Dissertations / Theses on the topic 'Bulk charge transport'

In this Ph.D. work, we investigate the optoelectronic properties of low-bandgap semiconducting polymers and project the potential for employing these materials in electronic and photonics devices, with a particular emphasis on use in organic solar cells. The field of organic solar cells is well developed and many of the fundamental aspects of device operation and material requirements have been established. However, there is still more work to be done in order for these devices to ultimately reach their full potential and achieve commercialization. Of immediate concern is the low power conversion efficiency demonstrated in these devices so far. In order to improve upon this efficiency, several routes are being explored. Because the optical bandgaps of semiconducting polymers are larger than in inorganic semiconductors, one of the most promising routes currently under exploration is the development of low-bandgap materials. Using polymers with lower band gaps will allow more of the solar irradiance spectrum to be absorbed and converted into electricity and thus possibly boost the overall efficiency. The bandgap of these semiconducting polymers is determined by the chemical structure, and therefore can be tailored through synthesis if the relevant structure-property relationships are well-understood. The materials studied in this work, a new series of Poly(thienylenevinylene) (PTV) derivatives, posses lower band gaps than conventional polymers through a design that incorporates aromatic-quinoid structural disturbances. This type of chemical structure delocalizes the electronic structure along the polymer backbone and reduces the energy of the lowest excited-state leading to a smaller band-gap. We investigate these materials through a variety of techniques including linear spectroscopy such as absorption and photoluminescence, pump-probe techniques like cw-photoinduced absorption and transient photo-induced absorption, and the non-linear electroasborption technique in order to interrogate the consequences of the delocalized electronic structure and its response to optical stimuli. We additionally consider the effects of environmental factors such as temperature, solvents and chemical doping agents. During the course of these investigations, we consider both of the two primary categorical descriptions of structure-property relationships for polymers within the molecular exciton model, namely the role of inter-molecular interactions on the electronic properties through the variation of supermolecular order and the fundamental determination of electronic structure due to specific intra-molecular interaction along the backbone of the polymer chain. We show that the dilution of aromaticity in semiconducting polymers, while being a viable means of reducing the optical band gap, results in a significant increase in the role of electron-electron interactions in determining the electronic properties. This is observed to be detrimental for device performance as the highly polarizable excited state common to polymers gives way to highly correlated state that extinguishes both the emissive properties and more importantly for solar cells, the charge-generating characteristics. This situation is shown to be predominant regardless of the nature of interchain interactions. We therefore show that the method of obtaining low-bandgap polymers here comes along with costly side-effects that inhibit their efficient application in solar cells. Further, we directly probe the efficacy of these materials in the common bulk-heterojunction architecture with both spectroscopy and device characterization in order to determine the limiting and beneficial factors. We show that, while from the point of view of absorption of solar radiation these low-bandgap polymers are more suited for solar cells, the ability to convert the absorbed photons into electron-hole pairs and generate electricity is lacking, due to the internal conversion into the highly correlated state and thus, the absorbed photon energy is lost. For completeness, we fabricate devices and verify that both the charge-transport properties and alignment of charge extraction levels with those of the contacts can not be responsible for the dramatic decrease in efficiency found from these devices as compared to other higher band gap polymers. We thus conclusively determine that the lack of power converison efficiency is governed by the inefficiency of charge-generation resulting from the intrinsic defective molecular structures rendering a low-lying optically forbidden state below the lowest optical allowed state that consumes the majority of the photogenerated excitons. It is emphasized that our means of investigation allow us to truly access the potential of these materials. In contrast, the direct application of these systems in devices and interpretation of the performance is exceedingly complex and may obscure their true potential. In other words, poor performance from a device may be extrinsic in nature and the optimization process may be very costly with respect to both time and materials. The methods used here however, allow us to determine the intrinsic potential. Not only is this beneficial in terms of preserving the resources that would be used on the trial-and-error method for devices, but it also allows us to learn more on a fundamental level about the structure-property relationships and their implications for device performance. The benefits of this increased understanding are two-fold. First, by learning about the fundamental response of a material, a new application may be realized. For example, the rapidly efficient internal conversion process that renders the materials in this study as poor candidates for solar cells may make them useful for photonics applications, as optical switches, for instance. Secondly, this type of investigation has implications for the whole organic electronics community instead of just being limited to the particular material system and the primary application attempted. In this case, we are essentially able to determine a threshold for aromaticty necessary in a structure that will preserve the stability of the ionic excited state that is useful for charge generation in solar cells.

La conception de cellules solaires organiques de type hétérojonction en volume a été proposée pour la première fois en 1990. Ces dispositifs sont composés d’un mélange de polymères conjugués, donneurs d’électrons, et de fullerènes, accepteur d’électrons, et ont pour la première fois permis d’atteindre un rendement de conversion énergétique significatif (de l’ordre de 2%) avec des semi-conducteurs organiques. Dans ce contexte, cette thèse a porté sur l'étude approfondie d’une série de molécules donneurs d’électrons de forme d’haltère, dont le groupement planaire est l’unité triazatruxène (TAT) et le cœur déficient en électrons le thienopyrroledione (TPD). Les molécules de cette série se différencient par la nature des chaînes alkyles, attachées à l’unité centrale et aux unités TAT. Plus précisément, la relation entre la nature des chaînes latérales et les propriétés moléculaires et thermiques de ces molécules en forme d’haltère ont été étudiées en détail. L'impact des chaînes alkyles sur la morphologie en film mince à l’échelle nanométrique a également été étudié. Afin de mieux comprendre l’influence de la microstructure des films minces (constitués soit uniquement des molécules donneuses soit de mélanges molécules/fullerènes), le transport de charge dans le plan du film et perpendiculairement au plan ont été mesurées en fonction de la phase (amorphe, cristalline, …) du matériau. Des cellules solaires BHJ en mélange avec le dérivé de fullerène ont également été réalisées
The prospective conception of electron-donor/electron-acceptor (D/A) bulk heterojunction solar cells was first reported in 1990s, which blended the semiconducting polymer with fullerene derivatives, enhancing the power conversion efficiency. Since then, interests on this domain has been increasing continuously, and the efficiencies of BHJ solar cells have been increased dramatically. In this context, this thesis focuses on the study of a series of dumbbell-shaped small molecule donors, based on a highly planar unit called triazatruxene. The only difference between those molecules is the side-chains attached to central units and TAT units. As a consequence, the relationship between side chains nature and optoelectronic and structural properties of our TAT-based dumbbell-shaped molecular architecture will be investigated in detail. The impact of the alkyl chains on the molecular and thin film properties was also studied, with a particular emphasis put on microstructure and charge transport aspects. In-plane and out-of-plane charge carrier transport, with pure molecules and blend with fullerene, are measured in different systems. BHJ solar cells in blend with fullerene derivatives were also realized

Recent advancements in gate stack engineering has led to the development of aggressively scaled, high mobility, high-k dielectric based NMOSFETs with metal gates. Most of the current literature on the subject also stressed on the need for a high temperature process step to attain the high mobility under minimal change of effective oxide thickness. However, the physical origin of high mobility is not well understood. In this work, fundamental insight into the necessity of the high temperature process step is provided. Novel experimental strategies are developed to understand the impact of interface states and bulk traps separately and exclusively on channel mobility. It is conjectured that the interface states at the SiO2/(100) bulk-Si interface are identical in nature (as far as coupling with the channel electrons is concerned) to those at the high-k/SiO2/(100) bulk-Si interface. Thus, the response of interface states on channel electrons in high-k insulator based NMOSFETs is properly calibrated by a novel thermal desorption of hydrogen experiment on SiO2/(100) bulk-Si NMOSFETs to yield a highly accurate parameterized equation. The value of interface state response parameter determined by the aforementioned experiment is compared with theoretical predictions, and independently determined projections from electrical stress measurements. The impact of transient charging on transport in the channel is investigated. It is conclusively shown that remote charge has minimal impact on mobility in the channel. The role of nitrogen induced fixed oxide charge is studied on a set of Hf-silicate samples. Role of soft optical phonon scattering and the beneficial impact of metal gates on soft optical phonon limited mobility are thoroughly investigated both theoretically and experimentally. Conclusions are drawn on the fundamental limit of mobility attainable in high-k dielectric based NMOSFETs.

