Academic literature on the topic 'Hydrophobic siloxane'

Hydrophobic materials are among the most commonly used coatings for building exterior cladding. In fact, these products are easily applied to an existing surface, significantly reduce water absorption and have a minimal impact on the aesthetic properties. On the other hand, although these products have a proven effectiveness, their long-term durability to weathering has not yet been systematically studied and completely understood. For these reasons, this study aims to correlate the effect of artificial aging on the moisture transport properties of hydrophobic treatments when applied on building exterior claddings. Three hydrophobic products (an SiO2-TiO2 nanostructured dispersion; a silane/oligomeric siloxane; and a siloxane) were applied on samples of limestone and of a cement-based mortar. The moisture transport properties (water absorption, drying, water vapor permeability) of untreated and treated specimens were characterized. Furthermore, the long-term durability of the specimens was evaluated by artificial aging, that is, hygrothermal cycles (freeze–thaw and hot–cold). All treatments have significant hydrophobic effectiveness and improve the long term-durability of the treated specimens. However, the results showed that the three hydrophobic products have different effectiveness and durability, with the SiO2-TiO2 nanostructured dispersion being the most durable treatment on limestone, and the siloxane the most suitable for cementitious mortar.

In this study, the influence of nanosilicon(IV)-oxide (with hydrophobic and hydrophilic functionalized surfaces) on the properties of siloxane elastomers was studied. The elastomers were prepared from vinyl and hydrogen oligosiloxanes, while the nanocomposites were obtained by addition of nanofillers at different concentrations (1, 5, 10 and 20 wt%). The chemical structure of the obtained materials was analyzed by Fourier transform infrared spectroscopy. Transmission electron microscopy confirmed good dispersion of the hydrophobic filler within the polymer matrix, while the hydrophilic filler formed a net on the siloxane sample. Type of the filler modification did not affect hardness of the siloxane hybrid materials, while the samples with the highest content of hydrophobic nanosilica have shown the highest value of tensile strength. Influence of the nanosilica type on thermal degradation of elastomeric materials was investigated by using thermogravimetric analysis, while the influence of the fillers on the phase transition temperature was analyzed by differential scanning calorimetry. Lower compatibility of the hydrophobic matrix and hydrophilic filler caused a decrease in the crystalline melting temperature with the lowest value determined for the sample with the highest filler loading. Increase in the nanofiller content resulted in the improved thermal stability of the obtained hybrid materials.

Impact of the addition of silane and siloxane based hydrophobic powders on cement based mortar was studied. Effect of powder addition on mechanical properties and water absorption of cement based mortar is described. Impact of accelerated ageing, including UV radiation, and rain-sun cycles on hydrophobic performance was assessed, demonstrating excellent durability of silane-based hydrophobic performance.

Two series of crosslinked poly(urethane-ester-siloxane)s were synthesized from ?,?-dihydroxy-(ethylene oxide-poly(dimethylsiloxane)-ethylene oxide) (EO-PDMS-EO), 4,4?-methylenediphenyl diisocyanate and Boltorn? hyperbranched polyesters of the second and third pseudo generation, by a two-step polymerization in solution. The effect of the EO-PDMS-EO content and functionality of the applied crosslinking agent on the morphology and surface properties of the prepared poly(urethane-ester-siloxane)s was investigated by FTIR spectroscopy, small-angle X-ray scattering (SAXS), atomic force microscopy (AFM), scanning electron microscopy (SEM) and water absorption measurement. Different techniques (FTIR peak deconvolution, SAXS and AFM) revealed that decrease of the crosslinking agent functionality and EO-PDMS-EO content promotes microphase separation in the synthesized poly(urethane-ester-siloxane)s. SEM analysis and water absorption experiments showed that due to the hydrophobic character of EO-PDMS-EO and its ability to migrate to the surface of poly(urethane-ester-siloxane)s, samples synthesized with higher EO-PDMS-EO content and crosslinking agent of lower functionality have more hydrophobic surface and better waterproof performances. The obtained results indicate that the synthesis of poly(urethane-ester-siloxane)s based on EO-PDMS-EO and Boltorn? hyperbranched polyesters leads to the creation of networks with interesting morphological and surface properties, which can be easily tailored by changing the content of EO-PDMS-EO segment or functionality of hyperbranched polyester.

