Journal articles: 'Manufacture and works'

1

Voznyak, Orest, Khrystyna Myroniuk, Iryna Sukholova, Oleksandr Dovbush, and Mariana Kasynets. "Increase of ventilation systems procurement and installation works efficiency." Theory and Building Practice 2020, no. 2 (November 20, 2020): 77–83. http://dx.doi.org/10.23939/jtbp2020.02.077.

Full text

Abstract:

The article presents the results of theoretical research on obtaining of the maximum profit by the installation and procurement company in the manufacture and sale of pipe billets for the installation of ventilation systems in the production premise. Graphical and analytical dependences are given. The results of research substantiate the receipt of the maximum profit in the manufacture and sale of the ventilation pipe billets of the different diameters by the installation and procurement enterprise. The purpose of the work is to increase the efficiency of ventilation system installationin production facilities, to determine the maximum profit for the installation and procurement company in the manufacture and sale of pipe billets of the different diameters of ventilation system in the presence of several restrictions on materials and manpower, identify ways to improve installation of ventilation system in production facilities of small volume and justification of the calculation method. Quantitative characteristics of the objective function under given initial conditions are established. The calculated dependences for determining the parameters of the objective function are obtained. The obtained results allow to determine the optimal parameters of the values at the given restrictions on materials and labor intensity of production. The maximum profit in the manufacture and sale of ventilation pipe billets of different diameters by the procurement and installation company is determined. Using of the graphical method and the simplex method to determine the required parameters can significantly increase the efficiency criteria for procurement and installation work and thus reduce the amount of labor and material consumption for the manufacture and installation of ventilation systems.

APA, Harvard, Vancouver, ISO, and other styles

2

Cherepanov, Anatoliy. "OF FORECASTING THE RESOURCE OF SINGLE AND UNIQUE MACHINES." Bulletin of the Angarsk State Technical University 1, no. 16 (December 27, 2022): 153–64. http://dx.doi.org/10.36629/2686-777x-2022-1-16-153-164.

Full text

Abstract:

The article presents an analysis of methods for predicting the resource of individual and unique machines based on scientific works, inventions, and regulatory documents since 1988. The analysis touched upon the works devoted to forecasting the design, initial, determined during manufacture, and residual resources. The advantages and disadvantages of methods for estimating the resource of single and unique machines are considered. The analysis showed that in most works and methodological recommendations, methods of forecasting the residual resource are mainly given. As is known, safety begins at the stage of project development, therefore, it is necessary to evaluate not only the residual resource, as is customary in most scientific developments, but also to more accurately determine the initial resource during manufacture and the current resource during operation. In earlier works, only the reliability of hazardous facilities was considered, and only in the last decade has the development of methods for evaluating the design and initial resource in the manufacture of single and unique machines begun. The ways of development of methods for assessing the resource of individual and unique machines in their manufacture in accordance with the requirements of standards and technical documentation are shown

APA, Harvard, Vancouver, ISO, and other styles

3

Dang, Phuong Xuan. "Design and manufacture of cycloid reduction gearbox made by combined materials for working in corrosive environment." Science and Technology Development Journal 20, K5 (August 31, 2017): 81–86. http://dx.doi.org/10.32508/stdj.v20ik5.1163.

Full text

Abstract:

This paper presents research result of design and manufacture of the cycloidal gearbox with some advantages such as low noise, high transmission ratio, high load, and erosive resistance. The new point of this works is the utilization of combined stainless materials that can be worked in an erosive environment, especially in the aquatic mechanical area, in order to save material and to increase the cycle life of this equipment. Besides, the cycloidal gearbox with stainless steel and polymer materials can be lubricated by water and is used with water-resistant or submersible electric motor. This new cycloidal gearbox can replacethe worm gearbox. A 1,5 HP cycloidal gearbox with the reduction ratio 29 that is used in aquaculture has been designed and manufactured successfully. In this work, the analytical method and numerical simulation are used to design and manufacture the gearbox. For the future works, this cycloidal gearbox will be tested in the real environment with aquaculture aerator system so that its performance will be fully verified and assessed

APA, Harvard, Vancouver, ISO, and other styles

4

Kim, Dong-jo. "Manufacture of LED Display Works based on Real time Interaction." Journal of Digital Art Engineering and Multimedia 4, no. 1 (June 30, 2017): 41–49. http://dx.doi.org/10.29056/idaem.2017.06.04.

Full text

APA, Harvard, Vancouver, ISO, and other styles

5

Fithriyah, Zulfita, and Nazaruddin Malik. "PENGARUH KREDIT PERBANKAN TERHADAP PERTUMBUHAN INDUSTRI MANUFAKTUR DALAM MENUNJANG PERTUMBUHAN EKONOMI INDONESIA." Jurnal Ekonomi Pembangunan 8, no. 1 (October 6, 2016): 210. http://dx.doi.org/10.22219/jep.v8i1.3596.

Full text

Abstract:

This research works through about influence between banking credit insuranceansies with industrial growth of manufacture. Besides also studies about vesting influence of credit insuranceansi to economic growth in Indonesia. Based on research done, obtained result that level of credit insuranceansi given to manufacture industry will affect at improvement of output at company. So equally, the many vestings of credit insuranceansi compares linear with industrial improvement of manufacture. At research hereinafter, happened the relation of concurrent between industrial growths of manufacture with chartered investment counsel growth. Where when industrial growth of manufacture increased hence will cause improvement at chartered investment counsel growth. Manufacture industry is one of economic sector, which if manufacture industry increased hence its the contribution is ever greater to chartered investment counsel growth. So growth of chartered investment counsel can increase

APA, Harvard, Vancouver, ISO, and other styles

6

Peña, F., C. Fernández, G. Valiño, B. J. Álvarez, J. C. Rico, and S. Mateos. "Design and construction of a test bench for the manufacture and on-machine non-contact inspection of parts obtained by Fused Filament Fabrication." IOP Conference Series: Materials Science and Engineering 1193, no. 1 (October 1, 2021): 012090. http://dx.doi.org/10.1088/1757-899x/1193/1/012090.

Full text

Abstract:

Abstract Industrial application of additive manufacturing (AM) technologies is subjected to limitations related to the lack of dimensional and geometrical accuracy of manufactured parts. Many works were dedicated to improve quality of parts manufactured by AM, but integrated solutions in commercial-type AM machines have not been achieved yet. With this aim, the present work describes the design, manufacture and starting-up of a mechatronic test bench first prototype, with the double capability of 3D printing by Fused Filament Fabrication (FFF) and non-contact inspection of deposited layers. Both systems operate coordinately as the part is constructed. Final tests describe the effectiveness of both integrated systems and state the basis for further research.

