Academic literature on the topic 'Bleaching experiment'

Hydrogen peroxide (H2O2) is the most commonly used bleaching agent for cotton fabric. However, the conventional H2O2 bleaching formula is not applicable for cationized cotton due to the low whiteness index after bleaching, fabric weakening, and a significant loss of cationic sites. In this work, magnesium sulfate (MgSO4) was added in the H2O2 bleaching formula to stabilize the bleaching system for cationized cotton. Additionally, a screening experiment with temperature and time, and sodium hydroxide (NaOH), H2O2, and MgSO4 concentrations as the factors, and whiteness index, bursting strength, and color strength from dyeing as the responses, was formulated. A statistical model was created using JMP software, which demonstrated how the bleaching conditions influenced the fabric properties. This procedure can be useful for bleaching cationized cotton in production settings.

This study explored and improved the optimal scouring-bleaching process of Xinjiang scutched flax, based on its characteristics and the scouring-bleaching process of existing mature flax. The physical properties, such as length, strength, split degree and fineness, and the chemical composition of Xinjiang scutched flax, such as the content of cellulose, lipowax, pectin, hemicellulose, water-soluble matter, lignin, etc., were measured and analyzed. The approximate range of bleaching process parameters was determined referring to the existing general flax scouring-bleaching process. Thirdly, the orthogonal experiment of three factors and three levels interaction is designed, and the optimal scouring-bleaching process scheme is obtained after analysis and verification.

The effect of illumination on the outcome of subliminal psychodynamic activation experiments is discussed and the bleaching hypothesis Silverman, Ross, Adler, and Lustig in 1978 used to explain negative results under certain illumination conditions is critically evaluated. Illumination levels suggested by Silverman for this research do not completely agree with values used in most successful experiments prior to 1980. The sequence of tachistoscopic events usually presented in a typical experiment and information-processing considerations suggest that, contrary to Silverman's earlier suggestions, stimulus-field illumination should be higher than blank-field illumination. Aspects of the bleaching hypothesis are questionable, and it seems to be of minimal value because the specifics of how bleaching is thought to interfere with the effects were not documented by reference to the literature in photochemistry. Further empirical investigation of the effect of illumination could be combined with attempts to understand how this variable affects stimulus processing during subliminal psychodynamic activation.

Mass bleaching events are predicted to occur annually later this century. Nevertheless, it remains unknown whether corals will be able to recover between annual bleaching events. Using a combined tank and field experiment, we simulated annual bleaching by exposing three Caribbean coral species ( Porites divaricata , Porites astreoides and Orbicella faveolata ) to elevated temperatures for 2.5 weeks in 2 consecutive years. The impact of annual bleaching stress on chlorophyll a , energy reserves, calcification, and tissue C and N isotopes was assessed immediately after the second bleaching and after both short- and long-term recovery on the reef (1.5 and 11 months, respectively). While P. divaricata and O. faveolata were able to recover from repeat bleaching within 1 year, P. astreoides experienced cumulative damage that prevented full recovery within this time frame, suggesting that repeat bleaching had diminished its recovery capacity. Specifically, P. astreoides was not able to recover protein and carbohydrate concentrations. As energy reserves promote bleaching resistance, failure to recover from annual bleaching within 1 year will likely result in the future demise of heat-sensitive coral species.

Abstract Increasing carbon dioxide (CO2) emissions are raising sea surface temperature (SST) and causing ocean acidification (OA). While higher SST increases the frequency of mass coral bleaching events, it is unclear how OA will interact to affect this process. In this study, we combine in situ bleaching surveys around three tropical CO2 seeps with a 2-month two-factor (CO2 and temperature) tank experiment to investigate how OA and SST in combination will affect the bleaching susceptibility of tropical reef corals. Surveys at CO2 seep and control sites during a minor regional bleaching event gave little indication that elevated pCO2 influenced the bleaching susceptibility of the wider coral community, the four most common coral families (Acroporidae, Faviidae, Pocilloporidae, or Poritidae), or the thermally sensitive coral species Seriatopora hystrix. In the tank experiment, sublethal bleaching was observed at 31°C after 5 d in S. hystrix and 12 d in Acropora millepora, whereas controls (28°C) did not bleach. None of the measured proxies for coral bleaching was negatively affected by elevated pCO2 at pHT 7.79 (vs. 7.95 pHT in controls), equivalent to ∼780 µatm pCO2 and an aragonite saturation state of 2.5. On the contrary, high pCO2 benefitted some photophysiological measures (although temperature effects were much stronger than CO2 effects): maximum photosystem II quantum yields and light-limited electron transport rates increased in both species at high pCO2, whereas gross photosynthesis and pigment concentrations increased in S. hystrix at high pCO2. The field and laboratory data in combination suggest that OA levels up to a pHT of 7.8 will have little effect on the sensitivity of tropical corals to thermal bleaching. Indeed, some species appear to be able to utilize the more abundant dissolved inorganic carbon to increase productivity; however, these gains offset only a small proportion of the massive bleaching-related energy losses during thermal stress.