The electrical efficiency of photovoltaic panels is affected by many environmental parameters, which have a negative impact on system electrical efficiency and cost of energy, dust and increased panel temperatures being the most serious in the MENA region. In this work, a few organic-based self-cleaning coatings are developed, and their effects on PVs’ electrical efficiency re assessed for polycrystalline panels exposed to natural soiling conditions outdoors at El-Sherouk City. The results show that monolithic hydrophobic-based coatings using paraffine and dimethyl-siloxane show up to 14.3% improvement in the electrical efficiency of the PV panels, but the role of nanoparticles TiO2 and Al2O3 addition needs further investigation. Hydrophobic-based coatings using dimethyl-siloxane reduce the coated panels’ surface temperature compared with the uncoated panel.

Hydrophobic impregnations often referred to as water repellent agents, today mainly consisting of alkylalkoxysilanes, are often used on concrete to prolong the service life of the structure. This is accomplished by protecting the reinforcement bars from chlorides or by changing the moisture content inside. When the concrete is treated with a water repellent agent the properties of the surface layer becomes hydrophobic and thereby water droplets are stopped from entering, still allowing water vapour to pass through. This change can reduce chloride ingress and stop heavy rain from penetrating through the surface layer. This thesis presents results concerning how the properties of concrete are affected by a hydrophobic impregnation. Moisture transport and fixation in the surface layer of the concrete are studied as well as the secondary effects of more practical use such as the effect on chloride ingress, water absorption and humidity level. It also presents results on how the penetration depth and concentration of the water repellent agent (i) depend on a number of parameters, and (ii) affect the outcome of the treatment. Water repellent treatments on a number of different concrete structures in Stockholm, ranging from tunnel to high-rice building, are evaluated as well. The three most important factors for the penetration of any water repellent agent into concrete are time, porosity and degree of saturation. A semi-empirical equation is derived that gives an idea on how much these factors affect the efficient penetration depth of the water repellent agent. The depth and concentration have a major effect on the performance of the treatment. The moisture diffusion coefficient for a water repellent treated concrete is close to constant and not nearly as dependent on the relative humidity (RH) as for untreated concrete. Unlike untreated concrete, where capillary suction plays an important role for the moisture transport at high RH, the vapour transport is the dominant transport mechanism even at high RH for water repellent treated concrete. The moisture fixation is affected by a water repellent treatment and the effect is clearest at high moisture levels. The main reason for this is that the capillary porosity is affected by the treatment to a relatively high degree while the gel porosity to a large extent remains unaffected. A hypothesis is presented which suggests that the RH inside the concrete at the time of the treatment affects not only the depth and concentration but also in which range of pore radii the water repellent agent is present and active. The durability of hydrophobic impregnations can be divided into surface effects and in depth effects. The first is sensitive to the environmental and mechanical loadings and normally disappears within a year while the later can be long lasting if a sufficient depth is reached. Hydrophobic impregnations are not the answer to all problems in concrete related to moisture, but if correctly used it can prolong the service life of the structure which will lead to savings of natural resources and thus both economical and environmental savings for the community.