APA, Harvard, Vancouver, ISO, and other styles

7

Bigeev, V. A., S. K. Nosov, and B. A. Sarychev. "Development of the manufacture of armor steel in the Magnitogorsk metallurgical works." Russian Metallurgy (Metally) 2014, no. 6 (June 2014): 471–73. http://dx.doi.org/10.1134/s0036029514060044.

Full text

APA, Harvard, Vancouver, ISO, and other styles

8

Zhao, Shuai, De Qiang Zhang, and Nu Hu. "The Research on Rapid Design and Manufacture Method for Letters Product Based on RP Technology." Applied Mechanics and Materials 496-500 (January 2014): 2594–97. http://dx.doi.org/10.4028/www.scientific.net/amm.496-500.2594.

Full text

Abstract:

In order to solve the problem that the design and manufacture method for letters product in traditional ways has a long period and high cost, a new design and manufacture method based on RP technology was proposed. Firstly, Rhinoceros software was used to design the initial model, and then the initial model was put into SolidWorks software for model processing. After that, the established model was put into RPdata software for data processing. Finally, by using RP450B rapid prototyping machine, a rapid prototype of the model was achieved. Through the study, some key problems such as model design, processing of model data and manufacturing process were discussed. The new design and manufacture method has greatly shortened the design and manufacture cycle of the letters product, and it provides the reference for the design and manufacture for other art works.

APA, Harvard, Vancouver, ISO, and other styles

9

Syavira, Riri, Tiaminah Nasution, Raisa Nabila, and Rita Juliani. "DESIGN AND BUILD SALAK (Salacca Sumatrana) EMBALMING MACHINE WITH CONVEYOR." Jurnal Geliga Sains: Jurnal Pendidikan Fisika 6, no. 1 (August 13, 2018): 60. http://dx.doi.org/10.31258/jgs.6.1.60-64.

Full text

Abstract:

It has been done the manufacture of Salak embalming machine for partners of Lopo Salak inPadangsidempuan. This machine can be used to assist partners in the process of embalming Salak to produce good quality and guaranteed freshness. The steps in the manufacture of this machine start from the design, the provision of tools and materials, manufacture and test the machine. The results show that the machine works optimally with the average production of salak 25 kg/hour due to embalming. In addition, the embalming machine has a propulsion engine that serves as the embalming and drying of Salak.

APA, Harvard, Vancouver, ISO, and other styles

10

Černý, Ivo. "Evaluation of Interlaminar Shear Strength of Longitudinal GRP Railway Bogie Frames Considering Microstructure Aspects." Key Engineering Materials 577-578 (September 2013): 521–24. http://dx.doi.org/10.4028/www.scientific.net/kem.577-578.521.

Full text

Abstract:

The paper contains results of a comprehensive research and development programme aimed at an evaluation of static strength of a GRP railway bogie of a new advanced design. The works were carried out as one of the essential phases of the implementation of a EUREKA project EUROBOGIE, which is aimed at development of advanced vehicle bogies and has a great potential to lead to more efficient movement of freight and passengers with lower environmental impact. The GRP bogie design consists of three main load carrying parts, namely two quite massive longitudinal side frames connected by a central transom plate which are manufactured in a single moulding operation using the resin transfer moulding (RTM) method. Since the component is unusually thick, all parameters of the RTM method have to be well balanced. One of the critical issues in the design and manufacture is the connection area of the transom with the side frames. Therefore, testing of this subcomponent was an important part of the bogie development. Results of the experimental programme provided necessary feedback for the optimization of the manufacture technology.

APA, Harvard, Vancouver, ISO, and other styles

11

Kukharenko, M. A., and I. N. Radkova. "DEVICE FOR IMPROVING THE PLASTIC PROPERTIES OF THE WIRE RML." Litiyo i Metallurgiya (FOUNDRY PRODUCTION AND METALLURGY), no. 2 (July 7, 2018): 73–74. http://dx.doi.org/10.21122/1683-6065-2018-2-73-74.

Full text

Abstract:

Currently, various manufacturers in the manufacture of wire RML used planish-straightening device (PSD), to obtain stable mechanical and plastic properties of the wire. The ensuring of the necessary parameters of mechanical and plastic properties of the RML wire is actual for OJSC «BSW» – Belarusian Metallurgical Works – Management Company of the Holding «BMC». That is why its own design of PSD was developed at BSW. The new planish-straightening device allowed to solve several problems simultaneously: to increase the plastic characteristics of the wire, to improve the adjustment of the coil lifting and to stabilize the diameter of the wire ring PML when working on the mills.

APA, Harvard, Vancouver, ISO, and other styles

12

Shirokozhukhova, Anna, Sergey Kovalev, and Alexandr Ryazantsev. "Manufacturing Technology of Multilayer Metal Filters." E3S Web of Conferences 398 (2023): 01043. http://dx.doi.org/10.1051/e3sconf/202339801043.

Full text

Abstract:

The article presents methods for obtaining micro-holes in the manufacture of fine metal filter elements. The analysis of the results of experimental studies of filter samples with holes made by electron beam and electroerosion perforation methods is carried out. The advantages of using multilayer structures in the manufacture of filters are substantiated. The research works carried out contribute to improving the manufacturability of products of new generations of technology, which is important for mechanical engineering.

APA, Harvard, Vancouver, ISO, and other styles

13

Griffiths, B. "Manufacture Corporate Chef Works with High School Students to Create Recipes for Schools." Journal of the Academy of Nutrition and Dietetics 112, no. 9 (September 2012): A59. http://dx.doi.org/10.1016/j.jand.2012.06.216.

Full text

APA, Harvard, Vancouver, ISO, and other styles

14

Alcantara, Rosmery Aylin Tineo, Carlos Javier Canchuricra Blanca, Kebin Luis Díaz Rivera, and Eduardo Manuel Yarango Serrano. "Review of sustainable concrete based on photocatalytic to reduce the environmental impact in large works in Peru." Journal of Project Management 8, no. 2 (2023): 91–98. http://dx.doi.org/10.5267/j.jpm.2022.12.002.

Full text

Abstract:

This bibliographical review allows us to know clearly and concisely the use and effectiveness of photocatalytic concrete applied to tracks or roads, and in buildings. This study analyzes sustainable concrete based on photocatalytic to reduce the environmental impact in large-scale works through the application for the collection and review of articles published in the scientific base of Scopus using the VOSviewer software tool that analyzes a large amount of data from a group of investigations, this research is carried out from the publications of the year 2000 to the year 2022. Graphs were obtained from the database analysis with the words “Concrete”, “Photocatalytic”, “Environmental” and “Work” with the highest interest in all analysis groups. The results obtained allow us to understand the innovation of concrete based on photocatalytic in order to reduce air pollution since this need is current throughout the world, more so in globalized and rapidly growing countries, the analysis in Peru is not found no research related to the subject and there are no large-scale works related to reducing air pollution, but there are proposals to improve air quality in Lima, the capital of Peru, however this contribution is minimal to be able to positively impact the air . The manufacturing process and the materials to implement for the manufacture of concrete based on the photocatalytic were also analyzed, visualizing the advantages and disadvantages of this concrete based on the photocatalytic, adding other additional components to improve the durability of the concrete application and being viable. to apply to large-scale works. This research has the purpose of presenting a general view of the application, manufacture, advantages and disadvantages of concrete based on photocatalytic, it is important to develop and apply it in large-scale works subsidized by the Peruvian state, since these can generate a positive impact on society and the environment.

