Dissertations / Theses on the topic 'Bimetallic alloys'

Magnetic recording technology is ubiquitous in the modern world and constitutes a corner stone of current research and development. Recent inventions such as heat-assisted magnetic recording and exchange-coupled media has focused magnetic recording research towards alloys exhibiting strong magnetocrystalline anisotropies. In this thesis, we investigate, from first principles using the screened Korringa-Kohn-Rostoker method, the effect of a range of compositional and microstructural defects and features upon the magnetocrystalline anisotropy energy (MAE) of FePt and CoPt alloys. We show that localised Pt alloying affects the MAE of bulk Co primarily through the Pt-induced effects on the Co sites. We demonstrate that stacking faults often reduce the Co MAE and that the effect of composite stacking faults upon the MAE is not necessarily additive, but synergistic. By varying the unit cell geometry and the compositional parameters of FePt, we show that the formation of complete Fe layers is, generally, the dominant factor in maintaining a large MAE. We investigate the magnetic properties (spin moments, magnetocrystalline anisotropy and magnetic exchange) across an Fe/FePt/Fe multi-layer and show that the effective exchange exhibits a strong reduction at the Fe/FePt interfaces and that the MAE of the whole multilayer system is very slightly reduced by the presence of the Fe/FePt interfaces. Across all systems, we observe that localised features such as stacking faults, interfaces and localised alloying incur relatively long-ranged spatial oscillations in the MAE, which may, in turn, cause significant finite-size effects on the nano-scale.

Scanning Tunnelling Microscopy (STM) was utilised together with the high resolution depth-profiling capabilities of Medium Energy Ion Scattering (MEIS), a technique traditionally associated with single crystal substrates, to probe the mean size and depth dependent composition profile of bimetallic PdAu nanoparticles on planar oxide surfaces as functions of the starting composition and annealing temperature. In order to fit composition profiles to experimental MEIS data, a new analysis tool has been designed that models the particles as flat-topped structures with a hexagonal base which can be divided into a number of shells, each shell corresponding to a particular ion pathlength inside the material. The reliability of this method will be discussed in detail. Fitting results show that the surface layers are always significantly enriched in Au compared to the bulk alloy composition. By comparing MEIS data for clean surfaces data for modified surfaces it was found that Pd generally segregates towards the particle surface on adsorption of acetic acid. The interaction of potassium acetate with Au/Pd{111} alloy surfaces of varying composition has been investigated using Temperature Programmed Desorption (TPD) and Reflection Absorption Infra Red Spectroscopy (RAIRS). At lower coverage, potassium acetate reacts reversibly with the surface to form CO and carbonate. Formation of surface acetate is observed on Pd-rich surfaces only. At higher coverage, acetate is the major surface species formed on all samples examined.

The techniques of optoperforation, spectral characterization of alloy disorder, and metal-enhanced fluorescence were applied to previously unconsidered or disregarded systems in order to demonstrate that such applications are both feasible and consequential. These applications were the subject of three disparate works and, as such, are independently discussed. Despite being ostensibly restricted to mammalian cells, optoperforation was demonstrated in intact plant cells by means of successful femtosecond-laser-mediated infiltration of a membrane impermeable dextran-conjugated dye into cells of vital Arabidopsis seedling stems. By monitoring the rate of dye uptake, and the reaction of both CFP-expressing vacuoles and nanocellulose substrates, the intensity and exposure time of the perforating laser were adjusted to values that both preserved cell vitality and permitted the laser-assisted uptake of the fluorophore. By using these calibrated laser parameters, dye was injected and later observed in targeted cells after 72 hours, all without deleteriously affecting the vital functions of those cells. In the context of alloy disorder, photoluminescence of excitonic transitions in two InAsxP1-x alloys were studied through temperature and magnetic field strength dependencies, as well as compositionally-dependent time-resolved behavior. The spectral shape, behavior of the linewidths at high magnetic fields, and the divergence of the peak positions from band gap behavior at low temperatures indicated that alloy disorder exists in the x=0.40 composition while showing no considerable presence in the x=0.13 composition. The time-resolved photoluminescence spectrum for both compositions feature a fast and slow decay, with the slow decay lifetime in x=0.40 being longer than that of x=0.13, which may be due to carrier migration between localized exciton states in x=0.40. In order to achieve broadband metal-enhanced fluorescence in upconverting NaYF4:Yb,Er nanocrystals, two nanocomposite architectures were proposed that retrofit metallic nanoshells to these lanthanide-doped nanocrystals. The typical monometallic construction was rejected in favor of architectures featuring Au-Ag bimetallic concentric surfaces, a decision supported by the considerable overlap of the calculated plasmon modes of the metallic structures with the emission and absorption spectrum of the nanocrystals. Furthermore, precursors of these nanocomposites were synthesized and photoluminescence measurements were carried out, ultimately verifying that these precursors produce the requisite upconversion emissions.
Ph. D.

Philosophiae Doctor - PhD
Lithium ion cathode systems based on composites of lithium iron phosphate (LiFePO₄), iron-cobalt-derivatised carbon nanotubes (FeCo-CNT) and polyaniline (PA) nanomaterials were developed. The FeCo-functionalised CNTs were obtained through in-situ reductive precipitation of iron (II) sulfate heptahydrate (FeSO₄.7H₂O) and cobalt (II) chloride hexahydrate (CoCl₂.6H₂O) within a CNT suspension via sodium borohydrate (NaBH₄) reduction protocol. Results from high Resolution Transmission Electron Microscopy (HRTEM) and Scanning Electron Microscopy (SEM) showed the successful attachment FeCo nanoclusters at the ends and walls of the CNTs. The nanoclusters provided viable routes for the facile transfer of electrons during lithium ion deinsertion/insertion in the 3-D nanonetwork formed between the CNTs and adjacent LiFePO₄ particles.

We focused on a non-cooling room temperature microbolometer infrared imaging array device which includes a sensing layer of p-type a-Si:H component layers doped with boron. Boron incorporation and bonding configuration were investigated for a-Si:H films grown by plasma enhanced chemical deposition (PECVD) at varying substrate temperatures, hydrogen dilution of the silane precursor, and dopant to silane ratio using multiple internal reflection infrared spectroscopy (MIR-IR). This study was then confirmed from collaborators via Raman spectroscopy. MIR-IR analyses reveal an interesting counter-balance relationship between boron-doping and hydrogen-dilution growth parameters in PECVD-grown a-Si:H. Specifically, an increase in the hydrogen dilution ratio (H2/SiH4) or substrate temperature was found to increase organization of the silicon lattice in the amorphous films. It resulted in the decrease of the most stable SiH bonding configuration and thus decrease the organization of the film. The new chemical bonding information of a-Si:H thin film was correlated with the various boron doping mechanisms proposed by theoretical calculations. The study revealed the corrosion morphology progression on aluminum alloy (Al, 0.5% Cu) under acidic chloride solution. This is due to defects and a higher copper content at the grain boundary. Direct galvanic current measurement, linear sweep voltammetry (LSV), and Tafel plots are used to measure corrosion current and potential. Hydrogen gas evolution was also observed (for the first time) in Cu/Al bimetallic interface in areas of active corrosion. Mechanistic insight that leads to effective prevention of aluminum bond pad corrosion is explored and discussed. (Chapter 4) Aluminum bond pad corrosion activity and mechanistic insight at a Cu/Al bimetallic interface typically used in microelectronic packages for automotive applications were investigated by means of optical and scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and electrochemistry. Screening of corrosion variables (temperature, moisture, chloride ion concentration, pH) have been investigated to find their effect on corrosion rate and to better understand the Al/Cu bimetallic corrosion mechanism. The study revealed the corrosion morphology progression on aluminum alloy (Al, 0.5% Cu) under acidic chloride solution. The corrosion starts as surface roughening which evolves into a dendrite structure and later continues to grow into a mud-crack type corrosion. SEM showed the early stage of corrosion with dendritic formation usually occurs at the grain boundary. This is due to defects and a higher copper content at the grain boundary. The impact of copper bimetallic contact on aluminum corrosion was explored by sputtering copper microdots on aluminum substrate. Copper micropattern screening revealed that the corrosion is activated on the Al/Cu interface area and driven by the large potential difference; it was also seen to proceed at much higher rates than those observed with bare aluminum. Direct galvanic current measurement, linear sweep voltammetry (LSV), and Tafel plots are used to measure corrosion current and potential. Hydrogen gas evolution was also observed (for the first time) in Cu/Al bimetallic interface in areas of active corrosion. Mechanistic insight that leads to effective prevention of aluminum bond pad corrosion is explored and discussed. Micropattern corrosion screening identified hydrogen evolution and bimetallic interface as the root cause of Al pad corrosion that leads to Cu ball lift-off, a fatal defect, in Cu wire bonded device. Complete corrosion inhibition can be achieved by strategically disabling the mutually coupled cathodic and anodic reaction cycles.

Core-shell electrocatalysts are of interest for the oxygen reduction reaction in proton exchange membrane fuel cells as enhancements in activity have been reported compared to the traditionally-used Pt/C electrocatalysts. To fully understand the origin of the activity of these samples, and how the structure changes in the electrochemical environment, full in situ structural characterisation is required. The aim of this work was to develop and apply in situ synchrotron based X-ray characterisation techniques (EXAFS, WAXS, SAXS and ASAXS) to study a set of well-defined Pd-core, Pt-shell electrocatalysts with 0.5, 1, 2 and 4 monolayers (ML) of Pt, with the primary motivation of determining the advantages and limitations of each technique when applied to materials of this nature. Measurements were conducted in and ex situ to study the effect of Pt-shell thickness on the structure of the nanoparticles and the response to applied electrode potential. Catalyst electrodes subjected to accelerated ageing tests were also characterised to investigate the mechanisms of degradation responsible for an observed loss in electrochemical surface area, with the dominant mechanism found being dissolution for the core-shell catalysts with ≤ 2 ML shell and coalescence (Ostwald ripening) for the 4 ML. EXAFS was found to be the most useful of the four techniques owing to the detailed structural information obtainable and the relative ease of data collection. The SAXS data provided information not obtained from the EXAFS, and combined with electrochemical measurements, enabled determination of the mechanisms of degradation. WAXS provided complementary information to the EXAFS. Attempts to fit the ASAXS data with a simplistic model were unsuccessful, thus, without the application of more complex theoretical models, little additional information could be obtained from this technique.

