Auswahl der wissenschaftlichen Literatur zum Thema „Tungstene carbide“
Geben Sie eine Quelle nach APA, MLA, Chicago, Harvard und anderen Zitierweisen an
Inhaltsverzeichnis
Machen Sie sich mit den Listen der aktuellen Artikel, Bücher, Dissertationen, Berichten und anderer wissenschaftlichen Quellen zum Thema "Tungstene carbide" bekannt.
Neben jedem Werk im Literaturverzeichnis ist die Option "Zur Bibliographie hinzufügen" verfügbar. Nutzen Sie sie, wird Ihre bibliographische Angabe des gewählten Werkes nach der nötigen Zitierweise (APA, MLA, Harvard, Chicago, Vancouver usw.) automatisch gestaltet.
Sie können auch den vollen Text der wissenschaftlichen Publikation im PDF-Format herunterladen und eine Online-Annotation der Arbeit lesen, wenn die relevanten Parameter in den Metadaten verfügbar sind.
Zeitschriftenartikel zum Thema "Tungstene carbide"
Idrees, Maria, Husnain Ahmad Chaudhary, Arslan Akbar, Abdeliazim Mustafa Mohamed und Dina Fathi. „Effect of Silicon Carbide and Tungsten Carbide on Concrete Composite“. Materials 15, Nr. 6 (10.03.2022): 2061. http://dx.doi.org/10.3390/ma15062061.
Der volle Inhalt der QuelleZhong, Li Sheng, Yun Hua Xu, Peng Yu, Xiao Jie Liu, Fang Xia Ye und Hong Hua Yan. „Microstructure and Abrasive Wear Characteristics of In Situ WC Bundles – Reinforced Iron Matrix Composites“. Advanced Materials Research 284-286 (Juli 2011): 265–68. http://dx.doi.org/10.4028/www.scientific.net/amr.284-286.265.
Der volle Inhalt der QuellePu, Juan, Yu-Bo Sun, Lei Wu, Peng He und Wei-Min Long. „Effect of CeO2 Content on Microstructure and Properties of Ni-Based Tungsten Carbide Layer by Plasma Arc Cladding“. Coatings 12, Nr. 3 (06.03.2022): 342. http://dx.doi.org/10.3390/coatings12030342.
Der volle Inhalt der QuelleNovoselova, Inessa, Serhii Kuleshov, Anatoliy Omel’chuk, Valerii Bykov und Olena Fesenko. „ELECTROREDUCTION OF DITUNGSTATE AND CARBONATE ANIONS IN CHLORIDE MELT“. Ukrainian Chemistry Journal 87, Nr. 12 (21.01.2022): 97–108. http://dx.doi.org/10.33609/2708-129x.87.12.2021.97-108.
Der volle Inhalt der QuelleGezerman, Ahmet Ozan, und Burcu Didem Çorbacıoğlu. „Effects of Mechanical Alloying on Sintering Behavior of Tungsten Carbide-Cobalt Hard Metal System“. Advances in Materials Science and Engineering 2017 (2017): 1–11. http://dx.doi.org/10.1155/2017/8175034.
Der volle Inhalt der QuelleLu, Hao, Chong Zhao, Haibin Wang, Xuemei Liu, Rong Yu und Xiaoyan Song. „Hardening tungsten carbide by alloying elements with high work function“. Acta Crystallographica Section B Structural Science, Crystal Engineering and Materials 75, Nr. 6 (08.11.2019): 994–1002. http://dx.doi.org/10.1107/s2052520619012277.
Der volle Inhalt der QuelleTarraste, Marek, Jakob Kübarsepp, Arvo Mere, Kristjan Juhani, Märt Kolnes und Mart Viljus. „Ultrafine Cemented Carbides with Cobalt and Iron Binders Prepared via Reactive In Situ Sintering“. Solid State Phenomena 320 (30.06.2021): 176–80. http://dx.doi.org/10.4028/www.scientific.net/ssp.320.176.
Der volle Inhalt der QuelleГорленко, Александр, Aleksandr Gorlenko, Сергей Давыдов und Sergey Davydov. „Material implantation techniques based on tungsten carbide to increase friction surface durability“. Science intensive technologies in mechanical engineering 1, Nr. 9 (23.08.2016): 3–9. http://dx.doi.org/10.12737/21233.
