Dissertations / Theses on the topic 'Development Power'
Create a spot-on reference in APA, MLA, Chicago, Harvard, and other styles
Consult the top 50 dissertations / theses for your research on the topic 'Development Power.'
Next to every source in the list of references, there is an 'Add to bibliography' button. Press on it, and we will generate automatically the bibliographic reference to the chosen work in the citation style you need: APA, MLA, Harvard, Chicago, Vancouver, etc.
You can also download the full text of the academic publication as pdf and read online its abstract whenever available in the metadata.
Browse dissertations / theses on a wide variety of disciplines and organise your bibliography correctly.
Stone, Michael H. "Power Development." Digital Commons @ East Tennessee State University, 2015. https://dc.etsu.edu/etsu-works/4581.
Full textStone, Michael H. "Power Development in Sport." Digital Commons @ East Tennessee State University, 2014. https://dc.etsu.edu/etsu-works/4563.
Full textStone, Michael H. "Power Development among Explosive Athletes." Digital Commons @ East Tennessee State University, 2007. https://dc.etsu.edu/etsu-works/4500.
Full textStone, Michael H., P. Cormie, Hugh S. Lamont, and Margaret E. Stone. "Development of Strength and Power." Digital Commons @ East Tennessee State University, 2016. https://www.amzn.com/0415578213.
Full textLiu, Ning. "Our Power over Our Power : A paradigm shift in thederegulated power market." Thesis, Uppsala universitet, Institutionen för geovetenskaper, 2014. http://urn.kb.se/resolve?urn=urn:nbn:se:uu:diva-235464.
Full textGammon, P. M. "Development of SiC heterojunction power devices." Thesis, University of Warwick, 2011. http://wrap.warwick.ac.uk/44625/.
Full textPiedra, Daniel Ph D. Massachusetts Institute of Technology. "Development of gallium nitride power transistors." Thesis, Massachusetts Institute of Technology, 2010. http://hdl.handle.net/1721.1/66454.
Full text"November 2010." Cataloged from PDF version of thesis.
Includes bibliographical references (p. 78-79).
GaN-based high-voltage transistors have outstanding properties for the development of ultra-high efficiency and compact power electronics. This thesis describes a new process technology for the fabrication of GaN power devices optimized for their use in efficient power distribution systems in computer micro-processors. An existing process flow was used to fabricate the baseline single-finger transistors and additional process steps were developed and optimized to fabricate multi-finger devices with total gate widths up to 12mm. These transistors offer the current and on-resistance levels required by future GaN-based power converters. Transistors with various gate widths were fabricated and characterized by DC and capacitancevoltage measurements to study how the main transistor metrics scale with gate width.
by Daniel Piedra.
M.Eng.
Lotter, Paul. "Development of feedforward RF power amplifier." Thesis, Cape Peninsula University of Technology, 2006. http://hdl.handle.net/20.500.11838/2206.
Full textElectronic communication systems have become an integral part of our everyday lives. RF (Radio Frequency) power amplifiers form part of the fundamental building blocks of an electronic communication system. RF power amplifiers can also be one of the major causes of distortion in an electronic communication system. This thesis describes the linearity requirement for a RF power amplifier that is used in a transmitter section of an electronic communication system. Furthermore, five different linearisation techniques are presented and their characteristics compared. Since a power amplifier employing the Feedforward linearisation technique was designed, built and tested, this thesis focuses on the Feedforward technique. The design methods for the various Feedforward components are presented. The measured parameters of the Feedforward linearised amplifier are compared with the measured parameters of a non-linearised amplifier.
Bevan, Huw R. "Power development in professional rugby players." Thesis, Swansea University, 2011. https://cronfa.swan.ac.uk/Record/cronfa42313.
Full textZhou, Yun, and Quanfeng Wang. "Wind power in China." Thesis, University of Gävle, Department of Technology and Built Environment, 2009. http://urn.kb.se/resolve?urn=urn:nbn:se:hig:diva-4879.