Vattenavvisande impregneringsmedel, som i dagsläget till största del består av alkylalkoxysilaner, används ofta på betong för att förlänga livslängden på konstruktionen. Detta syfte uppnås genom att armeringen skyddas mot klorider eller att fukthalten inuti betongen sänks. När betongen impregneras ändras ytskiktets fuktmekaniska egenskaper från hydrofila till hydrofoba vilket gör att vattendroppar kan stoppas medan vattenånga tillåts passera. Dessa förändrade egenskaper kan medföra att kloridinträngningen minskar och att kraftiga regn inte tränger genom det impregnerade skiktet. Denna avhandling presenterar resultat om hur betongen påverkas av en vattenavvisande impregnering. Fukttransport och fuktfixering i betongens ytskikt har undersökts men även sekundära effekter som kloridinträngning, vattenabsorption och förändring i fuktinnehåll vilka alla är av större praktisk nytta. Avhandlingen presenterar också resultat om vilka faktorer som påverkar impregneringens inträngningsdjup och koncentration samt vilken betydelse dessa har för funktionen. För att utvärdera impregneringars effekt i olika miljöer har ett stort antal objekt i Stockholm undersökts, innefattande olika konstruktioner från en tunnel till höghus. Impregneringens inträngningsdjup och koncentration har en avgörande betydelse för dess funktion. De tre viktigaste faktorerna för alla impregneringsmedels inträngning i betong är tid, porositet och fuktnivå. En semiempirisk ekvation har tagits fram där det framgår hur dessa tre faktorer påverkar det slutliga inträngningsdjupet för impregneringen. Till skillnad från obehandlad betong är transportkoefficienten för en impregnerad betong nästan oberoende av den relativa fuktigheten (RF) i omgivningen. Vid höga RF, där största delen av fukttransporten i obehandlad betong sker på grund av kapillärkrafter, är ångtransporten fortfarande den dominerande transportmekanismen i impregnerad betong. Fuktfixeringen i betong påverkas av en impregnering och effekten är störst vid höga RF. Det är dock tydligt att en viss mängd fukt finns inuti den impregnerade betongen. Detta kan förklaras med att största delen av kapillärporerna påverkas av impregneringen medan gelporerna förblir obehandlade. Resultaten indikerar också att fuktnivån vid impregneringstillfället avgör vilken del av porsystemet som kan behandlas och inte bara koncentrationen och inträngningsdjupet. Långtidsegenskaperna hos impregneringen kan delas upp i yt- och djupeffekt. Effekten på ytan avtar normalt sett inom ett år på grund av damm och partiklar, UV-ljus, slitage mm. Djupeffekten påverkas däremot inte av dessa faktorer och kan finnas kvar i decennier. Vattenavvisande impregneringar är inte lösningen på alla fuktrelaterade problem i betong, men om de används på rätt sätt så kan det förlänga livslängden på många konstruktioner. Detta leder till ett bättre hushållande med naturresurser och därmed både ekonomiska och miljömässiga besparingar för samhället.
QC20100715

Most of the topics dealt with in this thesis belong to surface science. The starting point was the fundamental understanding of phenomena at the oxide-gas interface and the effect of its modification. Such knowhow was then used to solve (or, at least, to attempt to solve) issues of critical impact in everyday life: the increasing lifetime of building materials employed in low-impact smart houses; the fouling prevention in electroanalytical sensors for neurotransmitter detection; the unspecialized laboratories accessibility to microlithography, critical to device miniaturization. These challenges might seem not related, but they actually share deep scientific and technological foundations. The physicochemical modification of oxide surfaces, the creation of organic/inorganic hybrids and the exploiting / the enhancing of semiconductor peculiar properties allowed us, starting from the foundation, the realization of proof-of-concept protocols and devices, ready for the pre-commercial development. The Leitmotif of my research was the synthesis and the modification of titanium dioxide surfaces. TiO2 has been the main character in physico, physicochemical and material science researches of the last 50 years. Biocompatibility and low cost make it engaging for many applications. Its (near-UV active) semiconductor features, well known and abundantly investigated by the scientific community, are acquiring central interest also in many markets with the development of self cleaning coatings, windows and asphalts, anti-fogging mirrors and self-sterilizing surgery rooms and instrumentations. New generation batteries and solar cells are going to be developed as commercial prototypes. One of the biggest challenges in the titania fundamental research is the enhancement of activity in the solar spectrum. First, the most recent aspects in titania doping and promotion were touched. While, in the last twenty years, great effort has been made in the mono-atomic doping of titania and in the understanding of the