Dissertations / Theses: 'Buckling capacity'

1

O'Neill, Leah. "Lateral-Torsional Buckling Capacity of Tapered-Flange Moment Frame Shapes." BYU ScholarsArchive, 2014. https://scholarsarchive.byu.edu/etd/5759.

Full text

Abstract:

While moment frames are a popular lateral-force resisting system, their constant cross-section can lead to inefficiencies in energy absorption and stiffness. By tapering the flange width linearly toward the center of the beam length, the energy absorption efficiency can be increased, leading to a better elastic response from the beam and more elastic stiffness per pound of steel used. Lateral-torsional buckling is an important failure mode to be considered for tapered-flange moment frame shapes. No closed-form or finite element solutions have yet been developed for tapered-flange I-beams with a non-uniform, linear moment gradient and intermediate bracing conditions. In this study, finite element analysis is used to find the buckling stress of each W-shape in the AISC Steel Construction Manual with both a standard straight-flange and the proposed tapered-flange at several lengths and with three intermediate lateral bracing conditions (no bracing, mid-span bracing, and third-span bracing). Plots are generated for each shape at each bracing condition as the buckling stress versus length for both beams and columns. Overall, the results indicate that lateral-torsional buckling of tapered-flange I-beams is not a problem that would prohibit the wide-scale use of this configuration in moment frames. Also, the buckling capacity tapered-flange moment frame shapes can be reasonably estimated as 20% of the corresponding straight-flange moment frame shape.

APA, Harvard, Vancouver, ISO, and other styles

2

Sun, Miao. "Use of Material Tailoring to Improve Axial Load Capacity of Elliptical Composite Cylinders." Diss., Virginia Tech, 2006. http://hdl.handle.net/10919/29693.

Full text

Abstract:

This study focuses on the improvement of the axial buckling capacity of elliptical composite cylinders through the use of a circumferentially-varying lamination sequence. The concept of varying the lamination sequence around the circumference is considered as a viable approach for off-setting the disadvantages of having the cylinder radius of curvature vary with circumferential position, the source of the reduced buckling capacity when compared to a circular cylinder with the same circumference. Post-buckling collapse behavior and material failure characteristics are also of interest. Two approaches to implementing a circumferential variation of lamination are examined. For the first approach the lamination sequence is varied in a stepwise fashion around the circumference. Specifically, each quadrant of the cylinder circumference is divided into three equal-length regions denoted as the crown, middle, and side regions. Eight different cylinders designs, whereby each region is constructed of either a quasi-isotropic or an axially-stiff laminate of equal thickness, are studied. Results are compared to the baseline case of an elliptical cylinder constructed entirely of a quasi-isotropic laminate. Since the thickness of the quasi-isotropic and axially-stiff laminates are the same, all cylinders weight the same and thus comparisons are meaningful. Improvements upwards of 18% in axial buckling capacity can be achieved with one particular stepwise design. The second approach considers laminations that vary circumferentially in a continuous fashion to mitigate the effects of the continuously-varying radius of curvature. The methodology for determining how to tailor the lamination sequence circumferentially is based on the analytical predictions of a simple buckling analysis for simply-supported circular cylinders. With this approach, axial buckling load improvements upwards of 30% are realized. Of all the cylinders considered, very few do not exhibit material failure upon collapse in the post-buckled state. Of those that do not, there is little, if any, improvement in bucking capacity. Results for the pre-buckling, buckling, post-buckling, and material failure are obtained from the finite-element code ABAQUS using both static and dynamic analyses. Studies with the code demonstrate that the results obtained are converged.
Ph. D.

APA, Harvard, Vancouver, ISO, and other styles

3

Qin, Yi. "Numerical analysis of inelastic local web buckling capacity of coped steel I-beam." Thesis, University of Macau, 2012. http://umaclib3.umac.mo/record=b2586272.

Full text

APA, Harvard, Vancouver, ISO, and other styles

4

Islam, Amjad, Stephen U. Nwokoli, and Tatek Debebe. "Bearing Capacity of I-Joists." Thesis, Linnéuniversitetet, Institutionen för teknik, TEK, 2011. http://urn.kb.se/resolve?urn=urn:nbn:se:lnu:diva-12703.

Full text

Abstract:

This work deals with the bearing capacity of wood based I-joists Finite element models were analyzed to determine the bearing capacity of I-joists, using the finite element software Abaqus CAE. The purpose of this study is to compare the results from the developed FE-models with experimental results, and with a previously proposed design formula. To perform the analyses finite element models were created. The model consists of three parts:, the web (made of shell element), the flanges and steel plates used at the supports and loading points (made of solid elements) To determine the bearing capacity of the I-joist two types of analyses were performed, a linear buckling analysis to check the risk of web buckling and a static (stress) analysis to check the risk of splitting of the flanges. This study shows that the steel plate length, in some cases, has little or no impact on primarily the splitting load. Furthermore, the buckling load decreases as the depth of the beam increases, the influence of the depth being proportional to 1/h2. The depth of the beam has no impact on the risk of splitting of the flange.

APA, Harvard, Vancouver, ISO, and other styles

5

Al-Azzawi, Zaid Mohammed Kani. "Capacity of FRP strengthened steel plate girders against shear buckling under static and cyclic loading." Thesis, University of Edinburgh, 2016. http://hdl.handle.net/1842/25453.

Full text

Abstract:

Civil engineers are presently faced with the challenge of strengthening and repairing many existing structures to assure or increase their structural safety. The reasons for this include changes in the use of structures, and increased traffic loads on bridges. In Iraq, for example, several highway bridges needed to accommodate increased axle load during the transportation of huge turbines for electricity generating stations. The requirement for structural strengthening and repair methods is, however, driven by the worldwide need to ensure the safety and sustainability of our aging infrastructure which is deteriorating at a rate faster than it can be renovated. The ever increasing damage caused by environmental effects and the corrosion of steel and deterioration of concrete, reduce structural safety and lead to disruption for the users, which can have serious economic consequences. In a plate girder bridge, the plate girders are typically I-beams made up from separate structural steel plates (rather than rolled as a single cross-section), which are welded or, in older bridges, bolted or riveted together to form the vertical web and horizontal flanges of the beam. The two primary functions of the web plate in a plate girder are to maintain a relative distance between the top and bottom flanges and to resist the induced shear stresses. In most practical ranges of plate girder bridges’ spans, the induced shear stresses are relatively low compared to the bending stresses in the flanges induced by flexure. As a result the web plate is generally chosen to be much thinner than the flanges. The web panel consequently buckles at a relatively low shear force. For steel girder structures dominated by cyclic loading, as is the case with repeated vehicle axle loads on bridges, this can lead to the so-called ‘breathing’ phenomenon; an out-of-plane buckling displacement that can induce high secondary bending stresses at the welded plate boundaries. In the current work, a novel FRP strengthening technique using bonded shapes is applied to resist these out of plane deformations, and hence reduce the breathing stresses, and improve the fatigue life of the plate girder which is very different to the majority of applications of FRP strengthening that exploit the FRP for its direct tensile strength and stiffness. The objective of the current experimental programme is to strengthen thinwalled steel girders against web shear buckling using a corrugated CFRP or GFRP panel bonded externally along the compression diagonal of the web plate. The programme was divided into three main phases, including: (1) the development of a new preformed corrugated FRP panel, and (2, 3) testing its performance in two main experimental series. The initial series involved tests on 13 steel plates strengthened with the proposed preformed corrugated FRP panel and subjected to in-plane shear loading using a specially manufactured “picture-frame” arrangement designed to induce the appropriate boundary conditions and stresses in the web plates. This initial test series investigated the performance of different forms of strengthening under static load, in preparation for another series of cyclic tests to investigate their fatigue performance. The test variables included FRP type (CFRP or GFRP), form of FRP (closed or open section), number of FRP layers, and orientation of GFRP fibres used to produce the FRP panel. In the second series, six specimens were manufactured to simulate the end panel of a plate girder. These were strengthened with the optimized FRP panel from the initial series and tested for shear buckling under repeated cyclic loading with a stress range 40-80% of the static ultimate capacity. A considerable increase in the stiffness of the strengthened specimens is evident in the observed reductions of the maximum out-of-plane displacement. The stiffness of the strengthened specimens is assessed to be increased by a factor ranging between 3 to 9 times the stiffness of the corresponding unstrengthened specimen, depending upon the type of the FRP panel used and the aspect ratio of the tested specimens. The breathing phenomena is also significantly reduced, consequently the surface, membrane and secondary bending stresses are reduced. The 45° strengthening scheme succeeded the best both in reducing the breathing stresses and increasing the ultimate shear capacity of the specimen by 88%. Fatigue analyses indicated that the proposed strengthening technique is able to considerably elongate the life expectancy of the strengthened plate girders by a factor ranging between 2.5 and 7 depending on the applied cyclic load amplitude. In addition, the proposed strengthening technique did not show any debonding or delamination under both static and cyclic loading which makes it a good candidate for strengthening thin-walled structural members, especially, when ductility is a concern. In fact, the proposed strengthening technique succeeded in improving the energy absorption capacity of the strengthened specimens by a factor ranging between 1.5 and 2.5 times the corresponding control specimen which means that the ductile failure type associated with shear buckling of steel plate girders is not only maintained, but it was improved as well. This type of ductile failure is not common in other types of FRP strengthening techniques. Finally, a geometrical and material non-linear finite element model is presented both for the steel and composite sections which showed very good correlation with test results and was capable of predicting both the strength and deformational behaviour of the tested specimens. This numerical model is used for a parametric study to support the proposed design method.

APA, Harvard, Vancouver, ISO, and other styles

6

Takeda, Hachirho. "A fundamental study on simplified analysis of buckling, load-carrying capacity and deformability of girders." 京都大学 (Kyoto University), 2004. http://hdl.handle.net/2433/131965.

Full text

APA, Harvard, Vancouver, ISO, and other styles

7

Venter, Simon Herman. "The effect of the adjacent span on the lateral-torsional buckling capacity of overhang beams." Diss., University of Pretoria, 2017. http://hdl.handle.net/2263/62800.

Full text

APA, Harvard, Vancouver, ISO, and other styles

8

Koen, Damien Joseph. "Structural Capacity of Light Gauge Steel Storage Rack Uprights." Thesis, The University of Sydney, 2008. http://hdl.handle.net/2123/3880.