This paper researched the process rapidly degumming and bleaching apocynum venetum, which is one-bath alkali-H2O2 method and a specific technique. The three-factor quadratic general rotary unitized optimization[1] design was used to analyze the three parameters mostly affecting the degumming and bleaching process: the NaOH concentration, the H2O2 dosages and the processing time. Through the experiment, calculation, analysis and verification, the optimum combination of the three parameters for degumming and bleaching process was gotten: NaOH concentration 10～11(g/L), H2O2 dosages 9.5～10.5(g/L), processing time 120～135(min).

ABSTRACT Adverse effects of tooth bleaching on dental structures remain a topic of discussion in the literature, and the search for protocols that reduce such reported adverse effects is ongoing. The goal of this systematic literature review was to determine whether the use of tooth bleaching gels with added minerals, such as fluoride, calcium, hydroxyapatite, potassium nitrate, amorphous calcium phosphate, and casein phosphopeptide-amorphous calcium phosphate, reduced the occurrence of the main adverse effects of tooth bleaching. The electronic database search identified 16 studies that evaluated the effects of bleaching gels with added minerals on enamel hardness and/or roughness, mineral loss, post-treatment sensitivity, morphological changes, and/or cohesive enamel strength. The findings of this review suggest that the addition of minerals to bleaching gels can contribute to the reduction of most adverse effects, mainly sensitivity, without affecting treatment efficiency. How to cite this article Borges B, Vale M, Afonso F, Assunção I. Can Enhanced Peroxides Decrease the Side Effects of Tooth Bleaching? A Systematic Review of the Literature. Int J Experiment Dent Sci 2014;3(2):84-91.

Abstract Microenvironments play a significant part in understanding the post-mortem interval in forensic taphonomy. Recently, the value of weathering factors in relation to obtaining a PMI has been investigated further. In this study, observations were made to calculate the length of time it takes for three different bone elements (femur, rib, and scapula) to bleach in a UK summer and winter. This research also investigated whether there were any physicochemical modifications to the bone caused by bleaching. Porcine femora, scapulae, and ribs were placed into open and shaded areas of an outdoor research facility located in Oxfordshire, UK, during summer (July–Sep) and winter months (Dec–Mar). The specimens were monitored at 3-week intervals using photography, and an observational scoring method was developed to quantify the extent of bleaching. As temperatures are typically much lower in the UK compared with warmer climates, a controlled indoor-simulated desert experiment was also undertaken to be used as a control. This allowed sun bleaching and changes to the bone chemistry to be monitored in a controlled, high-UV environment for comparison with the UK outdoor experiments. Fourier transform infrared spectroscopy (FTIR) was employed to analyze physicochemical modifications to both the mineral and organic components of the bone. The FTIR was used to calculate crystallinity index (CI), mineral to organic ratio, and the relative amount of carbonate concentrations. Weather data was collected and a positive correlation was found between both ultraviolet (UV) levels and accumulated degree days (ADD) when compared with observational bleaching scores. Bleaching (whitening) of the bone samples occurred in both seasons but at different rates, with the bleaching process occurring at a slower rate in winter. During summer, the initial bleaching process was evident at 6 weeks, and by 9 weeks, the bones were an off-white colour. During the winter period, whitening of the bone started at 9 weeks; however, only the scapula and rib samples displayed a similar off-white colour. This colouration was observed at 13 weeks rather than at 9 weeks. The desert simulation samples started bleaching in a similar pattern to the outdoor samples after 1 week but the bones did not fully bleach. The bone chemistry, based on physicochemical properties obtained from the FTIR, showed a significant statistical difference between the simulated desert and winter season when compared against a control sample. For the winter samples, the mineral to organic ratio was significantly higher than that in the control, suggesting a reduction in the proportion of organic. For the samples in the simulated desert environment, the crystallinity index was significantly higher than that in the control samples, suggesting an increase in crystallinity. The results of this experiment support the fact that it is possible to achieve bleaching in a UK environment and that the minimal time frame for this to occur differs in seasons.

AbstractFor over three decades, scientists have conducted heat-stress experiments to predict how coral will respond to ocean warming due to global climate change. However, there are often conflicting results in the literature that are difficult to resolve, which we hypothesize are a result of unintended biases, variation in experimental design, and underreporting of critical methodological information. Here, we reviewed 255 coral heat-stress experiments to (1) document where and when they were conducted and on which species, (2) assess variability in experimental design, and (3) quantify the diversity of response variables measured. First, we found that two-thirds of studies were conducted in only three countries, three coral species were more heavily studied than others, and only 4% of studies focused on earlier life stages. Second, slightly more than half of all heat-stress exposures were less than 8 d in duration, only 17% of experiments fed corals, and experimental conditions varied widely, including the level and rate of temperature increase, light intensity, number of genets used, and the length of acclimation period. In addition, 95%, 55%, and > 35% of studies did not report tank flow conditions, light–dark cycle used, or the date of the experiment, respectively. Finally, we found that 21% of experiments did not measure any bleaching phenotype traits, 77% did not identify the Symbiodiniaceae endosymbiont, and the contribution of the coral host in the physiological response to heat-stress was often not investigated. This review highlights geographic, taxonomic, and heat-stress duration biases in our understanding of coral bleaching, and large variability in the reporting and design of heat-stress experiments that could account for some of the discrepancies in the literature. Development of some best practice recommendations for coral bleaching experiments could improve cross-studies comparisons and increase the efficiency of coral bleaching research at a time when it is needed most.

