulation of dynamic and kinematic conditions of knee replacement during the walking cycle. The simulator will be used to study the formation of the lubricating film in contact of the femoral component and the polyethylene spacer, and to the cyclic wear tests for knee replacements. First part of thesis is focused on the description of working parameters of knee replacements and analysis of knee joint simulators. The description of conceptual design and selection of the final variation follows. The final design allows simulation of dynamic and kinematic conditions of ISO 14 243-3. Creation of lubricating film is analyzed by the non-contact optical fluorescence microscopy method. The work includes complete drawing documentation, wiring diagram, verification of the functionality of the device and detailed operating instructions.
17
Chlachula, Petr. "Cílená modifikace topografie třecích povrchů." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2009. http://www.nusl.cz/ntk/nusl-228784.
Full textAbstract:
Surface texturing of rubbing surfaces represents the way how to increase tribological performances by improving the lubrication film formation and diminishing friction and wear. Its application in machine components requires detailed understanding of the mechanism taking place between rubbing surfaces in microscopic scale. This diploma thesis is focused on the processes taking place in tribology systems to consider the possibility of surface texturing applications in highly loaded machine parts operated under transient operational conditions.
18
Puchner, Jiří. "Vliv cílené modifikace topografie na elastohydrodynamické mazací filmy." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2008. http://www.nusl.cz/ntk/nusl-227909.
Full textAbstract:
Diploma thesis describes analysis of influence of surface texturing on non-conformal rubbing surfaces. High speed camera was used to observe the effect of micro-dents of various depths on film thickness under pure rolling and rolling/sliding conditions. It can be concluded from the obtained results that micro-texture of suitable sizes can results in film thickness increase without lubrication film breakdown.
19
Košťál, David. "Experimentální studium utváření mazacích filmů za podmínek nedostatečného zásobování kontaktu mazivem." Doctoral thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2015. http://www.nusl.cz/ntk/nusl-234614.
Full textAbstract:
The dissertation thesis deals with an experimental study of an elastohydrodynamic contact under insufficient lubricant supply. Theoretical studies published in this research area focus mainly on the development of theoretical models and there is an insufficient number of experimental studies which validate these models. There are two basic methods of starvation severity control in published theoretical models: by positioning of an inlet meniscus and by setting the thickness of an oil layer in the vicinity of contact inlet. The second method is more suitable when considering a wide range of operating conditions, however it is difficult to ensure experimentally. This thesis presents original experimental results and aims to describe the starvation severity level as a function of the inlet film thickness. Deeper understanding of fundamental processes in starved elastohydrodynamic contacts enables the development of more precise models, better ability of prediction of the starvation and improves the ability to avoid starvation in the early design process of key tribological components.
20
Popelka, Michal. "Studium přechodových jevů mezi zcela zaplaveným a hladovějícím elastohydrodynamicky mazaným kontaktem." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2012. http://www.nusl.cz/ntk/nusl-230142.
Full textAbstract:
The diploma thesis deals with The study of transition between fully flooded and starved regimes in EHL Contact. The work is focused on problems of starved contact and surface texturing of rubbing surfaces. Surface texturing of rubbing surfaces is one of the adjustments that cause in a sense improved lubricity and reduce friction and wear. The aim of this study is to compare numerical models with real experimental results measured on the Experimental apparatus.
21
Šperka, Petr. "In-situ studium změny topografie třecích povrchů v elastohydrodynamickém kontaktu." Doctoral thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2011. http://www.nusl.cz/ntk/nusl-233978.
Full textAbstract:
This dissertation thesis deals with elastohydrodynamic lubrication (EHL) of surfaces with real roughness. Systematic study of surface harmonic components behaviour, during their passage of the EHL contact, by other authors led to retrieval of a uniform principle according which individual harmonic components deform inside the contact. Although the amplitude attenuation model can provide rapid tool for more accurate surface assessment in design process it has not been validated on real surfaces till now. The thesis represents pioneering work on quantitative analysis of real surfaces EHD measurements. It contains original and new results with real and model roughness features that in many cases confirm theoretical expectations. Deeper understanding of surface roughness behaviour inside EHL contact, which is typical for machine parts like bearings, gears, cams etc., can help to improve design process of the components and ultimately enable machines and equipment to work with lower energy requirements and higher durability.
22
Jordán, Jakub. "Vliv cílené modifikace topografie na nedostatečně mazaný kontakt." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2010. http://www.nusl.cz/ntk/nusl-229252.
Full textAbstract:
The diploma thesis deals with the analysis of the effects surface texturing on starved contact. Experimental verification was realized on apparatus simulating contact between a steel ball and glass disc using colorimetric interferometry and high-speed camera. The work deals with lubrication regimes, problems with starved contacts and surface texturing which can reduce effects of starvation on non-conformal surface contacts.
23
Svoboda, Petr. "Experimentální studium utváření mazacích filmů při reverzaci a rozběhu třecích povrchů." Doctoral thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2009. http://www.nusl.cz/ntk/nusl-233855.
Full textAbstract:
This dissertation is focused on the effects of both artificially produced and real roughness features on mixed lubrication film formation during start-up and reversal of non-conformal contacts operated under rolling/sliding conditions. The start-up operation of mixed lubricated contacts represents one of the transient conditions that bring the risk of the surface damage because of asperities interactions. Chromatic interferograms captured by CMOS high-speed camera during start up of the motion enabled to observe the detailed changes in lubrication film caused by surface features. The observation of the effects of surface dents artificially produced on the ball surface helped to understand better the behaviour of real surface topography. It was found that the presence of shallow surface features can help to separate mixed lubricated rubbing surfaces more efficiently than it could be suggested from the results obtained with smooth surfaces. It can be suggested from the obtain results that properly designed topography of the rubbing surfaces can help to reduce the asperities interactions under transient operational conditions.
24
Omasta, Milan. "Studium utváření elastohydrodynamických mazacích filmů u hypoidních převodů." Doctoral thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2013. http://www.nusl.cz/ntk/nusl-234175.
Full textAbstract:
This PhD thesis deals with elastohydrodynamic lubrication (EHL) under the conditions that occur between mated hypoid gear teeth. The aim is to describe experimentally the behaviour of lubricating film and mechanisms of its formation. The focus is mainly placed on clarifying the influence of direction and magnitude of sliding velocity in circular and elliptical contacts. Generally, it is still assumed that the direction of sliding velocity has no effect on the resulting lubricant film. In this study optical interferometry is used to determine distribution of lubricant film thickness. This work includes new and original results which clarify the studied problem. It was found that the direction of sliding velocity affects shape of the film at high speeds. This relates to the effect on heat flow through the contact. The results have an impact on the development of general EHL theory and provide knowledge applicable in film thickness prediction in the design of real tribological nodes.
25
Hartl, Petr. "Mazaní plastových ozubených soukolí." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2020. http://www.nusl.cz/ntk/nusl-417769.
Full textAbstract:
The work deals with the process of lubrication of gears from a combination of materials that have significantly different material properties. The experimental measurement is performed on a tribometer in simulated gear contact with a ball-disk configuration. The Chromatic Optical Interferometry method is used to measure the formation of a lubricating film in contact. The purpose of this work is to clarify the process of film thickness formation and compare experimental measurements with predictions, which are valid in Soft EHL regime.