Full text

Abstract:

This report investigates the down-aisle buckling load capacity of steel storage rack uprights. The effects of discrete torsional restraints provided by the frame bracing in the cross-aisle direction is considered in this report. Since current theoretical methods used to predict the buckling capacity of rack uprights appear to be over-conservative and complex, this research may provide engineers an alternative method of design using detailed finite element analysis. In this study, the results from experimental testing of upright frames with K-bracing are compared to finite element predictions of displacements and maximum axial loads. The finite element analysis is then used to determine the buckling loads on braced and un-braced uprights of various lengths. The upright capacities can then be compared with standard design methods which generally do not accurately take into account the torsional resistance that the cross-aisle frame bracing provides to the upright. The information contained in this report would be beneficial to engineers or manufacturers who are involved in the design of rack uprights or other discretely braced complex light gauge steel members subject to axial loads.

APA, Harvard, Vancouver, ISO, and other styles

9

Koen, Damien Joseph. "Structural Capacity of Light Gauge Steel Storage Rack Uprights." University of Sydney, 2008. http://hdl.handle.net/2123/3880.

Full text

Abstract:

Master of Engineering (Research)
This report investigates the down-aisle buckling load capacity of steel storage rack uprights. The effects of discrete torsional restraints provided by the frame bracing in the cross-aisle direction is considered in this report. Since current theoretical methods used to predict the buckling capacity of rack uprights appear to be over-conservative and complex, this research may provide engineers an alternative method of design using detailed finite element analysis. In this study, the results from experimental testing of upright frames with K-bracing are compared to finite element predictions of displacements and maximum axial loads. The finite element analysis is then used to determine the buckling loads on braced and un-braced uprights of various lengths. The upright capacities can then be compared with standard design methods which generally do not accurately take into account the torsional resistance that the cross-aisle frame bracing provides to the upright. The information contained in this report would be beneficial to engineers or manufacturers who are involved in the design of rack uprights or other discretely braced complex light gauge steel members subject to axial loads.

APA, Harvard, Vancouver, ISO, and other styles

10

Yuan, Zeng. "Advanced Analysis of Steel Frame Structures Subjected to Lateral Torsional Buckling Effects." Thesis, Queensland University of Technology, 2004. https://eprints.qut.edu.au/15980/1/Zeng_Yuan_Thesis.pdf.

Full text

Abstract:

The current design procedure for steel frame structures is a two-step process including an elastic analysis to determine design actions and a separate member capacity check. This design procedure is unable to trace the full range of load-deflection response and hence the failure modes of the frame structures can not be accurately predicted. In recent years, the development of advanced analysis methods has aimed at solving this problem by combining the analysis and design tasks into one step. Application of the new advanced analysis methods permits a comprehensive assessment of the actual failure modes and ultimate strengths of structural steel systems in practical design situations. One of the advanced analysis methods, the refined plastic hinge method, has shown great potential to become a practical design tool. However, at present, it is only suitable for a special class of steel frame structures that is not subject to lateral torsional buckling effects. The refined plastic hinge analysis can directly account for three types of frame failures, gradual formation of plastic hinges, column buckling and local buckling. However, this precludes most of the steel frame structures whose behaviour is governed by lateral torsional buckling. Therefore, the aim of this research is to develop a practical advanced analysis method suitable for general steel frame structures including the effects of lateral-torsional buckling. Lateral torsional buckling is a complex three dimensional instability phenomenon. Unlike the in-plane buckling of beam-columns, a closed form analytical solution is not available for lateral torsional buckling. The member capacity equations used in design specifications are derived mainly from testing of simply supported beams. Further, there has been very limited research into the behaviour and design of steel frame structures subject to lateral torsional buckling failures. Therefore in order to incorporate lateral torsional buckling effects into an advanced analysis method, a detailed study must be carried out including inelastic beam buckling failures. This thesis contains a detailed description of research on extending the scope of advanced analysis by developing methods that include the effects of lateral torsional buckling in a nonlinear analysis formulation. It has two components. Firstly, distributed plasticity models were developed using the state-of-the-art finite element analysis programs for a range of simply supported beams and rigid frame structures to investigate and fully understand their lateral torsional buckling behavioural characteristics. Nonlinear analyses were conducted to study the load-deflection response of these structures under lateral torsional buckling influences. It was found that the behaviour of simply supported beams and members in rigid frame structures is significantly different. In real frame structures, the connection details are a decisive factor in terms of ultimate frame capacities. Accounting for the connection rigidities in a simplified advanced analysis method is very difficult, but is most critical. Generally, the finite element analysis results of simply supported beams agree very well with the predictions of the current Australian steel structures design code AS4100, but the capacities of rigid frame structures can be significantly higher compared with Australian code predictions. The second part of the thesis concerns the development of a two dimensional refined plastic hinge analysis which is capable of considering lateral torsional buckling effects. The formulation of the new method is based on the observations from the distributed plasticity analyses of both simply supported beams and rigid frame structures. The lateral torsional buckling effects are taken into account implicitly using a flexural stiffness reduction factor in the stiffness matrix formulation based on the member capacities specified by AS4100. Due to the lack of suitable alternatives, concepts of moment modification and effective length factors are still used for determining the member capacities. The effects of connection rigidities and restraints from adjacent members are handled by using appropriate effective length factors in the analysis. Compared with the benchmark solutions for simply supported beams, the new refined plastic hinge analysis is very accurate. For rigid frame structures, the new method is generally more conservative than the finite element models. The accuracy of the new method relies on the user's judgement of beam segment restraints. Overall, the design capacities in the new method are superior to those in the current design procedure, especially for frame structures with less slender members. The new refined plastic hinge analysis is now able to capture four types of failure modes, plastic hinge formation, column buckling, local buckling and lateral torsional buckling. With the inclusion of lateral torsional buckling mode as proposed in this thesis, advanced analysis is one step closer to being used for general design practice.

APA, Harvard, Vancouver, ISO, and other styles

11

Yuan, Zeng. "Advanced Analysis of Steel Frame Structures Subjected to Lateral Torsional Buckling Effects." Queensland University of Technology, 2004. http://eprints.qut.edu.au/15980/.

Full text

Abstract:

The current design procedure for steel frame structures is a two-step process including an elastic analysis to determine design actions and a separate member capacity check. This design procedure is unable to trace the full range of load-deflection response and hence the failure modes of the frame structures can not be accurately predicted. In recent years, the development of advanced analysis methods has aimed at solving this problem by combining the analysis and design tasks into one step. Application of the new advanced analysis methods permits a comprehensive assessment of the actual failure modes and ultimate strengths of structural steel systems in practical design situations. One of the advanced analysis methods, the refined plastic hinge method, has shown great potential to become a practical design tool. However, at present, it is only suitable for a special class of steel frame structures that is not subject to lateral torsional buckling effects. The refined plastic hinge analysis can directly account for three types of frame failures, gradual formation of plastic hinges, column buckling and local buckling. However, this precludes most of the steel frame structures whose behaviour is governed by lateral torsional buckling. Therefore, the aim of this research is to develop a practical advanced analysis method suitable for general steel frame structures including the effects of lateral-torsional buckling. Lateral torsional buckling is a complex three dimensional instability phenomenon. Unlike the in-plane buckling of beam-columns, a closed form analytical solution is not available for lateral torsional buckling. The member capacity equations used in design specifications are derived mainly from testing of simply supported beams. Further, there has been very limited research into the behaviour and design of steel frame structures subject to lateral torsional buckling failures. Therefore in order to incorporate lateral torsional buckling effects into an advanced analysis method, a detailed study must be carried out including inelastic beam buckling failures. This thesis contains a detailed description of research on extending the scope of advanced analysis by developing methods that include the effects of lateral torsional buckling in a nonlinear analysis formulation. It has two components. Firstly, distributed plasticity models were developed using the state-of-the-art finite element analysis programs for a range of simply supported beams and rigid frame structures to investigate and fully understand their lateral torsional buckling behavioural characteristics. Nonlinear analyses were conducted to study the load-deflection response of these structures under lateral torsional buckling influences. It was found that the behaviour of simply supported beams and members in rigid frame structures is significantly different. In real frame structures, the connection details are a decisive factor in terms of ultimate frame capacities. Accounting for the connection rigidities in a simplified advanced analysis method is very difficult, but is most critical. Generally, the finite element analysis results of simply supported beams agree very well with the predictions of the current Australian steel structures design code AS4100, but the capacities of rigid frame structures can be significantly higher compared with Australian code predictions. The second part of the thesis concerns the development of a two dimensional refined plastic hinge analysis which is capable of considering lateral torsional buckling effects. The formulation of the new method is based on the observations from the distributed plasticity analyses of both simply supported beams and rigid frame structures. The lateral torsional buckling effects are taken into account implicitly using a flexural stiffness reduction factor in the stiffness matrix formulation based on the member capacities specified by AS4100. Due to the lack of suitable alternatives, concepts of moment modification and effective length factors are still used for determining the member capacities. The effects of connection rigidities and restraints from adjacent members are handled by using appropriate effective length factors in the analysis. Compared with the benchmark solutions for simply supported beams, the new refined plastic hinge analysis is very accurate. For rigid frame structures, the new method is generally more conservative than the finite element models. The accuracy of the new method relies on the user's judgement of beam segment restraints. Overall, the design capacities in the new method are superior to those in the current design procedure, especially for frame structures with less slender members. The new refined plastic hinge analysis is now able to capture four types of failure modes, plastic hinge formation, column buckling, local buckling and lateral torsional buckling. With the inclusion of lateral torsional buckling mode as proposed in this thesis, advanced analysis is one step closer to being used for general design practice.

APA, Harvard, Vancouver, ISO, and other styles

12

Perera, Nilakshi. "Structural behaviour and design of innovative hollow flange steel plate grinders." Thesis, Queensland University of Technology, 2018. https://eprints.qut.edu.au/123310/1/Liyanage%20Nilakshi%20Piyahasi_Perera_Thesis.pdf.

Full text

Abstract:

This thesis proposes a new Hollow Flange Steel Plate Girder (HFSPG) by welding industrially available cold-formed Rectangular Hollow Sections (RHS) to a web plate for use in long span construction. Design procedures presented in the national and international design guidelines were reviewed and suitable improvements were made to accurately predict the structural behaviour and capacities of HFSPGs by undertaking detailed experimental and numerical studies into their unique structural behaviour. Local buckling/yielding, global buckling and local-global interaction failures were all considered in this thesis.