APA, Harvard, Vancouver, ISO, and other styles

15

Zhang, Ke, Ju Ping Ren, Hua Guo, Yu Hou Wu, and Kai Jun Zhao. "Crossbeam Analysis and Structure Optimization of Special-Shaped Stone Combined Machining Center." Advanced Materials Research 102-104 (March 2010): 620–24. http://dx.doi.org/10.4028/www.scientific.net/amr.102-104.620.

Full text

Abstract:

With the increase of the quantity demanded, stone products with high quality, really artsy and diversification become more and more best-selling. The special-shaped stone machining equipments with numerical control, single machine intelligent, high speed, high efficiency and multi-function combination must be manufactured to produce these stone products. In this paper, 3D design and project optimization for special-shaped stone composite machining center are carried by Solid Works and innovative design. Model analysis of the crossbeam in this machining center is carried by ANSYS and the maximum deformation value in the crossbeam is found. The crossbeam structure is optimized by comparison and analysis. The design and manufacture of special-shaped stone combined machining center is very helpful for development of manufacturing.

APA, Harvard, Vancouver, ISO, and other styles

16

Chao, Jie, and Hang Gong. "FSAE Racing Gear Selection and Shifting Agencies Choose to Discuss the Impact of Car Drivers." Applied Mechanics and Materials 721 (December 2014): 187–90. http://dx.doi.org/10.4028/www.scientific.net/amm.721.187.

Full text

Abstract:

FSC is a Formula One car contest car works by the universities or auto-related professional school students team up to participate in the design and manufacture of automotive competition. All participating teams in accordance with the rules and race car manufacturing standards, in a year's time to design and manufacture an accelerating, braking, handling, and so has excellent performance of small single-seater racing leisure, to successfully complete all or Part of the event part of the game. This article discusses the transmission of choice for car drivers.

APA, Harvard, Vancouver, ISO, and other styles

17

Chao, Yan Pu. "3D Printing Manufacture Micro-Channel Structure by Metal Micro Droplet-on-Demand Deposition." Advanced Materials Research 940 (June 2014): 311–15. http://dx.doi.org/10.4028/www.scientific.net/amr.940.311.

Full text

Abstract:

In order to realize the rapid-flexible manufacture of metal micro-channel radiator structure,metal micro-droplet deposition manufacture was proposed and an experimental setup was developed. The principle of pneumatic droplet-on-demand generator and the process of single droplet ejected from the nozzle were analyzed. The calculation model of forming wall thickness was established. On this basis, a micro-channel radiator structure was fabricated. The above research show that the manufacturing of micro-channel structure by micro-droplet deposition is feasible. This works offer a new manufacturing method for micro-channel radiator structure.

APA, Harvard, Vancouver, ISO, and other styles

18

Yang, Min, and Xing Hai Zhang. "Development and Manufacture on the New Yoga Exercising Device." Applied Mechanics and Materials 509 (February 2014): 101–4. http://dx.doi.org/10.4028/www.scientific.net/amm.509.101.

Full text

Abstract:

A new type of yoga exercising device that can release the negative oxygen ions was developed in this works to assist the training or exercising of yoga. The basic structures, working principles, machining technologies, technical requirements, operating methods and application ways were discussed in this paper. With the help of the new yoga exercising device, the trainees can master the essential skills quickly and effectively and the coach can be liberated from the heavy work of repetitive training exercise. The training and exercising environments can be largely improved and the training effect can be remarkably enhanced.

APA, Harvard, Vancouver, ISO, and other styles

19

Helbert, Anne Laure, Wei Wang, Thierry Baudin, François Brisset, and Brisset Penelle. "Formation and Development of Strong Cube Recrystallization Texture in an Aluminium of Commercial Purity." Materials Science Forum 702-703 (December 2011): 391–97. http://dx.doi.org/10.4028/www.scientific.net/msf.702-703.391.

Full text

Abstract:

The goal of the present study inspired by previous works on high purity aluminiun was to manufacture aluminium sheets of commercial purity, grade 1050, with a strong cube texture. In this preliminary work on AA1050, sheets which cube volume fraction reaches 65% have been manufactured. Parameters controlling cube orientation development are mainly the solute dragging due to impurities in solid solution and the stored deformation energy. Besides the 85% cold rolling (CR), two extra annealings and a slight cold rolling are introduced in the processing route to increase the cube volume fraction. The cube orientation, whose substructure is equiaxed, is important for its recovery. It develops thanks to the difference of stored energy relative to that of its first neighbors; the slight cold rolling enhances growth of these cube grains.

APA, Harvard, Vancouver, ISO, and other styles

20

Tresidder, Martin, and Paul White. "Briefing: Design for manufacture and off-site construction at Woolston Wastewater Treatment Works (UK)." Proceedings of the Institution of Civil Engineers - Management, Procurement and Law 171, no. 4 (August 2018): 137–40. http://dx.doi.org/10.1680/jmapl.17.00031.

Full text

APA, Harvard, Vancouver, ISO, and other styles

21

Zainuddin, Muhammad, Sudarmiatin, and Agus Hermawan. "Development of Metal and Machinery Small and Medium Enterprises (SMEs) in West Lombok Regency with the Blue Ocean Strategy Approach." EKSYAR : Jurnal Ekonomi Syari'ah & Bisnis Islam 9, no. 2 (December 12, 2022): 136–43. http://dx.doi.org/10.54956/eksyar.v9i2.358.

Full text

Abstract:

Blue Ocean Strategy aims to open new market share to minimize competition with similar competitors. After receiving a touch from the West Lombok Regency Industry and Trade Service (Prindag Lobar), the Metal and Machinery Community Activity Unit in West Lombok initially produced gates, trellises and other similar works, creating quite a lot of competition. So that with the guidance of the Service which offers solutions with the Blue Ocean Strategy, the metal and machine industry (SMEs) in West Lombok Regency can compete. This study used a qualitative method, data obtained from in-depth interviews with section heads of the metal, machine, electronics and transportation equipment (ILMEA) industry, descriptive analysis and source triangulation. This article reveals that Blue Ocean Strategy manufactures metal products and machinery in different segments. The Blue Ocean Strategy segment is offered in the form of changing the mindset and technical skills of metal and machining (SME) players. Metal and machinery SMEs are trained to manufacture machine products needed by the food and beverage industry. One of the concrete steps is the manufacture of machines for making palm sugar machines, coffee roasting machines and other processing machines. This has an impact on the shift of the metal and machine SME segment from household products to processed machine products.

