Auswahl der wissenschaftlichen Literatur zum Thema „Epoxy Mold Compound“
Geben Sie eine Quelle nach APA, MLA, Chicago, Harvard und anderen Zitierweisen an
Inhaltsverzeichnis
Machen Sie sich mit den Listen der aktuellen Artikel, Bücher, Dissertationen, Berichten und anderer wissenschaftlichen Quellen zum Thema "Epoxy Mold Compound" bekannt.
Neben jedem Werk im Literaturverzeichnis ist die Option "Zur Bibliographie hinzufügen" verfügbar. Nutzen Sie sie, wird Ihre bibliographische Angabe des gewählten Werkes nach der nötigen Zitierweise (APA, MLA, Harvard, Chicago, Vancouver usw.) automatisch gestaltet.
Sie können auch den vollen Text der wissenschaftlichen Publikation im PDF-Format herunterladen und eine Online-Annotation der Arbeit lesen, wenn die relevanten Parameter in den Metadaten verfügbar sind.
Zeitschriftenartikel zum Thema "Epoxy Mold Compound"
Kumari, Pinki, Kuldeep Singh und Anuj Singal. „Reducing the Hygroscopic Swelling in MEMS Sensor using Different Mold Materials“. International Journal of Electrical and Computer Engineering (IJECE) 10, Nr. 1 (01.02.2020): 494. http://dx.doi.org/10.11591/ijece.v10i1.pp494-499.
Der volle Inhalt der QuelleLakhera, Nishant, Sandeep Shantaram und AR Nazmus Sakib. „Adhesion Characteristics of Epoxy Molding Compound and Copper Leadframe Interface: Impact of Environmental Reliability Stresses“. International Symposium on Microelectronics 2017, Nr. 1 (01.10.2017): 000304–11. http://dx.doi.org/10.4071/isom-2017-wa53_009.
Der volle Inhalt der QuelleDeringer, Tim, und Dietmar Drummer. „The influence of mold temperature on thermoset in-mold forming“. Journal of Polymer Engineering 40, Nr. 3 (25.02.2020): 256–66. http://dx.doi.org/10.1515/polyeng-2019-0322.
Der volle Inhalt der QuelleSulong, Abu Bakar, Gan Tek Keong und Jaafar Sahari. „Effects of Molding Parameters and Addition of Fillers on Gate Chip Off Formation during the Degating Process in Transfer Molding“. Key Engineering Materials 447-448 (September 2010): 790–94. http://dx.doi.org/10.4028/www.scientific.net/kem.447-448.790.
Der volle Inhalt der QuelleChen, Hwe-Zhong, Wen-Hung Lee, Huei-Huang Lee, Durn-Yuan Huang, Shyang-Jye Chang und Sheng-Jye Hwang. „Effects of defrosting period on mold adhesion force of epoxy molding compound“. Asia-Pacific Journal of Chemical Engineering 4, Nr. 2 (März 2009): 161–68. http://dx.doi.org/10.1002/apj.186.
Der volle Inhalt der QuelleBrueckner, Julia, Michael Schwander, Moritz Jurgschat und Ramon Tuason. „Effective Inspection Methods for Advanced Packaging Technologies“. International Symposium on Microelectronics 2017, Nr. 1 (01.10.2017): 000563–68. http://dx.doi.org/10.4071/isom-2017-tha32_055.
Der volle Inhalt der QuelleHsu, Hsiang-Chen, Shih-Jeh Wu, Wen-Fei Lin und Boen Houng. „Reliability Design and Optimization Process on through Mold via using Ultrafast Laser“. Polymers and Polymer Composites 26, Nr. 1 (Januar 2018): 1–8. http://dx.doi.org/10.1177/096739111802600101.
Der volle Inhalt der QuelleLakhera, Nishant, Tom Battle, Sheila Chopin, Sandeep Shantaram und Akhilesh K. Singh. „Technique to predict reliability failure in side-gate transfer molded packages“. International Symposium on Microelectronics 2015, Nr. 1 (01.10.2015): 000696–701. http://dx.doi.org/10.4071/isom-2015-tha61.
Der volle Inhalt der QuelleMurali, Sarangapani, Bayaras Abito Danila und Zhang Xi. „Reliability of Coated and Alloyed Copper/Silver Ball Bonds“. International Symposium on Microelectronics 2017, Nr. 1 (01.10.2017): 000318–24. http://dx.doi.org/10.4071/isom-2017-wa55_128.