APA, Harvard, Vancouver, ISO, and other styles

13

Cheng, Shanshan. "Fire performance of cold-formed steel sections." Thesis, University of Plymouth, 2015. http://hdl.handle.net/10026.1/3316.

Full text

Abstract:

Thin-walled cold-formed steel (CFS) has exhibited inherent structural and architectural advantages over other constructional materials, for example, high strength-to-weight ratio, ease of fabrication, economy in transportation and the flexibility of sectional profiles, which make CFS ideal for modern residential and industrial buildings. They have been increasingly used as purlins as the intermediate members in a roof system, or load-bearing components in low- and mid-rise buildings. However, using CFS members in building structures has been facing challenges due to the lack of knowledge to the fire performance of CFS at elevated temperatures and the lack of fire design guidelines. Among all available design specifications of CFS, EN1993-1-2 is the only one which provided design guidelines for CFS at elevated temperatures, which, however, is based on the same theory and material properties of hot-rolled steel. Since the material properties of CFS are found to be considerably different from those of hot-rolled steel, the applicability of hot-rolled steel design guidelines into CFS needs to be verified. Besides, the effect of non-uniform temperature distribution on the failure of CFS members is not properly addressed in literature and has not been specified in the existing design guidelines. Therefore, a better understanding of fire performance of CFS members is of great significance to further explore the potential application of CFS. Since CFS members are always with thin thickness (normally from 0.9 to 8 mm), open cross-section, and great flexural rigidity about one axis at the expense of low flexural rigidity about a perpendicular axis, the members are usually susceptible to various buckling modes which often govern the ultimate failure of CFS members. When CFS members are exposed to a fire, not only the reduced mechanical properties will influence the buckling capacity of CFS members, but also the thermal strains which can lead additional stresses in loaded members. The buckling behaviour of the member can be analysed based on uniformly reduced material properties when the member is unprotected or uniformly protected surrounded by a fire that the temperature distribution within the member is uniform. However if the temperature distribution in a member is not uniform, which usually happens in walls and/or roof panels when CFS members are protected by plaster boards and exposed to fire on one side, the analysis of the member becomes very complicated since the mechanical properties such as Young’s modulus and yield strength and thermal strains vary within the member. This project has the aim of providing better understanding of the buckling performance of CFS channel members under non-uniform temperatures. The primary objective is to investigate the fire performance of plasterboard protected CFS members exposed to fire on one side, in the aspects of pre-buckling stress distribution, elastic buckling behaviour and nonlinear failure models. Heat transfer analyses of one-side protected CFS members have been conducted firstly to investigate the temperature distributions within the cross-section, which have been applied to the analytical study for the prediction of flexural buckling loads of CFS columns at elevated temperatures. A simplified numerical method based on the second order elastic – plastic analysis has also been proposed for the calculation of the flexural buckling load of CFS columns under non-uniform temperature distributions. The effects of temperature distributions and stress-strain relationships on the flexure buckling of CFS columns are discussed. Afterwards a modified finite strip method combined with the classical Fourier series solutions have been presented to investigate the elastic buckling behaviour of CFS members at elevated temperatures, in which the effects of temperatures on both strain and mechanical properties have been considered. The variations of the elastic buckling loads/moments, buckling modes and slenderness of CFS columns/beams with increasing temperatures have been examined. The finite element method is also used to carry out the failure analysis of one-side protected beams at elevated temperatures. The effects of geometric imperfection, stress-strain relationships and temperature distributions on the ultimate moment capacities of CFS beams under uniform and non-uniform temperature distributions are examined. At the end the direct strength method based design methods have been discussed and corresponding recommendations for the designing of CFS beams at elevated temperatures are presented. This thesis has contributed to improve the knowledge of the buckling and failure behaviour of CFS members at elevated temperatures, and the essential data provided in the numerical studies has laid the foundation for further design-oriented studies.

APA, Harvard, Vancouver, ISO, and other styles

14

Wanniarachchi, Somadasa. "Flexural behaviour and design of cold-formed steel beams with rectangular hollow flanges." Thesis, Queensland University of Technology, 2005. https://eprints.qut.edu.au/29810/1/Somadasa_Wanniarachchi_Thesis.pdf.

Full text

Abstract:

Until recently, the hot-rolled steel members have been recognized as the most popular and widely used steel group, but in recent times, the use of cold-formed high strength steel members has rapidly increased. However, the structural behavior of light gauge high strength cold-formed steel members characterized by various buckling modes is not yet fully understood. The current cold-formed steel sections such as C- and Z-sections are commonly used because of their simple forming procedures and easy connections, but they suffer from certain buckling modes. It is therefore important that these buckling modes are either delayed or eliminated to increase the ultimate capacity of these members. This research is therefore aimed at developing a new cold-formed steel beam with two torsionally rigid rectangular hollow flanges and a slender web formed using intermittent screw fastening to enhance the flexural capacity while maintaining a minimum fabrication cost. This thesis describes a detailed investigation into the structural behavior of this new Rectangular Hollow Flange Beam (RHFB), subjected to flexural action The first phase of this research included experimental investigations using thirty full scale lateral buckling tests and twenty two section moment capacity tests using specially designed test rigs to simulate the required loading and support conditions. A detailed description of the experimental methods, RHFB failure modes including local, lateral distortional and lateral torsional buckling modes, and moment capacity results is presented. A comparison of experimental results with the predictions from the current design rules and other design methods is also given. The second phase of this research involved a methodical and comprehensive investigation aimed at widening the scope of finite element analysis to investigate the buckling and ultimate failure behaviours of RHFBs subjected to flexural actions. Accurate finite element models simulating the physical conditions of both lateral buckling and section moment capacity tests were developed. Comparison of experimental and finite element analysis results showed that the buckling and ultimate failure behaviour of RHFBs can be simulated well using appropriate finite element models. Finite element models simulating ideal simply supported boundary conditions and a uniform moment loading were also developed in order to use in a detailed parametric study. The parametric study results were used to review the current design rules and to develop new design formulae for RHFBs subjected to local, lateral distortional and lateral torsional buckling effects. Finite element analysis results indicate that the discontinuity due to screw fastening has a noticeable influence only for members in the intermediate slenderness region. Investigations into different combinations of thicknesses in the flange and web indicate that increasing the flange thickness is more effective than web thickness in enhancing the flexural capacity of RHFBs. The current steel design standards, AS 4100 (1998) and AS/NZS 4600 (1996) are found sufficient to predict the section moment capacity of RHFBs. However, the results indicate that the AS/NZS 4600 is more accurate for slender sections whereas AS 4100 is more accurate for compact sections. The finite element analysis results further indicate that the current design rules given in AS/NZS 4600 is adequate in predicting the member moment capacity of RHFBs subject to lateral torsional buckling effects. However, they were inadequate in predicting the capacities of RHFBs subject to lateral distortional buckling effects. This thesis has therefore developed a new design formula to predict the lateral distortional buckling strength of RHFBs. Overall, this thesis has demonstrated that the innovative RHFB sections can perform well as economically and structurally efficient flexural members. Structural engineers and designers should make use of the new design rules and the validated existing design rules to design the most optimum RHFB sections depending on the type of applications. Intermittent screw fastening method has also been shown to be structurally adequate that also minimises the fabrication cost. Product manufacturers and builders should be able to make use of this in their applications.

APA, Harvard, Vancouver, ISO, and other styles

15

Wanniarachchi, Somadasa. "Flexural behaviour and design of cold-formed steel beams with rectangular hollow flanges." Queensland University of Technology, 2005. http://eprints.qut.edu.au/29810/.

Full text

Abstract:

Until recently, the hot-rolled steel members have been recognized as the most popular and widely used steel group, but in recent times, the use of cold-formed high strength steel members has rapidly increased. However, the structural behavior of light gauge high strength cold-formed steel members characterized by various buckling modes is not yet fully understood. The current cold-formed steel sections such as C- and Z-sections are commonly used because of their simple forming procedures and easy connections, but they suffer from certain buckling modes. It is therefore important that these buckling modes are either delayed or eliminated to increase the ultimate capacity of these members. This research is therefore aimed at developing a new cold-formed steel beam with two torsionally rigid rectangular hollow flanges and a slender web formed using intermittent screw fastening to enhance the flexural capacity while maintaining a minimum fabrication cost. This thesis describes a detailed investigation into the structural behavior of this new Rectangular Hollow Flange Beam (RHFB), subjected to flexural action The first phase of this research included experimental investigations using thirty full scale lateral buckling tests and twenty two section moment capacity tests using specially designed test rigs to simulate the required loading and support conditions. A detailed description of the experimental methods, RHFB failure modes including local, lateral distortional and lateral torsional buckling modes, and moment capacity results is presented. A comparison of experimental results with the predictions from the current design rules and other design methods is also given. The second phase of this research involved a methodical and comprehensive investigation aimed at widening the scope of finite element analysis to investigate the buckling and ultimate failure behaviours of RHFBs subjected to flexural actions. Accurate finite element models simulating the physical conditions of both lateral buckling and section moment capacity tests were developed. Comparison of experimental and finite element analysis results showed that the buckling and ultimate failure behaviour of RHFBs can be simulated well using appropriate finite element models. Finite element models simulating ideal simply supported boundary conditions and a uniform moment loading were also developed in order to use in a detailed parametric study. The parametric study results were used to review the current design rules and to develop new design formulae for RHFBs subjected to local, lateral distortional and lateral torsional buckling effects. Finite element analysis results indicate that the discontinuity due to screw fastening has a noticeable influence only for members in the intermediate slenderness region. Investigations into different combinations of thicknesses in the flange and web indicate that increasing the flange thickness is more effective than web thickness in enhancing the flexural capacity of RHFBs. The current steel design standards, AS 4100 (1998) and AS/NZS 4600 (1996) are found sufficient to predict the section moment capacity of RHFBs. However, the results indicate that the AS/NZS 4600 is more accurate for slender sections whereas AS 4100 is more accurate for compact sections. The finite element analysis results further indicate that the current design rules given in AS/NZS 4600 is adequate in predicting the member moment capacity of RHFBs subject to lateral torsional buckling effects. However, they were inadequate in predicting the capacities of RHFBs subject to lateral distortional buckling effects. This thesis has therefore developed a new design formula to predict the lateral distortional buckling strength of RHFBs. Overall, this thesis has demonstrated that the innovative RHFB sections can perform well as economically and structurally efficient flexural members. Structural engineers and designers should make use of the new design rules and the validated existing design rules to design the most optimum RHFB sections depending on the type of applications. Intermittent screw fastening method has also been shown to be structurally adequate that also minimises the fabrication cost. Product manufacturers and builders should be able to make use of this in their applications.

