Academic literature on the topic 'Electrical machines and drives'

The industrial application of electric machines has grown in the last decades, thanks to the development of microprocessors and power converters, which have permitted their use as variable-speed drives. Although three-phase machines are the common trend, the interest of the research community has recently focused on machines with more than three phases, known as multiphase machines. The principal reason lies in the exploitation of their advantages in terms of reliability, i.e., post-fault operating capability. Additionally, multiphase machines provide a better current distribution among phases, and lower current harmonic production in the power converter, than conventional three-phase machines. However, multiphase drive applications require the development of complex controllers to regulate the torque (or speed) and flux of the machine. In this regard, direct torque controllers have appeared as a viable alternative due to their easy formulation and high flexibility to incorporate control objectives. However, these controllers face some peculiarities and limitations in their use that require attention. This work aims to tackle direct torque control as a viable alternative for the regulation of multiphase drives. Special attention will be paid to the development of the control technique and the expected benefits and limitations in the obtained results. Case examples based on symmetrical five-phase induction machines with distributed windings in the motoring mode of operation will be used to this end.

The usage of multiphase electrical drives expands the operation possibilities of electrical machines and opens new directions of research on inverter-fed electrical machines. With an increasing number of phases, the standard approach of the electromagnetic design of machines has to be generalized to m-phase systems, which is not usually respected in the literature focused on electric machine design, and it is rarely published. This paper summarizes the specific problems linked with the design of machines with different numbers of phases, focusing on the winding design and the calculation of equivalent circuit parameters. In addition to the direct effect of different numbers of phases, the impact of injecting higher order time harmonic components on the electromagnetic design of electric machines is analyzed. The obtained analytical results are verified by the measurement of a nine-phase experimental induction motor.

This thesis is concerned with the investigation and development of methods to monitor the condition of electrical machines, with particular reference to induction machines fed from variable frequency, power electronic supplies. A variety of techniques are suggested whereby the faults that most commonly afflict electrical machines can be identified. Techniques involving the detection and analysis of line current, frame vibration, and leakage magnetic field are proposed and developed to take account of the rich spectrum of harmonics that can be injected through the use of power electronic inverters. To do this it was necessary to produce methodologies that could differentiate between spectral components originating in the inverter, and those produced as a result of the fault. As an extension, two further monitoring techniques were developed in an attempt to provide a fully comprehensive strategem for assessing the health of electrical drives. They are sequence component monitoring, and pulsed eddy current monitoring. The former is an adjunct to those techniques previously mentioned, and when used in combination with them leads to a greater security of diagnosis. The use of pulsed eddy currents is aimed at the on line detection of material failure in the rotating shafts of the machines. For each technique suggested, a comprehensive theoretical basis is provided, and its effectiveness verified by suitable experiment.

In the present thesis, a new methodology of diagnosis based on advanced use of time-frequency technique analysis is presented. More precisely, a new fault index that allows tracking individual fault components in a single frequency band is defined. More in detail, a frequency sliding is applied to the signals being analyzed (currents, voltages, vibration signals), so that each single fault frequency component is shifted into a prefixed single frequency band. Then, the discrete Wavelet Transform is applied to the resulting signal to extract the fault signature in the frequency band that has been chosen. Once the state of the machine has been qualitatively diagnosed, a quantitative evaluation of the fault degree is necessary. For this purpose, a fault index based on the energy calculation of approximation and/or detail signals resulting from wavelet decomposition has been introduced to quantify the fault extend. The main advantages of the developed new method over existing Diagnosis techniques are the following: - Capability of monitoring the fault evolution continuously over time under any transient operating condition; - Speed/slip measurement or estimation is not required; - Higher accuracy in filtering frequency components around the fundamental in case of rotor faults; - Reduction in the likelihood of false indications by avoiding confusion with other fault harmonics (the contribution of the most relevant fault frequency components under speed-varying conditions are clamped in a single frequency band); - Low memory requirement due to low sampling frequency; - Reduction in the latency of time processing (no requirement of repeated sampling operation).

