Dissertations / Theses: 'Shock (Mechanics) – Mathematical models'

1

Handley, Caroline A. "Numerical modelling of two HMX-based plastic-bonded explosives at the mesoscale." Thesis, University of St Andrews, 2011. http://hdl.handle.net/10023/1709.

Full text

Abstract:

Mesoscale models are needed to predict the effect of changes to the microstructure of plastic-bonded explosives on their shock initiation and detonation behaviour. This thesis describes the considerable progress that has been made towards a mesoscale model for two HMX-based explosives PBX9501 and EDC37. In common with previous work in the literature, the model is implemented in hydrocodes that have been designed for shock physics and detonation modelling. Two relevant physics effects, heat conduction and Arrhenius chemistry, are added to a one-dimensional Lagrangian hydrocode and correction factors are identified to improve total energy conservation. Material models are constructed for the HMX crystals and polymer binders in the explosives, and are validated by comparison to Hugoniot data, Pop-plot data and detonation wave profiles. One and two-dimensional simulations of PBX9501 and EDC37 microstructures are used to investigate the response of the bulk explosive to shock loading. The sensitivity of calculated temperature distributions to uncertainties in the material properties data is determined, and a thermodynamic explanation is given for time-independent features in temperature profiles. Hotspots are widely accepted as being responsible for shock initiation in plastic-bonded explosives. It is demonstrated that, although shock heating of crystals and binder is responsible for temperature localisation, it is not a feasible hotspot mechanism in PBX9501 and EDC37 because the temperatures generated are too low to cause significant chemical reaction in the required timescales. Critical hotspot criteria derived for HMX and the binders compare favourably to earlier studies. The speed of reaction propagation from hotspots into the surrounding explosive is validated by comparison to flame propagation data, and the temperature of the gaseous reaction products is identified as being responsible for negative pressure dependence. Hotspot size, separation and temperature requirements are identified which can be used to eliminate candidate mechanisms in future.

APA, Harvard, Vancouver, ISO, and other styles

2

Rhedin, Kristoffer, and Sjödin Simon Mattsson. "Vätskeslag i rörsystem : Experimentell utvärdering av rörstödens samt rörets utformning och dess inverkan på vätskeslag i rörsystem." Thesis, Linnéuniversitetet, Sjöfartshögskolan (SJÖ), 2018. http://urn.kb.se/resolve?urn=urn:nbn:se:lnu:diva-74304.

Full text

Abstract:

Studiens syfte är att identifiera en robust ingenjörsmetodik för approximation av sannolikhet och konsekvens (risken) vid vätskeslag i ett specifikt rörsystem. Arbetet har utförts i form av kvalitativa studier med verifierande experiment av analytiska beräkningsresultat. Studiens resultat, vilka presenteras och diskuteras i slutsatskapitlet, visar på att vätskeslag kan predikteras och därigenom förebyggas med Joukowskys ekvation, vilken formulerades av Johannes von Kries 1883. I de flesta fall kan ett rörsystems konstruktion optimeras mot oönskade tryckslags-konsekvenser genom omsorgsfullt val av lämpliga rörsystemskomponenter, såsom rördimensioner, ventiler, rörkrökningsradier och rörstödskonstruktioner.
This study’s objective has been to identify and evaluate a robust engineering method for the purpose of approximation and evaluation of a water hammer event in a specific pipe system design. The study has been conducted in the form of qualitative studies with verifying experiments of the results from various analytical calculations. The results presented and discussed in the last chapter of the essay, indicates that water hammer can be predicted and prevented by using Joukowsky's equation, formulated Johannes von Kries 1883. In the most circumstances, pipe systems can be optimized to prevent water hammer consequences by selection of suitable components. Such as tube dimensions, valves, tube bending radius and the tube support design.

APA, Harvard, Vancouver, ISO, and other styles

3

Warren, Paul A. "Mathematical models of 3-D ocular mechanics and control." Thesis, University of Sheffield, 1999. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.312221.

Full text

APA, Harvard, Vancouver, ISO, and other styles

4

Lee, M. E. M. "Mathematical models of the carding process." Thesis, University of Oxford, 2001. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.249543.

Full text

Abstract:

Carding is an essential pre-spinning process whereby masses of dirty tufted fibres are cleaned, disentangled and refined into a smooth coherent web. Research and development in this `low-technology' industry have hitherto depended on empirical evidence. In collaboration with the School of Textile Industries at the University of Leeds, a mathematical theory has been developed that describes the passage of fibres through the carding machine. The fibre dynamics in the carding machine are posed, modelled and simulated by three distinct physical problems: the journey of a single fibre, the extraction of fibres from a tuft or tufts and many interconnecting, entangled fibres. A description of the life of a single fibre is given as it is transported through the carding machine. Many fibres are sparsely distributed across machine surfaces, therefore interactions with other neighbouring fibres, either hydrodynamically or by frictional contact points, can be neglected. The aerodynamic forces overwhelm the fibre's ability to retain its crimp or natural curvature, and so the fibre is treated as an inextensible string. Two machine topologies are studied in detail, thin annular regions with hooked surfaces and the nip region between two rotating drums. The theoretical simulations suggest that fibres do not transfer between carding surfaces in annular machine geometries. In contrast to current carding theories, which are speculative, a novel explanation is developed for fibre transfer between the rotating drums. The mathematical simulations describe two distinct mechanisms: strong transferral forces between the taker-in and cylinder and a weaker mechanism between cylinder and doffer. Most fibres enter the carding machine connected to and entangled with other fibres. Fibres are teased from their neighbours and in the case where their neighbours form a tuft, which is a cohesive and resistive fibre structure, a model has been developed to understand how a tuft is opened and broken down during the carding process. Hook-fibre-tuft competitions are modelled in detail: a single fibre extracted from a tuft by a hook and diverging hook-entrained tufts with many interconnecting fibres. Consequently, for each scenario once fibres have been completely or partially extracted, estimates can be made as to the degree to which a tuft has been opened-up. Finally, a continuum approach is used to simulate many interconnected, entangled fibre-tuft populations, focusing in particular on their deformations. A novel approach describes this medium by density, velocity, directionality, alignment and entanglement. The materials responds to stress as an isotropic or transversely isotropic medium dependent on the degree of alignment. Additionally, the material's response to stress is a function of the degree of entanglement which we describe by using braid theory. Analytical solutions are found for elongational and shearing flows, and these compare very well with experiments for certain parameter regimes.