We focused on a non-cooling room temperature microbolometer infrared imaging array device which includes a sensing layer of p-type a-Si:H component layers doped with boron. Boron incorporation and bonding configuration were investigated for a-Si:H films grown by plasma enhanced chemical deposition (PECVD) at varying substrate temperatures, hydrogen dilution of the silane precursor, and dopant to silane ratio using multiple internal reflection infrared spectroscopy (MIR-IR). This study was then confirmed from collaborators via Raman spectroscopy. MIR-IR analyses reveal an interesting counter-balance relationship between boron-doping and hydrogen-dilution growth parameters in PECVD-grown a-Si:H. Specifically, an increase in the hydrogen dilution ratio (H2/SiH4) or substrate temperature was found to increase organization of the silicon lattice in the amorphous films. It resulted in the decrease of the most stable SiH bonding configuration and thus decrease the organization of the film. The new chemical bonding information of a-Si:H thin film was correlated with the various boron doping mechanisms proposed by theoretical calculations. The study revealed the corrosion morphology progression on aluminum alloy (Al, 0.5% Cu) under acidic chloride solution. This is due to defects and a higher copper content at the grain boundary. Direct galvanic current measurement, linear sweep voltammetry (LSV), and Tafel plots are used to measure corrosion current and potential. Hydrogen gas evolution was also observed (for the first time) in Cu/Al bimetallic interface in areas of active corrosion. Mechanistic insight that leads to effective prevention of aluminum bond pad corrosion is explored and discussed. (Chapter 4) Aluminum bond pad corrosion activity and mechanistic insight at a Cu/Al bimetallic interface typically used in microelectronic packages for automotive applications were investigated by means of optical and scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and electrochemistry. Screening of corrosion variables (temperature, moisture, chloride ion concentration, pH) have been investigated to find their effect on corrosion rate and to better understand the Al/Cu bimetallic corrosion mechanism. The study revealed the corrosion morphology progression on aluminum alloy (Al, 0.5% Cu) under acidic chloride solution. The corrosion starts as surface roughening which evolves into a dendrite structure and later continues to grow into a mud-crack type corrosion. SEM showed the early stage of corrosion with dendritic formation usually occurs at the grain boundary. This is due to defects and a higher copper content at the grain boundary. The impact of copper bimetallic contact on aluminum corrosion was explored by sputtering copper microdots on aluminum substrate. Copper micropattern screening revealed that the corrosion is activated on the Al/Cu interface area and driven by the large potential difference; it was also seen to proceed at much higher rates than those observed with bare aluminum. Direct galvanic current measurement, linear sweep voltammetry (LSV), and Tafel plots are used to measure corrosion current and potential. Hydrogen gas evolution was also observed (for the first time) in Cu/Al bimetallic interface in areas of active corrosion. Mechanistic insight that leads to effective prevention of aluminum bond pad corrosion is explored and discussed. Micropattern corrosion screening identified hydrogen evolution and bimetallic interface as the root cause of Al pad corrosion that leads to Cu ball lift-off, a fatal defect, in Cu wire bonded device. Complete corrosion inhibition can be achieved by strategically disabling the mutually coupled cathodic and anodic reaction cycles.

Polymer electrolyte fuel cells (PEFCs) have emerged as a promising renewable emission-free technology to solve the worldwide increasing demand for clean and efficient energy conversion. Despite large efforts in academia and automotive industry, the commercialization of PEFC vehicles still remains a great challenge. Critical issues are high material costs, insufficient catalytic activity as well as longterm durability. Especially due to the sluggish kinetics of the oxygen reduction reaction (ORR), high Pt loadings on the cathode are still necessary which leads to elevated costs. Alloys of Pt with other less precious metals (Co, Ni, Fe, Cu, etc.) show improved ORR activities compared to pure Pt catalysts. However, state-of-the-art carbon-supported catalysts suffer from severe Pt and carbon corrosion during the standard operation of PEFCs, affecting their reliability and long-term efficiency. Multimetallic aerogels constitute excellent candidates to overcome these issues. Due to their large open pores and high inner surface areas combined with electrical conductivity, they are ideal for applications in electrocatalysis. In addition, they can be employed without any catalyst support. Therefore, the fabrication of bimetallic Pt-M (M=Ni, Cu, Co, Fe) aerogels for applications in fuel cell catalysis was the focus of this thesis. Based on a previously published synthesis for Pt–Pd aerogels, a facile one-step procedure at ambient conditions in aqueous solution was developed. Bimetallic aerogels with nanochain diameters of as small as 4 nm and Brunauer-Emmett-Teller (BET) surface areas of up to 60 m2/g could be obtained. Extensive structure analysis of Pt–Ni and Pt–Cu aerogels by powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), X-ray absorption spectroscopy (XAS), scanning transmission electron microscopy coupled with energy-dispersive X-ray spectroscopy (STEM-EDX) and electrochemical techniques showed that both metals were predominantly present in their metallic state and formed homogeneous alloys. However, metal (hydr)oxide byproducts were observed in aerogels with higher contents of non-precious metal (>25 %). Moreover, electronic and geometric structures were similar to those of carbon-supported Pt alloy catalysts. As a result, ORR activites were comparable, too. A threefold improvement in surface-specific activity over Pt/C catalysts was achieved. The mass-specific activites met or exceeded the U.S. Department of Energy (DOE) target for automotive PEFC applications. Furthermore, a direct correlation between non-precious metal content in the alloy and ORR activity was discovered. Aerogels with nonprecious metal contents >25% turned out to be susceptible to dealloying in acid leaching experiments, but there was no indication for the formation of extended surface structures like Pt-skeletons. A Pt3Ni aerogel was successfully employed as the cathode catalyst layer in a differential fuel cell (1 cm2), which is a crucial step towards technical application. This was the first time an unsupported metallic aerogel was implemented in a PEFC. Accelerated stress tests that are usually applied to investigate the support stability of fuel cell catalysts revealed the excellent stability of Pt3Ni alloyed aerogels. In summary, the Pt alloy aerogels prepared in the context of this work have proven to be highly active oxygen reduction catalysts with remarkable stability.

Over the last decades, many steps have been taken in the search for an effective method to reduce carbon dioxide to small organic molecules that can be used as fuel or building blocks for the chemical industry. The object of this work is to prepare two bimetallic electrocatalysts utilizing Cu combined with Au or In for the efficient and selective reduction of CO2 to CO, HCOOH and small fuels molecules. The copper-gold electrode is prepared through the electrodeposition of Cu on the surface of Au, using the underpotential deposition (UPD) technique to obtain a copper monolayer. The prepared electrode shows a high current density compared to Au electrode. Bimetallic metal oxides of CuInO2 is used as the precursor to prepare Cu-In alloys electrodes for electrochemical reduction of CO2. The electrocatalyst preparation is carried out using a thermal reducing treatment able to form different catalytic surfaces with different Cu-In alloys or single-phase metals. The best sample shows a high faradaic efficiency toward CO (71%) at the low overpotential of −0.8 V vs RHE. This study shows two examples of scalable and inexpensive preparation methods of bimetallic surfaces, which may use as selective electrocatalysts for the aqueous reduction of CO2.

Recently, the increasing level of atmospheric CO₂ has been widely noticed due to its association with global warming, provoking a growth in environmental concerns toward the continued use of fossil fuels. To mitigate the concentration of atmospheric CO₂, various strategies have been implemented. Among options to turn waste CO₂ into useful fuels and chemicals, carbon capture and utilisation along with renewable hydrogen production as the source materials for methanol production is more preferable. In the 1960s, the highly active and economic Cu/ZnO/Al₂O₃ catalyst was developed for CO₂ hydrogenation reaction to methanol, since then, metal nanoparticles and nanocomposites have been extensively investigated and applied. Especially, bimetallic catalysts have emerged as an important class of catalysts due to their unique properties and superior catalytic performances compared to their monometallic counterparts. This thesis presents the evolution of the catalyst development for CO₂ hydrogenation to methanol: Firstly, we introduced the CuZn-based catalysts with Zn content increased in the bimetallic CuZn system via a heterojunction synthesis approach. Secondly, we increased the active CuZn sites via introducing ultra-thin layered double hydroxide as the catalyst precursor for methanol production from CO₂ and H₂. Thirdly, a new class of Rh-In bimetallic catalysts were studied, which shows high methanol yield and selectivity under thermodynamically unfavourable methanol synthesis conditions owing to the strong synergies of Rh-In bimetallic system. Fourthly, for the renewable methanol production from H₂ and CO₂, the hydrogen source must come from the green production routes. Therefore, an in-depth study of a nanocomposite system, CdS-carbon nanotubes-MoS₂, for photocatalytic hydrogen production from water has been demonstrated. Finally, the conclusion of this thesis is given and an outlook is presented for the future development in this research area.

This dissertation is focused on understanding heterogeneous bimetallic catalysts using model catalyst systems, such as Pd-Au/Mo(110), Pd/Au(111) and Pd/Au(100). Monometallic and bimetallic model catalysts, composed of Pd and Au, were prepared by physical vapor deposition (PVD) onto well-characterized metal substrates. Subsequent characterization was performed using an arsenal of modern surface science tools: low energy ion scattering spectroscopy (LEISS), infrared absorption spectroscopy (IRAS), temperature programmed desorption (TPD), and x-ray photoelectron spectroscopy (XPS). Electronic, morphological, and chemical properties of the prepared model catalysts were compared to those observed from monometallic single-crystal model catalysts such as Cu(100), Pd(111), Au(100), and Au(111). Between 700 K and 1000 K, formation of stable alloy surfaces of Pd-Au mixtures on Mo(110) was accompanied by substantial enrichment in Au. Annealing a 1:1 Pd-Au mixture at 800 K yields a Pd0.2Au0.8 surface alloy; the concentration of isolated Pd sites in this surface alloy can be systematically controlled by a judicious selection of initial bulk Pd-Au concentration. Pd-Au catalysts supported on Au(111) and Au(100) substrates generated a surface ensemble of Pd monomers surrounded by Au after annealing the systems at or above 550 K. To test the activity and selectivity of the prepared bimetallic model catalysts, the formation rate of vinyl acetate monomer (VAM) was examined. More significant enhancement of VAM formation rate was observed for bimetallic catalysts supported on Au(100) compared to those on Au(111). A critical surface ensemble composed two non-contiguous Pd monomers was proposed for the VAM synthesis. Oxygen plays a critical role in the efficiency of the synthetic route. Structure-reactivity correlations were established based on the suggested elementary reactions leading to the oxidative coupling of ethylene and acetic acid to form VAM.