Field oriented control (FOC) and direct torque control (DTC) are the two most important control strategies for modern advanced machine drives. Field oriented control (FOC) has been widely used as the industrial motor drives. The direct torque control has been recently developed by Takashi and has shown great potential in machine drive applications. This thesis discusses the performances of direct torque control on AC machine drives including the industrial workhorse induction machines (IM) and permanent magnet synchronous machines (PMSM). Both of the IM and PMSM dynamics models are derived in details in the thesis. By applying nonlinear filtering techniques, the sensorless direct torque control of AC machine drives are studied. MATLAB simulations have shown the efficacy and superior performance of the resilient extended Kalman filter over the traditional extended Kalman filter for direct torque control applications.

The awareness of the human responsibility in global warming has led to various private and public initiatives to reduce the emission of greenhouse gases, up to international level. In this context the development of renewable technologies in two sectors having an important ecological footprint, i.e. production of electricity and transportation, is targeted.In the firstly mentioned sector, the progression of wind energy is at present the most rapid among all renewable energies. But wind turbines still suffer from a global lack of reliability and accessibility compared to classical power plants, leading to potentially important production losses and repair costs. The first part of the present work focuses on the improvement of the electrical chain reliability by the combination of an estimator and a fault-detection algorithm to achieve sensor-fault tolerance, taking benefit from the already available measurement redundancies on doubly-fed-induction-machine (DFIG) drives.Estimators and sensor-fault detection and isolation (FDI) in DFIGs have been the object of many research papers. However, most of them only consider one unique type of measurement and only a few works consider magnetic saturation. A new combination of a closed-loop observer with a cumulative-sum-based FDI technique, considering magnetic saturation and using limited computational resources is proposed here to estimate electromagnetic torque, rotor currents and position for sensor-fault detection and tolerance. This algorithm is then validated in steady state and in case of moderate transients, unbalanced conditions and misestimation of DFIG parameters. The estimator can also start on the fly during the start-up process of the generator.In the transportation sector, new hybrid and full-electric vehicles start to be visible on the roads, but still need important technological improvements in terms of autonomy, performances, but also produced noise and vibrations. The objectives of the second part of this doctoral thesis are related to this last challenge and consist of the experimental investigation of noise, vibration and harshness (NVH) aspects of an 8/6 switched-reluctance machine (SRM) designed for an electrical vehicle (EV).The NVH issues of SRMs, limiting their usage in automotive and other domains, have been the subject of various papers. However, most of them focus on modal analysis or detailed phenomena, while a global evaluation of NVH aspects of SRMs in normal working conditions is rarely made, as well as the use of reproducible sound metrics. A global and relatively fast experimental method to assess the evolution of noise and vibration is proposed. Tests are performed in transient regime, using continuously varying working conditions when possible, for the excitation of a large band of frequencies. The resulting current, radial vibration and acoustic noise are presented as spectrograms for an easy distinction of affected and unaffected frequencies and compared with the associated loudness and sharpness.Furthermore, the implementation of a new faster-sampled current-hysteresis controller has allowed to improve the quality of the control and of the acoustic noise by reducing the current-ripple amplitude and the excitation of resonances. The various tests show that the switching frequency has to be high enough to avoid exciting the ovalization mode of the SRM, but not too high to avoid producing a too sharp noise. The ripple amplitude also has to be considered to limit the loudness. Therefore, soft chopping, or a reduced DC-bus voltage at low speeds, has to be preferred with a relative small hysteresis bandwidth. Finally, the case of an open-phase fault has been investigated showing amplified even current orders in the vibration and acoustic-noise plots.
La prise de conscience de la responsabilité humaine dans le réchauffement climatique est à la source de nombreuses initiatives publiques et privées parfois internationales pour réduire les émissions de gaz à effet de serre. Dans ce contexte, le développement de technologies durables dans deux secteurs à forte empreinte écologique est visé: la production d'énergie électrique et les transports. Dans le premier secteur, la progression de l'éolien est à présent la plus rapide parmi toutes les énergies renouvelables. Cependant, les éoliennes souffrent d'un manque global de fiabilité et d'accessibilité par rapport aux centrales électriques classiques, ce qui conduit potentiellement à des pertes de production et des coûts de réparation importants. La première partie de ce travail se focalise sur l'amélioration de la chaîne électrique en la rendant tolérante aux défauts de capteurs au moyen de la combinaison d'un estimateur et d'un algorithme de détection de défauts, tirant avantage de la redondance de mesures déjà présente sur les entraînements à machines asynchrones à double alimentation (MADA). Les estimateurs et la détection et l'isolation de défauts de capteurs sur les MADA a fait l'objet de nombreuses publications scientifiques. Cependant, la plupart d'entre elles considèrent un seul type de mesure et peu de travaux prennent en compte la saturation magnétique. Une nouvelle combinaison d'un observateur et d'un algorithme de détection de défauts de type ‘CUSUM', considérant la saturation magnétique et nécessitant une puissance de calcul limitée, est proposée dans cette thèse pour l'estimation du couple électromagnétique, des courants et de la position rotoriques en vue d'obtenir la tolérance aux défauts de capteurs. Cet algorithme est validé en régime permanent et cas de transitoires modérés, de tensions du réseau déséquilibrées et d'erreurs d'estimation des paramètres de laMADA. L'estimateur est aussi capable de démarrer seul lors du démarrage