La structure chimique des semiconducteurs organiques utilisés dans les cellules photovoltaïques à base d’hétérojonction en volume peut fortement influencer les performances du dispositif final. Pour cette raison, une meilleure compréhension des relations structure-propriétés demeure cruciale pour l’amélioration des performances. Dans ce contexte, cette thèse fait état d'études approfondies du transport des charges, de la morphologie et des propriétés photovoltaïques sur de nouveaux copolymères à faible bande interdite. En premier lieu, l'impact de la position des chaînes alkyles sur les propriétés opto-électroniques et morphologiques a été étudié sur une famille de polymères. Les mesures du transport de charges ont montré que la planéité du squelette du copolymère influe sur l’évolution de la mobilité des charges avec la concentration de porteurs libres. Ce comportement suggère que le désordre énergétique électronique est fortement impacté par les angles de torsion intramoléculaire le long de la chaîne conjuguée. Un second copolymère à base d'unités accepteur de [2,1,3] thiadiazole pyridique, dont les niveaux d’énergie des orbitales frontières sont optimales pour l’application photovoltaïque, a ensuite été étudié. Les performances obtenues en cellule photovoltaïque sont très inférieures aux attentes. Des analyses de la morphologie et du transport de charge ont révélé que l’orientation des lamelles cristallines est défavorable au transport perpendiculaire au film organique et empêche ainsi une bonne extraction des charges photo-générées. Enfin, les propriétés opto-électroniques et photovoltaïques de copolymères fluorés ont été étudiées. Dans ce cas, les atomes de fluor favorisent la formation de lamelles orientées favorablement pour le transport. Ces bonnes propriétés nous ont permis d'atteindre un rendement de conversion de puissance de 9,8% avec une simple hétérojonction polymère:fullerène
The chemical structure of organic semiconductors that are utilized in bulk heterojunction photovoltaic cells may strongly influence the final device performances. Thus, better understanding the structure-property relationships still remains a major task towards high efficiency. Within this framework, this thesis reports in-depth material investigations including charge transport, morphology and photovoltaic studies on various novel low band-gap copolymers. First, the impact of alkyl side chains on the opto-electronic and morphological properties has been studied on a series of polymers. Detailed charge transport investigations showed that a planar conjugated polymer backbone leads to a weak dependence of the charge carrier mobility on the carrier concentration. This observation points out that the intra-molecular torsion angle contributes significantly to the electronic energy disorder. Solar cells using another novel copolymer based on pyridal[2,1,3]thiadiazole acceptor unit have been studied in detail next. Despite the almost ideal frontier molecular orbital energy levels, this copolymer did not perform in solar cells as good as expected. A combined investigation of the thin film microstructure and transport properties showed that the polymers self-assemble into a lamellar structure with polymer chains being oriented preferentially “edge-on”, thus hindering the out-of-plane hole transport and leading to poor charge extraction. Finally, the impact of fluorine atoms in fluorinated polymers on the opto-electronic and photovoltaic properties has been investigated. In this case, the presence of both flat-lying and standing lamellae enabled efficient charge transport in all three directions. As a consequence, good charge extraction was possible and allowed us to achieve a maximum power conversion efficiency of 9.8%

Organic solar cells have great potential for cost-effective and large area electricity production, but their applicability is limited by the relatively low efficiency. In this dissertation I report investigations of novel materials and the underlying principles of organic solar cells, carried out at the University of St Andrews between 2011 and 2015. Key results of this investigation: • The charge carrier mobility of organic semiconductors in the active layer of polymer solar cells has a rather small influence on the power conversion efficiency. Cooling solar cells of the polymer:fullerene blend PTB7:PC₇₁BM from room temperature to 77 K decreased the hole mobility by a factor of thousand but the device efficiency only halved. • Subphthalocyanine molecules, which are commonly used as electron donor materials in vacuum-deposited active layers of organic solar cells, can, by a slight structural modification, also be used as efficient electron acceptor materials in solution-deposited active layers. Additionally these acceptors offer, compared to standard fullerene acceptors,advantages of a stronger light absorption at the peak of the solar spectrum. • A low band-gap polymer donor material requires a careful selection of the acceptor material in order to achieve efficient charge separation and a maximum open circuit voltage. • Metal structures in nanometer-size can efficiently enhance the electric field and light absorption in organic semiconductors by plasmonic resonance. The fluorescence of a P3HT polymer film above silver nanowires, separated by PEDOT:PSS, increased by factor of two. This could be clearly assigned to an enhanced absorption as the radiative transition of P3HT was identical beside the nanowires. • The use of a processing additive in the casting solution for the active layer of organic solar cells of PTB7:PC₇₁BM strongly influences the morphology, which leads not only to an optimum of charge separation but also to optimal charge collection.

Organic photovoltaic (OPV) is an exciting energy harvesting technique. Although its power conversion efficiency (PCE) now exceeds 10% in a research laboratory, the processing window of an OPV cell is still narrow. A fundamental understanding of the OPV materials is desired. This thesis presents the charge carrier transport properties and electronic interactions in the bulk heterojunction (BHJ) active layer of OPV cells. They were found to be well correlated with OPV device performances. Space-charge-limited current (SCLC) measurements and admittance spectroscopy (AS) were employed to study the charge transports, while photothermal deflection spectroscopy (PDS) was used to probe the trap densities inside the materials. Beneficial effects of a common solvent additive, 1,8-diiodooctance (DIO), on PTB7:PC71BM OPV cells have been investigated. With DIO present in the casting solution, the resulting BHJ films have much enhanced electron mobilities, whereas the impact on the hole mobility is negligible. The origin of increased electron mobility is the reduced average electron hopping distance for those films prepared with DIO solvent additive. A balance of hole-electron mobility by tuning the DIO concentration was demonstrated to be the way to optimize the OPV device performance. In light of carrier transport measurement results, a "polymer-rich" strategy with preserved device performance was demonstrated. After understanding the importance of balanced hole-electron mobility, the impact of donor-acceptor weight ratio on the performance of PTB7 : PC71BM based OPV cells was explored. Early stage electronic donor-acceptor interactions were revealed using ultra-low dosages of fullerenes. Before electron transport pathways percolate, the unconnected fullerene domains act as traps and hinder electron transport. From PDS, the trap density observed inside BHJ films was found to be anti-correlated with the fill factor of OPV devices. The origin of low FFs is mainly due to electron traps and localized states from fullerenes. Based on the observations, it is proposed that PC71BM tends to intercalate with PTB7 backbone instead of forming self-aggregates before the electron pathway percolation. Apart from investigating the fundamentals in OPV devices, a solution to improve its processing window was proposed in this thesis. Thermally stable polymer : fullerene OPV cells were fabricated by employing fluorenone-based solid additives. A charge transfer interaction between the additives and donor moiety of polymer formed a locked network which freezes the BHJ morphology under thermal stress. The most promising result retains 90% of the origin efficiency, upon thermal aging at 100 °C for more than 20 hours in PTB7:PC71BM solar cells. Besides fullerene-based OPV, all-polymer photovoltaic solar cells (all-PSCs) were also investigated. Two new difluorobenzene-naphthalene diimide based polymer electron acceptors, one random (P1) and one regioregular (P2) structure, were compared. P2 exhibited a much better molecular packing, a higher electron mobility and more balanced hole-electron mobilities in its composite film with polymer donor, PTB7-Th. An optimized PTB7-Th:P2 device can achieve a respectably high PCE over 5% for all-PSC devices. These all-PSCs should open a new avenue for next generation OPVs.