APA, Harvard, Vancouver, ISO, and other styles

22

Way, Yusoff, Mohamad Ali Hasanudin Hafis, and Md Amir Hamzah Md. Shukri. "A Surgical Training Biomodel Manufacture Using Fused Deposition Modeling." Advanced Materials Research 588-589 (November 2012): 1764–66. http://dx.doi.org/10.4028/www.scientific.net/amr.588-589.1764.

Full text

Abstract:

The purpose of this research is to fabricate maxillofacial biomodel and apply the rapid prototyping technology using Fused Deposition Modeling (FDM) in solving some surgical problem in medical field. The build biomodel will be used in educational and pre-medical surgical environments. Besides, it can simplify the complex surgical procedures and the visualization of anatomical structures. A machine that works under FDM principle will be used to produce a finished biomodel. Product analysis later is implemented to make the result more trustful. Thus, it is demonstrated that biomodel can help surgical planning and at the same time it will reduce costs, surgical times and infection risks in health care system.

APA, Harvard, Vancouver, ISO, and other styles

23

Gong, Hang, Yao Ping Li, and Jie Chao. "FSAE Race Car Engine Options on the Impact of Vehicle Design." Applied Mechanics and Materials 721 (December 2014): 28–31. http://dx.doi.org/10.4028/www.scientific.net/amm.721.28.

Full text

Abstract:

FSC is a Formula One car contest car works by the universities or auto-related professional school students team up to participate in the design and manufacture of automotive competition. All participating teams in accordance with the rules and race car manufacturing standards, in a year's time to design and manufacture an accelerating, braking, handling, and so has excellent performance of small single-seater racing leisure, to successfully complete all or Part of the event part of the game. This article discusses the single-cylinder engine and four-cylinder engine of the car design different vehicle.

APA, Harvard, Vancouver, ISO, and other styles

24

Du Pasquier, Jacqueline. "Cuir et porcelaine, une heureuse rencontre." Sèvres. Revue de la Société des Amis du musée national de Céramique 32, no. 1 (2023): 120–21. http://dx.doi.org/10.3406/sevre.2023.1639.

Full text

Abstract:

During a remarkable career at the Manufacture de Sèvres, Mireille Cousin has become one of the best painters of her generation. She has mastered the techniques that contribute to the excellence of the institution, has met prestigious artists whose works she has magnified and now directs within the manufacture, a school of painting on porcelain to transmit her knowhow to younger generations. Michel Roué has been able during his career to acquire knowledge of all the decoration and manufacturing techniques as well as managerial and transmission skills. He supervises about forty art technicians in a dozen workshops.

APA, Harvard, Vancouver, ISO, and other styles

25

Dudziak, Jacek, Paweł Guła, Arkadiusz Gawlik, and Jerzy Kondracki. "Design and manufacture of nacelles for small turboprop aircraft." Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering 231, no. 12 (August 14, 2017): 2239–47. http://dx.doi.org/10.1177/0954410017725544.

Full text

Abstract:

The aim of this paper is to present the results of prepreg nacelles design and manufacturing for I-31T aircraft. The work was part of the European Union project ‘Efficient Systems and Propulsion for Small Aircraft’ (ESPOSA). The new engine cowling design was preceded by computational fluid dynamics numerical analyses stage. Use of TP100 engine was assumed, which was installed on the I-31T aircraft in the framework of the ESPOSA project. This article presents the process of external geometry adjustment, chosen results of numerical analyses, 3D model design, manufacturing process and tests results. The new cowlings underwent ground and in-flight tests. Monitoring during the test included external and internal cowling temperatures. The collected test data were further analysed. Throughout accumulated energy in hot parts of the engine the temperature inside the engine nacelles rises. ‘Hot’ composite nacelles were used in order to withstand the impact of high temperature. In majority of modern aircraft propulsion systems, cowlings are made of composite. Currently, there is a trend to manufacture initially solution treated materials – i.e. glass and carbon fiber pre-pregs in out-of-autoclave process. Such an approach allows to accelerate the fabric layup process and achieve highly repeatable structure. Materials that are currently available in the market allow to manufacture the cowlings and simultaneous weight minimization. Owing to the applied 3D software for both design and manufacture of machining tools, it is possible to shorten the time of manufacturing a complete element. The cowlings were designed in cooperation with the NLR – Netherlands Aerospace Centre, who was a partner in the ESPOSA project and has experience in prepreg elements design. NLR was responsible for material selection and final part manufacturing. Tooling has been designed and manufactured in the Institute of Aviation in Warsaw. The assembly works were carried out by Zakłady lotnicze Margański & Mysłowski.

APA, Harvard, Vancouver, ISO, and other styles

26

Zharkova, Anastasiya A. "The socially dangerous consequences of environmental rules violation during a work (Russian Federation Criminal Code art. 246)." Yugra State University Bulletin 12, no. 1 (April 15, 2016): 231–33. http://dx.doi.org/10.17816/byusu2016121231-233.

Full text

Abstract:

The article is devoted to the analysis of socially dangerous consequences of violation of the rules of the environment by manufacture of works. The author proposes changes in the basic structure of article 246 of the Russian Criminal Code and the addition of its qualifying staff.

APA, Harvard, Vancouver, ISO, and other styles

27

Petrenko, Oleksii, Valerii Chikovani, Serhii Golovach, and Grygorii Golovach. "Experimental investigation of the maximum quality factor axes temperature deviation in metallic Coriolis vibratory gyroscopes resonator." MECHANICS OF GYROSCOPIC SYSTEMS, no. 42 (December 28, 2022): 69–79. http://dx.doi.org/10.20535/0203-3771422021268467.

Full text

Abstract:

A metallic cylindrical resonator is a well-known base detail of the significant part of Coriolis vibratory gyroscopes (CVG) [1] including a MEMS gyro. It own parameters just after mechanical manufacture in main are determine an advisability of further utilize and the future gyroscope accuracy potential. Initial testing CVG resonators directly after their manufacture often done using the optical method [2,3] or acoustic method [4,5]. Unfortunately investigated manufacture quality of the resonators by using acoustic method not very well describe in scientific literature. A paper presents the results of some extension acoustic investigations of the metallic CVG resonators. This result describes the behavior of maximum quality factor (Q-factor) axes and own resonant frequencies axes under stabilized temperature step influences and can be used in prediction for CVG bias minimization during it works in temperature range.