Effects of mercerizing treatment on water-retention value of bleaching coniferous wood pulp fibers were discussed and the mercerizing treatment conditions were optimized. The best conditions of mercerizing treatment is NaOH concentration of 7mol/L, temperature of 40°C and processing time of 100min. SEM showed that the fiber cell wall swelling increase after mercerization.

Diplomová práce se zabývá bělícím procesem při výrobě papíru. Hlavním cílem práce je zhodnotit současný stav bělící technologie ve firmě OP Papírna, s.r.o. a navrhnout úpravu, která povede k větší efektivitě této technologie. K vyřešení zadání byla provedena rešerše technologických principů bělení a dále provedeny laboratorní experimenty s cílem najít vhodné řešení. Přínos experimentů byl podpořen technologickými výpočty. Výsledky experimentů ukázaly, že současný stav bělící technologie lze několika způsoby zefektivnit. Bylo ukázáno, že podané návrhy mají potenciál velkých ekonomických i chemických úspor. Čtenáři práce se dostane základního přehledu technologie výroby buničiny a papíru se zaměřením na bělící proces a získá znalost jeho bilančních výpočtů.

Submitted by Edineia Teixeira (edineia.teixeira@unioeste.br) on 2019-03-12T21:37:08Z No. of bitstreams: 2 Wesley_Ferrari_2018.pdf: 5292494 bytes, checksum: 80e420551cea7ffdde2bfbfeff0d10eb (MD5) license_rdf: 0 bytes, checksum: d41d8cd98f00b204e9800998ecf8427e (MD5)
Made available in DSpace on 2019-03-12T21:37:08Z (GMT). No. of bitstreams: 2 Wesley_Ferrari_2018.pdf: 5292494 bytes, checksum: 80e420551cea7ffdde2bfbfeff0d10eb (MD5) license_rdf: 0 bytes, checksum: d41d8cd98f00b204e9800998ecf8427e (MD5) Previous issue date: 2018-03-23
Aims: Evaluate the efficacy of dental bleaching and the tooth sensitivity during and after the procedure using a Potassium Nitrate and Sodium Fluoride based desensitizer gel, with or without Chitosan microparticles. Methods and Materials: Forty-two patients with a minimum A2 degree of saturation were selected, divided into two groups (n = 21): DKF - Potassium Nitrate with Sodium Fluoride and DKF CHI - Potassium Nitrate with Sodium Fluoride plus Chitosan microparticles. Dental bleaching was performed in the upper arch, using 35% Hydrogen Peroxide in a single session, with three applications of 15 minutes each. The desensitizing gel was applied before the treatment and remained on the enamel for 10 minutes in both groups. Tooth sensitivity (TS) was recorded by participants by means of scores while the bleaching gel was in contact with the teeth (5, 10, 15, 20, 25, 30, 35, 40 and 45 minutes), as well as 1, 24 and 48 hours after application. The shade evaluation was performed at baseline and seven days after bleaching. TS was evaluated by the Mann-Whitney test (p <0.05). The Kruskal-Wallis test (p <0.05) was used to assess the degree of bleaching. Results: At the 40, 45 minute and 1 hour evaluation periods, the sensitivity levels of the DFK CHI group were significantly lower in relation to the DKF group. Regarding the shade level, there was no significant interference in the outcome for both groups evaluated. Conclusions: the addition of chitosan microparticles to the desensitizing agent decreases sensitivity during and after tooth bleaching without interfering on the bleaching efficacy.Clinical relevance: the use of a desensitizing agent with chitosan microparticles prior to dental bleaching may decrease dentin sensitivity, which is the most common side effect associated with tooth bleaching.
Objetivos: avaliar a efetividade do clareamento dental profissional e a intensidade da sensibilidade durante e após o clareamento, utilizando um dessensibilizante à base de Nitrato de Potássio e Fluoreto de Sódio, acrescido ou não de micropartículas de Quitosana. Metodologia: foram selecionados 42 pacientes com grau de saturação dental mínima A2, divididos em dois grupos (n=21): DKF – Nitrato de Potássio com Fluoreto de Sódio e DKF QUI – Nitrato de Potássio com Fluoreto de Sódio acrescido de micropartículas de Quitosana. O clareamento foi realizado na arcada superior, com o uso de Peróxido de Hidrogênio a 35% em sessão única, com três aplicações de 15 minutos cada. O gel dessensibilizante foi aplicado previamente ao tratamento e permaneceu sobre o esmalte por 10 minutos, em ambos os grupos. O grau de sensibilidade (GS) foi anotado pelos pacientes por meio de escores, durante o tempo em que o gel clareador esteve em contato com os dentes (5, 10, 15, 20, 25, 30, 35, 40 e 45 minutos), assim como 1, 24 e 48 horas após a aplicação. O grau de saturação da cor foi avaliado no início e sete dias depois do clareamento. O GS foi avaliado pelo teste de Mann- Whitney (p<0.05). Para a avaliação do grau de clareamento, foi aplicado o teste de Kruskal- Wallis (p<0.05). Resultados: nos períodos de avaliação de 40, 45 minutos e 1 hora, os níveis de sensibilidade do grupo DFK QUI foram significativamente menores em relação ao grupo DKF. No que se refere ao grau de clareamento, não houve interferência significativa no resultado para ambos os grupos avaliados. Conclusões: a adição de micropartículas de Quitosana ao agente dessensibilizante diminui a sensibilidade durante e após o clareamento dental sem interferir no grau de clareamento.Relevância clínica: o uso prévio de um agente dessensibilizante com micropartículas de Quitosana pode diminuir a sensibilidade dentinária, que é o efeito colateral mais comum associado ao clareamento dental.