Organic semiconductors are a new key technology for large-area and flexible thin-film electronics. They are deposited as thin films (sub-nanometer to micrometer) on large-area substrates. The technologically most advanced applications are organic light emitting diodes (OLEDs) and organic photovoltaics (OPV). For the improvement of performance and efficiency, correct modeling of the electronic processes in the devices is essential. Reliable characterization and validation of the electronic properties of the materials is simultaneously required for the successful optimization of devices. Furthermore, understanding the relations between material structures and their key characteristics opens the path for innovative material and device design. In this thesis, two material characterization methods are developed, respectively refined and applied: a novel technique for measuring the charge carrier mobility μ and a way to determine the ionization energy IE or the electron affinity EA of an organic semiconductor. For the mobility measurements, a new evaluation approach for space-charge limited current (SCLC) measurements in single carrier devices is developed. It is based on a layer thickness variation of the material under investigation. In the \"potential mapping\" (POEM) approach, the voltage as a function of the device thickness V(d) at a given current density is shown to coincide with the spatial distribution of the electric potential V(x) in the thickest device. On this basis, the mobility is directly obtained as function of the electric field F and the charge carrier density n. The evaluation is model-free, i.e. a model for μ(F, n) to fit the measurement data is not required, and the measurement is independent of a possible injection barrier or potential drop at non-optimal contacts. The obtained μ(F, n) function describes the effective average mobility of free and trapped charge carriers. This approach realistically describes charge transport in energetically disordered materials, where a clear differentiation between trapped and free charges is impossible or arbitrary. The measurement of IE and EA is performed by characterizing solar cells at varying temperature T. In suitably designed devices based on a bulk heterojunction (BHJ), the open-circuit voltage Voc is a linear function of T with negative slope in the whole measured range down to 180K. The extrapolation to temperature zero V0 = Voc(T → 0K) is confirmed to equal the effective gap Egeff, i.e. the difference between the EA of the acceptor and the IE of the donor. The successive variation of different components of the devices and testing their influence on V0 verifies the relation V0 = Egeff. On this basis, the IE or EA of a material can be determined in a BHJ with a material where the complementary value is known. The measurement is applied to a number of material combinations, confirming, refining, and complementing previously reported values from ultraviolet photo electron spectroscopy (UPS) and inverse photo electron spectroscopy (IPES). These measurements are applied to small molecule organic semiconductors, including mixed layers. In blends of zinc-phthalocyanine (ZnPc) and C60, the hole mobility is found to be thermally and field activated, as well as increasing with charge density. Varying the mixing ratio, the hole mobility is found to increase with increasing ZnPc content, while the effective gap stays unchanged. A number of further materials and material blends are characterized with respect to hole and electron mobility and the effective gap, including highly diluted donor blends, which have been little investigated before. In all materials, a pronounced field activation of the mobility is observed. The results enable an improved detailed description of the working principle of organic solar cells and support the future design of highly efficient and optimized devices
Organische Halbleiter sind eine neue Schlüsseltechnologie für großflächige und flexible Dünnschichtelektronik. Sie werden als dünne Materialschichten (Sub-Nanometer bis Mikrometer) auf großflächige Substrate aufgebracht. Die technologisch am weitesten fortgeschrittenen Anwendungen sind organische Leuchtdioden (OLEDs) und organische Photovoltaik (OPV). Zur weiteren Steigerung von Leistungsfähigkeit und Effizienz ist die genaue Modellierung elektronischer Prozesse in den Bauteilen von grundlegender Bedeutung. Für die erfolgreiche Optimierung von Bauteilen ist eine zuverlässige Charakterisierung und Validierung der elektronischen Materialeigenschaften gleichermaßen erforderlich. Außerdem eröffnet das Verständnis der Zusammenhänge zwischen Materialstruktur und -eigenschaften einen Weg für innovative Material- und Bauteilentwicklung. Im Rahmen dieser Dissertation werden zwei Methoden für die Materialcharakterisierung entwickelt, verfeinert und angewandt: eine neuartige Methode zur Messung der Ladungsträgerbeweglichkeit μ und eine Möglichkeit zur Bestimmung der Ionisierungsenergie IE oder der Elektronenaffinität EA eines organischen Halbleiters. Für die Beweglichkeitsmessungen wird eine neue Auswertungsmethode für raumladungsbegrenzte Ströme (SCLC) in unipolaren Bauteilen entwickelt. Sie basiert auf einer Schichtdickenvariation des zu charakterisierenden Materials. In einem Ansatz zur räumlichen Abbildung des elektrischen Potentials (\"potential mapping\", POEM) wird gezeigt, dass das elektrische Potential als Funktion der Schichtdicke V(d) bei einer gegebenen Stromdichte dem räumlichen Verlauf des elektrischen Potentials V(x) im dicksten Bauteil entspricht. Daraus kann die Beweglichkeit als Funktion des elektrischen Felds F und der Ladungsträgerdichte n berechnet werden. Die Auswertung ist modellfrei, d.h. ein Modell zum Angleichen der Messdaten ist für die Berechnung von μ(F, n) nicht erforderlich. Die Messung ist außerdem unabhängig von einer möglichen Injektionsbarriere oder einer Potentialstufe an nicht-idealen Kontakten. Die gemessene Funktion μ(F, n) beschreibt die effektive durchschnittliche Beweglichkeit aller freien und in Fallenzuständen gefangenen Ladungsträger. Dieser Zugang beschreibt den Ladungstransport in energetisch ungeordneten Materialien realistisch, wo eine klare Unterscheidung zwischen freien und Fallenzuständen nicht möglich oder willkürlich ist. Die Messung von IE und EA wird mithilfe temperaturabhängiger Messungen an Solarzellen durchgeführt. In geeigneten Bauteilen mit einem Mischschicht-Heteroübergang (\"bulk heterojunction\" BHJ) ist die Leerlaufspannung Voc im gesamten Messbereich oberhalb 180K eine linear fallende Funktion der Temperatur T. Es kann bestätigt werden, dass die Extrapolation zum Temperaturnullpunkt V0 = Voc(T → 0K) mit der effektiven Energielücke Egeff , d.h. der Differenz zwischen EA des Akzeptor-Materials und IE des Donator-Materials, übereinstimmt. Die systematische schrittweise Variation einzelner Bestandteile der Solarzellen und die Überprüfung des Einflusses auf V0 bestätigen die Beziehung V0 = Egeff. Damit kann die IE oder EA eines Materials bestimmt werden, indem man es in einem BHJ mit einem Material kombiniert, dessen komplementärer Wert bekannt ist. Messungen per Ultraviolett-Photoelektronenspektroskopie (UPS) und inverser Photoelektronenspektroskopie (IPES) werden damit bestätigt, präzisiert und ergänzt. Die beiden entwickelten Messmethoden werden auf organische Halbleiter aus kleinen Molekülen einschließlich Mischschichten angewandt. In Mischschichten aus Zink-Phthalocyanin (ZnPc) und C60 wird eine Löcherbeweglichkeit gemessen, die sowohl thermisch als auch feld- und ladungsträgerdichteaktiviert ist. Wenn das Mischverhältnis variiert wird, steigt die Löcherbeweglichkeit mit zunehmendem ZnPc-Anteil, während die effektive Energielücke unverändert bleibt. Verschiedene weitere Materialien und Materialmischungen werden hinsichtlich Löcher- und Elektronenbeweglichkeit sowie ihrer Energielücke charakterisiert, einschließlich bisher wenig untersuchter hochverdünnter Donator-Systeme. In allen Materialien wird eine deutliche Feldaktivierung der Beweglichkeit beobachtet. Die Ergebnisse ermöglichen eine verbesserte Beschreibung der detaillierten Funktionsweise organischer Solarzellen und unterstützen die künftige Entwicklung hocheffizienter und optimierter Bauteile