Full textn today's complex environment, clear and sustainable energy is needed to support society development. How to develop the sustainable energy is a core issue in China. Compared with traditional energy, Wind energy has many advantages such as non-fuel cost, less pollution. And wind energy has the absolute advantage that it is worldwide available. In many courtiers, wind energy has become a major part of their plans for sustainable development. The primary goal of this paper is to analysis advantages and disadvantages of wind power in China and the development potential of wind power in China. In this paper the main methodology is using the information about wind power in China, which is including current situation, development stage, industry development stage, and combining the real case to analysis wind power development potential in China. There are six parts of this paper which are the overview of wind power in china; case description, analysis, conclusions, suggestion, development perspectives and imagination In the first part, the overview of wind power in china, the history of wind power in china, wind resource distribution, wind power development stages, the situation of some key regions, wind power industry develop stage and also some policies about wind power of Chinese government are discussed. The goal of this part is giving some fundamental information about wind power in China. In the second part, a real case has been described, and according to this case, the construction cost of a wind power plant in China has been discussed. The advantages and disadvantages of wind power are also analyzed based on this case study, such as long-team return, environmental impact, and also some other problem analysis. After the analysis parts, there are the conclusion parts, those parts are about the development perspectives and imagination of wind power in China.
Zaar, Emil. "Photovoltaic power potential on Gotland: A comparison with load, wind power and power export possibilities." Thesis, Uppsala universitet, Institutionen för geovetenskaper, 2016. http://urn.kb.se/resolve?urn=urn:nbn:se:uu:diva-295997.
Full textSrirattana, Nuttapong. "High-Efficiency Linear RF Power Amplifiers Development." Diss., Georgia Institute of Technology, 2005. http://hdl.handle.net/1853/6899.
Full textZhang, Meishenglan. "Power-Aware Software Development For EMCA DSP." Thesis, KTH, Skolan för informations- och kommunikationsteknik (ICT), 2017. http://urn.kb.se/resolve?urn=urn:nbn:se:kth:diva-215711.
Full textSmith, Cheryl Lynne. "The power of coaching in staff development." Thesis, National Library of Canada = Bibliothèque nationale du Canada, 2001. http://www.collectionscanada.ca/obj/s4/f2/dsk3/ftp04/MQ59481.pdf.
Full textEhlers, Bodo. "Development of high power diode laser systems /." Aachen : Shaker, 2005. http://bvbr.bib-bvb.de:8991/F?func=service&doc_library=BVB01&doc_number=014901694&line_number=0001&func_code=DB_RECORDS&service_type=MEDIA.
Full textTappin, Peter G. R. "Design and development of SIC power devices." Thesis, University of Newcastle Upon Tyne, 2008. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.514463.
Full textKong, Fei. "Development of series connected photovoltaic power inverter." Thesis, University of Cambridge, 2011. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.609938.
Full textKamanzi, Janvier. "Thermal electric solar power conversion panel development." Thesis, Cape Peninsula University of Technology, 2017. http://hdl.handle.net/20.500.11838/2527.
Full textThe world has been experiencing energy-related problems following pressuring energy demands which go along with the global economy growth. These problems can be phrased in three paradoxical statements: Firstly, in spite of a massive and costless solar energy, global unprecedented energy crisis has prevailed, resulting in skyrocketing costs. Secondly, though the sun releases a clean energy, yet conventional plants are mainly being run on unclean energy sources despite their part in the climate changes and global warming. Thirdly, while a negligible percentage of the solar energy is used for power generation purposes, it is not optimally exploited since more than its half is wasted in the form of heat which contributes to lowering efficiency of solar cells and causes their premature degradation and anticipated ageing. The research is geared at addressing the issue related to unsatisfactory efficiencies and anticipated ageing of solar modules. The methodology adopted to achieve the research aim consisted of a literature survey which in turn inspired the devising of a high-efficiency novel thermal electric solar power panel. Through an in-depth overview, the literature survey outlined the rationale of the research interest, factors affecting the performance of PVs as well as existing strategies towards addressing spotted shortcomings. While photovoltaic (PV) panels could be identified as the most reliable platform for sunlight-to-electricity conversion, they exhibit a shortcoming in terms of following the sun so as to maximize exposure to sunlight which negatively affects PVs’ efficiencies in one hand. On the other hand, the inability of solar cells to reflect the unusable heat energy present in the sunlight poses as a lifespan threat. Strategies and techniques in place to track the sun and keep PVs in nominal operational temperatures were therefore reviewed.