APA, Harvard, Vancouver, ISO, and other styles

28

Prema Kumari, P., K. Mercy Salima, and P. Ethalsha. "Studies on the Quality and Heavy Metals in Common Salt Production Using Sea Brine and Sub-Soil Brine in South Tamil Nadu, India." Asian Journal of Engineering and Applied Technology 4, no. 1 (May 5, 2015): 53–56. http://dx.doi.org/10.51983/ajeat-2015.4.1.745.

Full text

Abstract:

The manufacture of common salt using sea brine and sub-soil brine contain several chemical and trace metal elements.This study estimated the salt quality parameters like moisture content, insoluble matter, calcium sulphate, magnesium sulphate, magnesium chloride and sodium chloride content of the salt and also estimated the different trace metals like copper, iron, zinc, manganese and chromium in salts harvested from the Salt samples of two selected salt works, Kovalam SW1 (sea brine) and Puthalam SW2 (sub-soil brine) in Kanyakumari District and the two selected salt works, Vepalodai SW3 (sea brine) and Sahupuram SW4 (sub-soil brine) in Tuticorin District. The salt samples have maximum moisture content in Kanyakumari salt works than Tuticorin District because of the climatic conditions. The salt works using sea brine, harvested salt of the maximum mean sodium chloride content than sub-soil brine using salt works. In both the Districts, sea brine using salt works is having almost similar concentration of heavy metals, likewise sub soil brine using salt works.

APA, Harvard, Vancouver, ISO, and other styles

29

Rogge, Corina E., and Julie Arslanoglu. "Luminescence of coprecipitated titanium white pigments: Implications for dating modern art." Science Advances 5, no. 5 (May 2019): eaav0679. http://dx.doi.org/10.1126/sciadv.aav0679.

Full text

Abstract:

Material analysis of cultural artifacts can uncover aspects of the creative process and help determine the origin and authenticity of works of art. Technical studies on abstract expressionist paintings revealed a luminescence signature from titanium white paints whose pigments were manufactured by coprecipitation with calcium or barium sulfate. We propose that trace neodymium present in some ilmenite (FeTiO3) ores can be trapped in the alkaline earth sulfate during coprecipitation, generating a luminescent marker characteristic of the ore and process. We show that the luminescence is linked to a specific ilmenite source used in historic TITANOX pigments, is not present in pigments produced by more advanced chemistries, and provides dating information. Facile Raman-based detection of this luminescence, along with characteristic peaks of rutile, anatase, calcium sulfate, or barium sulfate, can identify the type of titanium white pigment and narrow its manufacture date range.

APA, Harvard, Vancouver, ISO, and other styles

30

Lefebvre, Thierry. "Construire un livre. Dans l’« atelier » des Pharmaciens Bibliophiles." Revue d'histoire de la pharmacie 108, no. 412 (2021): 493–508. http://dx.doi.org/10.3406/pharm.2021.24478.

Full text

Abstract:

To build a book. In the «workshop » of «Les Pharmaciens Bibliophiles » – Using unpublished archives, the author tells about the design and manufacture of one of the most outstanding works of the society «L es Pharmaciens Bibliophiles » (The Pharmacists Bibliophiles) : the «M émoires » of the military pharmacist Sébastien Blaze, published in 1935.

APA, Harvard, Vancouver, ISO, and other styles

31

Babiak, Ihor, and Svitlana Vikhot. "RESEARCH OF A-IIIВ PERIODIC PROFILE REINFORCEMENT AND ITS APPLICATION PROSPECTS FOR SLABS OF SPANS OF BRIDGES." Dorogi i mosti 2023, no. 27 (April 25, 2023): 216–27. http://dx.doi.org/10.36100/dorogimosti2023.27.216.

Full text

Abstract:

Introduction. Metal reinforcement A-IIIв, manufactured from reinforcement A-III in accordance with GOST 5781 by pulling, was quite widely used for slabs of span structures of bridges in the period before 1991, as well as later. There is a need to repair such structures due to the exhaustion of their resource due to a significant duration of operation, damage due to the impact of means of destruction during hostilities. Often, the best option for repairing such spans is to replace a separate plate or plates with similar ones, since in this case there are no problems with the size of height, resting on existing supports, etc. Problem Statement. The vast majority of bridges in Ukraine, built in the period 1960-1991 and, to a large extent, in subsequent years, were designed according to typical projects. A large number of these bridges were built from girder slabs according to typical designs, where class A-IIIв reinforcement was used as prestressed reinforcement. These reinforcements were produced directly at the factories producing slabs structures from reinforcements of class A-III in accordance with GOST 5781 by pulling. To perform such works, the manufacturing plant must have appropriate equipment, qualified specialists, documentation, and obtain reinforcements of the required quality. As for the documentation, in the period up to 1991, such documentation was developed centrally and distributed to factories manufacturing structures. After 1991, this does not happen, the documentation is often not updated, which can be the reason for not ensuring the quality of the structures. Purpose. To analyze the documentation for the manufacture and use of reinforcement A-IIIв for the manufacture of slabs of span structures of bridges with a length of 12 m in accordance with the documentation VTP 21-86 (addition). To research the reinforcement A-IIIв, which is manufactured in accordance with the documentation YN 218 USSR – 026-84 directly at the manufacturing plant from the reinforcement of class A-III in accordance with GOST 5781 by pulling it for further use for the manufacture of slabs of span structures of bridges with a length of 12 m in accordance with documentation VTP 21‑86 (addition). Establish the possibility of using reinforcement A-IIIв in today’s conditions for the manufacture of slabs of span structures 12 m long in accordance with the documentation VTP 21-86 (addition) for the repair and construction of bridges.

APA, Harvard, Vancouver, ISO, and other styles

32

Maier, Johanna, David Werner, Vinzenz Geske, Thomas Behnisch, Mathias Ahlhelm, Tassilo Moritz, Alexander Michaelis, and Maik Gude. "Investigation of the Damage Phenomenology with Dependence on the Macroporosity and Microporosity of Porous Freeze Foams." Materials 16, no. 6 (March 21, 2023): 2484. http://dx.doi.org/10.3390/ma16062484.

Full text

Abstract:

Freeze Foams are cellular, ceramic structures with hierarchical pore structures that are manufactured using the direct foaming process. By tailoring their morphology and strength, these foam structures are able to cover a wide range of application. Earlier works identified that pore-forming influencing factors (water and air content, suspension temperature, as well as pressure reduction rate) dictate the constitution on a macroscopic and microscopic scale. Therefore, the ability to manufacture foams whose properties align with the component requirements would be an important step in advancing towards a widespread application of these promising materials. With this goal in mind, the correlation between the pore-forming influencing factors and the resulting mechanical properties was quantified. Foams with independently adjustable porosities were produced at the micro and macro scales and evaluated according to their material failure behavior under compressive loads. As a result, foams with determined macroporosities between 38 and 62%, microporosities between 25 and 42%, and compression strengths between 1 and 7 MPa with different material failure characteristics were manufactured and systematically investigated.