de la génératrice. Dans le secteur des transports, des véhicules hybrides et électriques commencent à être visibles sur les routes, malgré que des progrès technologiques importants en termes d'autonomie, de performances, mais aussi de bruits et vibrations soient encore nécessaires pour une utilisation plus intensive. L'objectif de la deuxième partie de cette thèse se rapporte à ce dernier défi et consiste à analyser les aspects acoustiques et vibratoires d'une machine à réluctance variable 8/6 conçue pour propulser un véhicule électrique. Ces problèmes acoustiques et vibratoires, qui limitent notamment l'usage de telles machines dans des applications de propulsion, ont été l'objet de divers articles scientifiques. Cependant, la plupart d'entre eux sont focalisés sur des analyses modales ou de phénomènes particuliers, alors qu'une évaluation globale des problèmes de bruit et de vibration des machines à réluctance variable en conditions normales de fonctionnement est rarement proposée, de même que l'utilisation de critères de qualité sonore. Une méthode expérimentale globale et relativement rapide pour évaluer l'évolution du bruit et des vibrations est proposée dans ce travail. Les essais sont réalisés en régime transitoire pour exciter une large bande de fréquences et en faisant varier continuellement, quand cela est possible, les conditions de fonctionnement. Les courants, vibrations radiales et bruits acoustiques résultants sont présentés sous formes de cartographies couleur pour une distinction aisée des fréquences affectées et non-affectées et comparés aux niveaux calculés de bruyance et d'acuité correspondants. Par ailleurs, la mise en place d'un nouveau régulateur à hystérèse en courant à plus grande fréquence d'échantillonnage a permis d'améliorer la qualité de la commande et du bruit acoustique associé en réduisant l'amplitude des oscillations de courant et l'excitation des fréquences de résonance. Les essais montrent que la fréquence de commutation doit être suffisamment élevée pour éviter l'excitation du mode d'ovalisation de la machine, mais pas trop pour éviter une trop grande acuité du son produit. L'amplitude des oscillations doit aussi être considérée pour limiter la bruyance. En conséquence, une commande en ‘soft chopping', ou une tension réduite du bus continu à basse vitesse, doit être combinée à une bande d'hystérèse relativement faible. Enfin, le cas d'un défaut de phase ouverte a été étudié et a montré une amplification des ordres pairs du courant dans les spectres vibratoires et acoustiques.
De bewustwording van de menselijke verantwoordelijkheid in de opwarming van de aarde heeft tot verschillende private en publieke initiatieven geleid om de uitstoot van broeikasgassen te verminderen. In deze context is de ontwikkeling van hernieuwbare technologieën hoofdzakelijk gericht op twee sectoren met een belangrijke ecologische impact: elektriciteitsproductie en transport.In de eerste sector ontwikkelt windenergie zich op dit moment sneller dan alle andere hernieuwbare energieën. Maar windturbines lijden nog steeds aan een gebrek aan betrouwbaarheid en toegankelijkheid, en dus aan potentieel hogere productieverliezen en herstelkosten, als ze met klassieke krachtcentrales worden vergeleken. In het eerste deel van deze doctoraatsthesis wordt op de verbetering van de elektrische keten geconcentreerd door de combinatie van een schatter en een foutdetectie- en -isolatiealgoritme (FDI-algoritme) om sensorfouttolerantie te verkrijgen dankzij de reeds aanwezige meetovertolligheid op dubbelgevoede inductiemachine (DFIG) aandrijvingen.Schatters en sensor-FDI-algoritmen zijn het onderwerp van vele wetenschappelijke artikelen geweest. Meestal wordt maar één sensortype beschouwd en met de magnetische verzadiging wordt niet vaak rekening gehouden. Een nieuwe combinatie van een schatter met gesloten terugkoppeling en een FDI-techniek gebaseerd op het ‘cumulative-sum' principe is voorgesteld. Zo kan het elektromagnetische koppel, de rotorstromen en positie worden geschat voor sensor FDI en fouttolerantie met beperkte rekenkosten en zonder de magnetische verzadering te verwaarlozen. Het algoritme wordt in stabiele toestand gevalideerd, maar ook in het geval van gematigde transiënte situaties, onevenwichtige netwerkomstandigheden en een verkeerde schatting van DFIG parameters. Het kan ook vanzelf starten tijdens de startprocedure van de generator.In de vervoersector beginnen hybride en elektrische voertuigen op de wegen te rijden. Maar vooreen intensiever gebruik van zo'n wagens zijn er nog technologische verbeteringen nodig met betrekking tot autonomie, prestaties en ook geluid en trillingen (NVH). Het tweede deel van de thesis betreft die laatste uitdaging en bestaat uit het experimentele onderzoek van geluid en trillingen op een 8/6 variabelereluctantiemachine (SRM) ontwikkeld voor elektrische voertuigen.De NVH-problemen van SRM's beperken hun gebruik in automobiele en andere toepassingen enonderzoek wordt erover voortgezet. Vele wetenschappelijke artikelen focussen toch op modale analyse of gedetailleerde fenomenen terwijl een globale evaluatie van NVH aspecten in SRM's in gewone operatiecondities nauwelijks wordt gemaakt. Hetzelfde geldt voor het gebruik van reproduceerbare geluidsmetrieken. Een globale en vrij vlugge experimentele methode is hier voorgesteld om het NVH gedrag te schatten. Testen worden in transiënte situaties uitgevoerd om een brede frequentieband te exciteren, indien mogelijk met voortdurend variërende condities. De gemeten fasestroom, trilling en geluid worden als kleurmappen geplot om het verschil tussen beïnvloede en niet geaffecteerde frequenties te vergemakkelijken en met de berekende akoestische luidheid en scherpte vergeleken.Bovendien heeft de implementatie van een sneller bemonsterd stroomhysteresisregelaar geleid tot een verbetering van de regulatie- en akoestische kwaliteit door de amplitude van de stroomrimpeling en de excitatie van resonantiefrequenties te verminderen. De testresultaten tonen dat de schakelfrequentie voldoende hoog moet zijn om de excitatie van de ovale vervormingsmode te vermijden, maar niet te hoog om de scherpte van het geluid te beperken. De amplitude van de rimpel beïnvloedt ook de luidheid en daarvoor moet in aanmerking worden genomen. Bijgevolg zou ‘soft chopping'mode, of een lagere spanning op de DC-bus bij lage toerentallen, met een relatief klein hysteresisband beter worden gebruikt. Uiteindelijk wordt het geval van een openfasefout bestudeerd en onthult versterkte gelijke frequentievolgorden in de trilling- en geluidplots.
Doctorat en Sciences de l'ingénieur et technologie
info:eu-repo/semantics/nonPublished