In bulk-heterojunction solar cells, device performance is influenced by both the intrinsic properties of the individual components - typically conjugated polymers and fullerene derivatives - and how they assemble and interact at their interface. The ability of fullerene to intercalate within the side-chains of a conjugated polymer can significantly affect the microstructure and overall device performance. Here, a series of computational chemistry approaches are applied to investigate the relationships between structure and property in intercalated polymer:fullerene blend. Using a combination of molecular mechanics (MM) calculation and simulations of 2D grazing incidence X-ray diffraction (GIXD) patterns, we have determined the molecular packing configuration of poly (2,5-bis (3-tetradecyl thiophene-2-yl) thieno[3,2-b]thiophene) (PBTTT-C₁₄) and a blend of PBTTT-C₁₄ and [6,6]-phenyl-C₇₁-butyric acid methyl ester (PC₇₁BM). Based on the confirmed packing structures, the electronic properties and morphological disorder were examined using density functional theory (DFT) and molecular dynamics (MD) calculations, respectively; we also investigated the intermolecular interaction energies behind the structure formation. Finally, we examined the vibrational, redox, and optical properties of the pristine polymer and a series of fullerene derivatives to understand the characteristic modes related to the various charged states of the systems.

Comprendre et modéliser le comportement des matériaux sous irradiation électronique est un enjeu important pour l’industrie spatiale. La fiabilité des satellites nécessite de maîtriser et prédire les potentiels de surface s'établissant sur les diélectriques. Ce travail de doctorat a donc pour objectif de caractériser et de modéliser les différents mécanismes physiques (en surface et en volume) gouvernant le potentiel de charges dans les matériaux polymères spatiaux tels que le Téflon® FEP et le Kapton® HN. La mise au point d'un nouveau dispositif et d'un protocole expérimental a permis de corroborer l'existence d’une conductivité latérale des charges, souvent négligée dans les modèles physiques et numériques. Les études paramétriques, révélant l’influence de l’énergie et le flux des électrons incidents, ont permis de brosser un portrait des processus mis en jeu pour le transport (par saut ou par piégeage/dépiégeage) de charges en surface. A la lumière de cette étude, une conductivité équivalente est extraite, assimilant le matériau à un système prenant en compte les mécanismes de transport volumique et surfacique. L'analyse des évolutions non-monotones de potentiel mesurées sur les polymères spatiaux en condition spatiale a permis de révéler une dépendance de la conductivité volumique induite sous irradiation avec la dose reçue. L'étude paramétrique réalisée sur les mécanismes de transport en volume révèle une influence minoritaire du déplacement du barycentre de charges et du vieillissement physicochimique. Un modèle «0D» à un seul niveau de pièges, prenant en compte les mécanismes de piégeage/dépiégeage et recombinaison entre les porteurs de charges, a été développé. Ce modèle simplifié permet de reproduire qualitativement les évolutions de potentiel expérimentales en fonction du débit de dose et lors d'irradiations successives
Charging behaviours of space dielectric materials, under electron beam irradiation, is of special interest for future spacecraft needs, since this mechanism could induce electrostatic discharges and consequently damages on the sensitive systems on board. In order to assess the risks of charging and discharging, this work aims at understanding the overall charge transport mechanisms and predicting the electrical behaviour of the insulator materials, especially Teflon® FEP and Kapton® HN. For an optimized prediction, the first part of our work is thus to check whether lateral conduction process can take place in the overall charge transport mechanism. Through the definition of a new experimental set-up and protocol, we have been able to discriminate between lateral and bulk conductivity and to reveal the presence of lateral conductivity that is enhanced by radiation ionization processes. We have been able to demonstrate as well that lateral intrinsic conductivity is enhanced with the increase current density and when approaching the sample surface. The second part of our work deals with the characterization of the electrical charging behaviour of Teflon® FEP under multi-energetic electron beam irradiation and the modelling of the overall bulk charge transport mechanisms. An experimental study on charge potential evolution as a function of electron spectrum, electric field, relaxation time, dose and dose rate, was performed. A numerical model has been developed to describe the effect of the different abovementioned mechanisms on the evolution of the surface potential. This model agrees correctly with the experimental phenomenology at qualitative level and therefore allows understanding the physical mechanisms steering charge transport in Teflon® and Kapton®