Orientador: André Luiz Fraga Briso
Banca: Ticiane Cestari Fagundes Tozzi
Banca: Carlos Eduardo Francci
Resumo: Objetivo: O presente estudo teve como objetivo analisar a influência do modelo experimental e substrato nas alterações do esmalte dental decorrentes do tratamento clareador de consultório em diferentes tempos de análise. Materiais e Métodos: Um total de 140 discos contendo esmalte e dentina foram confeccionados, a dentina planificada e o esmalte polido e submetido ao teste de microdureza de superfície em KHN (MS) para padronização e seleção inicial dos espécimes (n= 80). A seguir, foram divididos em 8 grupos (n=10): G1- Controle in vitro em dentes humanos (VHC); G2- Clareamento in vitro utilizando agente clareador Pola Office a base de peróxido de hidrogênio a 35% (Pola PH 35%) em dentes humanos (VHP); G3- Controle in situ em dentes humanos (SHC); G4- Clareamento in situ com Pola PH 35% em dentes humanos (SHP); G5- Controle in vitro em dentes bovinos (VBC); G6- Clareamento in vitro com Pola PH 35% em dentes bovinos (VBP); G7- Controle in situ dentes bovinos (SBC); G8- Clareamento in situ com Pola PH 35% em dentes bovinos (SBP). O esmalte dental foi avaliado quantitativamente pelas análises de rugosidade, MS e microdureza longitudinal do esmalte em KHN (ML) e qualitativamente por microscopia eletrônica de varredura (MEV). As análises de rugosidade e MS foram realizadas antes do início do tratamento (T0), após a 3° semana de tratamento (T1) e 15 dias após o término do tratamento (T2). Já a análise de ML e as imagens de MEV foram realizadas apenas em T2. Os dados foram submetido... (Resumo completo, clicar acesso eletrônico abaixo)
Abstract: Objective: The objective of the present study was to analyze, influence, model, experimental, substrate, birth, treatment, repair, surgery, different times, analysis. Materials and Methods: a total of 140 discotheques containing enamel and dentin were made, a planned dentin and polished omalmalte and submitted to the surface microhardness test in KHN (MS) for standardization and initial selection of spagos (n = 80). They were divided into 8 groups (n = 10): G1- In vitro control in human teeth (VHC); G2- In vitro bleaching, for example, Pola Office whitening agent, 35% hydrogen peroxide base (Pola PH 35%) in human teeth (VHP); G3-In situ control in human teeth (SHC); G4- In situ bleaching with Pola PH 35% in human teeth (SHP); G5- In vitro control in bovine teeth (VBC); G6- In vitro whitening with PH Pola 35% in bovine teeth (VBP); G7- In situ control of bovine teeth (SBC); G8- In situ bleaching with Pola PH 35% in bovine teeth (SBP). The enamel was evaluated quantitatively in the analysis of roughness, MS and longitudinal microhardness of the enamel in KHN (ML) and qualitatively by scanning electron microscopy (SEM). The roughness and MS analyzes were performed before the start of treatment (T0), after one week of treatment (T1) and 15 days after treatment (T2). Already an ML analysis and as SEM images were performed only in T2. The data were submitted to the Shapiro-wilk homoscedasticity test, then performed in analysis of variance (ANOVA) of measures and Tukey or Sidak test repetitions (p <0.05) or Friedman's test, by the post test Hoc analysis of Wilcoxon with Bonferroni correction. Results: In the relativity of in vitro and in situ models, a statistically significant difference can be observed 15 days after the end of the bleaching treatment (p <0.05) in all analyzes, In situ. Regarding the substrates, these...
Mestre