High performance variable speed induction motor drives have been commercially available for industrial applications for many years. More recently they have been proposed for applications such as hybrid automotive drives, and some pump applications on more electric aircraft. These applications will require the drive to operate in the presence of faults i.e. they must be “Fault Tolerant” and be capable of “Fault Ride Through”. The aim of this project was therefore to investigate fault ride through control strategies for induction motor drives, particularly with respect to open circuit winding or power converter faults. Three objectives were identified and addressed to meet this aim. a) A new simulation model for an induction motor was created which reflects both saturation and space harmonics effects within the drive under both symmetric (healthy) and asymmetric (faulted) conditions. The model has a relatively low computational requirement to allow it to be used in conjunction with the simulation of high performance control algorithms and power electronic equipment. For operation in both healthy and faulty conditions, comparisons show that the simulated saturation and space harmonic effects match those obtained from an experiment system. Therefore this model is a very useful tool for the development and optimisation of new control strategies for fault tolerant drive systems. b) A novel on-line fault detection and diagnosis algorithm based on the measurement of the third harmonic component in the motor line currents has been proposed. The location of the open circuit fault is detected based on detecting a magnitude reduction for the third harmonic component of the current flowing to the motor terminals, and can be implemented in real time to give a fast response with little additional computational overhead. c) A new open circuit fault tolerant control strategy has been designed for a delta connected induction machine suddenly affected by an open circuit winding fault. The fault ride through is achieved without any modification to either the power converter or the motor circuit. A novel feedforward compensation algorithm is introduced which considerably reduces the current and the torque ripple in the faulted drive motor. Two methods for controlling the neutral point voltage are also presented so that the available voltage capacity of the inverter is maximised in both normal and fault mode. For high speed operation, two different methods for field weakening control are presented, so that the available voltage capacity is maximized in both normal and fault mode. This thesis describes the theoretical derivation of the new models and algorithms, and presents experimental results from a 4kW laboratory prototype to validate the proposals. The full fault tolerant system is experimentally demonstrated on a delta connected machine which suffers an open circuit winding fault. The improved motor performance under fault conditions is clearly seen.