Der volle Inhalt der QuelleLima, Maria Jose S., M. V. M. Souto, A. S. Souza, M. M. Karimi, F. E. S. Silva, Uilame Umbelino Gomes und Carlson P. de Souza. „Synthesis of Nanostructured Tungsten Carbide (WC) from Ammonia Paratungstate-APT and its Characterization by XRD and Rietveld Refinement“. Materials Science Forum 899 (Juli 2017): 31–35. http://dx.doi.org/10.4028/www.scientific.net/msf.899.31.
Der volle Inhalt der QuelleWu, Yung-Yi, und Dong-Yea Sheu. „Investigating Tungsten Carbide Micro-Hole Drilling Characteristics by Desktop Micro-ECM with NaOH Solution“. Micromachines 9, Nr. 10 (11.10.2018): 512. http://dx.doi.org/10.3390/mi9100512.
Der volle Inhalt der QuelleDissertationen zum Thema "Tungstene carbide"
Roure, Sophie. „Densification des mélanges de poudres WC-Co : de la compression au frittage“. Grenoble INPG, 1996. http://www.theses.fr/1996INPG0222.
Der volle Inhalt der QuelleHarry, Emmanuelle. „Stabilité mécanique et modes d'endommagement de revêtements multicouches à base de tungstène et de tungstène-carbone élaborés par PVD“. Grenoble INPG, 1998. http://www.theses.fr/1998INPG0071.
Der volle Inhalt der QuelleLavergne, Olivier. „Mécanismes de dissolution et de précipitation dans les carbures cémentés WC/Co“. Grenoble INPG, 1997. http://www.theses.fr/1997INPG0214.
Der volle Inhalt der QuelleLindahl, Bonnie. „Equilibrium Study of Chromium Containing Cemented Carbides : Solubility of chromium in tungsten carbide and η-phase“. Thesis, KTH, Materialvetenskap, 2010. http://urn.kb.se/resolve?urn=urn:nbn:se:kth:diva-49974.
Der volle Inhalt der QuelleGuiz, Robin. „Influence d’additions de titane/tungstène et de vanadium sur la précipitation de carbures secondaires au sein d’alliages modèles de type HP“. Thesis, Lyon, 2016. http://www.theses.fr/2016LYSEM011/document.
Der volle Inhalt der QuelleHP alloys are typically used as steam methane reforming tubes in the petrochemical industry. During service, they are exposed to temperatures between 700°C and 1000°C under gaz pressure of several MPa. Their as-cast microstructure, together with fine in-situ secondary precipitation, provide these alloys with an excellent resistance to creep deformation. Nevertheless, after long-time ageing, coarsening of secondary carbides leads to the weakening of the tubes and therefore to an accelerated damaging.The effects of some alloying elements (V, Ti/W) on secondary precipitation of M23C6 and NbC carbides were investigated through numerical simulations performed with TC-PRISMA software. On the basis of encouraging results in terms of precipitation optimization, two model HP-type alloys were cast at the laboratory and aged in the range of temperatures corresponding to service conditions. As-cast microstructures were first compared with an industrial "standard" alloy. Then, secondary precipitation were characterized for all the alloys and all ageing temperatures. Microstructural investigation highlighted the beneficial effect of vanadium and titanium/tungsten additions on secondary precipitation characteristics
Agode, Kofi Edoh. „Analyse et modélisation du comportement à l’usure des outils de coupe en carbure de tungstène pour différentes teneurs en cobalt lors de l’usinage de l’alliage de titane Ti-6Al-4V“. Electronic Thesis or Diss., Université de Lorraine, 2022. http://www.theses.fr/2022LORR0141.