influence of the dopant position in the titania lattice and its electronic behavior, the most recent literature describes the co-promotion of the material by two (or more) atoms doping. The metal/non-metal codoping seems especially promising; the synergetic effect of the two atoms in the TiO2 lattice was both theoretically and experimentally proved. In this contest, the N/Nb codoping was analyzed, investigating the effect of the atoms in the lattice from morphological (surface area, porosity and crystallographic structure) and electronic point of view (EXAFS, UV-Vis absorption and EPR analyses). N/Nb codoping was compared with N/Ta co-doped samples, synthesized by two different procedures. The photoactivity of the two sample families was tested by a model reaction (the degradation of ethanol, throughout acetaldehyde intermediate) both under UV and solar simulated irradiation. Then, a different approach in the modification of surfaces was tested. The assembly of organic/inorganic hybrids was tested; thanks to the formation of organic mono- or multi-layers at the surface,they can tune the chemistry, the polarity and the adhesion properties of the interface. Siloxanes were used as active agents, thanks to their compatibility with oxide materials and, especially, for the ability to self-assemble at the surface to form a monolayer. Siloxanes are able to react with the -OH groups at the surface, chemisorbing and polymerizing at the interface in such a way to form a monolayer with tunable functionalities. Many different silanes were tested and their dipole momenta were related to their wettability properties. Such siloxanes chemisorb strongly both from the gas phase and the liquid phase. Their reactivity, both on smooth and rough surfaces, was tested vs the temperature of functionalization in gas phase. Many characterization techniques were adopted to understand the behavior of such molecules from a molecular point of view: magnetic (solid state NMR), microscopic (SEM, TEM, AFM), optical and electrochemical (CV and EIS). The science of adhesion and wettability was also adopted for the development of superhydrophobic coatings. Titanium dioxide particles with engineered morphology were used as the best candidate to create superhydrophobic/superhydrophilic patch-wise surfaces, exploiting their photoactivity (photolithograpy). The core of the thesis was the synthesis, modification and application of transparent photoactive thin films. A procedure for the synthesis of smooth, transparent and photoactive TiO2 thin layers was developed, and used to produce highly applicative devices and protocols. Such synthetic strategy is highly tunable and reproducible; the obtained films are robust and active and, most of all, require simple instrumentation (sol-gel procedure), which is highly appealing for the market. The films were properly characterized both form the morphological/mechanical and photochemical point of view. Apart their transparency and their thickness, the films were highly crystalline (pure anatase phase). Such procedure was firstly designed as a proof-of-concept for self-cleaning windows, but, thanks to its versatility and the high activity of the films, it leads the path towards highly applicative procedures and devices. The smoothness and the photoactivity brought me to the field of photolithograpy, especially in the direction of microlithography. The high activity of the titania allowed the use of safe and low-energetic lamps. No collimation was required to obtain a resolution lower than 5 µm. First of all, I tested the lithography on siloxane monolayer films, as a proof-of-concept of resolution and efficiency. But siloxanes, as many other self-assembled monolayer molecules, can be the pillars for 3D fabrication. Such monolayers were used as polymerization initiators for polymer brushes. If the initiators of polymerization are patterned, patterned polymer brushes will be obtained. That was the first report of polymer-brushes lithography exploiting the photoactivity of TiO2. Remote photocatalytic lithography makes this procedure extremely versatile. Exploiting the remote photocatalysis, in principle, any material can be used as a support for patterned polymer brushes growth (provided that the initiator are able to graft the surface). The developed protocol for the synthesis of TiO2 thin films was also used to design and engineer complex electrodes for cyclovoltammetric analyses of biological samples. Electrochemistry seems to be the best candidate for the development of an analytical option with sensitivity comparable with present analytical procedures but reduced time-per-analysis and cost. Unfortunately, catecholamines chemisorb and polymerize on metal and oxide electrodes quickly, making the device useless. Covering the electrode by a homogeneous, nano-porous thin layer of titania makes the surface photoactive. That is the first example in literature of self-cleaning nano-engineered electrodes for cyclic