Traditional high speed machinery actuators are powered and coordinated by mechanical linkages driven from a central drive, but these linkages may be replaced by independently synchronised electric drives. Problems associated with utilising such electric drives for this form of machinery were investigated. The research concentrated on a high speed rod-making machine, which required control of high inertias (0.01-0.5kgm2), at continuous high speed (2500 r/min), with low relative phase errors between two drives (0.0025 radians). Traditional minimum energy drive selection techniques for incremental motions were not applicable to continuous applications which require negligible energy dissipation. New selection techniques were developed. A brushless configuration constant enabled the comparison between seven different servo systems; the rate earth brushless drives had the best power rates which is a performance measure. Simulation was used to review control strategies, such that a microprocessor controller with a proportional velocity loop within a proportional position loop with velocity feedforward was designed. Local control schemes were investigated as means of reducing relative errors between drives: the slave of a master/slave scheme compensates for the master's errors: the matched scheme has drives with similar absolute errors so the relative error is minimised, and the feedforward scheme minimises error by adding compensation from previous knowledge. Simulation gave an approximate velocity loop bandwidth and position loop gain required to meet the specification. Theoretical limits for these parameters were defined in terms of digital sampling delays, quantisation, and system phase shifts. Performance degradation due to mechanical backlash was evaluated. Thus any drive could be checked to ensure that the performance specification could be realised. A two drive demonstrator was commissioned with 0.01kgm2 loads. By use of simulation the performance of one drive was improved by increasing the velocity loop bandwidth fourfold. With the master/slave scheme relative errors were within 0.0024 radians at a constant 2500 r/min for two 0.01 kgm^2 loads.