1.1\xMagnetic nanoparticles (NPs) with sizes ranging from 2 to 20 nm in diameter represent an important class of artificial nanostructured materials, since the NP size is comparable to the size of a magnetic domain. They have potential applications in data storage, catalysis, permanent magnetic nanocomposites, and biomedicine.;1.2\xTo begin with, a brief overview on the background of Fe-based bimetallic NPs and their applications for data-storage and catalysis was presented in Chapter 1.;1.3\xIn Chapter 2, L10-ordered FePt NPs with high coercivity were directly prepared from a novel bimetallic acetylenic alternating copolymer P3 by a one-step pyrolysis method without post-thermal annealing. The chemical ordering, morphology and magnetic properties were studied. Magnetic measurements showed that a record coercivity of 3.6 T (1 T = 10 kOe) was obtained in FePt NPs. By comparison of the resultant FePt NPs synthesized under Ar and Ar/H2, the characterization proved that the incorporation of H2 would affect the nucleation and promote the growth of FePt NPs. The L10 FePt NPs were also successfully patterned on Si substrate by nanoimprinting lihthography (NIL). The highly ordered ferromagnetic arrays on a desired substrate for bit-patterned media (BPM) were studied and promised bright prospects for the progress of data-storage.;1.4\xFuthermore, we also reported a new FePt-containing metallopolymer P4 as the single-source precursor for metal alloy NPs synthesis, where the metal fractions were on the side chain and the ratio could be easily controlled. This polymer was synthesized from random copolymer poly(styrene-4-ethynylstyrene) PES-PS and bimetallic precursor TPy-FePt ([Pt(4-ferrocenyl-(NN̂N̂))Cl]Cl) by Sonogashira coupling reaction. After pyrolysis of P4, the stoichiometry of Fe and Pt atoms in the synthesized NPs (NPs) is nearly close to 1:1, which is more precise than using TPy-FePt as precursor. Polymer P4 was also more favorable for patterning by high throughout NIL as compared to TPy-FePt. Ferromagnetic nanolines, potentially as bit-patterned magnetic recording media, were successfully fabricated from P4 and fully characterized.;1.6\xBesides, a bimetallic complex TPy-FePd-2 was prepared and used as a single-source precursor to synthesize ferromagnetic FePd NPs by one-pot pyrolysis. The resultant FePd NPs have a mean size of 19.8 nm and show the coercivity of 1.02 kOe. In addition, the functional group (-NCMe) in TPy-FePd-2 was easily substituted by a pyridyl group. A random copolymer PS-P4VP was used to coordinate with TPy-FePd-2, and the as-synthesized polymer made the metal fraction disperse evenly along the flexible chain. Fabrication of FePd NPs from the polymers was also investigated, and the size could be easily controlled by tuning the metal fraction in polymer. FePd NPs with the mean size of 10.9, 14.2 and 17.9 nm were prepared from the metallopolymer with 5 wt%, 10 wt% and 20wt% of metal fractions, respectively.;1.7\xIn Chapter 4, molybdenum disulfide (MoS2) monolayers decorated with ferromagnetic FeCo NPs on the edges were synthesized through a one-step pyrolysis of precursor molecules in an argon atmosphere. The FeCo precursor was spin coated on the MoS2 monolayer grown on Si/SiO2 substrate. Highly-ordered body-centered cubic (bcc) FeCo NPs were revealed under optimized pyrolysis conditions, possessing coercivity up to 1000 Oe at room temperature. The FeCo NPs were well-positioned along the edge sites of MoS2 monolayers. The vibration modes of Mo and S atoms were confined after FeCo NPs decoration, as characterized by Raman shift spectroscopy. These MoS2 monolayers decorated with ferromagnetic FeCo NPs can be used for novel catalytic materials with magnetic recycling capabilities. The sizes of NPs grown on MoS2 monolayers are more uniform than from other preparation routines. Finally, the optimized pyrolysis temperature and conditions provide receipts for decorating related noble catalytic materials.;1.8\xFinally, Chapters 5 and 6 present the concluding remarks and the experimental details of the work described in Chapters 2-4.

The need for green and renewable fuels has led to the investigation of ways to exploit renewable resources. Solar among all the renewables is the most powerful and its conversion into usable energy would help in solving the energy problem our society is facing. Photocatalytic water splitting for hydrogen production is an example of solar energy storage into chemical bonds. The hydrogen produced in this way can then be employed as carbon free fuel creating the “Hydrogen Cycle”. This work investigates the structure and the activity of graphitic carbon nitride (g-C₃N₄), an organic semiconductor that proved a suitable photocatalyst for hydrogen production from water. Synthesised by thermal polycondensation of melamine it is a graphitic like material with a band gap of 2.7 eV which makes it a visible light active catalyst. In a first instance the effect of the synthesis conditions on its structure and morphology are investigated to find the optimum parameters. The temperature of condensation is varied from 450°C up to 650°C and the length from 2.5 h to 15 h. The structural changes are monitored via X-ray diffraction (XRD) and elemental analysis while the effect on the morphology and the band gap of g-C₃N₄ are investigated by mean of scanning electron microscopy and UV-Vis absorption. Subsequently, a study of the crystal structure of the catalyst is carried out. Using structures proposed in the literature, X-ray diffraction and neutron scattering simulations are used to narrow down the number of possible 3D structures. After structural characterisation, the activity of g-C₃N₄ for photocatalytic hydrogen evolution is evaluated. It is confirmed that loading 1 wt.% Pt on its surface significantly increases the hydrogen evolution rate. The attention then focuses on the loading procedures, the reduction pre treatments of the co-catalyst and the reasons of the different performances when different procedures are employed. The catalytic system is characterised by mean of X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM) and XRD. By investigating the composition and the morphology of the platinum nanoparticles under different conditions, the main factors responsible for the changes in activity of g-C₃N₄ for hydrogen evolution are identified. Additionally, the role of the co catalyst and its interaction with g-C₃N₄ is also elucidated. Finally, taking forward the knowledge acquired on the Pt-g-C₃N₄ system, the effect on the hydrogen evolution rate of alloying platinum with a second metal (Cu, Ag, Ni and Co) is studied. The nanoparticles are characterised by XRD and TEM. A screening of the loading procedures and bimetallic systems is performed to identify the most promising for photocatalytic hydrogen evolution with the aim of bringing them towards further investigation.

Submitted by Livia Mello (liviacmello@yahoo.com.br) on 2016-09-22T12:28:02Z No. of bitstreams: 1 TeseGZ.pdf: 5741494 bytes, checksum: b3b8ef01bdd4c76791ffc531be6a07da (MD5)
Approved for entry into archive by Marina Freitas (marinapf@ufscar.br) on 2016-10-10T14:38:01Z (GMT) No. of bitstreams: 1 TeseGZ.pdf: 5741494 bytes, checksum: b3b8ef01bdd4c76791ffc531be6a07da (MD5)
Approved for entry into archive by Marina Freitas (marinapf@ufscar.br) on 2016-10-10T14:38:09Z (GMT) No. of bitstreams: 1 TeseGZ.pdf: 5741494 bytes, checksum: b3b8ef01bdd4c76791ffc531be6a07da (MD5)
Made available in DSpace on 2016-10-10T14:38:17Z (GMT). No. of bitstreams: 1 TeseGZ.pdf: 5741494 bytes, checksum: b3b8ef01bdd4c76791ffc531be6a07da (MD5) Previous issue date: 2016-02-29
Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)
The oil exploitation and production at the pre-salt fields in a safety and efficient way depends on the development of materials that withstand the severe work conditions found in these fields. For instance, pipes, such as drilling risers and casings, are often subjected to severe wear and corrosion conditions. This thesis is dedicated to evaluate the technical feasibility to produce wear and corrosion resistant bimetallic pipes by spray forming. The processing-microstructure-properties relationship of the spray-formed boron-modified supermartensitic stainless steel (SMSS) grades was comprehensively studied. Deposits of SMSS with boron contents ranging from 0.3 %wt. to 1.0 %wt. were processed by spray forming. The spray-formed boron-modified SMSS deposits had the wear resistance evaluated through different wear tests and their corrosion resistances by means of electrochemical techniques. It was demonstrated that the wear resistance of the spray-formed boron-modified SMSS is determined by the presence of the eutectic network of M 2B-type borides resulted from the spray forming process. On the other hand, the corrosion resistance of the spray-formed boron-modified SMSS is controlled by the chemical composition of the martensitic matrix. Furthermore, spray-formed bimetallic pipes composed of boron-modified SMSS and conventional SMSS were produced in the unique semi-industrial scale spray-forming plant of the Foundation Institute of Materials Science (IWT-University of Bremen, Germany). The relationship between the process parameters and the metallurgical quality of the pipes was addressed. It was shown that the key to produce a spray-formed bimetallic pipe with good metallurgical quality is adjusting the process parameters in such a way that the deposition zone’s temperature is kept within the alloy’s solidification temperature range during the whole deposition process. Moreover, solidification and grain size evolution models in spray forming were proposed. Finally, the mechanical properties of one of the spray-formed bimetallic pipes in the as-spray formed condition and after heat treatments were evaluated.
A exploração e produção de petróleo nos poços do pré-sal de modo seguro e eficiente dependem do desenvolvimento de ligas que suportem severas condições de trabalho. Por exemplo, tubos como risers de perfuração e casings são frequentemente submetidos à severas condições de desgaste e corrosão. Esta tese se dedica a avaliar a viabilidade técnica de produzir tubos bimetálicos resistentes à corrosão e ao desgaste conformados por spray. A relação processamento-microestrutura-propriedade do aço inoxidável supermartensítico (AISM) modificado com boro e conformado por spray foi estudada de forma abrangente. Depósitos de AISM com teores de boro variando de 0,3%p. a 1,0%p. foram processados por conformação por spray. Os depósitos tiveram a resistência ao desgaste avaliada através de diferentes ensaios e a resistência à corrosão por meio de técnicas eletroquímicas. Demonstrou-se que a resistência ao desgaste das ligas modificadas com boro é determinada pela presença de boretos eutéticos, do tipo M2B, oriunda do processo de conformação por spray. Por outro lado, a resistência à corrosão das ligas modificadas com boro é controlada pela composição química da matriz. Além disso, tubos bimetálicos compostos de AISM modificado com boro e AISM convencional foram produzidos em escala semi-industrial na planta de conformação por spray do Instituto de Ciência dos Materiais (IWT-Universidade de Bremen). A relação entre os parâmetros de processo e a qualidade metalúrgica dos tubos foi tratada. Mostrou-se que a chave para produzir tubos bimetálicos conformados por spray com boa qualidade metalúrgica é o ajustar os parâmetros do processo de tal modo que a temperatura da zona de deposição permaneça dentro do intervalo de solidificação da liga durante todo processo. Além disso, modelos de solidificação e evolução de tamanho de grão em conformação por spray foram propostos. Finalmente, avaliou-se as propriedades mecânicas de um dos tubos bimetálicos conformado por spray, com e sem tratamentos térmicos.
FAPESP: 12/25352-4

Current ethanol oxidation catalysts in direct ethanol fuel cells (typically platinum-based) suffer from low conversion and are susceptible to CO poisoning. Therefore we determined to find viable alternative catalysts for ethanol oxidation based on iridium using density functional theory to model bimetallic alloy (111) surfaces. Iridium was alloyed with another transition metals M in an overlayer (one layer of metal M on top of bulk iridium) or subsurface configuration (M is inserted under the first layer of iridium). Complete oxidation of ethanol is limited by the breaking of strong C-C bonds, so any catalyst must lower the barriers for C-C bond breaking. We modeled the reaction CH+CO →CHCO.Segregation energies were calculated and the subsurface configuration was the most stable configuration in the vast majority of alloy cases. CO adsorption was also studied and a lower CO adsorption energy was found in many alloy cases compared to pure Pt (, providing encouraging results about the possibility of reducing CO poisoning. Activation energies were lowered for the vast majority of the alloys used in an underlayer structure, reinforcing our interest in the underlayer structures or “subsurfaceâ€� alloys. Finally, we found, based on the CO adsorption energies, activation energies of the C-C breakage reaction, and metal cost, three important catalyst descriptors, a number of promising catalysts for the ethanol oxidation reaction. The most interesting alloys all adopted the underlayer structure Ir/M/Ir. With M = Ta, Hf, Nb, V, Zr, they demonstrated enhanced reactivity and high CO tolerance, having the advantage of reducing the cost of the catalyst, potentially substituting expensive platinum group metals by more affordable components.