Orientadores: José Roberto Lovadino, Débora Alves Nunes Leite Lima
Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Odontologia de Piracicaba
Made available in DSpace on 2018-08-22T14:49:11Z (GMT). No. of bitstreams: 1 Vieira_HenriqueHeringer_M.pdf: 2738449 bytes, checksum: 3bff0e9a86d6f5de5afbaa869d38e4a8 (MD5) Previous issue date: 2013
Resumo: Este trabalho divido em dois estudos teve como objetivos: 1 - Avaliar através de microcisalhamento a influência de três tipos de matrizes para confecção dos cilindros de resina composta sobre a resistência de união a dentina, 2- Avaliar a aplicação de um agente antioxidante experimental, antes e durante o procedimento adesivo, sobre a resistência de união aos substratos dentais clareados. Todas as amostras foram feitas com adesivo simplificado convencional (Single Bond / 3M ESPE) e resina fluida de nanopartículas (Filtek Z 350 Flow / 3M ESPE). Para o estudo 1 vinte dentes bovinos foram cortados, lixados e planificados, a fim de expor a dentina coronária. Em cada fragmento dental foram confeccionados três cilindros, cada feito com um tipo diferente de matriz: 1 - matriz de silicone, 2 - matriz experimental de macarrão e 3 - matriz de Tygon. A remoção dos tipos 1 e 3 de matrizes se fez pelo corte da matriz, e do tipo 2 por imersão em água até que o macarrão se soltasse do espécime. As amostras foram submetidas ao microcisalhamento. Os dados foram analisados através de análise unidirecional de variância (ANOVA) (? = 0,05). Não houve diferença estatística entre os diferentes tipos de matrizes estudadas. Para o estudo 2 foram utilizados 100 fragmentos de dentes bovinos, medindo 6x6x1mm de espessura. Os fragmentos foram distribuídos em 10 grupos, variando o substrato dental (esmalte e dentina) e tratamento a ser realizado: controle (sem tratamento), clareamento (peróxido de hidrogênio 35%) sem aplicação do agente antioxidante, clareamento com aplicação do agente antioxidante por 10 minutos antes do procedimento restaurador, clareamento com aplicação do agente antioxidante por 10 minutos após o condicionamento ácido, clareamento com aplicação do agente antioxidante por 30 minutos antes do condicionamento ácido. Após um período de 24 horas armazenado em saliva, os corpos de prova foram submetidos ao teste de microcisalhamento. Então foi aplicada análise de variância (ANOVA) "1 way" e teste de Tukey, considerando o nível de significância 5%, e análise do padrão de fratura. Não foi encontrada diferença estatística na resistência de união para o esmalte. Em dentina os grupos que receberam tratamento com antioxidante apresentaram valores de resistência de união intermediários aos grupos controle e sem tratamento antioxidante. Pode-se concluir que o tipo de matriz não interferiu nos resultados de resistência de união a dentina, e que o agente antioxidante apresentou bom comportamento por elevar os valores de resistência de união à dentina clareada
Abstract: This work divided in two studies aimed to: 1 - Evaluate through microshear the influence of three types of matrices for the fabrication of composite resin cylinders on the bond strength to dentin; 2 - Evaluate the application of an experimental antioxidant, before and during the adhesive procedure on the bond strength to dental substrates bleached. All samples were made with conventional simplified adhesive (Single Bond / 3M ESPE) and nanoparticles flow composite (Filtek Z 350 Flow / 3M ESPE). For the first study twenty bovine incisors were cuted, grinded and planned in order to expose coronal dentin. Each dental fragment received three cylinders, each one made with a different type of matrix: 1 - silicone matrix, 2 - experimental matrix and 3 - Tygon matrix. Removal of the 1 and 3 matrix types were made by cutting the matrix, and type 2 by immersion in water until the noodle let out of the specimen. Samples were so subjected to microshear. Data were analyzed using one-way analysis of variance (ANOVA) and Tukey's test (? = 0.05). There was no statistical difference between the matrices studied. For study 2 one hundred fragments of bovine incisors were used, measuring 6x6 mm and height of enamel and dentin 1mm each. The fragments were distributed into 10 groups, varying the dental substrate (enamel and dentin) and treatment to be performed: Control (no treatment), bleaching (hydrogen peroxide 35%) without application of antioxidant, bleaching agent application antioxidant for 10 minutes before the restorative procedure, bleaching with agent application antioxidant for 10 minutes after the acid etching, bleaching with agent application antioxidant for 30 minutes before etching. After a period of 24 hours stored in saliva, the samples passed by microshear test. So was applied one way ANOVA, considered the 5% significance level, and analysis of the fracture pattern. There was no statistical difference in enamel. In dentin the groups that received treatment with antioxidant, showed intermediate values compared with untreated and control groups. Can be concluded that the type of matrix does not affect the results of bond strength to dentin, and that the antioxidant showed good behavior by raising the values of bond strength to bleached dentin
Mestrado
Dentística
Mestre em Clínica Odontológica