Jagasivamani, Meenatchi. "Development of a Low-Power SRAM Compiler." Thesis, Virginia Tech, 2000. http://hdl.handle.net/10919/34963.
Full textMaster of Science
Zhou, Renjie. "DEVELOPMENT OF HIGH POWER FIBER LASER TECHNOLOGIES." University of Dayton / OhioLINK, 2010. http://rave.ohiolink.edu/etdc/view?acc_num=dayton1271970621.
Full textJiang, Yimin. "Development of advanced power factor correction techniques." Diss., Virginia Polytechnic Institute and State University, 1994. http://hdl.handle.net/10919/53609.
Full textPh. D.
Grillos, Tara. "Participation, Power and Preferences in International Development." Thesis, Harvard University, 2015. http://nrs.harvard.edu/urn-3:HUL.InstRepos:23845452.
Full textPublic Policy
Sweetingham, Sarah. "Power and social justice in community development: Improving 'government towards development'." Thesis, Sweetingham, Sarah (2014) Power and social justice in community development: Improving 'government towards development'. Masters by Coursework thesis, Murdoch University, 2014. https://researchrepository.murdoch.edu.au/id/eprint/24865/.
Full textStone, Michael H., William A. Sands, Kyle C. Pierce, Michael W. Ramsey, and G. Gregory Haff. "Power and Power Potentiation among Strength-Power Athletes: Preliminary Study." Digital Commons @ East Tennessee State University, 2008. https://dc.etsu.edu/etsu-works/4138.
Full textTreasure, Karen. "The power of empowerment : recognising power relations within 'development' for communities in Zambia." Thesis, University of Plymouth, 2009. http://hdl.handle.net/10026.1/1144.
Full textElamin, Abdallah E. M. M. "Strategy development processes in selected Sudanese enterprises." Thesis, Lancaster University, 2001. http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.288980.
Full textLamoreux, Thomas Edward. "Competitive development economic development and the inquiry into power relations in Missouri /." Diss., Columbia, Mo. : University of Missouri-Columbia, 2006. http://hdl.handle.net/10355/4529.
Full textThe entire dissertation/thesis text is included in the research.pdf file; the official abstract appears in the short.pdf file (which also appears in the research.pdf); a non-technical general description, or public abstract, appears in the public.pdf file. Title from title screen of research.pdf file viewed on (June 26, 2007) Includes bibliographical references.
Huang, Yan. "FAST RECONFIGURATION ALGORITHM DEVELOPMENT FOR SHIPBOARD POWER SYSTEMS." MSSTATE, 2005. http://sun.library.msstate.edu/ETD-db/theses/available/etd-11012005-151018/.
Full textRussamee, Nilaped. "Development of a high power RF measurement system." Thesis, Cardiff University, 2012. http://orca.cf.ac.uk/48483/.
Full textNarayanaswamy, Lata. "Gender, power and the knowledge-for-development agenda." Thesis, Durham University, 2010. http://etheses.dur.ac.uk/530/.
Full textCornejo, Gómez César Alberto. "Methodology for the development of hydroelectric power plants." Thesis, Massachusetts Institute of Technology, 2016. http://hdl.handle.net/1721.1/107592.
Full textCataloged from PDF version of thesis.
Includes bibliographical references (pages 73-75).