Les nanoparticules bimétalliques supportées sont des catalyseurs particulièrement attractifs en raison d’une activité et d’une stabilité accrues par rapport à leurs homologues monométalliques. Dans cette thèse des solides à base d'or ont été étudiés en tant que catalyseurs de l'oxydation sélective du glucose en absence de base. Il a été mis en évidence que la variation du ratio molaire entre l’or et le second métal (Pd, Pt, or Cu) a un impact différent sur les performances catalytiques en fonction de la nature du second métal, du support et de la méthode de préparation. Les séries Au-Pd supportés sur TiO2 et préparés par la méthode de sol-immobilisation et Au-Cu supportés sur TiO2 et préparés par la méthode de précipitation-réduction ont montré un effet synergique important, en particulier lorsque le rapport entre les deux métaux était de 1. Ces catalyseurs convertissent sélectivement le glucose en acide gluconique et leur activité a été trouvée supérieure à celle des contreparties monométalliques. L'analyse XPS a démontré que les espèces Au+δ, Pd+2 et CuOH jouent alors un rôle important dans la réaction étudiée en absence de base. Le bismuth en tant que second métal n'a montré aucun effet bénéfique, au contraire du palladium et du cuivre. Les catalyseurs à base d’Au et de Pt supportés sur ZrO2 se sont avérés quant à eux très stables lorsque la teneur en or était inférieure à 0,3% en masse. La nature du support a un impact très important sur le mécanisme de la réaction conduite en absence base sur des catalyseurs à base d’or. La raison réside dans les interactions que ce support développe avec la phase bimétallique favorisant ainsi la formation des espèces actives
The supported bimetallic nanoparticles are particularly attractive catalysts due to the increased activity and stability over their monometallic counterparts. In this thesis, gold-based solids have been studied as catalysts for the selective base-free oxidation of glucose. It has been demonstrated that the variation of the molar ratio between gold and the second metal (Pd, Pt, or Cu) has a different impact on the catalytic performances depending on the nature of the second metal, the support and the method of preparation. TiO2 supported Au-Pd series prepared by the sol-immobilization method and Au-Cu series prepared by the precipitation-reduction method showed a significant synergistic effect, particularly when the ratio of the two metals was 1. Under the reaction conditions used (T = 60 °C or 80 °C, P = 5 bar air, t = 5 h), these catalysts selectivity to gluconic acid and their activity was found to be greater than that of monometallic counterparts, especially when the catalyst is supported on TiO2. XPS analysis showed that the Au+δ, Pd+2 and CuOH species played an important role in the base-free reaction. Bismuth as the second metal showed no beneficial effect, unlike palladium and copper. The Au-Pt catalysts supported on ZrO2 proved to be still active when the gold content was less than 0.3 wt.%. Ultimately, the nature of the support has a very important impact on the mechanism of the base-free reaction conducted on gold-based catalysts (formation of H2O2 in situ). The reason lies in the interactions of the support with the bimetallic phase thus favoring the formation of the active species

L’émergence de nouveaux matériaux structurés à l’échelle nanométrique, aux propriétés contrôlées, a ouvert de nouvelles perspectives vis-à-vis des matériaux qui nous entourent. C’est notamment le cas des métaux et de leurs alliages et il est crucial d’établir le lien entre leurs propriétés structurales et leurs propriétés chimique et physique pour en permettre une utilisation optimale. Cette thèse s’inscrit dans ce contexte et porte sur la synthèse et la caractérisation en microscopie électronique en transmission de nanoparticules d’alliage bimétallique Au-Cu. En s’appuyant sur le diagramme de phase décrit à l’échelle macroscopique, nous nous sommes particulièrement intéressés aux nanoparticules de compositions nominales Au3Cu, AuCu et AuCu3. Le premier axe de ce travail consiste en l’élaboration de nanoparticules d’alliage Au-Cu. Deux voies de synthèse sont explorées : la voie chimique reposant sur le procédé polyol et la voie physique par ablation par laser pulsé. Le premier mode d’élaboration permet l’obtention de nanoparticules parfaitement cubiques dont la composition est systématiquement riche en Au. Les nanoparticules produites par voie physique présentent en revanche une composition maitrisée et modifiable. D’un point de vue structural, un recuit de ces dernières particules mène à leur mise en ordre chimique et à l’observation de structures L10 et L12. Cependant, nous montrons que cette transition de phase est bloquée dans les nanostructures présentant des défauts structuraux. Enfin, l’évolution du paramètre de maille des nanoparticules synthétisées selon ces deux voies de synthèse, en fonction de leur composition, a été établie et suit exactement la loi de Vegard décrite pour le matériau massif.Dans un second temps, nous avons observé des nanoparticules obtenues par voie physique en microscopie électronique en transmission environnementale, c’est-à-dire dans des conditions proches des environnements d’utilisation habituellement appliqués en catalyse. Les expériences menées en température révèlent que le mécanisme de dissolution de nanoparticules d’Au et d’alliage Au-Cu portées à haute température se fait en deux étapes : il y a fusion des nanoparticules suivi de leur évaporation pour des tailles de nanoparticules centrées autour de 10 nm. Les expériences réalisées en couplant le chauffage des nanoparticules au passage d’un gaz (H2 ou O2), en flux et dans des conditions de pression bien supérieures à celles accessibles jusqu’à maintenant, ont permis d’étudier leur comportement thermodynamique en condition oxydantes et réductrices. Nous avons notamment montré que des cycles d’oxydo-réduction de nanoparticules de taille moyenne supérieure à 20 nm conduisent à un effet Kirkendall menant, de manière réversible, à la formation de nanoparticules creuses (doughnut). Cette thèse interdisciplinaire constitue travail pionnier dans la compréhension du système d’alliage bimétallique Au-Cu à l’échelle nanoscopique
The emergence of new materials, structured at the nanoscale, with controlled properties, has opened new prospects regarding materials around us. In particular for metals and alloys, it seems crucial to connect their structural properties to their chemical and physical properties in order to optimise their use.Within this context, this thesis is focused on the synthesis and the characterisation of Au-Cu bimetallic alloy nanoparticles by transmission electron microscopy. On the basis of the bulk phase diagram, we especially studied particles with nominal compositions Au3Cu, AuCu et AuCu3.The first part of this work is dedicated to the synthesis of nanoparticles in two different ways. The chemical way is based on the polyol process and leads to nanoparticles exhibiting a cubic shape, and a systematically rich Au content. On the other hand, nanoparticles obtained by Pulsed Laser Deposition (PLD), a physical method of synthesis, display a well-controlled and tuneable composition. From a structural point of view, the annealing of the particles leads to chemical order and the stabilisation of L10 and L12 structures. However, we reveal that this phase transition is blocked in nanostructures with crystal defects. Moreover, we establish the evolution of the lattice parameter of the particles as a function of the composition and we demonstrate that, as in the bulk case, it is in agreement with Vegard’s law.In the second part, the nanoparticles synthesised via the physical method are studied using environmental transmission electron microscopy, i.e. in conditions close to those usually applied in catalytic reactors. Experiments performed at high temperature highlight that the dissolution of Au and Au-Cu nanoparticles occurs in a two-step process: fusion occurs first and is followed by evaporation for nanoparticles with a mean diameter of 10 nm.Coupling heating with gas flow (H2 or O2) in higher pressure condition than those usually reached allows us to study the thermodynamic behaviour of the nanoparticles in oxidative or reductive conditions. Most Notably, we show that oxidation-reduction cycles performed on nanoparticles with a diameter larger than 20 nm leads to a Kirkendall effect and the reversible formation of hollow particles (doughnuts).This cross-disciplinary thesis is a pioneering work towards understanding the bimetallic Au-Cu alloy system at atomic scale

In this work, a simple, less time consuming electrochemical method in the form of an electrochemical sensor has been developed for the detection of PAHs. The sensor was fabricated by the deposition of silver-gold (1:3) alloy nanoparticles (Ag-AuNPs) on ultrathin overoxidized polypyrrole (PPyox) film which formed a PPyox/Ag-AuNPs composite on glassy carbon electrode (PPyox/Ag-AuNPs/GCE). The silver-gold alloy nanoparticles deposited to form the composite were chemically prepared by simultaneous reduction of silver nitrate (AgNO3) and chloroauric acid (HAuCl4) using sodium citrate and characterized by UV-visible spectroscopy technique which confirmed the homogeneous formation of the alloy nanoparticles.