APA, Harvard, Vancouver, ISO, and other styles

5

Moore, Matthew Richard. "New mathematical models for splash dynamics." Thesis, University of Oxford, 2014. http://ora.ox.ac.uk/objects/uuid:c94ff7f2-296a-4f13-b04b-e9696eda9047.

Full text

Abstract:

In this thesis, we derive, extend and generalise various aspects of impact theory and splash dynamics. Our methods throughout will involve isolating small parameters in our models, which we can utilise using the language of matched asymptotics. In Chapter 1 we briefly motivate the field of impact theory and outline the structure of the thesis. In Chapter 2, we give a detailed review of classical small-deadrise water entry, Wagner theory, in both two and three dimensions, highlighting the key results that we will use in our extensions of the theory. We study oblique water entry in Chapter 3, in which we use a novel transformation to relate an oblique impact with its normal-impact counterpart. This allows us to derive a wide range of solutions to both two- and three-dimensional oblique impacts, as well as discuss the limitations and breakdown of Wagner theory. We return to vertical water-entry in Chapter 4, but introduce the air layer trapped between the impacting body and the liquid it is entering. We extend the classical theory to include this air layer and in the limit in which the density ratio between the air and liquid is sufficiently small, we derive the first-order correction to the Wagner solution due to the presence of the surrounding air. The model is presented in both two dimensions and axisymmetric geometries. In Chapter 5 we move away from Wagner theory and systematically derive a series of splash jet models in order to find possible mechanisms for phenomena seen in droplet impact and droplet spreading experiments. Our canonical model is a thin jet of liquid shot over a substrate with a thin air layer trapped between the jet and the substrate. We consider a variety of parameter regimes and investigate the stability of the jet in each regime. We then use this model as part of a growing-jet problem, in which we attempt to include effects due to the jet tip. In the final chapter we summarise the main results of the thesis and outline directions for future work.

APA, Harvard, Vancouver, ISO, and other styles

6

Huang, Xin, and 黃昕. "Exploring critical-state behaviour using DEM." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 2014. http://hdl.handle.net/10722/206742.

Full text

Abstract:

The critical state soil mechanics (CSSM) framework originally proposed by Schofield & Wroth (1968) has been shown to capture the mechanical behaviour of soils effectively. The particulate implementation of the discrete element method (DEM) can replicate many of the complex mechanical characteristics associated with sand. This research firstly shows that the CSSM framework is useful to assess whether a DEM simulation gives a response that is representative of a real soil. The research then explores the capacity of DEM to extend understanding of soil behaviour within the CSSM framework. The influence of sample size on the critical-state response observed in DEM simulations that use rigid-wall boundaries was examined. The observed sensitivity was shown to be caused by higher void ratios and lower contact densities adjacent to the boundaries. When the void ratio (e) and mean stress (p’) of the homogeneous interior regions were considered, the influence of sample size on the position of the critical state line (CSL) in e-log(p’) space diminished. A parametric study on the influence of the interparticle friction (μ) on the load-deformation response was carried out. The macro-scale stress-deformation characteristics were nonlinearly related to μ and the particle-scale measures (fabric, contact force distribution, etc.) varied systematically with μ. The limited effect of increases in μ on the overall strength at high μ values (μ>0.5) is attributable to transition from sliding-dominant to rolling-dominant contact behaviour. A μ value higher than 0.5 leads to a CSL in e-log(p’) space that does not capture real soil response. True-triaxial simulations with different intermediate stress ratios (b) were performed. The dependency of strength on b agreed with empirical failure criteria for sands and was related to a change of buckling modes of the strong force chains as b increased. DEM simulations showed that the position of the CSL in e-log(p’) space depends on the intermediate stress ratio b. This sensitivity seems to be related to the dependency of the directional fabric anisotropy on b. The link between the state parameter and both soil strength and dilatancy proposed by Jefferies & Been (2006) was reproduced in DEM simulations. A new rotational resistance model was proposed and it was shown that the new model can qualitatively capture the influence of particle shape on the mechanical behaviour of sand. However, it was shown that the effect of rotational resistance is limited and to quantitatively compare the DEM simulation results with laboratory testing data, e.g., the critical-state loci, it is necessary to use non-spherical particles.
published_or_final_version
Civil Engineering
Doctoral
Doctor of Philosophy

APA, Harvard, Vancouver, ISO, and other styles

7

Beckham, Jon Regan. "Analysis of mathematical models of electrostatically deformed elastic bodies." Access to citation, abstract and download form provided by ProQuest Information and Learning Company; downloadable PDF file, 169 p, 2008. http://proquest.umi.com/pqdweb?did=1475178561&sid=27&Fmt=2&clientId=8331&RQT=309&VName=PQD.

Full text

APA, Harvard, Vancouver, ISO, and other styles

8

Morland, Lawrence Christopher. "Mathematical models for a fluid flow arising in turbine blade cooling passages." Thesis, University of Oxford, 1988. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.330029.