Hydropower has sufficient resources available and is actively promoted by Governments as part of their energy matrix, but its development is constrained by the difficulty of addressing location particularities, including technical features such as geology or hydrology, and institutional features such as social acceptance, environmental constraints and the regulatory framework. Project results emerge from the interactions of these Inherent Features and the Project Architecture and do not always meet stakeholders' expectations, leading to deficient project results and lost value. This thesis proposes a methodology for prototyping projects to reflect these particularities and inform project shaping and decision-making early in the process. The proposed methodology was built on three systems engineering and project complexity frameworks, and lessons learned from four case studies. Its contribution to hydropower development is related to (i) the incorporation of systems evolution over time on the development process, (ii) the identification and management of relationships among the various decomposed elements of the development, (iii) the identification of emergent properties from the interactions among all features, (iv) a prototype for developers to optimize or search for project architectures that meet stakeholders objectives while complying with restrictions, (v) the delivery of unbiased information for decision-makers, (vi) the opportunity of stakeholders to participate in the project shaping in a continuous fashion, and (vii) the delivery of a tool for the implementation team to evaluate and challenge changes to the project during construction. The usage of this methodology does not guarantee the avoidance of errors or unforeseen project outcomes, but it does reduce the chance for unknown risks emerging from the interactions of the evaluated features.
by César Alberto Cornejo Gómez.
S.M. in Engineering and Management
Erol, Umit Levent. "DEVELOPMENT OF A LOWER EXTREMITY EXOSKELETON POWER UNIT." Case Western Reserve University School of Graduate Studies / OhioLINK, 2011. http://rave.ohiolink.edu/etdc/view?acc_num=case1619385500249639.
Full textChard, Simon Peter. "Development of versatile high power bounce geometry lasers." Thesis, Imperial College London, 2010. http://hdl.handle.net/10044/1/6184.
Full textAdams, Barbara Miller. "Owning professional development the power of teacher research /." [Ames, Iowa : Iowa State University], 2009.
Find full textWu, Guo-Jung, and 吳國榮. "Development of Electronic Power Meters with Reactive Power Measurement." Thesis, 2014. http://ndltd.ncl.edu.tw/handle/ve6mv4.
Full text國立臺北科技大學
自動化科技研究所
102
Due to global warming and shortage of energy, the idea of saving energy gradually attracts public’s attention. How to use and save energy efficiently has become an issue worthy of discussion. Therefore, to change the habit of using resources every day, the key is obtain the data usage of these resources first before it can be improved. Advanced Metering Infrastructure (Advanced Metering Infrastructure, AMI) in this case plays a crucial role, and "Intelligent Power meter" is the core to establish "advanced metering system". This paper utilizes MSP430AFE253 processor as the core element for the development of electronic watt-hour meters. This MCU is specifically designed for single-phase electronic watt-hour meters. It has internal analog front-end circuit that can handle AC signals. The MCU has three 24-bit delta-sigma ADCs that is capable of acquiring single-phase voltages and currents simultaneously and it has an additional PGA (Programmable Gain Amplifier) function. The MCU calculates the necessary information, such as Vrms, Irms, KW, KVAR, KVA, PF, etc. after the signals are acquired. In addition, the development of electronic watt-hour meters have communication capabilities. Such functions help to send the data on electric consumption from users back to control center and meter calibration procedures, making electronic digital meter meets the standard error range. If the Intelligent Power Meters provide reactive power information, users can then improve the power factor of the load, reducing line losses. Therefore, this paper uses digital Finite Impulse Response filter (Finite Impulse Response, FIR), response filter (First-FIR, filter) and the translation method through a first-order finite impulse to complete the reactive power calculations.
Huang, Chung-che, and 黃崇哲. "Development of Power Converters for Small Wind Power Systems." Thesis, 2010. http://ndltd.ncl.edu.tw/handle/95723632840281483211.
Full text國立臺灣科技大學
電機工程系
98
This thesis presents the analysis and design of power converters for wind generators. The system can transfer the generator power from varying-voltage and varying-frequency to 60 Hz single-phase source. The system uses ac-dc power converter to serve as the generator side power converter. When the wind speed is low, the ac-dc power converter uses cascade boost structure to raise the dc-link voltage. When the wind speed is nominal, the ac-dc power converter uses boost structure. Whereas, when the wind speed is high, the ac-dc power converter uses full-bridge rectifiers to keep dc-link voltage lying within the constant range. A buck/boost dc chopper is designed to charge and discharge batteries in order to regulate the power flow between renewable energy and system loads so that it can supply stable dc power to system loads. The single-phase full-bridge inverter designed can not only control the output voltage but also operate in either stand-alone or grid-connected fashion. A high-performance and low-cost digital signal processor TMS320F2808 is used to implement the control function to control the power converters. An experimental system is built. The system can provide single-phase AC 110V to single-phase load under stand-alone operation mode. The output of the effective power is 345W. Under grid-connected mode, the power converter supplies 235W with the corresponding efficiency of 79.6% using cascade boost topology. Finally, experimental results are given to justify the analysis.