Thesis (Ph. D.)--Mechanical Engineering, Georgia Institute of Technology, 2008.
Committee Chair: Steven Y Liang; Committee Member: Chen Zhou; Committee Member: David G Taylor; Committee Member: Min Zhou; Committee Member: Shreyes N Melkote.

The thesis describes an investigation into methods for the specification, design and implementation of computer control systems for flexible manufacturing machines comprising multiple, independent, electromechanically-driven mechanisms. An analysis is made of the elements of conventional mechanically-coupled machines in order that the operational functions of these elements may be identified. This analysis is used to define the scope of requirements necessary to specify the format, function and operation of a flexible, independently driven mechanism machine. A discussion of how this type of machine can accommodate modern manufacturing needs of high-speed and flexibility is presented. A sequential method of capturing requirements for such machines is detailed based on a hierarchical partitioning of machine requirements from product to independent drive mechanism. A classification of mechanisms using notations, including Data flow diagrams and Petri-nets, is described which supports capture and allows validation of requirements. A generic design for a modular, IDM machine controller is derived based upon hierarchy of control identified in these machines. A two mechanism experimental machine is detailed which is used to demonstrate the application of the specification, design and implementation techniques. A computer controller prototype and a fully flexible implementation for the IDM machine, based on Petri-net models described using the concurrent programming language Occam, is detailed. The ability of this modular computer controller to support flexible, safe and fault-tolerant operation of the two intermittent motion, discrete-synchronisation independent drive mechanisms is presented. The application of the machine development methodology to industrial projects is established.

Compact, electric drives for automotive traction applications represent animportant enabler towards realizing tomorrow’s fossil free transport solutions.One attractive solution is to integrate the power electronic converter withits associated electric machinery into a single unit. This thesis, along withits appended papers, considers design and analysis of electric machinery forintegrated electric drives intended for automotive applications. Particular focusis put on permanent-magnet synchronous machines (PMSMs) with interiormountedpermanent magnets combined with modular converter topologies.In the first part of the thesis, different converter concepts and windingarrangements suitable for an integrated drive are reviewed. Compared to theconventional solution utilizing a three-phase two-level converter, a compactintegration can be implemented by physically splitting the converter and itsassociated dc-link capacitor into a number of converter submodules. Moreover,a modular concept also enables a certain level of fault tolerance.In the second part of the thesis, fractional-slot concentrated windings(FSCWs) are analyzed. First, a review for how to determine suitable slot, pole,and phase combinations is identified considering mainly the winding factor forthe main harmonic and the associated rotor losses. Then, integrated modularconverter concepts and associated winding configurations are considered andslot, pole and phase combinations that also comply with the consideredmodular converters are proposed. Further, two possible winding arrangementssuitable for the stacked polyphase bridges (SPB) and the parallel polyphasebridges (PPB) type converter are compared with respect to torque duringpost-fault operation in the event of failure of a single converter submodule.In the third part, an iterative process adopting both finite element analysisand analytical techniques is proposed for the design of PMSMs with interiormountedpermanent magnets and FSCWs. The resulting machine designsillustrate tradeoffs in terms of fault tolerance, power factor, torque density,and potential for field-weakening operation. From a given set of specifications,an experimental prototype is also designed and built.Finally, since a FSCW generally results in a large harmonic content ofthe resulting flux-density waveform, models for predicting eddy-current lossesin the permanent magnets are analyzed and compared. Particularly, modelsadopting different formulations to the Helmholtz equation to solve for the eddycurrents are compared to a simpler model relying on an assumed eddy-currentdistribution. Boundaries in terms of magnet dimensions and angular frequencyare also identified in order to aid the machine designer whether the mostsimple loss model is applicable or not. With a prediction of the eddy-currentlosses in the permanent magnets together with a corresponding thermal model,predicted volumetric loss densities exemplified for combinations of slot andpole numbers common in automotive applications are presented along withthe associated thermal impact.