APA, Harvard, Vancouver, ISO, and other styles

16

Bathon, Leander Anton. "Probabilistic Determination of Failure Load Capacity Variations for Lattice Type Structures Based on Yield Strength Variations including Nonlinear Post-Buckling Member Performance." PDXScholar, 1992. https://pdxscholar.library.pdx.edu/open_access_etds/1225.

Full text

Abstract:

With the attempt to achieve the optimum in analysis and design, the technological global knowledge base grows more and more. Engineers all over the world continuously modify and innovate existing analysis methods and design procedures to perform the same task more efficiently and with better results. In the field of complex structural analysis many researchers pursue this challenging task. The complexity of a lattice type structure is caused by numerous parameters: the nonlinear member performance of the material, the statistical variation of member load capacities, the highly indeterminate structural composition, etc. In order to achieve a simulation approach which represents the real world problem more accurately, it is necessary to develop technologies which include these parameters in the analysis. One of the new technologies is the first order nonlinear analysis of lattice type structures including the after failure response of individual members. Such an analysis is able to predict the failure behavior of a structural system under ultimate loads more accurately than the traditionally used linear elastic analysis or a classical first order nonlinear analysis. It is an analysis procedure which can more accurately evaluate the limit-state of a structural system. The Probability Based Analysis (PBA) is a new technology. It provides the user with a tool to analyze structural systems based on statistical variations in member capacities. Current analysis techniques have shown that structural failure is sensitive to member capacity. The combination of probability based analysis and the limit-state analysis will give the engineer the capability to establish a failure load distribution based on the limit-state capacity of the structure. This failure load distribution which gives statistical properties such as mean and variance improves the engineering judgment. The mean shows the expected value or the mathematical expectation of the failure load. The variance is a tool to measure the variability of the failure load distribution. Based on a certain load case, a small variance will indicate that a few members cause the tower failure over and over again; the design is unbalanced. A large variance will indicate that many different members caused the tower failure. The failure load distribution helps in comparing and evaluating actual test results versus analytical results by locating an actual test among the possible failure loads of a tower series. Additionally, the failure load distribution allows the engineer to calculate exclusion limits which are a measure of the probability of success, or conversely the probability of failure for a given load condition. The exclusion limit allows engineers to redefine their judgement on safety and usability of transmission towers. Existing transmission towers can be reanalyzed using this PBA and upgraded based on a given exclusion limit for a chosen tower capacity increase according to the elastic analysis from which the tower was designed. New transmission towers can be analyzed based on the actual yield strength data and their nonlinear member performances. Based on this innovative analysis the engineer is able to improve tower design by using a tool which represents the real world behavior of steel transmission towers more accurately. Consequently it will improve structural safety and reduce cost.

APA, Harvard, Vancouver, ISO, and other styles

17

Siahaan, Ropalin. "Structural behaviour and design of rivet fastened rectangular hollow flange channel beams." Thesis, Queensland University of Technology, 2017. https://eprints.qut.edu.au/106913/1/Ropalin_Siahaan_Thesis.pdf.

Full text

Abstract:

This thesis presents a study into the structural behaviour and design of the innovative rivet fastened Rectangular Hollow Flange Channel Beams (RHFCB). The RHFCB utilizes the inexpensive self-pierce rivet fastening in its fabrication, providing cost effective structural solutions in floor systems. The first part of the thesis focuses on the section moment capacities of the beams subject to local buckling effects while the second part investigates the member moment capacities of intermediate span beams subject to the unique lateral distortional buckling effects. Each part involves experimental investigations, advanced finite element analyses, parametric studies and design recommendations.

APA, Harvard, Vancouver, ISO, and other styles

18

Čížková, Markéta. "Analýza poškození dopravního letounu při teroristickém útoku." Master's thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2021. http://www.nusl.cz/ntk/nusl-443754.

Full text

Abstract:

In its theoretical part, the diploma thesis deals with the reasons leading to terrorist attacks and a brief list of some attacks on aircraft. It also focuses on the aircraft as the target of a terrorist attack, especially the aircraft kite as the major researched part. The conclusion of the theoretical part summarizes a list of types of aircraft fuselage structures in respect of design solutions for load transfer. The practical part determines the extent of damage caused by a missile with a fragmentation warhead. This scope is then applied to the illustrative case. In the following chapters, the calculation of the critical force of a panel loaded with pressure depends on the different nature and extent of damage. Then the work highlights the evaluation of the obtained results, which are also summarized in the conclusions of the work.

APA, Harvard, Vancouver, ISO, and other styles

19

Gustavsson, Victor, and Hagenius Fabian. "En kapacitetsjämförelse mellan stålförstärktaträbalkar, limträ och konstruktionsvirke." Thesis, Tekniska Högskolan, Högskolan i Jönköping, JTH, Byggnadsteknik och belysningsvetenskap, 2019. http://urn.kb.se/resolve?urn=urn:nbn:se:hj:diva-45418.

Full text

Abstract:

Purpose: Throughout the years numerous studies have been made that concludes thatcombining steel and wood results in improved strength. Under optimal conditions woodis an effective structural material, as it’s both cheap and durable. Steel on the other handunder right circumstances has considerably higher strength than wood. To combinewood and steel has over the last years gathered more attention. Studies shows thathybrid structures can lead to an economical advantage when building multiple storeybuildings, as it can replace or complete pure steel frames. The purpose of this paper isto increase the knowledge and understanding of how steel and wood cooperate and tofind out the advantages and disadvantages of using a flitched beam, as well as compareit’s strength to structural wood and glulam.Method: The paper comprises a quantitative study with two different kinds of datacollection methods, Literature studies and calculations. The literature study consists ofscientific papers and papers published by known institutions and will help the paperanswer the first issue. The calculations has been made with the help of Tekla Tedds,which follows the Eurocode design principles. Which will help the authors answer bothof the papers issues.Findings: The paper has found that the flitch beam has improved strength overstructural wood and glulam, but a significantly higher price. The flitch beam also has amuch higher self weight than structural wood and glulam. The flitch beam can also spanlonger than structural wood and glulam with the same applied load.Implications: The study have concluded that it’s hard to motivate the usage of flitchedbeams in floor designs as they have such high price. The flitch beam has higher strengththan both structural wood and glulam. Which makes the flitch beam a good option asload bearing beam that requires slim dimensions. The added strength of the flitch beamcan motivate the high price under the right circumstances.Limitations: The paper has limited the calculations to an enclosed environment andwill not take moisture or any other type of exposure in to account, As a dry indoorenvironment is optimal for both steel and wood. The calculations the paper uses arebased on Eurocode and all other forms of dimension principles will not be taken intoaccount.
Syfte: Genom åren har forskning gjorts som tyder på att när man kombinerar stål ochträ kommer det bidra till en ökad hållfasthet. Under optimala förhållande är trä ettotroligt effektivt och bra alternativ inom byggande då det är billigt och tåligt. Närstålbalkar däremot placeras i optimala förhållande kan de bibehåll betydligt mer ochstörre krafter än vad trävirke kan göra. Att kombinera stål och trä har de senaste årethaft ett ökat intresse. Studier visar att hybridbalkar kan vara till stor ekonomisk fördelvid byggnation av flervåningshus, då det kan ersätta eller komplettera rena stålstommar.Syftet med arbete är att öka kunskapen och förståelsen för hur stål och trä samverkarsamt ta reda på för och nackdelar hos de stålförstärkta träbalkarna samt jämföra deraslastkapacitet med konstruktionsträ- och limträbalkar.Metod: Arbetet omfattar en kvantitativ studie där två typer av datainsamlingsmetoderhar använts. Dessa två typer är beräkningar samt litteraturstudier. Litteraturstudienbestår av vetenskapliga artiklar som har hjälpt besvara en av frågeställningarna.Beräkningarna har använts för att besvara båda frågeställningarna, de har gjorts idimensioneringsprogrammet Tekla tedds som följer alla Eurocodes beräknings- ochdimensioneringsregler.Resultat: Resultaten visar på att den stålförstärkta träbalken har högre kapacitet änlimträ och konstruktionsvirke, både med hänsyn till nedböjning och brott men betydligthögre pris och egentyngd. Den stålförstärkta träbalken klarar även av längrespännvidder vid samma belastning.Konsekvenser: Utifrån de resultat rapporten kommit fram till är det svårmotiverat attanvända sig av de stålförstärkta balkarna i bjälklag på grund av det höga priset Denstålförstärkta träbalken klarar dock av högre laster än vad konstruktionsvirke och limträgör, vilket kan göra balken användbar som avväxlingsbalk. Att använda denstålförstärkta träbalken som avväxlingsbalk kan motivera det höga priset då den kanhålla mindre dimensioner än limträ och konstruktionsvirke vilket kan vara önskvärt iolika sammanhang.Begränsningar: De begränsningar som sattes för rapporten var att utesluta alla typerav miljörisker på balkarna som tillexempel fukt och solljus vid beräkningarna, då entorrmiljö är en optimal miljö för både trä och stål. Beräkningarna som arbetet baseraspå grundar sig på Eurocodes dimensioneringsregler. Andra typer av dimensioneringsprinciper har uteslutits.

APA, Harvard, Vancouver, ISO, and other styles

20

Sivaprakasam, Thananjayan. "Structural behaviour and design of aluminium facade mullions under wind actions." Thesis, Queensland University of Technology, 2019. https://eprints.qut.edu.au/135457/1/Thananjayan_Sivaprakasam_Thesis.pdf.

Full text

Abstract:

This research has significantly advanced the knowledge and understanding of the structural behaviour and design of vertical load bearing members of aluminium facades subject to wind actions, based on full-scale wind pressure tests and extensive advanced numerical simulations. It has shown that the design approaches used in the industry may result in either conservative or unsafe designs of vertical load bearing members, and thus developed improved design guidelines. Further, it has demonstrated that advanced numerical simulations can be used for economical designs of these facade members.

APA, Harvard, Vancouver, ISO, and other styles

21

Anapayan, Tharmarajah. "Flexural behaviour and design of hollow flange steel beams." Thesis, Queensland University of Technology, 2010. https://eprints.qut.edu.au/36210/1/Tharmarajah_Anapayan_Thesis.pdf.