Submitted by Úrsula Aparecida Escalero Silva null (ursula_escalero@yahoo.com.br) on 2017-08-02T18:57:18Z No. of bitstreams: 1 Dissertação_Úrsula Ap.Escalero Silva.doc: 13796352 bytes, checksum: e2a920646451b977374b362f4919a2fb (MD5)
Rejected by LUIZA DE MENEZES ROMANETTO (luizamenezes@reitoria.unesp.br), reason: Solicitamos que realize uma nova submissão seguindo as orientações abaixo: A versão final da dissertação/tese deve ser submetida no formato PDF (Portable Document Format). O arquivo PDF não deve estar protegido e a dissertação/tese deve estar em um único arquivo, inclusive os apêndices e anexos, se houver. Por favor, corrija o formato do arquivo e realize uma nova submissão. Agradecemos a compreensão. on 2017-08-02T19:45:03Z (GMT)
Submitted by Úrsula Aparecida Escalero Silva null (ursula_escalero@yahoo.com.br) on 2017-08-02T19:46:57Z No. of bitstreams: 3 Dissertação_Úrsula Ap.Escalero Silva.doc: 13796352 bytes, checksum: e2a920646451b977374b362f4919a2fb (MD5) Dissertação_Úrsula Aparecida Escalero Silva.pdf: 2945525 bytes, checksum: e290e7a6e39c728875be5fc9f2337205 (MD5) Dissertação_Úrsula Aparecida Escalero Silva.pdf: 2945525 bytes, checksum: e290e7a6e39c728875be5fc9f2337205 (MD5)
Rejected by LUIZA DE MENEZES ROMANETTO (luizamenezes@reitoria.unesp.br), reason: Solicitamos que realize uma nova submissão seguindo as orientações abaixo: - Foram submetidos 3 arquivos PDF’s, apenas 1 arquivo deve ser submetido Corrija estas informações e realize uma nova submissão contendo o arquivo correto. Agradecemos a compreensão. on 2017-08-02T19:50:31Z (GMT)
Submitted by Úrsula Aparecida Escalero Silva null (ursula_escalero@yahoo.com.br) on 2017-08-02T19:52:22Z No. of bitstreams: 1 Dissertação_Úrsula Aparecida Escalero Silva.pdf: 2945525 bytes, checksum: e290e7a6e39c728875be5fc9f2337205 (MD5)
Approved for entry into archive by LUIZA DE MENEZES ROMANETTO (luizamenezes@reitoria.unesp.br) on 2017-08-03T12:35:30Z (GMT) No. of bitstreams: 1 silva_uae_me_araca.pdf: 2945525 bytes, checksum: e290e7a6e39c728875be5fc9f2337205 (MD5)
Made available in DSpace on 2017-08-03T12:35:30Z (GMT). No. of bitstreams: 1 silva_uae_me_araca.pdf: 2945525 bytes, checksum: e290e7a6e39c728875be5fc9f2337205 (MD5) Previous issue date: 2017-06-08
Objetivo: O presente estudo teve como objetivo analisar a influência do modelo experimental e substrato nas alterações do esmalte dental decorrentes do tratamento clareador de consultório em diferentes tempos de análise. Materiais e Métodos: Um total de 140 discos contendo esmalte e dentina foram confeccionados, a dentina planificada e o esmalte polido e submetido ao teste de microdureza de superfície em KHN (MS) para padronização e seleção inicial dos espécimes (n= 80). A seguir, foram divididos em 8 grupos (n=10): G1- Controle in vitro em dentes humanos (VHC); G2- Clareamento in vitro utilizando agente clareador Pola Office a base de peróxido de hidrogênio a 35% (Pola PH 35%) em dentes humanos (VHP); G3- Controle in situ em dentes humanos (SHC); G4- Clareamento in situ com Pola PH 35% em dentes humanos (SHP); G5- Controle in vitro em dentes bovinos (VBC); G6- Clareamento in vitro com Pola PH 35% em dentes bovinos (VBP); G7- Controle in situ dentes bovinos (SBC); G8- Clareamento in situ com Pola PH 35% em dentes bovinos (SBP). O esmalte dental foi avaliado quantitativamente pelas análises de rugosidade, MS e microdureza longitudinal do esmalte em KHN (ML) e qualitativamente por microscopia eletrônica de varredura (MEV). As análises de rugosidade e MS foram realizadas antes do início do tratamento (T0), após a 3° semana de tratamento (T1) e 15 dias após o término do tratamento (T2). Já a análise de ML e as imagens de MEV foram realizadas apenas em T2. Os dados foram submetidos ao teste de homocedasticidade Shapiro-wilk, em seguida, foi realizada à análise de variância (ANOVA) dois fatores medidas-repetidas e pós-teste de Tukey ou Sidak (p<0,05) ou teste de Friedman, seguido pelo teste post hoc de Wilcoxon com correção de Bonferroni. Resultados: Na comparação entre os modelos in vitro e in situ, em todas as análises realisadas, pode-se notar diferença estatisticamente significante 15 dias após o término do tratamento clareador (p< 0,05), sendo evidente a recuperação do esmalte dentário no modelo in situ. Com relação aos substratos, estes apresentaram diferença estatística nas análises de MS e ML (p> 0,05). No tocante a análise dos grupos ao longo do tempo, nas variáveis rugosidade e MS, observou-se diferenças estatísticas (p<0,05), comprovando a ação negativa do tratamento clareador em T1, seguida em T2 pela manutenção dessas alterações no grupo in vitro e recuperação dessas superfícies nos grupos in situ. Conclui-se que: O modelo experimental foi decisivo para o estudo das alterações do esmalte dentário clareado, pois, o modelo in situ permite redução ou recomposição das alterações dentárias promovidas pelo tratamento clareador. - Em pesquisas sobre o clareamento dental, ambos os substratos empregados neste estudo podem ser utilizados, desde que, as diferenças existentes entre eles sejam consideradas no momento da interpretação dos dados. - Os diferentes tempos de análise foram determinantes para a observação da ação do agente clareador sobre a estrutura dental.
Objective: The objective of the present study was to analyze, influence, model, experimental, substrate, birth, treatment, repair, surgery, different times, analysis. Materials and Methods: a total of 140 discotheques containing enamel and dentin were made, a planned dentin and polished omalmalte and submitted to the surface microhardness test in KHN (MS) for standardization and initial selection of spagos (n = 80). They were divided into 8 groups (n = 10): G1- In vitro control in human teeth (VHC); G2- In vitro bleaching, for example, Pola Office whitening agent, 35% hydrogen peroxide base (Pola PH 35%) in human teeth (VHP); G3-In situ control in human teeth (SHC); G4- In situ bleaching with Pola PH 35% in human teeth (SHP); G5- In vitro control in bovine teeth (VBC); G6- In vitro whitening with PH Pola 35% in bovine teeth (VBP); G7- In situ control of bovine teeth (SBC); G8- In situ bleaching with Pola PH 35% in bovine teeth (SBP). The enamel was evaluated quantitatively in the analysis of roughness, MS and longitudinal microhardness of the enamel in KHN (ML) and qualitatively by scanning electron microscopy (SEM). The roughness and MS analyzes were performed before the start of treatment (T0), after one week of treatment (T1) and 15 days after treatment (T2). Already an ML analysis and as SEM images were performed only in T2. The data were submitted to the Shapiro-wilk homoscedasticity test, then performed in analysis of variance (ANOVA) of measures and Tukey or Sidak test repetitions (p <0.05) or Friedman's test, by the post test Hoc analysis of Wilcoxon with Bonferroni correction. Results: In the relativity of in vitro and in situ models, a statistically significant difference can be observed 15 days after the end of the bleaching treatment (p <0.05) in all analyzes, In situ. Regarding the substrates, these presented a statistical difference in the MS and ML analyzes (p> 0.05). Regarding the analysis of the groups over time, in the roughness and MS variables, statistical statistics (p <0.05) were observed, proving a negative action of the bleaching treatment in T1, instead of T2 through maintenance, there were no groups In vitro and surface recovery in in situ groups. It is concluded that: The experimental model was decisive for the study of the author's keywords, the in situ model allows to reduce or to reward the dental alternatives promoted by the bleaching treatment. - In research on dental bleaching of the substrates used in the study can be used, since, as residues between them, are not considered in the interpretation version of the data. - The different times of analysis were determinant for an observation of the action of the bleaching agent on a dental structure.