Des nouveaux catalyseurs bimétalliques à base de palladium et de cuivre ont été développés. Deux voies de préparation ont été testées : l'imprégnation successive (TSI) et la co-imprégnation (CI) en utilisant la zéolithe 4Å (4A) et l'oxyde mixte MgAlxOy comme support. Les catalyseurs ont été caractérisés à l'état frais et testés dans la réaction de couplage Suzuki–Miyaura afin de comparer leurs activités, sélectivités et stabilités. L'étude de stabilité nous a montré que le catalyseur Cu-Pd-4A-TSI restait actif pendant six cycles alors que l'activité du catalyseur Cu-Pd-4A-CI diminuait. Sur le support MgAlxOy, le catalyseur CI était stable pendant six cycles contrairement au catalyseur TSI. Nous avons montré que le point clé pour l'obtention d'une bonne activité et stabilité est la présence de la phase active correspondant à l'alliage Cu/Pd 1/1 identifiée grâce à la caractérisation des catalyseurs et ce quelle que soit la méthode de préparation des catalyseurs. Une différence cruciale existe entre les catalyseurs supportés sur MgAlxOy et 4A : le catalyseur Cu–Pd supporté sur MgAlxOy permet de réduire le temps de réaction de moitié pour une même conversion par rapport à Cu-Pd-4A-TSI. De plus, l'utilisation d'un support plus basique permet, dans une certaine mesure, la diminution de la quantité de la base ajoutée durant la réaction. La réaction Petasis-borono Mannich a été aussi effectuée avec succès sur ces catalyseurs
New bimetallic palladium/copper catalysts were developed by successive impregnation (TSI) and co-impregnation (CI) on 4Å molecular sieve (4A) and MgAlO mixed oxides supports. The fresh catalysts were characterised and tested in the Suzuki–Miyaura reaction to test their activity, selectivity and stability. It was observed that while the Cu-Pd-4A-TSI catalyst kept its activity during six cycles that of the Cu-Pd-4A-CI dropped. On MgAlO support the catalyst prepared with CI proved to be stable even for six runs contrary to TSI. The active phase of the reaction – namely the Cu–Pd alloy with atomic ratio 1:1 - was determined with the help of catalyst characterisation of the recovered catalysts. This observation confirms that whatever the way of preparation or the support is, the key-point is the presence of Pd-Cu 1:1 particles to enhance the catalytic performances. A crucial difference between the MgAlO and 4A supported catalyst was found in the reaction time necessary for the Suzuki–Miyaura reaction. With the Cu-Pd-MgAl-CI catalyst the reaction time could be reduced to thirty minutes contrary to one hour with Cu-Pd-4A-TSI. Moreover it was concluded that with a more basic support the reduction of the quantity of the base was possible however it brought slightly decreasing yield. The Petasis-borono Mannich reaction was also performed in the presence of each mono-and bimetallic catalysts

L'objectif de ce travail est d'établir des relations entre chimie d'interface et propriétés mécaniques dans les assemblages bimétalliques. Il met en évidence que les mécanismes qui contrôlent le développement d'une interface entre alliage Al-Si et renfort ferreux ou titane ont une influence majeure sur les propriétés mécaniques de cette interface. La caractérisation mécanique des interfaces est réalisée par un test de flexion 4 points sur des lames bimétallique élaborées par aluminiage au trempé sur lesquelles un raidisseur est rapporté par collage ou surmoulage. L'évolution de la chimie de la zone de réaction interfaciale est provoquée par un traitement thermique à 535°C à différents temps. La caractérisation des zones de réaction ainsi que des chemins de fissuration est réalisée par diffraction des rayons X et microsonde électronique. Pour les interfaces Fe/A-S7G03 brutes d'élaboration, avant traitement thermique, l'analyse des essais mécaniques conduit à l'obtention d'une valeur du taux de restitution d'énergie de 23 J/m2 qui correspond à la propagation d'une fissure dans la phase η−Al5Fe2(Si). En ce qui concerne les interfaces Ti/A-S7G03, leur force n'a pas permis la propagation d'une fissure dans les conditions de l'essai. A la suite d'un traitement thermique à 535°C, les interfaces Fe/A-S7G03 sont fragilisées par le mécanisme de croissance de la couche de réaction interfaciale qui conduit à l'apparition de porosités Kirkendall en son sein. A l'inverse, dans le cas des interfaces Ti/A-S7G03, aucun affaiblissement de l'interface n'est associé au traitement thermique en raison d'un mécanisme de croissance différent.

The aim of the present thesis is to understand the phase transformation behavior of embedded alloy nanoparticles embedded in immiscible matrices. Embedded alloy inclusions have been dispersed in immiscible matrix via rapid solidification method. The present work deals with synthesis of embedded particles, evolution of microstructure, morphology and crystallographic orientation relation relationships among different phases, phase transformation and phase stability behavior of embedded alloy inclusions in different matrices. In the present investigation the systems chosen are Bi-Sn and Bi-Pb in Zn matrix and Cd-Sn in Al matrix. Chapter 1 gives the brief introduction of present work Chapter 2 gives a brief review of nanoscale materials, various synthesis techniques, microstructure evolution, solidification and melting theories. Chapter 3 discusses the processing and experimental techniques used for characterization of the different samples in the present work. Melt-spinning technique used to synthesize the rapidly solidified ribbons. The structural characterization is carried out using X-ray diffraction and transmission electron microscopy. Chapter 4 illustrates the size dependent solubility and phase transformation behavior of Sn-Cd alloy nanoparticles embedded in aluminum matrix. X-ray diffraction study shows the presence of fcc Al, bct Sn, hcp Cd solid solution and hcp Cd phases. Based on Zen’s law, the amount of Sn present Cd solid solution is estimated. Using overlapped sterograms, the orientational relationships among various phases are found. Microscopy studies reveal that majority of the alloy nano inclusions exhibit a cuboctahedral shape with 111 and 100 facets and they are bicrystalline. STEM-EDS analysis shows that both phases exhibit size dependent solubility behavior and for particles size smaller than 18 nm, single phase solid solution could only be observed. Calorimetric studies reveal a depression in eutectic melting point of bimetallic particles. In situ heating studies show that melting initiates at triple line junction corner and melt first grows into the interior of the Sn rich phase of the particle and then later the melt grows into the interior of the Cd phase of the particle. During cooling first Cd phase solidifies later Sn phase solidifies and on further cooling at low temperatures entire particle transforming into complete solid solution phase particle. Size dependent melting studies show that during heating smaller particles melted first, later bigger particles melted. During cooling first bigger particle solidified later smaller particles solidified. High resolution imaging indicates presence of steps across particle-matrix interface that may get annihilated during heating. During cooling, molten particles in the size range of 16-30 nm solidify as solid solution which for molten particles greater than 30 nm solidify as biphasic particle. Insitu heating studies indicates that for solid particles less than 15 nm get dissolved in the Al matrix at temperatures at around 135°C. Differential scanning calorimetry (DSC) studies show in the first heating cycle most of the particles melt with an onset of melting of at 166.8°C which is close to the bulk eutectic temperature of Sn-Cd alooy. The heating cycle reveals that the melting event is not sharp which can be understood from in-situ microscopy heating studies. In the second and the third cycles, the onset of melting observed at still lower temperatures 164.3°C and 158.5°C .The decrease in onset melting point in subsequent heating cycles is attributed to solid solution formation of all small particles whose size range below 30 nm during cooling. cooling cycles exhibit an undercooling of 90°C with respect to Cd liquidus temperature. Thermal cycling experiments using DSC were carried out by arresting the run at certain pre-determined temperatures during cooling and reheating the sample to observe the change in the melting peak position and area under the peak. The areas of these endothermic peaks give us an estimate of the fraction of the particles solidified upto the temperature when the cycling is reversed. Based on experimental observations, a thermodynamic model is developed, to understand the solubility behavior and to describe the eutectic melting transition of a binary Sn-Cd alloy particle embedded in Al matrix. Chapter 5 discusses the phase stability and phase transformation behavior of nanoscaled Bi-Sn alloys in Zn matrix. Bi-Sn alloys with eutectic composition embedded in Zn matrix using melt spinning technique. X-ray diffraction study shows the presence of rhombohedral Bi, pure BCT Sn and hcp Zn phases. In X-ray diffractogram, there are also other new peaks observed, whose peak positions (interplanar spacings) do not coincide either with rhombohedral Bi or bct Sn or hcp Zn. Assuming these new phase peaks belong to bct Sn rich solid solution(based on earlier work on Bi-Sn rapidly solidified metastable alloys) whole pattern fitting done on x-ray diffractogram using Lebail method. The new phase peaks indicated as bct M1(metastable phase1), bct M2(metastable phase2) phases. The amount of Bi present in M1, M2 solid solution is estimated using Zens law. Two sets of inclusions were found, one contains equilibrium bismuth and tin phases and the other set contains equilibrium bismuth and a metastable phase. In-situ TEM experiments suggest that as temperature increases bismuth diffuses into tin and becomes complete solid solution. Melting intiates along the matrix–particle interface leading to a core shell microstructure. During cooling the entire inclusion solidify as solid solution and decomposes at lower temperatures. High temperature XRD studies show that as temperature increases M1, M2 phases peaks merge with Sn phase peaks and Bi phase peak intensities slowly disappear and on further increasing temperature Sn solid solution phase peaks also disappear. During cooling diffraction studies show that first Sn solid solution phase peaks appear and later Bi phase peaks appear. But, the peaks belong to metstable phases not appeared while cooling. Chapter 6 presents morphology and phase transformation of nanoscaled bismuth-lead alloys with eutectic (Pb44.5-Bi55.5) and peritectic (Pb70-Bi30) compositions embedded in zinc matrix. using melt spinning technique. In alloy1[ Zn-2at%(Pb44.5-Bi55.5)] inclusions were found to be phase separated into two parts one is rhombohedral Bi and the other is hcp Pb7Bi3 phase. X-ray diffraction study shows the presence of rhombohedral Bi, hcp Pb7Bi3 and hcp Zn phases in Zn-2at%(Pb44.5-Bi55.5) melt spun sample. The morphology and orientation relationships among various phases have been found. In-situ microscpy heating studies show that melt initially spreads along the matrix–particle interface leading to a core-shell microstructure. And in the core of the core-sell particles, first Bi phase melts later Pb7Bi3 phase will melt and during cooling the whole particle solidify as biphase particle with large undercooling. In-situ heating studies carried out to study the size dependent melting and solidification behavior of biphase particles. During heating smaller particles melt melt first later bigger particle will melt. In contrast, while cooling smaller particles solidifies first, later bigger particles will solidify. Detailed high temperature x-ray diffraction studies indicate there increases first Bi phase peaks disappear later Pb7Bi3 phase peaks disappear and during cooling first Pb7Bi3 phase peaks appear and later Bi phase peaks appear. In alloy2[ Zn-2at%(Pb70-Bi30)] inclusions were found to be single phase particles. X-ray diffraction study shows the presence of hcp Pb7Bi3 and hcp Zn phases in Zn-2at%(Pb70-Bi30) melt spun sample. The crystallographic orientation relationship between hcp Pb7Bi3 and hcp Zn phases. In-situ microscpy heating studies show that melting initiates across the matrix–particle interface grows gradually into the interior of the particle. Three phase equilibrium at peritectic reaction temperature is not observed during insitu heating TEM studies. Size dependent melting point depression of single phase particles is not observed from in-situ heating studies. Detailed high temperature x-ray diffraction studies show that while heating the Pb7Bi3 phase peak intensities start decreasing after 170°C and become zero at 234°C. And during cooling Pb7Bi3 phase peaks starts appearing at 200°C and on further cooling the Pb7Bi3 phase peak intensities increase upto 150°C, below this temperature peak intensities remain constant.