Solar energy conversion and storage into hydrogen is a valuable approach to capture the energy that is freely available from sunlight and to turn it into a clean fuel. Photoelectrochemical (PEC) water splitting through the dual-absorber tandem cell technology has emerged as a promising strategy to this aim. The work conducted in the frame of this PhD thesis aimed at playing a part in the development and optimization of efficient oxide-based semiconductor photoanodes for water oxidation, which is the kinetic bottleneck of the overall PEC water splitting process. Photoanodes based on films of absorbing materials were successfully synthesized with a high optical transparency as important requirement for maximizing the solar energy conversion efficiency of the final tandem cell device. Subsequently, their intrinsic properties as single photoabsorber photoanodes were largely improved, on the basis of the results obtained through comprehensive PEC studies in parallel with thorough structural, morphological, and spectroscopic investigations. The attention was focused on three different classes of promising ternary metal oxides, able to absorb a large portion of the solar spectrum, namely i) BiVO4 (bandgap Eg = 2.4 eV), known for its excellent solar light to hydrogen conversion efficiency, ii) the copper tungstate-based materials CuWO4 (Eg = 2.3 eV) and CuW(1-x)Mo(x)O4 (Eg = 2.0 eV), ideal to be employed as visible-light active alternative to WO3, and iii) ZnFe2O4 (Eg = 2.0 eV) belonging to the spinel ferrites class, possessing excellent photothermal and chemical stability. Specifically, BiVO4 was studied either as a visible light sensitizer towards TiO2 or as a single photoanode material to focus on the identification and improvement of its intrinsically poor electron transport and interfacial transfer properties. In the first case, the TiO2/BiVO4 heterojunction system was proved to be effective in producing highly reductive electrons, suitable for overall water splitting, through TiO2 sensitization towards visible light. This, together with the counterintuitive mechanism at the basis of the observed impressive functionality, was effectively disclosed through combined PEC and photocatalytic reduction test studies. The multifaceted role of Mo6+ doping onto both the bulk and surface properties of BiVO4 films was also revealed through an in-depth PEC and impedance spectroscopy study. By improving either the bulk conductivity or the interfacial charge transfer of optimized Mo6+ doped BiVO4 photoanodes a conspicuous enhancement was attained of their photoactivity towards water oxidation with respect to the pure material. The presence of intra-gap states in CuWO4, acting as electron traps and thus being responsible for a severe internal charge recombination, was verified by means of the first ultrafast transient absorption study performed with this material, in combination with both an electrochemical and a photochromic characterization. This issue, which strongly limits the PEC performance of CuWO4 photoanodes, was addressed by adopting a 50% Mo for W substitution resulting in CuW0.5Mo0.5O4 photoanodes, exhibiting not only a greatly extended visible light-induced photoactivity compared to the pure material, as a result of enhanced absorption, but also a considerably improved charge separation. All these factors contributed to the much better PEC performance attained with respect to CuWO4 electrodes. This study was finalized by the identification of a suitable hole scavenger species for copper tungstate-based materials, able to ensure enhanced photocurrent generation compared to pure water oxidation while minimizing dark currents. Finally, in the frame of my seven months stage in Prof. Sivula’s group at the EPFL in Lausanne, a thorough study was performed on the impact that several parameters, such as the annealing temperature, the film thickness and the creation of oxygen vacancies through a reductive treatment in hydrogen atmosphere, have on the PEC performance of ZnFe2O4 photoanodes. The verified synergism between the higher crystallinity of the films subjected to a high-temperature annealing treatment and the hydrogenation efficiency, which proved effective in optimizing charge separation in the thicker photoactive layers, allowed one to maximize the performance of ZnFe2O4 electrodes for water oxidation. This study also shed light onto the strict correlation occurring between structural parameters, i.e. the film crystallinity and the spinel inversion degree, and the resulting PEC performance, which proved to be in turn controlled by the film morphology.

The topic of this doctoral thesis is to study the thermal properties of PCM materials and discussion of their use for cooling of photovoltaic systems. The aim of the study is to measure and characterize the thermal properties of commercial PCM materials (Micronal®), their practical use is related to the phase transitions. The behavior of bulk materials at different temperatures is well described theoretically and experimentally verified. For the application use it is necessary to examine and determine the thermal properties of PCM materials depending on the phase transitions during heating and cooling. To study the thermal properties of materials the known transient methods of measuring are used which give full information about the behavior of the materials investigated in dependence on the temperature and thus allow the determination of the thermo-physical parameters of the system. For the transient measurements there are used especially pulse transient and step wise method. Newly is used also combination of linear temperature rise (the ramp wise) and the step wise method. The principle is based on the generation of a small amount of heat inside the studied sample and it is measured the thermal response of the system from which it may be then determined the necessary thermo-physical parameters. The theoretical part of this thesis focuses on characterization of methods for the determination of thermo-physical parameters of the investigated material. In the experimental part of the approached process of experiment, the results, the method of evaluation of the obtained data and also the discussion of results from the viewpoint of potential applications are presented.

This work is focused on developing novel techniques for characterizing organic bulk heterojunction (BHJ) materials for organic photovoltaic (OPV) applications. Polymer:fullerene BHJs are a promising class of photovoltaic materials, but an improved understanding of the charge transport processes and materials science of BHJs is required for them to effectively compete with other photovoltaic systems. Key parameters of BHJ systems that need to be evaluated include both electron and hole mobilities, the carrier concentrations, the recombination mechanism and the recombination coefficient. For these studies, poly(3-hexylthiophene) (P3HT):(6,6)-phenyl C₆₁-butyric acid methyl ester (PCBM) have been characterized due to its wide use among researchers. Traditional characterization techniques have focused on transient measurements in a vertical device configuration, but we demonstrate the use of lateral BHJ devices as materials diagnostic platforms. Lateral devices allow for direct access to the active layer for spatially resolved and environmental effect measurements. The devices are also measured under steady state operation, similar to a working OPV cell. Under these conditions, lateral BHJ devices exhibit space charge limited transport behavior. A detailed charge transport model is presented to describe the potential, electric field, and carrier concentration profiles of lateral BHJ devices, as well as the current versus voltage characteristics of different regions of the device. We are able to calculate the slower carrier mobility from photocurrent measurements of lateral devices and the carrier mobility ratio from the device potential profile, even in ambipolar BHJ systems. In situ potentiometry is used to construct detailed potential profiles of the device channel and calculate both carrier mobilities. The carrier concentration and recombination coefficient are calculated from lateral conductivity measurements, and we show that bimolecular recombination is the dominant mechanism in bulk P3HT:PCBM. A simplified in situ potentiometry and photocurrent measurement technique is presented to measure the time evolution of organic BHJ performance. Due to the open geometry of the lateral BHJ device, we are also able to monitor the change in key charge transport parameters, including the recombination mechanism, in response to environmental degradation, analyte exposure, and ambient temperature. We show increased geminate recombination in P3HT:PC₇₁BM after prolonged light exposure. Lateral BHJ device measurements offer a useful complement to measurements on vertical photovoltaic structures and provide a more complete and detailed picture of OPV materials.
text