Pan, Yu-hsin, and 潘郁昕. "Development of Power Converters for Solar Power Conversion Systems." Thesis, 2009. http://ndltd.ncl.edu.tw/handle/91398572127818786305.
Full text國立臺灣科技大學
電機工程系
97
This thesis presents the development of a solar power generating system. The solar-cell system uses boosted dc-dc power converter and maximum power point tracking. They are designed to enhance conversion efficiency and achieve high power output. It can be applied to different solar-cell systems by different voltages with two parallel dc-dc converters. Using perturbation and observation method, a maximum power point tracking controller, the solar-cell can achieve maximum power control in accordance with illumination. The single phase full-bridge dc-ac converter uses unipolar voltage switching method on power grid side. It can convert dc-source to single-phase current output with constant voltage and constant frequency. This system can receive feedback voltage to adjust output voltage. It can keep output voltage constant under load is variation. In current mode, it can support stable single phase current and connect with power grid. In this thesis, a high-performance, low-cost digital signal processor TMS320LF2812 is used to implement the system for reducing the circuit components and cost. A prototype of 800W hybrid power conversion system is developed. The system can feed proper power to the grid in grid-connected operation. While for stand-alone operation, the rated output voltage is 110V and the frequency is 60 Hz. The efficiency of the whole system in grid-connected operation reaches 91%. The range of solar-cell voltage is between 100~180V. Experimental results are given to verify the proposed system.
洪若馨. "Development of a Simple Power Failure Retraction Development of a Simple Power Failure Retraction." Thesis, 2012. http://ndltd.ncl.edu.tw/handle/09964010298511683716.
Full text國立彰化師範大學
電機工程學系
100
In this thesis, a simple power-failure retraction equipment for cylindrical grinding machines is developed. It can make the grinding wheel be able to retract while the main power supply is failed for avoiding over-grinding the workpiece. Conventionally, an uninterrupted power system (UPS) is used to ensure the retraction of the grinding wheel. However, it will cost a lot because of the large power capacity requirement, up to tens of kVA. From the experimental results, it can be seen that by adopting proper capacitors the proposed simple equipment can provide more than 0.3mm retraction while the main power is failed. As a result, the proposed simple mechanism can be used to replace the large UPS and reduce 97.27% cost.
Wei-Chih, Yeh. "Development of Broadband Power Amplifiers." 2007. http://www.cetd.com.tw/ec/thesisdetail.aspx?etdun=U0001-1701200714161800.
Full textYeh, Wei-Chih, and 葉威志. "Development of Broadband Power Amplifiers." Thesis, 2007. http://ndltd.ncl.edu.tw/handle/84758192239282289005.
Full text國立臺灣大學
電子工程學研究所
95
According to some researches, no matter in the time domain or in the spatial domain, that the usage of spectrum with utilization ranging from 15% to 85% in the bands below 3 GHz. At frequency above 3 GHz the actual utilization is dramatically lower. The FCC has issued the Cognitive Radio System, this system can improve the utilization of spectrum without interfere with the users who have primary rights to use the spectrum by sensing and changing the transmitted band. In order to transmit signal in multiple frequency bands, there should be a broadband power amplifier in transmitter to adapt to this system. Circuit design and theory of RF power amplifier are the main research points of this thesis. We analyze some kinds of broadband power amplifier technique and finally we decided to design broadband power amplifier with network synthesis broadband matching. We use WIN GaAs PHEMT 0.15μm process to design broadband power amplifier. We cascade two common source amplifiers, and all matching networks are integrated into single chip. Operation frequency of this power amplifier is from 3GHz to 7.5GHz, power gain is from 19.6dB to 21.6dB, output P1dB is from 21.5dBm to 22.9dBm and PAE is from 19.5% to 29.5%.