voltammetry. After the detection, also in simulated human serum and liquor, a fast and simple irradiation of the device, under non-hazardous UV-A lamp, degrades all the fouling on the surface without altering its features. The sensor, after each UV treatment, recovers its pristine performances, with full recovery in terms of selectivity and sensitivity. Irradiation trials were also performed directly in the analytical mixture, as a proof of concept for on-site application. Modern era requires flexible and light materials for the building industry. Polymers are acquiring more and more interest thanks to their increasing performances and their smart properties. The drawbacks of such materials are connected to the low resistance to the UV light, the softness and the difficulties in cleaning procedure. The use of organic/inorganic hybrid, or better the coverage of plastic materials with an oxidic thin layer, can solve many of these problems, lengthening the lifetime of such materials. If the covering oxide is also photoactive, the material can be self-cleaned when exposed to solar light. That is a big chemical challenge, because of many synthetic problems. Two different approaches were tested to solve this relevant issue. On one side, the hydrophobicity of ionic liquid modified SPES (sulfonated polyether sulfone) was combined with designed morphological features to confer superhydrophobicity. On the other side, the polymeric surface was covered with a transparent titania layer active in the near UV-region, able to mineralize organic molecules chemisorbed at the surface. Eventually, a different approach to modify oxidic (and not only) surfaces is the creation of a homogeneous layer of Ag nanoparticles by an innovative microwave procedure. That simple and accessible strategy allowed us to produce plasmonic surfaces (thanks to the dimension and the homogeneity of the Ag particles) with countless applications. The layer was shown to be a very active substrate for surface enhancement Raman spectroscopy (SERS). Thanks to the versatility of the synthetic method, all shapes and dimensions can be covered. That makes it a perfect candidate for the production of new generation of SERS sensors. The sensitivity towards molecules of environmental and biomedical interest was proved.

Sur une surface superhydrophobe, les gouttes d'eau rebondissent ou roulent grâce au piégeage de poches d'air entre les microstructures (état « Fakir »). Cependant, cette même surface est inefficace vis à vis d'une goutte d'alcool qui s'imprègne dans les aspérités. Afin d'étendre l'effet superhydrophobe à une large gamme de liquides, il est nécessaire de fabriquer des microstructures présentant une géométrie dite « ré-entrante ». Ces surfaces sont alors dites superomniphobes. Dans un premier temps, nous présentons deux procédés de fabrication permettant d'obtenir de telles surfaces à base de polymère, ou à base de polymère et de nitrure de silicium. Dans un second temps, nous étudions les propriétés d'adhésion (hystérésis d’angle de contact) de ces surfaces en fonction des paramètres géométriques des microstructures. Les résultats mettent en évidence un effet de saturation non décrit par les modèles théoriques existants. Afin de contribuer à la compréhension des mécanismes physiques responsables de ce phénomène, nous présentons une expérience permettant d'imager la déformation de l'interface liquide sur ces surfaces. Les mesures montrent la formation de micro ponts liquides durant le démouillage. Nous montrons que l'analyse des modes d'instabilité de ces ponts liquides permet de justifier qualitativement la saturation observée. Ces expériences mettent également en évidence le dépôt de nano-volumes de liquide sur les structures suite au démouillage de la surface. L'hétérogénéité de ces dépôts est corrélée à la dynamique de la ligne triple. Ce phénomène présente des perspectives intéressantes pour le dépôt contrôlé et passif de colloïdes ou biomatériaux
On a superhydrophobic surface, water drops rebound and roll off due to trapping of air pockets between micro or nano structures (“Fakir” state). However, the same surface is inefficient toward alcohol drops which spread in the asperities.In order to extend the superhydrophobic effect to a wide range of liquids, it is necessary to design microstuctures with a “re-entrant” geometry. These surfaces are then called superomniphobic. In a first time, we present two microfabrication processes enabling to obtain such surfaces in polymer, or in polymer and silicon nitride. In a second time, we study the adhesion properties (contact angle hysteresis) as a function of microstructures geometrical parameters. The results point out a saturation effect which is not described by actual models. In order to better understand the underlying physical mechanisms responsible for this phenomenon, we present an experiment enabling to visualize the liquid interface deformation on these surfaces. Measurements show that dewetting occurs through the formation of micro capillary bridges. By analyzing the instability modes of these liquid bridges, we show that it is possible to qualitatively demonstrate the observed saturation effect. The experiments also point out the presence of nano-scale liquid volumes on the micro-structures resulting from de-wetting of the surface. The heterogeneities of these deposits is correlated to the triple line dynamic. The phenomenon presents interesting perspectives for the controlled and passive deposition of colloids or bio-materials