Full text

Abstract:

The LiteSteel Beam (LSB) is a new hollow flange channel section developed by OneSteel Australian Tube Mills using a patented Dual Electric Resistance Welding technique. The LSB has a unique geometry consisting of torsionally rigid rectangular hollow flanges and a relatively slender web. It is commonly used as rafters, floor joists and bearers and roof beams in residential, industrial and commercial buildings. It is on average 40% lighter than traditional hot-rolled steel beams of equivalent performance. The LSB flexural members are subjected to a relatively new Lateral Distortional Buckling mode, which reduces the member moment capacity. Unlike the commonly observed lateral torsional buckling of steel beams, lateral distortional buckling of LSBs is characterised by simultaneous lateral deflection, twist and web distortion. Current member moment capacity design rules for lateral distortional buckling in AS/NZS 4600 (SA, 2005) do not include the effect of section geometry of hollow flange beams although its effect is considered to be important. Therefore detailed experimental and finite element analyses (FEA) were carried out to investigate the lateral distortional buckling behaviour of LSBs including the effect of section geometry. The results showed that the current design rules in AS/NZS 4600 (SA, 2005) are over-conservative in the inelastic lateral buckling region. New improved design rules were therefore developed for LSBs based on both FEA and experimental results. A geometrical parameter (K) defined as the ratio of the flange torsional rigidity to the major axis flexural rigidity of the web (GJf/EIxweb) was identified as the critical parameter affecting the lateral distortional buckling of hollow flange beams. The effect of section geometry was then included in the new design rules using the new parameter (K). The new design rule developed by including this parameter was found to be accurate in calculating the member moment capacities of not only LSBs, but also other types of hollow flange steel beams such as Hollow Flange Beams (HFBs), Monosymmetric Hollow Flange Beams (MHFBs) and Rectangular Hollow Flange Beams (RHFBs). The inelastic reserve bending capacity of LSBs has not been investigated yet although the section moment capacity tests of LSBs in the past revealed that inelastic reserve bending capacity is present in LSBs. However, the Australian and American cold-formed steel design codes limit them to the first yield moment. Therefore both experimental and FEA were carried out to investigate the section moment capacity behaviour of LSBs. A comparison of the section moment capacity results from FEA, experiments and current cold-formed steel design codes showed that compact and non-compact LSB sections classified based on AS 4100 (SA, 1998) have some inelastic reserve capacity while slender LSBs do not have any inelastic reserve capacity beyond their first yield moment. It was found that Shifferaw and Schafer’s (2008) proposed equations and Eurocode 3 Part 1.3 (ECS, 2006) design equations can be used to include the inelastic bending capacities of compact and non-compact LSBs in design. As a simple design approach, the section moment capacity of compact LSB sections can be taken as 1.10 times their first yield moment while it is the first yield moment for non-compact sections. For slender LSB sections, current cold-formed steel codes can be used to predict their section moment capacities. It was believed that the use of transverse web stiffeners could improve the lateral distortional buckling moment capacities of LSBs. However, currently there are no design equations to predict the elastic lateral distortional buckling and member moment capacities of LSBs with web stiffeners under uniform moment conditions. Therefore, a detailed study was conducted using FEA to simulate both experimental and ideal conditions of LSB flexural members. It was shown that the use of 3 to 5 mm steel plate stiffeners welded or screwed to the inner faces of the top and bottom flanges of LSBs at third span points and supports provided an optimum web stiffener arrangement. Suitable design rules were developed to calculate the improved elastic buckling and ultimate moment capacities of LSBs with these optimum web stiffeners. A design rule using the geometrical parameter K was also developed to improve the accuracy of ultimate moment capacity predictions. This thesis presents the details and results of the experimental and numerical studies of the section and member moment capacities of LSBs conducted in this research. It includes the recommendations made regarding the accuracy of current design rules as well as the new design rules for lateral distortional buckling. The new design rules include the effects of section geometry of hollow flange steel beams. This thesis also developed a method of using web stiffeners to reduce the lateral distortional buckling effects, and associated design rules to calculate the improved moment capacities.

APA, Harvard, Vancouver, ISO, and other styles

22

Keerthan, Poologanathan. "Shear behaviour and design of LiteSteel beams." Thesis, Queensland University of Technology, 2010. https://eprints.qut.edu.au/36208/1/Poologanathan_Keerthan_Thesis.pdf.

Full text

Abstract:

OneSteel Australian Tube Mills has recently developed a new hollow flange channel cold-formed section, known as the LiteSteel Beam (LSB). The innovative LSB sections have the beneficial characteristics of torsionally rigid closed rectangular flanges combined with economical fabrication processes from a single strip of high strength steel. They combine the stability of hot-rolled steel sections with the high strength to weight ratio of conventional cold-formed steel sections. The LSB sections are commonly used as flexural members in residential, industrial and commercial buildings. In order to ensure safe and efficient designs of LSBs, many research studies have been undertaken on the flexural behaviour of LSBs. However, no research has been undertaken on the shear behaviour of LSBs. Therefore this thesis investigated the ultimate shear strength behaviour of LSBs with and without web openings including their elastic buckling and post-buckling characteristics using both experimental and finite element analyses, and developed accurate shear design rules. Currently the elastic shear buckling coefficients of web panels are determined by assuming conservatively that the web panels are simply supported at the junction between the web and flange elements. Therefore finite element analyses were conducted first to investigate the elastic shear buckling behaviour of LSBs to determine the true support condition at the junction between their web and flange elements. An equation for the higher elastic shear buckling coefficient of LSBs was developed and included in the shear capacity equations in the cold-formed steel structures code, AS/NZS 4600. Predicted shear capacities from the modified equations and the available experimental results demonstrated the improvements to the shear capacities of LSBs due to the presence of higher level of fixity at the LSB flange to web juncture. A detailed study into the shear flow distribution of LSB was also undertaken prior to the elastic buckling analysis study. The experimental study of ten LSB sections included 42 shear tests of LSBs with aspect ratios of 1.0 and 1.5 that were loaded at midspan until failure. Both single and back to back LSB arrangements were used. Test specimens were chosen such that all three types of shear failure (shear yielding, inelastic and elastic shear buckling) occurred in the tests. Experimental results showed that the current cold-formed steel design rules are very conservative for the shear design of LSBs. Significant improvements to web shear buckling occurred due to the presence of rectangular hollow flanges while considerable post-buckling strength was also observed. Experimental results were presented and compared with corresponding predictions from the current design rules. Appropriate improvements have been proposed for the shear strength of LSBs based on AISI (2007) design equations and test results. Suitable design rules were also developed under the direct strength method (DSM) format. This thesis also includes the shear test results of cold-formed lipped channel beams from LaBoube and Yu (1978a), and the new design rules developed based on them using the same approach used with LSBs. Finite element models of LSBs in shear were also developed to investigate the ultimate shear strength behaviour of LSBs including their elastic and post-buckling characteristics. They were validated by comparing their results with experimental test results. Details of the finite element models of LSBs, the nonlinear analysis results and their comparisons with experimental results are presented in this thesis. Finite element analysis results showed that the current cold-formed steel design rules are very conservative for the shear design of LSBs. They also confirmed other experimental findings relating to elastic and post-buckling shear strength of LSBs. A detailed parametric study based on validated experimental finite element model was undertaken to develop an extensive shear strength data base and was then used to confirm the accuracy of the new shear strength equations proposed in this thesis. Experimental and numerical studies were also undertaken to investigate the shear behaviour of LSBs with web openings. Twenty six shear tests were first undertaken using a three point loading arrangement. It was found that AS/NZS 4600 and Shan et al.'s (1997) design equations are conservative for the shear design of LSBs with web openings while McMahon et al.'s (2008) design equation are unconservative. Experimental finite element models of LSBs with web openings were then developed and validated by comparing their results with experimental test results. The developed nonlinear finite element model was found to predict the shear capacity of LSBs with web opening with very good accuracy. Improved design equations have been proposed for the shear capacity of LSBs with web openings based on both experimental and FEA parametric study results. This thesis presents the details of experimental and numerical studies of the shear behaviour and strength of LSBs with and without web openings and the results including the developed accurate design rules.

APA, Harvard, Vancouver, ISO, and other styles

23

Kinali, Kursat. "Seismic Fragility Assessment of Steel Frames in the Central and Eastern United States." Diss., Georgia Institute of Technology, 2007. http://hdl.handle.net/1853/14528.

Full text

Abstract:

The Central and Eastern United States (CEUS) is a region that is characterized by low frequency-high consequence seismic events such as the New Madrid sequence of 18111812. The infrequent nature of earthquakes in the region has led to a perception that the seismic risk in the area is low, and the current building stock reflects this perception. The majority of steel-framed buildings in the CEUS were designed without regard to seismic loads. Such frames possess limited seismic resistance, and may pose an unacceptable risk if a large earthquake were to occur in the region. A key ingredient of building performance and seismic risk assessment is the fragility, a term that describes the probability of failure to meet a performance objective as a function of demand on the system. The effects of uncertainties on building seismic performance can be displayed by a seismic fragility relationship. This fragility can be used in a conditional scenario-based seismic risk assessment or can be integrated with seismic hazard to obtain an estimate of annual or lifetime risk. The seismic fragility analyses in this study focus on steel frames that are typical of building construction in regions of infrequent seismicity; such frames have received little attention to date in building seismic risk assessment. Current steel building stock in Shelby Co., TN has been represented by five code-compliant model frames with different lateral force-resisting systems, i.e., braced-frames, partially-restrained moment frames and a rigid moment frame. The performance of model frames under certain hazard levels was assessed using fragility curves. Different rehabilitation methods were discussed and applied. Results indicate that PR frames behave better than expected and rehabilitated frames perform quite well even under severe earthquakes.

APA, Harvard, Vancouver, ISO, and other styles

24

Horák, Marek. "Pevnostní analýza nosníku s tenkou stojinou - vliv otvorů a tahového pole." Doctoral thesis, Vysoké učení technické v Brně. Fakulta strojního inženýrství, 2014. http://www.nusl.cz/ntk/nusl-234239.

Full text

Abstract:

In design of an aircraft structure, the great emphasis is placed on achieving high weight efficiency. This thesis is focused on the stress analysis of the spars with thin web with or without web openings, which is one of the most important parts of the airplane structures. In comparison with traditional spars or beams, which are widely used in civil engineering applications, the design of the beam with thin web is more complicated. Thesis contains useful information for analytical calculation of this type of spars and its verification using finite element method and experimental measurement.