Full text

APA, Harvard, Vancouver, ISO, and other styles

9

Beylin, Andrey V. "Supersymmetric Landau Models." Scholarly Repository, 2011. http://scholarlyrepository.miami.edu/oa_dissertations/624.

Full text

Abstract:

This work is focused on the different supersymmetric extensions of the Landau model. We aim to fully solve each model and describe its energy levels, wavefunctions, Hilbert space and define a norm on it, as well as find symmetry generators and transformations with respect to them. Several possible generalizations were considered before. It was found for Landau model on the so called Superflag manifold as well as planar Superflag and Superplane Landau models that standard norm on the Hilbert space is not positive definite. Later for planar cases it was found that it is possible to fix this by introducing a new norm which will be invariant and positive definite. Surprisingly this procedure brings up "hidden" symmetries for the known super Landau models. In the dissertation we apply the same procedure for Landau model on superpshere and Superflag manifolds. It turns out that superpsherical Landau model is equivalent to the Superflag model with one of the parameters fixed. Because the model on superpshere can be recovered from the Superflag we will do calculations of corrected norm only for the Superflag. After this we develop a different generalization of the Superplane Landau model. Starting with Lagrangian in a superfield form we introduce two arbitrary functions of superfields K(Φ) and V(Φ) into the Lagrangian. We follow with the component form of Lagrangian. The quantization of the model is possible, and we will show that there is a reparametrization which turn equation of motion of the first scheme into the second set. Standard metric is again non-positive definite and we apply already known procedure to correct it. It will not be possible to solve Schrodinger equations in general with undefined K and V, so we consider one specific case which give us Landau model on a sphere with N = 2 supersymmetry, which put it apart from the superspherical Landau model, which have a superpshere for a target space but do not possess supersymmetry.

APA, Harvard, Vancouver, ISO, and other styles

10

Zhao, Qian, and 赵倩. "A thermomechanical approach to constitutive modeling of geomaterials." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 2011. http://hub.hku.hk/bib/B47166836.

Full text

Abstract:

Modeling of the mechanical behavior of geomaterials is a fundamental yet very difficult problem in geotechnical engineering. The difficulty lies in that the engineering behavior of geomaterials is strongly nonlinear and anisotropic, depending on confining pressure, void ratio, stress history, and drainage conditions. A traditional approach to the modeling of geomaterials is to formulate empirical equations to fit experimental data. Generally, this approach is not able to provide physical insights into the diverse responses observed in the soil mechanics laboratories. Another conventional approach is to make use of the classical plasticity theory, established mainly for metals, to develop constitutive models for geomaterials. While this approach is capable of shedding light on the mechanisms involved, it has been recognized that such models may violate the basic laws of physics. The objective of this thesis is to apply a new approach to constructing constitutive models for geomaterials, by making use of thermomechanical principles. The essence of the new approach is that the constitutive behavior of geomaterials can be completely determined once two thermomechanical potentials, i.e. the free energy and dissipation rate functions, are specified. The yield function and flow rule in the classical plasticity theory can be established from the two potentials, and the models so derived satisfy the basic laws of physics automatically. In this thesis, the theoretical framework for constructing thermomechanical models is introduced. Several concepts in relation to plastic work, dissipated and stored energy are discussed. Both the isotropic and anisotropic models are formulated and realized in this framework and the generated predictions are compared with the test data of a series of triaxial compression tests on sand. To address the important density- and pressure-dependent behaviors of sand in the framework, a state-dependent thermomechanical model is developed, by introducing the state parameter into the dissipation rate function such that a unique set of model parameters is able to predict the behaviors of sand for a wide variation of densities and pressures. Finally, a thermomechanical model for predicting the complex unloading and reloading behaviors of sand is developed by modifying the hardening laws, and the performance of this model is investigated.
published_or_final_version
Civil Engineering
Master
Master of Philosophy

APA, Harvard, Vancouver, ISO, and other styles

11

He, Shu Yu. "Field study on influence of atmospheric parameters and vegetation on variation of soil suction around tree vicinity." Thesis, University of Macau, 2018. http://umaclib3.umac.mo/record=b3868734.

Full text

APA, Harvard, Vancouver, ISO, and other styles

12

Gilpin, Richard. "The numerical solution and analysis of mathematical models for bubbly two-phase flow." Thesis, University of Oxford, 2003. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.289348.

Full text

APA, Harvard, Vancouver, ISO, and other styles

13

Gaballa, Mohamed Abdelrhman Ahmed. "Nonlinear multiphasic mechanics of soft tissue using finite element methods." Diss., The University of Arizona, 1989. http://hdl.handle.net/10150/184837.

Full text

Abstract:

The purpose of the research was to develop a quantitative method which could be used to obtain a clearer understanding of the time-dependent fluid filteration and load-deformation behavior of soft, porous, fluid filled materials (e.g. biological tissues, soil). The focus of the study was on the development of a finite strain theory for multiphasic media and associated computer models capable of predicting the mechanical stresses and the fluid transport processes in porous structures (e.g. across the large blood vessels walls). The finite element (FE) formulation of the nonlinear governing equations of motion was the method of solution for a poroelastic (PE) media. This theory and the FE formulations included the anisotropic, nonlinear material; geometric nonlinearity; compressibility and incompressibility conditions; static and dynamic analysis; and the effect of chemical potential difference across the boundaries (known as swelling effect in biological tissues). The theory takes into account the presence and motion of free water within the biological tissue as the structure undergoes finite straining. Since it is well known that biological tissues are capable of undergoing large deformations, the linear theories are unsatisfactory in describing the mechanical response of these tissues. However, some linear analyses are done in this work to help understand the more involved nonlinear behavior. The PE view allows a quantitative prediction of the mechanical response and specifically the pore pressure fluid flow which may be related to the transport of the macromolecules and other solutes in the biological tissues. A special mechanical analysis was performed on a representative arterial walls in order to investigate the effects of nonlinearity on the fluid flow across the walls. Based on a finite strain poroelastic theory developed in this work; axisymmetric, plane strain FE models were developed to study the quasi-static behavior of large arteries. The accuracy of the FE models was verified by comparison with analytical solutions wherever is possible. These numerical models were used to evaluate variables and parameters, that are difficult or may be impossible to measure experimentally. For instance, pore pressure distribution within the tissue, relative fluid flow; deformation of the wall; and stress distribution across the wall were obtained using the poroelastic FE models. The effect of hypertension on the mechanical response of the arterial wall was studied using the nonlinear finite element models. This study demonstrated that the finite element models are powerful tools for the study of the mechanics of complicated structures such as biological tissue. It is also shown that the nonlinear multiphasic theory, developed in this thesis, is valid for describing the mechanical response of biological tissue structures under mechanical loadings.