博士
國立臺灣科技大學
化學工程系
99
This dissertation summarizes the author’s research efforts to synthesize Pt-based bimetallic alloy and core-shell nanostructured electrocatalysts for applications in direct methanol fuel cells (DMFCs) that can be applied to both their anode and cathode sides. The behavior of bimetallic Pt-based catalysts are fundamentally different to their counter-monometallic catalysts, i.e. Pt and M (M is the second metal, e.g. Pd, Cr, Co, Fe, Sn, Ru, etc.). The addition of the second metal to Pt significantly enhances the rate of electrochemical oxidation and/or reduction in fuel cells; thereby achieving the maximum activity, together with exceptional selectivity and stability. The state-of-the-art of bimetallic Pt-based catalysts is highly dependent on the composition, structure, morphology, particle size, degree of alloying, and other properties. Overall, Pt-based alloy and core-shell nanostructured catalysts are emerging as one of the most promising solutions to address the existing challenges in DMFCs, namely the cost of the catalysts (Pt as the ‘common catalyst’, but it is scarce and extremely expensive) and the sluggish nature of the Pt-kinetic activity with respect to both the anode and cathode reactions. In this dissertation, three synthesis methods have been developed and used to prepare three different Pt-based electrocatalysts with well-controlled sizes, structures, and compositions. Structurally these Pt-based alloyed electrocatalysts are carbon-supported Pt-Cr (Pt-Cr/C), and Pt-Ru (Pt-Ru/C) catalysts; while for the core-shell structure, a carbon-supported Pt-monolayered shell on a Pd-core (PdcorePtmonoshell/C) was developed. Since these catalysts have their own characteristics in the functionalities in the anode or cathode reactions, each of them will be discussed in detail as a separate topic. In the search for an alternative to core-shell structured nanoparticle catalysts, with an active Pt-monolayer, supported on the surface of a dimensionally-stable (PdcorePtmonoshell), here we report a kinetically-controlled autocatalytic chemical process, in which a sacrificial Cu-monolayer on Pd nanoparticles (NPs) is autocatalytically deposited under kinetically-controlled conditions and which is later displaced to form a Pt-monolayer via redox-transmetallation. This process is also adaptable for use as a general protocol for the fabrication of bimetallic core@shell structured NPs, some examples being: Pt@Pd, Ir@Pt, and Ir@Pd. Unlike the thermodynamically-controlled under-potential deposition (UPD) process, the method presented here allows for the scaling-up of production of well-defined core@monolayered shell Pd@Pt nanoparticles without the need for any additional reducing agents and/or electrochemical treatments. Having immediate and obvious commercial potential PdcorePtmonoshell/C NPs have been systematically characterized by in situ X-ray absorption (XAS), electrochemical-FTIR, transmission electron microscopy (TEM), and electrochemical techniques; both during synthesis, and subsequent testing in one particularly important catalytic reaction, namely the oxygen reduction reaction (ORR) which is pivotal in fuel cell operation. It was found that the bimetallic Pd@Pt NPs exhibited a significantly enhanced electrocatalytic activity, with respect to this reaction, in comparison with their monometallic counterparts. In the development of Pt-Cr/C catalysts, two different methods were used to prepare bimetallic Pt3Cr1/C nanocatalysts from similar compositions where the resulting materials exhibit different alloying extents (structure). We investigated how these variations in alloying extent impact the catalytic activity, stability, and selectivity in the ORR. One method, based on the slow thermal decomposition of the Cr precursor at a rate that matches the chemical reduction of the Pt precursor, allows fine control of the Pt3Cr1/C alloy’s composition; whereas the second approach, using the conventional ethylene glycol method results in considerable deviation (> 25%) from the projected composition. Consequently these two methods give variations in the alloying extent that has a strong influence on the Pt d-band vacancy and the Pt-electroactive surface area (Pt-ECSA). This relationship was systematically evaluated using TEM, XAS, and electrochemical analyses. The ORR activity depends on two effects that nullify each other, namely the number of active Pt-sites and their activity. Here the Pt-site activity dominates in governing the ORR activity. The nanocatalyst’s selectivity towards the ORR and the competitive methanol oxidation reaction (MOR) depend on these two effects acting in cooperation to give enhanced ORR activity with suppressed MOR. The number of active Pt-sites is associated with the Pt-ECSA value, while the Pt-site activity is associated with the alloying extent and Pt d-band vacancy (electronic) effects. The presence of Cr atoms in Pt3Cr1/C enhances stability during electrochemical treatment. Overall, the Pt3Cr1/C catalyst prepared by the controlled composition synthesis was shown to be superior in ORR activity, selectivity, and stability owing to its favorable alloying extent, Pt d-band vacancy, and Pt-ECSA. While for the development of Pt-Ru/C catalysts, a controlled composition–based method, i.e. the microwave-assisted ethylene glycol (MEG) method was successfully developed to prepare bimetallic PtxRu100–x/C nanocatalysts with different alloy compositions. This study highlights the impact of the variation in alloy composition of PtxRu100–x/C catalysts on their alloying extent (structure) and subsequently their catalytic activity toward the MOR. The alloying extent of these PtxRu100–x/C catalysts has a strong influence on their Pt d–band vacancy and Pt–ECSA: this relationship was systematically evaluated using XAS, scanning electron microscopy-coupled with energy dispersive X–ray spectroscopy, TEM, density functional theory calculations, and electrochemical analyses. The MOR activity depends the on the number and activity of the Pt-sites. Here the number of active Pt-sites is associated with the Pt–ECSA value, while the Pt–site activity is associated with the alloying extent and Pt d–band vacancy (electronic) effects. Among the PtxRu100–x/C nanocatalyts with various Pt:Ru atomic ratios (x= 25, 50, and 75), the Pt75Ru25/C nanocatalyst was shown to be superior with respect to the MOR activity owing to its favorable alloying extent, Pt d–band vacancy, and Pt–ECSA.

Transition metal alloys are an important class of materials in heterogeneous catalysis due in no small part to the often greatly enhanced activity and selectivity they exhibit compared to their monometallic constituents. A host of experimental and theoretical studies have demonstrated that, in many cases, these synergistic effects can be attributed to atomic-scale features of the catalyst surface. Realizing the goal of designing -- rather than serendipitously discovering -- new alloy catalysts thus depends on our ability to predict their atomic configuration under technologically relevant conditions. This dissertation presents original research into the development and use of computational tools to accomplish this objective. These tools are all based on a similar strategy: For each of the alloy systems examined, cluster expansion (CE) Hamiltonians were constructed from the results of density functional theory (DFT) calculations, and then used in Metropolis Monte Carlo (MC) simulations to predict properties of interest. Following a detailed description of the DFT+CE+MC simulation scheme, results for the AuPd/Pd(111) and AuPt/Pt(111) surface alloys are presented. These two systems exhibit considerably different trends in their atomic arrangement, which are explicable in terms of their interatomic interactions. In AuPd, a preference for heteronuclear, Au-Pd interactions results in the preferential formation of Pd monomers and other small ensembles, while in AuPt, a preference for homonuclear interactions results in the opposite. AuPd/Pd(100) and AuPt/Pt(100) were similarly examined, revealing not only the effects of the same heteronuclear/homonuclear preferences in this facet, but also a propensity for the formation of second nearest-neighbor pairs of Pd monomers, in close agreement with experiment. Subsequent simulations of the AuPd/Pd(100) surface suggest the application of biaxial compressive strain as a means increasing the population of this catalytically important ensemble of atoms. A method to incorporate the effects of subsurface atomic configuration is also presented, using AuPd as an example. This method represents several improvements over others previously reported in the literature, especially in terms of its simplicity. Finally, we introduce the dimensionless scaled pair interaction, whereby the finite-temperature atomic configuration of any bimetallic surface alloy may be predicted from a small number of relatively inexpensive calculations.
text