HU, JHIH-HUEI, and 胡智惠. "Development of solar power system." Thesis, 2018. http://ndltd.ncl.edu.tw/handle/2yyqhu.
Full text聖約翰科技大學
電機工程系碩士在職專班
106
Electric energy is an important basis for the economic development of a country. It is also an essential energy source of human life. Effective use of solar power can prevent the waste of power resource and increase power supply quality. In micro-grids, accurate photovoltaic prediction has many benefits, like providing proper power scheduling, reducing operating costs even improving power supply reliability. The traditional solar photovoltaic forecasting method designs the prediction model by environmental information and solar photovoltaic module information. The relationship between these two data and the photovoltaic power generation amount is nonlinear. The traditional method is difficult to solve the nonlinear problems. This paper confirms the relationship between input parameters and output generation amount. By the correlation coefficients in the statistics, the relative influence of each parameter can be obtained. In the proposed forecast method, illumination is considered as one of the forecast data. However, if the illumination changes greatly, the fluctuation of power generation and the prediction error will greatly increase.
Liang, Zhong-Chen, and 梁宗正. "Development of Power Converter for Fuel Cell Power Conversion Systems." Thesis, 2009. http://ndltd.ncl.edu.tw/handle/89101798865127636914.
Full text國立臺灣科技大學
電機工程系
97
This thesis is concerned with the analysis and implementation of parallel full-bridge dc-dc power converter and single-phase full-bridge dc-ac power converter. The full-bridge dc-dc power converter operates under voltage feedback control mode by using phase-shift control to convert fuel cell voltage source to high voltage. Under the full-bridge dc-dc power converters of parallel operations, using current-sharing strategies will increase capacity and utilization rate of the systems and accomplish load-sharing. The master-slave control technique is used in order to increase the reliability of the system. To achieve low harmonic distortion and fast response, the single-phase full-bridge power converter adopts sinusoidal pulse-width modulation (SPWM) unipolar switching technique. The single-phase full-bridge power converter can provide constant and stable output voltage under load variation by using amplitude-locked loop algorithm of voltage-controlled mode, and stable single-phase current to power grid under current-controlled mode. In this system, a high-speed, low-cost digital signal processor TMS320LF2812 is used to host the control system. The voltage and current control rules are realized by software. It can not only reduce the hardware cost but also improve the system reliability. The experimental results with linear load of 600 W show that the single-phase output voltage is 110 V, 60 Hz. The total harmonic distortion of output voltage is 4.67 %, the efficiency of the system reaches 80 %. Besides, the system can feed real power to the grid in grid-connected operation. Experimental results are given to justify the analysis.
Ji, Hong, and 季宏. "Development and Application of the High Power Planetary Power Generator." Thesis, 2011. http://ndltd.ncl.edu.tw/handle/24698828914753109009.
Full text崑山科技大學
光電工程研究所
99
The size of the output voltage of traditional power generators depend on the magnetic flux changes in the induction coil over an amount of time, so in order to increase the output voltage one needs to increase the size of the magnetic field, the number of induction coils, add silicon steels, and install gear boxes..etc. However, these methods will cause the rotor weight to increase, resulting in a magnetic pull, thereby increasing the generator bearing load which makes the rotor harder to run, making it a bad choice to use clean energy as its driving source. Therefore how to improve traditional power generating devices is the purpose of this research. This thesis report introduces a newly developed “Planet Style Power Generator”, and applies this generator on a variety of devices. Based on actual testing results using the device on HPEG, the maximum output of the developed HPEG can reach 300W, with the output current being 1.2~1.3A. Using the device on an emergency back up power generator, the maximum output power could reach up to 46W, with a maximum output current of 0.38A.Used on Planetary axial flux a single-phase AC power permanent magnet generator, the greatest successful output is about 410W when the rotating speed reaches the maximum 200 rpm.
Floyd, Michael Cameron Dawley. "Development of Ferromagnetic Metallic Glasses into Low Loss Power Transformer Cores." Thesis, 2018. https://thesis.library.caltech.edu/10546/13/development-ferromagnetic-metallic.pdf.
Full textCurrently, 3% of energy losses in the U.S. electrical grid occur at power transformers. With a transition to Metglas, transformer efficiency could be increased, but is Metglas the best replacement material for power transformers?