APA, Harvard, Vancouver, ISO, and other styles

14

Modarres, Najafabadi Seyed Ali. "Dynamics modelling and analysis of impact in multibody systems." Thesis, McGill University, 2008. http://digitool.Library.McGill.CA:80/R/?func=dbin-jump-full&object_id=115886.

Full text

Abstract:

In this thesis, we discuss a novel approach to the dynamics modelling and analysis of impact in unilaterally constrained multibody systems. This approach is based on an analysis of energy absorption and restitution during impact, using a decomposition technique, which decouples the kinetic energy associated with the spaces of admissible and constrained motions of unilateral contacts. This is done based on the decomposition of the tangent space of the configuration manifold at the pre-impact instant. The decomposition of the kinetic energy can provide a picture of how the energy absorption and dissipation during impact is related to the variation of the generalized velocities and the configuration of multibody systems.
Further, based on the above analysis approach, we introduce a new interpretation of the energetic coefficient of restitution, specially applicable to contact involving multibody systems. This interpretation generalizes the concept of the energetic coefficient of restitution and allows for consideration of simultaneous multiple-point contact scenarios. Moreover, based on the concept of the generalized energetic coefficient of restitution, the contact modes and the post-impact state of planar single-point impact are determined. Further, the problem of simultaneous multiple-point impact is considered, where it is shown that our approach can also be advantageous to characterize the dynamics of interaction in such systems.
The use and applicability of the approach reported are further investigated by conducting an experimental study on a robotic testbed. The open architecture of the testbed allows us to perform various contact experiments, such as single- and multiple-point impact scenarios, with different pre-impact configurations and velocities. The kinematic and dynamic models of the system have been developed and implemented for real-time analysis. It is shown that impact between multibody systems is considerably affected by not only the local dynamics characteristics of the interacting bodies, but also the (global) configuration of the interacting multibody systems. The reported results suggest that the material presented herein offers a useful means to characterize impact in complex systems.

APA, Harvard, Vancouver, ISO, and other styles

15

黃小華 and Siu-wah Wong. "Predicition of fatigue crack propagation using strain energy density method." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 1989. http://hub.hku.hk/bib/B31209506.

Full text

APA, Harvard, Vancouver, ISO, and other styles

16

馮錦生 and Kam-sang Fung. "Fatigue crack propagation with strain energy density approach." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 1989. http://hub.hku.hk/bib/B31209713.

Full text

APA, Harvard, Vancouver, ISO, and other styles

17

陳幸福 and Xingfu Chen. "A ductile damage model based on endochronic theory and its applicationto ductile failure analysis." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 1993. http://hub.hku.hk/bib/B31233004.

Full text

APA, Harvard, Vancouver, ISO, and other styles

18

Murphy, Ryan John. "Mechanochemical and experimental models in mathematical biology." Thesis, Queensland University of Technology, 2022. https://eprints.qut.edu.au/228428/1/Ryan%20John_Murphy_Thesis.pdf.

Full text

Abstract:

Experiments that probe epithelial tissue dynamics, cell competition, and tumour growth are fundamental to understand processes in developmental biology, cancer progression and treatment. However, interpreting complex biological experiments is challenging. To address this challenge, we develop and use a range of mathematical models. First, we focus on epithelial tissue dynamics. Second, we use real-time cell cycle imaging to reveal the structure of growing tumour spheroids. We then revisit the seminal Greenspan tumour growth model and use statistical analysis to quantitatively connect it to experimental data for the first time to reveal experimental design choices that lead to reliable biological insight.

APA, Harvard, Vancouver, ISO, and other styles

19

Ching, Wing-han Michael, and 程永鏗. "Modeling of contaminant dispersion by statistical mechanics." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 2009. http://hub.hku.hk/bib/B42664500.

Full text

APA, Harvard, Vancouver, ISO, and other styles

20

Chen, Wenqin, and 陳文欽. "An analytical shock-fitting approach to the solution of the Lighthill-Whitham-Richards traffic flow model." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 2007. http://hub.hku.hk/bib/B38724650.

Full text

APA, Harvard, Vancouver, ISO, and other styles

21

Tang, Baobao. "Development of Mathematical and Computational Models to Design Selectively Reinforced Composite Materials." Thesis, University of Louisiana at Lafayette, 2016. http://pqdtopen.proquest.com/#viewpdf?dispub=10163313.

Full text

Abstract:

Different positions of a material used for structures experience different stresses, sometimes at both extremes, when undergoing processing, manufacturing, and serving. Taking the three-point bending as an example, the plate experiences higher stress in the middle span area and lower stress in both sides of the plate. In order to ensure the performance and reduce the cost of the composite, placement of different composite material with different mechanical properties, i.e. selective reinforcement, is proposed.