Investigations on size dependent phase stability and transformations in isolated nanoparticles have gained momentum in recent times. Size dependent phase stability generates size specific particle microstructure which consequently yields size specific functionality. One important prerequisite for conducting studies on nanoparticles is their synthesis. A substantial amount of research effort has therefore been focused on devising methodologies for synthesizing nanoparticles with controlled shapes and sizes. The present thesis deals with both these two aspects: (a) synthesis of nanoparticles and (b) phase transformations in nanoparticles. The system chosen in this study is AuCu intermetallic nanoparticles. The choice of AuCu nanoparticle was due to the fact that the literature contains abundance of structural and thermodynamic data on Au–Cu system which makes it a model system for investigating size dependence of phase transformations. With respect to synthesis, the present thesis provides methodologies for synthesizing alloyed Au–Cu nanoparticles of different sizes, Au–Cu nano-chain network structures and uniform Au–Cu2S hybrid nanoparticles. For every type, results are obtained from a detailed investigation of their formation mechanisms which are also presented in the thesis. With respect to phase transformation, the thesis presents results on the size dependence of fcc to L10 transformation onset in Au–Cu nanoparticles under isothermal annealing conditions. The present thesis is divided into eight chapters. A summary of results and key conclusions of work presented in each chapter are as follows. The ‘introduction’ chapter (chapter I) describes the organization of the thesis. Chapter II (literature study) presents a review of the research work reported in the literature on the various methodologies used for synthesizing Au–Cu based nanoparticles of different shapes and sizes and on ordering transformation in AuCu nanoparticles. The chapter also presents a brief discussion on the reaction variables that control the process of nucleation and growth of the nanoparticles in solution. Chapter III titled ‘experimental details and instrumentation’ describes the synthesis procedures that were used for producing various nanoparticles in the present work. The chapter also briefly describes the various characterization techniques that were used to investigate the nanoparticles. The fourth chapter titled ‘synthesis and mechanistic study of different sizes of AuCu nanoparticles’ provides two different methodologies for synthesis, referred as ‘two-stage process’ and ‘two-step process’ that have been used for producing alloyed AuCu nanoparticles of different sizes (5, 7, 10, 14, 17, 25 nm). The ‘two-stage’ process involved sequential reduction of Au and Cu precursors in a one pot synthesis process. Whereas, the ‘two-step’ process involved a two-pot synthesis in which separately synthesized Au nanoparticles were coated with Cu to generate alloyed AuCu nanoparticles. In the two-stage synthesis process it was observed that by changing the total surfactant-to-metal precursor molar ratio, sizes of the alloyed AuCu nanoparticles can be varied. ‘Total surfactants’ here include equal molar amounts of oleic acid and oleylamine surfactants. Interestingly, it was observed that there exists a limitation with respect to the minimum nanoparticle size that can be achieved by using the two-stage process. The minimum AuCu nanoparticle size achieved using the two-stage synthesis process was 14 nm. Mechanism of formation of AuCu nanoparticles in the two-stage synthesis process was investigated to find out the reason for this size limitation and also to determine how the synthesis process can be engineered to synthesize alloyed AuCu nanoparticles with smaller (<14nm) sizes. Studies to evaluate mechanism of synthesis were conducted by investigating phase and size of nanoparticles present in the reaction mixture extracted at various stages of the synthesis process. Their studies revealed that (a) the nanoparticle formation mechanism in the two-stage synthesis process involves initial formation of Au nanoparticles followed by a heterogeneous nucleation and diffusion of Cu atoms into these Au rich seeds to form Au–Cu intermetallic nanoparticles and (b) by increasing the relative molar amount of the oleylamine surfactant, size of the initial Au seed nanoparticles can be further reduced from the minimum size that can be achieved in the case when equal molar amounts of oleylamine and oleic acid surfactants are used. The information obtained from the mechanistic study was then utilized to design the two-step synthesis process. In the two-step process, Au nanoparticles were synthesized in a reaction mixture containing only the oleylamine surfactant. Use of only oleylamine resulted in production of pure Au nanoparticles with sizes that were well below 10 nm. These Au nanoparticles were washed and dispersed in a solution containing Cu precursor. Introduction of a reducing agent into this reaction mixture led to the heterogeneous nucleation of Cu onto the Au seed particles and their subsequent diffusion into them to form alloyed AuCu nanoparticles with sizes of ~5, 7 and 10 nm. The study present in this chapter essentially signified that the surfactants used in the reaction mixture not only prevent nanoparticles from agglomerating in the final dispersion but also control their nucleation and growth and therefore can be used as a tool to tune nanoparticle sizes. The fifth chapter titled ‘size dependent onset of FCC-to-L10 transformations in AuCu alloy nanoparticles’ illustrates the effect of AuCu nanoparticle size on the onset of ordering under isothermal annealing conditions. Nanoparticles in this study were annealed in-situ in a transmission electron microscope. Samples were prepared by drop drying a highly dilute dispersion of as-synthesized nanoparticles onto an electron transparent TEM grid. Nanoparticles sitting on the TEM grid were well separated from each other to minimize particle sintering during the annealing operation. It was however observed that during the isothermal annealing, particle coarsening due to atomic diffusion was appreciable for 5 nm particles but negligible for 7 and 10 nm particles. Therefore for this study only 7 nm and 10 nm sized particles were considered. Onset of ordering was determined from the time when first sign of the diffraction spot, corresponding to the ordered phase, appears in the selected area electron diffraction pattern from a region containing large number of AuCu nanoparticles. Through a series of isothermal experiments it was observed that the time for onset of ordering increased with decrease in size of the nanoparticles. It is speculated that the delay in onset of ordering may be due to the fact that with a decrease in nanoparticle size the probability of a nanoparticle containing a fluctuation that shall generate a thermodynamically stable nuclei of the ordered phase decreases. A sharp interface between the ordered and the disordered phase inside the particle was also observed which suggested that the ordering transformation in as-synthesized fcc AuCu nanoparticles is a first order transformation. The sixth chapter titled ‘synthesis and characterization of Au1-xCux–Cu2S hybrid nanostructures: morphology control by reaction engineering’ provides a modified polyol method based synthesis strategy for producing uniform Au–Cu2S hybrid nanoparticles. Detailed compositional and structural characterization revealed that the hybrid nanoparticles are composed of cube shaped Au-rich, Au–Cu solid solution phase and hemispherical shaped Cu2S phase. Interestingly, the hemispherical Cu2S phase was attached to only one facet of the cube shaped phase. A study on the formation mechanism of hybrid nanoparticles was also conducted by characterizing specimens extracted from the reaction mixture at different stages of the synthesis process. The study revealed that the mechanism of formation of hybrid nanoparticles involved initial formation of isolated cube shaped pure Au nanoparticles and Cu–thiolate complex with a sheet morphology. With increase in time at 180°C, the Cu–thiolate complex decomposed and one part of the Cu atoms that were produced from the decomposition were utilized in forming the spherical Cu2S and other part diffused into the Au nanoparticles to form Au–Cu solid solution phase. The chapter also presents a study on the effect of dodecanethiol (DDT) on achieving the hemisphere-on-cube hybrid morphology. In this study it is illustrated that an optimum concentration of dodecanethiol is required both for achieving size and morphological uniformity of the participating phases and for their attachment to form a hybrid nanoparticle. The seventh chapter titled ‘synthesis of Au–Cu nano-chains network and effect of temperature on morphological evolution’ provides methodology for synthesizing fcc Au– Cu nano-chain network structures using polyvinylprrolidone (PVP) surfactant. It was observed that with increase in the molar amount of PVP in the reaction mixture, morphology of the as-synthesized product gradually changed from isolated nanoparticles to branched nano-chain like. The nano-chains contained twins which indicated an absence of continuous growth and possibility of growth by oriented attachment of initially formed Au–Cu nanoparticles. Both in-situ and ex-situ annealing of the nano-chains led to their decomposition into isolated nanoparticles of varying sizes. Annealing also caused fcc-to¬L10 phase transformation. Investigation of the wave length of perturbation leading to breaking of a nano-chain into particles indicated that the surface energy anisotropy affects the splitting of nano-chain network structure into nano-sized particles. The thesis ends with a last chapter where we have presented possible future extension of current work.

In recent decades, alternatives to traditional coal and fossil fuels were utilized to reduce carbon emissions. Among these alternatives, natural gas is a cleaner fuel and is abundant globally. Shale gas, a form of natural gas that also contains light alkanes (C2-C4), is presently being employed to produce olefins, which can be upgraded to higher molecular weight hydrocarbons. This thesis describes efforts to develop new catalytic materials and characterizations for the conversion of shale gas to fuels.

In the first half, silica supported Pt-Cr alloys containing varying compositions of Pt and Pt₃Cr were used for propane dehydrogenation at 550°C. Although a change in selective performance was observed on catalysts with varying promoter compositions, the average nano-particle structures determined by in situ, synchrotron x-ray absorption spectroscopy (XAS) and x-ray diffraction (XRD) were identical. Further, this work presents a method for the characterization of the catalytic surface by these methods to understand its relationship with olefin selectivity. From this, we can gain an atomically precise control of new alloys compositions with tunable surface structures.

Once formed by dehydrogenation, the intermediate olefins are converted to fuel-range hydrocarbons. In the second half, previously unknown single site, main group Zn²⁺ and Ga³⁺ catalysts are shown to be effective for oligomerization and the resulting products follow a Schutlz Flory distribution. Mechanistic studies suggest these catalysts form metal hydride and metal alkyl reaction intermediates and are active for olefin insertion and b-H elimination elementary steps, typical for the homogeneous, Cossee-Arlman oligomerization mechanism. Evidence of metal hydride and metal alkyl species were observed by XAS, Fourier transform infrared spectroscopy (FTIR), and H₂/D₂ isotope exchange. Understanding the reaction intermediates and elementary steps is critical for identifying novel oligomerization catalysts with tunable product selectivity for targeted applications.

Through controlled synthesis and atomic level in situ characterizations, new catalysts compositions can be developed with high control over the resulting performance. An atomically precise control of the catalyst structure and understanding how it evolves under reaction conditions can help shed light on the fundamental principles required for rational catalyst design.

博士
國立臺灣師範大學
化學系
100
Abstract 1st part: The interaction of NOx on Ni(111) surface investigated with quantum-chemical calculations We applied periodic density-functional theory to investigate the interaction of NOx on Ni(111) surface for small and large coverages. For a small coverage, adsorbed species such as NO, N2O and NO2 tend to dissociate to form atomic N and atomic O on the surface, but a large barrier, 2.34 eV, hinders the recombination of adsorbed N to form N¬2. At a large coverage, the recombination of N and NO to form N2O is favorable; this species might either desorb or break the N-O bond to form N2. Our calculated results agree satisfactorily with experimental observations. The formation of N2 via paths that vary with coverage is analyzed and discussed.   2nd part: The NO reaction on Ni-Pt bimetallic surfaces investigated with theoretical calculations We applied periodic density-functional theory to investigate the adsorption and dissociation of NO on bimetallic surfaces, including the xNi@Pt(111), NixPt4-x(111), and (4–x)Pt@Ni(111) surfaces ( x = 0~4). For all bimetallic surfaces, NO is preferentially adsorbed on Ni-rich sites, and the adsorption energies increase with the increasing number of top-layer Ni atoms on the surface. When the top-layer compositions are equal (but with varied composition of inner layers), the adsorption energy of NO on these surfaces decreases in the order xNi@Pt(111) > NixPt4-x(111) > (4 – x) Pt@Ni(111), whereas the NO dissociation barriers increase in the opposite order; a larger adsorption energy of NO leads to a smaller NO dissociation barrier. We employed the local density of states to study the inner-layer effect of the various surfaces, and found that the inner-layer Pt atoms of the 4Ni@Pt(111) surface caused the greatest up-shift of the d-band center (of top-layer Ni atoms) toward the Fermi energy.   3rd part: The CO2 reaction on WC(0001) and WC-Co alloy surfaces investigated with theoretical calculations We applied periodic density-functional theory to investigate the adsorption of CO2 on WC(0001) and various WC-Co alloy surfaces, and discussed the reaction trend of CO2 dissociation or hydrogenation on these surfaces. We employed the electron localization function, ELF to study the electron localization or delocalization effect of the various Co-ratio WC-Co alloy surfaces, and found that the partial-delocalization surfaces (WC-Co(0.25ML) surface) exhibit largest adsorption energy to CO2 molecule (–1.61 eV) in all of our calculated surfaces. Incidentally, when we increased the Co-ratio to form WC-2Co(0.50ML) surface, the activation energy of CO2 dissociation (CO2→CO+O) was reduced to 0.57 eV; it also decrease the CO2 hydrogenation, CO2+H → HCOO (formate), due to the cause of electron delocalization on the increased Co-ratio WC-Co alloy surfaces.

