Auswahl der wissenschaftlichen Literatur zum Thema „Zařízení pro testování diferenciálů“

This master’s thesis deals with the design of equipment for testing differentials. The aim of the thesis is therefore the design of a special device that will be able to measure the steady and transient characteristics of differentials. Master’s thesis is divided into four chapters. The first chapter points out the disadvantages of fully open and closed differentials, the second deals with a basic overview of the structures and design of self-locking differentials. The third chapter deals with research of existing devices that test and measure the characteristics of differentials. The fourth chapter then discusses the possible drives of the tested unit. The fifth chapter focuses on the actual construction design of the test equipment. The subsequent sixth chapter then solves the strength calculations of the chosen structural elements of this device.

The thesis introduces the design of a test device for preassembled mechatronic cylindrical locks. The device is designed to test the mechanical and electronic parts which ensure minimisation of loss caused by poor preassembling or defect due to electronic parts. Since the defect will only come to realisation upon the complete product testing, the time of complete dismounting, exchange and assembly of the mechatronic parts would be saved and also time required for the final test of the whole product on the device would be saved.

This thesis is focused on the design of system for automated testing of hardware on Beagle Bone Black platform. The purpose of this thesis is to develop a complex device which will be able to test the functionality of general electronic devices before completion. Use the external measuring devices and design hardware to control them.

Goal of this thesis is to specify needed upgrades of current aparatus used for measuring parameters of thermoelectic modules, witch was constructed at the Enegry institute of Faculty of Mechanical Engineering, Brno University of Technology. In this theseis current state of aparatus where reviewed and specifications for updates where made. These specifications where used to create plans for new aparatus. Quality of designed aparatus where verified by simulations made in ANSYS. Plans for proposed aparatus where made.

This master’s thesis deals with the design and manufacture of device for testing and verification of functionality of atmospheric resistors produced by IMI CCI Czech Republic. An atmospheric resistor, also called disk stack, is a stack of disks through which the medium flows and the system of labyrinths in disk stack causing a pressure reduction of medium. This thesis describe design of the mechanical parts of stand for atmospheric resistors, choice pneumatic circuit’s components, data acquisition hardware for measuring flow, inlet and outlet pressure, and temperature. The software was created in LabVIEW programming environment. In the end of this paper was done measurement in order to test functionality of test stand and software.

Diplomová práce se zabývá možnosti kalibrace experimentálního testovacího zařízení. Zejména se věnuje návrhu termálního matematického modelu popisujícího tepelné procesy uvnitř zařízení v průběhu měření tepelné vodivosti vzorku. První část práce je věnována seznámení se s testovacím zařízením, jeho limity a principem měření. Popisuje řešení třetí verze testovací komory, společně s nezbytnými úpravami, provedenými za účelem zajištění předepsaných simulačních podmínek. Zmiňuje také potřebu a důvody kalibrace. Druhá část je především zaměřená na návrh kalibračních vzorků a termálního modelu. Uvádí definované požadavky a konečné vlastnosti vyrobených vzorků. Matematický model prezentuje postup výpočtu zjištěných tepelných ztrát a poukazuje na možnosti jejich zpřesnění. Testování kalibračních vzorků bylo provedeno na nově zprovozněné třetí verzi testovací komory. Naměřené výsledky poslouží k ladění termálního modelu, nezbytného k dokončení kalibračního procesu, který umožní přikročení k další fázi testování v experimentální komoře.

This diploma thesis is dedicated to mechnical desing, fabrication and assembly of experimental bearing testing rig. First part of the document contains research of current knowlege in the field of bearing testing and desings of currently used machines. In second part is conception of the testing rig described. Third part contains description of design variations that were designed. In Discussion is comented choices of final variants. Last part is dedicated to functional verification of the whole testing rig by first series of the tests.

This thesis deals with the structural design of a test rig for combustion engine bearings with static and dynamic loading capabilities. The first part of thesis summarizes materials, geometries and possible bearing failures, then analyzes existing test rigs. The second part contains different solutions and summarizes these solutions to a final design. The last part contains analysis of possible failure of the test rig and solutions for these problems. The thesis contains drawings prepared for manufacturing and a design report.

This diploma thesis deals with the design and implementation of a computer-controlled device for testing gas boiler control units, especially in the development phase. The reason for creating a test facility is the inadequacy of older test systems and the automation of existing testing. The test device in development consists of individual different cards. Each of the cards inserted into the motherboard performs its function in the system. Each of the cards has a special functionality which simulates the real conditions of the developed product. The basis of most cards is a microcontroller with a Cortex-M core, which communicates with the connected computer using the MODBUS protocol on the RS-485 communication interface. All cards on the bus are connected in parallel and behaves as a SLAVE, while the computer behaves as a MASTER and requests data or sends commands to the cards. The cards represent status switches (switching sensors), resistance and analog temperature sensors, PWM inputs and outputs (for simulation of feedback pumps or flow meters with pulse output). The cards also include a flame simulator, which reliably simulates the electrical properties of the flame and at the same time acts as a fan simulator. The input of the control unit is taken care of by the input card, which is intended for digital detection of the voltage presence in the range of 5 to 230 V DC and AC. Simultaneously, a card for connecting the power supply at zero voltage and disconnecting at zero current is created to supply the tested device with alternating voltage. A schematic diagram was designed or simulated for each card, then the function was verified and on this basis the whole card was created, including the microcontroller firmware. The most suitable solution and function of each card is carefully described and evaluated. All the requirements of the assignment within the work were met and the whole test equipment was manufactured and verified in four versions. In the future, the device is ready for the implementation of an automatic flame simulator and other improvements of individual module cards.