Relevant bibliographies by topics / Piezokeramické materiály

Contents

  1. Journal articles
  2. Dissertations / Theses

Academic literature on the topic 'Piezokeramické materiály'

Author: Grafiati
Published: 28 June 2021
Last updated: 4 February 2022

Create a spot-on reference in APA, MLA, Chicago, Harvard, and other styles

Select a source type:

Consult the lists of relevant articles, books, theses, conference reports, and other scholarly sources on the topic 'Piezokeramické materiály.'

Next to every source in the list of references, there is an 'Add to bibliography' button. Press on it, and we will generate automatically the bibliographic reference to the chosen work in the citation style you need: APA, MLA, Harvard, Chicago, Vancouver, etc.

You can also download the full text of the academic publication as pdf and read online its abstract whenever available in the metadata.

Journal articles on the topic "Piezokeramické materiály"

1

Pohl, Jürgen. "CFK-Piezokeramik-Verbunde zerstörungsfrei charakterisieren." Materials Testing 46, no. 10 (October 2004): 517–23. http://dx.doi.org/10.3139/120.100621.

Full text
APA, Harvard, Vancouver, ISO, and other styles
2

Wäsche, R. "Piezokeramik. VonKarl Ruschmeyer und 7 Coautoren, 211 Seiten, zahlreiche Tabellen und Abbildungen, expert verlag Renningen 1994, Reihe Kontakt und Studium, Band 460, DM 69,-, ISBN 3-8169-1152-8." Materials and Corrosion/Werkstoffe und Korrosion 46, no. 3 (March 1995): 182. http://dx.doi.org/10.1002/maco.19950460310.

Full text
APA, Harvard, Vancouver, ISO, and other styles

Dissertations / Theses on the topic "Piezokeramické materiály"

1

Zeman, Dominik. "Mechanické vlastnosti dopovaných piezokeramických materiálů na bázi BaTiO3." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2021. http://www.nusl.cz/ntk/nusl-442597.

Full text
Abstract:
This master‘s thesis deals with study of basic physical, microstructural and mechanical properties of doped piezoceramic materials based on BaTiO3 prepared by electrophoretic deposition. The dopants used were rare earth oxides, i.e. Eu2O3, Er2O3, CeO2, Dy2O3 and Tb4O7 in amounts 1, 3 and 5 wt. %. The influence of dopants and their amount on density, phase composition, mean grain size, hardness, elastic modulus, fracture toughness, and flexural strength was examined. Suitable dopant choice enabled decrease in mean grain size and increase in relative density, hardness, elastic modulus, fracture toughness and flexural strength of sintered specimens. Relative densities up to 99 %, mean grain size below 1 m, hardness up to 13,1 GPa, elastic modulus up to 199 GPa, fracture toughness above 1 MPa·m1/2 and flexural strength above 115 MPa were achieved.
APA, Harvard, Vancouver, ISO, and other styles
2

Dostal, Vojtěch. "Návrh topologie kompozitního piezokeramického snímače." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2020. http://www.nusl.cz/ntk/nusl-418189.

Full text
Abstract:
This master thesis deals with design and numerical modelling of piezoceramic sensor, which is placed on a rail, in order to generate electrical energy, which can be used for wireless monitoring of railway traffic and to monitor the condition of the railway. The thesis is divided into three parts. Theoretically background of piezoelectric energy harvesting is described in first part, where some previous application of piezoelectric generator in railway area are shown. In the second part, parametric analysis of numerical model is performed, which directly leads to finding best location on a rail, where piezoelectric generator should be placed. For this analysis the homogenized model of MFC sensor was used. Results of the numerical model were then compared with the results of the conducted experiment. The third part presented own design of piezoceramic sensor, which is placed onto most suitable location on a rail. Results from numerical analysis shown eligibility of using piezoceramic sensor to monitor the railway traffic.
APA, Harvard, Vancouver, ISO, and other styles
3

Brockmann, Tobias H. "Theory of adaptive fiber composites from piezoelectric material behavior to dynamics of rotating structures." Dordrecht Heidelberg London New York, NY Springer, 2009. http://d-nb.info/997517948/34.

Full text
APA, Harvard, Vancouver, ISO, and other styles
4

Mařák, Vojtěch. "Příprava a vlastnosti dopovaných piezokeramických materiálů na bázi BaTiO3." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2020. http://www.nusl.cz/ntk/nusl-417065.