Der volle Inhalt der QuelleDue to their high hardness and wear resistance, cemented carbide (WC-Co) is the main material used to manufacture machining tools and forming tooling, as well as wear parts requiring high hardness and high precision. The modification of tungsten carbide microstructure, and more particularly its cobalt content, is currently attracting the greatest interest from manufacturers to develop new grades tools with high performance, and then expand new markets.This thesis aims to study the effect of the cobalt content of carbide tools on the measured values and wear mechanisms when machining hard superalloys such as the aeronautical titanium alloys Ti-6Al-4V. Both experimental and numerical research work are devoted on one hand to the understanding of the microscopic damage mechanisms leading to the macroscopic wear of the WC-Co composite and on the other hand, to the influence of the cobalt content on the behavior of the WC-Co taking into account the mechanical-microstructure-damage coupling.On the basis of an experimental analysis, the identification of the macroscopic and microscopic physical phenomena involved at the tool/chip and tool/workpiece contact interfaces was conducted. Machining tests were firstly carried out on the tool-material couple WC-Co/Ti-6Al-4V with different cobalt contents for the tools (from 6 to 15%). In a second step, a tribological characterization of the same tool-material couple was carried out to evaluate the influence of the cobalt content and the contact conditions (sliding speed, applied force) on the friction coefficient and wear. However, the inaccessibility of the contact zones during machining and the tribological tests did not allow a complete description of the wear mechanisms observed, whether macroscopic mechanisms (adhesion, abrasion, deformation, ...), or microscopic mechanisms (cracking, damage of the WC and Co phases). The numerical simulation using finite elements (FE) proved to be a very interesting complementary tool for the analysis of these wear mechanisms.Our modeling strategy focused on the response of WC-Co at the microstructure scale for the thermomechanical loading close to that obtained by machining. The proposed model takes into account the behavior of the WC and Co phases separately and that of the interfaces WC-WC and WC-Co of the composite. This strategy allowed to study and identify parameters influencing the behavior of the microstructure from the elastic stage to the damage initiation. A good agreement was obtained between the results of the numerical behavior at the initiation of damage in the microstructure and those of the experimental observations in terms of the effects of the cobalt content in the tungsten carbide and of the applied machining conditions
Gianni, Lorenzo. „Electrodialytic recovery of tungsten and cobalt from tungsten carbide scrap“. Master's thesis, Alma Mater Studiorum - Università di Bologna, 2022.
Den vollen Inhalt der Quelle findenDeshpande, Pranav Kishore. „Infrared Processed Copper-Tungsten Carbide Composites“. University of Cincinnati / OhioLINK, 2002. http://rave.ohiolink.edu/etdc/view?acc_num=ucin1025107651.
Der volle Inhalt der QuelleKelley, Andrew III. „Tungsten carbide-cobalt by Three Dimensional Printing“. Thesis, Massachusetts Institute of Technology, 1998. http://hdl.handle.net/1721.1/32316.
Der volle Inhalt der QuelleIncludes bibliographical references (p. 69-70).
Three Dimensional Printing is an additive manufacturing process for rapid prototyping ceramic and metallic parts [Sachs, et al, 1990]. Green (not sintered) tungsten carbide-cobalt parts must have a density greater than 50% of the theoretical density, 14.9 g/cc, for proper sintering and post-processing. Two approaches were assessed for feasibility and robustness: printing slurry into tungsten carbide-cobalt spray dried powder and printing a solvent in spray dried tungsten carbide powder that readily dissolves. For slurry administered to a powder bed of solid, spherical particles, it has been found that the resulting packing primitive packing fraction increases almost linearly with the volume loading of the slurry over a range of powder size. The increase in density is approximately half what would be calculated by assuming that the slurry fills all the porosity in the powder bed. The maximum green density achieved by printing slurry into a spray dried tungsten carbide-cobalt bed was 41%, midway between the lower bound calculated by assuming the vehicle in the slurry infiltrates only the large pores between the spray dried power and the upper bound calculated by assuming that the vehicle of the slurry also infiltrates the find pores within a spray dried granule. A re-dispersible spray dried powder (38-53 micron size range) was fabricated using only the Duramax 3007 dispersant as the binder. This powder redisperses in water. Administering a drop of water to this powder resulted in primitives with 47% packing density, but which had significant quantities of 80 micron voids.
(cont.) Several lines of evidence pointed to the hypothesis that the voids were the result of trapped air. Two methods were successfully employed to nearly eliminate such voids. In one approach, the droplet of water wvas administered to the powder bed under a vacuum of between 25 and 40 torr and air was admitted to the chamber to 1 atmosphere after different intervals of time ranging from 30 seconds to 10 minutes. In another approach, the ability of water to absorb CO₂ was used to "getter" any trapped gas into the liquid. Water was administered to a powder bed under a CO₂ environment at room temperature. After a 2 minute period, intended to allow the spray dried powder to substantially re-disperse, the temperture of the powder bed was lowered to 0-5 degrees Centigrade in order to increase the amount of CO₂ which could be absorbed in the water and "switch on" the gettering of the trapped gas.Controls were run with the same procedure in air. The primitives made under CO₂ were nearly void free and had densities as high as 52%, while the controls were not significantly different than primitives made at room temperature in air.
by Andrew Kelley, III.
S.M.