Very few study has been conducted on selective reinforcement. Therefore, basic understanding on the relationship between the selective reinforcing variables and the overall properties of composite material is still unclear and there is still no clear methodology to design composite materials under different types of loads.

This study started from the analysis of composite laminate under three point bending test. From the mechanical analysis and simulation result of homogeneously reinforced composite materials, it is found that the stress is not evenly distributed on the plate based on through-thickness direction and longitudinal direction. Based on these results, a map for the stress distribution under three point bending was developed. Next, the composite plate was selectively designed using two types of configurations. Mathematical and finite element analysis (FEA) models were built based on these designs. Experimental data from tests of hybrid composite materials was used to verify the mathematical and FEA models. Analysis of the mathematical model indicates that the increase in stiffness of the material at the top and bottom surfaces and middle-span area is the most effective way to improve the flexural modulus in three point bending test. At the end of this study, a complete methodology to perform the selective design was developed.

APA, Harvard, Vancouver, ISO, and other styles

22

Keita, Sana. "Eulerian Droplet Models: Mathematical Analysis, Improvement and Applications." Thesis, Université d'Ottawa / University of Ottawa, 2018. http://hdl.handle.net/10393/37907.

Full text

Abstract:

The Eulerian description of dispersed two-phase flows results in a system of partial differential equations describing characteristics of the flow, namely volume fraction, density and velocity of the two phases, around any point in space over time. When pressure forces are neglected or a same pressure is considered for both phases, the resulting system is weakly hyperbolic and solutions may exhibit vacuum states (regions void of the dispersed phase) or localized unbounded singularities (delta shocks) that are not physically desirable. Therefore, it is crucial to find a physical way for preventing the formation of such undesirable solutions in weakly hyperbolic Eulerian two-phase flow models. This thesis focuses on the mathematical analysis of an Eulerian model for air- droplet flows, here called the Eulerian droplet model. This model can be seen as the sticky particle system with a source term and is successfully used for the prediction of droplet impingement and more recently for the prediction of particle flows in air- ways. However, this model includes only one-way momentum exchange coupling, and develops delta shocks and vacuum states. The main goal of this thesis is to improve this model, especially for the prevention of delta shocks and vacuum states, and the adjunction of two-way momentum exchange coupling. Using a characteristic analysis, the condition for loss of regularity of smooth solutions of the inviscid Burgers equation with a source term is established. The same condition applies to the droplet model. The Riemann problems associated, respectively, to the Burgers equation with a source term and the droplet model are solved. The characteristics are curves that tend asymptotically to straight lines. The existence of an entropic solution to the generalized Rankine-Hugoniot conditions is proven. Next, a way for preventing the formation of delta shocks and vacuum states in the model is identified and a new Eulerian droplet model is proposed. A new hierarchy of two-way coupling Eulerian models is derived. Each model is analyzed and numerical comparisons of the models are carried out. Finally, 2D computations of air-particle flows comparing the new Eulerian droplet model with the standard Eulerian droplet model are presented.

APA, Harvard, Vancouver, ISO, and other styles

23

Luo, Sai, and 罗赛. "Fabric evolution of two-dimensional idealized particle assemblage during shear." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 2012. http://hub.hku.hk/bib/B49799721.

Full text

Abstract:

Microstructure or fabric definitely affects macroscopic mechanical behavior of granular material. It is also well-observed that fabric evolves with shearing or plastic deformation. In this study, a series of two-dimensional numerical direct shear tests are carried out with the discrete element method, to study the initial fabric effect on global material responses and their micro-macroscopic relations. Idealized particle assemblages are made up of mono-size elongated particles and are prepared by a “deposition” method. Elongated particle is modeled by the built-in clump logic, in which constitutive balls are joined together without further breakage. In the deposition method, there are three controlling parameters, including, deposited direction, inter-particle friction coefficient and particle number, to prepare specimens with similar initial density but different initial packing or fabric. Three types of fabric of particle assemblages are examined quantitatively and are monitored during shearing, including, particle orientations (PO), contact normal forces (NF), and void spaces (VS). These fabric distributions are described by two parameters―anisotropic degree ( ) and orientation angle ( ), with clear physical implications. An additional parameter ( ) describing the average size of voids, is used to quantify void perimeter. It is found that this parameter has a relation with the assemblage’s volumetric response. C With the systematic and meticulous quantification method, the linkage between the macroscopic and microscopic responses of particle assemblages is discussed quantitatively. The results show that the initial packing affects the shear zone thickness, initial stiffness, peak strength, and dilation rate. In the shear zone, particle orientations do not exhibit a unique state at the final stage of direct shearing. At that state, strong normal forces and strong voids are parallel to the major principal stress direction. It seems that the initial packing does not affect their final distributions. At the end of reverse shearing, strong voids and strong normal forces in the shear zone give an essentially unique state, and their preferential directions are related to the changed loading direction. However, apparent stable particle orientations are still affected by the initial fabric.
published_or_final_version
Civil Engineering
Master
Master of Philosophy

APA, Harvard, Vancouver, ISO, and other styles

24

Musa, Zulkarnain 1964. "An accelerated conjugate direction procedure for slope stability analysis." Thesis, The University of Arizona, 1988. http://hdl.handle.net/10150/276912.

Full text

Abstract:

CSLIP2 (De Natale, 1987) is the only slope stability program that utilizes a "direction set" optimization routine in its search for the minimum safety factor. However, CSLIP2 which employs Powell's Conjugate Direction Method permits only the horizontal and vertical directions (x and y) to be used as the initial direction set. The efficiency of the existing search routine is improved by replacing the x-y coordinate directions with initial directions that are parallel to and perpendicular to the principal axis of the safety factor contours.