APA, Harvard, Vancouver, ISO, and other styles

25

葛西, 昭., Akira Kasai, 健太木戸, Kenta Kido, 勉. 宇佐美, Tsutomu Usami, 尚彦渡辺, and Naohiko Watanabe. "多径間連続高架橋への制震ブレースの導入効果." 土木学会, 2005. http://hdl.handle.net/2237/8535.

Full text

APA, Harvard, Vancouver, ISO, and other styles

26

Dolamune, Kankanamge Nirosha. "Structural behaviour and design of cold-formed steel beams at elevated temperatures." Thesis, Queensland University of Technology, 2010. https://eprints.qut.edu.au/33221/1/Nirosha_Dolamune_Kankanamge_Thesis.pdf.

Full text

Abstract:

Cold-formed steel members are extensively used in the building construction industry, especially in residential, commercial and industrial buildings. In recent times, fire safety has become important in structural design due to increased fire damage to properties and loss of lives. However, past research into the fire performance of cold-formed steel members has been limited, and was confined to compression members. Therefore a research project was undertaken to investigate the structural behaviour of compact cold-formed steel lipped channel beams subject to inelastic local buckling and yielding, and lateral-torsional buckling effects under simulated fire conditions and associated section and member moment capacities. In the first phase of this research, an experimental study based on tensile coupon tests was undertaken to obtain the mechanical properties of elastic modulus and yield strength and the stress-strain relationship of cold-formed steels at uniform ambient and elevated temperatures up to 700oC. The mechanical properties deteriorated with increasing temperature and are likely to reduce the strength of cold-formed beams under fire conditions. Predictive equations were developed for yield strength and elastic modulus reduction factors while a modification was proposed for the stressstrain model at elevated temperatures. These results were used in the numerical modelling phases investigating the section and member moment capacities. The second phase of this research involved the development and validation of two finite element models to simulate the behaviour of compact cold-formed steel lipped channel beams subject to local buckling and yielding, and lateral-torsional buckling effects. Both models were first validated for elastic buckling. Lateral-torsional buckling tests of compact lipped channel beams were conducted at ambient temperature in order to validate the finite element model in predicting the non-linear ultimate strength behaviour. The results from this experimental study did not agree well with those from the developed experimental finite element model due to some unavoidable problems with testing. However, it highlighted the importance of magnitude and direction of initial geometric imperfection as well as the failure direction, and thus led to further enhancement of the finite element model. The finite element model for lateral-torsional buckling was then validated using the available experimental and numerical ultimate moment capacity results from past research. The third phase based on the validated finite element models included detailed parametric studies of section and member moment capacities of compact lipped channel beams at ambient temperature, and provided the basis for similar studies at elevated temperatures. The results showed the existence of inelastic reserve capacity for compact cold-formed steel beams at ambient temperature. However, full plastic capacity was not achieved by the mono-symmetric cold-formed steel beams. Suitable recommendations were made in relation to the accuracy and suitability of current design rules for section moment capacity. Comparison of member capacity results from finite element analyses with current design rules showed that they do not give accurate predictions of lateral-torsional buckling capacities at ambient temperature and hence new design rules were developed. The fourth phase of this research investigated the section and member moment capacities of compact lipped channel beams at uniform elevated temperatures based on detailed parametric studies using the validated finite element models. The results showed the existence of inelastic reserve capacity at elevated temperatures. Suitable recommendations were made in relation to the accuracy and suitability of current design rules for section moment capacity in fire design codes, ambient temperature design codes as well as those proposed by other researchers. The results showed that lateral-torsional buckling capacities are dependent on the ratio of yield strength and elasticity modulus reduction factors and the level of non-linearity in the stress-strain curves at elevated temperatures in addition to the temperature. Current design rules do not include the effects of non-linear stress-strain relationship and therefore their predictions were found to be inaccurate. Therefore a new design rule that uses a nonlinearity factor, which is defined as the ratio of the limit of proportionality to the yield stress at a given temperature, was developed for cold-formed steel beams subject to lateral-torsional buckling at elevated temperatures. This thesis presents the details and results of the experimental and numerical studies conducted in this research including a comparison of results with predictions using available design rules. It also presents the recommendations made regarding the accuracy of current design rules as well as the new developed design rules for coldformed steel beams both at ambient and elevated temperatures.

APA, Harvard, Vancouver, ISO, and other styles

27

Baxant, Radek. "Řešení stability prutových konstrukcí." Master's thesis, Vysoké učení technické v Brně. Fakulta stavební, 2015. http://www.nusl.cz/ntk/nusl-227507.

Full text

Abstract:

This diploma thesis deals with the subject of slenderness bars’ stability assessment, especially in the steel structures. Before the assessment of bars in the frame constructions, we search for the influence of the computational model’s settings on the final result. The initial geometrical imperfections are examined on the model of Euler’s bar. The influence of the rigidity of girders on the poles’ buckling length is examined on the basic frame construction. The buckling lengths are assessed in the comparison with the figures we got from the statistical tables and the computational software. The influence of construction’s initial tilt and its replacement by the system of outer forces is examined on the frame structure. Three-hinged frame structure with variable cross-section member is designed then and the influence of non-linear calculations on the inner forces is studied. In the complex frame assessment, the influence of the number of parts of variable cross-section member on the bars’ buckling length is examined.

APA, Harvard, Vancouver, ISO, and other styles

28

Baleshan, Balachandren. "Numerical and experimental studies of cold-formed steel floor systems under standard fire conditions." Thesis, Queensland University of Technology, 2012. https://eprints.qut.edu.au/53096/1/Balachandren_Baleshan_Thesis.pdf.

Full text

Abstract:

Light gauge cold-formed steel frame (LSF) structures are increasingly used in industrial, commercial and residential buildings because of their non-combustibility, dimensional stability, and ease of installation. A floor-ceiling system is an example of its applications. LSF floor-ceiling systems must be designed to serve as fire compartment boundaries and provide adequate fire resistance. Fire rated floor-ceiling assemblies formed with new materials and construction methodologies have been increasingly used in buildings. However, limited research has been undertaken in the past and hence a thorough understanding of their fire resistance behaviour is not available. Recently a new composite panel in which an external insulation layer is used between two plasterboards has been developed at QUT to provide a higher fire rating to LSF floors under standard fire conditions. But its increased fire rating could not be determined using the currently available design methods. Research on LSF floor systems under fire conditions is relatively recent and the behaviour of floor joists and other components in the systems is not fully understood. The present design methods thus require the use of expensive fire protection materials to protect them from excessive heat increase during a fire. This leads to uneconomical and conservative designs. Fire rating of these floor systems is provided simply by adding more plasterboard sheets to the steel joists and such an approach is totally inefficient. Hence a detailed fire research study was undertaken into the structural and thermal performance of LSF floor systems including those protected by the new composite panel system using full scale fire tests and extensive numerical studies. Experimental study included both the conventional and the new steel floor-ceiling systems under structural and fire loads using a gas furnace designed to deliver heat in accordance with the standard time- temperature curve in AS 1530.4 (SA, 2005). Fire tests included the behavioural and deflection characteristics of LSF floor joists until failure as well as related time-temperature measurements across the section and along the length of all the specimens. Full scale fire tests have shown that the structural and thermal performance of externally insulated LSF floor system was superior than traditional LSF floors with or without cavity insulation. Therefore this research recommends the use of the new composite panel system for cold-formed LSF floor-ceiling systems. The numerical analyses of LSF floor joists were undertaken using the finite element program ABAQUS based on the measured time-temperature profiles obtained from fire tests under both steady state and transient state conditions. Mechanical properties at elevated temperatures were considered based on the equations proposed by Dolamune Kankanamge and Mahendran (2011). Finite element models were calibrated using the full scale test results and used to further provide a detailed understanding of the structural fire behaviour of the LSF floor-ceiling systems. The models also confirmed the superior performance of the new composite panel system. The validated model was then used in a detailed parametric study. Fire tests and the numerical studies showed that plasterboards provided sufficient lateral restraint to LSF floor joists until their failure. Hence only the section moment capacity of LSF floor joists subjected to local buckling effects was considered in this research. To predict the section moment capacity at elevated temperatures, the effective section modulus of joists at ambient temperature is generally considered adequate. However, this research has shown that it leads to considerable over- estimation of the local buckling capacity of joist subject to non-uniform temperature distributions under fire conditions. Therefore new simplified fire design rules were proposed for LSF floor joist to determine the section moment capacity at elevated temperature based on AS/NZS 4600 (SA, 2005), NAS (AISI, 2007) and Eurocode 3 Part 1.3 (ECS, 2006). The accuracy of the proposed fire design rules was verified with finite element analysis results. A spread sheet based design tool was also developed based on these design rules to predict the failure load ratio versus time, moment capacity versus time and temperature for various LSF floor configurations. Idealised time-temperature profiles of LSF floor joists were developed based on fire test measurements. They were used in the detailed parametric study to fully understand the structural and fire behaviour of LSF floor panels. Simple design rules were also proposed to predict both critical average joist temperatures and failure times (fire rating) of LSF floor systems with various floor configurations and structural parameters under any given load ratio. Findings from this research have led to a comprehensive understanding of the structural and fire behaviour of LSF floor systems including those protected by the new composite panel, and simple design methods. These design rules were proposed within the guidelines of the Australian/New Zealand, American and European cold- formed steel structures standard codes of practice. These may also lead to further improvements to fire resistance through suitable modifications to the current composite panel system.

APA, Harvard, Vancouver, ISO, and other styles

29

Wilkinson, Timothy James. "The Plastic Behaviour of Cold-Formed Rectangular Hollow Sections." University of Sydney. Department of Civil Engineering, 2000. http://hdl.handle.net/2123/843.