The charge transport in disordered organic bulk heterojunction (BHJ) solar cells is a crucial process affecting the power conversion efficiency (PCE) of the solar cell. With the need of synthesizing new materials for improving the power conversion efficiency of those cells it is important to study not only the photophysical but also the electrical properties of the new material classes. Thereby, the experimental techniques need to be applicable to operating solar cells. In this work, the conventional methods of transient photoconductivity (also known as "Time-of-Flight" (TOF)), as well as the transient charge extraction technique of "Charge Carrier Extraction by Linearly Increasing Voltage" (CELIV) are performed on different organic blend compositions. Especially with the latter it is feasible to study the dynamics, i.e. charge transport and charge carrier recombination, in bulk heterojunction (BHJ) solar cells with active layer thicknesses of 100-200 nm. For a well performing organic BHJ solar cells the morphology is the most crucial parameter finding a trade-off between an efficient photogeneration of charge carriers and the transport of the latter to the electrodes. Besides the morphology, the nature of energetic disorder of the active material blend and its influence on the dynamics are discussed extensively in this work. Thereby, the material system of poly(3-hexylthiophene-2,5-diyl) (P3HT) and [6,6]-phenyl-C61 butyric acid methyl ester (PC61BM) serves mainly as a reference material system. New promising donor or acceptor materials and their potential for application in organic photovoltaics are studied in view of charge dynamics and compared with the reference system. With the need for commercialization of organic solar cells the question of the impact of environmental conditions on the PCE of the solar cells raises. In this work, organic BHJ solar cells exposed to synthetic air for finite duration are studied in view of the charge carrier transport and recombination dynamics. Finally, within the framework of this work the technique of photo-CELIV is improved. With the modified technique it is now feasible to study the mobility and lifetime of charge carriers in organic solar cells under operating conditions
Der Ladungstransport in ungeordneten organischen "bulk heterojunction" (Heterogemisch, Abk.: BHJ) Solarzellen stellt einen kritischen Prozess dar, der den Wirkungsgrad wesentlich beeinflusst. Aufgrund der großen Nachfrage neuer, vielversprechender Materialien für die organische Photovoltaik, ist es um so wichtiger nicht nur ihre photophysikalischen sondern auch deren elektrischen Eigenschaften zu charakterisieren. Gerade letztere erfordern experimentelle Messmethoden, die an funktionsfähigen Solarzellen angewandt werden können. Zur experimentellen Untersuchung des Landungstransportes in organischen Solarzellen werden in dieser Arbeit die Methoden der transienten Photoleitfähigkeit, auch bekannt als "Time-of-Flight" (TOF), sowie die transiente Ladungsextraktionsmethode "Charge Carrier Extraction by Linearly Increasing Voltage'' (CELIV) verwendet. Gerade Letztere ermöglicht es an Dünnschichtsystemen von nur wenigen 100 nm, eine typische Schichtdicke bei organischen Solarzellen, den Ladungstransport aber auch die Rekombination von Elektronen und Löchern zu untersuchen. Entscheidend für eine vielversprechende funktionsfähige organische BHJ Solarzelle ist dabei eine günstige Morphologie, die eine effiziente Generation von Ladungsträger, sowie deren Abführung zu den Elektroden erlaubt. Dabei wird in dieser Arbeit der Einfluss der räumlichen, als auch der der energetischen Unordnung der photoaktiven Schicht auf den Ladungstransport und der Rekombination der Ladungsträger untersucht. Das weit verbreitete Materialsystem bestehend aus Poly-3-(Hexyl) Thiophen (P3HT) und [6,6]-Phenyl C61 Buttersäure Methylester (PC61BM) dient dabei als Donator-Akzeptor Referenzsystem. Neuartige Donator- bzw. Akzeptor-Materialien und deren Potential für künftige Anwendungen in der organischen Photovoltaik werden hinsichtlich ihrer Ladungsträgereigenschaften mit dem Referenzmaterialsystem verglichen. Im Zuge der Kommerzialisierung organischer Solarzellen bzw. Solarmodulen ist die Anfälligkeit der Zellen gegenüber äußeren Umwelteinflüssen, wie Sauerstoff oder Wasser, in den Vordergrund des wissenschaftlichen Interesses gerückt. Dementsprechend wird in dieser Arbeit auch der Einfluss von synthetischer Luft auf den Transport und die Rekombination von Ladungsträgern und somit auf den Wirkungsgrad der Solarzelle untersucht und diskutiert. Schließlich wird im Rahmen dieser Arbeit eine Erweiterung der photo-CELIV Messmethode vorgestellt. Diese ermöglicht es die Lebensdauer und den Transport von Ladungsträgern in organischen Dünnschicht-Solarzellen unter realen Arbeitsbedingungen, d.h. Beleuchtung unter einer Sonne bei Raumtemperatur, zu bestimmen

For more than 20 years, scientists have studied solar cells made from organic semiconductors. Throughout this time, device structures have evolved from bilayer devices to bulk heterojunction (BHJ) devices and even though efficiencies are approaching 10%, scientists still know relatively little about the transport of charge carriers and recombination mechanisms in these materials. Novel structures, based on lateral BHJ solar cells, have proven to be versatile tools to study transport and recombination mechanisms. In addition, these structures can easily be employed by researchers and solar cell manufacturers to determine the quality and measure the improvement of their materials. For these studies, poly(3-hexylthiophene) (P3HT):[6,6]-phenyl C61-butyric acid methyl ester (PCBM) has been employed due to its wide use among researchers as well as potential for commercialization. DC photocurrent measurements as a function of device length have yielded the mobility-lifetime product and the generation rate of free carriers within these BHJ devices. In addition to these parameters, the recombination rate as a function of light intensity provides information about the mechanisms of recombination. For example, by measuring the recombination rate as a function of applied electric field and light intensity we have found that recombination is unimolecular in nature and shifts to bimolecular at increased electric field strengths. Additionally, the mobility-lifetime product, generation rate, and recombination mechanism have been studied as a function of applied electric field, illumination spectrum, illumination intensity, etc. This information has provided much insight on physics of the P3HT:PCBM material system which did not exist before these studies.
text

