Academic literature on the topic 'Epoxidové hmoty'

The thesis deals with the pouring of epoxy materials over LED strips. The research part contains an introduction to photometry and summarizes the types of potting compounds along with their characteristics. The practical part delves into the effect different amount of pigment has on the photometric properties. This is assessed based on verified measurements performed with the help of a goniophotometer on samples with different amounts of pigment, which were created using an integration sphere. Furthermore, a brightness analysis and a long-term outdoor test were performed.

This diploma thesis deals with the fundamental properties of epoxide mixtures, as determining of these fundamental properties of epoxide mixtures could in the case of favorable results lead to diminishing the amount of defects in epoxide-embedded instrument transformers. As the influence of effects in the manufacturing process of transformers causing poor quality is very extensit, the biggest emphasis is laid capitally on the influence of the epoxide casting mixture composition. The thesis describes the manufacture technology including used methodics and materials. The compositions of epoxide resins and the mechanisms of their curing. Also, the definitions of fundamental properties of dielectric materials and the description of diagnostic methods used to relative permitivity, dissipation factor and inner resistivity are included. suitable casts of acquired samples were set and dried out within the experimental part, followed by measurement of fundamental electrical properties in temperature and frequency relations. Hereafter a comparison of individual samples and the evaluation of their electrical properties will be carried out.

Presented master's thesis is focused on studying electroinsulating epoxy resin-based sealings. It describes the chemical composition, production, properties and measuring methods of basic electric quantities of these materials. The aim of the thesis is to compare several sets of samples of composite epoxy resins with different kinds of micro-ground siliceous sand as a filling. The temperature and frequency dependence of relative permittivity, dissipation factor and inner resistivity are measured for given samples.

Submitted paper deals with the current condition of electrical insulating substances used in electrical engineering, including the requirements on their electric and mechanical qualities. Another part of this paper constitutes a set of samples of epoxy resins and through and application of appropriate diagnostical methods the characterization of their attributes in the wide temperature range.

The diploma thesis deals with the development of polymeric repair mortars in two qualitative levels ECONOMY and PREMIUM, designed especially for heavy engineering plants and the energy industry. In order to effectively withstand difficult industrial conditions, the developed materials should meet the highest requirements such as increased chemical and heat resistance, excellent adhesion to the concrete substrate, minimal shrinkage and other physical and mechanical properties. The PREMIUM level is aimed to achieve maximum physical and mechanical properties. Within the economy version, the emphasis is placed not only on very good properties, but also the possibility capability of reducing price of the resulting material. The partial aim of this work is the efficient use of secondary raw materials, mainly based on industrial waste in the form of fillers to the developed polymeric repair mortars.

Crystallisation of epoxy resins based on bisphenol A and bisphenol F is the natural property of these oligomers. However, manufacturers of paints and other systems based on these epoxy resins, strive to slow down the crystallisation process as much as possible, thereby prolonging the shelf life and improving the competitiveness of their products. The main aim of the thesis is generalisation of the factors influencing the crystallisation process of epoxy resins based on bisphenol A and bisphenol F, verifying new approaches to the possibility of influencing the crystallisation process and determining the possibility of using a certain degree of epoxy resins crystallinity based on bisphenol A and bisphenol F in the preparation and production of epoxy resinbased coating systems.

The doctoral thesis deals with finding the use of some waste and secondary raw materials in the production of special polymer remediation materials for concrete, which could be applied even in constructions, where extreme mechanical and chemical load is occurred. The aim of this doctoral thesis is experimental examination of the possibility of using selected types of waste, including hazardous waste which represent the highest risk to environment, and secondary raw materials as a substitute for the currently used primary fillers in order to reduce the ecological footprint of the product itself. Some types of secondary raw materials, such as filter fly ash contaminated by flue gas denitrification process, are no longer used as a concrete admixture or partial cement substitution due to unwanted release of toxic ammonia (NH3). Mainly for this reason, the thesis deals with the progressive utilization of such types of secondary raw materials as well as with another currently unused waste into polymeric patching, grouting and anchoring materials while preserving or improving the final properties compared to reference materials using only primary raw materials. The result of this thesis is to find out suitable formulations for efficient preparation of special polymeric remediation materials for concrete containing waste and secondary raw materials as fillers. The partial aim of the thesis and a the scientific contribution is an observation of the developed materials internal structure using a modern device, CT tomography, an influence of the filler type on the long-term durability, and last but not least the observation of the rate of pollutants incorporation, found in hazardous waste, into the polymeric matric with the aid of EDX and FTIR analysis.

This thesis deals with problems of electrical insulation materials based on epoxy composites used in the electronics industry. This thesis is divided into theoretical part focused on composite materials, their technological processing and diagnostics. It also describes dielectric materials, their properties and events taking place in their structure. The experimental section describes the measurement of electrical properties of samples of electrical insulating materials with different types of fillers.

The diploma thesis deals with development of a new progressive anchor material on the polymer base. Nowadays, it is effort to utilize secondary raw materials in building industry as much as possible both from an environmental aspects in order to save primary energy sources and the reduction of waste and also due to economic reasons. Therefore, there is an effort to utilize high amount of suitable and appropriately treated secondary raw materials into the anchor materials. The main aim of this work is to develop high quality anchor material characterized by excellent ratio between speed and strength growth, high chemical resistance, thermal resistance and particularly minimal shrinkage. This new material is designed especially for anchoring building structures heavy machines steel barriers and other elements.