Full text

Abstract:

The aim of this thesis is to assess the suitability of cold-formed rectangular hollow sections (RHS) for plastic design. The project involved an extensive range of tests on cold-formed Grade C350 and Grade C450 (DuraGal) RHS beams, joints and frames. A large number of finite element analyses was also carried out on models of RHS beams. The conclusion is that cold- formed RHS can be used in plastic design, but stricter element slenderness (b/t) limits and consideration of the connections, are required. Further research, particularly into the effect of axial compression on element slenderness limits, is required before changes to current design rules can be finalised. Bending tests were performed on cold-formed RHS to examine the web and flange slenderness required to maintain the plastic moment for a large enough rotation suitable for plastic design. The major conclusions of the beam tests were: (i) Some sections which are classified as Compact or Class 1 by current steel design specifications do not maintain plastic rotations considered sufficient for plastic design. (ii) The current design philosophy, in which flange and web slenderness limits are independent, is inappropriate. An interaction formula is required, and simple formulations are proposed for RHS. Connection tests were performed on various types of knee joints in RHS, suitable for the column - rafter connection in a portal frame. The connection types investigated were welded stiffened and unstiffened rigid knee connections, bolted plate knee joints, and welded and bolted internal sleeve knee joints, for use in RHS portal frames. The ability of the connections to act as plastic hinges in a portal frame was investigated. The most important finding of the joint tests was the unexpected fracture of the cold-formed welded connections under opening moment before significant plastic rotations occurred. The use of an internal sleeve moved the plastic hinge in the connection away from the connection centre- line thus eliminating the need for the weld between the RHS, or the RHS and the stiffening plate, to carry the majority of the load. The internal sleeve connections were capable of sustaining the plastic moment for large rotations considered suitable for plastic design. Tests on pinned-base portal frames were also performed. There were three separate tests, with two different ratios of vertical to horizontal point loads, simulating gravity and horizontal wind loads. Two grades of steel were used for comparison. The aims of the tests were to examine if a plastic collapse mechanism could form in a cold-formed RHS frame, and to investigate if plastic design was suitable for such frames. In each frame, two regions of highly concentrated curvature were observed before the onset of local buckling, which indicated the formation of plastic hinges and a plastic collapse mechanism. An advanced plastic zone structural analysis which accounted for second order effects, material non-linearity and member imperfections slightly overestimated the strength of the frames. The analysis slightly underestimated the deflections, and hence the magnitude of the second order effects. A second order plastic zone analysis, which did not account for the effects of structural imperfections, provided the best estimates of the strengths of the frames, but also underestimated the deflections. While cold-formed RHS did not satisfy the material ductility requirements specified for plastic design in some current steel design standards, plastic hinges and plastic collapse mechanisms formed. This suggests that the restriction on plastic design for cold-formed RHS based on insufficient material ductility is unnecessary, provided that the connections are suitable for plastic hinge formation, if required. A large number of finite element analyses were performed to simulate the bending tests summarised above, and to examine various parameters not studied in the experimental investigation. To simulate the experimental rotation capacity of the RHS beams, a sinusoidally varying longitudinal local imperfection was prescribed. The finite element analysis determined similar trends as observed experimentally, namely that the rotation capacity depended on both the web slenderness and flange slenderness, and that for a given section aspect ratio, the relationship between web slenderness and rotation capacity was non-linear. The main finding of the finite element study was that the size of the imperfections had an unexpectedly large influence on the rotation capacity. Larger imperfections were required in the more slender sections to simulate the experimental results. There should be further investigation into the effect of varying material properties on rotation capacity.

APA, Harvard, Vancouver, ISO, and other styles

30

Wilkinson, Timothy James. "The Plastic Behaviour of Cold-Formed Rectangular Hollow Sections." Thesis, The University of Sydney, 1999. http://hdl.handle.net/2123/843.

Full text

Abstract:

The aim of this thesis is to assess the suitability of cold-formed rectangular hollow sections (RHS) for plastic design. The project involved an extensive range of tests on cold-formed Grade C350 and Grade C450 (DuraGal) RHS beams, joints and frames. A large number of finite element analyses was also carried out on models of RHS beams. The conclusion is that cold- formed RHS can be used in plastic design, but stricter element slenderness (b/t) limits and consideration of the connections, are required. Further research, particularly into the effect of axial compression on element slenderness limits, is required before changes to current design rules can be finalised. Bending tests were performed on cold-formed RHS to examine the web and flange slenderness required to maintain the plastic moment for a large enough rotation suitable for plastic design. The major conclusions of the beam tests were: (i) Some sections which are classified as Compact or Class 1 by current steel design specifications do not maintain plastic rotations considered sufficient for plastic design. (ii) The current design philosophy, in which flange and web slenderness limits are independent, is inappropriate. An interaction formula is required, and simple formulations are proposed for RHS. Connection tests were performed on various types of knee joints in RHS, suitable for the column - rafter connection in a portal frame. The connection types investigated were welded stiffened and unstiffened rigid knee connections, bolted plate knee joints, and welded and bolted internal sleeve knee joints, for use in RHS portal frames. The ability of the connections to act as plastic hinges in a portal frame was investigated. The most important finding of the joint tests was the unexpected fracture of the cold-formed welded connections under opening moment before significant plastic rotations occurred. The use of an internal sleeve moved the plastic hinge in the connection away from the connection centre- line thus eliminating the need for the weld between the RHS, or the RHS and the stiffening plate, to carry the majority of the load. The internal sleeve connections were capable of sustaining the plastic moment for large rotations considered suitable for plastic design. Tests on pinned-base portal frames were also performed. There were three separate tests, with two different ratios of vertical to horizontal point loads, simulating gravity and horizontal wind loads. Two grades of steel were used for comparison. The aims of the tests were to examine if a plastic collapse mechanism could form in a cold-formed RHS frame, and to investigate if plastic design was suitable for such frames. In each frame, two regions of highly concentrated curvature were observed before the onset of local buckling, which indicated the formation of plastic hinges and a plastic collapse mechanism. An advanced plastic zone structural analysis which accounted for second order effects, material non-linearity and member imperfections slightly overestimated the strength of the frames. The analysis slightly underestimated the deflections, and hence the magnitude of the second order effects. A second order plastic zone analysis, which did not account for the effects of structural imperfections, provided the best estimates of the strengths of the frames, but also underestimated the deflections. While cold-formed RHS did not satisfy the material ductility requirements specified for plastic design in some current steel design standards, plastic hinges and plastic collapse mechanisms formed. This suggests that the restriction on plastic design for cold-formed RHS based on insufficient material ductility is unnecessary, provided that the connections are suitable for plastic hinge formation, if required. A large number of finite element analyses were performed to simulate the bending tests summarised above, and to examine various parameters not studied in the experimental investigation. To simulate the experimental rotation capacity of the RHS beams, a sinusoidally varying longitudinal local imperfection was prescribed. The finite element analysis determined similar trends as observed experimentally, namely that the rotation capacity depended on both the web slenderness and flange slenderness, and that for a given section aspect ratio, the relationship between web slenderness and rotation capacity was non-linear. The main finding of the finite element study was that the size of the imperfections had an unexpectedly large influence on the rotation capacity. Larger imperfections were required in the more slender sections to simulate the experimental results. There should be further investigation into the effect of varying material properties on rotation capacity.

APA, Harvard, Vancouver, ISO, and other styles

31

Jatheeshan, Varathananthan. "Numerical and experimental studies of cold-formed steel floor systems made of hollow flange section joists in fire." Thesis, Queensland University of Technology, 2015. https://eprints.qut.edu.au/120145/1/Varathananthan_Jatheeshan_Thesis.pdf.

Full text

Abstract:

The cold-formed steel utilization in buildings has increased globally due to its higher strength to weight ratio, ease of transportation and rapid erection and dismantlement. However, cold-formed steel buildings must be designed with adequate Fire Resistance Ratings (FRR). Hence cold-formed Light gauge Steel Frames (LSF) are assembled using channel sections and lined with fire resistive plasterboards to provide load-bearing wall and floor systems. There is an industry need to develop LSF floor systems with improved FRR. Adding multiple layers of plasterboard to increase the FRR of LSF floor systems is not an efficient method. Past research has focused on investigating the behaviour of LSF floor systems made of Lipped Channel Section (LCS) joists. No attempt has been made to use an improved joist section in LSF floor systems. The Hollow Flange Sections (HFS) with torsionally rigid hollow flanges and no free edges have higher local and lateral distortional buckling capacities than the conventional LCSs. This research focuses on investigating the structural and fire performance of LSF floor systems made of HFS joists with a goal to improve their FRRs. Four full scale standard fire tests were undertaken on non-insulated dual and single plasterboard lined LSF floor panels and cavity insulated dual plasterboard lined floor panel made of welded HFS joists known as LiteSteel beams (LSB). Fire tests of these panels undertaken for varying load ratios provided valuable results, which included failure times, joist temperatures and modes, and deflection versus time curves. The floor panels failed due to the section failures of joists. Both non-insulated and cavity insulated LSF floors made of LSB joists showed a significant improvement in the FRRs in comparison to Baleshan's (2012) results for LSF floors made of LCS joists. Another experimental study was undertaken to determine the elevated temperature mechanical properties of the steel used in LSB web and flange elements. The mechanical property reduction variation of LSB steel elements was found to be quite different to that of normal cold-formed steels and was even dissimilar amongst them. The yield strength reduction factors of Eurocode 3 Part 1.2 (ECS, 2005) were proposed for the web elements since they closely followed them whereas a new yield strength reduction factor model was proposed for the flange elements. An identical variation was proposed for the elastic modulus reduction factors of both web and flange elements. Suitable modifications were made to Dolamune Kankanamge and Mahendran's (2011) stress-strain model for improved predictions of LSB web and flange elements' stress-strain curves. A Finite Element (FE) model of an individual simply supported LSB joist was developed and validated using the cold-formed steel design standards and Anapayan et al.'s (2011b) section moment capacity test results. By using the accurate mechanical property reduction factors of LSB steel elements, the FE model was then extended to simulate the full scale fire tests. Finite element analyses (FEA) showed reasonably good agreements in terms of failure times, temperatures and modes, and the mid-span deflection versus time curves. Such good agreements verified the accuracy of the developed FE model to simulate the LSF floor panels made of HFS joists under fire conditions. Thermal FE models of LSF floor systems made of HFS joists were then developed and the time-temperature profiles were compared with the fire test results. They showed better agreements for Tests 1 and 4 whereas there were some discrepancies for Tests 2 and 3. Thermal FEA results obtained using appropriate thermal properties of plywood showed a reasonably good agreement with Baleshan's (2012) fire test results. Parametric studies using the validated model showed that joist section depth and profile had no significant impact on the thermal performance of LSF floor systems whereas steel joist thickness had a significant influence. An extensive FEA based parametric study was then undertaken to investigate the effects of joist thickness, depth, section profile, steel grade and mechanical property reduction factors, and web openings on the structural and fire performances (FRR) of LSF floor systems. Steel joist thickness significantly influenced the FRR of LSF floor systems due to different temperature developments in the steels for varying thicknesses. Joist section depth, section profile and web openings had no significant impact on the FRRs of LSF floor systems. Steel type affected the FRRs of LSF floor systems significantly due to different mechanical property reduction factors, especially different yield strength reduction factors. It was shown that Baleshan's (2012) critical average joist temperature method can be used to determine the FRR of non-insulated dual and single plasterboard lined floor panels made of HFS joists. However, it can be used for cavity insulated floor panels when the load ratio is less than 0.3. Fire test and FEA results showed that LSF floor panels made of LSB joists gave higher FRRs due to improved elevated temperature mechanical properties of LSB plate elements and lower temperature development due to thicker joists. Fire design rules were developed to predict the FRRs of LSF floor systems made of HFS joists based on Eurocode 3 Part 1.3 (ECS, 2006), AS/NZS 4600 (SA, 2005) and Direct Strength Method (DSM). For this purpose, Baleshan's (2012) three fire design rules of LCS joists were used and suitable modifications were made in order to use them for HFS joists. A good agreement was observed between the FRR predictions using two design methods and FEA, and thus they were recommended. In addition, the FRR predictions of HFS joists using the fire design method developed based on DSM were modestly conservative and therefore they were also recommended. Finally, the spread sheet based design tool was developed to undertake the complex calculations in predicting the FRR of LSF floors made of HFS joists with varying sizes and steel types, and subjected to varying load ratios. In summary, this research has significantly improved the knowledge and understanding of the fire performance of LSF floor systems made of hollow flange section joists and developed accurate fire design rules. Structural and fire design engineers can use the developed spread sheet based design tool to predict the fire performance of LSF floor systems made of HFS joists with varying sizes and steel types for a range of applications in commercial and residential buildings.