With this in mind we develop a Fe-based metallic glass for its glass forming ability and soft magnetic properties. During this development we identify a redox reaction of boron oxide by Si during melt fluxing of the Fe-based glass, which promotes an unexpected exchange of Si and B in the alloy. Taking this reaction into account, a unique optimization strategy is implemented, enabling oxide purification of the melt coupled with a significant but predictable shift in composition. This leads to an optimized Fe-based glass demonstrating a global peak in glass forming ability. Following boron oxide fluxing in the high temperature melt, alloy with composition Fe57.5Co20.2Si10.2B2.05P10.05 transforms to Fe57Co19.2Si6.8B7.4P9.6, and increases its critical rod diameter from 1 mm to 5 mm. The alloy also demonstrates excellent soft ferromagnetic performance characterized by a magnetic saturation of 1.53 T.
While developing the above alloy, we also analyzed the effect of varying thickness of a Fe68Mo4Ni3Co5Si1P11.5C5B2.5 transformer core as a function of frequency to discover if there was a minimum in the losses. We did not find a single minimum, but found that the optimal thickness exhibits a logarithmic dependency on frequency. This dependence suggests the optimal thickness of a core ranges from 100−400μm, instead of in the < 50μm range currently used. These larger optimal thicknesses are unexpected if anomalous losses are not considered, but the dominance of the anomalous losses at low frequencies, or for thin samples, validates the need for thicker power transformers. While other amorphous metals and casting techniques will yield varying results, the logarithmic dependence on frequency and the 100−400μm optimal thickness range should be broadly applicable.
zhan, zhi-sheng, and 詹志勝. "Development of A Power Harmonic Analyzer." Thesis, 2010. http://ndltd.ncl.edu.tw/handle/99217548280232977560.
Full text國立臺灣科技大學
電機工程系
98
The goal of this thesis is to design and implement a power analyzer, in which practicality, immunity and precision are under considered. A high-performance digital-signal-processor (DSP) is employed as the core of the analyzer which provides real-time calculation for all available measurement functions. Three channels of voltage and three channels of current are sensered through the potential transformers (PT) and current transformers (CT) and are converted by six individual angalog-to-digital converters, which provides 16-bit resolution. An averaging procession is used to obtain precise results. For each input channel, four cycles of the signal are obtained from 1024 data points and the Hanning window is used to implement haracterization on the spectrum for avoiding spectral leakage. Some special instructions are used to execute the complex fast Fourier transform for analyzing the measured signals. Finally, all available sesults are sent to a seperated digital processor for display or futher processing.
LIN, Jun-Tsun, and 林俊村. "Development of a Hybrid Power Scooter." Thesis, 2007. http://ndltd.ncl.edu.tw/handle/39626634841271382270.
Full text國立屏東科技大學
車輛工程系所
95
This thesis is aimed to develop an ICE-electric hybrid-power scooter which uses a 900W hub motor to provide a small rate of assistant power to a scooter originally equipped with a 125cc fuel injection ICE. The work is divided into two parts, namely, hardware design and software design. For the work of hardware design, a X-by-wire throttle valve, a generator mount mechanism, a hub mount mechanism, and the circuits for control of all the subsystem were design and implemented under the constraints of the physical space of the scooter. As to the work of the software design, a lookup table based as well as a fuzzy logic energy management strategy have been proposed. Performance evaluation experiments have been carried out the developed system under a series of road tests. The test results show that the designed system can lower a fuel consumption rate of 40% with the battery SOC staying above 70%.
Chang, Tse-Yung, and 張澤湧. "Development of Power-Assisted Transport Wheelchair." Thesis, 2013. http://ndltd.ncl.edu.tw/handle/73538796463201921348.