Der volle Inhalt der QuelleXu, Wen Jiao, und Shu Yu Lu. „Recycling of Thermosetting Epoxy Molding Compound Waste into PVC Composites: Effect of Silane Coupling Agent on Morphology and Physical Properties“. Advanced Materials Research 311-313 (August 2011): 1496–500. http://dx.doi.org/10.4028/www.scientific.net/amr.311-313.1496.
Der volle Inhalt der QuelleDissertationen zum Thema "Epoxy Mold Compound"
Tomas, Ariane. „Contribution à l’évaluation de la fiabilité des assemblages QFN et WLP : études thermo- et hygro-mécaniques des résines d’encapsulation“. Electronic Thesis or Diss., Bordeaux, 2023. http://www.theses.fr/2023BORD0460.
Der volle Inhalt der QuelleThis work is placed in the context of development and evaluation of packaging technology allowing heterogeneous integration. The objective of this thesis is to understand how the interaction between the mold compound and the dies influences the reliability of the component and can lead to failures linked to thermal and humidity stress. The objectives of this work are also to determine the influence of the choice of the resin and therefore of the material properties on the thermomechanical and hygromechanical behavior of the component. It is therefore a question of establishing a methodology for studying these behaviors through the analysis of encapsulation resins
Tomori, Oluwatosin Oyewole. „Machining of ceramic filled epoxy and its impact on injection mold Applications“. Thesis, Georgia Institute of Technology, 2002. http://hdl.handle.net/1853/16901.
Der volle Inhalt der QuelleWang, Zhi-Guo, und 王智國. „Modeling the Viscoelastic Properties of Epoxy Molding Compound during Post Mold Cure in IC Packaging“. Thesis, 2006. http://ndltd.ncl.edu.tw/handle/40139693337622112337.
Der volle Inhalt der Quelle國立成功大學
機械工程學系碩博士班
94
Epoxy molding compound (EMC) is a common material in electronic packages. Warpage after encapsulating in packaging process is always a problem to engineers. The experimental and simulation results of warpage of EMC-Cu and EMC-Si bi-laminates revealed that higher mold temperature caused larger warpage, and the packaging pressure effect upon warpage was less dominant. The simulation was based on P-V-T-C properties of EMC (, i.e. the relation between packing pressure, volume shrinkage, mold temperature and degree of cure). The experimental and simulation results of bi-laminates during non-pressed post mold cure (PMC) revealed that PMC could reduce the warpage. The simulation was based on the phenomenon that Tg changes during PMC. Under high-temperature for a long time such as PMC, EMC can behave like a viscoelastic material. Therefore viscoelasticity should be considered during the post mold cure process. Due to the lack of cure-dependent viscoelastic models, the objective of this thesis is therefore to construct a viscoelastic model with degree of cure as one of parameters. By dynamic mechanical analyzer (DMA) testing, the generalized Maxwell's model and Williams-Ladel-Ferry (WLF) equation of Hitachi 9200 compound were identified. By the measuring the loss and storage moduli of differently cured polymer at room temperature, the equation relating the degree of cure to cure shift factor was also proposed. WLF equation defines the relation between temperature and temperature shift factor(aT) while the forementioned shift equation defines the relation between degree of cure and cure shift factor(aC). These two relating equations define two kinds of shift factors. With these two relating equations, the relaxation modulus for any degree of cure and temperature can be defined.
Buchteile zum Thema "Epoxy Mold Compound"
Kitaoka, Satoshi, Naoki Kawashima, Keiji Maeda, Takaki Kuno und Yoshinori Noguchi. „Design of Mold Materials for Encapsulating Semiconductors Using Epoxy Compounds“. In Advanced Processing and Manufacturing Technologies for Structural and Multifunctional Materials, 19–26. Hoboken, NJ, USA: John Wiley & Sons, Inc., 2009. http://dx.doi.org/10.1002/9780470339718.ch3.
Der volle Inhalt der QuelleKitaoka, Satoshi, Naoki Kawashima, Keiji Maeda, Takaki Kuno und Yoshinori Noguchi. „Design of Mold Materials for Encapsulating Semiconductors Using Epoxy Molding Compounds“. In Materials Science Forum, 539–42. Stafa: Trans Tech Publications Ltd., 2007. http://dx.doi.org/10.4028/0-87849-462-6.539.