APA, Harvard, Vancouver, ISO, and other styles

32

Ferencz, Balázs. "Nosná železobetonová konstrukce objektu administrativní budovy." Master's thesis, Vysoké učení technické v Brně. Fakulta stavební, 2014. http://www.nusl.cz/ntk/nusl-226920.

Full text

Abstract:

The Master’s thesis is focused on the analysis and design of selected members of load-bearing structure of an administration building according to the ultimate limit states (ULS) and seviceability limit states (SLS). The calculation and the analysis was supported by design software SCIA ENGINEER 2012. Structural analysis deals with the design of the reinforced concrete (RC) flat slab above the 4rd strorey which is particularly supported by RC columns and particularly lies on RC walls. Furthermore, the Master’s thesis contains analysis of some selected columns of last three storeys, column of lowest storey, construction of stairway between 4rd and 5th storeys. The work beside this deals with the calculation and design of foundation of the object. The rest parts of the load-bearing structure are not solved in the Master’s thesis.

APA, Harvard, Vancouver, ISO, and other styles

33

Mao, Channg-Ren, and 毛昶人. "A Study on The Influence of Beam Web Buckling to Aseismic Capacity of Multiple-Story Steel Frame." Thesis, 1993. http://ndltd.ncl.edu.tw/handle/75346674200199373327.

Full text

APA, Harvard, Vancouver, ISO, and other styles

34

Lee, Jih Feng, and 李紀鋒. "The study of lateral buckling behavior and load capacity of steel beams with copes in flange and cavities in web." Thesis, 1995. http://ndltd.ncl.edu.tw/handle/05401358862727783954.

Full text

APA, Harvard, Vancouver, ISO, and other styles

35

Arjomandi, Kaveh. "MECHANICAL RESPONSE OF SANDWICH PIPES SUBJECT TO HYDROSTATIC PRESSURE AND BENDING." Thesis, 2010. http://hdl.handle.net/10222/13156.

Full text

Abstract:

The recent substantial increase in world demand for energy and raw material resources has accelerated oil and gas exploration and production. At the same time, the depletion of onshore and shallow water oil resources presents a challenge to engineers to develop new means of harvesting and transporting oil and gas from harsh and remote areas. Sandwich Pipe (SP) is a relatively new design concept developed to address the transportation of oil in deep and ultra-deep waters as well as in cold environments. The main focus of this thesis is on the characterization of the structural performance of these novel systems. Deep and ultra-deep water offshore pipelines are subjected to excessive hydrostatic external pressure during installation and operation. In this research, an innovative analytical solution was developed to evaluate the external pressure capacity of SPs by calculating the linear eigenvalues of the characteristic equations of the system. In the proposed solution, the interface condition between the layers of the system is accounted for in the governing equations. As well, a set of comprehensive parametric studies using the Finite Element (FE) method was developed to investigate both the elastic and plastic buckling response of SPs. The influence of various structural parameters such as the material, geometrical and intra-layer interaction properties on the characteristic behavior and the buckling pressure of SPs was examined. In addition to the proposed analytical solution, two sets of semi-empirical equations based on the FE analysis results were recommended in calculating the elastic and plastic buckling pressure of SPs. As bending represents an important loading state in the installation and service life of SPs, it should be considered a governing loading scenario. In this thesis, the behavior of SPs under bending was investigated using a comprehensive set of parametric studies. SP systems with a wide practical range of physical parameters were analyzed using the FE method, and the influence of various structural parameters on the characteristic response and bending capacity of the system was explored, including pipe geometry, core layer properties, material yield anisotropy of high-grade steel pipes, and various intra-layer adhesion configurations.

APA, Harvard, Vancouver, ISO, and other styles

36

Amobi, Ikechukwu Ugochukwu. "Structural, economic and material comparison of various steel grades under fatigue loading." Thesis, 2008. http://hdl.handle.net/10539/4714.

Full text

Abstract:

ABSTRACT As industries are upgrading rapidly from a lower steel grade to higher ones it has become necessary to study the effect of changing from lower steel grades to higher grades. This thesis reports on fatigue life and behaviour, economic implications and material composition of these higher strength steels (HSS) as compared to the conventional grades. Three grades are commercially available in South Africa: 300W, 350W and 460W. These different steel grades (conventional and HSS) with the same moment capacities where subjected to constant dynamic stresses and the fatigue crack growth of the overloading and unloading were monitored and compared with each other. The influences of the overloading and unloading made standard grades perform better under repeated loading than the HSS, since HSS have been proved to have poor ductility, resulting in lower number of cycles to failure. An 85% increase in material cost was generated as HSS replaces the conventional lower steel grades. Reduction in number of cycles to failure in HSS was over 500%. A space analysis for a multi-storey building with 10 beam floors was conducted for the various steel grades using a software package. The buckling and linear behaviours of these structures were compared. Although the deflections were not too far apart, it was shown clearly that grade lower steel grades performed better than the higher grades. An optimization was conducted using the parameters discussed in the text or obtained from experiment and computer modelling, in order to aid in the selection criterion of general purpose steel. Grade 300W was the optimal grade although the result was based mainly on the cost and fatigue behaviour of the three grades.

APA, Harvard, Vancouver, ISO, and other styles

37

Silva, Maria do Rosário Paiva. "Análise Numérica de Colunas Estaiadas." Master's thesis, 2017. http://hdl.handle.net/10316/97943.

Full text

Abstract:

Dissertação de Mestrado Integrado em Engenharia Civil apresentada à Faculdade de Ciências e Tecnologia
As colunas estaiadas podem ser utilizadas como elementos resistentes à compressão de uma estrutura que apresente elevada esbelteza e requisitos de montagem rápida. Colunas estaiadas pré-esforçadas (CEPE) é uma solução que visa aumentar a capacidade de carga em colunas esbeltas. Para tal, à coluna esbelta acrescentou-se um sistema de pré-esforço composto por tirantes pré-esforçados e braços que restringem ao longo do comprimento.Desde 1960 que vários investigadores realizam estudos experimentais, numéricos e analíticos sobre esta solução estrutural, mas o seu comportamento estrutural não é completamente compreendido.No âmbito do projeto HILONG foram realizadas análises experimentais e com essas foi desenvolvido um modelo de elementos finitos calibrado em função dessas experiências. A presente dissertação visa a realização de um estudo paramétrico extensivo baseado na simulação calibrada de elementos finitos fazendo variar o comprimento da coluna, a seção transversal, o nível de pré-esforço nos tirantes, a seção dos tirantes e o tipo do aço.Realizaram-se no total 1008 análises numéricas, 648 LBA (18 colunas*3 espessuras da coluna principal*6 níveis de pré-esforço*2 cabos) e 360 GMNIA (12 colunas*3 espessuras da coluna principal*5 níveis de pré-esforço*2 cabos*1nível de pré-esforço (L/1000)), usando o programa de elementos finitos ABAQUS.Conclui-se com o estudo paramétrico que a adição do sistema de pré-esforço é mais eficiente em colunas mais esbeltas, porque fornece restrições adicionais que aumentam a capacidade máxima da coluna. Verificou-se que o uso de tirantes com maior seção transversal e a menor espessura para a seção transversal da coluna principal obteve um benefício mais significativo na capacidade de carga da coluna.
The stayed columns can be used as compression resistant elements of a structure that presents high slenderness and fast assembly requirements.Prestressed stayed columns (PSSC) is a solution that aims to increase the load capacity in slender columns. To this end, a prestressed system composed of prestressed stays and cross-arms that restrict along the length were added to slender column.Since 1960, researchers have been investigated experimentally, numerically and analytically on this structural solution, but its structural behavior is not completely understood. In the scope of the HILONG project, experimental analysis was performed and a finite element model calibrated according to these experiments was developed.The present dissertation focusses on the performance of an extensive parametric study based on the calibrated simulation of finite elements by varying the length of the column, the cross section, the level of prestressed initial in stays, the section of the stays and steel grade.In total, 1008 numerical analysis, 648 LBA (18 columns*3 main column thickness*6 prestress level*2cables) and 360 GMNIA (12 columns*3 main columns thickness*5 prestress level*2 cables*1 amplitude of geometric imperfections (L/1000)) were carried out using the finite element software ABAQUS.It is concluded with the parametric study that the addition of the stay system is more efficient in slender columns because provides additional restrains that increases the ultimate capacity of column. It was found that the use of stays with larger cross section and the smaller thickness for the cross section of the main columns obtained a more significant benefit on the load carrying capacity of long columns.

APA, Harvard, Vancouver, ISO, and other styles

Dissertations / Theses on the topic 'Buckling capacity'

Create a spot-on reference in APA, MLA, Chicago, Harvard, and other styles