Full text國立陽明大學
物理治療暨輔助科技學系
101
Wheelchairs are very helpful for people who have brain, nerves and degenerative disease or lower limb disorders. Among these groups, most of them can’t control wheelchairs or electric ones, as a result, they need caregivers’ help to handle them. Furthermore, because of the general type wheelchairs are unpowered, the caregivers have to overcome the long-distance walk or the rough roads, and therefore causes inconvenience or difficulty. In addition, with advances in technology, population ageing and the low birth rate is expected to lead to a burgeoning demand for aged care services. In consequence, it is important to provide power-assisted wheelchairs. The development of electric powered wheelchairs has gradually progressed, and there are many functional electric powered wheelchairs on the market. Most electric powered wheelchairs’ use is designed for disabled users themselves, and not for the caregivers’ assistance. Although some control interfaces design for caregivers, the settings of them are not suited for them. The specific aim of this study is to design a power-assisted wheelchair for caregivers. This device can be easily controlled without learning. It can be used in a variety of contexts (asphalt, grass, uphill, downhill, outdoor environment) without wearing any sensors. In this study, we detected the location of the caregiver to control the wheelchair to move forward and backward. The results showed that the distance between the caregiver and power assisted wheelchair maintained at 45-65 cm when moving forward while 60-80 cm were observed when moving backward. In addition, without the use of our device, the thrust test in a variety of contexts (asphalt, grass, uphill, downhill, outdoor environment) was significantly lower. The support test showed that the device can provide 180 to 200N support when the users were in need of help. Only by understanding the users' actual usage can we improve the actual test. In the near future, the improvement of the power-assisted wheelchair might be advantage to the caregivers.
Tsai, Chin-Wei, and 蔡智偉. "Development of RF CMOS Power Amplifier." Thesis, 2006. http://ndltd.ncl.edu.tw/handle/r8aca6.
Full text國立臺北科技大學
自動化科技研究所
94
This thesis presents the development of RF CMOS power amplifier which is implemented by UMC CMOS 0.18-um 1P6M process. A class E power amplifier and a cascode power amplifier are designed to be used in bluetooth system and wireless sensor network system, respectively. In the matching network design, the input matching network is designed for maximum gain transducer by conjugate matching and the output matching is designed for maximum power transducer by load-pull matching. The simulation results of class E power amplifier whose input matching network and output matching network are on the chip and off the chip respectively are output power of 21.214dBm, PAE of 37.765% and power gain of 17.214dB at 2.4GHz. And the cascade power amplifier which is a fully chip realized an overall PAE of 20% with output power of 3.583dBm and had power gain of 7.583dB at 2.4GHz. In general, the effect of layout is not considered in the simulation of circuit level. This thesis considers the parasitic effect after layout to obtain more accurate results of simulation.
Lin, Jhan-Jia, and 林斬嘉. "Development of Solar Light Power Estimator." Thesis, 2013. http://ndltd.ncl.edu.tw/handle/bf33na.
Full text國立虎尾科技大學
電機工程研究所
101
This thesis uses five photo diodes as sunlight detectors to implement sunlight measurement system, the photo diodes are located on five facets which on the front, rear, left, right and horizontal, individually, of constituting a light measuring sensor and the associate azimuth angle and altitude angle can be found throughout perpetual calendar. Direct Solar Radiation of each sunlight detector can be estimated by the equation derived from the minimum angle of incidence. Sunlight measurement system in this thesis is placed horizontally to detect the optical power from all detectors, by using principle of vectors geometrical space and coordinate transformation to indicate the real time solar power. By comparing the differences between measurement results and experimental results, both theory of value and actual value are consistency, therefore, the proposed solar light sensor system is capable to measure precisely.
Chang, Feng-Ying, and 張豐瀅. "Development of Solar Light Power Detector." Thesis, 2013. http://ndltd.ncl.edu.tw/handle/6j284s.
Full text國立虎尾科技大學
電機工程研究所
101
In this thesis, the photo diode detectors are used to realize the solar light sensor for measuring the relative solar orientations and solar energy. The sunlight measurement detector in this study is the combination of the conical sensor and the cubic sensor, delicately designed to measure the light energy. Accordingly, the photo detectors located on five facets can detect solar light from various directions and measure the incident solar energy. Based on the geometric space transformation principle, the relationship equation between measured power of various-facet detectors and solar lighting source can be conducted. The solar power can be precisely extrapolated without using any electronic compass and extra orientation angle corrector.