APA, Harvard, Vancouver, ISO, and other styles

25

Barlow, Andrew. "An adaptive multi-material Arbitrary Lagrangian Eulerian algorithm for computational shock hydrodynamics." Thesis, Swansea University, 2002. https://cronfa.swan.ac.uk/Record/cronfa43081.

Full text

APA, Harvard, Vancouver, ISO, and other styles

26

Zhu, Tulong. "Meshless methods in computational mechanics." Diss., Georgia Institute of Technology, 1998. http://hdl.handle.net/1853/11795.

Full text

APA, Harvard, Vancouver, ISO, and other styles

27

Lacy, Thomas E. Jr. "Distribution effects in damage mechanics." Diss., Georgia Institute of Technology, 1998. http://hdl.handle.net/1853/15937.

Full text

APA, Harvard, Vancouver, ISO, and other styles

28

Miller, Matthew P. "Improved constitutive laws for finite strain inelastic deformation." Diss., Georgia Institute of Technology, 1993. http://hdl.handle.net/1853/16098.

Full text

APA, Harvard, Vancouver, ISO, and other styles

29

Liu, Chi-hong, and 廖志航. "Base friction modelling of discontinuous rock masses." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 2002. http://hub.hku.hk/bib/B42577123.

Full text

APA, Harvard, Vancouver, ISO, and other styles

30

Li, Lian, and 李煉. "Microscopic study and numerical simulation of the failure process of granite." Thesis, The University of Hong Kong (Pokfulam, Hong Kong), 2001. http://hub.hku.hk/bib/B31242005.

Full text

APA, Harvard, Vancouver, ISO, and other styles

31

SOMASUNDARAM, SUJITHAN. "CONSTITUTIVE MODELLING FOR ANISOTROPIC HARDENING BEHAVIOR WITH APPLICATIONS TO COHESIONLESS SOILS (INDUCED, KINEMATIC, NON-ASSOCIATIVENESS)." Diss., The University of Arizona, 1986. http://hdl.handle.net/10150/188165.

Full text

Abstract:

A constitutive model based on rate-independent elastoplasticity concepts is developed to simulate the behavior of geologic materials under arbitrary three-dimensional stress paths, stress reversals and cyclic loading. The model accounts for the various factors such as friction, stress path, stress history, induced anisotropy and initial anisotropy that influence the behavior of geologic materials. A hierarchical approach is adapted whereby models of progressively increasing sophistication are developed from a basic isotropic-hardening associative model. The influence of the above factors is captured by modifying the basic model for anisotropic (kinematic) hardening and deviation from normality (nonassociativeness). Both anisotropic hardening and deviation from normality are incorporated by introducing into the formulation a second order tensor whose evolution is governed by the level of induced anisotropy in the material. In the stress-space this formulation may be interpreted as a translating potential surface Q that moves in a fixed field of isotropic yield surfaces. The location of the translating surface in the stress-space, at any stage of the deformation, is given by the 'induced anisotropy' tensor. A measure to represent the level of induced anisotropy in the material is defined. The validity of this representation is investigated based on a series of special stress path tests in the cubical triaxial device on samples of Leighton Buzzard sand. The significant parameters of the models are defined and determined for three sands based on results of conventional laboratory test results. The model is verified with respect to laboratory multiaxial test data under various paths of loading, unloading, reloading and cyclic loading.

APA, Harvard, Vancouver, ISO, and other styles

32

PRUETT, CHARLES DAVID. "NUMERICAL SIMULATION OF NONLINEAR WAVES IN FREE SHEAR LAYERS (MIXING, COMPUTATIONAL, FLUID DYNAMICS, HYDRODYNAMIC STABILITY, SPATIAL, FLUID FLOW MODEL)." Diss., The University of Arizona, 1986. http://hdl.handle.net/10150/183869.

Full text

Abstract:

A numerical model has been developed which simulates the three-dimensional stability and transition of a periodically forced free shear layer in an incompressible fluid. Unlike previous simulations of temporally evolving shear layers, the current simulations examine spatial stability. The spatial model accommodates features of free shear flow, observed in experiments, which in the temporal model are precluded by the assumption of streamwise periodicity; e.g., divergence of the mean flow and wave dispersion. The Navier-Stokes equations in vorticity-velocity form are integrated using a combination of numerical methods tailored to the physical problem. A spectral method is adopted in the spanwise dimension in which the flow variables, assumed to be periodic, are approximated by finite Fourier series. In complex Fourier space, the governing equations are spatially two-dimensional. Standard central finite differences are exploited in the remaining two spatial dimensions. For computational efficiency, time evolution is accomplished by a combination of implicit and explicit methods. Linear diffusion terms are advanced by an Alternating Direction Implicit/Crank-Nicolson scheme whereas the Adams-Bashforth method is applied to convection terms. Nonlinear terms are evaluated at each new time level by the pseudospectral (collocation) method. Solutions to the velocity equations, which are elliptic, are obtained iteratively by approximate factorization. The spatial model requires that inflow-outflow boundary conditions be prescribed. Inflow conditions are derived from a similarity solution for the mean inflow profile onto which periodic forcing is superimposed. Forcing functions are derived from inviscid linear stability theory. A numerical test case is selected which closely parallels a well-known physical experiment. Many of the aspects of forced shear layer behavior observed in the physical experiment are captured by the spatial simulation. These include initial linear growth of the fundamental, vorticity roll-up, fundamental saturation, eventual domination of the subharmonic, vortex pairing, emergence of streamwise vorticity, and temporary stabilization of the secondary instability. Moreover, the spatial simulation predicts the experimentally observed superlinear growth of harmonics at rates 1.5 times that of the fundamental. Superlinear growth rates suggest nonlinear resonances between fundamental and harmonic modes which are not captured by temporal simulations.