Bleaching is defined as the disruption of the symbiotic relationship between the host and Symbiodinium dinoflagellates, resulting in the exposure of the calcium carbonate skeleton. This phenomenon has been mostly linked to seawater temperature elevation. Bleaching events are becoming more intense and frequent, harming coral reefs around the world and affecting almost 100% of the community in some places. Therefore, it is important to understand if the effects of these recurrent stress events are cumulative on this photosymbiotic relationship. We experimentally tested how the Symbiodinium-associated jellyfish Cassiopea andromeda is affected by three consecutive thermal stress events, monitoring bell size and chlorophyll-a concentration. Jellyfishes in four physiological conditions regarding feeding frequency (daily and every three days) and Symbiodinium concentration (low and high) were subject to a one-week thermal stress at each experimental round. Three treatments were applied: 27ºC (control, maintained in this temperature during all experiment), 30ºC and 33ºC. After a three-week recovery period at 27ºC, thermal stress events were applied on two more instances intertwined by a recovery period. C. andromeda bleached and its chlorophyll-a content decreased for all temperatures during the first thermal stress and only at 33ºC for the second and third events. Size was only affected by feeding and by the second thermal stress. Higher food offer caused organisms to increase in size while those offered food with lower frequency shrunk. As observed in other hosts, high Symbiodinium concentration resulted in loss of chlorophyll-a, probably due to excessive production of reactive oxygen species and self-shading. C. andromeda jellyfish bleached just in the first stress event and its resilience to multiple thermal stresses is dependent upon biotic and abiotic factors. There was no difference in mortality in any condition or temperature applied. Feeding plays a crucial role on size and symbiotic dependency under thermal stress. Symbiodinium concentration is an important factor in experiments testing climate change scenarios and although symbiont concentration has no relation to the growth of the host, it affects the Symbiodinium itself, thus might be considered in future experiments. Chronic effects of multiple thermal stresses were observed for chlorophyll-a, while these were acute for growth. C. andromeda apparently does not rely only on Symbiodinium, especially under stressful conditions and can be used as a model to investigate the effects of climate change in Symbiodinium symbiosis. Without major host mortality, the behavior of Symbiodinium in its physiological limits after every single bleaching event can be monitored.
O branqueamento é definido pela ruptura da relação simbiótica entre o hospedeiro e o dinoflagelado Symbiodinium, resultando na exposição do esqueleto de carbonato de cálcio do hospedeiro, e tem sido associado principalmente à elevação da temperatura da água do mar. Esses eventos estão se tornando mais intensos e frequentes, prejudicando recifes de corais ao redor do mundo, resultando em branqueamento de quase 100% da comunidade em alguns locais. Portanto, é importante entender se os efeitos desses eventos de estresse são cumulativos neste relacionamento fotossimbiótico. No presente estudo foi experimentalmente testado como medusas de Cassiopea andromeda em simbiose com Symbiodinium são afetadas por três eventos consecutivos de estresse térmico, monitorando o tamanho da umbrella e a concentração de clorofila-a. Medusas em quatro condições fisiológicas em relação à frequência de aporte heterotrófico (diário e a cada três dias) e a concentração de Symbiodinium (baixa e alta) foram sujeitas a um estresse térmico de uma semana em cada rodada experimental. Foram aplicados três tratamentos: 27ºC (controle, mantido nesta temperatura durante todo o experimento), 30ºC e 33ºC. Após um período de recuperação de três semanas a 27ºC, os eventos de estresse térmico foram aplicados em mais duas instâncias interligadas por um período de recuperação. C. andromeda branqueou e sua clorofila-a diminuiu para todas as temperaturas durante o primeiro estresse térmico e apenas a 33ºC para o segundo e terceiro eventos. O tamanho só foi afetado pela alimentação e pelo segundo estresse térmico. A oferta de alimento mais frequente fez com que os organismos aumentassem de tamanho, enquanto aqueles aos quais se oferecia com uma menor frequência, diminuíram de tamanho. Conforme observado em outros hospedeiros, a alta concentração de Symbiodinium resultou em perda de clorofila-a, provavelmente devido à produção excessiva de espécies reativas de oxigênio e auto-sombreamento. Medusas de C. andromeda branquearam apenas no primeiro evento de estresse e sua resiliência a múltiplos estresses térmicos depende de condições bióticas e abióticas. Não houve diferença na mortalidade em qualquer condição ou temperatura aplicada. Sob condições de estresse térmico, o aporte heterotrófico desempenha um papel crucial no tamanho e dependência da simbiose. A concentração de Symbiodinium é um fator importante nos experimentos que utilizam cenários de mudanças climáticas. Embora a concentração de simbiontes não tenha relação com o crescimento do hospedeiro, isso afeta o próprio Symbiodinium e, portanto, deve ser considerado em futuros experimentos. Efeitos crônicos de múltiplos estresses térmicos foram observados para a clorofila-a, enquanto estes são agudos para o crescimento. C. andromeda aparentemente não depende do Symbiodinium, especialmente sob condições estressantes e pode ser usado como modelo para investigar os efeitos das alterações climáticas no Symbiodinium em simbiose. Sem maior mortalidade do hospedeiro, o comportamento do Symbiodinium pode ser monitorado até seus limites fisiológicos após cada evento de branqueamento.