QC 20170530

For aerospace related electric systems, torque/force density, reliability and fault tolerance are of the utmost importance. A method by which high figures of reliability can be achieved is by eliminating any mechanical gearing or interconnection elements between the electrical machine and its mechanical load. This means that direct drive, electrical machines must be employed. However, to implement such solutions (without any mechanical advantages), electrical machines with excellent torque density (for rotational machines) and force density (for linear machines) performances are required. In this work, the main aim is to propose and investigate possible methods for extending and improving the torque/force density capabilities of high performance, state of the art, electrical machines (both rotational and linear). This is done in order to be able to meet the performance requirements while lacking the mechanical advantages synonymous with gearing and/or mechanical interconnections. Novel electro-magnetic and thermal management structures, detailed design and optimisation procedures for electrical machines are presented in this thesis. As vehicles to investigate these novel concepts, a tubular linear, permanent magnet motor and a rotational, synchronous permanent magnet motor are designed, built and experimentally tested. These machines which are both for aerospace related applications serve to show and validate the worthiness of the proposed, performance enhancement measures.

The article describes the components of methods of using mobile Internet devices in the formation of the general professional component of bachelor in electromechanics competency in modeling of technical objects: using various methods of representing models; solving professional problems using ICT; competence in electric machines and critical thinking. On the content of learning academic disciplines “Higher mathematics”, “Automatic control theory”, “Modeling of electromechanical systems”, “Electrical machines” features of use are disclosed for Scilab, SageCell, Google Sheets, Xcos on Cloud in the formation of the general professional component of bachelor in electromechanics competency in modeling of technical objects. It is concluded that it is advisable to use the following software for mobile Internet devices: a cloud-based spreadsheets as modeling tools (including neural networks), a visual modeling systems as a means of structural modeling of technical objects; a mobile computer mathematical system used at all stages of modeling; a mobile communication tools for organizing joint modeling activities.

Decarbonization and energy security in Europe are two faces of the same coin. They are both related to the large dependency of the European Union economy on fossil fuels, which today represent around 70% of the total supply of energy. The bulk of these energy resources are imported, with Russia being the largest supplier, accounting for 40% of natural gas and 27% of oil imports. However, fossil fuels are also the primary root cause of greenhouse gas emissions, and the European Union is committed to reduce those by 55% by 2030 (versus 1990). This report is based on the landmark research from the Joint Research Center of the European Commission, the “Integrated Database of the European Energy Sector”, which for the first time mapped actual energy uses for each country within the European Union, across 17 sectors of activity, with data granularity at the level of each process step (or end-use) of each of these sectors. Our approach here has been to systematically review these process steps (or end-uses) and qualify the extent to which they could be electrified, effectively removing the demand for fossil fuels as a result. We have focused only on those process steps where technology was already widely available and for which we evaluated the switch to be relatively easy (or attractive). In other words, we estimated the impact of rapid electrification of “easy to abate” activities. The conclusion of this evaluation is that the share of electricity demand in the final energy mix could jump from around 20% today to 50%, which would drive a reduction in emissions at end-use of around 1,300 MtCO2 /y, as well as a drop in natural gas and oil supply of around 50%. As a result of such transformation, electricity demand would nearly double, with the bulk of that growth materializing in the building sector. Short-term, the challenge of addressing climate targets while providing for energy security is thus intimately connected to buildings. While such transition would certainly require major infrastructure upgrades, which may prove a roadblock to rapid deployment, we find that the combination of energy efficiency measures (notably digital) and distributed generation penetration (rooftop solar) could significantly tame the issue, and hence help accelerate the move away from fossil fuels, with energy spend savings as high as 80% across some building types; a major driver of change. Beyond this, further potential exists for electrification. Other measures on the demand-side will include deeper renovations of the industrial stock (notably in the automotive, machinery, paper, and petrochemical industries for which our current assessment may be underestimated) and further electrification of mobility (trucks). The transition of the power system away from coal (and ultimately natural gas) will then also play a key role, followed ultimately by feedstocks substitution in industry. Some of these transitions are already on the way and will likely bring further improvements. The key message, however, is that a significant opportunity revolves around buildings to both quickly decarbonize and reduce energy dependencies in Europe. Rapid transformation of the energy system may be more feasible than we think. We notably estimate that, by 2030, an ambitious and focused effort could help displace 15% to 25% of natural gas and oil supply and reduce emissions by around 500 MtCO2 /y (note that these savings would come on top of additional measures regarding energy efficiency and flexibility, which are not the object of this study). For this to happen, approximately 100 million buildings will need renovating, and a similar number of electric vehicles would need to hit the road.