APA, Harvard, Vancouver, ISO, and other styles

33

Ganeshan, G. N., R. Kamalakannan, and S. Vijay. "Design, manufacture and sustainable analysis of biodegradable computer mouse using solid works and 3D printer." Materials Today: Proceedings 21 (2020): 56–59. http://dx.doi.org/10.1016/j.matpr.2019.05.360.

Full text

APA, Harvard, Vancouver, ISO, and other styles

34

Romadin, Achmad, Yoto Yoto, and Didik Nurhadi. "Career Identification of Production Operators’ Position in Manufacture Industries." Teknologi dan Kejuruan: Jurnal Teknologi, Kejuruan, dan Pengajarannya 44, no. 1 (August 4, 2021): 1. http://dx.doi.org/10.17977/um031v44i12021p1-9.

Full text

Abstract:

Graduating of Vocational High School in the manufacturing industry occupies job of production position. The demands of industrial needs are in the manufacturing sector. They want employees or labor that have told and professional competencies. Therefore, it is necessary to analyze and identify career in operator position. This study uses qualitative research. This research focuses on analysis of operator's position needs in the industry. Based on the results of the research, the work of production operators includes briefing, setting, operating, quality procedures, and engine maintenance. There are several competencies regarding the position of production operators, namely occupational health and safety, quality assurance, measuring instruments, hand tools, technical drawings, general machining, and special conditions. Production operators get salaries, which include grade-based salaries, and salary holidays. Susceptible salary obtained by production operator position gets a vulnerable salary based on the industrial area district minimum wage where he works.

APA, Harvard, Vancouver, ISO, and other styles

35

Novikova, O. "Qing monochrome porcelain from the Collection of the Bohdan and Varvara Khanenko National Museum of Arts." Research and methodological works of the National Academy of Visual Arts and Architecture, no. 27 (February 27, 2019): 168–77. http://dx.doi.org/10.33838/naoma.27.2018.168-177.

Full text

Abstract:

The article analyzes Qing monochrome products of Chinese porcelain and studies the complex technology of their manufacture. This publication is also devoted to the main identification problems of Chinese monochrome thin-walled ceramics and its terminology. When dating and attributing Chinese monochrome porcelain causes the most difficult problem. Thin-walled monochrome glaze ceramic products manufactured at different times are often distinguished only by barely noticeable changes in parts and other proportions of products. Furthermore, the plagiarism was uncharacteristic of Chinese, and the imitation and copying of works of past epochs, in their opinion, only confirmed the value of original works and even gave a sacred meaning to them. The basis for this approach was the idea of connection between epochs, the continuity of traditions and the respect to ancestors supported by the ruling elite, because it was a part of the official religion of the statе – Confucianism. The secret of regenerative firing has been discovered that restores the natural color of metals in their oxides in the glaze composition thanks to the carbon by giving the rich hue color intensity to the monochrome Chinese ceramics. The play of different colors achieved exclusively by ceramic techniques is very attractive, and products colored in such way are sometimes more expensive than the painted glazed ceramics. In Qing times ceramists manufactured a lot of porcelain products that mimicked samples of previous epochs. From time to time potters created almost exact copies of products, so it is sometimes difficult for present-day researchers to tell the difference between late imitations and original ancient works. That’s way the purpose of this article is to analyze works of Chinese Qing monochrome porcelain from the collection of the Bohdan and Varvara Khanenko National Museum of Arts, to demonstrate the manufacturing technology and terminological features and to specify attributions. This study has been illustrated by pieces from the Bohdan and Varvara Khanenko National Museum of Arts.

APA, Harvard, Vancouver, ISO, and other styles

36

Whitehouse, D. J. "A Philosophy of Linking Manufacture to Function— An Example in Optics." Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture 207, no. 1 (February 1993): 31–42. http://dx.doi.org/10.1243/pime_proc_1993_207_059_02.

Full text

Abstract:

It is well known that characteristics of a surface can be used to monitor the manufacturing process. It is also well known that the surface of a component is important, in many cases, in determining how well the component performs. Ideally, the manufacturing process should be picked to ensure that the part works satisfactorily. In this paper, as an example, the specific function of gloss is chosen as a requirement. It is then shown what sort of surface is most suitable for this and further how this surface should be made, thereby completing the chain from manufacture to function.

APA, Harvard, Vancouver, ISO, and other styles

37

Nutfullaeva, L. N., Sh N. Nutfullaeva, S. Sh Tashpulatov, M. S. Muminova, and L. M. Sayfullaeva. "Method of manufacturing working surfaces of ironing tables for wet-heat works of garments from composite materials." Journal of Physics: Conference Series 2388, no. 1 (December 1, 2022): 012010. http://dx.doi.org/10.1088/1742-6596/2388/1/012010.

Full text

Abstract:

Abstract The article studied the components, types and properties, as well as the classification of composite materials. The direction of use and methods for obtaining new structural materials are considered. The developed new technology for the production of composite materials is described, which is used for the manufacture of parts for ironing equipment of sewing enterprises. The method of forming the working surface of ironing tables from a new composite material is substantiated.

APA, Harvard, Vancouver, ISO, and other styles

38

Nagorniy, A. "ENERGY-SAVING ECOLOGICALLY CLEAN TECHNOLOGY OF SILICA BUILDING MATERIALS." Integrated Technologies and Energy Saving, no. 3 (September 12, 2022): 22–29. http://dx.doi.org/10.20998/2078-5364.2022.3.03.

Full text

Abstract:

The most widely used in construction materials industry are ceramic and lime bricks. Higher energy consumption and several ecological problems make their manufacture to become more and more expensive. The growing market of construction works and constant extension of real estate property increases the demand for cheap and new materials with desired features. As a result of many years intensive scientific researches there is now a practical possibility to offer an alternative and unique sand and water based products technology of manufacture (bricks, wall, floor and roofing tiles, sanitary materials, heat insulating and acid proof materials, decorations etc.) – all of them of desired size, shape and colour. The experience of the structural materials technology development shows that building industry will obtain improved service life and performance from quartz sand suspensions as field installations will continue to move toward adopting and utilizing practices based on technology described herein, rather than on cement technology. This type of manufacture is very profitable for the countries having the deposits of sand everywhere situated and being extracted at very low prices. Relative to conventional construction materials sand and water made products (SWP) with mechano-chemical binders will continue to gain in popularity because of the following advantages: low energy consumption and low prices for the products; ecological safety of the manufacture process and of the ready-made products; good mechanical and design properties; moisture and cold proofness; surface need not be fired; no shrinkage of the products after drying; simple to manufacture a variety of different products; ready availability and flexibility in design; absence of manufacture wastes.