Full text
Abstract:
This diploma thesis deals with the preparation of doped piezoceramic materials based on BaTiO3 using electrophoretic deposition. Five rare earth oxides, i.e. Er2O3, Dy2O3, Eu2O3, Tb407 and CeO2, were used as dopants in amounts of 1, 3, and 5 wt. %. The prepared deposits were evaluated in terms of preparation methodology, high temperature dilatometry, X-ray diffraction analysis, relative density, mean grain size, hardness and fractographic analysis. The study of dilatometric curves described the sintering behavior and its changes at different material compositions. X-ray diffraction analysis revealed a tetragonal phase in all samples; the tetragonality of the BaTiO3 crystalline cell decreased with dopant content. By a suitable choice of dopant, it was possible to significantly increase the relative density of sintered samples, their hardness and at the same time prevent the samples from coarsening of the microstructure during heat treatment. A relative density up to 98 %, a mean grain size below 1 m and a hardness of over 10 GPa were achieved. Analysis of the fracture surfaces revealed that the fracture mode was transcrystalline for the most of studied materials; only the samples doped with cerium dioxide had fracture surfaces with both transcrystalline and intercrystalline fracture modes. Based on the obtained results, a suitable composition of the material for the intended use in a layered piezoceramic harvester was identified, which, in addition to the BaTiO3 layers, consists of functionally-protective Al2O3 and ZrO2 layers.
APA, Harvard, Vancouver, ISO, and other styles
5

Fojtík, Ondřej. "Příprava a optimalizace piezoelektrických materiálů na bázi BCZT pro energy harvesting." Master's thesis, Vysoké učení technické v Brně. Fakulta chemická, 2019. http://www.nusl.cz/ntk/nusl-401844.

Full text
Abstract:
This thesis deals with fabrication and optimization of lead-free piezoceramics based on (Ba0,85Ca0,15Zr0,1Ti0,9)O3 (BCZT). The BCZT precursor powder was synthesized by sol-gel method. Dependence of relative density, microstructure, phase structure and piezoelectric properties on the sintering temperature in a range from 1300–1500 °C was studied on disc shaped samples, which were prepared by cold isostatic pressing (CIP) using pressure of 700 MPa. It was found, that sintering at 1300 and 1350 °C leads to ceramics with fine-grain microstructure, which exhibits poor piezoelectric properties (d*33 = 50 pC·N1 and 65 pC·N1, respectively). The highest value of piezoelectric charge coefficient was obtained by sintering at 1500 °C (d*33 = 390 pC·N1). Furthermore, BCZT thick films were prepared by tape casting. The composition of the ceramic slurry was optimized and various sintering techniques were tested to obtain completely flat films of BCZT ceramics. The correct sintering configuration has not been found. The least deformation of the films was achieved when the samples were sintered hung on the ZrO2 rod. The highest value of d*33 for BCZT films was measured when the sample was sintered at 1400 °C with the dwell time for 4 h (d*33 = 340 pC·N1).
APA, Harvard, Vancouver, ISO, and other styles
6

Hanus, Jiří. "Využití piezo-materiálu pro získávání elektrické energie z vibrací." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2009. http://www.nusl.cz/ntk/nusl-228611.

Full text
Abstract:
Master’s Thesis deals with obtaining electricity from the vibrations of the surrounding environment through piezoelectric vibration generator. To simulation piezoceramics and design mechanical parts of the generator was used simulation program ANSYS 10.0. First, parameters of the designed piezoelectric generator were numerically calculated, and then these values were compared with the real sample. Further work is in the description of material properties of piezo materials.
APA, Harvard, Vancouver, ISO, and other styles
7

Karkuszová, Karina. "Příprava keramických materiálů pro piezoelektrické aplikace." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2020. http://www.nusl.cz/ntk/nusl-417056.

Full text
Abstract:
The content of this thesis is about preparation and processing of lead-free piezoceramic materials with perovskite structure. Potassium sodium niobate (KNN) powder was prepared by solid state reaction (SSR) and liquid phase reaction (sol-gel reaction). The powders were formed by uniaxial and isostatic pressing and further sintered. The density, grain size and morphology were determined on the sintered samples. The powder, synthesised by SSR and sintered in a conventional furnace, was chosen as a standard. The maximum density achieved on samples after optimization of sintering cycle was 93 %TD. The sintering optimization involved a homogenization step at 950 °C, which promotes the correct development of the phase composition and microstructure, followed by sintering at 1120 °C. The same approach and sintering cycle were used for sintering the samples, prepared by sol-gel synthesis. The maximum density of the samples prepared by sol-gel reaction and sintered in a conventional way, was 92 %TD. For further comparison, both of the synthesised powders were sintered using SPS (spark plasma sintering), which increased their final density up to 97 %TD. The approximate value of the piezoelectric coefficient d33 (pC/N) has been measured on selected SSR samples with pure phase composition ((K0,5Na0,5)NbO3). The best measured value of d33 was around 100 pC/N.
APA, Harvard, Vancouver, ISO, and other styles
8

Pavelec, Jiří. "Vývoj lineárního posuvu pro UHV STM/AFM." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2011. http://www.nusl.cz/ntk/nusl-229812.

Full text
Abstract:
The aim of this diploma thesis is to develop a linear positioning stage for Ultra High Vacuum (UHV) environment. Simple prototypes of the linear positioning stage were designed and incorporated as part of a multiaxis sample manipulator for a UHV Scanning Tunneling Microscopy / Atomic Force Microscopy (STM/AFM). Different types of position encoders and linear guideways are discussed. Implementation of the homodyne interferometer as an optimization tool for a slip-stick based linear stage is described. Scalar diffraction theory is used to model the diffraction grating optical position encoder behavior.
APA, Harvard, Vancouver, ISO, and other styles
We offer discounts on all premium plans for authors whose works are included in thematic literature selections. Contact us to get a unique promo code!

To the bibliography