Cette these est consacree a l'etude de la delignification des pates cellulosiques par le bioxyde de chlore ou l'eau oxygenee dans le but d'ameliorer la selectivite de ces reactifs et de minimiser les rejets toxiques. L'etude comparative de la delignification et du blanchiment par le bioxyde de chlore montre que la phase d constituee des sous-phases: introduction progressive de clo#2 en milieu alcalin (ph10) et reaction en milieu acide (ph4,7) du chlorite precedemment forme est le meilleur procede. La cinetique de la reaction limitante de ce procede (sous-phase acide, reaction du chlorite) est etudiee par la suite. L'influence du ph, des catalyseurs ainsi que celles des stabilisants et complexants sur la cinetique de decomposition de h#2o#2 est etudiee. La complexite du phenomene conduit a la modelisation des cinetiques. Le modele propose (somme d'une cinetique d'ordre 1 et d'ordre 2) est teste dans un large domaine experimental dans les conditions du blanchiment et montre le role particulierement complexe des ions metalliques (fe) apportes par les reactifs. Cependant en regroupant les experiences suivant des criteres d'impuretes apportees par la soude, la modelisation conduit a des resultats tres satisfaisants qui permettent de valider le modele. L'etude de la cinetique de delignification et du blanchiment par h#2o#2 d'une pate ecrue de resineux, d'une pate preblanchie ce et des pates ecrues ayant subi un pretraitement acide est abordee. Elle permet d'attribuer a la reaction un ordre 1 par rapport a l'eau oxygenee et conduit a proposer un processus de blanchiment certes plus long mais dont la selectivite est amelioree

L'objectif de ce travail est d'analyser les effets de l'ozone sur les hydrates de carbone et la lignine contenus dans les pates a papier chimiques, et en particulier dans les pates kraft de résineux, ainsi que les conséquences de ces effets sur la qualité des pates blanchies a l'ozone, et sur les résultats obtenus dans des stades de blanchiment ultérieurs. Apres un premier chapitre consacre a une revue de la littérature sur l'ozone en milieu aqueux, sur son action sur les hydrates de carbone et la lignine, ainsi que sur son utilisation dans le blanchiment des pates a papier chimiques, un deuxième chapitre porte sur l'analyse des effets de l'ozone sur les hydrates de carbone et la lignine résiduelle d'une pate kraft de résineux, et plus globalement sur diverses pates a papier de différentes natures. Dans le troisième chapitre sont étudiés les effets des cations métalliques sur le blanchiment a l'ozone, en distinguant les cations présents dans la pate de ceux éventuellement présents dans l'eau du procédé. Le quatrième chapitre traite du cas de l'ozone dans des séquences de blanchiment sans composes chlores, et plus particulièrement des conséquences des modifications apportées par l'ozonation a la cellulose et a la lignine sur un stade de blanchiment ultérieur. L'optimisation de la séquence choisie est également réalisée. Dans le cinquième chapitre l'ensemble des résultats obtenus est explique en faisant appel, entre autres, a des techniques de détection des radicaux hydroxyles, et a des expérimentations de gamma radiolyse de l'eau. Les actions respectives de l'ozone moléculaire et des radicaux hydroxyles générés sont ainsi précisées. En conclusion les perspectives de l'utilisation de l'ozone en blanchiment sont discutées

A new heat sink has been designed that increases the run time of a cavity-filling resin-curing or teeth-bleaching dental device with light emitting diode. The heat sink is a hollowed copper object that is filled with a phase change material. Computational simulations and experimental measurements are presented that show the heat sink with phase change material increases the run time of the device beyond the minimum requirement of six minutes.