Deshpande, Pranav K. „Copper-tungsten carbide composites with infrared processing“. Cincinnati, Ohio : University of Cincinnati, 2002. http://rave.ohiolink.edu/etdc/view?acc%5Fnum=ucin1025107651.
Der volle Inhalt der QuelleBücher zum Thema "Tungstene carbide"
Kurlov, Alexey S., und Aleksandr I. Gusev. Tungsten Carbides. Cham: Springer International Publishing, 2013. http://dx.doi.org/10.1007/978-3-319-00524-9.
Der volle Inhalt der QuelleBrookes, Kenneth J. A. World directory and handbookof hardmetals. 4. Aufl. East Barnet: International Carbide Data, 1987.
Den vollen Inhalt der Quelle findenBrookes, Kenneth J. A. World directory and handbook of hardmetals. 4. Aufl. Barnet, Herts: International Carbide Data, 1987.
Den vollen Inhalt der Quelle findenLiu, Kui. Tungsten carbide: Processing and applications. Rijeka, Croatia: InTech, 2012.
Den vollen Inhalt der Quelle findenUpadhyaya, G. S., und Gopal S. Upadhyaya. Cemented tungsten carbides: Production, properties, and testing. Westwood, N.J: Noyes Publications, 1998.
Den vollen Inhalt der Quelle findenBrookes, Kenneth J. A. World directory and handbook of hardmetals and hard materials. 6. Aufl. East Barnet: International Carbide Data, 1996.
Den vollen Inhalt der Quelle findenWorld directory and handbook of hardmetals and hard materials. 5. Aufl. East Barnet: International Carbide Data, 1992.
Den vollen Inhalt der Quelle findenCenter, Langley Research, Hrsg. Tensile behavior of tungsten and tungsten-alloy wires from 1300 to 1600 k. Cleveland, Ohio: National Aeronautics and Space Administration, Lewis Research Center, 1988.
Den vollen Inhalt der Quelle findenH, Titran Robert, und United States. National Aeronautics and Space Administration., Hrsg. Tensile and stress-rupture behavior of hafnium carbide dispersed molybdenum and tungsten based alloy wires. [Washington, DC]: National Aeronautics and Space Administration, 1993.
Den vollen Inhalt der Quelle findenH, Titran Robert, und United States. National Aeronautics and Space Administration., Hrsg. Tensile and stress-rupture behavior of hafnium carbide dispersed molybdenum and tungsten based alloy wires. [Washington, DC]: National Aeronautics and Space Administration, 1993.
Den vollen Inhalt der Quelle findenBuchteile zum Thema "Tungstene carbide"
Kurlov, Alexey S., und Aleksandr I. Gusev. „Nanocrystalline Tungsten Carbide“. In Tungsten Carbides, 109–89. Cham: Springer International Publishing, 2013. http://dx.doi.org/10.1007/978-3-319-00524-9_4.
Der volle Inhalt der QuelleKurlov, Alexey S., und Aleksandr I. Gusev. „Introduction“. In Tungsten Carbides, 1–3. Cham: Springer International Publishing, 2013. http://dx.doi.org/10.1007/978-3-319-00524-9_1.
Der volle Inhalt der QuelleKurlov, Alexey S., und Aleksandr I. Gusev. „Phases and Equilibria in the W–C and W–Co–C Systems“. In Tungsten Carbides, 5–56. Cham: Springer International Publishing, 2013. http://dx.doi.org/10.1007/978-3-319-00524-9_2.
Der volle Inhalt der QuelleKurlov, Alexey S., und Aleksandr I. Gusev. „Ordering of Tungsten Carbides“. In Tungsten Carbides, 57–108. Cham: Springer International Publishing, 2013. http://dx.doi.org/10.1007/978-3-319-00524-9_3.
Der volle Inhalt der QuelleKurlov, Alexey S., und Aleksandr I. Gusev. „Hardmetals WC–Co Based on Nanocrystalline Powders of Tungsten Carbide WC“. In Tungsten Carbides, 191–237. Cham: Springer International Publishing, 2013. http://dx.doi.org/10.1007/978-3-319-00524-9_5.
Der volle Inhalt der QuelleStorms, E. K. „Tungsten Carbides“. In Inorganic Reactions and Methods, 314–15. Hoboken, NJ, USA: John Wiley & Sons, Inc., 2007. http://dx.doi.org/10.1002/9780470145265.ch122.