APA, Harvard, Vancouver, ISO, and other styles

39

Browne, Janet. "Charles Darwin as a Celebrity." Science in Context 16, no. 1-2 (March 2003): 175–94. http://dx.doi.org/10.1017/s0269889703000772.

Full text

Abstract:

ArgumentSeveral recent works in sociology examine the manufacture of public identities through the notion of celebrity. This paper explores the imagery of Charles Darwin as a nineteenth-century scientific celebrity by comparing the public character deliberately manufactured by Darwin and his friends with images constructed by the public as represented here by caricatures in humorous magazines of the era. It is argued that Darwin’s outward persona drew on a subtle tension between public and private. The boundaries between public and private were blurred by the ritual of Darwin “showing” himself in the flesh, either at home to visitors or, more rarely, on public occasions. The reputation for privacy and illness that he built up added materially to this public face. By contrast, caricatures tended to depict him as an ape. These apish representations played a significant role in associating Darwin, rather than any other thinker, with the notion of evolution, and in creating an alternative public persona over which he had no direct control.

APA, Harvard, Vancouver, ISO, and other styles

40

Gómez, Laura, J. Escobar, Maria Teresa Colomer, and Rodrigo Moreno. "Manufacture of YSZ-LSM Semi-Cell by Colloidal Processing." Materials Science Forum 727-728 (August 2012): 746–51. http://dx.doi.org/10.4028/www.scientific.net/msf.727-728.746.

Full text

Abstract:

Yttria stabilized zirconia (YSZ) is the most common electrolyte in solid oxide fuel cells (SOFC). The planar configuration is widely used for designing single cells, in which a thick cathode layer can be used as the supporting electrolyte film. The manufacture of the semi-cell formed by anode and electrolyte has been widely studied and there are many works dealing with its colloidal processing. However, the semi-cell formed by cathode and electrolyte has received much lower attention. This work deals with the manufacture of a semi-cell consisting of YSZ as electrolyte and strontium-doped lanthanum manganite (LSM) as a cathode through a colloidal processing route. The colloidal behavior of diluted suspensions of YSZ and the rheology of their concentrated suspensions were studied as a function of deflocculant content, mixing time by using ultrasounds probe and ageing time. The colloidal stability of aqueous suspensions of LSM was studied by measuring the zeta potential as a function of pH and deflocculant content. These concentrated suspensions were used to obtain thick self-sustained substrates by casting methods. The YSZ electrolyte and LSM cathode were prepared by tape casting in water medium.

APA, Harvard, Vancouver, ISO, and other styles

41

Feng, Ming Tang, and Zhi Gang Li. "Research on the Manufacture of Multi-Sipe Radial Tire Molds by EDM." Advanced Materials Research 668 (March 2013): 451–59. http://dx.doi.org/10.4028/www.scientific.net/amr.668.451.

Full text

Abstract:

It is a technical challenge to insert sipes in a multi-sipe radial tire mold. The authors have invented a new method to make tire mold patterns by EDM which has solved the problems of inserting the sipes, characterized in that the patterns and sipes can be made at the same time, and as they are made as one body after EDM, there is no need to manually insert the sipes. The multi-sipe tire molds made by EDM meet the technical standards of famous international tire companies, and evaluation results show that this process works very well in the manufacture of complicated tire molds.

APA, Harvard, Vancouver, ISO, and other styles

42

Hsu, Chang-Hsien. "Process Performance Analysis and Improvement for the Manufacture of 6063 Aluminum Alloy." Metals 10, no. 5 (May 8, 2020): 605. http://dx.doi.org/10.3390/met10050605.

Full text

Abstract:

As industrial manufacturing technologies continuously improve, many conventional industrial materials are struggling to meet the needs of today’s industries. Aluminum alloys are currently the most extensively used non-ferrous metal in the industry, whose properties include corrosion resistance, high strength, and high ductility. As a result, they are widely used in many products, such as doors and windows, vehicles, and electronics. Pure aluminum though, is a very soft, silver-white metal, so to increase its strength, aluminum alloy manufacturers add in various chemical elements (such as magnesium, silicon, and zinc) according to international standards, and then adjust the proportions based on customer needs. If the chemical element composition does not meet specification requirements, it will affect the quality of the aluminum alloy product or even delay delivery and subsequently impact the operational performance of the manufacturer. To ensure and increase aluminum alloy quality, this study used a combined Six Sigma quality index (SSQI), Qpc, to develop a multi-characteristic quality analysis model (MCQAM) with five steps for the aluminum alloy industry. A practical example with a manufacturer specializing in producing 6063 aluminum alloys in Taiwan is given to demonstrate the effectiveness and feasibility of this proposed approach. The result shows that the proposed method not only effectively improves the quality of 6063 aluminum alloy, but also enhances its performance and capability (that is, corrosion resistance increases by 17%, strength increases by 8%, and stiffness increases by 3%). Finally, future works are also discussed in this context.

APA, Harvard, Vancouver, ISO, and other styles

43

Ford, George. "A Counterfactual Impact Analysis of Fair Use Policy on Copyright Related Industries in Singapore: A Critical Review." Laws 7, no. 4 (October 5, 2018): 34. http://dx.doi.org/10.3390/laws7040034.

Full text

Abstract:

In a 2014 article appearing in Laws, Ghafele and Gibert presented evidence on the economic impacts of Singapore’s change in its fair use policies showing a large effect on industries that manufacture goods useful for private copying of copyrighted works and no effect on the copyright industries. As detailed in this Comment, Ghafele and Gibert’s empirical analysis fails to shed light on the consequences of modifications to fair use policies.

APA, Harvard, Vancouver, ISO, and other styles

44

Walker, J. H., and L. B. Walpole. "A Major Advance in the Manufacture of Large Structural Beams and Columns." Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture 203, no. 4 (November 1989): 253–59. http://dx.doi.org/10.1243/pime_proc_1989_203_076_02.

Full text

Abstract:

This paper describes the enhancement project undertaken at British Steel's Teesside Works which enabled the Universal Beam Mill to become the first such mill in the Western World to introduce the use of continuously cast slabs as the feedstock for rolling heavy beams and columns. The change necessitated construction of a new slab reheating furnace, a complete modification of mill rolling practice and involved several engineering developments needed to enable the new process to be successfully integrated within the existing plant. The new process has resulted in significant benefits for the mill's customers and has greatly improved mill performance through a reduction in material yield losses, higher output speeds and improved plant availability.

APA, Harvard, Vancouver, ISO, and other styles

45

Xu, Hua, and Rong Tian Wen. "The Research and Manufacture of Tundish of the New Flexible Planer Double-Enveloping Transmission Equipment." Advanced Materials Research 645 (January 2013): 459–62. http://dx.doi.org/10.4028/www.scientific.net/amr.645.459.