Organic semiconductors are a new key technology for large-area and flexible thin-film electronics. They are deposited as thin films (sub-nanometer to micrometer) on large-area substrates. The technologically most advanced applications are organic light emitting diodes (OLEDs) and organic photovoltaics (OPV). For the improvement of performance and efficiency, correct modeling of the electronic processes in the devices is essential. Reliable characterization and validation of the electronic properties of the materials is simultaneously required for the successful optimization of devices. Furthermore, understanding the relations between material structures and their key characteristics opens the path for innovative material and device design. In this thesis, two material characterization methods are developed, respectively refined and applied: a novel technique for measuring the charge carrier mobility μ and a way to determine the ionization energy IE or the electron affinity EA of an organic semiconductor. For the mobility measurements, a new evaluation approach for space-charge limited current (SCLC) measurements in single carrier devices is developed. It is based on a layer thickness variation of the material under investigation. In the \"potential mapping\" (POEM) approach, the voltage as a function of the device thickness V(d) at a given current density is shown to coincide with the spatial distribution of the electric potential V(x) in the thickest device. On this basis, the mobility is directly obtained as function of the electric field F and the charge carrier density n. The evaluation is model-free, i.e. a model for μ(F, n) to fit the measurement data is not required, and the measurement is independent of a possible injection barrier or potential drop at non-optimal contacts. The obtained μ(F, n) function describes the effective average mobility of free and trapped charge carriers. This approach realistically describes charge transport in energetically disordered materials, where a clear differentiation between trapped and free charges is impossible or arbitrary. The measurement of IE and EA is performed by characterizing solar cells at varying temperature T. In suitably designed devices based on a bulk heterojunction (BHJ), the open-circuit voltage Voc is a linear function of T with negative slope in the whole measured range down to 180K. The extrapolation to temperature zero V0 = Voc(T → 0K) is confirmed to equal the effective gap Egeff, i.e. the difference between the EA of the acceptor and the IE of the donor. The successive variation of different components of the devices and testing their influence on V0 verifies the relation V0 = Egeff. On this basis, the IE or EA of a material can be determined in a BHJ with a material where the complementary value is known. The measurement is applied to a number of material combinations, confirming, refining, and complementing previously reported values from ultraviolet photo electron spectroscopy (UPS) and inverse photo electron spectroscopy (IPES). These measurements are applied to small molecule organic semiconductors, including mixed layers. In blends of zinc-phthalocyanine (ZnPc) and C60, the hole mobility is found to be thermally and field activated, as well as increasing with charge density. Varying the mixing ratio, the hole mobility is found to increase with increasing ZnPc content, while the effective gap stays unchanged. A number of further materials and material blends are characterized with respect to hole and electron mobility and the effective gap, including highly diluted donor blends, which have been little investigated before. In all materials, a pronounced field activation of the mobility is observed. The results enable an improved detailed description of the working principle of organic solar cells and support the future design of highly efficient and optimized devices.:1. Introduction 2. Organic semiconductors and devices 2.1. Organic semiconductors 2.1.1. Conjugated π system 2.1.2. Small molecules and polymers 2.1.3. Disorder in amorphous materials 2.1.4. Polarons 2.1.5. Polaron hopping 2.1.6. Fermi-Dirac distribution and Fermi level 2.1.7. Quasi-Fermi levels 2.1.8. Trap states 2.1.9. Doping 2.1.10. Excitons 2.2. Interfaces and blend layers 2.2.1. Interface dipoles 2.2.2. Energy level bending 2.2.3. Injection from metal into semiconductor, and extraction 2.2.4. Excitons at interfaces 2.3. Charge transport and recombination in organic semiconductors 2.3.1. Drift transport 2.3.2. Charge carrier mobility 2.3.3. Thermally activated transport 2.3.4. Diffusion transport 2.3.5. Drift-diffusion transport 2.3.6. Space-charge limited current 2.3.7. Recombination 2.4. Mobility measurement 2.4.1. SCLC and TCLC 2.4.2. Time of flight 2.4.3. Organic field effect transistors 2.4.4. CELIV 2.5. Organic solar cells 2.5.1. Exciton diffusion towards the interface 2.5.2. Dissociation of CT states 2.5.3. CT recombination 2.5.4. Flat and bulk heterojunction 2.5.5. Transport layers 2.5.6. Thin film optics 2.5.7. Current-voltage characteristics and equivalent circuit 2.5.8. Solar cell efficiency 2.5.9. Limits of efficiency 2.5.10. Correct solar cell characterization 2.5.11. The \"O-Factor\" 3. Materials and experimental methods 3.1. Materials 3.2. Device fabrication and layout 3.2.1. Layer deposition 3.2.2. Encapsulation 3.2.3. Homogeneity of layer thickness on a wafer 3.2.4. Device layout 3.3. Characterization 3.3.1. Electrical characterization 3.3.2. Sample illumination 3.3.3. Temperature dependent characterization 3.3.4. UPS 4. Simulations 5.1. Design of single carrier devices 5.1.1. General design requirements 5.1.2. Single carrier devices for space-charge limited current 5.1.3. Ohmic regime 5.1.4. Design of injection and extraction layers 5.2. Advanced evaluation of SCLC – potential mapping 5.2.1. Potential mapping by thickness variation 5.2.2. Further evaluation of the transport profile 5.2.3. Injection into and extraction from single carrier devices 5.2.4. Majority carrier approximation 5.3. Proof of principle: POEM on simulated data 5.3.1. Constant mobility 5.3.2. Field dependent mobility 5.3.3. Field and charge density activated mobility 5.3.4. Conclusion 5.4. Application: Transport characterization in organic semiconductors 5.4.1. Hole transport in ZnPc:C60 5.4.2. Hole transport in ZnPc:C60 – temperature variation 5.4.3. Hole transport in ZnPc:C60 – blend ratio variation 5.4.4. Hole transport in ZnPc:C70 5.4.5. Hole transport in neat ZnPc 5.4.6. Hole transport in F4-ZnPc:C60 5.4.7. Hole transport in DCV-5T-Me33:C60 5.4.8. Electron transport in ZnPc:C60 5.4.9. Electron transport in neat Bis-HFl-NTCDI 5.5. Summary and discussion of the results 5.5.1. Phthalocyanine:C60 blends 5.5.2. DCV-5T-Me33:C60 5.5.3. Conclusion 6. Organic solar cell characteristics: the influence of temperature 6.1. ZnPc:C60 solar cells 6.1.1. Temperature variation 6.1.2. Illumination intensity variation 6.2. Voc in flat and bulk heterojunction organic solar cells 6.2.1. Qualitative difference in Voc(I, T) 6.2.2. Interpretation of Voc(I, T) 6.3. BHJ stoichiometry variation 6.3.1. Voc upon variation of stoichiometry and contact layer 6.3.2. V0 upon stoichiometry variation 6.3.3. Low donor content stoichiometry 6.3.4. Conclusion from stoichiometry variation 6.4. Transport material variation 6.4.1. HTM variation 6.4.2. ETM variation 6.5. Donor:acceptor material variation 6.5.1. Donor variation 6.5.2. Acceptor variation 6.6. Conclusion 7. Summary and outlook 7.1. Summary 7.2. Outlook A. Appendix A.1. Energy pay-back of this thesis A.2. Tables and registers