Der volle Inhalt der QuelleShabalin, Igor L. „Tungsten Carbides“. In Ultra-High Temperature Materials IV, 11–829. Cham: Springer International Publishing, 2022. http://dx.doi.org/10.1007/978-3-031-07175-1_2.
Der volle Inhalt der QuelleIshizawa, Y., und T. Tanaka. „Fermi surface of hexagonal tungsten carbide“. In The Chemistry of Transition Metal Carbides and Nitrides, 121–33. Dordrecht: Springer Netherlands, 1995. http://dx.doi.org/10.1007/978-94-009-1565-7_6.
Der volle Inhalt der QuelleLiu, Kui, Hao Wang und Xinquan Zhang. „Ductile Mode Cutting of Tungsten Carbide“. In Springer Series in Advanced Manufacturing, 149–77. Singapore: Springer Singapore, 2019. http://dx.doi.org/10.1007/978-981-32-9836-1_8.
Der volle Inhalt der QuelleFischer, E. O., D. Wittmann, A. Mayr und A. Mcdermott. „Carbyne Complexes of Tungsten“. In Inorganic Syntheses, 40–43. Hoboken, NJ, USA: John Wiley & Sons, Inc., 2007. http://dx.doi.org/10.1002/9780470132579.ch9.
Der volle Inhalt der QuelleKonferenzberichte zum Thema "Tungstene carbide"
Wank, A., C. Schmengler, K. Müller-Roden, F. Beck und T. Schläfer. „Aptitude of Different Types of Carbides for Production of Durable Rough Surfaces by Laser Dispersing“. In ITSC2017, herausgegeben von A. Agarwal, G. Bolelli, A. Concustell, Y. C. Lau, A. McDonald, F. L. Toma, E. Turunen und C. A. Widener. DVS Media GmbH, 2017. http://dx.doi.org/10.31399/asm.cp.itsc2017p0414.
Der volle Inhalt der QuellePrabin, A., K. S. Anvitha und R. Sathish. „Corrosion Inhibition on Cemented Tungsten Carbides“. In Euro Powder Metallurgy 2023 Congress & Exhibition. EPMA, 2023. http://dx.doi.org/10.59499/ep235763660.
Der volle Inhalt der QuelleFiala, P., R. Hepp und A. Zikin. „Alloyed Carbides Beyond WC as a New Material Platform for Solving Challenges in Hardfacing“. In ITSC2017, herausgegeben von A. Agarwal, G. Bolelli, A. Concustell, Y. C. Lau, A. McDonald, F. L. Toma, E. Turunen und C. A. Widener. DVS Media GmbH, 2017. http://dx.doi.org/10.31399/asm.cp.itsc2017p0408.
Der volle Inhalt der QuelleLyphout, C., J. Kitamura, K. Sato, J. Yamada und S. Dizdar. „Tungsten Carbide Deposition Processes for Hard Chrome Alternative: Preliminary Study of HVAF vs. HVOF Thermal Spray Processes“. In ITSC2013, herausgegeben von R. S. Lima, A. Agarwal, M. M. Hyland, Y. C. Lau, G. Mauer, A. McDonald und F. L. Toma. ASM International, 2013. http://dx.doi.org/10.31399/asm.cp.itsc2013p0506.
Der volle Inhalt der QuelleLe Bastard, Avigae¨le, Re´mi Batisse und Vincent Gaschignard. „Investigation of a Non-Destructive Method to Characterize Material Mechanical Properties of Pipelines in Service“. In 2008 7th International Pipeline Conference. ASMEDC, 2008. http://dx.doi.org/10.1115/ipc2008-64267.
Der volle Inhalt der QuelleVuoristo, P., J. Laurila, T. Mäntylä, K. Niemi, S. Rekola und S. Ahmaniemi. „Surface Changes in Thermally Sprayed Hard Coatings by Wear of Different Abrasives“. In ITSC2004, herausgegeben von Basil R. Marple und Christian Moreau. ASM International, 2004. http://dx.doi.org/10.31399/asm.cp.itsc2004p1046.
Der volle Inhalt der QuelleScrivani, A., A. Giorgetti, F. Bianchi, L. Campanini, L. Coppelletti und H. Keller. „Thermal Spray Coatings for Application in Petrochemical Field: A Comparison of Tungsten Carbide, Chromium Carbide and Inconel 625“. In ITSC 2012, herausgegeben von R. S. Lima, A. Agarwal, M. M. Hyland, Y. C. Lau, C. J. Li, A. McDonald und F. L. Toma. ASM International, 2012. http://dx.doi.org/10.31399/asm.cp.itsc2012p0540.