APA, Harvard, Vancouver, ISO, and other styles

33

YU, CHUNG-CHYI. "FINITE-ELEMENT ANALYSIS OF TIME-DEPENDENT CONVECTION DIFFUSION EQUATIONS (PETROV-GALERKIN)." Diss., The University of Arizona, 1986. http://hdl.handle.net/10150/183930.

Full text

Abstract:

Petrov-Galerkin finite element methods based on time-space elements are developed for the time-dependent multi-dimensional linear convection-diffusion equation. The methods introduce two parameters in conjunction with perturbed weighting functions. These parameters are determined locally using truncation error analysis techniques. In the one-dimensional case, the new algorithms are thoroughly analyzed for convergence and stability properties. Numerical schemes that are second order in time, third order in space and stable when the Courant number is less than or equal to one are produced. Extensions of the algorithm to nonlinear Navier-Stokes equations are investigated. In this case, it is found more efficient to use a Petrov-Galerkin method based on a one parameter perturbation and a semi-discrete Petrov-Galerkin formulation with a generalized Newmark algorithm in time. The algorithm is applied to the two-dimensional simulation of natural convection in a horizontal circular cylinder when the Boussinesq approximation is valid. New results are obtained for this problem which show the development of three flow regimes as the Rayleigh number increases. Detailed calculations for the fluid flow and heat transfer in the cylinder for the different regimes as the Rayleigh number increases are presented.

APA, Harvard, Vancouver, ISO, and other styles

34

Foster, David H. "Fabry-Perot and Whispering Gallery Modes In Realistic Resonator Models." Thesis, view abstract or download file of text, 2006. http://wwwlib.umi.com/cr/uoregon/fullcit?p3211216.

Full text

Abstract:

Thesis (Ph. D.)--University of Oregon, 2006.
Typescript. Includes vita and abstract. Includes bibliographical references (leaves 204-213). Also available for download via the World Wide Web; free to University of Oregon users.

APA, Harvard, Vancouver, ISO, and other styles

35

LIANG, SHEN-MIN. "REFINED NUMERICAL SOLUTIONS OF THE TRANSONIC FLOW PAST A WEDGE (OBLIQUE SHOCK)." Diss., The University of Arizona, 1985. http://hdl.handle.net/10150/187911.

Full text

Abstract:

An adaptive refinement procedure combining the ideas of solving a modified difference equation and of adaptive mesh refinement is introduced. The numerical solution on a fixed grid is improved by inclusion of approximated truncation error computed from local subgrid refinement. Following this procedure, a reliable scheme has been developed for refined computations of the flow past a wedge at transonic speeds. Effects of the truncation error on the pressure, wave drag, sonic line, and shock position are investigated. By comparing the pressure drag on the wedge and the wave drag due to the shocks, the existence of a supersonic-to-supersonic shock originating from the wedge shoulder is confirmed.

APA, Harvard, Vancouver, ISO, and other styles

36

Vohra, Sanjay. "A mechanics framework for modeling fiber deformation on draw rollers and freespans." Diss., Available online, Georgia Institute of Technology, 2006, 2006. http://etd.gatech.edu/theses/available/etd-05172006-141347/.

Full text

Abstract:

Thesis (Ph. D.)--Polymer, Textile & Fiber Engineering, Georgia Institute of Technology, 2007.
Karl I. Jacob, Committee Chair ; Youjiang Wang, Committee Member ; Mary Lynn Realff, Committee Member ; Arun Gokhale, Committee Member ; Rami Haj-Ali, Committee Member.

APA, Harvard, Vancouver, ISO, and other styles

37

Ellis, William Joseph. "Application of statistical mechanics to a model neuron /." Title page, contents and abstract only, 1993. http://web4.library.adelaide.edu.au/theses/09PH/09phe479.pdf.

Full text

APA, Harvard, Vancouver, ISO, and other styles

38

McTaggart, Kevin Andrew. "Hydrodynamics and risk analysis of iceberg impacts with offshore structures." Thesis, University of British Columbia, 1989. http://hdl.handle.net/2429/30733.

Full text

Abstract:

The evaluation of design iceberg impact loads for offshore structures and the influence of hydrodynamic effects on impact loads are examined. Important hydrodynamic effects include iceberg added mass, wave-induced oscillatory iceberg motions, and the influence of a large structure on the surrounding flow field and subsequent velocities of approaching icebergs. The significance of these phenomena has been investigated using a two-body numerical diffraction model and through a series of experiments modelling the drift of various sized icebergs driven by waves and currents approaching a large offshore structure. Relevant findings from the hydrodynamic studies have been incorporated into two probabilistic models which can be used to determine design iceberg collision events with a structure based on either iceberg kinetic energy upon impact or global sliding force acting on the structure. Load exceedence probabilities from the kinetic energy and sliding force models are evaluated using the second-order reliability method. Output from the probabilistic models can be used to determine design collision parameters and to assess whether more sophisticated modelling of various impact processes is required. The influence of the structure on velocities of approaching icebergs is shown to be significant when the structure horizontal dimension is greater than twice the iceberg dimension. As expected, wave-induced oscillatory motions dominate the collision velocity for smaller icebergs but have a negligible effect on velocity for larger icebergs.
Applied Science, Faculty of
Civil Engineering, Department of
Graduate

APA, Harvard, Vancouver, ISO, and other styles

39

Ma, Zhiwen. "A combined differential and integral model for high temperature fuel cells." Diss., Georgia Institute of Technology, 2000. http://hdl.handle.net/1853/15831.

Full text

APA, Harvard, Vancouver, ISO, and other styles

40

Fiechter, Jerome. "Numerical study of platelet transport in flowing blood." Thesis, Georgia Institute of Technology, 1998. http://hdl.handle.net/1853/16770.