Organische Halbleiter sind eine neue Schlüsseltechnologie für großflächige und flexible Dünnschichtelektronik. Sie werden als dünne Materialschichten (Sub-Nanometer bis Mikrometer) auf großflächige Substrate aufgebracht. Die technologisch am weitesten fortgeschrittenen Anwendungen sind organische Leuchtdioden (OLEDs) und organische Photovoltaik (OPV). Zur weiteren Steigerung von Leistungsfähigkeit und Effizienz ist die genaue Modellierung elektronischer Prozesse in den Bauteilen von grundlegender Bedeutung. Für die erfolgreiche Optimierung von Bauteilen ist eine zuverlässige Charakterisierung und Validierung der elektronischen Materialeigenschaften gleichermaßen erforderlich. Außerdem eröffnet das Verständnis der Zusammenhänge zwischen Materialstruktur und -eigenschaften einen Weg für innovative Material- und Bauteilentwicklung. Im Rahmen dieser Dissertation werden zwei Methoden für die Materialcharakterisierung entwickelt, verfeinert und angewandt: eine neuartige Methode zur Messung der Ladungsträgerbeweglichkeit μ und eine Möglichkeit zur Bestimmung der Ionisierungsenergie IE oder der Elektronenaffinität EA eines organischen Halbleiters. Für die Beweglichkeitsmessungen wird eine neue Auswertungsmethode für raumladungsbegrenzte Ströme (SCLC) in unipolaren Bauteilen entwickelt. Sie basiert auf einer Schichtdickenvariation des zu charakterisierenden Materials. In einem Ansatz zur räumlichen Abbildung des elektrischen Potentials (\"potential mapping\", POEM) wird gezeigt, dass das elektrische Potential als Funktion der Schichtdicke V(d) bei einer gegebenen Stromdichte dem räumlichen Verlauf des elektrischen Potentials V(x) im dicksten Bauteil entspricht. Daraus kann die Beweglichkeit als Funktion des elektrischen Felds F und der Ladungsträgerdichte n berechnet werden. Die Auswertung ist modellfrei, d.h. ein Modell zum Angleichen der Messdaten ist für die Berechnung von μ(F, n) nicht erforderlich. Die Messung ist außerdem unabhängig von einer möglichen Injektionsbarriere oder einer Potentialstufe an nicht-idealen Kontakten. Die gemessene Funktion μ(F, n) beschreibt die effektive durchschnittliche Beweglichkeit aller freien und in Fallenzuständen gefangenen Ladungsträger. Dieser Zugang beschreibt den Ladungstransport in energetisch ungeordneten Materialien realistisch, wo eine klare Unterscheidung zwischen freien und Fallenzuständen nicht möglich oder willkürlich ist. Die Messung von IE und EA wird mithilfe temperaturabhängiger Messungen an Solarzellen durchgeführt. In geeigneten Bauteilen mit einem Mischschicht-Heteroübergang (\"bulk heterojunction\" BHJ) ist die Leerlaufspannung Voc im gesamten Messbereich oberhalb 180K eine linear fallende Funktion der Temperatur T. Es kann bestätigt werden, dass die Extrapolation zum Temperaturnullpunkt V0 = Voc(T → 0K) mit der effektiven Energielücke Egeff , d.h. der Differenz zwischen EA des Akzeptor-Materials und IE des Donator-Materials, übereinstimmt. Die systematische schrittweise Variation einzelner Bestandteile der Solarzellen und die Überprüfung des Einflusses auf V0 bestätigen die Beziehung V0 = Egeff. Damit kann die IE oder EA eines Materials bestimmt werden, indem man es in einem BHJ mit einem Material kombiniert, dessen komplementärer Wert bekannt ist. Messungen per Ultraviolett-Photoelektronenspektroskopie (UPS) und inverser Photoelektronenspektroskopie (IPES) werden damit bestätigt, präzisiert und ergänzt. Die beiden entwickelten Messmethoden werden auf organische Halbleiter aus kleinen Molekülen einschließlich Mischschichten angewandt. In Mischschichten aus Zink-Phthalocyanin (ZnPc) und C60 wird eine Löcherbeweglichkeit gemessen, die sowohl thermisch als auch feld- und ladungsträgerdichteaktiviert ist. Wenn das Mischverhältnis variiert wird, steigt die Löcherbeweglichkeit mit zunehmendem ZnPc-Anteil, während die effektive Energielücke unverändert bleibt. Verschiedene weitere Materialien und Materialmischungen werden hinsichtlich Löcher- und Elektronenbeweglichkeit sowie ihrer Energielücke charakterisiert, einschließlich bisher wenig untersuchter hochverdünnter Donator-Systeme. In allen Materialien wird eine deutliche Feldaktivierung der Beweglichkeit beobachtet. Die Ergebnisse ermöglichen eine verbesserte Beschreibung der detaillierten Funktionsweise organischer Solarzellen und unterstützen die künftige Entwicklung hocheffizienter und optimierter Bauteile.:1. Introduction 2. Organic semiconductors and devices 2.1. Organic semiconductors 2.1.1. Conjugated π system 2.1.2. Small molecules and polymers 2.1.3. Disorder in amorphous materials 2.1.4. Polarons 2.1.5. Polaron hopping 2.1.6. Fermi-Dirac distribution and Fermi level 2.1.7. Quasi-Fermi levels 2.1.8. Trap states 2.1.9. Doping 2.1.10. Excitons 2.2. Interfaces and blend layers 2.2.1. Interface dipoles 2.2.2. Energy level bending 2.2.3. Injection from metal into semiconductor, and extraction 2.2.4. Excitons at interfaces 2.3. Charge transport and recombination in organic semiconductors 2.3.1. Drift transport 2.3.2. Charge carrier mobility 2.3.3. Thermally activated transport 2.3.4. Diffusion transport 2.3.5. Drift-diffusion transport 2.3.6. Space-charge limited current 2.3.7. Recombination 2.4. Mobility measurement 2.4.1. SCLC and TCLC 2.4.2. Time of flight 2.4.3. Organic field effect transistors 2.4.4. CELIV 2.5. Organic solar cells 2.5.1. Exciton diffusion towards the interface 2.5.2. Dissociation of CT states 2.5.3. CT recombination 2.5.4. Flat and bulk heterojunction 2.5.5. Transport layers 2.5.6. Thin film optics 2.5.7. Current-voltage characteristics and equivalent circuit 2.5.8. Solar cell efficiency 2.5.9. Limits of efficiency 2.5.10. Correct solar cell characterization 2.5.11. The \"O-Factor\" 3. Materials and experimental methods 3.1. Materials 3.2. Device fabrication and layout 3.2.1. Layer deposition 3.2.2. Encapsulation 3.2.3. Homogeneity of layer thickness on a wafer 3.2.4. Device layout 3.3. Characterization 3.3.1. Electrical characterization 3.3.2. Sample illumination 3.3.3. Temperature dependent characterization 3.3.4. UPS 4. Simulations 5.1. Design of single carrier devices 5.1.1. General design requirements 5.1.2. Single carrier devices for space-charge limited current 5.1.3. Ohmic regime 5.1.4. Design of injection and extraction layers 5.2. Advanced evaluation of SCLC – potential mapping 5.2.1. Potential mapping by thickness variation 5.2.2. Further evaluation of the transport profile 5.2.3. Injection into and extraction from single carrier devices 5.2.4. Majority carrier approximation 5.3. Proof of principle: POEM on simulated data 5.3.1. Constant mobility 5.3.2. Field dependent mobility 5.3.3. Field and charge density activated mobility 5.3.4. Conclusion 5.4. Application: Transport characterization in organic semiconductors 5.4.1. Hole transport in ZnPc:C60 5.4.2. Hole transport in ZnPc:C60 – temperature variation 5.4.3. Hole transport in ZnPc:C60 – blend ratio variation 5.4.4. Hole transport in ZnPc:C70 5.4.5. Hole transport in neat ZnPc 5.4.6. Hole transport in F4-ZnPc:C60 5.4.7. Hole transport in DCV-5T-Me33:C60 5.4.8. Electron transport in ZnPc:C60 5.4.9. Electron transport in neat Bis-HFl-NTCDI 5.5. Summary and discussion of the results 5.5.1. Phthalocyanine:C60 blends 5.5.2. DCV-5T-Me33:C60 5.5.3. Conclusion 6. Organic solar cell characteristics: the influence of temperature 6.1. ZnPc:C60 solar cells 6.1.1. Temperature variation 6.1.2. Illumination intensity variation 6.2. Voc in flat and bulk heterojunction organic solar cells 6.2.1. Qualitative difference in Voc(I, T) 6.2.2. Interpretation of Voc(I, T) 6.3. BHJ stoichiometry variation 6.3.1. Voc upon variation of stoichiometry and contact layer 6.3.2. V0 upon stoichiometry variation 6.3.3. Low donor content stoichiometry 6.3.4. Conclusion from stoichiometry variation 6.4. Transport material variation 6.4.1. HTM variation 6.4.2. ETM variation 6.5. Donor:acceptor material variation 6.5.1. Donor variation 6.5.2. Acceptor variation 6.6. Conclusion 7. Summary and outlook 7.1. Summary 7.2. Outlook A. Appendix A.1. Energy pay-back of this thesis A.2. Tables and registers