Der volle Inhalt der QuelleKonferenzberichte zum Thema "Epoxy Mold Compound"
Tomas, Ariane, Benoit Lambert, Helene Fremont, Nathalie Malbert und Nathalie Labat. „Epoxy Mold Compound Characterization for Modeling Packaging Reliability“. In 2022 23rd International Conference on Thermal, Mechanical and Multi-Physics Simulation and Experiments in Microelectronics and Microsystems (EuroSimE). IEEE, 2022. http://dx.doi.org/10.1109/eurosime54907.2022.9758842.
Der volle Inhalt der QuelleFan, Xuejun, und Vishal Nagaraj. „In-situ moisture desorption characterization of epoxy mold compound“. In 2012 13th Intl. Conf. on Thermal, Mechanical & Multi-Physics Simulation and Experiments in Microelectronics and Microsystems (EuroSimE). IEEE, 2012. http://dx.doi.org/10.1109/esime.2012.6191772.
Der volle Inhalt der QuelleWidodo, T. S., X. F. Brun, N. Tsunoda, Y. Ichige, S. Arata, C. Noda, S. Nomura und S. Kondo. „Selective Epoxy Mold Compound Slurry for Advanced Packaging Technology“. In 2022 IEEE 72nd Electronic Components and Technology Conference (ECTC). IEEE, 2022. http://dx.doi.org/10.1109/ectc51906.2022.00204.
Der volle Inhalt der QuelleArata, Shogo, Chiaki Noda, Yasuhiro Ichige, Satoyuki Nomura, T. S. Widodo, N. Tsunoda und X. F. Brun. „Selective and Tunable Slurry for Advanced Packaging Epoxy Mold Compound“. In 2022 IEEE International Interconnect Technology Conference (IITC). IEEE, 2022. http://dx.doi.org/10.1109/iitc52079.2022.9881294.
Der volle Inhalt der QuelleGarete, April Joy H., Marlon F. Fadullo und Reinald John S. Roscain. „Epoxy Mold Compound Curing Behavior and Mold Process Cure Time Interaction on Molded Package Performance“. In 2019 IEEE 21st Electronics Packaging Technology Conference (EPTC). IEEE, 2019. http://dx.doi.org/10.1109/eptc47984.2019.9026644.
Der volle Inhalt der QuelleFan, Haibo, Hugo Wong, Fei Wong, Kai Zhang und Haibin Chen. „Study of V-groove on Leadframe/Epoxy Mold Compound Delamination Improvement“. In 2019 20th International Conference on Electronic Packaging Technology(ICEPT). IEEE, 2019. http://dx.doi.org/10.1109/icept47577.2019.245333.
Der volle Inhalt der QuelleGschwandl, Mario, Peter Filipp Fuchs, Ivaylo Mitev, Mahesh Yalagach, Thomas Antretter, Tao Qi und Angelika Schingale. „Modeling of manufacturing induced residual stresses of viscoelastic epoxy mold compound encapsulations“. In 2017 IEEE 19th Electronics Packaging Technology Conference (EPTC). IEEE, 2017. http://dx.doi.org/10.1109/eptc.2017.8277557.
Der volle Inhalt der QuelleQian, Qiuxiao, und Yong Liu. „Board level solder reliability simulation for epoxy mold compound based power package“. In 2017 IEEE 19th Electronics Packaging Technology Conference (EPTC). IEEE, 2017. http://dx.doi.org/10.1109/eptc.2017.8277584.
Der volle Inhalt der QuelleGuillon, David, Andris Avots, Milad Maleki, Katrin Schlegel und Isabell Ehrler. „Impact of reliability tests on the adhesion of the epoxy mold compound“. In 2022 IEEE 72nd Electronic Components and Technology Conference (ECTC). IEEE, 2022. http://dx.doi.org/10.1109/ectc51906.2022.00094.
Der volle Inhalt der QuelleFernandez, Matthew M., Beila Angeles und Deo Navaja. „Epoxy Mold Compound Characterization and Cure Kinetics for Post Mold Isothermal Cure Improvement and Accelerated Reliability Assessment“. In 2019 IEEE 21st Electronics Packaging Technology Conference (EPTC). IEEE, 2019. http://dx.doi.org/10.1109/eptc47984.2019.9026594.
Der volle Inhalt der Quelle