Among various nanomaterials, metal nanoparticles are the widely studied ones because of their pronounced distinct properties arising in the nanometer size regime, which can be tailored easily by tuning predominantly their size and shape. During the past few decades, scientists are engaged in developing new synthetic methodologies for the synthesis of metal nanoparticles which can be divided into two broad categories: i) top-down approach, utilizing physical methods and ii) bottom-up approach, employing chemical methods. As the chemical methods offer better control over particle size, numerous chemical methods have been developed to obtain metal nanoparticles with narrow size distribution. However, these two approaches have their own merits and demerits; they are not complementary to each other and also not sustainable for real time applications. Recent focus on the synthesis of metal nanoparticles is towards the development of green and sustainable synthetic methodologies. A solid state route is an exciting prospect in this direction because it eliminates usage of organic solvents thus, makes the overall process green and at the same time leads to the realization of large quantity of the materials, which is required for many applications. However, the major obstacle associated with the development of a solid state synthetic route is the lack of fundamental understanding regarding the formation mechanism of the nanoparticles in the solid state. Additionally, due to the heterogeneity present in the solid mixture, it is very difficult to ensure the proximity between the capping agent and nuclei which plays the most decisive role in the growth process. Recently, employment of amine–borane compounds as reducing agents emerged as a better prospect towards the development of sustainable synthetic routes for metal nanoparticles because they offer a variety of advantages over the traditional borohydrides. Being soluble in organic medium, amine– borane allows the reaction to be carried out in a single phase and due to its mild reducing ability a much better control over the nucleation and growth processes is realized. However, the most exciting feature of these compounds is that their reducing ability is not only limited to the solution state, they can also bring out the reduction of metal ions in the solid state. With the availability of a variety of amine–boranes of varying reducing ability, it opens up a possibility to modulate the nanostructure in both solid and solution states by a judicious choice of reducing agent. Although our current understanding regarding the growth behavior of nanoparticles has advanced remarkably, however, most often it is some classical model which is invoked to understand these processes. With the recent developments in in situ transmission electron microscopy techniques, it is now possible to unravel more complex growth trajectories of nanoparticles. These studies not only expand the scope of the present knowledge but also opens up possibilities for many future developments. Objectives • To develop an atom economy solid state synthetic methodology for the synthesis of metal nanoparticles employing amine–boranes as reducing agents. • To gain a mechanistic insight into the formation mechanisms of nanoparticles in the solid state by using amine–boranes with differing reducing ability. • Synthesis of bimetallic nanoparticles as well as supported metal nanoparticles in the solid state using ammonia borane as the reducing agent. • To develop a new in situ seeding growth methodology for the synthesis of core@shell nanoparticles composed of noble metals by employing a very weak reducing agent, trimethylamine borane and their transformation to their thermodynamically stable alloy counterparts. • Synthesis of highly monodisperse ultra-small colloidal calcium nanoparticles with different capping agents such as hexadecylamine, octadecylamine, poly(vinylpyrrolidone) and a combination of hexadecylamine/poly(vinylpyrrolidone) using the solvated metal atom dispersion (SMAD) method. To study the coalescence behavior of a pair of calcium nanoparticles under an electron beam by employing in situ TEM technique. Significant results An atom economy solid state synthetic route has been developed for the synthesis of metal nanoparticles from simple metal salts using amine–boranes as reducing agents. Amine–borane plays a dual role here: acts as a reducing agent thus brings out the reduction of metal ions and decomposes simultaneously to generate B-N based compounds which acts as a capping agent to stabilize the particles in the nanosize regime. This essentially minimizes the number of reagents used and hence simplifying and eliminating the purification procedures and thus, brings out an atom economy to the overall process. Additionally, as the reactions were carried out in the solid state, it eliminates use of organic solvents which have many adverse effects on the environment, thus makes the synthetic route, green. The particle size and the size distribution were tuned by employing amine–boranes with differing reducing abilities. Three different amine–boranes have been employed: ammonia borane (AB), dimethylamine borane (DMAB), and trimethylamine borane (TMAB) whose reducing ability varies as AB > DMAB >> TMAB. It was found that in case of AB, it is the polyborazylene or BNHx polymer whereas, in case of DMAB and TMAB, the complexing amines act as the stabilizing agents. Several controlled studies also showed that the rate of addition of metal salt to AB is the crucial step and has a profound effect on the particle size as well as the size distribution. It was also found that an optimum ratio of amine–borane to metal salt is important to realize the smallest possible size with narrowest size distribution. Whereas, use of AB and TMAB resulted in the smallest sized particles with best size distribution, usage of DMAB provided larger particles that are also polydisperse in nature. Based on several experiments along with available data, the formation mechanism of metal nanoparticles in the solid state has been proposed. Highly monodisperse Cu, Ag, Au, Pd, and Ir nanoparticles were realized using the solid state route described herein. The solid state route was extended to the synthesis of bimetallic nanoparticles as well as supported metal nanoparticles. Employment of metal nitrate as the metal precursor and ammonia borane as the reducing agent resulted in highly exothermic reaction. The heat evolved in this reaction was exploited successfully towards mixing of the constituent elements thus allowing the alloy formation to occur at much lower temperature (60 oC) compared to the traditional solid state metallurgical methods (temperature used in these cases are > 1000 oC). Synthesis of highly monodisperse 2-3 nm Cu/Au and 5-8 nm Cu/Ag nanoparticles were demonstrated herein. Alumina and silica supported Pt and Pd nanoparticles have also been prepared. Use of ammonia borane as the reducing agent in the solid state brought out the reduction of metal ions to metal nanoparticles and the simultaneous generation of BNHx polymer which encapsulates the metal (Pt and Pd) nanoparticles supported on support materials. Treatment of these materials with methanol resulted in the solvolysis of BNHx polymer and its complete removal to finally provide metal nanoparticles on the support materials. An in situ seeding growth methodology for the synthesis of bimetallic nanoparticles with core@shell architecture composed of noble metals has been developed using trimethylamine borane (TMAB) as the reducing agent. The key idea of this synthetic procedure is that, TMAB being a weak reducing agent is able to differentiate the smallest possible window of reduction potential and hence reduces the metal ions sequentially. A dramatic solvent effect was noted in the preparation of Ag nanoparticles: Ag nanoparticles were obtained at room temperature when dry THF was used as the solvent whereas, reflux condition was required to realize the same using wet THF as the solvent. However, no such behavior was noted in the preparation of Au and Pd nanoparticles wherein Au and Pd nanoparticles were obtained at room temperature and reflux conditions, respectively. This difference in reduction behavior was successfully exploited to synthesize Au@Ag, Ag@Au, and Ag@Pd nanoparticles. All these core@shell nanoparticles were further transformed to their alloy counterparts under very mild conditions reported to date. Highly monodisperse, ultrasmall, colloidal Ca nanoparticles with a size regime of 2-4 nm were synthesized using solvated metal atom dispersion (SMAD) method and digestive ripening technique. Hexadecylamine (HDA) was used as the stabilizing agent in this case. Employment of capping agent with a longer chain length, octadecylamine afforded even smaller sized particles. However, when poly(vinylpyrrolidone) (PVP), a branched chain polymer was used as the capping agent, agglomerated particles were realized together with small particles of 3-6 nm. Use of a combination of PVP and HDA resulted in spherical particles of 2-3 nm size with narrow size distribution. Growth of Ca nanoparticles via colaesence mechanism was observed under an electron beam. Employing in situ transmission electron microscopy technique, real time coalescence between a pair of Ca nanoparticles were detected and details of coalescence steps were analyzed.

Recent advancements in nanotechnology and emerging applications of nanomaterials in various fields have stimulated interest in fundamental scientific research dealing with the size and structure controlled synthesis of nanoparticles. The unique properties of nanoparticles are largely size dependent which could be tuned further by varying shape, structure, and surface properties, etc. The preparation of monodisperse nanoparticles is desirable for many applications due to better control over properties and higher performance compared to polydispersity nanoparticles. There are several methods for the synthesis of nanoparticles based on top-down and bottom-up approaches. The main disadvantage of top-down approach is the difficulty in achieving size control. Whereas, uniform nanoparticles with controllable size could be obtained by chemical methods but most of them are difficult to scale up. Moreover, a separate step of size separation is necessary in order to achieve monodispersed which may lead to material loss. In this context, a post-synthetic size modification process known as digestive ripening is highly significant. In this process, addition of a capping agent to poly disperse colloid renders it highly monodisperse either under ambient or thermal conditions. In addition to size control, digestive ripening is also effective in controlling the structure of nanoparticles in colloidal solution comprising two different elements. Use of co-digestive ripening strategy in conjunction with solvated metal atom dispersion (SMAD) method of synthesis resulted in hetero structures such as core–shell, alloy, and composite nanoparticles. Despite the versatility of digestive ripening process, the underlying mechanism in controlling size and structure of nanoparticles are not understood to date. The aim of this thesis is to gain mechanistic insight into size control of digestive ripening as well as to investigate structure control in various binary systems. Objectives  Study digestive ripening of Au nanoparticles using various alkyl amines to probe the mechanism  Study co-digestive ripening of binary colloids consisting of two metals, Pd and Cu prepared separately by SMAD method  Study co-digestive ripening of binary colloids consisting of a metal (Au) and a semiconductor (CdS) prepared separately by SMAD method  Study vaporization of bulk brass in SMAD reactor and analyse phase, structure, and morphology of various Cu/Zn bimetallic nanoparticles obtained from bulk brass under various experimental conditions Significant results In chapter 1, fundamental processes of nanoparticle formation and common synthetic techniques for the preparation of monodisperse nanoparticles are briefly discussed. Chapter 2 presents a mechanistic study of digestive ripening process with regard to size control using Au nanoparticles as a model system. Three long chain alkyl amine molecules having different chain length were used as digestive ripening agents. The course of digestive ripening process was analysed by UV-visible spectroscopy and transmission electron microscopy. The experimental conditions such as concentration of digestive ripening agent, time, and temperature were found to influence the size distribution of nanoparticles. The average particle size was found to be characteristic of metal-digestive ripening agent combination which is considered as the optimum size preferred during digestive ripening under a given set of experimental conditions. This study discusses stabilization of optimum sized particles, surface etching, and reversibility in digestive ripening. Chapter 3 describes the synthesis and characterization of PdCu alloy nanoparticles by co-digestive ripening method. Syntheses of individual Pd and Cu colloids were carried out by SMAD method. Pd nanoparticles obtained using THF as solvent and in the absence of any capping agent resulted in an extended small Pd nanowire network assembly. Morphological evolution of spherical Pd nanoparticles from Pd nanowire network structure was observed with the use of capping agent, hexadecyl amine (HDA) in SMAD method. Co-digestive ripening of Pd and Cu colloids was studied at various temperatures. This study revealed temperature dependent diffusion of Cu atoms into Pd lattice forming PdCu alloy nanoparticles. Next, co-digestive ripening of a colloidal system comprising a metal and a semiconductor was explored. Au-CdS combination was chosen for this study owing to its interesting photocatalytic properties. Chapter 4 deals with the synthesis of Au and CdS nanoparticles by SMAD method and Au/CdS nanocomposite by co-digestive ripening. CdS nanoparticles of size 4.0 + 1.2 nm and Au nanoparticles of size 5.6 + 1.1 nm were obtained as a result of digestive ripening process. Au/CdS nanocomposite obtained by co-digestive ripening was characterized by a matrix-like structure made up of CdS nanoparticles in which Au nanoparticles were embedded. CdS nanoparticles were found to establish an intimate surface contact with Au nanoparticles and the matrix of CdS surrounding Au was developed via aggregation during digestive ripening. Chapter 5 describes a comprehensive study on various Cu/Zn bimetallic nanoparticles obtained from bulk brass. Vaporization of bulk brass in SMAD reactor led to a deploying process and further growth of nanoparticles from phase separated Cu and Zn atoms formed a composite structure. The characterization of Cu/Zn nanocomposite revealed covering of composite surface with Cu resulting in a core-shell structure, Cu/Zn@Cu. Post-synthetic digestive ripening of these core-shell composite particles showed diffusion of Zn atoms to the composite surface in addition to size and shape modification. Annealing of Cu/Zn nanocomposites prepared in THF resulted in α-CuZn alloy nanoparticles via sequential transformation through η-CuZn5, γ-Cu5Zn8, and β-CuZn (observed as marten site) phases.