Structural charge arises on the surfaces of soil mineral particles in which either cation vacancies or isomorphic substitutions of cations by cations of lower valence occur. The principal minerals bearing structural charge are therefore the micas (Section 2.2), the 2:1 clay minerals (Section 2.3), or the Mn(IV) oxide, birnessite (Section 2.4). These three classes of mineral are all layer type and the cleavage surface on which their structural charge is manifest is a plane of O ions. The plane of O ions on the cleavage surface of a layer-type aluminosilicate is called a siloxane surface.This plane is characterized by hexagonal symmetry in the configuration of its constituent O ions, as shown at the top of Fig. 2.3 and, more explicitly, on the right side of Fig. 2.4, where a portion of the siloxane surface of the micas is depicted. Reactive molecular units on the surfaces of soil particles are termed surface functional groups. The functional group associated with the siloxane surface is the roughly hexagonal (strictly speaking, ditrigonalbecause the hexagonal symmetry is distorted when the tetrahedral sheet is fused to an octahedral sheet to form a layer) cavity formed by six corner-sharing silica tetrahedra. This cavity has a diameter of about 0.26 nm. The reactivity of the siloxane cavity depends on the nature of the electronic charge distribution in the layer structure. If there are no nearby isomorphic cations substitutions to create a negative charge, the O ions bordering the siloxane cavity function as an electron cloud donor that can bind molecules weakly through the van der Waals interaction. These interactions are akin to those underlying the hydrophobic interaction, discussed in Section 3.5, because the O in the siloxane surface can form only very weak hydrogen bonds with water molecules. Therefore, uncharged patches on siloxane surfaces may be considered hydrophobic regions to a certain degree, with, accordingly, an attraction for hydrophobic organic molecules. However, if isomorphic substitution of Al3+ by either Fe2+ or Mg2+ occurs in the octahedral sheet, the resulting structural charge is manifest on the siloxane cavities, as discussed in Section 2.3.

Because of the great importance of the surface properties of the polysiloxanes, this topic is treated separately in this chapter. Hydrophobic polysiloxanes having simple aliphatic or aromatic side groups have surfaces that show essentially no attraction to water. In fact, polysiloxanes can serve as water repellants. This property is very useful for applications such as protective coatings on historical monuments and for controlling the surfaces of other polymers, sensors, and quantum dots. Hydrophobic surfaces can be readily regenerated if the surface becomes damaged. Regeneration occurs by rearrangements of the polysiloxane chains so that the hydrophobic methyl groups are once again covering the surface. The flexibility of the siloxane chain backbone facilitates this process. It is also possible to prepare hydrophobic films using methyl-modified siloxane melting gels. Glass surfaces or wool fibers can be coated with polydimethylsiloxane (PDMS) to make them more hydrophobic. In some cases, it is necessary to modify a polysiloxane surface to make it hydrophilic or hydrophobic. Hydrophobization is one aspect of the general topic of modifying and managing the properties of polymer surfaces. An important example involves soft contact lenses that contain PDMS, which is often used because of its very high permeability to oxygen, which is required for metabolic processes within the eye. Such lenses do not feel comfortable however because they do not float properly on the aqueous tears that coat the eye. There are a number of ways to modify the surfaces. There is even a way to make “unreactive” silicones react with inorganic surfaces. In some applications it is useful to have hydrophilicity in the bulk of the polymer instead of just at the surface. One way of doing this is by simultaneously end linking hydrophilic poly(ethylene glycol) (PEG) chains and hydrophobic PDMS chains. Another way is to make a PDMS network with a trifunctional organosilane R’Si(OR) end linker that contains a hydrophilic R’ side chain, such as a polyoxide. Treating only the surfaces is another possibility, for example, by adding hydrophilic brushes by vapor deposition/hydrolysis cycles. Such hydrophilic polysiloxanes can also serve as surfactants.