Full text

Abstract:

To solve the technology improve of the tundish turning equipment of the steel works of the steel company, the flexible transmission equipment of the planer double-enveloping is designed based on the advanced technology of the planer double-enveloping toroidal worm pairs. the characters of the planer double-enveloping toroidal worm pairs and its research processing are introduced in this paper.

APA, Harvard, Vancouver, ISO, and other styles

46

Yetri, Yuli, Eka Sunitra, Ali Siddik, Rakiman Rakiman, and Haris Haris. "Pembuatan Cetakan Pellet Elektroda Super Kapasitor Untuk Penyimpan Energi." Jurnal Teknik Mesin 16, no. 2 (December 1, 2023): 139–44. http://dx.doi.org/10.30630/jtm.16.2.1150.

Full text

Abstract:

The design of a tool for printing supercapacitor electrodes has been completed. The basic material for the electrode is cocoa pod skin. The purpose of this research is to manufacture and assemble a laboratory-scale supercapacitor chip mold, which is used to facilitate the manufacture of the chip that functions as an electric current store. After the design process is complete, it is continued to manufacture supercapacitor chips using a press system. The actuator/pressurizer uses a hydraulic jack with a capacity of 50 tons, and a mold made of ST 37 and ST 60 steel. The mold is above the jack assisted by a steel frame as a pressure barrier. And a dial indicator as a marker to stop pressing by the jack. The process of making supercapacitor chip molds starts from cutting, drilling, turning, surface grinding, and welding. After the process of making components and assembling is complete, a trial of the tool is carried out to find out whether the tool works well. After a series of tests were carried out, it turned out that this pellet mold was able to print well without any cracks.

APA, Harvard, Vancouver, ISO, and other styles

47

Newark, Cormac. "Metaphors for Meyerbeer." Journal of the Royal Musical Association 127, no. 1 (2002): 23–43. http://dx.doi.org/10.1093/jrma/127.1.23.

Full text

Abstract:

The avowed inability of nineteenth-century Parisian critics to express in words their impressions of music (whether instrumental or lyric) doubtless has something to do with a more or less general lack of training, but in the case of the works of Meyerbeer it also points to a particular idea of opera. An intense interest in orchestration (outlined here in reviews of Robert le diable, Les Huguenots, Le prophète and L'Africaine; also in Berlioz's Grand traité d'instrumentation et d'orchestration modernes) is articulated in enthusiastic examination of the instruments themselves, and in striking metaphors of science, technology and manufacture. The presence of this gloss on Meyerbeer in otherwise Romantic appreciations (for example Balzac's Gambara) suggests a way of reading opera reception in tune with the urban culture of the period.

APA, Harvard, Vancouver, ISO, and other styles

48

LEE, W. H., C. H. CHUNG, and C. L. CHUNG. "ELECTRO-DISCHARGE METHOD TO MANUFACTURE SUPERPARAMAGNETIC IRON OXIDE NANOPARTICLES." International Journal of Nanoscience 02, no. 04n05 (August 2003): 271–82. http://dx.doi.org/10.1142/s0219581x03001292.

Full text

Abstract:

Functional nanocrystalline metallic iron powder is produced by the method of electro-discharge in the low oxygen environment of water. In order to obtain superparamagnetic iron oxide Fe 3 O 4, the manufacturing Fe particles were oxidized in the oxygen-rich water to continue oxidation process. Besides, the nanocrystalline Fe particle will be oxidized at temperatures of 200° C , 250° C , 300° C , 350° C , 400° C , 500° C and 600° C for 1 h in air to produce iron oxide α- Fe 2 O 3. The X-ray diffraction, SEM and transmission electron microscope (TEM) were used to analyze the crystal structure and the powder morphologies. The results showed that pure Fe and FeO with a pretty narrow particle size distribution ranges from 1 nm to 10 nm were obtained by the method of electro-discharge. After oxygen-rich oxidation treatment the γ- Fe 2 O 3 and Fe 3 O 4 were obtained at room temperature in 10 days. Thereafter, no more transformation was found in water environment. This result proves that Fe 3 O 4 can be a stable superparamagnetic iron oxide. However, for the Fe particles heat-treated at temperatures of 200 to 600° C , α- Fe 2O3 was formed at temperatures above 300° C for 1 h treating time. Further application studies of this material will be presented in our future research works.

APA, Harvard, Vancouver, ISO, and other styles

49

Katkalov, V. B., and M. L. Morozova. "Served space: new achievements and perspectives." Spacecrafts & Technologies 6, no. 3 (September 26, 2022): 206–17. http://dx.doi.org/10.26732/j.st.2022.3.06.

Full text

Abstract:

The number of works aimed at developing technologies for services in space has increased significantly over the past five years. In addition to such industrial giants as Orbital-ATK, Northrop Grumman, MDA, Maxar Technologies, startups are also entering the service market that develop and demonstrate practically operating technologies. Given this trend, it is expected that maintenance in space will become a hot topic over the next few years. The article discusses the designed and operating service spacecraft of foreign countries, the state and directions of their development. Brief characteristics and capabilities of service spacecraft are given. The directions of solving the main tasks for the design and manufacture of promising service spacecraft are outlined. Satellites MEV-1 and MEV-2, manufactured by Northrop Grumman, ELSA-d, manufactured by Astroscale and SSTL, and See also OSAM-1 by Maxar Technologies, which allows robotic refueling in space and demonstrates the possibility of constructing large structures in space without direct human involvement. The results of a study carried out using available Internet sources are summarized and presented in this material. The purpose of the article is to analyze the need, ways and methods of development of services, to assess the prospects of the technologies used.

APA, Harvard, Vancouver, ISO, and other styles

50

Lobsang, Yongdan. "The Translation of European Astronomical Works into Tibetan in the Early Eighteenth Century." Inner Asia 17, no. 2 (December 9, 2015): 175–98. http://dx.doi.org/10.1163/22105018-12340041.

Full text

Abstract:

It has long been assumed that European scientific knowledge arrived in Tibet with the agents of the British Empire in the early twentieth century and furthermore that Tibetans did not engage with scientific knowledge until recent years. However, this is far from the case; from the beginning of the eighteenth century onwards Tibetans not only translated a great number of Jesuit astronomical works into Tibetan by order of the Kangxi Emperor (1654–1722), they also reformed one of the calendars in use in Amdo using the principles described by Danish astronomer Tycho Brahe (1546–1601). In this paper I look at how the relevant translations were done, by whom and in what historical context. I shall also explore the process by which the Jesuit-inspired astronomical and calendar turned out to be the catalyst for the adoption, reformation and manufacture of the Qing imperial calendar in Amdo.

APA, Harvard, Vancouver, ISO, and other styles

Journal articles on the topic 'Manufacture and works'

Create a spot-on reference in APA, MLA, Chicago, Harvard, and other styles