An analysis of the experience of professional training bachelors of electromechanics in Ukraine and abroad made it possible to determine that one of the leading trends in its modernization is the synergistic integration of various engineering branches (mechanical, electrical, electronic engineering and automation) in mechatronics for the purpose of design, manufacture, operation and maintenance electromechanical equipment. Teaching mechatronics provides for the meaningful integration of various disciplines of professional and practical training bachelors of electromechanics based on the concept of modeling and technological integration of various organizational forms and teaching methods based on the concept of mobility. Within this approach, the leading learning tools of bachelors of electromechanics are mobile Internet devices (MID) – a multimedia mobile devices that provide wireless access to information and communication Internet services for collecting, organizing, storing, processing, transmitting, presenting all kinds of messages and data. The authors reveals the main possibilities of using MID in learning to ensure equal access to education, personalized learning, instant feedback and evaluating learning outcomes, mobile learning, productive use of time spent in classrooms, creating mobile learning communities, support situated learning, development of continuous seamless learning, ensuring the gap between formal and informal learning, minimize educational disruption in conflict and disaster areas, assist learners with disabilities, improve the quality of the communication and the management of institution, and maximize the cost-efficiency. Bachelor of electromechanics competency in modeling of technical objects is a personal and vocational ability, which includes a system of knowledge, skills, experience in learning and research activities on modeling mechatronic systems and a positive value attitude towards it; bachelor of electromechanics should be ready and able to use methods and software/hardware modeling tools for processes analyzes, systems synthesis, evaluating their reliability and effectiveness for solving practical problems in professional field. The competency structure of the bachelor of electromechanics in the modeling of technical objects is reflected in three groups of competencies: general scientific, general professional and specialized professional. The implementation of the technique of using MID in learning bachelors of electromechanics in modeling of technical objects is the appropriate methodic of using, the component of which is partial methods for using MID in the formation of the general scientific component of the bachelor of electromechanics competency in modeling of technical objects, are disclosed by example academic disciplines “Higher mathematics”, “Computers and programming”, “Engineering mechanics”, “Electrical machines”. The leading tools of formation of the general scientific component of bachelor in electromechanics competency in modeling of technical objects are augmented reality mobile tools (to visualize the objects’ structure and modeling results), mobile computer mathematical systems (universal tools used at all stages of modeling learning), cloud based spreadsheets (as modeling tools) and text editors (to make the program description of model), mobile computer-aided design systems (to create and view the physical properties of models of technical objects) and mobile communication tools (to organize a joint activity in modeling).