Der volle Inhalt der QuelleGorlenko, Aleksandr, Sergey Davydov und Mikhail Shevtsov. „STRENGTHENING OF CARBIDE STEEL SURFACE BY TUNGSTEN CARBIDE POWDER BY PLASTIC DEFORMATION“. In PROBLEMS OF APPLIED MECHANICS. Bryansk State Technical University, 2020. http://dx.doi.org/10.30987/conferencearticle_5fd1ed04a82ac0.47164745.
Der volle Inhalt der QuelleHirata, G. A., O. Contreras, M. H. Farías und L. Cota-Araiza. „Stoichiometric tungsten carbide coatings“. In The 8th Latin American congress on surface science: Surfaces , vacuum, and their applications. AIP, 1996. http://dx.doi.org/10.1063/1.51119.
Der volle Inhalt der QuelleSrinivasan, Suresh, Jessica M. Marshall, Joe Gillham und Gurdev Singh. „Tungsten carbide for radiation shielding: A comprehensive review“. In Euro Powder Metallurgy 2023 Congress & Exhibition. EPMA, 2023. http://dx.doi.org/10.59499/ep235765427.
Der volle Inhalt der QuelleBerichte der Organisationen zum Thema "Tungstene carbide"
Dandekar, Dattatraya P. Spall Strength of Tungsten Carbide. Fort Belvoir, VA: Defense Technical Information Center, September 2004. http://dx.doi.org/10.21236/ada427318.
Der volle Inhalt der QuelleGluth, Jeffrey Weston, Clint Allen Hall, Tracy John Vogler und Dennis Edward Grady. Dynamic compaction of tungsten carbide powder. Office of Scientific and Technical Information (OSTI), April 2005. http://dx.doi.org/10.2172/922764.
Der volle Inhalt der Quellemazo, isacco, alberto molinari und vincenzo sglavo. Electrical Resistance Flash Sintering of Tungsten Carbide. Peeref, September 2022. http://dx.doi.org/10.54985/peeref.2209p1889967.
Der volle Inhalt der QuelleReinhart, William Dodd, Tom Finley, III Thornhill, Tracy John Vogler und C. Scott Alexander. Expansion into vacuum of a shocked tungsten carbide-epoxy mixture. Office of Scientific and Technical Information (OSTI), März 2009. http://dx.doi.org/10.2172/983671.
Der volle Inhalt der QuelleZ. Zak Fang, H. Y. Sohn. Development of Bulk Nanocrystalline Cemented Tungsten Carbide for Industrial Applicaitons. Office of Scientific and Technical Information (OSTI), März 2009. http://dx.doi.org/10.2172/950043.
Der volle Inhalt der QuelleDemaske, Brian. Mesoscale simulations of pressure-shear loading of granular tungsten carbide. Office of Scientific and Technical Information (OSTI), Januar 2022. http://dx.doi.org/10.2172/2002918.
Der volle Inhalt der QuelleChen, Tianju, Bipul Barua, Tianchen Hu, Mark Messner und Tahany El-Wardany. An ICME Modeling Framework for Titanium/Tungsten-Carbide Metal Matrix Composites. Office of Scientific and Technical Information (OSTI), Mai 2023. http://dx.doi.org/10.2172/1985051.
Der volle Inhalt der QuelleKolopus, James A., und Lynn A. Boatner. Single-Crystal Tungsten Carbide in High-Temperature In-Situ Additive Manufacturing Characterization. Office of Scientific and Technical Information (OSTI), Mai 2017. http://dx.doi.org/10.2172/1361361.
Der volle Inhalt der QuelleConrad, Hans, und Jay Narayan. Grain Size Hardening and Softening in Tungsten Carbide at Low Homologous Temperatures. Fort Belvoir, VA: Defense Technical Information Center, Januar 2003. http://dx.doi.org/10.21236/ada422872.
Der volle Inhalt der QuelleDavid Moy, Jun Ma, Robert Hoch, Jim Leacock, Jason Willey, Asif Chishti, Fabio RIbeiro et al. New Nanoscale Catalysts Based on Molybdenum and Tungsten Carbides and Oxycarbides. Office of Scientific and Technical Information (OSTI), August 2002. http://dx.doi.org/10.2172/799250.
Der volle Inhalt der Quelle