Full text

APA, Harvard, Vancouver, ISO, and other styles

41

Fischer, Christian E. "Forging process models for use with global optimization of manufacturing prcesses." Ohio : Ohio University, 1999. http://www.ohiolink.edu/etd/view.cgi?ohiou1175269765.

Full text

APA, Harvard, Vancouver, ISO, and other styles

42

Welch, Charles Robert. "A full-engulfment engineering model, and its experimental and numerical verification, for the response of a rigid body to ground-shock." Diss., This resource online, 1993. http://scholar.lib.vt.edu/theses/available/etd-09192008-063134/.

Full text

APA, Harvard, Vancouver, ISO, and other styles

43

Chin, Victor B. L. "The dynamic response of pile-soil interfaces during pile driving and dynamic testing events." Monash University, Dept. of Civil Engineering, 2003. http://arrow.monash.edu.au/hdl/1959.1/9421.

Full text

APA, Harvard, Vancouver, ISO, and other styles

44

Que, Norbert S. Civil &amp Environmental Engineering Faculty of Engineering UNSW. "Identification of cohesive crack fracture parameters using mathematical programming." Awarded by:University of New South Wales. School of Civil and Environmental Engineering, 2003. http://handle.unsw.edu.au/1959.4/19189.

Full text

Abstract:

This thesis is concerned with the characterisation of the parameters governing the tension-softening relations of the cohesive crack model. Parameter identification is an important area in fracture mechanics as it enables the use of a fracture model for the simulation of fracture processes in structures. Research, however, has shown that such a task is not trivial and continues to pose challenging problems to experimentalists and analysts alike. This dissertation presents general and efficient indirect methods for the characterisation of mode I fracture parameters defining the cohesive crack model. The identification problem is formulated as a special type of inverse problem. The formulation is in the form of a constrained optimisation problem known as a mathematical program with equilibrium constraints characterised, in the present instance, by complementarity conditions involving the orthogonality of two-sign constrained vectors. The solution of such a mathematical program is computationally challenging as it is disjunctive and nonconvex by nature. A number of nonlinear programming based approaches are proposed, after appropriate reformulation of the mathematical program as an equivalent nonlinear programming problem. Actual experimental data are used to validate and determine the most suitable algorithm for parameter identification. It was found that the smoothing-based method is by far superior than other schemes. As the problem is nonconvex and the nonlinear program can only guarantee a local or stationary point, global optimisation procedures are introduced in order to verify the accuracy of the solutions obtained by the algorithm. Two evolutionary search methods capable of finding the global optimum are implemented for parameter identification. The results generated by the evolutionary search techniques confirm the reliability of the solutions identified by the best nonlinear programming algorithm. All computations carried out in the thesis suggest the suitability and robustness of the selected algorithm for parameter identification.

APA, Harvard, Vancouver, ISO, and other styles

45

Watson, Cody. "Modeling of pressure transients in fuel injection lines." Thesis, Georgia Institute of Technology, 1999. http://hdl.handle.net/1853/16869.

Full text

APA, Harvard, Vancouver, ISO, and other styles

46

James, Ashley Jean. "Vibration induced droplet ejection." Diss., Georgia Institute of Technology, 2000. http://hdl.handle.net/1853/17337.

Full text

APA, Harvard, Vancouver, ISO, and other styles

47

Wilson, Amanda C. "Equivalent initial flaw size model development for turbine blades using in-service data." Thesis, Georgia Institute of Technology, 2003. http://hdl.handle.net/1853/20006.

Full text

APA, Harvard, Vancouver, ISO, and other styles

48

Ho, Yeu Chuan. "Stability and elastohydrodynamic behavior of rotary lip seals." Diss., The University of Arizona, 1991. http://hdl.handle.net/10150/185433.

Full text

Abstract:

Mathematical models for rotary lip seals is developed to study the basic stability and dynamic response of the lip seals. In this thesis, a linear stability analysis is performed to find the stability characteristics of such a mechanical system. Then, a finite element algorithm for the numerical integration of the system of coupled differential equations governing the dynamic behavior of the lip seals is presented.

APA, Harvard, Vancouver, ISO, and other styles

49

Zhang, Yi. "Numerical modeling of shock wave propagation and contaminant fate and transport in open channel networks." Diss., Georgia Institute of Technology, 1998. http://hdl.handle.net/1853/20159.

Full text

APA, Harvard, Vancouver, ISO, and other styles

50

Amany, Aya Nicole Marie. "Characterization of shear and bending stiffness for optimizing shape and material of lightweight beams." Thesis, McGill University, 2007. http://digitool.Library.McGill.CA:80/R/?func=dbin-jump-full&object_id=112553.

Full text

Abstract:

Optimized slender and short-thick beams are used in building, aircraft and machine structures to increase performance at a lower material cost. A previous work proposes an optimum shape, material and size selection model to design lightweight slender beams under pure bending. In short-thick beams, the transverse shear effects are no longer negligible and impact the choice of the optimum shape. This work extends such an optimum selection model to consider both slender and short-thick beams, by formulating the total beam stiffness design requirement as a combination of shear and bending stiffness. Selection charts are developed to show the impact of design variables, such as shape, size, material and slenderness, on the total beam stiffness. The model of total beam stiffness is validated against computational results from finite element analyses of beam models. A case study demonstrates the use of the selection charts to compare the performance of beams at the conceptual design stage.

APA, Harvard, Vancouver, ISO, and other styles

Dissertations / Theses on the topic 'Shock (Mechanics) – Mathematical models'

Create a spot-on reference in APA, MLA, Chicago, Harvard, and other styles